PRVT-CONFIGCHANGE-MIB
The PRVT-CONFIGCHANGE-MIB module generates SNMP traps to notify management systems of configuration modifications on the monitored network device. This mechanism enables automated detection and logging of policy, interface, or system setting alterations without requiring active polling of configuration files.
Imported Objects
Objects
12 total| Object Name |
|---|
prvtConfigChangeMIBInitial version. This MIB will provied traps for change MODULE-IDENTITY .1.3.6.1.4.1.738.1.5.150 |
prvtConfigChangeNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.738.1.5.150.0 |
prvtConfigChangeAlarmThis notification is generated when the value of configurable attribute has been changed. The notification can be used to trigger maintenance polling of the running configuration on the device. One of the varbinds will point either to entry of the modified table (configChangeAlarmRow) or the OID of the modified scalar object NOTIFICATION-TYPE .1.3.6.1.4.1.738.1.5.150.0.1 |
cliConfigurationChangeThis notification is generated when command in configuration node is executed. NOTIFICATION-TYPE .1.3.6.1.4.1.738.1.5.150.0.2 |
snmpServerStatusChangeThe notification shall be sent whenever the enabled/disabled status of the SNMP server changes. If the status is changed from enabled to disabled, the notification shall be sent prior to disabling the SNMP server. NOTIFICATION-TYPE .1.3.6.1.4.1.738.1.5.150.0.3 |
prvtConfigChangeObjects OBJECT IDENTIFIER .1.3.6.1.4.1.738.1.5.150.1 |
prvtConfigChangeAlarmOIDThe configChangeAlarmOID specifies the OID of an object whose value has been changed.ro OBJECT IDENTIFIER .1.3.6.1.4.1.738.1.5.150.1.1 |
prvtConfigChangeAlarmRowThe configChangeAlarmRow specifies the OID of the row from table, whose entry has been changed.ro RowPointer (SNMPv2-TC) .1.3.6.1.4.1.738.1.5.150.1.2 |
cliConfigChangeNodePromptShows the CLI prompt.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.738.1.5.150.1.3 |
cliConfigChangeCommandShows executed command.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.738.1.5.150.1.4 |
snmpServerStatusShows the enabled/disabled status of the SNMP server.ro Enumeration .1.3.6.1.4.1.738.1.5.150.1.5 |
prvtConfigChangeConformance OBJECT IDENTIFIER .1.3.6.1.4.1.738.1.5.150.3 |
More MIBs from BATM Advanced Communication
Browse all BATM Advanced CommunicationMIBs →SNMP MIB module
The PRVT-HQOS-MIB provides vendor-specific SNMP access to configure and monitor hierarchical Quality of Service (HQoS) parameters, including traffic class definitions, queue scheduling policies, and bandwidth allocation limits on network devices. This module enables granular control over packet prioritization, shaping, and policing mechanisms across multiple traffic levels to enforce service level agreements.
The PRVT-MPLS-TE-MIB module enables the monitoring and management of MPLS Traffic Engineering Label Switched Paths (LSPs) by exposing RSVP-TE and Constraint-Based LDP tunnel attributes, including bandwidth reservations, explicit route objects, and LSP state transitions. It facilitates the collection of operational metrics such as tunnel setup status, resource utilization, and constraint violations to support network capacity planning and fault isolation within MPLS core infrastructures.
SNMP MIB module
The PRVT-SWITCH-ACCESS-LIST-MIB module provides programmatic management of Layer 3 switch access control list (ACL) parameters, enabling the configuration and monitoring of packet filtering rules, rule ordering, and hit counters on private network switches.
PRVT-SWITCH-MIB provides the management interface for private switch hardware parameters, enabling the monitoring of port states, traffic counters, and configuration attributes via SNMP. This module facilitates the collection of operational metrics required for switch performance analysis and fault isolation in private network environments.