SILVERPEAK-MGMT-MIB
AI MIB Summary
The SILVERPEAK-MGMT-MIB provides SNMP access to monitor and manage Silver Peak WAN optimization appliance operational status, including system health, interface statistics, and traffic flow metrics. It enables centralized network management systems to retrieve critical performance data and control parameters for Silver Peak edge devices.
This module defines the management variables used to manage and monitor appliance status.
Main OID:
silverpeakMgmtMIB.1.3.6.1.4.1.23867.3.1
32
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
32 total| Object Name |
|---|
silverpeakMgmtMIBThis module defines the management variables used to manage and monitor appliance status. MODULE-IDENTITY .1.3.6.1.4.1.23867.3.1 |
silverpeakMgmtMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.23867.3.1.1 |
silverpeakMgmtMIBScalars OBJECT IDENTIFIER .1.3.6.1.4.1.23867.3.1.1.1 |
spsSystemVersionSystem software version stringro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.23867.3.1.1.1.1 |
spsProductModelSystem product modelro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.23867.3.1.1.1.2 |
spsOperStatusThe current operational state of the appliance.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.23867.3.1.1.1.3 |
spsActiveAlarmCountThe number of active alarm entries in the alarm table - spsActiveAlarmTable, defined under silverpeakMgmtMIBTables subtree.ro INTEGER .1.3.6.1.4.1.23867.3.1.1.1.4 |
spsSystemUptimeThe amount of time in hundredth of a second since this NX was last initialized. Note that this is different from sysUpTime in the SNMPv2-MIB [RFC1907] because sysUpTime is the uptime of the network management portion of the system.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.23867.3.1.1.1.5 |
silverpeakMgmtMIBTables OBJECT IDENTIFIER .1.3.6.1.4.1.23867.3.1.1.2 |
spsActiveAlarmTableA list of the active alarm entries. This represents the fault conditions that are still active in the appliance. SEQUENCE OF ActiveAlarmEntry .1.3.6.1.4.1.23867.3.1.1.2.1 |
activeAlarmEntryThe active alarm entries that are still valid system faults. ActiveAlarmEntry .1.3.6.1.4.1.23867.3.1.1.2.1.1 |
spsActiveAlarmIndexAn index that uniquely identifies an entry in the active alarm table. INTEGER .1.3.6.1.4.1.23867.3.1.1.2.1.1.1 |
spsActiveAlarmSeqNumThe active alarm's sequence number at the time it was generated.ro SilverpeakSeqNum (SILVERPEAK-TC) .1.3.6.1.4.1.23867.3.1.1.2.1.1.2 |
spsActiveAlarmSeverityThe alarm severity for the active alarm.ro SilverpeakAlarmSeverity (SILVERPEAK-TC) .1.3.6.1.4.1.23867.3.1.1.2.1.1.3 |
spsActiveAlarmNameA short name for the active alarm.ro DisplayString .1.3.6.1.4.1.23867.3.1.1.2.1.1.4 |
spsActiveAlarmDescrA description for the active alarm.ro DisplayString .1.3.6.1.4.1.23867.3.1.1.2.1.1.5 |
spsActiveAlarmSourceThe source for the active alarm.ro DisplayString .1.3.6.1.4.1.23867.3.1.1.2.1.1.6 |
spsActiveAlarmTypeThe alarm type for the active alarm.ro DisplayString .1.3.6.1.4.1.23867.3.1.1.2.1.1.7 |
spsActiveAlarmAckedIdentifies if the user has acknowledged the alarm.ro SilverpeakYesNo (SILVERPEAK-TC) .1.3.6.1.4.1.23867.3.1.1.2.1.1.8 |
spsActiveAlarmActiveIdentifies if the alarm is currently active.ro SilverpeakYesNo (SILVERPEAK-TC) .1.3.6.1.4.1.23867.3.1.1.2.1.1.9 |
spsActiveAlarmClearableIdentifies if the user can manually clear the alarm.ro SilverpeakYesNo (SILVERPEAK-TC) .1.3.6.1.4.1.23867.3.1.1.2.1.1.10 |
spsActiveAlarmLogTimeThe value of sysUpTime when the alarm was generated.ro OCTET STRING .1.3.6.1.4.1.23867.3.1.1.2.1.1.11 |
spsActiveAlarmServiceAffectIdentifies if the alarm is service affecting.ro SilverpeakYesNo (SILVERPEAK-TC) .1.3.6.1.4.1.23867.3.1.1.2.1.1.12 |
