PRVT-NETWORK-LOOPBACK-TEST-MIB
The PRVT-NETWORK-LOOPBACK-TEST-MIB manages embedded network loopback testing mechanisms on compatible hardware to enable or disable diagnostic traffic generation and measurement. It exposes control objects for initiating loopback sessions and monitoring the operational status of these troubleshooting features.
Imported Objects
Objects
14 total| Object Name |
|---|
prvtNetworkLoopbackTestMibThis MIB contains managed objects definitions for
encapsulating Loopback Tester feature that enables or disables
embedded mechanisms for network troubleshooting, diagnostics and measurement. MODULE-IDENTITY .1.3.6.1.4.1.738.1.6.7 |
SNMPv2-TCThis MIB contains managed objects definitions for
encapsulating Loopback Tester feature that enables or disables
embedded mechanisms for network troubleshooting, diagnostics and measurement. NOTIFICATION-TYPE .1.3.6.1.4.1.738.1.6.7 |
prvtNetworkLoopbackTestNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.738.1.6.7.0 |
prvtNetworkLoopbackTestFinishThis notification is sent when a Network Loopback Test is complete. NOTIFICATION-TYPE .1.3.6.1.4.1.738.1.6.7.0.1 |
prvtNetworkLoopbackTestObjects OBJECT IDENTIFIER .1.3.6.1.4.1.738.1.6.7.1 |
prvtNetworkLoopbackTestTableThis table contains object for configuring and display information about Network Loopback Tester. SEQUENCE OF PrvtNetworkLoopbackTestEntry .1.3.6.1.4.1.738.1.6.7.1.1 |
prvtNetworkLoopbackTestEntryAn entry in the prvtNetworkLoopbackTestTable table PrvtNetworkLoopbackTestEntry .1.3.6.1.4.1.738.1.6.7.1.1.1 |
prvtNetworkLoopTestDurationAn integer that identifies the duration in seconds of Loopback test.
For infinite Loopback tests object will have the value 0.rw INTEGER .1.3.6.1.4.1.738.1.6.7.1.1.1.1 |
prvtNetworkLoopStartDurationStar time of Loopback test.
For infinite Loopback tests object will have the value 0.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.738.1.6.7.1.1.1.2 |
prvtNetworkLoopEndDurationEnd time of Loopback test.
For infinite Loopback tests object will have the value 0.ro TimeStamp (SNMPv2-TC) .1.3.6.1.4.1.738.1.6.7.1.1.1.3 |
prvtNetworkLoopRowStatusNetwork Loopback Test RowStatus.
Both createAndGo(4) and createAndWait(5) are available.
CreateAndGo(4) is used for enable a Loopback test unlimited in time and CreateAndWait(4)
for enable a Loopback Test on a period specified by prvtNetworkLoopTestDuration.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.738.1.6.7.1.1.1.4 |
prvtNetworkLoopbackTestConformance OBJECT IDENTIFIER .1.3.6.1.4.1.738.1.6.7.2 |
prvtNetworkLoopTestCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.738.1.6.7.2.1 |
prvtNetworkLoopTestGroups OBJECT IDENTIFIER .1.3.6.1.4.1.738.1.6.7.2.2 |
More MIBs from BATM Advanced Communication
Browse all BATM Advanced CommunicationMIBs →SNMP MIB module
The PRVT-HQOS-MIB provides vendor-specific SNMP access to configure and monitor hierarchical Quality of Service (HQoS) parameters, including traffic class definitions, queue scheduling policies, and bandwidth allocation limits on network devices. This module enables granular control over packet prioritization, shaping, and policing mechanisms across multiple traffic levels to enforce service level agreements.
The PRVT-MPLS-TE-MIB module enables the monitoring and management of MPLS Traffic Engineering Label Switched Paths (LSPs) by exposing RSVP-TE and Constraint-Based LDP tunnel attributes, including bandwidth reservations, explicit route objects, and LSP state transitions. It facilitates the collection of operational metrics such as tunnel setup status, resource utilization, and constraint violations to support network capacity planning and fault isolation within MPLS core infrastructures.
SNMP MIB module
The PRVT-SWITCH-ACCESS-LIST-MIB module provides programmatic management of Layer 3 switch access control list (ACL) parameters, enabling the configuration and monitoring of packet filtering rules, rule ordering, and hit counters on private network switches.
PRVT-SWITCH-MIB provides the management interface for private switch hardware parameters, enabling the monitoring of port states, traffic counters, and configuration attributes via SNMP. This module facilitates the collection of operational metrics required for switch performance analysis and fault isolation in private network environments.