QTECH-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for QTECH-MIB.
570
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
570 total| Object Name |
|---|
ntpEntStatusInPktsThe total number of NTP messages delivered to the
NTP entity from the transport service.ro Counter32 .1.3.6.1.2.1.197.1.2.13 |
ntpEntStatusOutPktsThe total number of NTP messages delivered to the
transport service by this NTP entity.ro Counter32 .1.3.6.1.2.1.197.1.2.14 |
ntpEntStatusBadVersionThe total number of NTP messages which were delivered
to this NTP entity and were for an unsupported NTP
version.ro Counter32 .1.3.6.1.2.1.197.1.2.15 |
ntpEntStatusProtocolErrorThe total number of NTP messages which were delivered
to this NTP entity and this entity was not able to
process due to an NTP protocol error.ro Counter32 .1.3.6.1.2.1.197.1.2.16 |
ntpEntConformance OBJECT IDENTIFIER .1.3.6.1.2.1.197.6 |
ntpEntCompliances OBJECT IDENTIFIER .1.3.6.1.2.1.197.6.1 |
ntpEntGroups OBJECT IDENTIFIER .1.3.6.1.2.1.197.6.2 |
newPortSecurityTableThe Port Security information table. SEQUENCE OF NewPortSecurityEntry .1.3.6.1.4.1.33.10.9.1 |
newPortSecurityEntryThe index of this table is port index. NewPortSecurityEntry .1.3.6.1.4.1.33.10.9.1.1 |
portSecurityPortIndexSecure Port Index.ro INTEGER .1.3.6.1.4.1.33.10.9.1.1.1 |
portSecurityStateenable or disable port security on this port.rw Enumeration .1.3.6.1.4.1.33.10.9.1.1.2 |
portSecurityStickyenable or disable port security sticky on this port.If enable it,the port converts all the dynamic secure
MAC addresses, including those that were dynamically learned before sticky learning was enabled,to sticky
secure MAC addresses and adds all sticky secure MAC addresses to the running configurationrw Enumeration .1.3.6.1.4.1.33.10.9.1.1.3 |
portSecurityMaxMacNumThe maximum number of security mac can be set or learned on the secure port.rw INTEGER .1.3.6.1.4.1.33.10.9.1.1.4 |
portSecurityCurMacNumThe number of the current security mac on the secure port.ro INTEGER .1.3.6.1.4.1.33.10.9.1.1.5 |
portSecurityCfgMacNumThe number of security mac can be set on the secure port.ro INTEGER .1.3.6.1.4.1.33.10.9.1.1.6 |
portSecurityVioMacNumThe violation number of mac received on the secure port.ro INTEGER .1.3.6.1.4.1.33.10.9.1.1.7 |
portSecurityAgingTimeThe aging time for secure address entries on the secure port.rw INTEGER .1.3.6.1.4.1.33.10.9.1.1.8 |
portSecurityAgingTypeThe aging type for secure address entries on the secure port.If you want to disable inactivity or static aging type,you can config default type.rw Enumeration .1.3.6.1.4.1.33.10.9.1.1.9 |
portSecurityVioModeThe violation mode of secure port mac count reach the threshold.The default mode is shutdown,if you want to disable violation mode,you can
config shutdown mode.rw Enumeration .1.3.6.1.4.1.33.10.9.1.1.10 |
portSecurityVioShutRecoveryTimeThe recovery time of violation shutdown mode, the recovery time range is <5-3600>, the value 0 is to cancel recovery time, the value <1-4> is not allowed to config.rw INTEGER .1.3.6.1.4.1.33.10.9.1.1.11 |
portSecurityVioRestrictRecoveryTimeThe recovery time of violation restrict mode, the recovery time range is <5-3600>, the value 0 is to cancel recovery time, the value <1-4> is not allowed to config.rw INTEGER .1.3.6.1.4.1.33.10.9.1.1.12 |
portSecurityVlanMaxNumTableTable of maximum mac number with vlan on security port, and the secure port must be on trunk mode. SEQUENCE OF PortSecurityVlanMaxNumEntry .1.3.6.1.4.1.33.10.9.2 |
portSecurityVlanMaxNumEntryAn entry in the port security maximum mac number with vlan table. PortSecurityVlanMaxNumEntry .1.3.6.1.4.1.33.10.9.2.1 |
portSecurityVlanPortIndexSecure Port Index.ro INTEGER .1.3.6.1.4.1.33.10.9.2.1.1 |
portSecurityVlanIndexThe vlan index on the secure port.ro INTEGER .1.3.6.1.4.1.33.10.9.2.1.2 |
portSecurityVlanMaxMacNumThe maximum number of security mac can be set or learned in the vlan on the secure port,
the maximum range is <1-4096>, the value 0 is to cancel maximum in this vlan,
and when you set the maximum number with one vlan the secure port must be on trunk mode.rw INTEGER .1.3.6.1.4.1.33.10.9.2.1.3 |
portSecurityVlanCurMacNumThe current number of security mac set or learned in the vlan on the secure port.ro INTEGER .1.3.6.1.4.1.33.10.9.2.1.4 |
portSecurityMacAddressTableTable of mac address on security port. SEQUENCE OF PortSecurityMacAddressEntry .1.3.6.1.4.1.33.10.9.3 |
portSecurityMacAddressEntryAn entry in the port security mac address table. PortSecurityMacAddressEntry .1.3.6.1.4.1.33.10.9.3.1 |
portSecurityMacAddressPortIndexSecure Port Index.ro INTEGER .1.3.6.1.4.1.33.10.9.3.1.1 |
portSecurityMacAddressVlanIndexThe vlan index on the secure port.When set mac address,the vlan index must be zero if the port is on access mode.ro INTEGER .1.3.6.1.4.1.33.10.9.3.1.2 |
portSecurityMacAddressSecure mac address on this secure portro OCTET STRING .1.3.6.1.4.1.33.10.9.3.1.3 |
portSecurityMacTypeThe type of mac address on the secure port.rw Enumeration .1.3.6.1.4.1.33.10.9.3.1.4 |
portSecurityMacStatusCurrent state of the mac address.rw Enumeration .1.3.6.1.4.1.33.10.9.3.1.5 |
antiArpscan OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.100 |
prohibitPortOID OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.100.1 |
recoverPortOID OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.100.2 |
prohibitIPOID OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.100.3 |
prohibitIPExceedSlimitOID OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.100.4 |
prohibitIPExceedHlimitOID OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.100.5 |
recoverIPOID OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.100.6 |
ipAddress OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.100.7 |
arpSpeedLimitOID OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.100.8 |
arpDiscardOID OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.100.9 |
recoverArpSpeedOID OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.100.10 |
recoverArpDiscardOID OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.100.11 |
fan OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.101 |
fanAbnormalOID OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.101.1 |
fanNormalOID OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.101.2 |
fanInsertOID OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.101.3 |
fanPullOutOID OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.101.4 |
power OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.102 |
powerAbnormalOID OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.102.1 |
powerNormalOID OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.102.2 |
powerInsertOID OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.102.3 |
powerPullOutOID OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.102.4 |
slotTemperature OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.103 |
slotTemperatureHigherOID OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.103.1 |
slotTemperatureLowerOID OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.103.2 |
dhcpsnooping OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.104 |
shutdownPort OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.104.1 |
noShutdownPort OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.104.2 |
addBlackhole OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.104.3 |
delBlackhole OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.104.4 |
rateViolation OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.105 |
rateViolationShutdownPort OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.105.1 |
rateViolationNoShutdownPort OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.105.2 |
portGroup OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.106 |
portGroupCreate OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.106.1 |
portGroupDelete OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.106.2 |
portGroupUpdate OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.106.3 |
macNotification OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.107 |
macAdd OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.107.1 |
macDelete OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.107.2 |
macMove OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.107.3 |
macCountLimit OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.108 |
macCountThreshold OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.108.1 |
efmOam OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.109 |
efmOamDiscoverySuccess OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.109.1 |
efmOamDiscoveryTimeout OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.109.2 |
efmOamLocalErrSymbolPeriodEvent OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.109.3 |
efmOamLocalErrFramePeriodEvent OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.109.4 |
efmOamLocalErrFrameEvent OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.109.5 |
efmOamLocalErrFrameSecondsSummaryEvent OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.109.6 |
efmOamLocalLinkFault OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.109.7 |
efmOamLocalCriticalEvent OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.109.8 |
efmOamRemoteErrSymbolPeriodEvent OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.109.9 |
efmOamRemoteErrFramePeriodEvent OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.109.10 |
efmOamRemoteErrFrameEvent OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.109.11 |
efmOamRemoteErrFrameSecondsSummaryEvent OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.109.12 |
efmOamRemoteLinkFault OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.109.13 |
efmOamRemoteCriticalEvent OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.109.14 |
efmOamRemoteDyingGasp OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.109.15 |
efmOamLoopBackSuccess OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.109.16 |
efmOamLoopBackExit OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.109.17 |
transceiverMonitor OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.110 |
transceiverMonitorAlarmEvent OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.110.1 |
transceiverMonitorWarnEvent OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.110.2 |
portSecurityTrap OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.111 |
portSecurityViolation OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.111.1 |
loopbackDetectionTrap OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.112 |
loopbackDetectionEvent OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.112.1 |
illegalDipPkt OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.113 |
illegalDipPktRcv OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.113.1 |
dyingGasp OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.114 |
dyingGaspEvent OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.114.1 |
vct OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.115 |
vctLinkDown OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.115.1 |
copyRunningConfig OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.116 |
copyRunningConfigEvent OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.116.1 |
systemStartReady OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.117 |
systemStartReadyEvent OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.117.1 |
boardFail OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.118 |
boardFailEvent OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.118.1 |
powerFail OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.119 |
powerFailEvent OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.119.1 |
mstp OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.120 |
mstpPortStateChanged OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.120.1 |
dcp OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.121 |
dcpDeny OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.121.1 |
userLoginLogout OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.122 |
consoleUserLogin OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.122.1 |
consoleUserLogout OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.122.2 |
telnetUserLogin OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.122.3 |
telnetUserLogout OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.122.4 |
sshUserLogin OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.122.5 |
sshUserLogout OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.122.6 |
erps OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.125 |
erpsSfDetected OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.125.1 |
erpsSfCleared OBJECT IDENTIFIER .1.3.6.1.4.1.3715.17.4.125.2 |
IMPORTSA value that represents a type of Internet address.
unknown(0) An unknown address type. This value MUST
be used if the value of the corresponding
InetAddress object is a zero-length string.
