QWESCOM-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
443
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
443 total| Object Name |
|---|
qwescom OBJECT IDENTIFIER .1.3.6.1.4.1.3662 |
RFC1155-SMI Unknown .1.3.6.1.4.1.3662 |
oemTree OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662 |
oem OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662 |
qproprietaryMib2 OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.1 |
qsnmp OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.1.11 |
qsnmpCommunityTableA list of SNMP Community entries. The
maximum number of SNMP Communities are
five. SEQUENCE OF QsnmpCommunityEntry .1.3.6.1.4.1.3662.3662.3662.1.11.1 |
qsnmpCommunityEntryOne entry in the table. QsnmpCommunityEntry .1.3.6.1.4.1.3662.3662.3662.1.11.1.1 |
qsnmpCommunityIndexA unique value which identifies each
SNMP Community.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.1.11.1.1.1 |
qsnmpCommunityRightsThe first and third
qsnmpCommunityIndex have read-write
permission while the others have
read-only privilege. Values 0 =
ReadOnly, and 1 = ReadWritero Enumeration .1.3.6.1.4.1.3662.3662.3662.1.11.1.1.2 |
qsnmpCommunityNameThe SNMP Community Name used to access
the unit with the associated permission
from the qsnmpCommunityRights.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.1.11.1.1.3 |
qsnmpNMSTableA list of SNMP Network Management
System (NMS) entries. SEQUENCE OF QsnmpNMSEntry .1.3.6.1.4.1.3662.3662.3662.1.11.2 |
qsnmpNMSEntryOne entry in the table. QsnmpNMSEntry .1.3.6.1.4.1.3662.3662.3662.1.11.2.1 |
qsnmpNMSIndexA unique value which identifies each
NMS.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.1.11.2.1.1 |
qsnmpNMSIpAddressThe IP Address of a Network Management
System, which is allowed to access MIB
variables.rw IpAddress .1.3.6.1.4.1.3662.3662.3662.1.11.2.1.2 |
qsnmpTrapTableA list of IP Address entries
associated with traps. SEQUENCE OF QsnmpTrapEntry .1.3.6.1.4.1.3662.3662.3662.1.11.3 |
qsnmpTrapEntryOne entry in the table. QsnmpTrapEntry .1.3.6.1.4.1.3662.3662.3662.1.11.3.1 |
qsnmpTrapIndexA unique value which identifies each
IP Address.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.1.11.3.1.1 |
qsnmpTrapIpAddressThe IP Address of an IP entity, which
is allowed to receive SNMP Trap
events.rw IpAddress .1.3.6.1.4.1.3662.3662.3662.1.11.3.1.2 |
qsnmpForwardTrapThe flag which enables(1)/disables(2)
SNMP Trap events to be transmitted.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.1.11.4 |
qproducts OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.2 |
qslots OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.3 |
qFlowClass OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.4 |
qClassDefinitionMaxEntriesThe number of Class Definition
entries.ro Counter .1.3.6.1.4.1.3662.3662.3662.4.1 |
qClassDefinitionTableA list of Class Definition entries.
The number of entries is given by the
value of qClassDefinitionMaxEntries. SEQUENCE OF QClassDefinitionEntry .1.3.6.1.4.1.3662.3662.3662.4.2 |
qClassDefinitionEntryOne entry in the table. QClassDefinitionEntry .1.3.6.1.4.1.3662.3662.3662.4.2.1 |
qClassDefinitionIndexA unique value for each class
definition. Values 0 and 1 are reserved
for internal use.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.2.1.1 |
qClassDefinitionAliasA textual string containing user
defined information about the Class
Definition.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.4.2.1.2 |
qClassDefinitionParentClassIDThe qClassDefinitionIndex value of the
parent for this Class Definition.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.2.1.3 |
qClassDefinitionFlowTypeThe type of Class Definition being
created. INVALID causes the current
Class Definition Entry to be removed.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.4.2.1.4 |
qClassDefinitionSourceIPMaskThe IP address mask for the source.rw IpAddress .1.3.6.1.4.1.3662.3662.3662.4.2.1.5 |
qClassDefinitionSourceIPLowerBoundThe first source IP address which
matches the class (after masking).rw IpAddress .1.3.6.1.4.1.3662.3662.3662.4.2.1.6 |
qClassDefinitionSourceIPUpperBoundThe last source IP address which
matches the class (after masking).rw IpAddress .1.3.6.1.4.1.3662.3662.3662.4.2.1.7 |
qClassDefinitionDestIPMaskThe IP address mask for the
destination.rw IpAddress .1.3.6.1.4.1.3662.3662.3662.4.2.1.8 |
qClassDefinitionDestIPLowerBoundThe first destination IP address which
matches the class (after masking).rw IpAddress .1.3.6.1.4.1.3662.3662.3662.4.2.1.9 |
qClassDefinitionDestIPUpperBoundThe last destination IP address which
matches the class (after masking).rw IpAddress .1.3.6.1.4.1.3662.3662.3662.4.2.1.10 |
qClassDefinitionDSMaskThe DS/TOS byte mask value.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.2.1.11 |
qClassDefinitionDSLowerBoundThe first DS/TOS byte value which
matches the class (after masking).rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.2.1.12 |
qClassDefinitionDSUpperBoundThe last DS/TOS byte value which
matches the class (after masking).rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.2.1.13 |
qClassDefinitionWellKnownApplicationThe type of application to match.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.4.2.1.14 |
qClassDefinitionProtocolThe IP protocol which matches the
class.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.4.2.1.15 |
qClassDefinitionSourcePortLowerBoundThe first source UDP/TCP port which
matches the class. Only valid if
qClassDefinitionWellKnownApplication =
UNSPECIFIED, and
qClassDefinitionProtocol = (ALL,
UDPTCP, UDP, or TCP).rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.2.1.16 |
qClassDefinitionSourcePortUpperBoundThe last source UDP/TCP port which
matches the class. Only valid if
qClassDefinitionWellKnownApplication =
UNSPECIFIED, and
qClassDefinitionProtocol = (ALL,
UDPTCP, UDP, or TCP).rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.2.1.17 |
qClassDefinitionDestPortLowerBoundThe first dest UDP/TCP port which
matches the class. Only valid if
qClassDefinitionWellKnownApplication =
UNSPECIFIED, and
qClassDefinitionProtocol = (ALL,
UDPTCP, UDP, or TCP).rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.2.1.18 |
qClassDefinitionDestPortUpperBoundThe last dest UDP/TCP port which
matches the class. Only valid if
qClassDefinitionWellKnownApplication =
UNSPECIFIED, and
qClassDefinitionProtocol = (ALL,
UDPTCP, UDP, or TCP).rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.2.1.19 |
qClassDefinitionFlowAgingTimeThe number of seconds to use as the
aging time for LIF related flow
information.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.2.1.20 |
qPolicyDefinitionMaxEntriesThe number of Policy Definition
entries.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.3 |
qPolicyDefinitionTableA list of Policy Definition entries.
