RAID-Adapter-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for RAID-Adapter-MIB.
106
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
106 total| Object Name |
|---|
perc OBJECT IDENTIFIER .1.3.6.1.4.1.16 |
RFC1213-MIB Unknown .1.3.6.1.4.1.16 |
percRAID OBJECT IDENTIFIER .1.3.6.1.4.1.16.1 |
percRaidMib OBJECT IDENTIFIER .1.3.6.1.4.1.16.1.1 |
adapterTableA List of Adapter Entries containing Information/Properties
about the Adapters in the System. SEQUENCE OF AdapterEntry .1.3.6.1.4.1.16.1.1.1 |
adapterEntryAn entry in the Adapter Table. Each Entry corresponds
to one Adapter in the System. AdapterEntry .1.3.6.1.4.1.16.1.1.1.1 |
adpAdapterNumberThe Adapter Number for this Instance of Adapter Object. This
Entry in the Table, contains Information about the Adapter
Number specified by this variable.ro INTEGER .1.3.6.1.4.1.16.1.1.1.1.1 |
numLogicalDrivesNumber of Logical Drives Configured on this Adapter.ro INTEGER .1.3.6.1.4.1.16.1.1.1.1.2 |
firmwareVersionThe Firmware Version of the Firmware running on this Adapter.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.16.1.1.1.1.3 |
biosVersionThe Bios Version of the BIOS Present in the Flash ROM on
this Adapter.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.16.1.1.1.1.4 |
dramSizeInMBAmount of DRAM in Mega Bytes present on this Adapter.ro INTEGER .1.3.6.1.4.1.16.1.1.1.1.5 |
chipSetTypeMotherboard Chipset Type for which the Adapter ASIC is
Configured.ro Enumeration .1.3.6.1.4.1.16.1.1.1.1.6 |
rebuildRateInPercentRebuild Rate for this Adapter. This determines the Priority of
Rebuild/Check-Consistency/Reconstruct Operations versus the
Read-Write Operations.rw INTEGER .1.3.6.1.4.1.16.1.1.1.1.7 |
flushIntervalInternal Cache Flush Interval for Logical Drives in WriteBack
Mode.rw Enumeration .1.3.6.1.4.1.16.1.1.1.1.8 |
maxConcurrentCmdsMaximum Concurrent Commands Supported by the Adapter.ro INTEGER .1.3.6.1.4.1.16.1.1.1.1.9 |
spinupDelayThis is the Spinup Delay for Spinning Up Physical Drives
at Firmware Initialization Time. The Physical Drives are
divided into Groups, each containing the number of drives
indicated by the spinupCount variable. spinupDelay
variable is the amount of delay used before the drives in
the next group are issued a SPINUP Command.ro INTEGER .1.3.6.1.4.1.16.1.1.1.1.10 |
spinupCountThis is the Spinup Count for Spinning up Physical Drives at
Firmware Initialization Time. The Physical Drives are divided
into Groups, each containing the number of drives indicated
by this variable. All the drives in a group are issued SPINUP
Command without any delay. Next group is given SPINUP Commands
after a delay indicated by the spinupDelay variable.ro INTEGER .1.3.6.1.4.1.16.1.1.1.1.11 |
adpIOReadsPerSecNumber of IO Reads/sec statistics for this adapter.ro INTEGER .1.3.6.1.4.1.16.1.1.1.1.12 |
adpIOWritesPerSecNumber of IO Writes/sec statistics for this adapter.ro INTEGER .1.3.6.1.4.1.16.1.1.1.1.13 |
adpReadKBsPerSecAmount of Data Transferred in KBs/sec due to READ Transfers.ro INTEGER .1.3.6.1.4.1.16.1.1.1.1.14 |
adpWriteKBsPerSecAmount of Data Transferred in KBs/sec due to WRITE Transfers.ro INTEGER .1.3.6.1.4.1.16.1.1.1.1.15 |
adpReadFailuresPerSecNumber of Read-Failures/sec statistics for this adapter.ro INTEGER .1.3.6.1.4.1.16.1.1.1.1.16 |
adpWriteFailuresPerSecNumber of Write-Failures/sec statistics for this adapter.ro INTEGER .1.3.6.1.4.1.16.1.1.1.1.17 |
scanChannelsUse this Variable to Discover the Non-Disk Devices attached
