SATELCOM-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for SATELCOM-MIB.
438
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
438 total| Object Name |
|---|
satelcom OBJECT IDENTIFIER .1.3.6.1.4.1.397 |
RFC1213-MIB Unknown .1.3.6.1.4.1.397 |
errorLogReportEnterprise Specific trap for MegaPAC.
The Error Log entry in ascii format TRAP-TYPE .1.3.6.1.4.1.397.0.0 |
sysRestartEnterprise Specific trap for MegaPAC System restart. TRAP-TYPE .1.3.6.1.4.1.397.0.1 |
configChangeEnterprise Specific trap for MegaPAC Configuration Change. TRAP-TYPE .1.3.6.1.4.1.397.0.32 |
vcpConnectEnterprise Specific trap for MegaPAC VCP Connect. TRAP-TYPE .1.3.6.1.4.1.397.0.33 |
vcpDisconnectEnterprise Specific trap for MegaPAC VCP Disconnect. TRAP-TYPE .1.3.6.1.4.1.397.0.34 |
billThreshReachedEnterprise Specific trap for MegaPAC- threshold reached for No. of BILLING records outstanding. TRAP-TYPE .1.3.6.1.4.1.397.0.35 |
linkNoResponseEnterprise Specific trap for MegaPAC Link Not Responding. TRAP-TYPE .1.3.6.1.4.1.397.0.96 |
linkCarrierLossEnterprise Specific trap for MegaPAC Link Carrier Loss. TRAP-TYPE .1.3.6.1.4.1.397.0.97 |
linkAddressErrEnterprise Specific trap for MegaPAC Link Address Error. TRAP-TYPE .1.3.6.1.4.1.397.0.98 |
frameLessThan2Enterprise Specific trap for MegaPAC Link Frame < 2 BYTES. TRAP-TYPE .1.3.6.1.4.1.397.0.99 |
ifieldTooLargeEnterprise Specific trap for MegaPAC Link I-Field too Large. TRAP-TYPE .1.3.6.1.4.1.397.0.100 |
linkRestartEnterprise Specific trap for MegaPAC Link restart. TRAP-TYPE .1.3.6.1.4.1.397.0.103 |
linkBlockedEnterprise Specific trap for MegaPAC LINK BLOCKED (Flow controlled). TRAP-TYPE .1.3.6.1.4.1.397.0.104 |
linkDisconnectEnterprise Specific trap for MegaPAC Link Disconnected. TRAP-TYPE .1.3.6.1.4.1.397.0.105 |
linkFrmrRecvdEnterprise Specific trap for MegaPAC Link FRMR received. TRAP-TYPE .1.3.6.1.4.1.397.0.112 |
linkDmResponseEnterprise Specific trap for MegaPAC Link DM response. TRAP-TYPE .1.3.6.1.4.1.397.0.113 |
linkBadNrEnterprise Specific trap for MegaPAC Link Bad N(r). TRAP-TYPE .1.3.6.1.4.1.397.0.114 |
linkDownEnterprise Specific trap for MegaPAC Link Down. TRAP-TYPE .1.3.6.1.4.1.397.0.115 |
linkFrmrSentEnterprise Specific trap for MegaPAC Link FRMR sent. TRAP-TYPE .1.3.6.1.4.1.397.0.116 |
crcThreshExceededEnterprise Specific trap for MegaPAC CRC Threshold Exceeded. TRAP-TYPE .1.3.6.1.4.1.397.0.117 |
linkManRestartEnterprise Specific trap for MegaPAC Link Manual restart. TRAP-TYPE .1.3.6.1.4.1.397.0.121 |
testIndicationResponseEnterprise Specific trap for MegaPAC 'TEST' command Indication/Response. TRAP-TYPE .1.3.6.1.4.1.397.0.122 |
interfaceFailureEnterprise Specific trap for MegaPAC Inteface (e.g. chip) failure. TRAP-TYPE .1.3.6.1.4.1.397.0.123 |
xidComRecvdEnterprise Specific trap for MegaPAC XID command received. TRAP-TYPE .1.3.6.1.4.1.397.0.124 |
bufferOverrunEnterprise Specific trap for MegaPAC Buffer Overrun Error. TRAP-TYPE .1.3.6.1.4.1.397.0.166 |
connectTimeWarnEnterprise Specific trap for MegaPAC Connect Time Warning. TRAP-TYPE .1.3.6.1.4.1.397.0.200 |
isdnNameAssignedEnterprise Specific trap for MegaPAC ISDN/V25 bis Name Assigned. TRAP-TYPE .1.3.6.1.4.1.397.0.230 |
isdnNameDeAassignedEnterprise Specific trap for MegaPAC ISDN/V25 bis Name De-Assigned. TRAP-TYPE .1.3.6.1.4.1.397.0.231 |
products OBJECT IDENTIFIER .1.3.6.1.4.1.397.1 |
megaPAC-E-cpu-C OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.1 |
megaPAC-N-series OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.2 |
megaPAC-E-cpu-D OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.3 |
megaCARD OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.4 |
arm-Router OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.5 |
megaPAC-V-cpu-8 OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.6 |
megaPAC-V-cpu-16 OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.7 |
megaPAC-V-cpu-68040 OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.8 |
megaPAD OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.9 |
megapac-2001 OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.10 |
micropad-2 OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.11 |
micropad-4 OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.12 |
micropad-8 OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.13 |
duo-Card-MBOX OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.14 |
duo-Card-System OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.15 |
megaBox-CPU-C OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.16 |
megaBox-CPU-D OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.17 |
megaBox-CPU-E OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.18 |
megaPac-E-CPU-C-Dual OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.19 |
megaPac-E-CPU-D-Dual OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.20 |
megaPac-E-CPU-E-Dual OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.21 |
megaPac-E-CPU-C-Dual-Fan OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.22 |
megaPac-E-CPU-D-Dual-Fan OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.23 |
megaPac-E-CPU-E-Dual-Fan OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.24 |
megaPac-E-CPU-C-Dual-Fan-48V OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.25 |
megaPac-E-CPU-D-Dual-Fan-48V OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.26 |
megaPac-E-CPU-E-Dual-Fan-48V OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.27 |
megaPAC-E-cpu-E OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.28 |
megaPac-V-Dual-PSU OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.29 |
megaPac-V-Dual-PSU-48V OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.30 |
megapac-20EM OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.31 |
megapac-21EM OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.32 |
megapac-2002 OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.33 |
megapac-2003 OBJECT IDENTIFIER .1.3.6.1.4.1.397.1.34 |
base OBJECT IDENTIFIER .1.3.6.1.4.1.397.2 |
baseVersionSoftware Version.
The software version currently running. Defined as YMMR (i.e.
Year, Month, Revisionro DisplayString .1.3.6.1.4.1.397.2.1 |
baseRestartTimeBASE Restart Time.
The time and data of the last system restart (i.e. power-on
or last BOOT)ro DisplayString .1.3.6.1.4.1.397.2.2 |
baseMaxPacketSizeNode Maximum Packet Size.
The maximum single buffer size available on the MegaPAC.ro INTEGER .1.3.6.1.4.1.397.2.3 |
baseBuffPoolMaxNode Buffer Pool Maximum.
The maximum number of buffers available temporary storage of
transitting data.ro INTEGER .1.3.6.1.4.1.397.2.4 |
baseBuffPoolNowNode Current Buffer Pool.
The current number of free buffers available temporary storage of
transitting data.ro INTEGER .1.3.6.1.4.1.397.2.5 |
baseBufferPoolLowestNode Buffer Pool Lowest.
The lowest value the buffer pool has ever reached.ro INTEGER .1.3.6.1.4.1.397.2.6 |
baseBufferPoolEmptyNode Buffer Pool Empty.
The number of times that the free buffer pool has fallen below
the minimum buffer threshold 'baseBuffThreshold'.ro INTEGER .1.3.6.1.4.1.397.2.7 |
baseStatBufferThresholdNode Buffer Threshold.
When the number of buffers in the free buffer pool reaches
this threshold, flow control will occur.ro INTEGER .1.3.6.1.4.1.397.2.8 |
baseMemorySizeNode Memory Size.
The size of the system memory installed in the MegaPAC.ro INTEGER .1.3.6.1.4.1.397.2.9 |
baseDataFramesInNode Frames In.
The total number of frames received by the MegaPAC.ro Counter .1.3.6.1.4.1.397.2.10 |
baseDataFramesOutNode Frames Out.
The total number of frames transmitted by the MegaPAC.ro Counter .1.3.6.1.4.1.397.2.11 |
baseDataFrameRateInNode Frame Rate In.
The rate measured in frames per second that the MegaPAC
is currently receiving frames.ro Counter .1.3.6.1.4.1.397.2.12 |
baseDataFrameRateOutNode Frames Rate Out.
The rate measured in frames per second that the MegaPAC
is currently transmitting frames.ro Counter .1.3.6.1.4.1.397.2.13 |
baseTotalCallSetUpsNode Total Call Set ups.
The total number of calls successfully established by the
MegaPAC.ro Counter .1.3.6.1.4.1.397.2.14 |
baseCurrentCallsCurrent calls.
The number of calls currently active on the MegaPAC.ro Counter .1.3.6.1.4.1.397.2.15 |
baseRetransmissionsNode Retransmissions.
The total number of frames which have been retransmitted
by the MegaPAC.ro Counter .1.3.6.1.4.1.397.2.16 |
baseRejectsNode Rejects.
The total number of frames that have been rejected by the
MegaPAC.ro Counter .1.3.6.1.4.1.397.2.17 |
baseTotalTransportCallsNode Total Transport calls.
The total number of transport calls established by the
MegaPAC.ro Counter .1.3.6.1.4.1.397.2.18 |
baseCurrentTransportCallsCurrent Transport Calls.
The number of transport calls currently active on the
MegaPAC.ro Counter .1.3.6.1.4.1.397.2.19 |
baseRunStatusNode Run Status.
This parameter indicates whether the operating system has
been 'Booted' from RAM (TELELOAD) or EPROM (default).ro Enumeration .1.3.6.1.4.1.397.2.20 |
baseReportsNode Reporting channel.
The name of the logical resource (channel) that the system
reports will be directed to.rw DisplayString .1.3.6.1.4.1.397.2.21 |
baseSessionStatisticsNode Session Statistics reporting channel.
The name of the logical resource (channel) that the system
session statistics will be directed to.rw DisplayString .1.3.6.1.4.1.397.2.22 |
baseBufferThresholdNode Buffer Threshold.