The number of entries is given by the
value of qPolicyDefinitionMaxEntries. SEQUENCE OF QPolicyDefinitionEntry .1.3.6.1.4.1.3662.3662.3662.4.4 |
qPolicyDefinitionEntry QPolicyDefinitionEntry .1.3.6.1.4.1.3662.3662.3662.4.4.1 |
qPolicyDefinitionIndexA unique value for each policy
definition. Values 0 and 1 are
reserved for internal use.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.4.1.1 |
qPolicyDefinitionAliasA textual string containing user
defined information about the Policy
Definition.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.4.4.1.2 |
qPolicyDefinitionTypeThe type of Policy Definition. DELETE
causes the current definition to be
removed.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.4.4.1.3 |
qPolicyDefinitionLPThe logical interface this policy
relates to.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.4.1.4 |
qPolicyDefinitionStartTimeThe time of day this policy takes
effect. NULL = always in effect.rw TimeDateString .1.3.6.1.4.1.3662.3662.3662.4.4.1.5 |
qPolicyDefinitionEndTimeThe time of day this policy stops
taking effect. NULL = always in
effect.rw TimeDateString .1.3.6.1.4.1.3662.3662.3662.4.4.1.6 |
qPolicyDefinitionDayofWeekBit flags which indicate the day of
week. Bit 0 = Monday, 1 = Tuesday,
2 = Weds, 4 = Thurs, 8 = Fri, 16 = Sat,
32 = Sun, 64 = Holidays.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.4.1.7 |
qPolicyDefinitionPipeIDThe pipe definition this policy
references.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.4.1.8 |
qPolicyDefinitionClassIDThe class definition this policy
references.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.4.1.9 |
qPolicyDefinitionChannelizedBit flags indicating which Classing range is used to create
unique channels. 0 = off, 1 = Source IP, 2 = Dest IP
4 = Source Port, 8 = Dest Port, 16 = Protocol, 32 = DS.
The maximum number of channels (1-255) is set into the upper
byte of this value. If a channel is selected, the default
maximum is 16.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.4.1.10 |
qPolicyDefinitionOutboundDSValueThe DS/TOS byte value to set in
outbound PDUs. A value of 256 indicates
no replacement.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.4.1.11 |
qPolicyDefinitionPriorityThe relative priority of this policy.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.4.1.12 |
qPolicyDefinitionEventThe type of event which causes this
policy to come into effect.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.4.4.1.13 |
qPipeDefinitionMaxEntriesThe number of Pipe Definition
entries.ro Counter .1.3.6.1.4.1.3662.3662.3662.4.5 |
qPipeDefinitionTableA list of Pipe Definition entries. The
number of entries is given by the value
of qPipeDefinitionMaxEntries. SEQUENCE OF QPipeDefinitionEntry .1.3.6.1.4.1.3662.3662.3662.4.6 |
qPipeDefinitionEntry QPipeDefinitionEntry .1.3.6.1.4.1.3662.3662.3662.4.6.1 |
qPipeDefinitionIndexA unique value for each pipe
definition. Values 0 and 1 are reserved
for internal use.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.6.1.1 |
qPipeDefinitionAliasA textual string containing user
defined information about the Pipe
Definition.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.4.6.1.2 |
qPipeDefinitionTypeThe type of Pipe Definition. DELETE
causes the current definition to be
removed.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.4.6.1.3 |
qPipeDefinitionCircuitIDThe WAN circuit this pipe relates to.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.6.1.4 |
qPipeDefinitionBandwidthThe sustained bandwidth (bits/sec) of
this pipe.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.6.1.5 |
qPipeDefinitionPeakPeak bandwidth of this pipe
(bits/sec). Write-acces not supported
in Release 1.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.4.6.1.6 |
qPipeDefinitionMBSThe maximum burst size (bytes).
Write-acces not supported in Release
1.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.4.6.1.7 |
qPipeDefinitionBufferAllocationThe maximum queuing delay for this
pipe.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.6.1.8 |
qPipeDefinitionDelayThe maximum queuing delay for this
pipe.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.4.6.1.9 |
qPipeDefinitionPhyIdxThe physical index for the port.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.4.6.1.10 |
qPipeDefinitionPhyTypeThe physical type for the port.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.4.6.1.11 |
qClassStatisticsTableA list of Class Statistics entries.
The number of entries is given by the
value of qClassDefinitionMaxEntries. SEQUENCE OF QClassStatisticsEntry .1.3.6.1.4.1.3662.3662.3662.4.7 |
qClassStatisticsEntry QClassStatisticsEntry .1.3.6.1.4.1.3662.3662.3662.4.7.1 |
qClassStatisticsIndexA unique value for each class stats
entry. These match their corresponding
Class Definition entry index.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.4.7.1.1 |
qClassStatisticsAliasA textual string containing user
defined information about the Class
Definition this stats entry relates
to.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3662.3662.3662.4.7.1.2 |
qClassStatisticsTransmittedCountThe number of bytes transmitted.ro Counter .1.3.6.1.4.1.3662.3662.3662.4.7.1.3 |
qClassStatisticsDiscardCountThe number of bytes discarded.ro Counter .1.3.6.1.4.1.3662.3662.3662.4.7.1.4 |
qClassStatisticsFallbackCountThe number of bytes transmitted on the
'all others' flow.ro Counter .1.3.6.1.4.1.3662.3662.3662.4.7.1.5 |
qatm OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.5 |
qatmCircuitTableA list of ATM circuit entries. SEQUENCE OF QatmCircuitEntry .1.3.6.1.4.1.3662.3662.3662.5.1 |
qatmCircuitEntryOne entry in the table. QatmCircuitEntry .1.3.6.1.4.1.3662.3662.3662.5.1.1 |
qatmCircuitIdA unique value for this circuit
definition.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.1.1.1 |
qatmCircuitAliasA unique alias for this circuit
definition.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.5.1.1.2 |
qatmCircuitUNIThe UNI interface number for this
circuit.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.1.1.3 |
qatmCircuitLogicalInterfaceThe LIF to assign this Circuit to. LIF
1 is reserved as an Ethernet
identifier.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.1.1.4 |
qatmCircuitVpiThe Virtual Path Identifier for this
circuit.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.1.1.5 |
qatmCircuitFirstVciThe Virtual Path Identifier for this
circuit.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.1.1.6 |
qatmCircuitModeDetermining the multiplexing mode for this connection.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.5.1.1.7 |
qatmCircuitStatusSetting a value of 1 adds/modifies an
entry. Setting a value of 2 deletes a
current entry.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.5.1.1.8 |
qatmUniTableThis table contains the QWES.com
proprietary configuration parameters
for an ATM local Interface (UNI). SEQUENCE OF QatmUniEntry .1.3.6.1.4.1.3662.3662.3662.5.2 |
qatmUniEntryThis list contains the QWES.com
proprietary configuration
parameters and state variables and is
indexed by ifIndex values ATM
interface. QatmUniEntry .1.3.6.1.4.1.3662.3662.3662.5.2.1 |
qatmSpanPortThe SPAN port associates with
this UNI.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.2.1.1 |
qatmUniNameUnique Name for this UNI.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.5.2.1.2 |
qatmUniAliasA textual string containing user
defined information about the UNI.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.5.2.1.3 |
qatmUniTrapStatusIndicates whether the Link Up/Link
Down traps should be generated for this
