Home/Catalog/RUIJIE-FIBER-MIB

RUIJIE-FIBER-MIB

AI MIB Summary

The RUIJIE-FIBER-MIB enables monitoring of optical transceiver parameters, including optical power levels, temperature, bias current, and voltage, on Ruijie network devices equipped with SFP or SFP+ fiber modules. It facilitates the retrieval of real-time diagnostic data and alarm status for installed fiber optic modules to support link integrity verification and hardware troubleshooting.

This module defines ruijie fiber module information mibs.
Main OID:
ruijieFiberMIB.1.3.6.1.4.1.4881.1.1.10.2.105
218
Objects
Active
Status
6
Dependencies

Imported Objects

SNMPv2-SMI
SNMPv2-TC
SNMPv2-CONF
RUIJIE-TC
RUIJIE-SMI
IF-MIB

Objects

218 total
Object Name
ruijieFiberMIBThis module defines ruijie fiber module information mibs.
MODULE-IDENTITY
.1.3.6.1.4.1.4881.1.1.10.2.105
ruijieFiberMIBObjects
OBJECT IDENTIFIER
.1.3.6.1.4.1.4881.1.1.10.2.105.1
ruijieFiberTableA table for getting Fiber Module information
SEQUENCE OF RuijieFiberEntry
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1
ruijieFiberEntryEntry of a Fiber Module information.
RuijieFiberEntry
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1
ruijieFiberPortIndexPort index of the port.ro
IfIndex (RUIJIE-TC)
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.1
ruijieFiberPortDescrDiscription of the port.ro
DisplayString
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.2
ruijieFiberTransceiverTypeTransceiver type of the Fiber module insered into the port.ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.3
ruijieFiberConnectorTypeConnector type of the Fiber module insered into the port. If the transceiver type of Fiber module is unknown(1), then this object contains a zero value.ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.4
ruijieFiberWavelengthThe value of wavelength of the Fiber module insered into the port. If the transceiver type of Fiber module is either fiber100CopperSFP(7) or fiber1000CopperSFP(13) (or fiber10GCopperSFPPlus(14), or fiber10GCopperXFP(19), or fiber40GCopperQSFPPlus(26), or fiber2500CopperSFP(28), or unknown(1)), then this object contains a zero value.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.5
ruijieFiberTransferDistanceSMFThe value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using single mode fiber for. The value is in units of kilometers. A value of zero means that the transceiver does not support single mode fiber.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.6
ruijieFiberTransferDistance62point5umOM1The value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 62.5 micron multimode (200 MHz*Km at 850 nm, 500 MHz*Km at 1310 nm) fiber. The value is in units of meters. A value of zero means that the transceiver does not support 62.5 micron multimode fiber or the Fiber module type is neither SFP/SFP+ nor QSFP+.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.7
ruijieFiberTransferDistance62point5umThe value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 62.5 micron core multimode (200 MHz*Km at 850 nm, 500 MHz*Km at 1310 nm) fiber. The value is in units of meters. A value of zero means that the transceiver does not support 62.5 micron multimode fiber or the Fiber module type is not XFP.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.8
ruijieFiberTransferDistance50umOM2The value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 50 micron multimode (500 MHz*Km at 850 nm for SFP module or at 850 nm and 1310 nm for QSFP+ module) fiber. The value is in units of meters. A value of zero means that the transceiver does not support 50 micron multimode fiber or the Fiber module type is neither SFP/SFP+ nor QSFP+.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.9
ruijieFiberTransferDistance50umThe value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 50 micron core multimode (500 MHz*Km at 850 nm and 1310 nm) fiber. The value is in units of meters. A value of zero means that the transceiver does not support 50 micron core multimode fiber or the Fiber module type is not XFP.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.10
ruijieFiberTransferDistance50umOM3The value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 50 micron multimode OM3(2000 MHz*Km) fiber. The value is in units of meters. A value of zero means that the transceiver does not support 50 micron multimode fiber or the Fiber module type is neither SFP/SFP+ nor QSFP+.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.11
ruijieFiberTransferDistanceEBW50umThe value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 2000 MHz*Km (850nm) extended bandwidth 50 micron core multimode fiber. The value is in units of meters. A value of zero means that the transceiver does not support extended bandwidth 50 micron multimode fiber or the Fiber module type is not XFP.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.12
ruijieFiberTransferDistanceCopperThe value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using copper cables. The value is in units of meters. A value of zero means that the transceiver does not support copper cables or the Fiber module type is neither SFP/SFP+ nor XFP.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.13
ruijieFiberTransferDistanceCableAssemblyThe value of transfer distance of the Fiber module insered into the port. This value specifies the link length of the Cable assembly passive. The value is in units of meters. A value of zero means that the transceiver is not a cable assemblyor or the Fiber module type is not QSFP+.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.14
ruijieFiberDDMSupportStatusThis object indicates that whether the Digital Diagnostic Monitors is implemeted.ro
TruthValue (SNMPv2-TC)
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.15
ruijieFiberSerialNumberThe serial number of the Fiber module insered into the port.ro
DisplayString
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.16
ruijieFiberTempThe temperature of the Fiber module insered into the port. The value is in units of degrees Celsius. If the ruijieFiberDDMSupportStatus is false, the temperature value is 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.17
ruijieFiberTempStatusThe status ok(2) indicates that the temperature of the Fiber module is in the normal level. The status warning(3) indicates that the temperature of the Fiber module exceeds high warning level or is below low warning level. The status alarm(4) indicates that the temperature of the Fiber module exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP(or not QSFP+), the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.18