The threshold before flow control is invokedrw INTEGER .1.3.6.1.4.1.397.2.23 |
baseInitialPresentationTimerNode Initial Presentation Timer.
The maximum time allowed between initial connection to the
presentation service and the user entering a valid resource.
The call will be disconnected if this timer elapses.rw INTEGER .1.3.6.1.4.1.397.2.24 |
baseSecondaryPresentationTimerNode Secondary Presentation Timer.
After a call has been cleared by the Host DTE the user
has the option to use the presentation service to
establish another call, failure to do so within this time
period will result in the initial call being cleared.rw INTEGER .1.3.6.1.4.1.397.2.25 |
baseInactivityDetectTimerNode Inactivity Timer.
This timer will cause calls to be cleared if the IDLE option
has been configured on the channel.rw INTEGER .1.3.6.1.4.1.397.2.26 |
baseSegmentAccountingNode Segment Accounting.
This parameter causes the frames in/out parameters to
be displayed in terms of 64 byte SEGMENTS rather than frames.rw Enumeration .1.3.6.1.4.1.397.2.27 |
baseTerminalEmulationBuffersTerminal Emulation Buffers.
The number of system buffers allocated for Terminal Emulation
purposes.rw INTEGER .1.3.6.1.4.1.397.2.28 |
baseTransportBuffersTransport Buffers.
The number of transport buffers allocated for TP 0,2,3,4
sessions.rw INTEGER .1.3.6.1.4.1.397.2.29 |
baseCountrySettingsCountry Setting.
Invokes the ASCII representation of the Japanese
character set.rw Enumeration .1.3.6.1.4.1.397.2.30 |
baseTeleloadEnabledTeleload enable.
If set to yes the MegaPAC software may be downloaded by
ASCII file transfer.rw Enumeration .1.3.6.1.4.1.397.2.31 |
baseDefaultToPromCompatibleCold Boot From PROM.
If set to yes the MegaPAC software may be downloaded by
ASCII file transfer.rw Enumeration .1.3.6.1.4.1.397.2.32 |
baseCommandAllows SNMP manager to execute commands.rw Enumeration .1.3.6.1.4.1.397.2.33 |
baseCommandControllerIndexSets controller index for baseCommands where relevant.rw INTEGER .1.3.6.1.4.1.397.2.34 |
baseCommandChannelndexSets channel index for baseCommands where relevant.rw INTEGER .1.3.6.1.4.1.397.2.35 |
baseConnectedToProtocolIndicates the VCP state. NULL is VCP free; a returned value indicates BUSY and maps the access protocol.ro Enumeration .1.3.6.1.4.1.397.2.36 |
baseBillingThresholdSets threshold for billing alarms - entry written to ELOG file, and trap sent.rw INTEGER .1.3.6.1.4.1.397.2.37 |
baseBillUnreadNumber of BILLING records outstanding - to be read by SNMP manager.ro INTEGER .1.3.6.1.4.1.397.2.38 |
baseCurrentBillRecord number of current available BILLING record.ro INTEGER .1.3.6.1.4.1.397.2.39 |
baseBillRecordBufferThe current BILLING record data.ro DisplayString .1.3.6.1.4.1.397.2.40 |
baseCurrentConfigA decimal number from 0000 to 9999 representing the current configuration.ro INTEGER .1.3.6.1.4.1.397.2.41 |
baseCommandBufferThe VCP single line command string buffer.rw DisplayString .1.3.6.1.4.1.397.2.44 |
baseCommandLengthThe length in Hex of the single line command string.rw INTEGER .1.3.6.1.4.1.397.2.45 |
baseEMPresentIndicator of whether Environmental Monitor is present.ro Enumeration .1.3.6.1.4.1.397.2.46 |
baseEMTempTensTens part of Environmental Monitor temperature.ro INTEGER .1.3.6.1.4.1.397.2.47 |
baseEMTempUnitsUnit part of Environmental Monitor temperature.ro INTEGER .1.3.6.1.4.1.397.2.48 |
baseEMFan1Environmental Monitor Fan 1 state.ro Enumeration .1.3.6.1.4.1.397.2.49 |
baseEMFan2Environmental Monitor Fan 2 state.ro Enumeration .1.3.6.1.4.1.397.2.50 |
baseEMFan3Environmental Monitor Fan 3 state.ro Enumeration .1.3.6.1.4.1.397.2.51 |
baseEMVoltageEnvironmental Monitor voltage.ro DisplayString .1.3.6.1.4.1.397.2.52 |
baseEMPsu1Environmental Monitor PSU 1 state.ro Enumeration .1.3.6.1.4.1.397.2.53 |
baseEMPsu2Environmental Monitor PSU 2 state.ro Enumeration .1.3.6.1.4.1.397.2.54 |
baseCPUUtilCPU utilisation in the range 0 to 100.ro INTEGER .1.3.6.1.4.1.397.2.55 |
controller OBJECT IDENTIFIER .1.3.6.1.4.1.397.3 |
ctrlNumberConfiguredTotal Number of Controllers Configured.
The number of controllers in the MegaPAC which have been
configured.ro INTEGER .1.3.6.1.4.1.397.3.1 |
ctrlTotalNumberTotal Number of Controllers.
The TOTAL number of controllers in the MegaPAC including
unconfigured (NULL) controllers.ro INTEGER .1.3.6.1.4.1.397.3.2 |
ctrlStatTable SEQUENCE OF CtrlStatEntry .1.3.6.1.4.1.397.3.3 |
ctrlStatEntry CtrlStatEntry .1.3.6.1.4.1.397.3.3.1 |
ctrlStatIndexController index.
The position of this controller in relation to 'BASE'.
i.e. BASE = 0
NMSC = 1
PS01 = 2
...ro INTEGER .1.3.6.1.4.1.397.3.3.1.1 |
ctrlStatNameController name.
The unique 4 character name by which this controller is
known.ro DisplayString .1.3.6.1.4.1.397.3.3.1.2 |
ctrlStatTypeController Type.
The type of software controller.ro Enumeration .1.3.6.1.4.1.397.3.3.1.3 |
ctrlStatSubTypeSub Type.
The serial I/O board installed.ro Enumeration .1.3.6.1.4.1.397.3.3.1.4 |
ctrlStatNumberChannelsChannel Count.
The number of channels assigned to a controller.ro INTEGER .1.3.6.1.4.1.397.3.3.1.5 |
ctrlStatFirstChannelIndexFirst Channnel.
The 1st channel index number used by the controller
: PPP, X.25, XFRM, NFRM VFRM, CONS, IP, TIP, IPX, TIPX,
ESIS, DLC, LAN, TLAN, ILAN, XLAN SDLC, TERM, QLLC & HDLCro INTEGER .1.3.6.1.4.1.397.3.3.1.6 |
ctrlStatCRCErrorsCRC Errors.
The number of packets received for which the checksum
was not valid.ro Counter .1.3.6.1.4.1.397.3.3.1.7 |
ctrlStatTotalCallSetUpsTotal Call Set ups.
The total number of successful calls established on this
link.ro Counter .1.3.6.1.4.1.397.3.3.1.8 |
ctrlStatCurrentCallsCurrent Calls.
The number of calls currently active on this link.ro INTEGER .1.3.6.1.4.1.397.3.3.1.9 |
ctrlStatDataInData bytes In.ro Counter .1.3.6.1.4.1.397.3.3.1.10 |
ctrlStatDataOutData Out.
The total number of data bytes transmitted on this link.ro Counter .1.3.6.1.4.1.397.3.3.1.11 |
ctrlStatDataFramesInData Frames In.
The total number of data frames received on this link.ro Counter .1.3.6.1.4.1.397.3.3.1.12 |
ctrlStatDataFramesOutData Frames Out.
The total number of data frames transmitted on this
link.ro Counter .1.3.6.1.4.1.397.3.3.1.13 |
ctrlStatDataFrameRateInData Frame Rate In.
The rate that frames are arriving on this link,
specified in frames per second.ro INTEGER .1.3.6.1.4.1.397.3.3.1.14 |
ctrlStatDataFrameRateOutData Frame Frate Out.
The rate that frames are being transmitted on this link,
specified in frames per second.ro INTEGER .1.3.6.1.4.1.397.3.3.1.15 |
ctrlStatCallsReceivedCalls Received.
The total number of incoming call requests seen on this
link.ro Counter .1.3.6.1.4.1.397.3.3.1.16 |
ctrlStatCallsSentCalls Sent.
The total number of call requests sent out on this link.ro Counter .1.3.6.1.4.1.397.3.3.1.17 |
ctrlStatClearsReceivedClears Received.
The total number of call clear requests received on this
link.ro Counter .1.3.6.1.4.1.397.3.3.1.18 |
ctrlStatRetransmissionsRetransmissions.
The number of packets that have been transmitted more
than once on this link.ro Counter .1.3.6.1.4.1.397.3.3.1.19 |
ctrlStatRejectsRejects.
The total number of packets which have been rejected on
this link.ro Counter .1.3.6.1.4.1.397.3.3.1.20 |
ctrlStatStateState.
The level 2 data state of the link.ro Enumeration .1.3.6.1.4.1.397.3.3.1.21 |
ctrlStatSubStateSub State.
The level 3 state of this link.ro Enumeration .1.3.6.1.4.1.397.3.3.1.22 |
ctrlStatNoTriesTries.
The number of un-numbered control frames sent to try and
establish the link.ro Counter .1.3.6.1.4.1.397.3.3.1.23 |
ctrlStatOptionsOptions
The options currently configured for this link. Note, that
the values returned by the MegaPAC may be additive
values - representing combined combinations for the
table listed e.g. poll+ext.ro Enumeration .1.3.6.1.4.1.397.3.3.1.24 |
ctrlStatLCGNLCGN
The logical channel group number for this link.ro INTEGER .1.3.6.1.4.1.397.3.3.1.25 |
ctrlStatResetsReceivedResets Received.
The total number of reset packets received on this link.ro Counter .1.3.6.1.4.1.397.3.3.1.26 |
ctrlStatInterruptsReceivedInterupts Received.
The total number of interrupt packets received on this
link.ro Counter .1.3.6.1.4.1.397.3.3.1.27 |
ctrlStatOuputQueueLengthOutput Queue Length.
The number of packets queued for transmission on this
link.ro INTEGER .1.3.6.1.4.1.397.3.3.1.28 |
ctrlStatStationAddressLocal MAC Address
The MAC Address of the MegaPAC.ro DisplayString .1.3.6.1.4.1.397.3.3.1.29 |
ctrlStatDestinationAddressDestination MAC Address.