interface.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.5.2.1.4 |
qatmUniMaxQueueDelayxxxxrw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.2.1.5 |
qatmUniMinAllocBufferxxxxrw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.2.1.6 |
qatmUniSharedBufferxxxxrw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.2.1.7 |
qatmUniLinkBandwidthxxxxrw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.2.1.8 |
qatmUniLinkDelayxxxxrw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.2.1.9 |
qatmUniBandwidthGranularityxxxxrw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.2.1.10 |
qatmUniIlmiStatusEnable/Disable ILMI function for this UNI.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.5.2.1.11 |
qatmUniRowStatusThis object is used to create, delete
or modify a row in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.3662.3662.3662.5.2.1.12 |
qatmVplTableThe Virtual Path Link (VPL) table. SEQUENCE OF QatmVplEntry .1.3.6.1.4.1.3662.3662.3662.5.3 |
qatmVplEntryOne entry in the table. QatmVplEntry .1.3.6.1.4.1.3662.3662.3662.5.3.1 |
qatmVplMaxVccThe maximum number of VCCs initialized
and active for this VPC. If the value
is 0, then this VPC is only for
management purposes and is not assigned
to a scheduler.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.3.1.1 |
qatmVplLowestVciThe start of a contiguous and
increasing VCI range whose maximum is
given by the maximum VCCs allowed.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.3.1.2 |
qatmVplMaxQueueDelayThe maximum queueing delay in
milliseconds (msec). Combining this
value with the sustained rate will
determine the maximum buffering
allowed.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.3.1.3 |
qatmVplReservedBufferThe minimum amount of buffering that
this VCC will be allocated to use.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.3.1.4 |
qatmVplBwGranularityThe bandwidth granularity can be apply
to this VPC.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.3.1.5 |
qatmVplMtuThe MTU size can be apply to this
VPC.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.3.1.6 |
qatmVplSharedBufferThe amount of buffering to be assigned
to a VPC for sharing on a First In
First Out (FIFO) basis between flows on
this VPC.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.3.1.7 |
qatmVclTableThe Virtual Channel Link (VCL) table. SEQUENCE OF QatmVclEntry .1.3.6.1.4.1.3662.3662.3662.5.4 |
qatmVclEntryOne entry in the table. QatmVclEntry .1.3.6.1.4.1.3662.3662.3662.5.4.1 |
qatmVclBwGranularityThe bandwidth granularity can be apply
to this VCC.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.4.1.1 |
qatmVclMaxSubChannelsThe maximum number of sub-channels
supported on this Virtual Circuit.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.4.1.2 |
qatmVclMaxQueueDelayThe maximum queueing delay in
milliseconds (msec). Combining this
value with the sustained rate will
determine the maximum buffering
allowed.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.4.1.3 |
qatmVclReservedBufferThe minimum reserved buffer in bytes
that this VCC will be allocated to
use.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.4.1.4 |
qatmVclSharedBufferThe amount of buffering to be assigned
to a VCC for sharing on a First In
First Out (FIFO) basis between flows on
this VCC.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.4.1.5 |
qatmAal5TableThe ATM Adaptation Layer 5 (Aal5) table. SEQUENCE OF QatmAal5Entry .1.3.6.1.4.1.3662.3662.3662.5.5 |
qatmAal5EntryOne entry in the table. QatmAal5Entry .1.3.6.1.4.1.3662.3662.3662.5.5.1 |
qatmAal5UniThe UNI port alias associates with
this AAL5 interface.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.5.1.1 |
qatmAal5Aal5NameThe AAL5 port name.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.5.5.1.2 |
qatmAal5Aal5AliasThe alias for this AAL5 interface.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.5.5.1.3 |
qatmAal5AdminStatusThe desired state for this interface.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.5.5.1.4 |
qatmAal5TrapStatusIndicates whether the Link Up/Link
Down traps should be generated for this
interface.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.5.5.1.5 |
qatmAal5MtuSizeSet the largest PDU size for the AAL5 CPCS
layer that cen be processed by the AAL5 entity.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.5.1.6 |
qatmAal5RowStatusIndicate the entry's status.
(1..5 = add) 6 = delete.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.5.5.1.7 |
qatmTrafficDescriptorTableThe TrafficDescriptor table. SEQUENCE OF QatmTrafficDescriptorEntry .1.3.6.1.4.1.3662.3662.3662.5.6 |
qatmTrafficDescriptorEntryOne entry in the table. QatmTrafficDescriptorEntry .1.3.6.1.4.1.3662.3662.3662.5.6.1 |
qatmTrafficDescriptorAliasThe alias for this traffic descriptor.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.5.6.1.1 |
qatmTcTableThe ATM TC table. SEQUENCE OF QatmTcEntry .1.3.6.1.4.1.3662.3662.3662.5.7 |
qatmTcEntryOne entry in the table. QatmTcEntry .1.3.6.1.4.1.3662.3662.3662.5.7.1 |
qatmTcCellSyncThe number of cell sync occurred on
this Tc interface.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.5.7.1.1 |
qatmTcPortErrorsThe number of errors received on
this Tc interface.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.5.7.1.2 |
qatmTcDmaErrorsThe number of DMA errors received on
this Tc interface.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.5.7.1.3 |
qatmInvalidCellsThe number of invalid cellls received on
this Tc interface.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.5.7.1.4 |
qatmCellsForInactiveVccThe number of cellls received for an inactive Vcc.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.5.7.1.5 |
qatmAal5VccStatsTableThe ATM AAL5 Vcc Statistics table. SEQUENCE OF QatmAal5VccStatsEntry .1.3.6.1.4.1.3662.3662.3662.5.8 |
qatmAal5VccStatsEntryOne entry in the table. QatmAal5VccStatsEntry .1.3.6.1.4.1.3662.3662.3662.5.8.1 |
qatmAal5VccStatsInBytesThe number of bytes received by this AAL5 interface.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.5.8.1.1 |
qatmAal5VccStatsOutBytesThe number of bytes send by this AAL5 interface.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.5.8.1.2 |
qatmAal5VccStatsInSdusThe number of SDUs received by this AAL5 interface.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.5.8.1.3 |
qatmAal5VccStatsOutSdusThe number of SDUs send by this AAL5 interface.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.5.8.1.4 |
qatmAal5VccStatsErrsAndDiscardsThe number of error and discard packets received by this AAL5 interface.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.5.8.1.5 |
qatmAal5VccStatsLengthMismatchsThe number of length mismatched packets received by this AAL5 interface.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.5.8.1.6 |
qatmAal5VccStatsUserAbortsThe number of packets aborted by users.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.5.8.1.7 |
qatmAal5VccStatsPoolDepletedsThe number of packets aborted by users.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.5.8.1.8 |
qcraftPort OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.6 |
qcpStatusro Enumeration .1.3.6.1.4.1.3662.3662.3662.6.1 |
qcpBaudRateThe craft port command baud rate.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.6.2 |
qcpStopBitLengthrw Enumeration .1.3.6.1.4.1.3662.3662.3662.6.3 |
qcpParityrw Enumeration .1.3.6.1.4.1.3662.3662.3662.6.4 |
qcpDataBitsrw Enumeration .1.3.6.1.4.1.3662.3662.3662.6.5 |
qcpCharsSentrw INTEGER .1.3.6.1.4.1.3662.3662.3662.6.6 |
qcpCharsReceivedrw INTEGER .1.3.6.1.4.1.3662.3662.3662.6.7 |