to the Adapter. Set this Variable to startscan (an integer
value of 2) to start the Channel Scanning.rw Enumeration .1.3.6.1.4.1.16.1.1.1.1.18 |
logicaldriveTableA List of Logical Drive Entries containing Information/Properties
about the Logical Drives Configured in the System. SEQUENCE OF LogicaldriveEntry .1.3.6.1.4.1.16.1.1.2 |
logicaldriveEntryAn Entry in the Logical Drive Table. LogicaldriveEntry .1.3.6.1.4.1.16.1.1.2.1 |
ldAdapterNumberThe Adapter Number for this Instance of Adapter/LogicalDrive
object.ro INTEGER .1.3.6.1.4.1.16.1.1.2.1.1 |
logicalDriveNumberLogical Drive Number for this Logical Drive Entry.ro INTEGER .1.3.6.1.4.1.16.1.1.2.1.2 |
statusThe Status of this Logical Drive.rw Enumeration .1.3.6.1.4.1.16.1.1.2.1.3 |
sizeInMBThe Configured Size of this Logical Drive.ro INTEGER .1.3.6.1.4.1.16.1.1.2.1.4 |
raidLevelConfigured Raid Level for this Logical Drive.ro Enumeration .1.3.6.1.4.1.16.1.1.2.1.5 |
stripeSizeConfigured Stripe Size for this Logical Drive.ro Enumeration .1.3.6.1.4.1.16.1.1.2.1.6 |
readPolicyConfigured Read Policy for this Logical Drive.rw Enumeration .1.3.6.1.4.1.16.1.1.2.1.7 |
writePolicyConfigured Write Policy for this Logical Drive.rw Enumeration .1.3.6.1.4.1.16.1.1.2.1.8 |
cachePolicyConfigured Cache Policy for this Logical Drive.rw Enumeration .1.3.6.1.4.1.16.1.1.2.1.9 |
enquiryStringSCSI Inquiry String for this Logical Drive.ro DisplayString .1.3.6.1.4.1.16.1.1.2.1.10 |
numberOfSpansNumber of Arrays across which this Logical Drive is Spanning.ro INTEGER .1.3.6.1.4.1.16.1.1.2.1.11 |
numberOfStripesConfigured Number of Stripes for this Logical Drive.ro INTEGER .1.3.6.1.4.1.16.1.1.2.1.12 |
checkConsistencyOrInitializeProgressCheck Consistency or Initialize Progress for this Logical Drive
if the Logical Drive Status is checkconsistencyinprogress or
initializeinprogress.ro DisplayString .1.3.6.1.4.1.16.1.1.2.1.13 |
ldIOReadsPerSecNumber of IO Reads/sec Statistics for this Logical Drive.ro INTEGER .1.3.6.1.4.1.16.1.1.2.1.14 |
ldIOWritesPerSecNumber of IO Writes/sec Statistics for this Logical Drive.ro INTEGER .1.3.6.1.4.1.16.1.1.2.1.15 |
ldReadKBsPerSecAmount of Data Transferred in KBs/sec due to READ Transfers.ro INTEGER .1.3.6.1.4.1.16.1.1.2.1.16 |
ldWriteKBsPerSecAmount of Data Transferred in KBs/sec due to WRITE Transfers.ro INTEGER .1.3.6.1.4.1.16.1.1.2.1.17 |
ldReadFailuresPerSecNumber of Read-Failures/sec Statistics for this Logical Drive.ro INTEGER .1.3.6.1.4.1.16.1.1.2.1.18 |
ldWriteFailuresPerSecNumber of Write-Failures/sec Statistics for this Logical Drive.ro INTEGER .1.3.6.1.4.1.16.1.1.2.1.19 |
physicaldriveTableA List of Physical Device Entries containing Information
about the Physical Devices in the System. SEQUENCE OF PhysicaldriveEntry .1.3.6.1.4.1.16.1.1.3 |
physicaldriveEntryAn Entry in the Physical Drive Table. PhysicaldriveEntry .1.3.6.1.4.1.16.1.1.3.1 |
physAdapterNumberThe Adapter Number for this Instance of Adapter/Physical-Drive
Instance.ro INTEGER .1.3.6.1.4.1.16.1.1.3.1.1 |
physChannelChannel Number at Which this Physical Drive is Present.ro INTEGER .1.3.6.1.4.1.16.1.1.3.1.2 |
targetIDSCSI Target ID at Which This Physical Drive is Present.ro INTEGER .1.3.6.1.4.1.16.1.1.3.1.3 |
stateCurrent State of this Physical Drive.rw Enumeration .1.3.6.1.4.1.16.1.1.3.1.4 |
arrayPositionArray is a group of Physical Drives used to Configure Logical
Drives. This String Variable has values of the type Ai-j.