The MAC Address of the destination device.ro DisplayString .1.3.6.1.4.1.397.3.3.1.30 |
ctrlStatEIAEIA state.
Displays the EIA signals currently on the link.ro DisplayString .1.3.6.1.4.1.397.3.3.1.31 |
ctrlStatSdlcOptionsSDLC Options.
A range of link level options used for establishing
IBM connections.ro Enumeration .1.3.6.1.4.1.397.3.3.1.32 |
ctrlStatArpRequestRecARP Requests Received.
The number of ARP requests sent to the MegaPACro INTEGER .1.3.6.1.4.1.397.3.3.1.33 |
ctrlStatArpRequestSentARP Requests Sent.
The number of ARP requests processed to the local LAN
by the MegaPACro INTEGER .1.3.6.1.4.1.397.3.3.1.34 |
ctrlStatArpResponsesRecARP Respones Received.
The number of ARP responses returned to the
the MegaPACro INTEGER .1.3.6.1.4.1.397.3.3.1.35 |
ctrlStatTestTypeAllows SNMP manager to set V54 tests; local or remote or off.rw Enumeration .1.3.6.1.4.1.397.3.3.1.36 |
ctrlStatTestSetAllows SNMP manager to apply the local/remote V54 test selection.rw Enumeration .1.3.6.1.4.1.397.3.3.1.37 |
ctrlStatTestAllows SNMP manager to activate local/remote V54 test.rw Enumeration .1.3.6.1.4.1.397.3.3.1.38 |
ctrlStatLstateAllows SNMP manager to read Local Loop test result.rw Enumeration .1.3.6.1.4.1.397.3.3.1.39 |
ctrlStatRstateAllows SNMP manager to read Remote Loop test result.rw Enumeration .1.3.6.1.4.1.397.3.3.1.40 |
ctrlParamTableThe controller configuration table. SEQUENCE OF CtrlParamEntry .1.3.6.1.4.1.397.3.4 |
ctrlParamEntryAn individual controller configuration. CtrlParamEntry .1.3.6.1.4.1.397.3.4.1 |
ctrlParamIndexIndex
The position of this controller in relation to 'BASE'.
i.e. BASE = 0
NMSC = 1
PS01 = 2
...ro INTEGER .1.3.6.1.4.1.397.3.4.1.1 |
ctrlParamNameName.
The unique 4 character name by which this controller is
known.rw DisplayString .1.3.6.1.4.1.397.3.4.1.2 |
ctrlParamTypeType.
The type of controllerrw Enumeration .1.3.6.1.4.1.397.3.4.1.3 |
ctrlParamSubTypeSub-Type.
The link between the controller and its associated hardware
type.rw Enumeration .1.3.6.1.4.1.397.3.4.1.4 |
ctrlParamNoChannelsNumber of channels.
The number of logical channels configured on the controller.rw INTEGER .1.3.6.1.4.1.397.3.4.1.5 |
ctrlParamSpeedSpeed.
The clock speed of the interface.rw Enumeration .1.3.6.1.4.1.397.3.4.1.6 |
ctrlParamInterfaceTypeThe serial interface type. Note, Only applicable to MegaCard.rw Enumeration .1.3.6.1.4.1.397.3.4.1.7 |
ctrlParamPacketSizePacket Size.
The maximum packet size in bytes of outgoing packets,
this parameter must be less than or equal to the 'BASE'
statistic 'maxPacketSize'.rw Enumeration .1.3.6.1.4.1.397.3.4.1.8 |
ctrlParamV54ModemV54 Modem.
Enable V54 loop back testing. Note this does not initiate
loop back testing, the loop back is initiated by typing
in the 'TEST' command.rw Enumeration .1.3.6.1.4.1.397.3.4.1.9 |
ctrlParamAddressAddress.
The logical address designation of the controller.rw Enumeration .1.3.6.1.4.1.397.3.4.1.10 |
ctrlParamOptionsOptions.
A range of controller options, options may be specified
individually or added together.rw Enumeration .1.3.6.1.4.1.397.3.4.1.11 |
ctrlParamInitFrameInitial Frame.rw Enumeration .1.3.6.1.4.1.397.3.4.1.12 |
ctrlParamT1T1.
Timer for retransmission of unacknowleged frames. Specified
in 0.1 second units.rw INTEGER .1.3.6.1.4.1.397.3.4.1.13 |
ctrlParamTriesTries.
The number of times a frame will be retransmitted before
a link restart is initiated.rw INTEGER .1.3.6.1.4.1.397.3.4.1.14 |
ctrlParamKLevel2KLevel 2.
The level 2 window size.rw INTEGER .1.3.6.1.4.1.397.3.4.1.15 |
ctrlParamKLevel3KLevel 3.
The level 3 window size.rw INTEGER .1.3.6.1.4.1.397.3.4.1.16 |
ctrlParamLineGroupLine Group.
The line group is used for load sharing. If two links
have same (non-zero) line group then data may be shared
between them.rw INTEGER .1.3.6.1.4.1.397.3.4.1.17 |
ctrlParamLCGNLCGN.
The logical channel group number for this link.rw INTEGER .1.3.6.1.4.1.397.3.4.1.18 |
ctrlParamLCNOffsetLCN Offset.
This parameter is used in conjunction with the LCGN. It's
purpose is to shift the channel range by the appropriate
offset.rw INTEGER .1.3.6.1.4.1.397.3.4.1.19 |
ctrlParamAddressGroupAddress Group.
This parameter is used in conjunction with the address
group field in the x25 file to provide different addressing
domains.rw INTEGER .1.3.6.1.4.1.397.3.4.1.20 |
ctrlParamFrameSequenceFrame Sequence.
This parameter determines if normal or extended frame
sequencing is supported.rw Enumeration .1.3.6.1.4.1.397.3.4.1.21 |
ctrlParamCallTimeOutCall Time Out.
The time in seconds the MegaPAC will wait to receive a call
accept packet before clearing the call.rw INTEGER .1.3.6.1.4.1.397.3.4.1.22 |
ctrlParamErrorThresholdError Threshold.
The number of CRC errors that will be accepted before
generating an error report.rw INTEGER .1.3.6.1.4.1.397.3.4.1.23 |
ctrlParamLoopBarPriorityLoop Bar Priority.
Prevents calls from looping on the same controller.rw INTEGER .1.3.6.1.4.1.397.3.4.1.24 |
ctrlParamExtendedCallMgmtExtended Call Management.
Invokes extended packet processing facilities
via the MAC file.rw Enumeration .1.3.6.1.4.1.397.3.4.1.25 |
ctrlParamOptionalTimersOptional Timers.
Optional level 3 timers for clearing calls when a clear
confirmation has not been received after a clear request has
been sent. T13 is used if the controller is set to be a
logical DCE and the timeout will be 60 seconds. T23 is used
if the controller is a logical DTE and the timeout is 180
seconds.rw Enumeration .1.3.6.1.4.1.397.3.4.1.26 |
ctrlParamOptionalFlagsOptional Flags.
This parameter is used to insert extra flags between frames
to slow down the rate of transmission. It will only take
effect on controllers with a sub-type of XIO.rw INTEGER .1.3.6.1.4.1.397.3.4.1.27 |
ctrlParamTransportLevelTypeTransport Level Type.
Enable the ISO transport facility.rw Enumeration .1.3.6.1.4.1.397.3.4.1.28 |
ctrlParamTransportClassTransport Class.
The type of transport class implemented.rw Enumeration .1.3.6.1.4.1.397.3.4.1.29 |
ctrlParamDefaultWindowSizeDefault Window Size.
The initial credit limit to be used on a transport
session.rw INTEGER .1.3.6.1.4.1.397.3.4.1.30 |
ctrlParamDisableFlowControlDisable Flow Control.
Enable/disable flow control on a tranport class 2 call.rw Enumeration .1.3.6.1.4.1.397.3.4.1.31 |
ctrlParamTSAPFormatTSAP Format.
Determines how the TSAP's will be treated internally by the
MegaPAC. If set to text the local and remote TSAP's will be
converted to form a 4 character internal resource name. If
set to hex the first two hexadecimal pairs will form the
resource name.rw Enumeration .1.3.6.1.4.1.397.3.4.1.32 |
ctrlParamMaximumTPDUSizeMax. TPDU Size.
The maximum Transport Protocol Data Unit Size.rw Enumeration .1.3.6.1.4.1.397.3.4.1.33 |
ctrlParamTTRTimeTTR Timer.
Time To Resynchronise. Specifies the time delay in seconds
for the transport class three timer to resync at the initiating
end.rw INTEGER .1.3.6.1.4.1.397.3.4.1.34 |
ctrlParamTWRTimeTWR Timer.
Time to Wait for Resynchronisation. The time delay in seconds
allowed for the transport class 3 timer at the responding end
to wait for resynchronisation, before clearing down the
transport session.rw INTEGER .1.3.6.1.4.1.397.3.4.1.35 |
ctrlParamDestinationAddressDestination Address.
The physical address of the target device.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.397.3.4.1.36 |
ctrlParamDSAPDSAP.
The Destination Service Access Point.rw INTEGER .1.3.6.1.4.1.397.3.4.1.37 |
ctrlParamSSAPSSAP.
The Source Service Access Point.rw INTEGER .1.3.6.1.4.1.397.3.4.1.38 |
ctrlParamSDLCOptionsSDLC Options.
A range of link level options used for establishing
IBM connections.rw Enumeration .1.3.6.1.4.1.397.3.4.1.39 |
ctrlParamPrimaryStationPrimary Station.
This parameter determines whether the MegaPAC will operate
as a HOST primary connection (yes) or a CLUSTER secondary
connection (no).rw Enumeration .1.3.6.1.4.1.397.3.4.1.40 |
ctrlParamIdleDetectTimeIdle Detect Timer.
This parameter determines the time period in tenths
of a second before an unacknowleged POLL/RESPONSE frame
will be retransmitted.rw INTEGER .1.3.6.1.4.1.397.3.4.1.41 |
ctrlParamPollIntervalPoll Interval.
The time period in tenths of a second between sending
POLL frames.rw INTEGER .1.3.6.1.4.1.397.3.4.1.42 |
ctrlParamDuplexDuplex.
Enables SDLC full duplex operation, half duplex operation
is reserved for future use.rw Enumeration .1.3.6.1.4.1.397.3.4.1.43 |
ctrlParamTransmitDelayTransmit Delay.
