SHIVA-AT-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for SHIVA-AT-MIB.
21
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
21 total| Object Name |
|---|
IMPORTSThe number of entries which were removed from
routing table because the aging algorithm
indicated that they were invalid.ro INTEGER -- should be Counter .1.3.6.1.4.1.166.4.2.1 |
tRTMPEntryDeletesThe number of entries which were removed from the
routing table for any reason other than aging, for
instance, due to a command from a Network
Management station.ro INTEGER -- should be Counter .1.3.6.1.4.1.166.4.2.2 |
tRTMPEntryEqualReplacesThe number of entries whose route was replaced by
another route with the same hop count.ro INTEGER -- should be Counter .1.3.6.1.4.1.166.4.2.3 |
tRTMPEntryBetterReplacesThe number of entries whose route was replaced by
another route with a lower hop count.ro INTEGER -- should be Counter .1.3.6.1.4.1.166.4.2.4 |
tRTMPEntryAddsThe number of new entries which have been added to
the table.ro INTEGER -- should be Counter .1.3.6.1.4.1.166.4.2.5 |
tRTMPZeroCountersWriting this variable causes all the RTMP variables
in this group to be set to zero.rw Enumeration .1.3.6.1.4.1.166.4.2.6 |
tZIPDeletesThe number of Zones which have been deleted from the
Zone Table.ro INTEGER -- Should be Counter .1.3.6.1.4.1.166.4.2.7 |
tZIPAddsThe number of Zones which have been added to the
Zone Table.ro INTEGER -- Should be Counter .1.3.6.1.4.1.166.4.2.8 |
tZIPZeroCountersWriting this variable causes all the ZIP variables
in this group to be set to zero.rw Enumeration .1.3.6.1.4.1.166.4.2.9 |
tAARPClearCacheWriting this variable clears the AARP Cache.rw Enumeration .1.3.6.1.4.1.166.4.2.10 |
tKIPRoutesValidThis variable can be used to force KIP to reacquire its
configuration information.rw Enumeration .1.3.6.1.4.1.166.4.2.11 |
tNBPDeviceObjectThe NBP name used to advertise this device's primary
NVE on the LAN interface.ro OCTET STRING .1.3.6.1.4.1.166.4.2.12 |
tNBPDeviceTypeThe NBP type used to advertise this device's primary
NVE on the LAN interface.ro OCTET STRING .1.3.6.1.4.1.166.4.2.13 |
tNBPDeviceZoneThe zone in which this device registers its primary
NVE on the LAN interface.ro OCTET STRING .1.3.6.1.4.1.166.4.2.14 |
tNBPDeviceSocketThe DDP socket number used by the device in NBP
Responses for its primary NVE registered on the LAN
interface.ro INTEGER .1.3.6.1.4.1.166.4.2.15 |
tATDialinNetworkThe AppleTalk network number in which AppleTalk
dialin users appear. When
tATDialInPacketDeliveryMode is routing(1) this value
corresponds to the configured dialin network number.
When tATDialInPacketDeliveryMode is
endNodeForwarding(2) this value corresponds to the
network number of the LAN interface. Note that when
endNodeForwarding(2) it is possible that not all
dialin clients have addresses on this network because
there may not have been enough available node ids to
obtain addresses for all of the clients. In this
case another network in the extended range of the LAN
interface may be used for the remaining clients'
addresses. Ideally this should be a table of clients
with their dialin addresses.ro OCTET STRING .1.3.6.1.4.1.166.4.2.16 |
tATDialinZoneThe zone with which tATDialinNetwork is associated.ro OCTET STRING .1.3.6.1.4.1.166.4.2.17 |
tATRoutingModeThe routing behavior of this device for AppleTalk.
If the device is configured as conformingRouter(1) or
seedRouter(2) then it will behave as an AppleTalk
router on the LAN interface, and will route packets to
all interfaces. If it is a conformingRouter(1) then
it will learn its configuration for the LAN interface
from other routers on that interface's
directly-connected network. If it is a seedRouter(2)
then it will use the configured LAN interface
parameters.
If the device is configured as endNode(3) it will
behave as an AppleTalk endnode on the LAN interface.
other(4) is provided in the event a value is returned
which does not match any of the other enumerated
values. It is not expected that this will happen.ro Enumeration .1.3.6.1.4.1.166.4.2.18 |
tATDialinPacketDeliveryModeThe method used to deliver packets to and from
Appletalk dialin clients.
If the device is configured as routing(1) it will use
routing tables to deliver packets to and from dialin
clients, which will be homed on an internal virtual
interface (port). Technically, the value routing(1)
is only valid if the device is acting as a router
(the value of tATRoutingMode is conformingRouter(1)
or seedRouter(2)).
If the device is configured to use
endNodeForwarding(2) then it will obtain addresses
for dialin users in the LAN network range, and will
defend those addresses. Packets to and from dialin
clients will be forwarded. Technically the device
may be configured as endNodeForwarding(2) when
tATRoutingMode is any of: conformingRouter(1),
seedRouter(2), or endNode(3).
other(3) is provided in the event a value is returned
which does not match any of the other enumerated
values. It is not expected that this will happen.ro Enumeration .1.3.6.1.4.1.166.4.2.19 |
tRTMPEntryTotalThe number of network (range) entries in the
device's RTMP Table. This value is not cleared by
the tRTMPZeroCounters switch.ro INTEGER .1.3.6.1.4.1.166.4.2.20 |
tZoneTotalThe number of AppleTalk zones for which the device
has learned one or more associated nets or net
ranges. This value is not cleared by
the tZIPZeroCounters switch.ro INTEGER .1.3.6.1.4.1.166.4.2.21 |