Example: A1-2 implies that this drive is 2nd member of Array-1.ro DisplayString .1.3.6.1.4.1.16.1.1.3.1.5 |
sizeMBActual Size of this Physical Drive.ro INTEGER .1.3.6.1.4.1.16.1.1.3.1.6 |
deviceTypeDevice Type of this Physical Drive.ro Enumeration .1.3.6.1.4.1.16.1.1.3.1.7 |
inquiryStringSCSI Inquiry String for this Device.ro DisplayString .1.3.6.1.4.1.16.1.1.3.1.8 |
scsiLevelANSI SCSI Level Conformance of this Device.ro Enumeration .1.3.6.1.4.1.16.1.1.3.1.9 |
syncNegotiationThis indicates whether Firmware is Enabled or Disabled to
perform the Synchronous Negotiation for this Device.ro Enumeration .1.3.6.1.4.1.16.1.1.3.1.10 |
qtagsThis indicates the Maximum Number of Concurrent Commands
Firmware Issues to this Drive.ro Enumeration .1.3.6.1.4.1.16.1.1.3.1.11 |
rebuildProgressRebuild Progress for this Physical Drive if the Physical
Drive State is Rebuild.ro DisplayString .1.3.6.1.4.1.16.1.1.3.1.12 |
mediumErrorsMedium Errors Occurred on this Drive Since it was Configured.ro INTEGER .1.3.6.1.4.1.16.1.1.3.1.13 |
otherErrorsOther Errors Occurred on this Drive Since it was Configured.ro INTEGER .1.3.6.1.4.1.16.1.1.3.1.14 |
channelTableA List of Channel Entries containing Information/Properties
about the Channels on the Adapter. SEQUENCE OF ChannelEntry .1.3.6.1.4.1.16.1.1.4 |
channelEntryAn Entry in the channel table. ChannelEntry .1.3.6.1.4.1.16.1.1.4.1 |
chanAdapterNumberThe Adapter Number for this Instance of Adapter/Channel Instance.ro INTEGER .1.3.6.1.4.1.16.1.1.4.1.1 |
channelChannel Number for this Channel.ro INTEGER .1.3.6.1.4.1.16.1.1.4.1.2 |
terminationsCurrent Terminations Effective on this Channelro Enumeration .1.3.6.1.4.1.16.1.1.4.1.3 |
channelStatusCurrent Activity Status (QUIET/ACTIVE) for this Channel.ro Enumeration .1.3.6.1.4.1.16.1.1.4.1.4 |
ioReadsPerSecThe Total IO-Reads/Sec Statistics on all Adapters.ro INTEGER .1.3.6.1.4.1.16.1.1.9 |
ioWritesPerSecThe Total IO-Writes/Sec Statistics on all Adapters.ro INTEGER .1.3.6.1.4.1.16.1.1.10 |
readKBsPerSecThe Total Read KBs Per Second Statistics on all Adapters.ro INTEGER .1.3.6.1.4.1.16.1.1.11 |
writeKBsPerSecThe Total Write KBs Per Second Statistics on all Adapters.ro INTEGER .1.3.6.1.4.1.16.1.1.12 |
readFailuresPerSecThe Total Read Failures Per Second Statistics on all Adapters.ro INTEGER .1.3.6.1.4.1.16.1.1.13 |
writeFailuresPerSecThe Total Write Failures Per Second Statistics on all Adapters.ro INTEGER .1.3.6.1.4.1.16.1.1.14 |
raidTraps OBJECT IDENTIFIER .1.3.6.1.4.1.16.1.1.200 |
rtConfigUpdatedAdapter-%d: A New Configuration has been written. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9001 |
rtPhysicalDriveStateChangeAdapter-%d, Channel-%d, Target-%d: Drive State Changed from %s to %s. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9002 |
rtLogicalDriveStateChangeAdapter-%d, Logical Drive-%d: State Changed from %s to %s. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9003 |
rtInitializeStartedAdapter-%d, Logical Drive-%d: Initialization Started. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9004 |
rtInitializeCompletedAdapter-%d, Logical Drive-%d: Initialization Completed Successfully. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9005 |
rtInitializeAbortedAdapter-%d, Logical Drive-%d: Initialization Aborted by User. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9006 |
rtInitializeFailedAdapter-%d, Logical Drive-%d: Initialization Failed. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9007 |
rtCheckConsistencyStartedAdapter-%d, Logical Drive-%d: Check Consistency Started. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9008 |
rtCheckConsistencyCompletedAdapter-%d, Logical Drive-%d: Check Consistency Completed. No
Inconsistencies Found. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9009 |
rtCheckConsistencyAbortedAdapter-%d, Logical Drive-%d: Check Consistency Aborted by User. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9010 |
rtConsistencyCorrectedAdapter-%d, Logical Drive-%d: Check Consistency Operation Completed.