ruijieFiberVoltageThe voltage of the Fiber module insered into the port. The value is in units of mVolts. If the ruijieFiberDDMSupportStatus is false, the voltage value is 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.19
ruijieFiberVoltageStatusThe status ok(2) indicates that the voltage of the Fiber module is in the normal level. The status warning(3) indicates that the voltage of the Fiber module exceeds high warning level or is below low warning level. The status alarm(4) indicates that the voltage of the Fiber module exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP(or not QSFP+), the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.20
ruijieFiberBiasThe bias of the Fiber module insered into the port. The value is in units of uA. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the bias value is 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.21
ruijieFiberBiasStatusThe status ok(2) indicates that the bias of the Fiber module is in the normal level. The status warning(3) indicates that the bias of the Fiber module exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias of the Fiber module exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.22
ruijieFiberChannel1BiasThe bias in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of uA. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the bias value in Channel 1 is 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.23
ruijieFiberChannel1BiasStatusThe status ok(2) indicates that the bias in the Channel 1 of QSFP+ is in the normal level. The status warning(3) indicates that the bias in the Channel 1 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias in the Channel 1 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.24
ruijieFiberChannel2BiasThe bias in Channel 2 of the QSFP+ Fiber module insered into the port. The value is in units of uA. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the bias value in Channel 2 is 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.25
ruijieFiberChannel2BiasStatusThe status ok(2) indicates that the bias in the Channel 2 of QSFP+ is in the normal level. The status warning(3) indicates that the bias in the Channel 2 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias in the Channel 2 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.26
ruijieFiberChannel3BiasThe bias in Channel 3 of the QSFP+ Fiber module insered into the port. The value is in units of uA. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the bias value in Channel 3 is 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.27
ruijieFiberChannel3BiasStatusThe status ok(2) indicates that the bias in the Channel 3 of QSFP+ is in the normal level. The status warning(3) indicates that the bias in the Channel 3 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias in the Channel 3 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.28
ruijieFiberChannel4BiasThe bias in Channel 4 of the QSFP+ Fiber module insered into the port. The value is in units of uA. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the bias value in Channel 4 is 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.29
ruijieFiberChannel4BiasStatusThe status ok(2) indicates that the bias in the Channel 4 of QSFP+ is in the normal level. The status warning(3) indicates that the bias in the Channel 4 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias in the Channel 4 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.30
ruijieFiberRXpowerIntegerpartThe integer part of Rx power of the Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the integer part of Rx power value is -100(means that the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.31
ruijieFiberRXpowerDecimalpartThe decimal part of Rx power of the Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the decimal part of Rx power value is -100(means that the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.32
ruijieFiberRXpowertypeThe value indicates whether the received power measurement represents average input optical power(2) or oma(3). If the ruijieFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP (or not QSFP+), the value is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.33
ruijieFiberRXpowerStatusThe status ok(2) indicates that the Rx power of the Fiber module is in the normal level. The status warning(3) indicates that the Rx power of the Fiber module exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power of the Fiber module exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.34
ruijieFiberChannel1RXpowerIntegerpartThe integer part of Rx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Rx power value in Channel 1 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.35
ruijieFiberChannel1RXpowerDecimalpartThe decimal part of Rx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Rx power value in Channel 1 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.36
ruijieFiberChannel1RXpowertypeThe value indicates whether the received power measurement represents average input optical power(2) or oma(3) in Channel 1 of QSFP+. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the value is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.37
ruijieFiberChannel1RXpowerStatusThe status ok(2) indicates that the Rx power in the Channel 1 of QSFP+ is in the normal level. The status warning(3) indicates that the Rx power in the Channel 1 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power in the Channel 1 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.38
ruijieFiberChannel2RXpowerIntegerpartThe integer part of Rx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Rx power value in Channel 1 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.39
ruijieFiberChannel2RXpowerDecimalpartThe decimal part of Rx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Rx power value in Channel 2 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.40
ruijieFiberChannel2RXpowertypeThe value indicates whether the received power measurement represents average input optical power(2) or oma(3) in Channel 2 of QSFP+. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the value is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.41