It may also be used to indicate an IP address
that is not in one of the formats defined
below.
ipv4(1) An IPv4 address as defined by the
InetAddressIPv4 textual convention.
ipv6(2) An IPv6 address as defined by the
InetAddressIPv6 textual convention.
ipv4z(3) A non-global IPv4 address including a zone
index as defined by the InetAddressIPv4z
textual convention.
ipv6z(4) A non-global IPv6 address including a zone
index as defined by the InetAddressIPv6z
textual convention.
dns(16) A DNS domain name as defined by the
InetAddressDNS textual convention.
Each definition of a concrete InetAddressType value must be
accompanied by a definition of a textual convention for use
with that InetAddressType.
To support future extensions, the InetAddressType textual
convention SHOULD NOT be sub-typed in object type definitions.
It MAY be sub-typed in compliance statements in order to
require only a subset of these address types for a compliant
implementation.
Implementations must ensure that InetAddressType objects
and any dependent objects (e.g., InetAddress objects) are
consistent. An inconsistentValue error must be generated
if an attempt to change an InetAddressType object would,
for example, lead to an undefined InetAddress value. In
particular, InetAddressType/InetAddress pairs must be
changed together if the address type changes (e.g., from
ipv6(2) to ipv4(1)). Enumeration .1.3.6.1.4.1.6339.100.16.4.4.1.3 |
ospfNetworkAreaAddressTableThe conceptual table of all of ospfNetworkAreaAddressEntry. SEQUENCE OF OspfNetworkAreaAddressEntry .1.3.6.1.4.1.6339.100.16.4.5 |
ospfNetworkAreaAddressEntryThe conceptual row for ospfNetworkAreaAddressTable. OspfNetworkAreaAddressEntry .1.3.6.1.4.1.6339.100.16.4.5.1 |
ospfNetworkAareaAddressNetworkArea address.ro IpAddress .1.3.6.1.4.1.6339.100.16.4.5.1.1 |
ospfNetworkAreaMaskNetworkArea mask.ro IpAddress .1.3.6.1.4.1.6339.100.16.4.5.1.2 |
ospfNetworkAreaAreaIdNetworkArea area ID.ro IpAddress .1.3.6.1.4.1.6339.100.16.4.5.1.3 |
ospfNetworkAreaStatusenabled(1), disabled(0).
valid/enable
invalid/disable
ValidStatus:
A simple status value for the object to create and destroy
a table entry. This is a simplified variant of RowStatus as it
supports only two values. Setting it to valid(1) creates an entry.
Setting it to invalid(0) destroys an entry.rw EnabledStatusPrivate .1.3.6.1.4.1.6339.100.16.4.5.1.4 |
sntpPollTimeThe interval for SNTP clients to send requests to NTP/SNTP.rw INTEGER .1.3.6.1.4.1.6339.100.17.1 |
sntpServerTableThe ipv4 sntp server configration table. SEQUENCE OF SntpServerEntry .1.3.6.1.4.1.6339.100.17.2 |
sntpServerEntryA set of configuration parameters for a ipv4 sntp server. SntpServerEntry .1.3.6.1.4.1.6339.100.17.2.1 |
sntpServerVersionThe version of ipv4 sntp server.ro INTEGER .1.3.6.1.4.1.6339.100.17.2.1.1 |
sntpServerAddressThe ipv4 address of the sntp server.ro IpAddress .1.3.6.1.4.1.6339.100.17.2.1.2 |
sntpServerStatusNow state.rw Enumeration .1.3.6.1.4.1.6339.100.17.2.1.3 |
sntpServer6TableThe ipv6 sntp server configration table. SEQUENCE OF SntpServer6Entry .1.3.6.1.4.1.6339.100.17.3 |
sntpServer6EntryA set of configuration parameters for a ipv6 sntp server. SntpServer6Entry .1.3.6.1.4.1.6339.100.17.3.1 |
sntpServer6VersionThe version of ipv6 sntp server.ro INTEGER .1.3.6.1.4.1.6339.100.17.3.1.1 |
sntpServer6AddressThe IP address of the ipv6 sntp server.ro Ipv6Address .1.3.6.1.4.1.6339.100.17.3.1.2 |
sntpServer6StatusNow state.rw Enumeration .1.3.6.1.4.1.6339.100.17.3.1.3 |
sntpTimeZone OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.17.4 |
sntpTimeZoneNameThe name of sntp time zone.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6339.100.17.4.1 |
sntpTimeZoneTypeThe type of sntp time zone.rw Enumeration .1.3.6.1.4.1.6339.100.17.4.2 |
sntpTimeZoneTimeThe interval time of sntp time zone.rw INTEGER .1.3.6.1.4.1.6339.100.17.4.3 |
sntpTimeZoneStatusnow state of sntp time zone.rw Enumeration .1.3.6.1.4.1.6339.100.17.4.4 |
urpfEnableGlobal Enable or disable the Unicast reverse path forwarding.rw Enumeration .1.3.6.1.4.1.6339.100.18.1 |
urpfPortTableThe URPF port configration table. SEQUENCE OF UrpfPortEntry .1.3.6.1.4.1.6339.100.18.2 |
urpfPortEntryThe index of this table is port index. UrpfPortEntry .1.3.6.1.4.1.6339.100.18.2.1 |
urpfPortIndexPort Index.ro INTEGER .1.3.6.1.4.1.6339.100.18.2.1.1 |
urpfPortModeConfigration of the URPF mode on the port.rw Enumeration .1.3.6.1.4.1.6339.100.18.2.1.2 |
urpfPortAllowDefaultAllow or not allow default route of URPF.rw Enumeration .1.3.6.1.4.1.6339.100.18.2.1.3 |
urpfPortStatusSetting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry.rw Enumeration .1.3.6.1.4.1.6339.100.18.2.1.4 |
dcscmdcEnableDcscm destination control multicast is disable or enablerw Enumeration .1.3.6.1.4.1.6339.100.20.1 |
dcscmdcAcl OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.20.2 |
dcscmdcAclNumberAcl number of Dcscm destination control multicast,the range is 6000
::= { dcscmdcAcl 1 }
dcscmdcAclSourceIp OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-create
STATUS current
DESCRIPTIONrw INTEGER .1.3.6.1.4.1.6339.100.20.7.1 |
dcscmscAclSourceIpSource ip address of acl entryrw IpAddress .1.3.6.1.4.1.6339.100.20.7.2 |
dcscmscAclSourceMaskSource Mask of acl entryrw IpAddress .1.3.6.1.4.1.6339.100.20.7.3 |
dcscmscAclDestinationIpDestination ip address of acl entry, the destination ip must be a valid multicast group address.rw IpAddress .1.3.6.1.4.1.6339.100.20.7.4 |
dcscmscAclDestinationMaskDestination Mask of acl entry, the destination mask should meet the request of muticast group address.rw IpAddress .1.3.6.1.4.1.6339.100.20.7.5 |
dcscmscAclPermitOrDenyacl entry permit or deny;0:deny; 1:permit; 2:del this aclrw Enumeration .1.3.6.1.4.1.6339.100.20.7.6 |
dcscmscPortbindingTabledcscm destination control multicast, Acl is binded to Port SEQUENCE OF DcscmscPortbindingEntry .1.3.6.1.4.1.6339.100.20.8 |
dcscmscPortbindingEntryThe index of this table is PortName DcscmscPortbindingEntry .1.3.6.1.4.1.6339.100.20.8.1 |
dcscmscPortbindingPortNameDcscm source control multicast,The Port Number of rulero INTEGER .1.3.6.1.4.1.6339.100.20.8.1.1 |
dcscmscPortbindingAclNumberDcscm source control multicast,The Acl number of rule ; 0 means to del the rule binded to portrw INTEGER (0|5000..5099) .1.3.6.1.4.1.6339.100.20.8.1.2 |
dcscmpcTabledcscm policy multicast table SEQUENCE OF DcscmpcEntry .1.3.6.1.4.1.6339.100.20.9 |
dcscmpcEntryThe index of this table is dcscmpcSourceIp,dcscmpcSourceMasklen,dcscmpcDestinationIp,dcscmpcDestinationMasklen DcscmpcEntry .1.3.6.1.4.1.6339.100.20.9.1 |
dcscmpcSourceIpsource ip address of policy multicastro IpAddress .1.3.6.1.4.1.6339.100.20.9.1.1 |
dcscmpcSourceMasklenMask length of source Ipro INTEGER .1.3.6.1.4.1.6339.100.20.9.1.2 |
dcscmpcDestinationIpDestination ip address of policy multicast,the destination ip must be a valid multicast group address.ro IpAddress .1.3.6.1.4.1.6339.100.20.9.1.3 |
dcscmpcDestinationMasklenMask length of destination Ipro INTEGER .1.3.6.1.4.1.6339.100.20.9.1.4 |
dcscmpccoscos value of policy multicast; between 0 and 7 ;8 means to del the policyrw INTEGER .1.3.6.1.4.1.6339.100.20.9.1.5 |
dcscm6dcEnabledcscm6 destination control multicast is disable or enablerw Enumeration .1.3.6.1.4.1.6339.100.21.1 |
dcscm6dcAcl OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.21.2 |
dcscm6dcAclNumberAcl number of Dcscm6 destination control multicast,the range is 9000
::= { dcscm6dcAcl 1 }
dcscm6dcAclSourceIp OBJECT-TYPE
SYNTAX Ipv6Address
MAX-ACCESS read-write
STATUS current
DESCRIPTIONrw INTEGER .1.3.6.1.4.1.6339.100.21.7.1 |
dcscm6scAclSourceIpSource ip address of acl entryrw Ipv6Address .1.3.6.1.4.1.6339.100.21.7.2 |
dcscm6scAclSourceMaskSource MaskLen of acl entryrw INTEGER .1.3.6.1.4.1.6339.100.21.7.3 |
dcscm6scAclDestinationIpDestination ip address of acl entry,the destination ip must be a valid multicast group address.rw Ipv6Address .1.3.6.1.4.1.6339.100.21.7.4 |
dcscm6scAclDestinationMaskDestination MaskLen of acl entry ,the mask length should meet the request of multicast group address.rw INTEGER .1.3.6.1.4.1.6339.100.21.7.5 |
dcscm6scAclPermitOrDenyacl entry permit or deny; 0:deny; 1:permit; 2:del this aclrw Enumeration .1.3.6.1.4.1.6339.100.21.7.6 |
dcscm6scPortbindingTabledcscm6 destination control multicast, Acl is binded to Port SEQUENCE OF Dcscm6scPortbindingEntry .1.3.6.1.4.1.6339.100.21.8 |
dcscm6scPortbindingEntryThe index of this table is PortName Dcscm6scPortbindingEntry .1.3.6.1.4.1.6339.100.21.8.1 |
dcscm6scPortbindingPortNameDcscm6 source control multicast,The Port Number of rulero INTEGER .1.3.6.1.4.1.6339.100.21.8.1.1 |
dcscm6scPortbindingAclNumberDcscm6 source control multicast,The Acl number of rule,0 means to del the rule binded to portrw INTEGER (0|8000..8099) .1.3.6.1.4.1.6339.100.21.8.1.2 |
dcscm6pcTabledcscm6 policy multicast table SEQUENCE OF Dcscm6pcEntry .1.3.6.1.4.1.6339.100.21.9 |
dcscm6pcEntryThe index of this table is dcscm6pcSourceIp,dcscm6pcSourceMask,dcscm6pcDestinationIp,dcscm6pcDestinationMask Dcscm6pcEntry .1.3.6.1.4.1.6339.100.21.9.1 |
dcscm6pcSourceIpsource ip address of policy multicastro Ipv6Address .1.3.6.1.4.1.6339.100.21.9.1.1 |
dcscm6pcSourceMaskSource MaskLen of policy multicastro INTEGER .1.3.6.1.4.1.6339.100.21.9.1.2 |
dcscm6pcDestinationIpDestination ip address of policy multicastro Ipv6Address .1.3.6.1.4.1.6339.100.21.9.1.3 |
dcscm6pcDestinationMaskDestination MaskLen of policy multicastro INTEGER .1.3.6.1.4.1.6339.100.21.9.1.4 |
dcscm6pccoscos value of policy multicast; between 0 and 7 ;8 means to del the policyrw INTEGER .1.3.6.1.4.1.6339.100.21.9.1.5 |
clusterv2Base OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.22.1 |
clusterv2BaseKeycluster run switch,set the key word only while the cluster is not running
and you should set it with set clusterv2BaseRun.rw OCTET STRING .1.3.6.1.4.1.6339.100.22.1.1 |
clusterv2BaseVlancluster run switch,set the Vlan only when the cluster is not running
and you should set it with set clusterv2BaseRun.