Inconsistencies have been Cured. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9011 |
rtCheckConsistencyFailedAdapter-%d, Logical Drive-%d: Check Consistency Failed. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9012 |
rtReconstructionStartedAdapter-%d, Logical Drive-%d: Reconstruction Started. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9013 |
rtReconstructionCompletedAdapter-%d, Logical Drive-%d: Reconstruction Completed Successfully. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9014 |
rtReconstructionFailedAdapter-%d, Logical Drive-%d: Reconstruction Failed. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9015 |
rtPredictiveFailuresExceededAdapter-%d, Channel-%d, Target-%d: Reported Predictive Failure.
Drive Identification String = %s
Sense Key = 0x%x, ASC = 0x%x, ASCQ = 0x%x. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9016 |
rtPredictiveFailuresFalseAdapter-%d, Channel-%d, Target-%d: Reported Failure Prediction
Threshold Exceeded [FALSE].
Drive Identification String = %s
Sense Key = 0x%x, ASC = 0x%x, ASCQ = 0x%x. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9017 |
rtCheckConditionStatusAdapter-%d, Channel-%d, Target-%d: Command Completed with
Sense_Key-0x%x ASC-0x%x ASCQ-0x%x. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9018 |
rtNewDriveInsertedAdapter-%d, Channel-%d, Target-%d: New Device Inserted. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9019 |
rtBatteryMissingAdapter-%d: Battery Module is missing. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9020 |
rtBatteryVolatageLowAdapter-%d: Battery Module Voltage is Low. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9021 |
rtBatteryTemperatureHighAdapter-%d: Battery Module Temperature Exceeded Danger Threshold. TRAP-TYPE .1.3.6.1.4.1.16.1.1.200.0.9022 |
rtAdapterNumberAdapter Number for which Trap is generated.ro INTEGER .1.3.6.1.4.1.16.1.1.200.1001 |
rtLogicalDriveNumberLogical Drive Number for which Trap is generated.ro INTEGER .1.3.6.1.4.1.16.1.1.200.1002 |
rtChannelNumberChannel Number on the Adapter for which Trap is Generated.ro INTEGER .1.3.6.1.4.1.16.1.1.200.1003 |
rtTargetIDDevice ID of the Physical Drive for which Trap is Generated.ro INTEGER .1.3.6.1.4.1.16.1.1.200.1004 |
rtOldDriveStateOld State of Logical/Physical Drive, when a State Change Trap
is Generated.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.16.1.1.200.1005 |
rtNewDriveStateNew State of Logical/Physical Drive, when a State Change Trap
is Generated.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.16.1.1.200.1006 |
rtSenseKeyCheck Condition Sense-Key reported by Physical Drive for which
Trap is Generated.ro INTEGER .1.3.6.1.4.1.16.1.1.200.1007 |
rtASCCheck Condition Additional Sense Code (ASC) reported by Physical
Drive for which Trap is Generated.ro INTEGER .1.3.6.1.4.1.16.1.1.200.1008 |
rtASCQCheck Condition Additional Sense Code Qualifier (ASCQ) reported by
Physical Drive for which Trap is Generated.ro INTEGER .1.3.6.1.4.1.16.1.1.200.1009 |
rtDriveVendorVendor Identification String from the SCSI Inquiry Data for the
Drive.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.16.1.1.200.1010 |