ruijieFiberChannel2RXpowerStatusThe status ok(2) indicates that the Rx power in the Channel 2 of QSFP+ is in the normal level. The status warning(3) indicates that the Rx power in the Channel 2 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power in the Channel 2 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.42
ruijieFiberChannel3RXpowerIntegerpartThe integer part of Rx power in Channel 3 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Rx power value in Channel 3 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.43
ruijieFiberChannel3RXpowerDecimalpartThe decimal part of Rx power in Channel 3 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Rx power value in Channel 3 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.44
ruijieFiberChannel3RXpowertypeThe value indicates whether the received power measurement represents average input optical power(2) or oma(3) in Channel 3 of QSFP+. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the value is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.45
ruijieFiberChannel3RXpowerStatusThe status ok(2) indicates that the Rx power in the Channel 3 of QSFP+ is in the normal level. The status warning(3) indicates that the Rx power in the Channel 3 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power in the Channel 3 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.46
ruijieFiberChannel4RXpowerIntegerpartThe integer part of Rx power in Channel 4 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Rx power value in Channel 4 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.47
ruijieFiberChannel4RXpowerDecimalpartThe decimal part of Rx power in Channel 4 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Rx power value in Channel 4 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.48
ruijieFiberChannel4RXpowertypeThe value indicates whether the received power measurement represents average input optical power(2) or oma(3) in Channel 4 of QSFP+. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the value is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.49
ruijieFiberChannel4RXpowerStatusThe status ok(2) indicates that the Rx power in the Channel 4 of QSFP+ is in the normal level. The status warning(3) indicates that the Rx power in the Channel 4 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power in the Channel 4 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.50
ruijieFiberTXpowerIntegerpartThe integer part of Tx power of the Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the integer part of Tx power value is -100(means that the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.51
ruijieFiberTXpowerDecimalpartThe decimal part of Tx power of the Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the decimal part of Tx power value is -100(means that the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.52
ruijieFiberTXpowerStatusThe status ok(2) indicates that the Tx power of the Fiber module is in the normal level. The status warning(3) indicates that the Tx power of the Fiber module exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power of the Fiber module exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.53
ruijieFiberChannel1TXpowerIntegerpartThe integer part of Tx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Tx power value in Channel 1 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.54
ruijieFiberChannel1TXpowerDecimalpartThe decimal part of Tx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Tx power value in Channel 1 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.55
ruijieFiberChannel1TXpowerStatusThe status ok(2) indicates that the Tx power in the Channel 1 of QSFP+ is in the normal level. The status warning(3) indicates that the Tx power in the Channel 1 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power in the Channel 1 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.56
ruijieFiberChannel2TXpowerIntegerpartThe integer part of Tx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Tx power value in Channel 1 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.57
ruijieFiberChannel2TXpowerDecimalpartThe decimal part of Tx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Tx power value in Channel 2 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.58
ruijieFiberChannel2TXpowerStatusThe status ok(2) indicates that the Tx power in the Channel 2 of QSFP+ is in the normal level. The status warning(3) indicates that the Tx power in the Channel 2 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power in the Channel 2 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.59
ruijieFiberChannel3TXpowerIntegerpartThe integer part of Tx power in Channel 3 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Tx power value in Channel 3 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.60
ruijieFiberChannel3TXpowerDecimalpartThe decimal part of Tx power in Channel 3 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Tx power value in Channel 3 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.61
ruijieFiberChannel3TXpowerStatusThe status ok(2) indicates that the Tx power in the Channel 3 of QSFP+ is in the normal level. The status warning(3) indicates that the Tx power in the Channel 3 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power in the Channel 3 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.62
ruijieFiberChannel4TXpowerIntegerpartThe integer part of Tx power in Channel 4 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the integer part of Tx power value in Channel 4 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.63
ruijieFiberChannel4TXpowerDecimalpartThe decimal part of Tx power in Channel 4 of the QSFP+ Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the decimal part of Tx power value in Channel 4 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.64
ruijieFiberChannel4TXpowerStatusThe status ok(2) indicates that the Tx power in the Channel 4 of QSFP+ is in the normal level. The status warning(3) indicates that the Tx power in the Channel 4 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power in the Channel 4 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP+, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.65
ruijieFiberRXpowerSignThe sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.66
ruijieFiberChannel1RXpowerSignThe sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.67
ruijieFiberChannel2RXpowerSignThe sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.68
ruijieFiberChannel3RXpowerSignThe sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.69