if get result is 0 that the cluser is not running!rw INTEGER .1.3.6.1.4.1.6339.100.22.1.2 |
clusterv2BaseRuncluster run switch,set the key word and vlan id or stop the cluster.rw Enumeration .1.3.6.1.4.1.6339.100.22.1.3 |
clusterv2BaseRoleThe role of the device.
none means cluster device isn't running.ro Enumeration .1.3.6.1.4.1.6339.100.22.1.4 |
clusterv2BaseVersionversion of cluster.ro OCTET STRING .1.3.6.1.4.1.6339.100.22.1.5 |
clusterv2BaseMaxNumberOfMembersThe maximum number of cluster members allowed in the
cluster. The command switch is considered as a cluster
member also.ro INTEGER .1.3.6.1.4.1.6339.100.22.1.6 |
clusterv2BaseMaxNumberOfSwitchesThe maximum number of cluster switches allowed in the
cluster. The Candidates include commander,candidate and member.ro INTEGER .1.3.6.1.4.1.6339.100.22.1.7 |
clusterv2Create OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.22.2 |
clusterv2CreateIPPoolip pool.Valid cluster ip-pool format like as 10.x.x.x,default is 10.254.254.1 .
if get result is 0 that the cluser is not running!
set it only on the device is not commander and should set it with set clusterv2CreateCmdrOperate.rw IpAddress .1.3.6.1.4.1.6339.100.22.2.1 |
clusterv2CreateNamecreate the clustername while create the cluster commander,
set it only on the device is not commander and should set it with set clusterv2CreateCmdrOperate.rw OCTET STRING .1.3.6.1.4.1.6339.100.22.2.2 |
clusterv2CreateCmdrOperateif set create ,operation is to build cluster according to clusterv2CreateClusterIPPool/clusterv2StatusClusterName.
if set destroy , operation is try to clear the IPPool and the ClusterName.
set create only on the device is not commander.
set destroy only on the device is commander.rw Enumeration .1.3.6.1.4.1.6339.100.22.2.3 |
clusterv2Status OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.22.3 |
clusterv2StatusClusterNameThe name of the cluster.Set only on the device is not commander.The default is NULL.rw OCTET STRING .1.3.6.1.4.1.6339.100.22.3.1 |
clusterv2StatusKeepalivecluster keepalive interval(3-30 second).
if get result is 0 that the cluser is not running!rw INTEGER .1.3.6.1.4.1.6339.100.22.3.2 |
clusterv2StatusLoss-countcluster the max(1-10) loss-count packet during the keeplive interval.
if get result is 0 that the cluser is not running!rw INTEGER .1.3.6.1.4.1.6339.100.22.3.3 |
clusterv2Commander OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.22.4 |
clusterv2CommanderAutoAddMemauto add mem switchrw Enumeration .1.3.6.1.4.1.6339.100.22.4.1 |
clusterv2MemberCountermember number on commander,read only on commander or will return 65535.ro Counter32 .1.3.6.1.4.1.6339.100.22.4.2 |
clusterv2MemberTableThis table contains one row per cluster member,
including the command switch,read only on commander. SEQUENCE OF Clusterv2MemberEntry .1.3.6.1.4.1.6339.100.22.4.3 |
clusterv2MemberEntryAn entry containing cluster management information
applicable to a particular cluster member. Clusterv2MemberEntry .1.3.6.1.4.1.6339.100.22.4.3.1 |
clusterv2MemberNumberAn arbitrary value which uniquely identifies the
cluster member switch number. It ranges from 1 to
clusterv2StatusMaxNumberOfMembers,read only on commander.ro INTEGER .1.3.6.1.4.1.6339.100.22.4.3.1.1 |
clusterv2MemberIpAddressThe management ip address of the member device.ro IpAddress .1.3.6.1.4.1.6339.100.22.4.3.1.2 |
clusterv2MemberOperStatusThe status of cluster management connectivity between
the command switch and a cluster member. Cluster management
connectivity is determined by the exchange of cluster
management messages between the command switch and a
cluster member.ro Enumeration .1.3.6.1.4.1.6339.100.22.4.3.1.3 |
clusterv2MemberMacAddressThe management MAC address of the member device.ro MacAddress .1.3.6.1.4.1.6339.100.22.4.3.1.4 |
clusterv2MemberHostNamero OCTET STRING .1.3.6.1.4.1.6339.100.22.4.3.1.5 |
clusterv2MemberDeviceTypedeviceType such as 5526S, 2008A etcro OCTET STRING .1.3.6.1.4.1.6339.100.22.4.3.1.6 |
clusterv2CandidateCountercandidate number on commander,read only on commander or will return 65535.ro Counter32 .1.3.6.1.4.1.6339.100.22.4.4 |
clusterv2CandidateTableThis table contains one row per cluster candidate,
A cluster candidate is a device that is currently
eligible to be added to the cluster of a command
switch. A device is eligible if it satisfies the
following conditions:
1. It start the cluster func.
2. It is in a same L2 LAN with commander switch
The entries in this table and the entries in
clusterMemberTable are mutually exclusive at all
times. That is, any device that is a cluster
member never shows up in the clusterCandidateTable
or is never a candidate at the same time . Also, any
candidate that shows up in clusterCandidateTable should not
appear in clusterMemberTable. SEQUENCE OF Clusterv2CandidateEntry .1.3.6.1.4.1.6339.100.22.4.5 |
clusterv2CandidateEntryAn entry pertaining to a single candidate device. Clusterv2CandidateEntry .1.3.6.1.4.1.6339.100.22.4.5.1 |
clusterv2CandidateIdThe candidate id.ro INTEGER .1.3.6.1.4.1.6339.100.22.4.5.1.1 |
clusterv2CandidateMacAddressThe MAC address of a device qualified to
to be a cluster member of the command switch
cluster.ro MacAddress .1.3.6.1.4.1.6339.100.22.4.5.1.2 |
clusterv2CandidateHostNamero OCTET STRING .1.3.6.1.4.1.6339.100.22.4.5.1.3 |
clusterv2CandidateDeviceTypero OCTET STRING .1.3.6.1.4.1.6339.100.22.4.5.1.4 |
clusterv2RebootMemOperation is to reboot the specified member.you can select more member one time,
the value connected with '-' or ';',the string len is 1-30 .set only on commander.rw OCTET STRING .1.3.6.1.4.1.6339.100.22.4.6 |
poeSystemEnableThe power inline global switch. Enable expresses it is turned on, while disable indicates that off.rw Enumeration .1.3.6.1.4.1.6339.100.26.1 |
poeMaxPowerThe power inline global available power whitch cannot be exceeded by the total power of all PDs.rw INTEGER .1.3.6.1.4.1.6339.100.26.2 |
poePoliceEnableThe power inline power mamagement switch. Enable expresses it is in priority-policy mode, while disable indicates that in first-in-first-get mode.rw Enumeration .1.3.6.1.4.1.6339.100.26.3 |
poeLegacyEnableThe power inline nonstandard PD detect switch. Enable expresses nonstandard PD can be detected, while disable indicates that cannot be detected.rw Enumeration .1.3.6.1.4.1.6339.100.26.4 |
poeDisconnectThe power inline disconnection mode.ro Enumeration .1.3.6.1.4.1.6339.100.26.5 |
poeCurrentPowerThe power inline current export power. It is a real time value.ro INTEGER .1.3.6.1.4.1.6339.100.26.6 |
poePortModeThe power inline power supply mode.ro Enumeration .1.3.6.1.4.1.6339.100.26.7 |
poeSoftwareVersionThe power inline software version.ro DisplayString .1.3.6.1.4.1.6339.100.26.8 |
poeHardwareVersionThe power inline hardware version.ro DisplayString .1.3.6.1.4.1.6339.100.26.9 |
poePortConfigTableThe power inline port configuration table SEQUENCE OF PoePortConfigEntry .1.3.6.1.4.1.6339.100.26.10 |
poePortConfigEntryThe power inline configuration in port. PoePortConfigEntry .1.3.6.1.4.1.6339.100.26.10.1 |
poePortIndexThe power inline port index. INTEGER .1.3.6.1.4.1.6339.100.26.10.1.1 |
poePortStatusThe power inline port switch. Enable expresses it is turned on, while disable indicates that off.enableAuto(1) turn on the
auto-mode,enableStatic(2) turn on the force-mode.rw Enumeration .1.3.6.1.4.1.6339.100.26.10.1.2 |
poePortPriorityThe power inline port priority.rw Enumeration .1.3.6.1.4.1.6339.100.26.10.1.3 |
poePortMaxPowerThe power inline port available power whitch cannot be exceeded by the connected PD.rw INTEGER .1.3.6.1.4.1.6339.100.26.10.1.4 |
poePortCurrentPowerThe power inline port used power. It is a real time value.ro INTEGER .1.3.6.1.4.1.6339.100.26.10.1.5 |
poePortCurrentCurrentThe power inline port export current. It is a real time value.ro INTEGER .1.3.6.1.4.1.6339.100.26.10.1.6 |
poePortCurrentVoltageThe power inline port export voltage. It is a real time value.ro INTEGER .1.3.6.1.4.1.6339.100.26.10.1.7 |
poePortPdStatusThe power inline detect status. on(1):PD is connected and natural powered, off(2):PD is not connected,
faulty(3):error, deny(4):power is low or high, force(5):force power.ro Enumeration .1.3.6.1.4.1.6339.100.26.10.1.8 |
poePortPdClassThe connected PD class of power inlinero INTEGER .1.3.6.1.4.1.6339.100.26.10.1.9 |
poeHighInrushEnableThe power inline high-inrush switch. Enable expresses it is turned on, while disable indicates that off.rw Enumeration .1.3.6.1.4.1.6339.100.26.11 |
qos2 OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.27.1 |
qos2MapCostoIntp OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.27.1.1 |
qos2MapCostoIntp1COS to IntPrio map,IntPrio1<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.1.1 |
qos2MapCostoIntp2COS to IntPrio map,IntPrio2<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.1.2 |
qos2MapCostoIntp3COS to IntPrio map,IntPrio1<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.1.3 |
qos2MapCostoIntp4COS to IntPrio map,IntPrio1<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.1.4 |
qos2MapCostoIntp5COS to IntPrio map,IntPrio1<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.1.5 |
qos2MapCostoIntp6COS to IntPrio map,IntPrio1<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.1.6 |
qos2MapCostoIntp7COS to IntPrio map,IntPrio1<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.1.7 |
qos2MapCostoIntp8COS to IntPrio map,IntPrio1<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.1.8 |
qos2MapCostoIntpStatusSetting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.1.9 |
qos2MapCostoDP OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.27.1.2 |
qos2MapCostoDP1COS to drop precedence map,Drop Precedence1<0-2>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.2.1 |