qeventGroup OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.8 |
qEventConfigTableA list of Event System Configuration
Entries used for viewing / changing event
options SEQUENCE OF QEventConfigEntry .1.3.6.1.4.1.3662.3662.3662.8.1 |
qEventConfigEntryOne entry in the table QEventConfigEntry .1.3.6.1.4.1.3662.3662.3662.8.1.1 |
qEventConfigIndexA unique value for each event that has
been logged into one of the Event Logsro INTEGER .1.3.6.1.4.1.3662.3662.3662.8.1.1.1 |
qEventSeverityTypeA unique value which identifies each
Event Type (Severity).ro Enumeration .1.3.6.1.4.1.3662.3662.3662.8.1.1.2 |
qLogFileTypeA unique value which allows the
selection of the type of Log file
to Log events into.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.8.1.1.3 |
qLogOptionA flag which enables(1)/disables(2) the
logging feature of the Event Subsystemrw Enumeration .1.3.6.1.4.1.3662.3662.3662.8.1.1.4 |
qDisplayOptionA flag which enables(1)/disables(2) the
display feature of the Event Subsystemrw Enumeration .1.3.6.1.4.1.3662.3662.3662.8.1.1.5 |
qTrapOptionA flag which enables(1)/disables(2) the
Send Trap feature of the Event Subsystemrw Enumeration .1.3.6.1.4.1.3662.3662.3662.8.1.1.6 |
qEventSystemTableA list of Event Log Display
entries used for viewing the Logs. SEQUENCE OF QEventSystemEntry .1.3.6.1.4.1.3662.3662.3662.8.2 |
qEventSystemEntryOne entry in the table QEventSystemEntry .1.3.6.1.4.1.3662.3662.3662.8.2.1 |
qEventSystemIndexA unique value for each event that has
been logged into one of the Event Logsro INTEGER .1.3.6.1.4.1.3662.3662.3662.8.2.1.1 |
qEventSystemDateTimeThe time of day an event occurs
SNMP Community.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3662.3662.3662.8.2.1.2 |
qEventSystemTypeThis value will be used to identify the
Event Type to be displayedro Enumeration .1.3.6.1.4.1.3662.3662.3662.8.2.1.3 |
qEventSystemSubSystemThis value will be used to identify the
Event Type to be displayedro Enumeration .1.3.6.1.4.1.3662.3662.3662.8.2.1.4 |
qEventSystemID-NumberA unique value for each event that has
been logged into one of the Event Logsro INTEGER .1.3.6.1.4.1.3662.3662.3662.8.2.1.5 |
qEventSystemDescriptionA textual string containing the
Description of the occurred Event.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3662.3662.3662.8.2.1.6 |
qEventAlarmTableA list of Event Log Display
entries used for viewing the Logs. SEQUENCE OF QEventAlarmEntry .1.3.6.1.4.1.3662.3662.3662.8.3 |
qEventAlarmEntryOne entry in the table QEventAlarmEntry .1.3.6.1.4.1.3662.3662.3662.8.3.1 |
qEventAlarmIndexA unique value for each event that has
been logged into one of the Event Logsro INTEGER .1.3.6.1.4.1.3662.3662.3662.8.3.1.1 |
qEventAlarmDateTimeThe time of day an event occurs
SNMP Community.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3662.3662.3662.8.3.1.2 |
qEventAlarmTypeThis value will be used to identify the
Event Type to be displayedro Enumeration .1.3.6.1.4.1.3662.3662.3662.8.3.1.3 |
qEventAlarmSubSystemThis value will be used to identify the
Event Type to be displayedro Enumeration .1.3.6.1.4.1.3662.3662.3662.8.3.1.4 |
qEventAlarmID-NumberA unique value for each event that has
been logged into one of the Event Logsro INTEGER .1.3.6.1.4.1.3662.3662.3662.8.3.1.5 |
qEventAlarmDescriptionA textual string containing the
Description of the occurred Event.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3662.3662.3662.8.3.1.6 |
qextmib OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.9 |
qipExt OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.9.1 |
qipCircExtTableTable of IP circuit parameters SEQUENCE OF QipCircExtEntry .1.3.6.1.4.1.3662.3662.3662.9.1.1 |
qipCircExtEntryA circuits IP parameters QipCircExtEntry .1.3.6.1.4.1.3662.3662.3662.9.1.1.1 |
qipCircExtIndexAn index value which uniquely identifies
this circuit within the router. This may or may
not be related to the physical interface index.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.9.1.1.1.1 |
qipCircExtIfIndexAn index value which uniquely identifies
the local physical interface which this circuit
uses. This value identifies the same interface
identified by ifIndex in MIB-2.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.9.1.1.1.2 |
qipCircExtAdminStateEnable or disable the operation of IP
on the specified interface.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.9.1.1.1.3 |
qipCircExtOperStateThe operational state of the circuit. May
or may not be the same as administrative state.ro Enumeration .1.3.6.1.4.1.3662.3662.3662.9.1.1.1.4 |
qarpExt OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.9.2 |
qarpExtTtlThe lifetime of an ARP entry within the
router.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.9.2.1 |
qarpCircExtTableTable of ARP circuit parameters SEQUENCE OF QarpCircExtEntry .1.3.6.1.4.1.3662.3662.3662.9.2.2 |
qarpCircExtEntryA circuits ARP parameters QarpCircExtEntry .1.3.6.1.4.1.3662.3662.3662.9.2.2.1 |
qarpCircExtIndexAn index value which uniquely identifies
this circuit within the router. This may or may
not be related to the physical interface index.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.9.2.2.1.1 |
qarpCircExtIfIndexAn index value which uniquely identifies
the local physical interface which this circuit
uses. This value identifies the same interface
identified by ifIndex in MIB-2.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.9.2.2.1.2 |
qarpCircExtDoProxyEnable or disable ARP proxy responses
on the specified interface.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.9.2.2.1.3 |
qarpCircExtDoRespEnable or disable the sending of ARP
responses on specified circuit.ro Enumeration .1.3.6.1.4.1.3662.3662.3662.9.2.2.1.4 |
qripExt OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.9.3 |
qripExtAdminStateEnable or disable the operation of RIP
on all interfaces.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.9.3.1 |
qripExtUpdateTimeThe time between transmission of RIP
updates.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.9.3.2 |
qripCircExtTableTable of RIP circuit parameters SEQUENCE OF QripCircExtEntry .1.3.6.1.4.1.3662.3662.3662.9.3.3 |
qripCircExtEntryA circuits RIP parameters QripCircExtEntry .1.3.6.1.4.1.3662.3662.3662.9.3.3.1 |
qripCircExtIndexAn index value which uniquely identifies
this circuit within the router. This may or may
not be related to the physical interface index.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.9.3.3.1.1 |
qripCircExtIfIndexAn index value which uniquely identifies
the local physical interface which this circuit
uses. This value identifies the same interface
identified by ifIndex in MIB-2.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.9.3.3.1.2 |
qripCircExtTalkEnable or disable RIP transmission
on the specified interface.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.9.3.3.1.3 |
qripCircExtListenEnable or disable RIP reception
on the specified interface.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.9.3.3.1.4 |
qripCircExtPoisonEnable or disable operation of poison
reverse on the specified interface. If poison
is disabled, split-horzon operation is enabled.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.9.3.3.1.5 |
qmanufactRecord OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.10 |
qmrCheckSumThe checksum of the manufacturing record.ro Counter .1.3.6.1.4.1.3662.3662.3662.10.1 |
qmrBurnDateThe Date the manufacturing record was burned into flash.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3662.3662.3662.10.2 |
qmrBurnTimeThe time the manufacturing record was burned into flash.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3662.3662.3662.10.3 |