ruijieFiberChannel4RXpowerSignThe sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.70
ruijieFiberTXpowerSignThe sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.71
ruijieFiberChannel1TXpowerSignThe sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.72
ruijieFiberChannel2TXpowerSignThe sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.73
ruijieFiberChannel3TXpowerSignThe sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.74
ruijieFiberChannel4TXpowerSignThe sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.75
ruijieFiberRXpowerThe Rx power of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.76
ruijieFiberChannel1RXpowerThe Rx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.77
ruijieFiberChannel2RXpowerThe Rx power in Channel 2 of the QSFP+ Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.78
ruijieFiberChannel3RXpowerThe Rx power in Channel 3 of the QSFP+ Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.79
ruijieFiberChannel4RXpowerThe Rx power in Channel 4 of the QSFP+ Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.80
ruijieFiberTXpowerThe Tx power of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.81
ruijieFiberChannel1TXpowerThe Tx power in Channel 1 of the QSFP+ Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.82
ruijieFiberChannel2TXpowerThe Tx power in Channel 2 of the QSFP+ Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.83
ruijieFiberChannel3TXpowerThe Tx power in Channel 3 of the QSFP+ Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.84
ruijieFiberChannel4TXpowerThe Tx power in Channel 4 of the QSFP+ Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.85
ruijieFiberWavelengthExactThe value of wavelength of the Fiber module insered into the port. If the transceiver type of Fiber module is either fiber100CopperSFP(7) or fiber1000CopperSFP(13) (or fiber10GCopperSFPPlus(14), or fiber10GCopperXFP(19), or fiber40GCopperQSFPPlus(26), or fiber2500CopperSFP(28), or unknown(1)), then this object contains a NA value.ro
DisplayString
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.86
ruijieFiberTransferDistance50umOM4The value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 50 micron multimode OM4(4700 MHz*Km) fiber. The value is in units of meters. A value of zero means that the transceiver does not support 50 micron multimode fiber or the Fiber module type is neither SFP/SFP+ nor QSFP+.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.87
ruijieFiberTransferDistanceSMFExtThe value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using single mode fiber for. The value is in units of meters. A value of zero means that the transceiver does not support single mode fiber.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.88
ruijieFiberBandWidthThe value of transfer maximum available bandwidth of the Fiber module insered into the port. The value is in units of Mbit/s. A value of zero means that the transceiver does not insert or unknown type.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.89
ruijieFiberFormFactorIndicates the form factor of the Fiber module insered into the port.ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.90
ruijieFiberRXpowerLowWarnThresholdThe Rx power low warning threshold of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.91
ruijieFiberRXpowerHighWarnThresholdThe Rx power high warning threshold of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.92
ruijieFiberRXpowerLowAlarmThresholdThe Rx power low alarm threshold of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.93
ruijieFiberRXpowerHighAlarmThresholdThe Rx power high alarm threshold of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.94
ruijieFiberTXpowerLowWarnThresholdThe Tx power low warning threshold of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.95
ruijieFiberTXpowerHighWarnThresholdThe Tx power high warning threshold of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.96
ruijieFiberTXpowerLowAlarmThresholdThe Tx power low alarm threshold of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.97
ruijieFiberTXpowerHighAlarmThresholdThe Tx power high alarm threshold of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.98
ruijieFiberChannel5BiasThe bias in Channel 5 of the QSFP CMIS Fiber module insered into the port. The value is in units of uA. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the bias value in Channel 5 is 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.99
ruijieFiberChannel5BiasStatusThe status ok(2) indicates that the bias in the Channel 5 of QSFP CMIS is in the normal level. The status warning(3) indicates that the bias in the Channel 5 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias in the Channel 5 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.100
ruijieFiberChannel6BiasThe bias in Channel 6 of the QSFP CMIS Fiber module insered into the port. The value is in units of uA. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the bias value in Channel 6 is 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.101
ruijieFiberChannel6BiasStatusThe status ok(2) indicates that the bias in the Channel 6 of QSFP CMIS is in the normal level. The status warning(3) indicates that the bias in the Channel 6 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias in the Channel 6 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.102
ruijieFiberChannel7BiasThe bias in Channel 7 of the QSFP CMIS Fiber module insered into the port. The value is in units of uA. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the bias value in Channel 7 is 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.103
ruijieFiberChannel7BiasStatusThe status ok(2) indicates that the bias in the Channel 7 of QSFP CMIS is in the normal level. The status warning(3) indicates that the bias in the Channel 7 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias in the Channel 7 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.104
ruijieFiberChannel8BiasThe bias in Channel 8 of the QSFP CMIS Fiber module insered into the port. The value is in units of uA. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the bias value in Channel 8 is 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.105
ruijieFiberChannel8BiasStatusThe status ok(2) indicates that the bias in the Channel 8 of QSFP CMIS is in the normal level. The status warning(3) indicates that the bias in the Channel 8 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias in the Channel 8 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.106