qos2MapCostoDP2COS to drop precedence map,Drop Precedence2<0-2>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.2.2 |
qos2MapCostoDP3COS to drop precedence map,Drop Precedence3<0-2>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.2.3 |
qos2MapCostoDP4COS to drop precedence map,Drop Precedence4<0-2>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.2.4 |
qos2MapCostoDP5COS to drop precedence map,Drop Precedence5<0-2>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.2.5 |
qos2MapCostoDP6COS to drop precedence map,Drop Precedence6<0-2>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.2.6 |
qos2MapCostoDP7COS to drop precedence map,Drop Precedence7<0-2>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.2.7 |
qos2MapCostoDP8COS to drop precedence map,Drop Precedence8<0-2>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.2.8 |
qos2MapCostoDPStatusSetting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.2.9 |
qos2MapDSCPtoDSCP OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.27.1.3 |
qos2MapDSCPtoDSCP1DSCP to DSCP map, DSCP1<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.3.1 |
qos2MapDSCPtoDSCP2DSCP to DSCP map, DSCP2<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.3.2 |
qos2MapDSCPtoDSCP3DSCP to DSCP map, DSCP3<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.3.3 |
qos2MapDSCPtoDSCP4DSCP to DSCP map, DSCP4<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.3.4 |
qos2MapDSCPtoDSCP5DSCP to DSCP map, DSCP5<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.3.5 |
qos2MapDSCPtoDSCP6DSCP to DSCP map, DSCP6<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.3.6 |
qos2MapDSCPtoDSCP7DSCP to DSCP map, DSCP7<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.3.7 |
qos2MapDSCPtoDSCP8DSCP to DSCP map, DSCP8<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.3.8 |
qos2MapDSCPtoDSCPoutDSCPDSCP to DSCP map, outDSCP<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.3.9 |
qos2MapDSCPtoDSCPStatusSetting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.3.10 |
qos2MapDSCPtoIntp OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.27.1.4 |
qos2MapDSCPtoIntp1DSCP to Intp map, DSCP1<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.4.1 |
qos2MapDSCPtoIntp2DSCP to Intp map, DSCP2<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.4.2 |
qos2MapDSCPtoIntp3DSCP to Intp map, DSCP3<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.4.3 |
qos2MapDSCPtoIntp4DSCP to Intp map, DSCP4<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.4.4 |
qos2MapDSCPtoIntp5DSCP to Intp map, DSCP5<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.4.5 |
qos2MapDSCPtoIntp6DSCP to Intp map, DSCP6<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.4.6 |
qos2MapDSCPtoIntp7DSCP to Intp map, DSCP7<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.4.7 |
qos2MapDSCPtoIntp8DSCP to Intp map, DSCP8<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.4.8 |
qos2MapDSCPtoIntpIntPriovalueDSCP to Intp map, IntPrio value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.4.9 |
qos2MapDSCPtoIntpStatusSetting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.4.10 |
qos2MapDSCPtoDP OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.27.1.5 |
qos2MapDSCPtoDP1DSCP to DP map, DSCP1<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.5.1 |
qos2MapDSCPtoDP2DSCP to DP map, DSCP2<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.5.2 |
qos2MapDSCPtoDP3DSCP to DP map, DSCP3<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.5.3 |
qos2MapDSCPtoDP4DSCP to DP map, DSCP4<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.5.4 |
qos2MapDSCPtoDP5DSCP to DP map, DSCP5<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.5.5 |
qos2MapDSCPtoDP6DSCP to DP map, DSCP6<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.5.6 |
qos2MapDSCPtoDP7DSCP to DP map, DSCP7<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.5.7 |
qos2MapDSCPtoDP8DSCP to DP map, DSCP8<0-63>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.5.8 |
qos2MapDSCPtoDPvalueDSCP to DP map, Drop Precedence value<0-2>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.5.9 |
qos2MapDSCPtoDPStatusSetting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.5.10 |
qos2MapExptoIntp OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.27.1.6 |
qos2MapExptoIntp1EXP to Intp map, IntPrio1 value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.6.1 |
qos2MapExptoIntp2EXP to Intp map, IntPrio2 value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.6.2 |
qos2MapExptoIntp3EXP to Intp map, IntPrio3 value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.6.3 |
qos2MapExptoIntp4EXP to Intp map, IntPrio4 value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.6.4 |
qos2MapExptoIntp5EXP to Intp map, IntPrio5 value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.6.5 |
qos2MapExptoIntp6EXP to Intp map, IntPrio6 value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.6.6 |
qos2MapExptoIntp7EXP to Intp map, IntPrio7 value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.6.7 |
qos2MapExptoIntp8EXP to Intp map, IntPrio8 value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.6.8 |
qos2MapExptoIntpStatusSetting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.6.9 |
qos2MapExptoDP OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.27.1.7 |
qos2MapExptoDP1EXP to DP map, Drop Precedence value<0-2>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.7.1 |
qos2MapExptoDP2EXP to DP map, Drop Precedence value<0-2>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.7.2 |
qos2MapExptoDP3EXP to DP map, Drop Precedence value<0-2>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.7.3 |
qos2MapExptoDP4EXP to DP map, Drop Precedence value<0-2>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.7.4 |
qos2MapExptoDP5EXP to DP map, Drop Precedence value<0-2>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.7.5 |
qos2MapExptoDP6EXP to DP map, Drop Precedence value<0-2>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.7.6 |
qos2MapExptoDP7EXP to DP map, Drop Precedence value<0-2>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.7.7 |
qos2MapExptoDP8EXP to DP map, Drop Precedence value<0-2>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.7.8 |
qos2MapExptoDPStatusSetting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.7.9 |
qos2MapIntptoDSCP OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.27.1.8 |
qos2MapIntptoDSCP1Intp to DSCP map, IntPrio value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.8.1 |
qos2MapIntptoDSCP2Intp to DSCP map, IntPrio value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.8.2 |
qos2MapIntptoDSCP3Intp to DSCP map, IntPrio value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.8.3 |
qos2MapIntptoDSCP4Intp to DSCP map, IntPrio value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.8.4 |
qos2MapIntptoDSCP5Intp to DSCP map, IntPrio value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.8.5 |
qos2MapIntptoDSCP6Intp to DSCP map, IntPrio value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.8.6 |
qos2MapIntptoDSCP7Intp to DSCP map, IntPrio value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.8.7 |
qos2MapIntptoDSCP8Intp to DSCP map, IntPrio value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.8.8 |
qos2MapIntptoDSCPStatusSetting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.8.9 |
qos2MapIntptoEXP OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.27.1.10 |
qos2MapIntptoEXP1Intp to EXP map, EXP value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.10.1 |
qos2MapIntptoEXP2Intp to EXP map, EXP value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.10.2 |
qos2MapIntptoEXP3Intp to EXP map, EXP value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.10.3 |
qos2MapIntptoEXP4Intp to EXP map, EXP value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.10.4 |
qos2MapIntptoEXP5Intp to EXP map, EXP value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.10.5 |
qos2MapIntptoEXP6Intp to EXP map, EXP value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.10.6 |
qos2MapIntptoEXP7Intp to EXP map, EXP value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.10.7 |
qos2MapIntptoEXP8Intp to EXP map, EXP value<0-7>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.10.8 |
qos2MapIntptoEXPStatusSetting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.10.9 |
qos2AggregatePolicy OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.27.1.11 |
qos2AggPolicyNameAggregate policy name<1-64>.rw DisplayString .1.3.6.1.4.1.6339.100.27.1.11.1 |
qos2AggPolicyCIRKbpsCIR(Committed Information Rate) Kbits per second <1-10000000>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.11.2 |
qos2AggPolicyCBSKbpsCBS(Committed Burst Size) Kbits per second <1-1000000>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.11.3 |
qos2AggPolicyPBSKbpsPBS(Peak Burst Size) Kbits per second <1-1000000>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.11.4 |
qos2AggPolicyPIRKbpsPIR(Peak Information Rate) Kbits per second <1-10000000>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.11.5 |
qos2AggPolicyConformActionconform-action transmit means send packets without any change when specified speed is not exceeded;
conform-action drop means drop packets when specified speed is not exceeded;
conform-action set-dscp-transmit specifies to mark down packet DSCP value according to policed-dscp mapping when specified speed is not exceeded;
conform-action set-prec-transmit specifies to mark down packet TOS value according to policed-dscp mapping when specified speed is not exceeded.