spsActiveAlarmTypeIdAn ID that uniquely identifies a type of alarm. The following is a list of currently defined type IDs (ID listed below is in hexadecimal): ID Description ----- ------------------------------------------ 10000 Tunnel Remote ID is Misconfigured 10001 Tunnel state is Down 10002 Tunnel Vrrp IP is Misconfigured 10003 Tunnel keepalive version mismatch 10004 Tunnel wccp gid is misconfigured 10005 Tunnel software version mismatch 10006 Connecting to a non-VX-X is not supported. Please contact sales@silver-peak.com to discuss your options. 10007 Duplicate Silver Peak license detected on peer device. 20000 Tunnel Unexpected Traffic Class Error 30000 RAID Array is Degraded 30001 Disk is failed 30002 Disk is degraded 30003 FAN Failure detected 30004 System BYPASS mode 30005 LAN/WAN Fail-to-Wire Card Failure 30006 LAN/WAN Fail-to-Wire Card Relay Failure 30007 Encryption card H/W Failure 30008 Network Interface Admin Down 30009 Network Interface Link Down 3000a Management Interface Link Down 3000b Interface is Half Duplex 3000c Interface Speed is 10 Mbps 3000d Config DB disk full 3000e Operating System disk full 3000f File system disk full 30010 Datapath Internal loopback Test Failed 30011 WAN Next-Hop Unreachable 30012 VRRP instance is down 30013 VRRP State Master --> Backup 30014 WAN next hop router is learned on a LAN port (box is in backwards) 30015 Disk is not in service 30016 Disk is rebuilding 30017 Disk removed by operator 30018 LAN/WAN interfaces have different admin states 30019 LAN/WAN interfaces have different link carrier states 3001a LAN/WAN interface has been shutdown due to link propagation of paired interface 3001b Disk SMART threshold exceeded 3001c Cluster peer is down 3001d Bonding members have different speed/duplex 3001e WCCP adjacency(ies) down 3001f WCCP assignment table mismatch 30020 Power supply not connected, not powered or failed 30021 NIC interface failure 30022 LAN Next-Hop Unreachable 30023 Unexpected system restart 30024 Insufficient configured memory size for this virtual appliance 30025 Insufficient configured processor count for this virtual appliance 30026 Insufficient configured disk storage for this virtual appliance 40000 Software upgrade process has failed 40001 System is Low on resources 40002 Significant change in time of day has occurred, and might compromise statistics. 40003 The licensing for this virtual appliance has expired. 40004 There is no license installed on this virtual appliance. 40005 A disk self test has been performed. The system will require a reboot after the test. 40006 The private key is invalid. 40007 The certificate is not yet valid. 40008 The certificate has expired. 40009 The NTP server is unreachable. 50001 WAN-side transmit throughput TCA 50002 LAN-side receive throughput TCA 50003 Total number of optimized flows TCA 50004 Total number of flows TCA 50005 File-system utilization TCA 50006 Tunnel latency TCA 50007 Tunnel loss pre-FEC TCA 50008 Tunnel loss post-FEC TCA 50009 Tunnel OOP pre-POC TCA 5000a Tunnel OOP post-POC TCA 5000b Tunnel utilization TCA 5000c Tunnel reduction TCA ----- ------------------------------------------ro INTEGER .1.3.6.1.4.1.23867.3.1.1.2.1.1.13 |
silverpeakMgmtMIBConformance OBJECT IDENTIFIER .1.3.6.1.4.1.23867.3.1.2 |
silverpeakMgmtMIBCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.23867.3.1.2.1 |
silverpeakMgmtComplianceThe compliance statement for agents implementing silverpeakMgmtMIB. Unknown .1.3.6.1.4.1.23867.3.1.2.1.1 |
silverpeakMgmtMIBGroups OBJECT IDENTIFIER .1.3.6.1.4.1.23867.3.1.2.2 |
silverpeakMgmtGroupA collection of objects used to retrieve management information from Silverpeak Systems appliances. Unknown .1.3.6.1.4.1.23867.3.1.2.2.1 |
silverpeakMgmtNotifyGroupA collection of the Notifications supported in the management MIB. Unknown .1.3.6.1.4.1.23867.3.1.2.2.3 |
silverpeakMgmtMIBNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.23867.4.1 |
spsNotifyAlarmA notification that the system has just generated and alarm. NOTIFICATION-TYPE .1.3.6.1.4.1.23867.4.1.1 |