PRIV-LSL-MIB
Imported Objects
Objects
16 total| Object Name |
|---|
privLslMIB module for management of Logical Service Loopback(LSL) Iometrix compatible product. MODULE-IDENTITY .1.3.6.1.4.1.738.1.5.113 |
privLslLevel1 OBJECT IDENTIFIER .1.3.6.1.4.1.738.1.5.113.1 |
privLslObjects OBJECT IDENTIFIER .1.3.6.1.4.1.738.1.5.113.1.1 |
privLslGlobalMacAddressThis object defines the destination mac address assigned to lsl packets. The device can recognise the lsl packets by a specific destination mac address given by this object.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.738.1.5.113.1.1.1 |
privLslManagementTableLSL interface extention table. This table contains all objects which are used for LSL management per interface. It uses ifIndex defined in rfc1213 SEQUENCE OF PrivLslManagementEntry .1.3.6.1.4.1.738.1.5.113.1.1.2 |
privLslManagementEntryThe only valid LSL interfaces are phyical port interfaces PrivLslManagementEntry .1.3.6.1.4.1.738.1.5.113.1.1.2.1 |
privLslStatusThis object indicates whether the port have Logical Service Loopback enabled or disabled. It allows the client to determine which interface should be used for this type of servicerw PrivLslStates .1.3.6.1.4.1.738.1.5.113.1.1.2.1.1 |
privIometrixManagementTableIometrix Level 1 table. This table contains all objects which are used for Iometrix level 1 management per interface. It uses ifIndex defined in rfc1213 SEQUENCE OF PrivIometrixManagementEntry .1.3.6.1.4.1.738.1.5.113.1.1.3 |
privIometrixManagementEntrythe index is ifindex PrivIometrixManagementEntry .1.3.6.1.4.1.738.1.5.113.1.1.3.1 |
privIometrixStatusThis object indicates whether the port have Logical Service Loopback enabled or disabled. It allows the client to determine which interface should be used for this type of servicerw PrivLslStates .1.3.6.1.4.1.738.1.5.113.1.1.3.1.1 |
privLslNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.738.1.5.113.1.2 |
privLslConformance OBJECT IDENTIFIER .1.3.6.1.4.1.738.1.5.113.1.3 |
privLslGroups OBJECT IDENTIFIER .1.3.6.1.4.1.738.1.5.113.1.3.1 |
privLevel1ObjectsGroupAll objects related to level1 logical loopback service. Object grouping will be extended if the mib is also extended Unknown .1.3.6.1.4.1.738.1.5.113.1.3.1.1 |
privLslCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.738.1.5.113.1.3.2 |
privLevel1ComplianceThe compliance statement. It will be extended if new functionality is added Unknown .1.3.6.1.4.1.738.1.5.113.1.3.2.1 |
More MIBs from BATM Advanced Communication
Browse all BATM Advanced CommunicationMIBs →SNMP MIB module
The PRVT-HQOS-MIB provides vendor-specific SNMP access to configure and monitor hierarchical Quality of Service (HQoS) parameters, including traffic class definitions, queue scheduling policies, and bandwidth allocation limits on network devices. This module enables granular control over packet prioritization, shaping, and policing mechanisms across multiple traffic levels to enforce service level agreements.
The PRVT-MPLS-TE-MIB module enables the monitoring and management of MPLS Traffic Engineering Label Switched Paths (LSPs) by exposing RSVP-TE and Constraint-Based LDP tunnel attributes, including bandwidth reservations, explicit route objects, and LSP state transitions. It facilitates the collection of operational metrics such as tunnel setup status, resource utilization, and constraint violations to support network capacity planning and fault isolation within MPLS core infrastructures.
SNMP MIB module
The PRVT-SWITCH-ACCESS-LIST-MIB module provides programmatic management of Layer 3 switch access control list (ACL) parameters, enabling the configuration and monitoring of packet filtering rules, rule ordering, and hit counters on private network switches.
PRVT-SWITCH-MIB provides the management interface for private switch hardware parameters, enabling the monitoring of port states, traffic counters, and configuration attributes via SNMP. This module facilitates the collection of operational metrics required for switch performance analysis and fault isolation in private network environments.