.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.11.6 |
qos2AggPolicyConformActionChangeValueIf conform-action is set-dscp-transmit(2),the value is between 0-63;
If conform-action is set-prec-transmit(3),the value is between 0-7;
If conform-action is set-cos-transmit(4),the value is between 0-7;
If conform-action is set-drop-precedence(5),the value is between 0-2;
If conform-action is set-internal-priority(6),the value is between 0-7;rw INTEGER .1.3.6.1.4.1.6339.100.27.1.11.7 |
qos2AggPolicyExceedActionconform-action transmit means send packets without any change when specified speed is not exceeded;
conform-action drop means drop packets when specified speed is not exceeded;
conform-action set-dscp-transmit specifies to mark down packet DSCP value according to policed-dscp mapping when specified speed is not exceeded;
conform-action set-prec-transmit specifies to mark down packet TOS value according to policed-dscp mapping when specified speed is not exceeded.
.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.11.8 |
qos2AggPolicyExceedActionChangeValueIf conform-action is set-dscp-transmit(2),the value is between 0-63;
If conform-action is set-prec-transmit(3),the value is between 0-7;
If conform-action is set-cos-transmit(4),the value is between 0-7;
If conform-action is set-drop-precedence(5),the value is between 0-2;
If conform-action is set-internal-priority(6),the value is between 0-7;rw INTEGER .1.3.6.1.4.1.6339.100.27.1.11.9 |
qos2AggPolicyViolateActionconform-action transmit means send packets without any change when specified speed is not exceeded;
conform-action drop means drop packets when specified speed is not exceeded;
conform-action set-dscp-transmit specifies to mark down packet DSCP value according to policed-dscp mapping when specified speed is not exceeded;
conform-action set-prec-transmit specifies to mark down packet TOS value according to policed-dscp mapping when specified speed is not exceeded.
.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.11.10 |
qos2AggPolicyViolateActionChangeValueIf conform-action is set-dscp-transmit(2),the value is between 0-63;
If conform-action is set-prec-transmit(3),the value is between 0-7;
If conform-action is set-cos-transmit(4),the value is between 0-7;
If conform-action is set-drop-precedence(5),the value is between 0-2;
If conform-action is set-internal-priority(6),the value is between 0-7;rw INTEGER .1.3.6.1.4.1.6339.100.27.1.11.11 |
qos2AggPolicyStatusSetting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.11.12 |
qos2ServicePolicyTableQoS service policy table. SEQUENCE OF Qos2ServicePolicyEntry .1.3.6.1.4.1.6339.100.27.1.12 |
qos2ServicePolicyEntryQoS service policy table. Qos2ServicePolicyEntry .1.3.6.1.4.1.6339.100.27.1.12.1 |
qos2PolicyMapNamePolicy map name<1-64>.ro DisplayString .1.3.6.1.4.1.6339.100.27.1.12.1.1 |
qos2ServicePolicyVlanListVlan list.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6339.100.27.1.12.1.2 |
qos2ServicePolicyStatusSetting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.12.1.3 |
qos2PortTable OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.27.1.13 |
qos2PortIndexport Indexrw INTEGER .1.3.6.1.4.1.6339.100.27.1.13.1 |
qos2PortTypethe relation between qosPortType and CLI:
0 mls qos trust {cos |dscp };
1 mls qos cos {<default-cos>};
2 service-policy input WORD;
3 mls qos queue {<queue id>} bandwidth {<MinBandwidth> <MaxBandwidth>};
4 mls qos queue algorithm {sp |wdrr |wrr };
5 mls qos queue wdrr weight {<Queue1 bandwidth> <Queue2 bandwidth> <Queue3 bandwidth> <Queue4 bandwidth> <Queue5 bandwidth> <Queue6 bandwidth> <Queue7 bandwidth> <Queue8 bandwidth>};
6 mls qos queue wrr weight {<Queue1 weight> <Queue2 weight> <Queue3 weight> <Queue4 weight> <Queue5 weight> <Queue6 weight> <Queue7 weight> <Queue8 weight>}.
According to the relation,when configurate qos with snmp,first set the qosPortType to the correct value to select CLI,
then set next CLI parameter.Fox example,set qos default cos is 5, first set qosPortType=1 ,then set qosPortCos to 5,
finally setting qosPortStatus to 1, trigger snmp-cache works.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.13.2 |
qos2PortCosport default cos valuerw INTEGER .1.3.6.1.4.1.6339.100.27.1.13.3 |
qos2PortTrustConfigure port trust.
cos(0),mls qos trust cos;
dscp(1),mls qos trust dscp.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.13.4 |
qos2PortPolicyThe corresponding CLI:service-policy input WORD.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6339.100.27.1.13.5 |
qos2PortQueueBandwidthThe corresponding CLI:mls qos queue {<queue id>} bandwidth {<MinBandwidth> <MaxBandwidth>}.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6339.100.27.1.13.6 |
qos2PortQueueAlgorithmThe corresponding CLI:mls qos queue algorithm {sp |wdrr |wrr }.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.13.7 |
qos2PortQueueWdrrThe corresponding CLI:mls qos queue wdrr weight {<Queue1 bandwidth> <Queue2 bandwidth> <Queue3 bandwidth> <Queue4 bandwidth> <Queue5 bandwidth> <Queue6 bandwidth> <Queue7 bandwidth> <Queue8 bandwidth>}.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6339.100.27.1.13.8 |
qos2PortQueueWrrThe corresponding CLI:mls qos queue wrr weight {<Queue1 weight> <Queue2 weight> <Queue3 weight> <Queue4 weight> <Queue5 weight> <Queue6 weight> <Queue7 weight> <Queue8 weight>}.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6339.100.27.1.13.9 |
qos2PortStatusSetting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.13.10 |
qos2ClassMapTable OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.27.1.14 |
qos2ClassMapNameclassmap namerw DisplayString .1.3.6.1.4.1.6339.100.27.1.14.1 |
qos2ClassMapType0 class-map <class-map-name>,index is classmapname;
1 match access-group <acl-index-or-name>,need qos2ClassMapAccessGroup cooperation;
2 match ip dscp <dscp-list>,need qos2ClassMapDscp cooperation;
3 match ip precedence <ip-precedence-list>,need qos2ClassMapIpPre cooperation;
4 match vlan <vlan-list>,need qos2ClassMapVlan cooperation;
5 match ipv6 dscp <dscp-list>,need qos2ClassMapV6Dscp cooperation;
7 match ipv6 flowlabel,need qos2ClassMapV6Flow cooperation;
8 match ipv6 access-group,need qos2ClassMapV6AccGroup cooperation;
9 match cos,need qos2ClassCos cooperation;
10 match exp <exp-list>,need qos2ClassMapExp cooperation.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.14.2 |
qos2ClassMapAccessGroupMatch specify access-group (name or number).
This object be configured only if qosClassMapType
in the same row is accessGroup(1).rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6339.100.27.1.14.3 |
qos2ClassMapDscpMatch specify Dscp.
This object be configured only if qosClassMapType
in the same row is dscp(2).rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6339.100.27.1.14.4 |
qos2ClassMapV6DscpMatch specify ipv6 Dscp.
This object be configured only if qosClassMapType
in the same row is v6dscp(5).rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6339.100.27.1.14.5 |
qos2ClassMapIpPreMatch specify Ip Precedence.
This object be configured only if qosClassMapType
in the same row is ippre(3).rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6339.100.27.1.14.6 |
qos2ClassMapV6AccGroupMatch specify Ipv6 Access-Group.
This object be configured only if qosClassMapType
in the same row is v6AccessGroup(8).rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6339.100.27.1.14.7 |
qos2ClassMapV6FlowMatch specify Ipv6 Flowlabel.
This object be configured only if qosClassMapType
in the same row is v6Flow(6).rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6339.100.27.1.14.8 |
qos2ClassMapVlanMatch specify Vlan list . At most 8 vlan id.
This object be configured only if qosClassMapType
in the same row is vlan(4).rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6339.100.27.1.14.9 |
qos2ClassMapCosMatch specify Cos .
This object be configured only if qosClassMapType
in the same row is cos(9).rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6339.100.27.1.14.10 |
qos2ClassMapExpMatch specify MPLS EXP.
This object be configured only if qosClassMapType
in the same row is Exp(10).rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6339.100.27.1.14.11 |
qos2ClassMapStatusSetting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.14.12 |
qos2PolicyTable OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.27.1.15 |
qos2PolicyNameQoS Policy namerw DisplayString .1.3.6.1.4.1.6339.100.27.1.15.1 |
qos2PolicyClassMapSpecify the classmap name.After a policy map is created, it can be associated to a class.
So, if you want the class map to match the policy map,please setting the qosPolicyType to 1,and then
setting the qosPolicyStatus to 1 .rw DisplayString .1.3.6.1.4.1.6339.100.27.1.15.2 |
qos2PolicyInsertClassMapSpecify the position of classmap name.rw DisplayString .1.3.6.1.4.1.6339.100.27.1.15.3 |
qos2PolicyTypethe relation between qosPolicyType and CLI:
0 policy-map <policy-map-name>;
1 class <class-map-name>;
2 policy <bits_per_second> <normal_burst_bytes> [pir <peak_rate_bps>] | <maximum_burst_bytes> [{conform-action ACTION | exceed-action ACTION | violate-action ACTION }];
3 policy aggregate <aggregate-policer-name>;
4 accounting.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.15.4 |
qos2PolicyCIRKbpsCIR(Committed Information Rate) Kbits per second <1-10000000>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.15.5 |
qos2PolicyCBSKbpsCBS(Committed Burst Size) Kbits per second <1-1000000>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.15.6 |
qos2PolicyPBSKbpsPBS(Peak Burst Size) Kbits per second <1-1000000>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.15.7 |
qos2PolicyPIRKbpsPIR(Peak Information Rate) Kbits per second <1-10000000>.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.15.8 |
qos2PolicyConformActionChangetransmit(0): means send packets without any change;
drop(1): means drop packets;
set-dscp-transmit(2): send packets and remark dscp value;
set-prec-transmit(3): send packets and remark ip-precedence value;
set-cos-transmit(4): send packets and remark cos value;
set-internal-priority(5):send packets and remark internal-priority value ;
set-drop-Precedence(6): send packets and remark drop-precedence value.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.15.9 |
qos2PolicyConformActionChangeValueIf action is set-dscp-transmit(2),the value is between 0-63;
else if action is set-prec-transmit(3),the value is between 0-7;
else if action is set-cos-transmit(4),the value is between 0-7;
else if action is set-internal-priority(5),the value is between 0-7;
else if action is set-drop-Precedence(6),the value is between 0-2.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.15.10 |
qos2PolicyExceedActionChangetransmit(0): means send packets without any change;
drop(1): means drop packets;
set-dscp-transmit(2): send packets and remark dscp value;
set-prec-transmit(3): send packets and remark ip-precedence value;
set-cos-transmit(4): send packets and remark cos value;
set-internal-priority(5):send packets and remark internal-priority value ;
set-drop-Precedence(6): send packets and remark drop-precedence value.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.15.11 |
qos2PolicyExceedActionChangeValueIf action is set-dscp-transmit(2),the value is between 0-63;
else if action is set-prec-transmit(3),the value is between 0-7;
else if action is set-cos-transmit(4),the value is between 0-7;
else if action is set-internal-priority(5),the value is between 0-7;
else if action is set-drop-Precedence(6),the value is between 0-2.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.15.12 |
qos2PolicyViolateActionChangetransmit(0): means send packets without any change;
drop(1): means drop packets;
set-dscp-transmit(2): send packets and remark dscp value;
set-prec-transmit(3): send packets and remark ip-precedence value;
set-cos-transmit(4): send packets and remark cos value;
set-internal-priority(5):send packets and remark internal-priority value ;
set-drop-Precedence(6): send packets and remark drop-precedence value.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.15.13 |
qos2PolicyViolateActionChangeValueIf action is set-dscp-transmit(2),the value is between 0-63;
else if action is set-prec-transmit(3),the value is between 0-7;
else if action is set-cos-transmit(4),the value is between 0-7;
else if action is set-internal-priority(5),the value is between 0-7;
else if action is set-drop-Precedence(6),the value is between 0-2.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.15.14 |
qos2PolicyAggregatePoliceraggregate-policer-name.