qmrOemNameThe OEM Name of the unit.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3662.3662.3662.10.4 |
qmrOemIDThe OEM ID of the unit.ro Counter .1.3.6.1.4.1.3662.3662.3662.10.5 |
qmrSerialNumberThe serial number of the unit.ro Counter .1.3.6.1.4.1.3662.3662.3662.10.6 |
qmrProductIDThe product ID of the unit.ro Enumeration .1.3.6.1.4.1.3662.3662.3662.10.7 |
qmrModelIDThe model ID of the unit.ro Enumeration .1.3.6.1.4.1.3662.3662.3662.10.8 |
qmrMacAddressThe MAC address of the unit.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.3662.3662.3662.10.9 |
qmrRepairTableList of Repairs performed on the unit.ro SEQUENCE OF QMrRepairEntry .1.3.6.1.4.1.3662.3662.3662.10.10 |
qmrRepairEntryList of Repairs performed on the unit.ro QMrRepairEntry .1.3.6.1.4.1.3662.3662.3662.10.10.1 |
qmrRepTypeThe Type of the repair.ro Enumeration .1.3.6.1.4.1.3662.3662.3662.10.10.1.1 |
qmrRepCodeThe code of the repair.ro Counter .1.3.6.1.4.1.3662.3662.3662.10.10.1.2 |
qmrRepDateThe date of the repair.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3662.3662.3662.10.10.1.3 |
qmrRepTimeThe time of the repair.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.3662.3662.3662.10.10.1.4 |
qethernet OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.11 |
qethernetCfgTableA list of Ethernet Configuration
entries. The maximum number is based
on the maximum interfaces. SEQUENCE OF QethernetCfgEntry .1.3.6.1.4.1.3662.3662.3662.11.1 |
qethernetCfgEntryThe Ethernet configuration information
for each Ethernet interface. QethernetCfgEntry .1.3.6.1.4.1.3662.3662.3662.11.1.1 |
qethernetMacAddressThe ethernet's physical address. An
six byte hexidecimal identifier, which
identifies the interface on the
physical media.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.3662.3662.3662.11.1.1.1 |
qethernetSpeedModeThe Ethernet chipset has five
available modes: (1)
100-MBPS-FULL-DUPLEX - sets ethernet
chipset to 100 mbps, full duplex mode;
(2) 10-MBPS-FULL-DUPLEX - sets ethernet
chipset to 10 mbps, full duplex mode;
(3) 100-MBPS-HALF-DUPLEX - sets
ethernet chipset to 100 mbps, half
duplex mode; (4) 10-MBPS-HALF-DUPLEX -
sets ethernet chipset to 10 mbps, half
duplex mode.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.11.1.1.2 |
qethernetEncapsulationThe flag which sets the ethernets
encapsulation type. 1 = Ethernet
Version 2 encapsulation; 2 = IEEE 802.3
encapsulation.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.11.1.1.3 |
qethernetAutoSenseThis object is used to negotiate the
speed/duplex. The default is set to
YES (1) - which negotiates from the
configured speed/duplex
(qethernetSpeedMode) or lower. When
set to NO (2) - this forces the
configured speed/duplex mode and will
not establish a link unless the other
end complies.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.11.1.1.4 |
qethernetNameThis object is used to???rw DisplayString .1.3.6.1.4.1.3662.3662.3662.11.1.1.5 |
qethernetCurrentSpeedModeThe Ethernet chipset has four
available modes or operation: (1)
100-MBPS-FULL-DUPLEX - sets ethernet
chipset to 100 mbps, full duplex mode;
(2) 10-MBPS-FULL-DUPLEX - sets ethernet
chipset to 10 mbps, full duplex mode;
(3) 100-MBPS-HALF-DUPLEX - sets
ethernet chipset to 100 mbps, half
duplex mode; (4) 10-MBPS-HALF-DUPLEX -
sets ethernet chipset to 10 mbps, half
duplex mode. This object will provide
the current speed/duplex achieved or
'No Link'.ro Enumeration .1.3.6.1.4.1.3662.3662.3662.11.1.1.6 |
qds1-e1 OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.12 |
qds1AutoClockSourceSearchingSelecting (1) YES will allow the
Policy Point unit to automatically
select the next available SPAN to
provide clock if the Primary Clock
Source fails. Selecting (2) NO
will instruct the unit to ignore all
clock source ports except the primary
source clock port.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.12.1 |
qds1PrimaryClockSourceIdentifies the unit's primary clock
source. The first SPAN port - (2)
SPAN-1; the second SPAN port - (3)
SPAN-2; the third SPAN port - (4)
SPAN-3; the fourth SPAN port - (5)
SPAN-4; the fifth SPAN port - (6)
SPAN-5; the sixth SPAN port - (7)
SPAN-6.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.12.2 |
qds1PrimaryClockSourceActionInstructs the Span unit to (1)
USE-CURRENT-SOURCE - stay with the
current source clock, or (2)
RETURN-TO-PRIMARY-SOURCE - restore the
clock to the primary clock source.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.12.3 |
qds1SpanCfgTableA list of Span Configuration entries.
The maximum number is based on the
maximum interfaces. SEQUENCE OF Qds1SpanCfgEntry .1.3.6.1.4.1.3662.3662.3662.12.4 |
qds1SpanCfgEntryThe DS1/E1 configuration information
for each DS1/E1 interface. Qds1SpanCfgEntry .1.3.6.1.4.1.3662.3662.3662.12.4.1 |
qds1LineCfgIndexA unique value which identifies a
DS1/E1 interface. This value 'should'
be made equal to the ifIndex, however,
this may not be the case, but will have
an internal association with the
ifEntry.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.12.4.1.1 |
qds1LineBuildOutThe Line Build Out specification for
the DS1/E1 interface. NOTE: (1)
represents not only the
LINE-BUILD-OUT-133-FT, but also 0 db
CSU.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.12.4.1.2 |
qds1ClockSourceEligibilityIdentifies whether the DS1/E1
interface is eligible to be the source
clock or not.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.12.4.1.3 |
qds1ClockModeIdentifies the clock's mode of
operation. Setting the clock mode to
(1) will allow the interface to act as
the slave to the network clock, and
setting the mode to (2) will allow the
unit's interface to provide the master
clock.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.12.4.1.4 |
qds1PerformanceMonitorIndicates whether or not performance
monitoring will be transmitted on this
interface. ENABLE (1) will transmit the
performance report according to the ANSI
T1.403-1995 standard. The performance
report contains performance information
for each of the four previous one-second
intervals.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.12.4.1.5 |
qds1ScramblerIndicates whether or not scrambling
of data is being generated on this
interface. ENABLE (1) will transmit the
scrambled data according to the ITU-T
0.191 Recommendation; DISABLE (2) will
not scramble the data. NOTE: A T1
interface will NOT support scrambling,
and therefore will be DISABLED.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.12.4.1.6 |
qds1SpanLoopBackCmdTableA list of Span Loopback Configuration
entries. The maximum number is based
on the maximum DS1/E1 interfaces. SEQUENCE OF Qds1SpanLoopBackCmdEntry .1.3.6.1.4.1.3662.3662.3662.12.5 |
qds1SpanLoopBackCmdEntryThe DS1/E1 loopback configuration
information for each DS1/E1 interface. Qds1SpanLoopBackCmdEntry .1.3.6.1.4.1.3662.3662.3662.12.5.1 |
qds1LineLoopbackIndexA unique value which identifies DS1/E1
interface. This value should be made
equal to the ifIndex.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.12.5.1.1 |
qds1LoopbackCommandThis object is used to (1) ACTIVATE
the configured loopback on the selected
interface (qds1LineIndex) of the
specified entity. If the dsx1OtherLoop
(4) has been configured (see rfc2495 -
dsx1LoopbackConfig), the supported
loopback is the Local Port Loopback
(LPL). The Local Port Loopback is used
to validate the ability to send and
receive data to the local DS1/E1
interface. LPL will use OAM flow to
verify data transfer. Normal OAM flows
are discontinued and an F4 OAM segment
flow is automatically started on VPI=0,
VCI=3 with a repeat timer of 1 second.