Determines the time period in tenths of a second between
the MegaPAC receiving an RR frame with the P-Bit set and the
MegaPAC issuing an RR response with the F-Bit set.rw INTEGER .1.3.6.1.4.1.397.3.4.1.44 |
ctrlParamSlowPollTimerSlow Poll Timer.
When the controller has been defined as a primary station
a slow poll rate can be specified for polling a Cluster
controller that is down. This is to avoid causing delays to
working Cluster controllers in a multi-point mode. The value
is specified in tenths of a second.rw INTEGER .1.3.6.1.4.1.397.3.4.1.45 |
ctrlParamMaxCallIntervalMax. Call Interval.
When controller is configured as a primary station, a call
request retry interval may be defined, so as to avoid the
situation where successive call requests are continuously
generated to the network. The initial call interval is 2
seconds, this interval is progressively doubled until the
Maximum Call Interval (defined in minutes) is reached.rw INTEGER .1.3.6.1.4.1.397.3.4.1.46 |
ctrlParamMaxCallCyclesMax. Call Cycles.
This parameter is used in conjunction with the Maximum
Call Interval parameter. It specifies the maximum number of
call request cycles that can take effect before call requests
continue at the Maximum Call Interval parameter setting. Each
cycle consisting of call requests being initiated at intervals
in incrementing multiples of two seconds, up to the Maximum Call
Interval parameter.rw INTEGER .1.3.6.1.4.1.397.3.4.1.47 |
ctrlParamGroupPollGroup Poll.
Used in SNA applications, where the specified value
would generate multiple down-stream poll requests.rw INTEGER .1.3.6.1.4.1.397.3.4.1.48 |
ctrlParamDelayToRTSLowDelay RTS Low.
Specifies the number of padding characters to be inserted
between the end of data transmission and the dropping of the
RTS signal. Only required for synchronous operation.rw INTEGER .1.3.6.1.4.1.397.3.4.1.49 |
ctrlParamDelayToCTSHighDelay CTS High.
Specifies the number of padding characters to be inserted
between the dropping of RTS and the raising of CTS. Only
required for synchronous operation.rw INTEGER .1.3.6.1.4.1.397.3.4.1.50 |
ctrlParamInputSyncDeletionInput Sync Deletion.
If set, all SYNC characters will be stripped prior to
transmission. Only effective in synchronous full duplex mode.rw Enumeration .1.3.6.1.4.1.397.3.4.1.51 |
ctrlParamOutputSyncInsertionOutput Sync Insertion.
Specifies the number of SYNC characters to be transmitted
prior to the start of the data block. Only effective in
synchronous operation.rw INTEGER .1.3.6.1.4.1.397.3.4.1.52 |
ctrlParamDCDFilterDCD Filter.
A filter delay specified in tenths of a second which
prevents unwanted link restarts caused by toggling of DCD
signal.rw INTEGER .1.3.6.1.4.1.397.3.4.1.53 |
ctrlParamInhibitTimeFillInhibit Time Fill
Allows the insertion of time fill frames to compensate
for network delays. Effective in synchronous mode only.rw Enumeration .1.3.6.1.4.1.397.3.4.1.54 |
ctrlParamDirectedBroadcastsDirected Broadcasts.rw Enumeration .1.3.6.1.4.1.397.3.4.1.55 |
ctrlParamDefaultLocalPrinterDefault Local Printer.
The number of the channel which is reserved for a Screen
Print server, a value of (0) disables the Screen Print facility.rw INTEGER .1.3.6.1.4.1.397.3.4.1.56 |
ctrlParamNewLANInterfaceNew FRM Port.
This controller marks the first position of a controller
connection to a LAN interface. All other controllers
defined as NewPhysicalInterface/ No will map to the same
interface defined as NewPhysicalInterface/ Yes.rw Enumeration .1.3.6.1.4.1.397.3.4.1.57 |
ctrlParamNewSerialInterfaceNew FRM Port.
This controller marks the first position of a controller
connection to a serial interface. All other controllers
defined as NewPhysicalInterface/ No will map to the same
interface defined as NewPhysicalInterface/ Yes.rw Enumeration .1.3.6.1.4.1.397.3.4.1.58 |
ctrlParamDlciDefines the DLCI PVC numberrw INTEGER .1.3.6.1.4.1.397.3.4.1.59 |
ctrlParamModeDefines a Network to Network Inteface (NNI) or
User Network Interface (UNI) implementation.
Where MegaPAC connects to a Frame Realy switch,
this parameter just be defined as DTE i.e. a UNI,
otherwise when connecting operating as a switch,
NNI i.e. DCE operation must be specified.
All controllers mapped to the same physical
interface must be configured the same mode settingrw Enumeration .1.3.6.1.4.1.397.3.4.1.60 |
ctrlParamLmiLocal Management Inteface (LMI).
Ansi = ANSI LMI
yes = T1.S1 LMI
no = LMI disabled.rw Enumeration .1.3.6.1.4.1.397.3.4.1.61 |
ctrlParamKeepAliveTimerOnly applicable if the LMI is active. Specifies in
seconds the interval between keep alive messages.
If this end is a DTE, this is the actual interval
between Status Requests generated to the DCE.
If this end is a DCE, then the timer is used simply
to detect whether connection to the DTE has been lost.
Note: it is the DTE which is the active partner across
the LMI interface, in accordance with the LMI
specification.rw INTEGER .1.3.6.1.4.1.397.3.4.1.62 |
ctrlParamStatusEnquiryIntervalFrame Relay :
Specifies how often a DTE sends a or a DCE expects a
Full Status Request message. The number specified is
the ratio between Status Requets messages, and Full Status
Request enquiries. For example, if the value 10 is specified,
and this end is a DTE, then every 10th status request would
include a full status request (in the above example every
100 seconds).rw INTEGER .1.3.6.1.4.1.397.3.4.1.63 |
ctrlParamBandwidthThe sample period used in enforcing the committed
information rate (CIR). The CIR expressed in terms of
characters per 1/10 th second. There are two further
parameters which appear directly after the BANDWIDTH/
prompt which are designed to handle bursty traffic
(i.e. Bc and Be).rw INTEGER .1.3.6.1.4.1.397.3.4.1.64 |
ctrlParamBurstCommitBurst Commit, i.e. the number of characters the
remote end is committed to buffering, in our case
in a 1/10th of a second periodrw INTEGER .1.3.6.1.4.1.397.3.4.1.65 |
ctrlParamBurstEligibilityBurst Eligibility, i.e the DLCI in question is
enabled to transmit a burst beyond its committed
information rate, when enabled to do so by the state
of the other DLCIs. The figure given is again with
respect to a 1/10th second period, and the maximum data
rate when the DLCI is enabled to transmit at its burst
rate is given by the equation ;
Maximum data rate = CIR(1+Be/Bc)
It should be noted that on DLCIs which are carrying data
of a non-bursty nature (e.g voice traffic), the Be should
be configured as zero (thereby telling the MegaPAC that it
is carrying traffic of a non-bursty nature.) Secondly, if
the Bc value is configured as zero, the MegaPAC uses a
default sample period of 1 second.rw INTEGER .1.3.6.1.4.1.397.3.4.1.66 |
channel OBJECT IDENTIFIER .1.3.6.1.4.1.397.4 |
chanNumberConfiguredNumber of channels.
The number of channels configured.ro INTEGER .1.3.6.1.4.1.397.4.1 |
chanStatTableA table of channels associated with a controller. SEQUENCE OF ChanStatEntry .1.3.6.1.4.1.397.4.2 |
chanStatEntryAn individual channel entry. ChanStatEntry .1.3.6.1.4.1.397.4.2.1 |
chanStatIndexIndex.
The position of this channel in the controller channel
Table.ro INTEGER .1.3.6.1.4.1.397.4.2.1.1 |
chanStatNameName.
A user defined name for routing calls to this channel.ro DisplayString .1.3.6.1.4.1.397.4.2.1.2 |
chanStatControllerIndexController Index.
The index to the controller that this channel operates within.ro INTEGER .1.3.6.1.4.1.397.4.2.1.3 |
chanStatNameCtrlNameController Name.
The controller NAME supporting this channelro DisplayString .1.3.6.1.4.1.397.4.2.1.4 |
chanStatConnectedToChannelIndexConnected to Index.
The INDEX of the CHANNEL that this channel is
connected to.ro INTEGER .1.3.6.1.4.1.397.4.2.1.5 |
chanStatStateState.
The current Status of the channel, the status may be
one or a combination of the following:
disc Disconnected.
emul Channel in Terminal Emulation mode.
emul Channel in Terminal Emulation mode.
post Processing data before forwarding e.g. LF insert in async.
busy Temporarily unavailable.
call Outgoing channel making call.
data Data transfer, call in progress.
wake Outgoing channel transmitting.
setup Incoming channel waiting outgoing channel call setup.
rout Incoming channel waiting assignment of outgoing channel.
addr Incoming channel waiting resource selection.
name Incoming channel is processing a users password.
look Incoming channel is looking-up a users password name.
serv Service selection mode awaiting resource code NAME.
pass Incoming channel is processing a users password.
rung Ring Indicator MUX PORT only.ro Enumeration .1.3.6.1.4.1.397.4.2.1.6 |
chanStatSessionStatusSession Status.
The Status of the channel during a call session, the
status may be one or a combination of the following:
State Description
CALL Call Originator.
DRI Flow controlling input.
DRO Flow controlling on output.
TRAN Presentation service not involved in call set-up.
QUEU Queued to selected resource.
STAT Awaiting queue status information.
PAD In PAD Recall mode.
DISC Data buffers draining before clearing call.ro Enumeration .1.3.6.1.4.1.397.4.2.1.7 |
chanStatEIAEIA
Displays the status of the V24/V28 signals on term or
muxport links, or call status on X.25 links. The down
state indicates that level 2 is inactive.ro Enumeration .1.3.6.1.4.1.397.4.2.1.8 |
chanStatTotalFramesInTotal Frames In.
The total number of frames received on this channel
since it entered Data State.ro Counter .1.3.6.1.4.1.397.4.2.1.9 |
chanStatTotalFramesOutTotal Frames out.
The total number of frames transmitted on this channel
since it entered Data State.ro Counter .1.3.6.1.4.1.397.4.2.1.10 |
chanStatTotalCharsInTotal Characters In.
The total number of characters received on this channel
since it entered Data State.ro Counter .1.3.6.1.4.1.397.4.2.1.11 |
chanStatTotalCharsOutTotal Characters Out.
The total number of characters transmitted on this
channel since it entered Data State.ro Counter .1.3.6.1.4.1.397.4.2.1.12 |
chanStatTxWindowTx Window.
