PRVT-OSPF-EXTENSION-MIB
Imported Objects
Objects
11 total| Object Name |
|---|
routingProtocols OBJECT IDENTIFIER .1.3.6.1.4.1.738.1.6.4 |
prvtOSPFExtensionMibThe OSPF extension MIB module contains additional information, needed to control the OSPF protocol, that is not found in the standard RFC MODULE-IDENTITY .1.3.6.1.4.1.738.1.6.4.2 |
ospfExtension OBJECT IDENTIFIER .1.3.6.1.4.1.738.1.6.4.2.1 |
ospfEnableThis object enables/disables the OSPF process in the switchrw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.738.1.6.4.2.1.1 |
ospfRedistributeTableThe table represents the routing protocols, redistributed into the OSPF routing domain. Creation of conceptual row in the table starts the redistribution of the specified protocol, which would lead to the injection of routing information from that protocol into the OSPF. Deletion of conceptual row would stop the redistribution of that protocol into the OSPF. OSPF router, which redistributes routing information from other protocols, is an ASBR router SEQUENCE OF OspfRedistributeEntry .1.3.6.1.4.1.738.1.6.4.2.1.2 |
ospfRedistributeEntryThe conceptual row represents a routing protocol, redistributed into OSPF OspfRedistributeEntry .1.3.6.1.4.1.738.1.6.4.2.1.2.1 |
ospfRedistributeProtocolThe specific routes redistributed into OSPF. For T4R model the valid values are connected, rip and static. For all the other models all of the above routes can be redistributedrw Enumeration .1.3.6.1.4.1.738.1.6.4.2.1.2.1.1 |
ospfRedistributeMetricThe metric, with which the external routes will be redistributed in the OSPFrw INTEGER .1.3.6.1.4.1.738.1.6.4.2.1.2.1.2 |
ospfRedistributeMetricTypeThe type of metric, with which the external routes are advertised into the OSPF routing domain. OSPF supports two types of external metrics. Type 1 external metrics are expressed in the same units as the OSPF interface cost (i.e., in terms of the link state metric). Type 2 external metrics are an order of magnitude larger; any Type 2 metric is considered greater than the cost of any path internal to the AS. Use of Type 2 external metrics assumes that routing between AS'es is the major cost of routing a packet, and eliminates the need for conversion of external costs to internal link state metrics.rw Enumeration .1.3.6.1.4.1.738.1.6.4.2.1.2.1.3 |
ospfRedistributeRouteMapThe route map that would filter the redistributed routing informationrw OCTET STRING .1.3.6.1.4.1.738.1.6.4.2.1.2.1.4 |
ospfRedistributeRowStatusIndicates the status of the row. Setting of this field to active enables the redistribution of the protocol. Setting this field to destroy disables the redistribution of the protocol.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.738.1.6.4.2.1.2.1.5 |
More MIBs from BATM Advanced Communication
Browse all BATM Advanced CommunicationMIBs →SNMP MIB module
The PRVT-HQOS-MIB provides vendor-specific SNMP access to configure and monitor hierarchical Quality of Service (HQoS) parameters, including traffic class definitions, queue scheduling policies, and bandwidth allocation limits on network devices. This module enables granular control over packet prioritization, shaping, and policing mechanisms across multiple traffic levels to enforce service level agreements.
The PRVT-MPLS-TE-MIB module enables the monitoring and management of MPLS Traffic Engineering Label Switched Paths (LSPs) by exposing RSVP-TE and Constraint-Based LDP tunnel attributes, including bandwidth reservations, explicit route objects, and LSP state transitions. It facilitates the collection of operational metrics such as tunnel setup status, resource utilization, and constraint violations to support network capacity planning and fault isolation within MPLS core infrastructures.
SNMP MIB module
The PRVT-SWITCH-ACCESS-LIST-MIB module provides programmatic management of Layer 3 switch access control list (ACL) parameters, enabling the configuration and monitoring of packet filtering rules, rule ordering, and hit counters on private network switches.
PRVT-SWITCH-MIB provides the management interface for private switch hardware parameters, enabling the monitoring of port states, traffic counters, and configuration attributes via SNMP. This module facilitates the collection of operational metrics required for switch performance analysis and fault isolation in private network environments.