When the loopback is set to (2)
DEACTIVATE or comes to completion, the
previous OAM configuration flows are
restored.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.12.5.1.2 |
qds1LoopbackDurationThe value indicates the duration (in
SECONDS) that the Loopback will be in
process.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.12.5.1.3 |
qds1SpanLoopBackStatsTableA list of Span Loopback Statistics for
each entries. The maximum number is
based on the maximum DS1/E1
interfaces. SEQUENCE OF Qds1SpanLoopBackStatsEntry .1.3.6.1.4.1.3662.3662.3662.12.6 |
qds1SpanLoopBackStatsEntryThe DS1/E1 loopback statistics
information foreach DS1/E1 interface. Qds1SpanLoopBackStatsEntry .1.3.6.1.4.1.3662.3662.3662.12.6.1 |
qds1LineLoopbackStatIndexA unique value which identifies DS1/E1
interface. This value should be made
equal to the ifIndex.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.12.6.1.1 |
qds1OamSegmentSentThe total number of segment OAM
messages transmitted on the DS1/E1
interface in question for the duration
of the test.ro Counter .1.3.6.1.4.1.3662.3662.3662.12.6.1.2 |
qds1OamSegmentReceivedThe total number of segment OAM
messages received on the DS1/E1
interface in question for the duration
of the test.ro Counter .1.3.6.1.4.1.3662.3662.3662.12.6.1.3 |
qds1OamSegmentFailuresThe total number of segment OAM
messages timed out on the DS1/E1
interface in question for the duration
of the test.ro Counter .1.3.6.1.4.1.3662.3662.3662.12.6.1.4 |
qds10amRunnigTimeThis is running time for the loop back.ro Counter .1.3.6.1.4.1.3662.3662.3662.12.6.1.5 |
qconfigManager OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.13 |
qcmSystemFileThe name of the configuration file to edit.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.13.1 |
qcmConfigMaxEntriesThe number of Configuration entries.ro Counter .1.3.6.1.4.1.3662.3662.3662.13.2 |
qcmConfigTableA list of configuration file entries. The number of
entries is given by the value of qcmConfigMaxEntries. SEQUENCE OF QcmConfigEntry .1.3.6.1.4.1.3662.3662.3662.13.3 |
qcmConfigEntry QcmConfigEntry .1.3.6.1.4.1.3662.3662.3662.13.3.1 |
qcmTableIndexA unique value for each config file.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.13.3.1.1 |
qcmCurrentConfigFlag that indicates if this record is the current operational configuration.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.13.3.1.2 |
qcmActionOnConfigOperations that can be performed on the current table record.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.13.3.1.3 |
qcmFileAliasThe file alias name of the 'release' / 'configuration file' pair.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.13.3.1.4 |
qcmReleaseThe name of the release file (executable).rw DisplayString .1.3.6.1.4.1.3662.3662.3662.13.3.1.5 |
qcmConfigFileThe name of the configuration file.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.13.3.1.6 |
qcmBootSequenceThe boot sequence.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.13.3.1.7 |
qcmCreateDateTimeThe creation date and time of the configuration file.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.13.3.1.8 |
qcmOperSchedDateTimeThe date and time the configuration file became operational.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.13.3.1.9 |
qcmReleaseTableA list of Release file entries. SEQUENCE OF QcmReleaseEntry .1.3.6.1.4.1.3662.3662.3662.13.4 |
qcmReleaseEntry QcmReleaseEntry .1.3.6.1.4.1.3662.3662.3662.13.4.1 |
qcmReleaseIndexA unique value for each Release file.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.13.4.1.1 |
qcmReleaseNameThe name of a release file.ro DisplayString .1.3.6.1.4.1.3662.3662.3662.13.4.1.2 |
qcmReleaseVersionThe version of the release file.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.13.4.1.3 |
qcmConfigVerTableA list of Config file entries. SEQUENCE OF QcmConfigVerEntry .1.3.6.1.4.1.3662.3662.3662.13.5 |
qcmConfigVerEntry QcmConfigVerEntry .1.3.6.1.4.1.3662.3662.3662.13.5.1 |
qcmConfigVerIndexA unique value for each Config file.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.13.5.1.1 |
qcmConfigNameThe name of a Config file.ro DisplayString .1.3.6.1.4.1.3662.3662.3662.13.5.1.2 |
qcmConfigVersionThe version of the Config file.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.13.5.1.3 |
qcmConfigWorkWithMinThe minimum version of a Release file the Config file is compatable with.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.13.5.1.4 |
qcmConfigWorkWithMaxThe maximum version of a Release file the Config file is compatable with.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.13.5.1.5 |
qcmWhichFileWhich file to do SNMP GETs and SETS on.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.13.6 |
qcmUserBaseCfgFileThe name of the configuration file to edit.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.13.7 |
qcmUserNewCfgFileThe name of the new configuration file.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.13.8 |
qcmUserFileAliasThe file alias of the system file.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.13.9 |
qcmUserReleaseThe name of the release file.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.13.10 |
qcmUserBootSequenceThe boot sequence.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.13.11 |
qcmUserDateTimeThe date and time LDF is be scheduled.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.13.12 |
qcmStartConfigStart the configuration process.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.13.13 |
qcmStopConfigStop and Save the current configuration process.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.13.14 |
qcmStartViewConfigStart viewing a configuration file.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.13.15 |
qcmStopViewConfigStop viewing a configuration file.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.13.16 |
qcmCancelConfigCancel the current configuration process.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.13.17 |
qportManagement OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.15 |
qwesLpTableA list of Logical Port entries. SEQUENCE OF QwesLpEntry .1.3.6.1.4.1.3662.3662.3662.15.1 |
qwesLpEntryOne entry in the table. QwesLpEntry .1.3.6.1.4.1.3662.3662.3662.15.1.1 |
qwesLpNameDisplay the name for the Logical Port.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.15.1.1.1 |
qwesLpAliasEnter an alias for the Logical Port Inteface name that has significant
to your organization.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.15.1.1.2 |
qwesLpPhysicalInterfaceThe physical port that this Logical
Port associated.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.15.1.1.3 |
qwesLpDataLinkInterfaceThe data link port that this Logical
Port associated.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.15.1.1.4 |
qwesLpTrapStatusIndicates whether the Link Up/Link
Down traps should be generated for this
interface.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.15.1.1.5 |
qwesLpAdminStatusThe desired state of the interface set by management.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.15.1.1.6 |
qwesLpRowStatusThis object is used to create a new
row or modify or delete an existing row
in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.3662.3662.3662.15.1.1.7 |
qwesLifTableA list of Logical Interface entries. SEQUENCE OF QwesLifEntry .1.3.6.1.4.1.3662.3662.3662.15.2 |
qwesLifEntryOne entry in the table. QwesLifEntry .1.3.6.1.4.1.3662.3662.3662.15.2.1 |
qwesLifNameThe name for the Logical Port.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.15.2.1.1 |
qwesLifAliasThe alias for the logical inteface
name that has significant to your
organization.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.15.2.1.2 |
qwesLifLpIndexThe logical port (LP) number that this
logical interface has an association
with.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.15.2.1.3 |
qwesLifTrapStatusIndicates whether the Link Up/Link
Down traps should be generated for this
interface.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.15.2.1.4 |
qwesLifAdminStatusThe desired state of the interface set by management.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.15.2.1.5 |
qwesLifRowStatusThis object is used to create a new
row or modify or delete an existing row
in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.3662.3662.3662.15.2.1.6 |
qwesAtmArpTableA list of ATM ARP entries. SEQUENCE OF QWESLIFENTRY .1.3.6.1.4.1.3662.3662.3662.15.3 |
qwesAtmArpEntryOne entry in the table. QWESLIFENTRY .1.3.6.1.4.1.3662.3662.3662.15.3.1 |
qwesAtmArpLifIndexThe logical interfacne (LIF) number that this
ATM ARP entry has an association with.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.15.3.1.1 |
qip OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.16 |
qipPortTableA list of IP Port entries. SEQUENCE OF QWESIPENTRY .1.3.6.1.4.1.3662.3662.3662.16.1 |
qipPortEntryOne entry in the table. QWESIPENTRY .1.3.6.1.4.1.3662.3662.3662.16.1.1 |
qIpLpThe logical port number associated with this IP port.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.16.1.1.1 |
qIpAddrThe IP address of this IP Port.rw IpAddress .1.3.6.1.4.1.3662.3662.3662.16.1.1.2 |
qIpSubnetThe IP subnet ddress of this IP Port.rw IpAddress .1.3.6.1.4.1.3662.3662.3662.16.1.1.3 |
qIpMulticastIndicate whether or not multicast will be transmit on this interface.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.16.1.1.4 |
qIpRipStatusIndicate the RIP status.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.16.1.1.5 |
qIpArpTimeoutThe elapsed time of seconds before an ARP entry can be removed from the ARP table.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.16.1.1.6 |
qIpEncapIndicate the encapsulation type.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.16.1.1.7 |
qRipPortTableA list of IP Port entries. SEQUENCE OF QWESRIPENTRY .1.3.6.1.4.1.3662.3662.3662.16.2 |
qRipPortEntryOne entry in the table. QWESRIPENTRY .1.3.6.1.4.1.3662.3662.3662.16.2.1 |
qRipIpAddrThe IP address associated with this RIP Port.rw IpAddress .1.3.6.1.4.1.3662.3662.3662.16.2.1.1 |
qModeSelects what type of rip authentication to be used on the selected port.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.16.2.1.2 |
qAuthenticationThis is the password to be used, when password type is selected for above authentication.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.16.2.1.3 |
qSplitHorizon.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.16.2.1.4 |
qAdvertiseStaticRoutes.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.16.2.1.5 |
qAdvertiseIntf.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.16.2.1.6 |
qBroadcastType.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.16.2.1.7 |
qHoldDownInterval.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.16.2.1.8 |
qUpdatesSendWhat the router sends on this interface.