The Level 3 Transmit Window size.ro INTEGER .1.3.6.1.4.1.397.4.2.1.13 |
chanStatRxWindowRx Window.
The Level 3 Receive Window size.ro INTEGER .1.3.6.1.4.1.397.4.2.1.14 |
chanStatTxSizeTx Size.
The maximum size for outgoing packets.ro INTEGER .1.3.6.1.4.1.397.4.2.1.15 |
chanStatRxSizeRx Size.
The maximum acceptable size for incoming packets.ro INTEGER .1.3.6.1.4.1.397.4.2.1.16 |
chanStatCauseCause.
The value of the cause code in the last Clear Packet
received or transmitted (decimal).ro INTEGER .1.3.6.1.4.1.397.4.2.1.17 |
chanStatDiagnosticDiagnostic.
The value of the diagnostic code in the last Clear
Packet received or transmitted (decimal).ro INTEGER .1.3.6.1.4.1.397.4.2.1.18 |
chanStatResetCauseReset Cause.
The value of the last reset code in the last RESET
packet transmitted.ro INTEGER .1.3.6.1.4.1.397.4.2.1.19 |
chanStatResetDiagnosticReset Diagnostic.
The value of the last diagnostic code in the last RESET
packet transmitted.ro INTEGER .1.3.6.1.4.1.397.4.2.1.20 |
chanStatResetCauseReceivedReset Cause Received.
The value of the last reset code in the last RESET
packet received.ro INTEGER .1.3.6.1.4.1.397.4.2.1.21 |
chanStatResetDiagReceivedReset Diagnostic Received.
The value of the last diagnostic code in the last RESET
packet received.ro INTEGER .1.3.6.1.4.1.397.4.2.1.22 |
chanStatLevel3StateLevel 3 State.
The level 3 status of the channel.ro Enumeration .1.3.6.1.4.1.397.4.2.1.23 |
chanStatCallPriorityCall Priority.
Call and Resource priorities are used primarily for
providing alternate routing. For a call to succeed the
Call Priority on the incoming channel must be greater
than or equal to the Resource Priority on the outgoing
channel.ro INTEGER .1.3.6.1.4.1.397.4.2.1.24 |
chanStatResourcePriorityResource Priority
See chanCallPriority above.ro INTEGER .1.3.6.1.4.1.397.4.2.1.25 |
chanStatPadEnablePAD Enable.
The value of this statistic reflects the setting as
configured on the channel.ro Enumeration .1.3.6.1.4.1.397.4.2.1.26 |
chanStatPortMatchPort Match.
The TCP port that is connectedro Enumeration .1.3.6.1.4.1.397.4.2.1.27 |
chanStatPrimaryStationPrimary Station.
Determines whether the MegaPAC port is functioning as a
Primary or Secondary SDLC station.ro Enumeration .1.3.6.1.4.1.397.4.2.1.28 |
chanStatSDLCStateSDLC State.
The State of the SDLC connection, may be one of the
following:
State Description
ACTIVE The SNRM and UA commands have been sent
successfully. If primary, the P-Bit has
not been sent (i.e. has not been
polled). If secondary, the P-Bit has
not been received (has got F-Bit and
not been polled again).
DISC Primary station only. Either a 'STOP'
command has been issued for the port,
or a QDISC command has been received
from the network.
The MegaPAC will be sending an SDLC
DISC command with the P-Bit set.
POLL If primary, the MegaPAC has sent a
frame with the P-Bit (has polled). If
secondary, the MegaPAC has received the
P-Bit (has been polled).
SNRM Only for primary stations. The MegaPAC
has sent a SNRM, but has not received a
UA.ro Enumeration .1.3.6.1.4.1.397.4.2.1.29 |
chanStatQLLCStateQLLC State.
The State of the QLLC connection, may be one of the
following:
State Description
CLSD The MegaPAC has received a QDISC and
sent a QUA on the network. This sets
the DISC state on the SDLC port.
CLSI The MegaPAC has sent a QDISC and is
waiting for a QUA.
FRMR The MegaPAC has received a QFRMR from
the network.
INOP The SVC is down.
OPEN The VC is running. QSM and QUA have
been sent and received.
OPNI The MegaPAC has sent a QSM and is
awaiting a QUA.ro Enumeration .1.3.6.1.4.1.397.4.2.1.30 |
chanStatSDLCTransmitStateSDLC Transmit State.
May be one of the following:
State Description
NORM The MegaPAC is allowed to transmit data.
NULL The MegaPAC is not allowed to transmit data.
RNR The MegaPAC has received an RNR.
RTRY The MegaPAC is in the retransmission state.ro Enumeration .1.3.6.1.4.1.397.4.2.1.31 |
chanStatPollsPolls.
The quantity of polls that have occured since the link
was establishedro INTEGER .1.3.6.1.4.1.397.4.2.1.32 |
chanStatStationAddressStation Address.
The IBM PU poll addressro INTEGER .1.3.6.1.4.1.397.4.2.1.33 |
chanStatXIDIdentificationXID Identification.
This field contains the first 64 bytes of the XID
that has been used.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.397.4.2.1.34 |
chanStatTriesTries.
The number of times the current command has been
transmitted.ro INTEGER .1.3.6.1.4.1.397.4.2.1.35 |
chanStatWindowKLevel 2.
The level 2 window size.ro INTEGER .1.3.6.1.4.1.397.4.2.1.36 |
chanStatLUActiveLU Active.
If set to YES then the MegaPAC Logical Unit has
responded positively to an ACTLU command. If set to NO
the MegaPAC has either not received or has responded
negatively to an ACTLU command.ro Enumeration .1.3.6.1.4.1.397.4.2.1.37 |
chanStatBindActiveBind Active.
If set to YES then the MegaPAC Logical Unit has
responded positively to a BIND command. If set to NO the
MegaPAC has either not received or has responded
negatively to a BIND command.ro Enumeration .1.3.6.1.4.1.397.4.2.1.38 |
chanStatLUTypeLU Type.
The Session type taken from the BIND command. It
may be one of the following:
Session Type Description
0 User defined applications.
1 Printer.
2 Full Screen 3270 applications.
3 Older type printers.ro INTEGER .1.3.6.1.4.1.397.4.2.1.39 |
chanStatBreaksReceivedBreaks Rx
The number of Break characters received from the
terminal.ro Counter .1.3.6.1.4.1.397.4.2.1.40 |
chanStatFramingErrorsFraming Errors.
The number of characters received with no stop bit
appended. The MegaPAC substitutes a '#' character in
place of each framing error.ro Counter .1.3.6.1.4.1.397.4.2.1.41 |
chanStatInputOverrunsInput Overruns.
The number of times that data has been discarded due
to a lack of receive buffers.ro Counter .1.3.6.1.4.1.397.4.2.1.42 |
chanStatParityErrorsTParity Errors.
he number of parity errors received on this
channel.ro Counter .1.3.6.1.4.1.397.4.2.1.43 |
chanStatTerminalTypeTerminal Type.
The type of emulation to be applied to the TERM
controller, it may be one or more of the following:
Type comment
ASYN ASCII data support
SYNC Bi-sync data support
MINI Minitel terminal support
HP H.P ENQ / ACK async protocol support
X28 X28 command syntax (English)
X28F X28 command syntax (French)
ANSI Async ASCII Terminal support
VPAD Viewdata PAD Emulation support
MTRM MegaTerm PC Emulation support
BUF Used for Buffer PVC call set-ups
TPAD ACAB30 transaction card terminal support
VT22 Async VT220Terminal supportro Enumeration .1.3.6.1.4.1.397.4.2.1.44 |
chanStatCircuitTypeCircuit Type.
The type of circuit used on this channel, it may be
one or more of the following:ro Enumeration .1.3.6.1.4.1.397.4.2.1.45 |
chanStatOptionsThe option(s) which have been envoked on this
channel, one or more of:ro Enumeration .1.3.6.1.4.1.397.4.2.1.46 |
chanStatBuffersBuffers.
The number of data buffers to be used as a threshold
value before flow control to the terminal is invoked.ro INTEGER .1.3.6.1.4.1.397.4.2.1.47 |
chanStatDiscModeDisc mode.
Specifies the call disconnect character that may be
applied having established a route via the
presentation service.ro INTEGER .1.3.6.1.4.1.397.4.2.1.48 |
chanStatMenuNumberMenu Number.
Specifies which menu will be displayed to the user
by the presentation service.ro INTEGER .1.3.6.1.4.1.397.4.2.1.49 |
chanStatHelpNumberHelp Number.
Specifies which help menu will be displayed to the
user by the presentation service.ro INTEGER .1.3.6.1.4.1.397.4.2.1.50 |
chanStatNewsNumberNews Number.
The Menu number that will be displayed if an
outgoing resource is unavailable.ro INTEGER .1.3.6.1.4.1.397.4.2.1.51 |
chanStatPadRecallPad Recall.
This parameter allows the user to escape from the
data transfer state to the PAD command state. The
permitted values are:
0 No PAD recall
1 Escape character is ^P
2 - 126 The decimal value specified is the escape
characterro INTEGER .1.3.6.1.4.1.397.4.2.1.52 |
chanStatEchoEcho.
Determines whether 'echo' is enabled or disabled. If
set to controlled, the echo facility is controlled by
the operator.ro Enumeration .1.3.6.1.4.1.397.4.2.1.53 |
chanStatDataForwardingData Forwarding.
This parameter controls which character or
characters cause the accumulated data to be
forwarded. The possible values may be added together
to forward on one of a number of conditions. The
allowable values are:
0 Forward only on buffer full.
128 Forward on graphics characters.
64 Forward on all characters in columns 0 and 1
of the International Alphabet No. 5.
1 Forward on A-Z, a-z and 0-9.
2 Forward on Carriage Return.
4 Forward on ESC, BEL, ENQ, ACK.
8 Forward on DEL, CAN, DC2.
16 Forward on EXT, EOT.
32 Forward on HT, LF, VT, FF.ro INTEGER .1.3.6.1.4.1.397.4.2.1.54 |
chanStatDelayDelay.
Specifies the idle time in tenths of a second,
allowable between successive characters before the
accumulated data is forwarded. A value of 0 disables
the timeout facility.ro INTEGER .1.3.6.1.4.1.397.4.2.1.55 |
chanStatDRIDRI.
Flow control of terminal by the MegaPAC. Valid
settings are:
enabled MegaPAC flow controls terminal using
XON/XOFF.
cts MegaPAC flow controls terminal using
CTS.
init+enable MegaPAC sends XON automatically on
initialisation.
disable No flow control.ro Enumeration .1.3.6.1.4.1.397.4.2.1.56 |
chanStatPadSignalsPad Signals.