This object be configured only if qosPolicyType
in the same row is aggregatePolicer(3).rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6339.100.27.1.15.15 |
qos2PolicyStatusSetting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.15.16 |
qos2SetTable OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.27.1.16 |
qos2SetPolicyMapNameQoS Policy name.rw DisplayString .1.3.6.1.4.1.6339.100.27.1.16.1 |
qos2SetClassMapNameQoS class map name.rw DisplayString .1.3.6.1.4.1.6339.100.27.1.16.2 |
qos2SetTypeqos2SetType range:1,2,3,4,5,6
1 dscp Set IP DSCP (DiffServ CodePoints);
2 precedence Set IP precedence;
3 internal-priority Set internal-priority;
4 drop-precedence Set drop-precedence;
5 nexthop Set IP nexthop;
6 v6nextHop Set IPv6 nexthop;
7 cos Set CoS .rw Enumeration .1.3.6.1.4.1.6339.100.27.1.16.3 |
qos2SetDscpremark dscp for the classified flow.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.16.4 |
qos2SetPrecedenceremark ip precedence for classified flow.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.16.5 |
qos2SetInternalPriorityremark internal priority for classified flow.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.16.6 |
qos2SetDropPrecedenceremark drop precedence for classified flow.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.16.7 |
qos2SetDefaultPBR0:no set default PBR for classified flow;
1:set default PBR for classified flow.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.16.8 |
qos2SetVrfset vrf value for classified flow.rw INTEGER .1.3.6.1.4.1.6339.100.27.1.16.9 |
qos2SetnextHopset nexthop for classified flow.rw IpAddress .1.3.6.1.4.1.6339.100.27.1.16.10 |
qos2Setv6nextHopset IPv6 nexthop for classified flowrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6339.100.27.1.16.11 |
qos2SetCosremark cos for classified flowrw INTEGER .1.3.6.1.4.1.6339.100.27.1.16.12 |
qos2SetStatusSetting it to active(1) to creates an entry,setting it to destroy(2) to destroy an entry.rw Enumeration .1.3.6.1.4.1.6339.100.27.1.16.13 |
mabOnlineUserTableShow the information of MAB users. SEQUENCE OF MabOnlineUserEntry .1.3.6.1.4.1.6339.100.28.1 |
mabOnlineUserEntry MabOnlineUserEntry .1.3.6.1.4.1.6339.100.28.1.1 |
mabOnlineUserIndexThe index of MAB user. INTEGER .1.3.6.1.4.1.6339.100.28.1.1.1 |
mabOnlineUserMacThe mac of MAB user.ro DisplayString .1.3.6.1.4.1.6339.100.28.1.1.2 |
mabOnlineUserNameThe username of MAB user.ro DisplayString .1.3.6.1.4.1.6339.100.28.1.1.3 |
mabOnlineUserPortThe port for MAB user.ro DisplayString .1.3.6.1.4.1.6339.100.28.1.1.4 |
mabOnlineUserStateThe state of MAB user.ro DisplayString .1.3.6.1.4.1.6339.100.28.1.1.5 |
mabSetUserOfflineThe mac of user offline.rw DisplayString .1.3.6.1.4.1.6339.100.28.2 |
dot1xOnlineUserTableShow the information of dot1x users. SEQUENCE OF Dot1xOnlineUserEntry .1.3.6.1.4.1.6339.100.28.3 |
dot1xOnlineUserEntry Dot1xOnlineUserEntry .1.3.6.1.4.1.6339.100.28.3.1 |
dot1xOnlineUserIndexThe index of dot1x user. INTEGER .1.3.6.1.4.1.6339.100.28.3.1.1 |
dot1xOnlineUserMacThe mac of dot1x user.ro DisplayString .1.3.6.1.4.1.6339.100.28.3.1.2 |
dot1xOnlineUserNameThe name of dot1x user.ro DisplayString .1.3.6.1.4.1.6339.100.28.3.1.3 |
dot1xOnlineUserPortThe port for dot1x user.ro DisplayString .1.3.6.1.4.1.6339.100.28.3.1.4 |
dot1xOnlineUserPortVlanidThe vlan id of dot1x user.ro INTEGER .1.3.6.1.4.1.6339.100.28.3.1.5 |
dot1xOnlineUserPortMethodThe port method dot1x user.ro DisplayString .1.3.6.1.4.1.6339.100.28.3.1.6 |
dot1xOnlineUserPortControlThe port control for dot1x user.ro DisplayString .1.3.6.1.4.1.6339.100.28.3.1.7 |
dot1xOnlineUserStateThe state of dot1x user.ro DisplayString .1.3.6.1.4.1.6339.100.28.3.1.8 |
dot1xSetUserOfflineThe mac of user offline.rw DisplayString .1.3.6.1.4.1.6339.100.28.4 |
portMacCountLimitTableThe Port Mac Count Limit information table. SEQUENCE OF PortMacCountLimitEntry .1.3.6.1.4.1.6339.100.29.1 |
portMacCountLimitEntryThe index of this table is port index. PortMacCountLimitEntry .1.3.6.1.4.1.6339.100.29.1.1 |
portMacCountLimitPortIndexPort Index.ro INTEGER .1.3.6.1.4.1.6339.100.29.1.1.1 |
portMacCountLimitConfigNumConfigration of the maxmum dynamic mac can be learned on the port.rw INTEGER .1.3.6.1.4.1.6339.100.29.1.1.2 |
portMacCountLimitCurNumThe current number of the dynamic mac learned on the port.ro INTEGER .1.3.6.1.4.1.6339.100.29.1.1.3 |
portMacCountLimitDisableThe disable state of mac count limit on the port.the disable state can be set,but enable state is notrw Enumeration .1.3.6.1.4.1.6339.100.29.1.1.4 |
portMacCountLimitViolationModeThe violation mode of port mac count reach the threshold.The default mode is protect,if you want to disable violation mode,you can
config protect mode.rw Enumeration .1.3.6.1.4.1.6339.100.29.1.1.5 |
portMacCountLimitShutRecoveryTimeThe recovery time of violation shutdown mode, the recovery time range is <5-3600>, the value 0 is to cancel recovery time, the value <1-4> is not allowed to config.rw INTEGER .1.3.6.1.4.1.6339.100.29.1.1.6 |
ddmTranscDiagnosisTableA list of ddm transceiver diagnosis information. SEQUENCE OF DdmTranscDiagnosisEntry .1.3.6.1.4.1.6339.100.30.1 |
ddmTranscDiagnosisEntryentry for ddm transceiver diagnosis information. DdmTranscDiagnosisEntry .1.3.6.1.4.1.6339.100.30.1.1 |
ddmDiagnosisIfIndexinterface NO.ro INTEGER .1.3.6.1.4.1.6339.100.30.1.1.1 |
ddmDiagnosisTemperaturecurrent Temperature of the port,and the unit is C.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.2 |
ddmDiagTempHighAlarmThresholdHigh alarm threshold of Temperature.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.3 |
ddmDiagTempLowAlarmThresholdLow alarm threshold of Temperature.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.4 |
ddmDiagTempHighWarnThresholdHigh warn threshold of Temperature.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.5 |
ddmDiagTempLowWarnThresholdLow warn threshold of Temperature.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.6 |
ddmDiagnosisVoltagevoltage of the port,and the unit is V.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.7 |
ddmDiagVoltHighAlarmThresholdHigh alarm threshold of Voltage.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.8 |
ddmDiagVoltLowAlarmThresholdLow alarm threshold of Voltage.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.9 |
ddmDiagVoltHighWarnThresholdHigh warn threshold of Voltage.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.10 |
ddmDiagVoltLowWarnThresholdLow warn threshold of Voltage.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.11 |
ddmDiagnosisBiasbias of the port,the unit is mA.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.12 |
ddmDiagBiasHighAlarmThresholdHigh alarm threshold of Bias.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.13 |
ddmDiagBiasLowAlarmThresholdLow alarm threshold of Bias.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.14 |
ddmDiagBiasHighWarnThresholdHigh warn threshold of Bias.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.15 |
ddmDiagBiasLowWarnThresholdLow warn threshold of Bias.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.16 |
ddmDiagnosisRXPowerRXPower of the port,and the unit is dBM,if the value of RXPower is infinitesimal,then set it to '-'.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.17 |
ddmDiagRXPowerHighAlarmThresholdHigh alarm threshold of RXPower.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.18 |
ddmDiagRXPowerLowAlarmThresholdLow alarm threshold of RXPower.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.19 |
ddmDiagRXPowerHighWarnThresholdHigh warn threshold of RXPower.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.20 |
ddmDiagRXPowerLowWarnThresholdLow warn threshold of RXPower.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.21 |
ddmDiagnosisTXPowerTXPower of the port,and the unit is dBM,if the value of TXPoweris infinitesimal,then set it to '-'.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.22 |
ddmDiagTXPowerHighAlarmThresholdHigh alarm threshold of TXPower.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.23 |
ddmDiagTXPowerLowAlarmThresholdk=Low alarm threshold of TXPower.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.24 |
ddmDiagTXPowerHighWarnThresholdHigh warn threshold of TXPower.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.25 |
ddmDiagTXPowerLowWarnThresholdLow warn threshold of TXPower.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.26 |
ddmDiagSNSerial number of transceiver.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.27 |
ddmDiagVendorVendor of transceiver.ro DisplayString .1.3.6.1.4.1.6339.100.30.1.1.28 |
ddmTranscAlarmTableA list of ddm transceiver alarm information. SEQUENCE OF DdmTranscAlarmEntry .1.3.6.1.4.1.6339.100.30.2 |
ddmTranscAlarmEntryentry for ddm transceiver alarm information. DdmTranscAlarmEntry .1.3.6.1.4.1.6339.100.30.2.1 |
ddmAlarmIfIndexinterface NO.ro INTEGER .1.3.6.1.4.1.6339.100.30.2.1.1 |
ddmAlarmInfoddm transceiver alarm information.ro DisplayString .1.3.6.1.4.1.6339.100.30.2.1.2 |
priPppoeIaGlobalEnableEnable or disable the pppoe-ia function in the switch.rw Enumeration .1.3.6.1.4.1.6339.100.31.1 |
priPppoeIaSelfDefinedCircuitIDIf user does not configure the circuit-id of pppoe-ia explicitly on a port, then
the user can self-designed format to generate the circuit-id, the format options include
vlan, port, ID, self-designed string, the circuitId may be only one or any combination of them,
and is strictly generated according to the sequence of format options, the ID option includes
switch ID and remote-mac, but the user just select only one of them, also In the swtich ID, it
includes mac and hostname options, the user just select only one of two, the maximum length
of self-designed striing is 64. If user input NULL, then delete the last configuration.