ruijieFiberChannel5RXpowerIntegerpartThe integer part of Rx power in Channel 5 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the integer part of Rx power value in Channel 5 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.107
ruijieFiberChannel5RXpowerDecimalpartThe decimal part of Rx power in Channel 5 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the decimal part of Rx power value in Channel 5 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.108
ruijieFiberChannel5RXpowertypeThe value indicates whether the received power measurement represents average input optical power(2) or oma(3) in Channel 5 of QSFP CMIS. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the value is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.109
ruijieFiberChannel5RXpowerStatusThe status ok(2) indicates that the Rx power in the Channel 5 of QSFP CMIS is in the normal level. The status warning(3) indicates that the Rx power in the Channel 5 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power in the Channel 5 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.110
ruijieFiberChannel6RXpowerIntegerpartThe integer part of Rx power in Channel 6 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the integer part of Rx power value in Channel 6 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.111
ruijieFiberChannel6RXpowerDecimalpartThe decimal part of Rx power in Channel 6 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the decimal part of Rx power value in Channel 6 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.112
ruijieFiberChannel6RXpowertypeThe value indicates whether the received power measurement represents average input optical power(2) or oma(3) in Channel 6 of QSFP CMIS. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the value is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.113
ruijieFiberChannel6RXpowerStatusThe status ok(2) indicates that the Rx power in the Channel 6 of QSFP CMIS is in the normal level. The status warning(3) indicates that the Rx power in the Channel 6 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power in the Channel 6 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.114
ruijieFiberChannel7RXpowerIntegerpartThe integer part of Rx power in Channel 7 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the integer part of Rx power value in Channel 7 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.115
ruijieFiberChannel7RXpowerDecimalpartThe decimal part of Rx power in Channel 7 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the decimal part of Rx power value in Channel 7 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.116
ruijieFiberChannel7RXpowertypeThe value indicates whether the received power measurement represents average input optical power(2) or oma(3) in Channel 7 of QSFP CMIS. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the value is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.117
ruijieFiberChannel7RXpowerStatusThe status ok(2) indicates that the Rx power in the Channel 7 of QSFP CMIS is in the normal level. The status warning(3) indicates that the Rx power in the Channel 7 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power in the Channel 7 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.118
ruijieFiberChannel8RXpowerIntegerpartThe integer part of Rx power in Channel 8 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the integer part of Rx power value in Channel 8 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.119
ruijieFiberChannel8RXpowerDecimalpartThe decimal part of Rx power in Channel 8 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the decimal part of Rx power value in Channel 8 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.120
ruijieFiberChannel8RXpowertypeThe value indicates whether the received power measurement represents average input optical power(2) or oma(3) in Channel 8 of QSFP CMIS. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the value is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.121
ruijieFiberChannel8RXpowerStatusThe status ok(2) indicates that the Rx power in the Channel 8 of QSFP CMIS is in the normal level. The status warning(3) indicates that the Rx power in the Channel 8 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power in the Channel 8 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.122
ruijieFiberChannel5TXpowerIntegerpartThe integer part of Tx power in Channel 5 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the integer part of Tx power value in Channel 5 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.123
ruijieFiberChannel5TXpowerDecimalpartThe decimal part of Tx power in Channel 5 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the decimal part of Tx power value in Channel 5 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.124
ruijieFiberChannel5TXpowerStatusThe status ok(2) indicates that the Tx power in the Channel 5 of QSFP CMIS is in the normal level. The status warning(3) indicates that the Tx power in the Channel 5 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power in the Channel 5 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.125
ruijieFiberChannel6TXpowerIntegerpartThe integer part of Tx power in Channel 6 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the integer part of Tx power value in Channel 6 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.126
ruijieFiberChannel6TXpowerDecimalpartThe decimal part of Tx power in Channel 6 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the decimal part of Tx power value in Channel 6 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.127
ruijieFiberChannel6TXpowerStatusThe status ok(2) indicates that the Tx power in the Channel 6 of QSFP CMIS is in the normal level. The status warning(3) indicates that the Tx power in the Channel 6 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power in the Channel 6 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.128
ruijieFiberChannel7TXpowerIntegerpartThe integer part of Tx power in Channel 7 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the integer part of Tx power value in Channel 7 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.129
ruijieFiberChannel7TXpowerDecimalpartThe decimal part of Tx power in Channel 7 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the decimal part of Tx power value in Channel 7 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.130