Enable X.28 prompts and/or messages to be displayed
on the users terminal.ro Enumeration .1.3.6.1.4.1.397.4.2.1.57 |
chanStatBreakBreak.
The Action the MegaPAC will take on receipt of a
Break Signal. The valid values are:
0 When the MegaPAC receives a Break Signal from
the terminal no action is taken.
1 When the MegaPAC receives a Break Signal from
the terminal it will transmit an INTERRUPT
packet.
2 When the MegaPAC receives a Break Signal from
the terminal it will transmit an RESET
packet.
5 When the MegaPAC receives a Break Signal from
the terminal it will transmit an INTERRUPT
packet and an indication of Break PAD
message.
8 When the MegaPAC receives a Break Signal from
the terminal it will escape from data
transfer state.
21 When the MegaPAC receives a Break Signal from
the terminal it will transmit an INTERRUPT
packet and an indication of Break PAD
message, while setting (X3) parameter (8)
to the value 1 (discard any data
received from the network).ro INTEGER .1.3.6.1.4.1.397.4.2.1.58 |
chanStatPaddingPadding.
The number of NULL characters inserted after a
carriage return.ro INTEGER .1.3.6.1.4.1.397.4.2.1.59 |
chanStatFoldFold
The number of characters output before line folding
occurs. Setting to 0 disables line folding.ro INTEGER .1.3.6.1.4.1.397.4.2.1.60 |
chanStatDROData Restraint Out.ro Enumeration .1.3.6.1.4.1.397.4.2.1.61 |
chanStatLFILFI.
This parameter controls linefeed insertion after a
carriage return. The valid seetings are:
0 Line feed insertion disabled.
1 A linefeed is inserted after a carriage
return, in the data forwarded to the
terminal.
4 A linefeed is sent to the terminal after echo
of a carriage return to the terminal.
5 As defined by values 1 + 4.
6 Linefeed inserted after carriage return from
terminal and each carriage return echoed to
the terminal.
7 As defined by values 1 + 6.ro INTEGER .1.3.6.1.4.1.397.4.2.1.62 |
chanStatLFPadLFPad.
The number of NULL padding characters sent to a
device following a linefeed character.ro INTEGER .1.3.6.1.4.1.397.4.2.1.63 |
chanStatEditEdit.
Controls editing of text in data transfer state.ro Enumeration .1.3.6.1.4.1.397.4.2.1.64 |
chanStatCharDelChar Del.
The keystroke used for deleting a character.ro INTEGER .1.3.6.1.4.1.397.4.2.1.65 |
chanStatBufferDelBuffer Del.
The keystroke used for deleting the buffer.ro INTEGER .1.3.6.1.4.1.397.4.2.1.66 |
chanStatDispDisp
The keystroke used to redisplay the data in the
buffer.ro INTEGER .1.3.6.1.4.1.397.4.2.1.67 |
chanStatEditServiceSignalsEdit Service Signals.
This parameter enables the user to edit the PAD
service signals (echoing). The valid settings are:
0 No editing PAD service signals are echoed.
1 A '\' will be echoed for each character
deleted.
2 A 'BS' character will be echoed for each
character deleted.
8 and 32-126 Specifies the decimal value of the
ASCII character to be echoed for each
character deleted.ro INTEGER .1.3.6.1.4.1.397.4.2.1.68 |
chanStatEchoMaskEcho Mask.
This parameter controls the characters which should
not be echoed. The valid settings are:
0 All characters should be echoed to the
terminal.
1 do not echo carriage return.
2 do not echo linefeed.
4 do not echo VT, HT and FF characters.
8 do not echo BEL and BS character.
16 do not echo ESC and ENQ.
32 do not echo ACK, NAK, STX, SOH, EOT, ETB or
ETX.
64 do not echo editing characters as defined by
parameters 16, 17 and 18.
128 do not echo other control characters and DEL.ro INTEGER .1.3.6.1.4.1.397.4.2.1.69 |
chanStatParityTreatmentParity Treatment.
Determines the parity generation and checking
performed
valid settings are:
0 No parity generation or checking.
1 Check parity.
2 Generate parity.
3 Check and generate parity.ro INTEGER .1.3.6.1.4.1.397.4.2.1.70 |
chanStatPageWaitPageWait.
Specifies the number of lines to be transmitted,
after which the MegaPAC will wait until instructed by
the user to continue sending data (by entering <CTRL
>Q). A value of 0 disables the page wait facility.ro INTEGER .1.3.6.1.4.1.397.4.2.1.71 |
chanStatForceForward Char.
The ASCII character which will force data
forwarding, 0 disables forced data forwarding.ro INTEGER .1.3.6.1.4.1.397.4.2.1.72 |
chanStatBreakCharBreak Char.
The ASCII character in decimal which is used to
simulate a BREAK signal.ro INTEGER .1.3.6.1.4.1.397.4.2.1.73 |
chanStatNetworkParityNetwork Parity.
With the Terminal type set to ASYN+X28, the parity
can be forced onto the network side by selecting the
approriate value.ro Enumeration .1.3.6.1.4.1.397.4.2.1.74 |
chanStatEscapeDelayEscape Delay.
Specifies the time in tenths of a second, that after
receiving an ESC character, all characters are
buffered before being forwarded. During this time the
ECHO facility is turned off, and is only restored
when the delay timer has expired.ro INTEGER .1.3.6.1.4.1.397.4.2.1.75 |
chanStatDestTsapDestination TSAP
The destination Transport Service Access Point.ro DisplayString .1.3.6.1.4.1.397.4.2.1.76 |
chanStatTransportLevelStateTransport Level State.
Transport Class 4 session statisticsro Enumeration .1.3.6.1.4.1.397.4.2.1.77 |
chanStatLinkStateLink State.
The current state of the Link Control Protocolro Enumeration .1.3.6.1.4.1.397.4.2.1.78 |
chanStatProtocolStateProtocol State.
The current state of the Protocol Control Protocolro Enumeration .1.3.6.1.4.1.397.4.2.1.79 |
chanStatProtocolProtocol
Displays the protocol configured for the channelro Enumeration .1.3.6.1.4.1.397.4.2.1.80 |
chanStatIdentityIdentity.
The current value of the IDENTITY field being put
into the Link Control Protocol or Protocol Control
Protocol commands.ro INTEGER .1.3.6.1.4.1.397.4.2.1.81 |
chanStatDlciRxDeDLCI RX Count.
The total number of Frames with the DE bit set received on this channel since it entered Data State.ro Counter .1.3.6.1.4.1.397.4.2.1.82 |
chanStatDlciTxDeDLCI TX Count.
The total number of Frames with the DE bit set transmitted on this channel since it entered Data State.ro Counter .1.3.6.1.4.1.397.4.2.1.83 |
chanStatDlciRxFecnDLCI RX Fecn Count.
The total number of Fecns (Forward Explicit Congestion Notification)
received on this channel since active.ro Counter .1.3.6.1.4.1.397.4.2.1.84 |
chanStatDlciTxFecnDLCI TX Fecn Count.
The total number of Fecns (Forward Explicit Congestion Notification)
transmitted on this channel since active.ro Counter .1.3.6.1.4.1.397.4.2.1.85 |
chanStatDlciRxBecnDLCI RX Becn Count.
The total number of Becns (Backwards Explicit Congestion Notification)
received on this channel since active.ro Counter .1.3.6.1.4.1.397.4.2.1.86 |
chanStatDlciTxBecnDLCI TX Becn Count.
The total number of Becns (Backwards Explicit Congestion Notification)
transmitted on this channel since active.ro Counter .1.3.6.1.4.1.397.4.2.1.87 |
chanStatConnectedToControllerIndexConnected to Index.
The INDEX of the CONTROLLER that this channel is
connected to.ro INTEGER .1.3.6.1.4.1.397.4.2.1.88 |
chanParamTableA table of channels associated with this Level 2
controller. SEQUENCE OF ChanParamEntry .1.3.6.1.4.1.397.4.3 |
chanParamEntryAn individual Channel. ChanParamEntry .1.3.6.1.4.1.397.4.3.1 |
chanParamIndexIndex.
The position of this channel in the controller channel
Table.ro INTEGER .1.3.6.1.4.1.397.4.3.1.1 |
chanParamNameName.
A user defined name for routing calls to this channel.rw DisplayString .1.3.6.1.4.1.397.4.3.1.2 |
chanParamDRCMaskDRC Mask.
A four character string used to force expicit routing
to the named resource.rw DisplayString .1.3.6.1.4.1.397.4.3.1.3 |
chanParamTerminalTypeTerminal Type.
If the channel is to perform terminal emulation, then the
setting defined will be specific to the users terminal envoking
emulation.rw Enumeration .1.3.6.1.4.1.397.4.3.1.4 |
chanParamCircuitTypeCircuit Type.
The type of circuit used on this channelrw Enumeration .1.3.6.1.4.1.397.4.3.1.5 |
chanParamOptionsOptions.
A range of channel options, these options may be
specified individually or added together.rw Enumeration .1.3.6.1.4.1.397.4.3.1.6 |
chanParamBuffersBuffers.
The number of system buffers allocated to this channel
for incoming calls.rw INTEGER .1.3.6.1.4.1.397.4.3.1.7 |
chanParamDiscModeDISC Mode.
The number of the character in decimal which forces
disconnection of the call.rw INTEGER .1.3.6.1.4.1.397.4.3.1.8 |
chanParamMenuNumberMenu Number.
Specifies which menu will be displayed to the user by the
presentation servicerw INTEGER .1.3.6.1.4.1.397.4.3.1.9 |
chanParamHelpNumberHelp Number.
Specifies which help screen will be displayed to the user by
the presentation service.rw INTEGER .1.3.6.1.4.1.397.4.3.1.10 |
chanParamNewsNumberNews Number.
The number of the menu which will be displayed if an
outgoing channel is unavailable.rw INTEGER .1.3.6.1.4.1.397.4.3.1.11 |
chanParamCallPriorityCall Priority.
Call and Resource priorities are used primarily for
providing alternate routing. For a call to succeed the
Call Priority on the incoming channel must be greater than
or equal to the Resource Priority on the outgoing channel.rw INTEGER .1.3.6.1.4.1.397.4.3.1.12 |
chanParamResourcePriorityResource Priority.