ripVersion1 implies sending RIP updates compliant
with RFC 1058. rip1Compatible implies
broadcasting RIP-2 updates using RFC 1058 route
subsumption rules. ripVersion2 implies
multicasting RIP-2 updates. ripV1Demand indicates
the use of Demand RIP on a WAN interface under RIP
Version 1 rules. ripV2Demand indicates the use of
Demand RIP on a WAN interface under Version 2 rules.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.16.2.1.9 |
qUpdatesReceiveThis indicates which version of RIP updates
are to be accepted. Note that rip2 and
rip1OrRip2 implies reception of multicast
packets.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.16.2.1.10 |
qDefaultRouteMetricThis variable indicates the metric that is to
be used for the default route entry in RIP updates
originated on this interface. A value of zero
indicates that no default route should be
originated; in this case, a default route via
another router may be propagated.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.16.2.1.11 |
qStaticArpTableA list of Static ARP entries. SEQUENCE OF QWESSTATICARPENTRY .1.3.6.1.4.1.3662.3662.3662.16.3 |
qStaticArpEntryOne entry in the table. QWESSTATICARPENTRY .1.3.6.1.4.1.3662.3662.3662.16.3.1 |
qStaticArpAddrThe IP address associated with this ARP entry.rw IpAddress .1.3.6.1.4.1.3662.3662.3662.16.3.1.1 |
qLifThe Logical Interface which uniquely identifies the local
interface which this ARP entry can be reached.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.16.3.1.2 |
qPhysTypeThe physical interface type associated with this ARP entry.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.16.3.1.3 |
qMacAddrThe physical address associated with this ARP entry.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.3662.3662.3662.16.3.1.4 |
qTypeDefines the ARP entry current status. Setting this entry to invalid(2)
has the effect of invalidating the correspding entry in the ARP table.
Setting this entry to valid(1) has the effect of installing the entry
in the ARP table and make it active.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.16.3.1.5 |
qipTtlThe time-to-live (in seconds) that a packet can live in
the network.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.16.4 |
qipRoutePriorityThe route priority indicates routing entry precedence in the system.
If RIP is selected, then all routing entries learned by RIP will have
higher priority then other entries. Also, if STATIC is selected, then
all routing entries which are static defined will have higher priority
then other entries.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.16.5 |
qipRipStatusThe RIP system flag.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.16.6 |
qigmp OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.16.7 |
qigmpInMsgsMessages received by the system.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.16.7.1 |
qigmpOutMsgsMessages transmitted by the system.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.16.7.2 |
qigmpInErrorsError messages received by the system.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.16.7.3 |
qigmpInReportsReported messages received by the system.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.16.7.4 |
qigmpInQueriesQuerries received by the system.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.16.7.5 |
qigmpInUnknownTypeUnkown messages received by the system.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.16.7.6 |
qIgmpStaticTableA list of Static IGMP entries. SEQUENCE OF QWESSTATICIGMPENTRY .1.3.6.1.4.1.3662.3662.3662.16.7.7 |
qIgmpStaticEntryOne entry in the table. QWESSTATICIGMPENTRY .1.3.6.1.4.1.3662.3662.3662.16.7.7.1 |
qIgmpStaticAddrThe IP address associated with this IGMP entry.rw IpAddress .1.3.6.1.4.1.3662.3662.3662.16.7.7.1.1 |
qIgmpLpThe logical port number associated with this IP port.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.16.7.7.1.2 |
qIgmpTypeDefines the IGMP entry current status. Setting this entry to invalid(2)
has the effect of invalidating the correspding entry in the IGMP table.
Setting this entry to valid(1) has the effect of installing the entry
in the IGMP table and make it active.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.16.7.7.1.3 |
qIgmpGroupTableA list of IGMP Group entries. SEQUENCE OF QWESGroupIgmpEntry .1.3.6.1.4.1.3662.3662.3662.16.7.8 |
qIgmpGroupEntryOne entry in the table. QWESGroupIgmpEntry .1.3.6.1.4.1.3662.3662.3662.16.7.8.1 |
qIgmpGroupAddrThe Multicast IP address associated with this IGMP entry.ro IpAddress .1.3.6.1.4.1.3662.3662.3662.16.7.8.1.1 |
qIgmpGroupLpThe logical port number associated with this IP port.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.16.7.8.1.2 |
qIgmpGroupMacAddrThe Multicast MAC address associated with the qIgmpGroupLp.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.3662.3662.3662.16.7.8.1.3 |
qIgmpGroupInstallTypeDefines how the multicast IP was installed. Static(1) entries are
specifically created by the user. Dynamic(2) entries are learned.