ruijieFiberChannel7TXpowerStatusThe status ok(2) indicates that the Tx power in the Channel 7 of QSFP CMIS is in the normal level. The status warning(3) indicates that the Tx power in the Channel 7 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power in the Channel 7 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.131
ruijieFiberChannel8TXpowerIntegerpartThe integer part of Tx power in Channel 8 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the integer part of Tx power value in Channel 8 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.132
ruijieFiberChannel8TXpowerDecimalpartThe decimal part of Tx power in Channel 8 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the decimal part of Tx power value in Channel 8 is -100(means the value is invalid).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.133
ruijieFiberChannel8TXpowerStatusThe status ok(2) indicates that the Tx power in the Channel 8 of QSFP CMIS is in the normal level. The status warning(3) indicates that the Tx power in the Channel 8 exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power in the Channel 8 exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is not QSFP CMIS, the status is unknown(1).ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.134
ruijieFiberChannel5RXpowerSignThe sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.135
ruijieFiberChannel6RXpowerSignThe sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.136
ruijieFiberChannel7RXpowerSignThe sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.137
ruijieFiberChannel8RXpowerSignThe sign (-1) indicates that the Rx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.138
ruijieFiberChannel5TXpowerSignThe sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.139
ruijieFiberChannel6TXpowerSignThe sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.140
ruijieFiberChannel7TXpowerSignThe sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.141
ruijieFiberChannel8TXpowerSignThe sign (-1) indicates that the Tx power value is lower than 0, while sign (1) is higher than 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.142
ruijieFiberChannel5RXpowerThe Rx power in Channel 5 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.143
ruijieFiberChannel6RXpowerThe Rx power in Channel 6 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.144
ruijieFiberChannel7RXpowerThe Rx power in Channel 7 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.145
ruijieFiberChannel8RXpowerThe Rx power in Channel 8 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.146
ruijieFiberChannel5TXpowerThe Tx power in Channel 5 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.147
ruijieFiberChannel6TXpowerThe Tx power in Channel 6 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.148
ruijieFiberChannel7TXpowerThe Tx power in Channel 7 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.149
ruijieFiberChannel8TXpowerThe Tx power in Channel 8 of the QSFP CMIS Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.150
ruijieFiberTransferDistance50umOM5The value of transfer distance of the Fiber module insered into the port. This value specifies the link length that is supported by the transceiver while operating in compliance with the applicable standards using 50 micron multimode OM5(4700 MHz*Km at 850nm, 2470 MHz*km at 953nm) fiber. The value is in units of meters. A value of zero means that the transceiver does not support 50 micron multimode fiber or the Fiber module type is neither SFP/SFP+ nor QSFP+.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.151
ruijieFiberModeThis object indicates the fiber type.ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.152
ruijieFiberTempLowWarnThresholdThe temperature low warning threshold of the Fiber module insered into the port. The value is in units of degrees Celsius. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.153
ruijieFiberTempHighWarnThresholdThe temperature high warning threshold of the Fiber module insered into the port. The value is in units of degrees Celsius. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.154
ruijieFiberTempLowAlarmThresholdThe temperature low alarm threshold of the Fiber module insered into the port. The value is in units of degrees Celsius. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.155
ruijieFiberTempHighAlarmThresholdThe temperature high alarm threshold of the Fiber module insered into the port. The value is in units of degrees Celsius. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.156
ruijieFiberVoltageLowWarnThresholdThe voltage low warning threshold of the Fiber module insered into the port. The value is in units of mVolts. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.157
ruijieFiberVoltageHighWarnThresholdThe voltage high warning threshold of the Fiber module insered into the port. The value is in units of mVolts. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.158
ruijieFiberVoltageLowAlarmThresholdThe voltage low alarm threshold of the Fiber module insered into the port. The value is in units of mVolts. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.159
ruijieFiberVoltageHighAlarmThresholdThe voltage high alarm threshold of the Fiber module insered into the port. The value is in units of mVolts. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.160
ruijieFiberBiasLowWarnThresholdThe bias low warning threshold of the Fiber module insered into the port. The value is in units of uA. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.161
ruijieFiberBiasHighWarnThresholdThe bias high warning threshold of the Fiber module insered into the port. The value is in units of uA. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.162
ruijieFiberBiasLowAlarmThresholdThe bias low alarm threshold of the Fiber module insered into the port. The value is in units of uA. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.163
ruijieFiberBiasHighAlarmThresholdThe bias high alarm threshold of the Fiber module insered into the port. The value is in units of uA. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.164
ruijieFiberTransceiverTypeStrTransceiver type of the Fiber module inserted into the port.ro
DisplayString
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.165
ruijieFiberConnectorTypeStrConnector type of the Fiber module inserted into the port.ro
DisplayString
.1.3.6.1.4.1.4881.1.1.10.2.105.1.1.1.166
ruijieFiberVendorTableA table of Vendor info entries.
