PRVT-RIP-EXTENSION-MIB
Imported Objects
Objects
10 total| Object Name |
|---|
routingProtocols OBJECT IDENTIFIER .1.3.6.1.4.1.738.1.6.4 |
prvtRIPExtensionMibThe RIP extension MIB module contains additional information, needed to control the RIP protocol, that is not found in the standard RFC MODULE-IDENTITY .1.3.6.1.4.1.738.1.6.4.1 |
ripExtension OBJECT IDENTIFIER .1.3.6.1.4.1.738.1.6.4.1.1 |
ripEnableThis object enables/disables the RIP process in the switchrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.738.1.6.4.1.1.1 |
ripRedistributeTableThe table represents the routing protocols, redistributed into the RIP routing domain. Creation of conceptual row in the table starts the redistribution of the specified protocol, which would lead to the injection of routing information from that protocol into RIP. Deletion of conceptual row would stop the redistribution of that protocol into RIP. SEQUENCE OF RipRedistributeEntry .1.3.6.1.4.1.738.1.6.4.1.1.2 |
ripRedistributeEntryThe conceptual row represents a routing protocol, redistributed into RIP RipRedistributeEntry .1.3.6.1.4.1.738.1.6.4.1.1.2.1 |
ripRedistributeProtocolThe specific routes redistributed into RIP. For T4R models the valid values are connected, static and OSPF. For T5 the valid values are kernel, connected, static and OSPF. For T5RN, T5Pro, T6, and E-series and G-series all of the above routes can be redistributedro Enumeration .1.3.6.1.4.1.738.1.6.4.1.1.2.1.1 |
ripRedistributeMetricThe metric, with which the external routes will be redistributed in the RIPrw INTEGER .1.3.6.1.4.1.738.1.6.4.1.1.2.1.2 |
ripRedistributeRouteMapThe route map that would filter the redistributed routing informationrw OCTET STRING .1.3.6.1.4.1.738.1.6.4.1.1.2.1.3 |
ripRedistributeRowStatusIndicates the status of the row. Setting of this field to active enables the redistribution of the protocol. Setting this field to destroy disables the redistribution of the protocolrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.738.1.6.4.1.1.2.1.4 |
More MIBs from BATM Advanced Communication
Browse all BATM Advanced CommunicationMIBs →SNMP MIB module
The PRVT-HQOS-MIB provides vendor-specific SNMP access to configure and monitor hierarchical Quality of Service (HQoS) parameters, including traffic class definitions, queue scheduling policies, and bandwidth allocation limits on network devices. This module enables granular control over packet prioritization, shaping, and policing mechanisms across multiple traffic levels to enforce service level agreements.
The PRVT-MPLS-TE-MIB module enables the monitoring and management of MPLS Traffic Engineering Label Switched Paths (LSPs) by exposing RSVP-TE and Constraint-Based LDP tunnel attributes, including bandwidth reservations, explicit route objects, and LSP state transitions. It facilitates the collection of operational metrics such as tunnel setup status, resource utilization, and constraint violations to support network capacity planning and fault isolation within MPLS core infrastructures.
SNMP MIB module
The PRVT-SWITCH-ACCESS-LIST-MIB module provides programmatic management of Layer 3 switch access control list (ACL) parameters, enabling the configuration and monitoring of packet filtering rules, rule ordering, and hit counters on private network switches.
PRVT-SWITCH-MIB provides the management interface for private switch hardware parameters, enabling the monitoring of port states, traffic counters, and configuration attributes via SNMP. This module facilitates the collection of operational metrics required for switch performance analysis and fault isolation in private network environments.