For example, if select vlan ,ID(swtich-id(mac)), and string 'str' format,
the user input the string like as 'vlan id swtich-id mac string str'.rw DisplayString .1.3.6.1.4.1.6339.100.31.2 |
priPppoeIaTr101CircuitIDIf user does not configure the circuit-id of pppoe-ia explicitly on a port, then
the user can config Tr-101 format to generate the circuit-id, the format like follow
'identifier-string STRING option (sp|sv|pv|spv) delimiter WORD', the STRING can be any ascii
except space, and it max length is 47, the WORD must be one in (#|.|,|;|:|/|space).
If user input NULL, then delete the last configuration.
For example, if STRING is switch , option is spv and WORD is '/',
the user input the string like as 'identifier-string switch option spv delimiter /'.rw DisplayString .1.3.6.1.4.1.6339.100.31.3 |
priPppoeIaSelfDefinedRemoteIDIf user does not configure the remote-id of pppoe-ia explicitly on a port, then
the user can self-designed format to generate the remote-id, the format options include
mac,hostname and self-designed string, the remoteId may be only one or any combination of them,
and is strictly generated according to the sequence of format options,
the maximum length of self-designed striing is 64.
If user input the NULL, then delete the last configuration.
For example, if select hostname,mac,and string 'str' format,
the user input the string like as 'hostname mac string str'.rw DisplayString .1.3.6.1.4.1.6339.100.31.4 |
priPppoeIaDelimiterConfig pppoe-ia delimiter in circuitId and remoteId.
Default: the default delimiter of type TR-101 is space,
the default delimiter of type self-defined is '\0'rw Enumeration .1.3.6.1.4.1.6339.100.31.5 |
priPppoeIaCircuitIdFormatConfig pppoe-ia circuitId format.
Default: the default format of the circuitId's mac(if included) is hex, other is asciirw Enumeration .1.3.6.1.4.1.6339.100.31.6 |
priPppoeIaRemoteIdFormatConfig pppoe-ia remoteId format.
Default: the default format of the remoteId's mac(if included) is hex, other is asciirw Enumeration .1.3.6.1.4.1.6339.100.31.7 |
priPppoeIaPortTablePppoe-ia configuration in port. SEQUENCE OF PriPppoeIaEntry .1.3.6.1.4.1.6339.100.31.8 |
priPppoeIaEntryPppoe-ia configuration in port. PriPppoeIaEntry .1.3.6.1.4.1.6339.100.31.8.1 |
priPppoeIaPortIDThis value is port's ID. INTEGER .1.3.6.1.4.1.6339.100.31.8.1.1 |
priPppoeIaPortEnableEnable or disable the pppoe-ia function of the port in the switch. Default:0.rw Enumeration .1.3.6.1.4.1.6339.100.31.8.1.2 |
priPppoeIaPortCircuitIDConfig circuitId for the port. Default:NULL.rw DisplayString .1.3.6.1.4.1.6339.100.31.8.1.3 |
priPppoeIaPortRemoteIDConfig remoteId for the port. Default:NULL.rw DisplayString .1.3.6.1.4.1.6339.100.31.8.1.4 |
priPppoeIaPortTrustEnable or disable the pppoe-ia trust function of the port in the switch. Default:0rw Enumeration .1.3.6.1.4.1.6339.100.31.8.1.5 |
priPppoeIaPortVendorTagStripEnable or disable the pppoe-ia vendorTag strip function of the port in the switch. Default:0rw Enumeration .1.3.6.1.4.1.6339.100.31.8.1.6 |
macNotificationMibObjects OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.33.1 |
macNotificationGlobalObjects OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.33.1.1 |
macNotificationGlobalFeatureEnabledIndicates whether the MAC notification feature is currently
running in the device.
Setting this object to false(2) disables the MAC notification
feature globally thus disabling the feature at each interface.
Setting this object to true(1) will start the MAC notification
feature running in the device. If the feature is already
running, setting to true(1) has no effect. Once the MAC
notification is enabled, whether the feature is running at each
interface is controlled by the macNotificationIfConfigTable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6339.100.33.1.1.1 |
macNotificationNotificationIntervalThis object specifies the maximum interval of time between
macNotificationMacChangedNotifications being generated by the device.
If the value of macNotificationNotificationsEnabled is true(1), the
device will send out the generated macNotificationMacChangedNotifications
and archive the MAC change notification events in the
macNotificationHistoryTable. If the value of macNotificationNotificationEnabled is
false(2), the device will not send out the generated
macNotificationMacChangedNotifications but it will archive these events
in the macNotificationHistoryTable.
If the value of this object is equal to 0, the device will
generate macNotificationMacChangedNotifications and archive the MAC
change notification events in the macNotificationHistoryTable as soon as
there is MAC address learnt or removed by the device.
If the value of this object is greater than 0, the device will
wait for a period of time equal to the value of this object
before generate the macNotificationMacChangedNotifications and archive
the MAC change notification events in the macNotificationHistoryTable.ro Counter32 UNITS "seconds" .1.3.6.1.4.1.6339.100.33.1.1.2 |
macNotificationMacAddressesLearntIndicates the number of MAC addresses learnt by the
device.ro Counter32 .1.3.6.1.4.1.6339.100.33.1.1.3 |
macNotificationMacAddressesRemovedIndicates the number of MAC addresses removed from the
forwarding database.ro Counter32 .1.3.6.1.4.1.6339.100.33.1.1.4 |
macNotificationNotificationsEnabledIndicates whether macNotificationMacChangedNotification notifications
will or will not be sent when there are MAC addresses
learnt or removed from the device's forwarding database.
Disabling notifications does not prevent the MAC address
info from being added to the macNotificationHistoryTable.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6339.100.33.1.1.5 |
macNotificationNotificationsSentIndicates the number of macNotificationMacChangedNotifications sent out
by the device.ro Counter32 .1.3.6.1.4.1.6339.100.33.1.1.6 |
macNotificationHistTableMaxLengthThe upper limit on the number of entries that the
macNotificationHistoryTable may contain. A value of 0 will
prevent any history from being retained. When this
table is full, the oldest entry will be deleted and
a new one will be created.ro Counter32 UNITS "entries" .1.3.6.1.4.1.6339.100.33.1.1.7 |
macNotificationHistoryTableThis table will archive the MAC change notification events
generated by this device. The MAC change notification
events are archived here even if macNotificationMacChangesNotifications
are not actually sent. SEQUENCE OF MacNotificationHistoryEntry .1.3.6.1.4.1.6339.100.33.1.1.8 |
macNotificationHistoryEntryA MAC change notification message that was previously
generated by this device. Each entry is indexed by a message
index. MacNotificationHistoryEntry .1.3.6.1.4.1.6339.100.33.1.1.8.1 |
macNotificationHistIndexAn index that uniquely identifies a MAC change notification
event previously generated by the device. This index starts at
1 and increases by one when a MAC change notification is
generated. When it reaches the maximum value, the agent wraps
the value back to 1.ro Counter32 .1.3.6.1.4.1.6339.100.33.1.1.8.1.1 |
macNotificationHistMacChangedMsgThis object contains the information of a MAC change
notification event. It consists of several tuples packed
together in the format of '<tuple1><tuple2>...'.
Each tuple consist of 11 octets in the format of
'<operation><VLAN><MAC><dot1dBasePort>' where
<operation> is of size 1 octet and supports the following values
0 - End of MIB object.
1 - MAC learnt.
2 - MAC removed.
<VLAN> is VLAN number of the VLAN which the MAC address is
belonged to and has size of 2 octet.
<MAC> is the Layer2 Mac Address and has size of 6 octets.
<dot1dBasePort> is the value of dot1dBasePort for the
interface from which the MAC address is learnt and has size
of 2 octets.ro OCTET STRING .1.3.6.1.4.1.6339.100.33.1.1.8.1.2 |
macNotificationHistTimestampThe value of sysUpTime when the macNotificationMacChangedNotification
containing the information denoted by the macNotificationHistMacChangedMsg
object in this entry was generated.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.6339.100.33.1.1.8.1.3 |
macNotificationInterfaceObjects OBJECT IDENTIFIER .1.3.6.1.4.1.6339.100.33.1.2 |
macNotificationIfConfigTableThis table enables or disables the generation of notification
at each interface when MAC address is learnt or removed. SEQUENCE OF MacNotificationIfConfigEntry .1.3.6.1.4.1.6339.100.33.1.2.1 |
macNotificationIfConfigEntryEach entry contains the configuration for enabling the
MAC notification at each interface that supports this
feature. MacNotificationIfConfigEntry .1.3.6.1.4.1.6339.100.33.1.2.1.1 |
macNotificationMacAddrLearntEnableIndicates whether this interface is enabled to send
macNotificationMacChangedNotification when it learns a new MAC address. This
variable has no effect when the value of macNotificationGlobalFeatureEnabled
object is false(2).
Setting this object to true(1) enables the sending of
macNotificationMacChangedNotification when this interface learns a
new MAC address.