All others are unknown.ro Enumeration .1.3.6.1.4.1.3662.3662.3662.16.7.8.1.4 |
qarpInMsgsArp messages received by the system.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.16.13 |
qarpOutMsgsArp messages send by the system.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.16.14 |
qarpReqInMsgRequest Arp messages received by the system.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.16.15 |
qarpReqOutMsgsArp request messages send by the system.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.16.16 |
qarpRespInMsgsArp reply messages received by the system.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.16.17 |
qarpRespOutMsgsArp reply messages send by the system.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.16.18 |
qarpSendDiscardsArp discard messages send by the system.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.16.19 |
qarpSendTimeoutsArp timeout messages send by the system.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.16.20 |
qarpInResourceErrorsLack of resources Arp messages received by the system.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.16.21 |
qarpOutResourceErrorsLack of resources Arp messages send by the system.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.16.22 |
qRipStatsTableA list of Static ARP entries. SEQUENCE OF QWESRIPSTATSENTRY .1.3.6.1.4.1.3662.3662.3662.16.23 |
qRipStatsEntryOne entry in the table. QWESRIPSTATSENTRY .1.3.6.1.4.1.3662.3662.3662.16.23.1 |
qRipStatsAddrRip updates received by this system. IpAddress .1.3.6.1.4.1.3662.3662.3662.16.23.1.1 |
qrip2IfStatsUpdatesReceivesRip updates received by this system.ro Counter .1.3.6.1.4.1.3662.3662.3662.16.23.1.2 |
qmanagementGroup OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.17 |
qSysTimeSystem Time in GMT.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.17.1 |
qTftpTypeThe file upload type. 1 = operational, 2 = configrw INTEGER .1.3.6.1.4.1.3662.3662.3662.17.2 |
qTftpFileNameLocal filename to download into. If it exists, it WILL be overwritten.rw DisplayString .1.3.6.1.4.1.3662.3662.3662.17.3 |
qTftpServerIpAddressServer's IP addressrw IpAddress .1.3.6.1.4.1.3662.3662.3662.17.4 |
qTftpServerFileNameServer's filename to getrw DisplayString .1.3.6.1.4.1.3662.3662.3662.17.5 |
qTftpAdminStatusset to 1 to start TFTP download. 0 = ready for next download.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.17.6 |
qTftpOperStatus0=idle, 1=reading, 2=server IP error, 3=server filename error, 4 = donero INTEGER .1.3.6.1.4.1.3662.3662.3662.17.7 |
qTftpRxCountNumber of blocks receivedro INTEGER .1.3.6.1.4.1.3662.3662.3662.17.8 |
qTimeZoneCurrent time zone of the unit.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.17.9 |
qOamGroup OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.18 |
qoamGroupConfigTableA list of OAM group Configurable Parameters entries. SEQUENCE OF QOAMGROUPCONFIGENTRY .1.3.6.1.4.1.3662.3662.3662.18.1 |
qoamGroupConfigEntryOne entry in the table. QOAMGROUPCONFIGENTRY .1.3.6.1.4.1.3662.3662.3662.18.1.1 |
qoamGroupConfigIndexThe entry index of a particular group. Currently, there
are 6 groups define:
1) All circuit
2) All Uni1
3) All Uni2,
4) All Uni3,
5) All Vpl,
6) All Vcl.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.18.1.1.1 |
qoamGroupConfigAliasAlias name of a specified circuit or for all configured UNIs,
1=end-to-end, 2=segment-to-segment, 3=both.ro DisplayString .1.3.6.1.4.1.3662.3662.3662.18.1.1.2 |
qoamGroupConfigTypeThe type of OAM to be generated.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.18.1.1.3 |
qoamGroupConfigTransmitIntervalThe interval between OAM transmission in seconds.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.18.1.1.4 |
qoamGroupConfigS2SAlarmThresholdThe number of timed out segment-to-segment OAM replies
accumulated in sequence before an alarm is generated.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.18.1.1.5 |
qoamGroupConfigE2EAlarmThresholdThe number of timed out end-to-end OAM replies accumulated in
sequence before an alarm is generated.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.18.1.1.6 |
qoamGroupConfigStatusEnable/disable OAM operation.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.18.1.1.7 |
qoamCircuitConfigTableA list of OAM Configurable Parameters entries. SEQUENCE OF QOAMCIRCUITCONFIGENTRY .1.3.6.1.4.1.3662.3662.3662.18.2 |
qoamCircuitConfigEntryOne entry in the table. QOAMCIRCUITCONFIGENTRY .1.3.6.1.4.1.3662.3662.3662.18.2.1 |
qoamCircuitConfigIndexThe index for the selected circuit.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.18.2.1.1 |
qoamCircuitConfigTypeThe type of OAM to be generated.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.18.2.1.2 |
qoamCircuitConfigTransmitIntervalThe interval between OAM transmission in seconds.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.18.2.1.3 |
qoamCircuitConfigS2SAlarmThresholdThe number of timed out segment-to-segment OAM replies
accumulated in sequence before an alarm is generated.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.18.2.1.4 |
qoamCircuitConfigE2EAlarmThresholdThe number of timed out end-to-end OAM replies accumulated in
sequence before an alarm is generated.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.18.2.1.5 |
qoamCircuitConfigStatusEnable/disable OAM operation.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.18.2.1.6 |
qoamGroupControlTableA list of OAM Control Parameters entries. SEQUENCE OF QOAMGROUPCONTROLENTRY .1.3.6.1.4.1.3662.3662.3662.18.3 |
qoamGroupControlEntryOne entry in the table. QOAMGROUPCONTROLENTRY .1.3.6.1.4.1.3662.3662.3662.18.3.1 |
qoamGroupControlIndexThe index for the selected circuit.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.18.3.1.1 |
qoamGroupControlTypeThe type of OAM to be generated,
1=end-to-end, 2=segment-to-segment, 3=both.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.18.3.1.2 |
qoamGroupControlStatusInitiate or terminate OAM operation, 1=start and 2=stoprw Enumeration .1.3.6.1.4.1.3662.3662.3662.18.3.1.3 |
qoamCircuitControlTableA list of OAM Control Parameters entry. SEQUENCE OF QOAMCIRCUITCONTROLENTRY .1.3.6.1.4.1.3662.3662.3662.18.4 |
qoamCircuitControlEntryOne entry in the table. QOAMCIRCUITCONTROLENTRY .1.3.6.1.4.1.3662.3662.3662.18.4.1 |
qoamCircuitControlIndexThe index for the selected circuit.rw INTEGER .1.3.6.1.4.1.3662.3662.3662.18.4.1.1 |
qoamCircuitControlTypeThe type of OAM to be generated,
1=end-to-end, 2=segment-to-segment, 3=both.rw Enumeration .1.3.6.1.4.1.3662.3662.3662.18.4.1.2 |
qoamCircuitControlStatusInitiate or terminate OAM operation, 1=start and 2=stoprw Enumeration .1.3.6.1.4.1.3662.3662.3662.18.4.1.3 |
qoamStatsTableA list of OAM statistics entries. SEQUENCE OF QOAMSTATSENTRY .1.3.6.1.4.1.3662.3662.3662.18.5 |
qoamStatsEntryOne entry in the table. QOAMSTATSENTRY .1.3.6.1.4.1.3662.3662.3662.18.5.1 |
qoamStatsCircuitThe circuit id identifies the entry.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.18.5.1.1 |
qoamStatsVpiThe first half of the VPI/VCI pairs associated with the circuit id.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.18.5.1.2 |
qoamStatsVciThe second half of the VPI/VCI pairs associated with the circuit id.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.18.5.1.3 |
qoamStatsTypeThe type of OAM.ro Enumeration .1.3.6.1.4.1.3662.3662.3662.18.5.1.4 |
qoamStatsStatusThe current operational status of OAM on this circuit.
ON=OAMs being transmitted, OFF=OAMs not being transmitted.ro Enumeration .1.3.6.1.4.1.3662.3662.3662.18.5.1.5 |
qoamRequestTxThe total number of OAM requests transmitted.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.18.5.1.6 |
qoamRequestRxThe total number of OAM requests received.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.18.5.1.7 |
qoamReplyTxThe total number of OAM replies transmitted.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.18.5.1.8 |
qoamReplyRxThe total number of OAM replies received.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.18.5.1.9 |
qoamTimeoutsThe total number of OAM replies that were not received
before timeout.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.18.5.1.10 |
qoamMinRtThe minimum round trip time in seconds for receiving
OAM replies since the counters were last reset.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.18.5.1.11 |
qoamMaxRtThe maximun round trip time in seconds for receiving
OAM replies since the counters were last reset.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.18.5.1.12 |
qoamAveRtThe average round trip time in seconds for receiving
OAM replies since the counters were last reset.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.18.5.1.13 |
qoamOtherInErrsThe number of OAM received but discarded due to errors.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.18.5.1.14 |
qoamOtherOutErrsThe number of OAM can't transmitted due to errors.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.18.5.1.15 |
qoamCrc10InErrsThe number of OAM received but discarded due to crc-10
checksum error.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.18.5.1.16 |
qoamCrc10OutErrsThe number of OAM can't transmitted due to crc-10
checksum error.ro INTEGER .1.3.6.1.4.1.3662.3662.3662.18.5.1.17 |
qmiscGroup OBJECT IDENTIFIER .1.3.6.1.4.1.3662.3662.3662.19 |