SEQUENCE OF RuijieFiberVendorEntry
.1.3.6.1.4.1.4881.1.1.10.2.105.1.2
ruijieFiberVendorEntryEntry contains Vendor info.
RuijieFiberVendorEntry
.1.3.6.1.4.1.4881.1.1.10.2.105.1.2.1
ruijieFiberVendorPortIndexThe port index of Vendor info .ro
IfIndex (RUIJIE-TC)
.1.3.6.1.4.1.4881.1.1.10.2.105.1.2.1.1
ruijieFiberVendorNameThe description of vendor name.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4881.1.1.10.2.105.1.2.1.2
ruijieFiberVendorOUIThe description of vendor oui.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4881.1.1.10.2.105.1.2.1.3
ruijieFiberVendorPartNumberThe description of vendor part number.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4881.1.1.10.2.105.1.2.1.4
ruijieFiberVendorRevThe description of vendor revision.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4881.1.1.10.2.105.1.2.1.5
ruijieFiberManufacturingDateThe description of vendor's manufacturing date.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4881.1.1.10.2.105.1.2.1.6
ruijieFiberEncodingThe description of vendor's encoding type.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4881.1.1.10.2.105.1.2.1.7
ruijieFiberOMCTableA table of OMC fiber info entries.
SEQUENCE OF RuijieFiberOMCEntry
.1.3.6.1.4.1.4881.1.1.10.2.105.1.3
ruijieFiberOMCEntryEntry contains OMC fiber info.
RuijieFiberOMCEntry
.1.3.6.1.4.1.4881.1.1.10.2.105.1.3.1
ruijieFiberOMCPortIndexPort index of the port.ro
IfIndex (RUIJIE-TC)
.1.3.6.1.4.1.4881.1.1.10.2.105.1.3.1.1
ruijieFiberOMCRxpowerThe Rx power of the Fiber module insered into the port. Use a comma to separate multiple optical power values for multiple channels, fill in key-value pairs, connect the key and value with an equal sign, the key is the channel name, and the value is the optical power. The unit of the optical power value is dbw.ro
DisplayString
.1.3.6.1.4.1.4881.1.1.10.2.105.1.3.1.2
ruijieFiberOMCTxpowerThe Tx power of the Fiber module insered into the port. Use a comma to separate multiple optical power values for multiple channels, fill in key-value pairs, connect the key and value with an equal sign, the key is the channel name, and the value is the optical power. The unit of the optical power value is dbw.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4881.1.1.10.2.105.1.3.1.3
ruijieFiberOMCWavelengthThe value of wavelength of the Fiber module insered into the port. The unit is nm. If it is a single wavelength, report a single value, for example: 1310. If it is a wavelength range, report the wavelength range, for example: 1310-1312. The reported string does not include the unit.ro
DisplayString
.1.3.6.1.4.1.4881.1.1.10.2.105.1.3.1.4
ruijieFiberOMCTranslengthThe value of transfer distance of the Fiber module insered into the port. The unit is km. If it is a single distance, report a single value, for example: 20 If there are multiple distances in fiber mode, report multiple sets of data separated by commas. The format of each group of data is a key-value pair, the key and value are connected with =, the key is the fiber grade, and the value is the corresponding distance, such as 'OM1=20, OM2=30'ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.4881.1.1.10.2.105.1.3.1.5
ruijieFiberOMCPortTypePort type of the Fiber module insered into the port.ro
DisplayString
.1.3.6.1.4.1.4881.1.1.10.2.105.1.3.1.6
ruijieFiberChannelTableA table of fiber channel information entries.
SEQUENCE OF RuijieFiberChannelEntry
.1.3.6.1.4.1.4881.1.1.10.2.105.1.4
ruijieFiberChannelEntryEntry contains fiber channel information.