Call and Resource priorities are used primarily for
providing alternate routing. For a call to succeed the
Call Priority on the incoming channel must be greater than
or equal to the Resource Priority on the outgoing channel.rw INTEGER .1.3.6.1.4.1.397.4.3.1.13 |
chanParamPadEnablePad Enable.
The effect of the PAD Enable parameters are as follows:
enable PAD services enabled. The logical
channel will respond to X.29 packets.
enable-rev REVerse PAD enabled. When a call is
established to this channel, the
MegaPAC will generate an X.29
qualified data packet back to the
caller, containing the X.3 operating
values specified in the channel's
configuration.
enable-prof The X.3 profile settings for the channel
will be derived by referencing the
logical channel's NAME/ parameter to
the NAME/ field in the PROF file. The
X.3 settings as contained in the PROF
file record are then loaded onto the
channel.rw Enumeration .1.3.6.1.4.1.397.4.3.1.14 |
chanParamPadRecallPad Recall (1).
This parameter allows the user to escape from the data
transfer state to the PAD command state. The permitted
values are:
0 No PAD recall
1 Escape character is ^P
2 - 126 The decimal value specified is the escape characterrw INTEGER .1.3.6.1.4.1.397.4.3.1.15 |
chanParamEchoEcho.
Determines whether 'echo' is enabled or disabled. If
set to controlled, the echo facility is controlled by the
operator.rw Enumeration .1.3.6.1.4.1.397.4.3.1.16 |
chanParamDataForwardingData Forwarding.
This parameter controls which character or characters
cause the accumulated data to be forwarded. The possible
values may be added together to forward on one of a number
of conditions. The allowable values are:
0 Forward only on buffer full.
128 Forward on graphics characters.
64 Forward on all characters in columns 0 and 1 of the
International Alphabet No. 5.
1 Forward on A-Z, a-z and 0-9.
2 Forward on Carriage Return.
4 Forward on ESC, BEL, ENQ, ACK.
8 Forward on DEL, CAN, DC2.
16 Forward on EXT, EOT.
32 Forward on HT, LF, VT, FF.rw INTEGER .1.3.6.1.4.1.397.4.3.1.17 |
chanParamDelayDelay.
Specifies the idle time in tenths of a second, allowable
between successive characters before the accumulated data
is forwarded. A value of 0 disables the timeout facility.rw INTEGER .1.3.6.1.4.1.397.4.3.1.18 |
chanParamDRIDRI.
Flow control of terminal by the MegaPAC. Valid settings are:
enabled MegaPAC flow controls terminal using XON/XOFF.
cts MegaPAC flow controls terminal using CTS.
init+enable MegaPAC sends XON automatically on initialisation.
disable No flow control.rw Enumeration .1.3.6.1.4.1.397.4.3.1.19 |
chanParamPadSignalsPad Signals.
Enable X.28 prompts and/or messages to be displayed on
the users terminal.rw Enumeration .1.3.6.1.4.1.397.4.3.1.20 |
chanParamBreakBreak.
The Action the MegaPAC will take on receipt of a Break Signal.
The valid values are:
0 When the MegaPAC receives a Break Signal from the
terminal no action is taken.
1 When the MegaPAC receives a Break Signal from the
terminal it will transmit an INTERRUPT packet.
2 When the MegaPAC receives a Break Signal from the
terminal it will transmit an RESET packet.
5 When the MegaPAC receives a Break Signal from the
terminal it will transmit an INTERRUPT packet and an
indication of Break PAD message.
8 When the MegaPAC receives a Break Signal from the
terminal it will escape from data transfer state.
21 When the MegaPAC receives a Break Signal from the
terminal it will transmit an INTERRUPT packet and an
indication of Break PAD message, while setting (X3)
parameter (8) to the value 1 (discard any data
received from the network).rw INTEGER .1.3.6.1.4.1.397.4.3.1.21 |
chanParamPaddingPadding.
The number of NULL characters inserted after a carriage
return.rw INTEGER .1.3.6.1.4.1.397.4.3.1.22 |
chanParamFoldFold.
The number of characters output before line folding
occurs. Setting to 0 disables line folding.rw INTEGER .1.3.6.1.4.1.397.4.3.1.23 |
chanParamDROData Restraint Out.rw Enumeration .1.3.6.1.4.1.397.4.3.1.24 |
chanParamLFILFI.
This parameter controls linefeed insertion after a
carriage return. The valid settings are:
0 Line feed insertion disabled.
1 A linefeed is inserted after a carriage return,
in the data forwarded to the terminal.
4 A linefeed is sent to the terminal after echo of a
carriage return to the terminal.
5 As defined by values 1 + 4.
6 Linefeed inserted after carriage return from terminal
and each carriage return echoed to the terminal.
7 As defined by values 1 + 6.rw INTEGER .1.3.6.1.4.1.397.4.3.1.25 |
chanParamLFPadLFPad.
The number of NULL padding characters sent to a device
following a linefeed character.rw INTEGER .1.3.6.1.4.1.397.4.3.1.26 |
chanParamEditEdit.
Controls editing of text in data transfer state.rw Enumeration .1.3.6.1.4.1.397.4.3.1.27 |
chanParamCharDelChar Delete.
The keystroke used for deleting a character.rw INTEGER .1.3.6.1.4.1.397.4.3.1.28 |
chanParamBufferDelBuffer Delete.
The keystroke used for deleting the buffer.rw INTEGER .1.3.6.1.4.1.397.4.3.1.29 |
chanParamDispDisp.
The keystroke used to redisplay the data in the buffer.rw INTEGER .1.3.6.1.4.1.397.4.3.1.30 |
chanParamEditServiceSignalsEdit Service Signals.
This parameter enables the user to edit the PAD service
signals (echoing). The valid settings are:
0 No editing PAD service signals are echoed.
1 A '\' will be echoed for each character deleted.
2 A 'BS' character will be echoed for each character
deleted.
8 and 32-126 Specifies the decimal value of the ASCII
character to be echoed for each character deleted.rw INTEGER .1.3.6.1.4.1.397.4.3.1.31 |
chanParamEchoMaskEcho Mask.
This parameter controls the characters which should not
be echoed. The valid settings are:
0 All characters should be echoed to the terminal.
1 do not echo carriage return.
2 do not echo linefeed.
4 do not echo VT, HT and FF characters.
8 do not echo BEL and BS character.
16 do not echo ESC and ENQ.
32 do not echo ACK, NAK, STX, SOH, EOT, ETB or ETX.
64 do not echo editing characters as defined by
parameters 16, 17 and 18.
128 do not echo other control characters and DEL.rw INTEGER .1.3.6.1.4.1.397.4.3.1.32 |
chanParamParityTreatmentParity Treatment.
Determines the parity generation and checking performed
valid settings are:
0 No parity generation or checking.
1 Check parity.
2 Generate parity.
3 Check and generate parity.rw INTEGER .1.3.6.1.4.1.397.4.3.1.33 |
chanParamPageWaitPage Wait.
Specifies the number of lines to be transmitted, after
which the MegaPAC will wait until instructed by the user to
continue sending data (by entering <CTRL >Q). A value of
0 disables the page wait facility.rw INTEGER .1.3.6.1.4.1.397.4.3.1.34 |
chanParamForceForce.
The ASCII character which will force data forwarding,
0 disables forced data forwarding.rw INTEGER .1.3.6.1.4.1.397.4.3.1.35 |
chanParamBreakCharBreak Character.
The ASCII character in decimal which is used to
simulate a BREAK signal.rw INTEGER .1.3.6.1.4.1.397.4.3.1.36 |
chanParamNetworkParityNetwork Parity.
With the Terminal type set to ASYN+X28, the parity can
be forced onto the network side by selecting the approriate
value.rw Enumeration .1.3.6.1.4.1.397.4.3.1.37 |
chanParamEscapeDelayEscape Delay.
Specifies the time in tenths of a second, that after
receiving an ESC character, all characters are buffered
before being forwarded. During this time the ECHO facility
is turned off, and is only restored when the delay timer has
expired.rw INTEGER .1.3.6.1.4.1.397.4.3.1.38 |
chanParamStationAddressStation Address.
Physical Unit Address of the Cluster Controller.rw INTEGER .1.3.6.1.4.1.397.4.3.1.39 |
chanParamProvideXIDProvide XID.rw Enumeration .1.3.6.1.4.1.397.4.3.1.40 |
chanParamModeMode.
This parameter provides a number of additional connection
facilities for channels on virtual controllers.rw Enumeration .1.3.6.1.4.1.397.4.3.1.41 |
chanParamPortMatchPort Match.
This parameter optionally allows the Source
and Destination ports to be used in conjunction
with the IP address for routing.rw Enumeration .1.3.6.1.4.1.397.4.3.1.42 |
chanParamReverseTelnetPortReverse Telnet Port.
The port number which will respond to TELNET
open requests. The default value for TELNET
ports is '23'.rw INTEGER .1.3.6.1.4.1.397.4.3.1.43 |
chanParamBroadcastFilterTimerBroadcast Filter Timer.rw INTEGER .1.3.6.1.4.1.397.4.3.1.44 |
chanParamInhibitLearningInhibit Learning.
This parameter determines whether the 'bridge'
will work in Directed or Learning mode. If
InhibitLearning is set to 'Yes' then the bridge
will only forward frames whose addresses are fixed in
the forwarding table.rw Enumeration .1.3.6.1.4.1.397.4.3.1.45 |
chanParamRetainSessionRetain Session.
This parameter determines if and how a session will be
cleared down when the call is cleared. The parameter is
only applicable to channels (2) to (n). If set to NOTIFY
or NO the session will be cleared when the call disconnects
, NOTIFY will cause a NOTIFY RU to be sent indicating the
disconnection. If this parameter is set to YES then the
session will be retained on channel disconnection, this
is used to provide a hot key switching facility.rw Enumeration .1.3.6.1.4.1.397.4.3.1.46 |
chanParamPrinterTypePrinter Type.
If set to IBM the logical channel will act as an
appication system printer, otherwise it operates in
screen emulation mode. Only applicable to channels (2)
to (n).rw Enumeration .1.3.6.1.4.1.397.4.3.1.47 |
chanParamScreenPrinterScreen Printer.
If set to YES, screen printer requests are to be processed
and sent to this LU address (in this mode, the terminal
attaching to this channel MUST have a printer attached). If
set to NO, screen printing is supported via the LOCAL PRINTER
or the DEFAULT LOCAL PRINTER parameters.rw Enumeration .1.3.6.1.4.1.397.4.3.1.48 |
chanParamLocalPrinterLocal Printer.