Setting this object to false(2) disables the sending
of macNotificationMacChangedNotification when this interface learns
a new MAC address.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6339.100.33.1.2.1.1.1 |
macNotificationMacAddrRemovedEnableIndicates whether this interface is enabled to send
macNotificationMacChangedNotification when a MAC address which it learnt
previously is removed from the forwarding table. This variable
has no effect when the value of macNotificationGlobalFeatureEnabled object
is false(2).
Setting this object to true(1) enables the sending of
macNotificationMacChangedNotification when a MAC address which this
interface learnt previously is removed from the forwarding
table.
Setting this object to false(2) disables the sending of
macNotificationMacChangedNotification when a MAC address which this
interface learnt previously is removed from the forwarding
table.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.6339.100.33.1.2.1.1.2 |
prieeePortTableA table containing current configuration information
for each port. SEQUENCE OF PrieeePortEntry .1.3.6.1.4.1.6339.100.34.1 |
prieeePortEntryeee configuration in port PrieeePortEntry .1.3.6.1.4.1.6339.100.34.1.1 |
eeePortIndexThe eee configuration port index. INTEGER .1.3.6.1.4.1.6339.100.34.1.1.1 |
eeePortStatusThe eee config. Enable expresses it is turned on, while disable indicates that off.rw Enumeration .1.3.6.1.4.1.6339.100.34.1.1.2 |
portRateLimitTableThe Port Receiving Packets Rate Limit information table. SEQUENCE OF PortRateLimitEntry .1.3.6.1.4.1.6339.100.35.1 |
portRateLimitEntryThe index of this table is port index. PortRateLimitEntry .1.3.6.1.4.1.6339.100.35.1.1 |
portRateLimitPortIndexPort Index.ro INTEGER .1.3.6.1.4.1.6339.100.35.1.1.1 |
portRateLimitConfigBroadcastNumConfigration of the max receiving rate of broadcast packets on the port,the value range is <200-2000000>.
The value 0 means disable the rate limit of broadcast packets.
the value <1-199> is not allowed to config.rw INTEGER .1.3.6.1.4.1.6339.100.35.1.1.2 |
portRateLimitCurBroadcastNumThe current receiving rate of broadcast packets on the port.ro INTEGER .1.3.6.1.4.1.6339.100.35.1.1.3 |
portRateLimitConfigMulticastNumConfigration of the max receiving rate of multicast packets on the port,the value range is <200-2000000>.
The value 0 means disable the rate limit of multicast packets.
the value <1-199> is not allowed to config.rw INTEGER .1.3.6.1.4.1.6339.100.35.1.1.4 |
portRateLimitCurMulticastNumThe current receiving rate of Multicast packets on the port.ro INTEGER .1.3.6.1.4.1.6339.100.35.1.1.5 |
portRateLimitConfigUnicastNumConfigration of the max receiving rate of unicast packets on the port,the value range is <200-2000000>.
The value 0 means disable the rate limit of unicast packets.
the value <1-199> is not allowed to config.rw INTEGER .1.3.6.1.4.1.6339.100.35.1.1.6 |
portRateLimitCurUnicastNumThe current receiving rate of unicast packets on the port.ro INTEGER .1.3.6.1.4.1.6339.100.35.1.1.7 |
portRateLimitConfigAllNumConfigration of the max receiving rate of all packets on the port,the value range is <200-2000000>.
The value 0 means disable the rate limit of all packets.
the value <1-199> is not allowed to config.rw INTEGER .1.3.6.1.4.1.6339.100.35.1.1.8 |
portRateLimitCurAllNumThe current receiving rate of all packets on the port.ro INTEGER .1.3.6.1.4.1.6339.100.35.1.1.9 |
portRateLimitPacketsTypeWhich type of receiving packets that rate limit is set.
0:none, 1:broadcast, 2:multicast, 3:unicast, 4:all,
5:broadcast+multicast, 6:broadcast+unicast, 7:multicast+unicast.
8:broadcast+all, 9:multicast+all, 10:unicast+all, 11:broadcast+multicast+all,
12:broadcast+unicast+all, 13:multicast+unicast+all, 14:broadcast+multicast+unicast,
15:broadcast+multicast+unicast+allro INTEGER .1.3.6.1.4.1.6339.100.35.1.1.10 |
portRateLimitViolationModeThe violation mode of port receiving packets rate reach the threshold.The default mode is no violation actions.rw Enumeration .1.3.6.1.4.1.6339.100.35.1.1.11 |
portRateLimitShutRecoveryTimeThe recovery time of violation shutdown mode, the recovery time range is <0-86400>,
the value 0 means the port cann't be recovery forever, the default value is 300.rw INTEGER .1.3.6.1.4.1.6339.100.35.1.1.12 |
macBlackholeTableA table containing current configuration information for each mac in vlan`s status. SEQUENCE OF MacBlackholeEntry .1.3.6.1.4.1.6339.100.36.1 |
macBlackholeEntryThie entry is control the mac add to blackhole or delete from blackhole. MacBlackholeEntry .1.3.6.1.4.1.6339.100.36.1.1 |
macAddressInVlanIDThis value is the mac address in vlan. INTEGER .1.3.6.1.4.1.6339.100.36.1.1.1 |
macAddressThis value is mac address. OCTET STRING .1.3.6.1.4.1.6339.100.36.1.1.2 |
macTypeControl the mac from both(0)/source(1)/destination(2).Default both(0).rw Enumeration .1.3.6.1.4.1.6339.100.36.1.1.3 |
macStatuscreat(0) the mac to blackhole,or destroy(2) the mac from blackhole.active(1)the mac in blackholerw Enumeration .1.3.6.1.4.1.6339.100.36.1.1.4 |
cableTableA list of port entries. SEQUENCE OF priCableEntry .1.3.6.1.4.1.6339.100.37.1 |
priCableEntryA port entry containing port information,
status, and control. priCableEntry .1.3.6.1.4.1.6339.100.37.1.1 |
CableLengthInfoCable Length Info.ro DisplayString .1.3.6.1.4.1.6339.100.37.1.1.1 |
priMrppRingTableThe MRPP Ring information table. SEQUENCE OF priMrppRingEntry .1.3.6.1.4.1.6339.100.38.1 |
priMrppRingEntryThe index of this table is RING index. priMrppRingEntry .1.3.6.1.4.1.6339.100.38.1.1 |
mrppRingIndexmrpp ring Index<1-4096>.ro INTEGER .1.3.6.1.4.1.6339.100.38.1.1.1 |
mrppRingNodeModemrpp ring node mode:MASTER:1,TRANSIT:0.ro INTEGER .1.3.6.1.4.1.6339.100.38.1.1.2 |
mrppRingNodeStatemrpp ring node state:
IDLE: 0,
COMPLETE: 1,
FAILED: 2,
LINKS_UP: 3,
LINKS_DOWN: 4,
PRE_FORWARDING: 5.ro INTEGER .1.3.6.1.4.1.6339.100.38.1.1.3 |
mrppRingStatusmrpp ring status:enable:1,disable:0.ro INTEGER .1.3.6.1.4.1.6339.100.38.1.1.4 |
mrppRingPriPortNamering's traffic primary port name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6339.100.38.1.1.5 |
mrppRingPriPortBlockStatering's traffic primary port block state:BLOCK:1,UNBLOCK:0.ro INTEGER .1.3.6.1.4.1.6339.100.38.1.1.6 |
mrppRingSecPortNamering's traffic secondary port name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.6339.100.38.1.1.7 |
mrppRingSecPortBlockStatering's traffic secondary port block state:BLOCK:1,UNBLOCK:0.ro INTEGER .1.3.6.1.4.1.6339.100.38.1.1.8 |
dnsEnableEnable or disable dns dynamic domain resolving.rw Enumeration .1.3.6.1.4.1.9600.1.2.10.1 |
dnsServerTableThe dns server list table which consists of a sequence of 'dnsServerEntry' items which describe
the configured dns server IP information. SEQUENCE OF DnsServerEntry .1.3.6.1.4.1.9600.1.2.10.2 |
dnsServerEntryAn entry in the dnsServerTable containing the dns server IP. DnsServerEntry .1.3.6.1.4.1.9600.1.2.10.2.1 |
dnsServerInetAddrTypeThe IP address type of dnsServerEntry. This value applies to dnsServerIpAddr. InetAddressType .1.3.6.1.4.1.9600.1.2.10.2.1.1 |
dnsServerIpAddrThe dns server IP address with 'dnsServerInetAddrType' to indicate the IP address type(IPv4 or IPv6).ro InetAddress .1.3.6.1.4.1.9600.1.2.10.2.1.2 |
dnsServerPriorityCurrent Priority of the dns server.rw INTEGER .1.3.6.1.4.1.9600.1.2.10.2.1.3 |
dnsServerStatusCurrent state of the dns server.rw Enumeration .1.3.6.1.4.1.9600.1.2.10.2.1.4 |
dnsDomainSuffixTableThe dns domain suffix table which consists of a sequence of 'dnsDomainSuffixEntry' items which describe
the configured dns domain suffix information. SEQUENCE OF DnsDomainSuffixEntry .1.3.6.1.4.1.9600.1.2.10.3 |
dnsDomainSuffixEntryAn entry in the dnsDomainSuffixTable containing the dns domain suffix. DnsDomainSuffixEntry .1.3.6.1.4.1.9600.1.2.10.3.1 |
dnsDomainSuffixThe dns domain suffix(e.g. commpany.com).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9600.1.2.10.3.1.1 |
dnsDomainSuffixStatusCurrent state of the dns domain suffix.rw Enumeration .1.3.6.1.4.1.9600.1.2.10.3.1.2 |
dnsDynHostTableThe dns dynamic host table which consists of a sequence of 'dnsDynHostEntry' items which describe
the resolved dns dynamic host information. SEQUENCE OF DnsDynHostEntry .1.3.6.1.4.1.9600.1.2.10.4 |
dnsDynHostEntryAn entry in the dnsDynHostTable containing the dns dynamic host information. DnsDynHostEntry .1.3.6.1.4.1.9600.1.2.10.4.1 |
dnsDynHostIndexIndex of position in the cache INTEGER .1.3.6.1.4.1.9600.1.2.10.4.1.1 |
dnsDynHostNameThe dns dynamic host name(e.g. www.sina.com.cn).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.9600.1.2.10.4.1.2 |
dnsDynHostIpAddrThe dns dynamic host's IP address with 'dnsDynHostInetAddrType' to indicate the IP address type(IPv4 or IPv6).ro InetAddress .1.3.6.1.4.1.9600.1.2.10.4.1.3 |
dnsDynHostTtlThe dns dynamic host's living time(seconds).ro INTEGER .1.3.6.1.4.1.9600.1.2.10.4.1.4 |