RuijieFiberChannelEntry
.1.3.6.1.4.1.4881.1.1.10.2.105.1.4.1
ruijieFiberChannelPortIndexThe port index of fiber channel information.ro
IfIndex (RUIJIE-TC)
.1.3.6.1.4.1.4881.1.1.10.2.105.1.4.1.1
ruijieFiberChannelIndexThe channel index of fiber channel.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.4.1.2
ruijieFiberChannelBiasThe bias of the Fiber module insered into the port. The value is in units of uA. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the bias value is 0.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.4.1.3
ruijieFiberChannelBiasStatusThe status ok(2) indicates that the bias of the Fiber module is in the normal level. The status warning(3) indicates that the bias of the Fiber module exceeds high warning level or is below low warning level. The status alarm(4) indicates that the bias of the Fiber module exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the status is unknown(1).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.4.1.4
ruijieFiberChannelRXpowerThe Rx power of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.4.1.5
ruijieFiberChannelRXpowertypeThe value indicates whether the received power measurement represents average input optical power(2) or oma(3). If the ruijieFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP (or not QSFP+), the value is unknown(1).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.4.1.6
ruijieFiberChannelRXpowerStatusThe status ok(2) indicates that the Rx power of the Fiber module is in the normal level. The status warning(3) indicates that the Rx power of the Fiber module exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Rx power of the Fiber module exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the status is unknown(1).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.4.1.7
ruijieFiberChannelTXpowerThe Tx power of the Fiber module insered into the port. The value is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.4.1.8
ruijieFiberChannelTXpowerStatusThe status ok(2) indicates that the Tx power of the Fiber module is in the normal level. The status warning(3) indicates that the Tx power of the Fiber module exceeds high warning level or is below low warning level. The status alarm(4) indicates that the Tx power of the Fiber module exceeds high alarm level or is below low alarm level. If the ruijieFiberDDMSupportStatus is false or the Fiber module type is neither SFP/SFP+ nor XFP, the status is unknown(1).ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.1.4.1.9
ruijieFiberChannelAPRThe transceiver automatic power reduction state. The status on(2) indicates that the transceiver is in automatic power reduction state. The status off(1) indicates that the transceiver is not in automatic power reduction state.ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.1.4.1.10
ruijieFiberAntifakeMIBTraps
OBJECT IDENTIFIER
.1.3.6.1.4.1.4881.1.1.10.2.105.2
ruijieFiberAntifakeIntfNameDescThe description of the interface.ro
DisplayString
.1.3.6.1.4.1.4881.1.1.10.2.105.2.1
ruijieFiberAntifakeSerialNumberDescThe description of the serial number of the fiber module.ro
DisplayString
.1.3.6.1.4.1.4881.1.1.10.2.105.2.2
ruijieFiberAntifakeTrapWhen detect the fiber module is not original ruijie fiber module, then this trap will be sent.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4881.1.1.10.2.105.2.3
ruijieFiberMIBConformance
OBJECT IDENTIFIER
.1.3.6.1.4.1.4881.1.1.10.2.105.3
ruijieFiberMIBCompliances
OBJECT IDENTIFIER
.1.3.6.1.4.1.4881.1.1.10.2.105.3.1
ruijieFiberMIBGroups
OBJECT IDENTIFIER
.1.3.6.1.4.1.4881.1.1.10.2.105.3.2
ruijieFiberEventMIBTraps
OBJECT IDENTIFIER
.1.3.6.1.4.1.4881.1.1.10.2.105.4
ruijieFiberEventReasonThe reason of the fiber invalid event.ro
Enumeration
.1.3.6.1.4.1.4881.1.1.10.2.105.4.1
ruijieFiberEventDescThe description of the fiber invalid event.ro
DisplayString
.1.3.6.1.4.1.4881.1.1.10.2.105.4.2
ruijieFiberRemoveEventTrapWhen detect the fiber has been removed, then this trap will be sent.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4881.1.1.10.2.105.4.3
ruijieFiberInsertEventTrapWhen detect the fiber has been inserted, then this trap will be sent.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4881.1.1.10.2.105.4.4
ruijieFiberInvalidTrapDetect the fiber invalid event.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4881.1.1.10.2.105.4.5
ruijieFiberInvalidResumeTrapThe fiber resume from invalid event.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4881.1.1.10.2.105.4.6
ruijieFiberAlarmValueThe realtime value of the fiber invalid event. The value of power is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.4.7
ruijieFiberAlarmThresholdValueThe threshold value of the fiber invalid event. The value of power is in units of dbm, which needs to be divided by 100. The value of -10000 means the value is invalid.ro
INTEGER
.1.3.6.1.4.1.4881.1.1.10.2.105.4.8
ruijieFiberSpeedMismatchWhen detect the fiber has been inserted and the speed of the optical module does not match the speed supported by the interface, then this trap will be sent.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4881.1.1.10.2.105.4.9
ruijieFiberUnCertifiedWhen detect the optical module on interface is not within the whitelist, then this trap will be sent.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4881.1.1.10.2.105.4.10
ruijieFiberUnCertifiedClearWhen detect the optical module which is not within the whitelist offline, then this trap will be sent.
NOTIFICATION-TYPE
.1.3.6.1.4.1.4881.1.1.10.2.105.4.11
RUIJIE-FIBER-MIB - SNMP MIB Reference | MIBs Explorer