This parameter specifies the channel to which screen printing
should be directed. It takes precedence over the value defined
by the DEFAULT LOCAL PRINTER at controller level. This parameter
may only be applied to channels (2) to (n).rw INTEGER .1.3.6.1.4.1.397.4.3.1.49 |
chanParamInterlockBindInterlock Bind.
This parameter is only applicable to channels (2) to (n).
When set to YES, an UNBIND request will be sent to the host
upon disconnecting. Note: when used in cojunction with a
4 character DRC mask, this setting will invoke a call set-up
when a BIND is received. This setting is often used when
sending a file transfer accross a Public Network.rw Enumeration .1.3.6.1.4.1.397.4.3.1.50 |
chanParamRedirectPrintToRedirect Printer To.
This parameter is only applicable to channels (2) to (n).
If set to (0), then no redirection takes place. Otherwise,
LU type 1 session data is output to the nominated logical
channel, each block being preceeded by the escape sequence
to switch to the auxiliary port, and followed by the
sequence to switch it back to the screen again. This is useful
in several environments, Foe example, using two LU channels it
enables a terminal user to interact with the Host, and receive
Host system prints at the same terminal (supporting a printer).rw INTEGER .1.3.6.1.4.1.397.4.3.1.51 |
chanParamLUBaseFirst LU defined by up-stream host.rw INTEGER .1.3.6.1.4.1.397.4.3.1.52 |
chanParamLUOffsetLU Offset.rw INTEGER .1.3.6.1.4.1.397.4.3.1.53 |
chanParamLUTotalTotal number of LUs to be allocated to down-
stream PU's.rw INTEGER .1.3.6.1.4.1.397.4.3.1.54 |
chanParamDlciBaseThe channel DLCI address.rw INTEGER .1.3.6.1.4.1.397.4.3.1.55 |
chanParamDlciAdjacentBaseThe DLCI number on the cross connected port in the
MegaPAC used when groups of channels are being switched
across the MegaPAC. Used in conjunction with the DRC mask.rw INTEGER .1.3.6.1.4.1.397.4.3.1.56 |
chanParamDlciPriorityA value from 0 to 32 indicating the relative priority of this
DLCI to the other data streams on this trunk, i.e. other DLCIs.
The higher the value the higher the priority.rw INTEGER .1.3.6.1.4.1.397.4.3.1.57 |
chanParamDlciATMDetermines whether fragmentation should be implemented on
frames on this link.rw Enumeration .1.3.6.1.4.1.397.4.3.1.58 |
chanParamDlciCirThe committed information rate for this DLCI - the units are in 80bits/secrw INTEGER .1.3.6.1.4.1.397.4.3.1.59 |
chanParamDlciBcBc(Burst Commit) - the committed burst that the MegaPAC
will allow to be transmitted on this DLCI; the units are 80bits.rw INTEGER .1.3.6.1.4.1.397.4.3.1.60 |
chanParamDlciBeBe(Burst Excess) is the excess above the Bc that will be
transmitted to the line by the MegaPAC in any given Tc.
The units are 80bits.rw INTEGER .1.3.6.1.4.1.397.4.3.1.61 |
chanParamDlciDeDE(Discard Eligibility) when set will indicate that in
a congested situation this frame should be discarded first.rw Enumeration .1.3.6.1.4.1.397.4.3.1.62 |
chanParamDlciProtocolSpecifies header in RFC 1480/1490 connectionsrw Enumeration .1.3.6.1.4.1.397.4.3.1.63 |
chanParamDlciDsapUsed in RFC 1490 SNA connections - each SAP identifies a specific
PU, hence by using different SAPs, multiple PUs can be multiplexed on the same
Frame Relay PVCrw INTEGER .1.3.6.1.4.1.397.4.3.1.64 |
chanParamDlciSsapUsed in RFC 1490 SNA connections - each SAP identifies a specific
PU, hence by using different SAPs, multiple PUs can be multiplexed on the same
Frame Relay PVCrw INTEGER .1.3.6.1.4.1.397.4.3.1.65 |
chanParamDlciPutypeUsed in RFC 1490 SNA connections - specifies type 2.0 or 2.1rw INTEGER .1.3.6.1.4.1.397.4.3.1.66 |
x25File OBJECT IDENTIFIER .1.3.6.1.4.1.397.5 |
x25FileSizeX25 file size.
The number of entries configured into the X25 file.rw INTEGER .1.3.6.1.4.1.397.5.1 |
x25TableA table of X.25 routing entries SEQUENCE OF X25Entry .1.3.6.1.4.1.397.5.2 |
x25Entry X25Entry .1.3.6.1.4.1.397.5.2.1 |
x25IndexIndex.
The index to an individual X.25 entryro INTEGER .1.3.6.1.4.1.397.5.2.1.1 |
x25NameName.
A 4 character name which is used to match on the 'NAME'
parameter of the channel on which a call will be routed
over the X.25 network.rw DisplayString .1.3.6.1.4.1.397.5.2.1.2 |
x25AddressGroupAddress Group.
An integer used to partition the X.25 routing tables.
Any match on a channel name will only take effect if
the channel 'AddressGroup' parameter is set to the same
value.rw INTEGER .1.3.6.1.4.1.397.5.2.1.3 |
x25AddressAddress.
The numeric address which is used to match on the
incoming X.25 address in a call request packet.rw DisplayString .1.3.6.1.4.1.397.5.2.1.4 |
x25UserDataUser Data
A text field in which Call User Data or Facilities may
be placed. The user data will be inserted into call
request packets generated by the MegaPAC.rw DisplayString .1.3.6.1.4.1.397.5.2.1.5 |
nameFile OBJECT IDENTIFIER .1.3.6.1.4.1.397.6 |
nameFileSizeName File Size.
The number of entries configured into the NAME file.rw INTEGER .1.3.6.1.4.1.397.6.1 |
nameTableA table of 'Name' entries. SEQUENCE OF NameEntry .1.3.6.1.4.1.397.6.2 |
nameEntry NameEntry .1.3.6.1.4.1.397.6.2.1 |
nameIndexIndex.
The index into the name table.ro INTEGER .1.3.6.1.4.1.397.6.2.1.1 |
nameNameName.
A string of up to 8 characters in length which is
typed in by the network user in order to establish
a connection to a specific resource.rw DisplayString .1.3.6.1.4.1.397.6.2.1.2 |
nameDRCMaskDRC Mask.
The four character resource (channel) name to which
the call will be directed.rw DisplayString .1.3.6.1.4.1.397.6.2.1.3 |
nameCallPriorityCall Priority.
The internal call priority which will be assigned to
the call.rw INTEGER .1.3.6.1.4.1.397.6.2.1.4 |
nameBillingBilling
If enabled, statistics relating to the call will be
sent to the billing file.rw Enumeration .1.3.6.1.4.1.397.6.2.1.5 |
nameOptionsOptions
Enables the appropriate terminal emulation options.rw Enumeration .1.3.6.1.4.1.397.6.2.1.6 |
passFile OBJECT IDENTIFIER .1.3.6.1.4.1.397.7 |
passFileSizePass File Size.
The number of entries configured into the PASSWORD
file.ro INTEGER .1.3.6.1.4.1.397.7.1 |
macFile OBJECT IDENTIFIER .1.3.6.1.4.1.397.8 |
macFileSizeMac File Size.
The number of entries configured into the MAC file.rw INTEGER .1.3.6.1.4.1.397.8.1 |
macTableA table of MAC entries SEQUENCE OF MacEntry .1.3.6.1.4.1.397.8.2 |
macEntry MacEntry .1.3.6.1.4.1.397.8.2.1 |
macIndexIndex.
An index to an individual entry in the MAC table.ro INTEGER .1.3.6.1.4.1.397.8.2.1.1 |
macNameName.
The level 2 controller name to which this entry
applies.rw DisplayString .1.3.6.1.4.1.397.8.2.1.2 |
macFunctionFunction.
The function field determines what action should be
taken if their is a match on this entry.rw Enumeration .1.3.6.1.4.1.397.8.2.1.3 |
macOptionsOptions.
Specific actions that may be envoked in conjunction
with the function field.rw Enumeration .1.3.6.1.4.1.397.8.2.1.4 |
macSelectorSelector.
This field can contain a string of between 0 and 32
Hexadecimal characters, that must be matched by the
Function DAD, CAD, CUD or FAC.rw DisplayString .1.3.6.1.4.1.397.8.2.1.5 |
macGeneratorGenerator.
This field can contain a string of between 0 and 32
Hexadecimal characters, and can have different purposes
depending on the Function or Options fields.rw DisplayString .1.3.6.1.4.1.397.8.2.1.6 |
ilanFile OBJECT IDENTIFIER .1.3.6.1.4.1.397.9 |
ilanFileSizeIlan File Size.
The number of entries configured into the ILAN file.rw INTEGER .1.3.6.1.4.1.397.9.1 |
ilanTableA table of ILAN entries SEQUENCE OF IlanEntry .1.3.6.1.4.1.397.9.2 |
ilanEntry IlanEntry .1.3.6.1.4.1.397.9.2.1 |
ilanIndexIndex.
An index to an individual entry in the ILAN table.ro INTEGER .1.3.6.1.4.1.397.9.2.1.1 |
ilanNameName.
The Resource which this entry applies to.rw DisplayString .1.3.6.1.4.1.397.9.2.1.2 |
ilanOptionsOptions
ISO Allows transport calls to be set up on the outgoing
channel.
EXPE Allows expedited data to be sent.rw Enumeration .1.3.6.1.4.1.397.9.2.1.3 |
ilanEthernetAddressEthernet Address.
The destination MAC address of the named host.rw DisplayString .1.3.6.1.4.1.397.9.2.1.4 |
ilanTSAPTSAP.
The Transport Service Access Point required on the
destination Host.rw DisplayString .1.3.6.1.4.1.397.9.2.1.5 |
elogFile OBJECT IDENTIFIER .1.3.6.1.4.1.397.10 |
elogFileSizeElog File Size.
The size of the error log file.rw INTEGER .1.3.6.1.4.1.397.10.1 |
elogTableA table of Error Log entries. SEQUENCE OF ElogEntry .1.3.6.1.4.1.397.10.2 |
elogEntry ElogEntry .1.3.6.1.4.1.397.10.2.1 |
elogIndexIndex.
The index to an Error Log entry.ro INTEGER .1.3.6.1.4.1.397.10.2.1.1 |
elogRecordRecord.
The Error Log entry in ascii format.ro DisplayString .1.3.6.1.4.1.397.10.2.1.2 |