OMNITRON-POE-MIB
AI MIB Summary
The OMNITRON-POE-MIB enables SNMP-based monitoring and management of Power over Ethernet (PoE) status, power allocation, and port states on Omnitron iConverter Management Modules v5.2 via the NetOutlook interface. It provides specific telemetry for PoE session counts, available power budgets, and fault detection to ensure reliable power delivery to connected network endpoints.
Omnitron PoE MIB for use with iConverter Management Modules v5.2 and NetOutlook. Copyright 2015 Omnitron Systems Technology, Inc. All rights reserved.
Main OID:
omnitronPoeMib.1.3.6.1.4.1.7342.15
25
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
25 total| Object Name |
|---|
omnitronPoeMibOmnitron PoE MIB for use with iConverter Management Modules v5.2 and NetOutlook. Copyright 2015 Omnitron Systems Technology, Inc. All rights reserved. MODULE-IDENTITY .1.3.6.1.4.1.7342.15 |
ostPoeGlobalCfgTable OBJECT IDENTIFIER .1.3.6.1.4.1.7342.15.1 |
ostPoeGlobalCfgPwrLimitationEnableThis object specifies whether the PoE PSE power limiting function is enabled. The value 'true' indicates that PoE PSE limiting is enabled. The value 'false' indicates that PoE PSE limiting is disabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.7342.15.1.1 |
ostPoeGlobalCfgTotalPwrThis object indicates the total power sourced in Watts.ro OstFloatValue (OMNITRON-TC-MIB) .1.3.6.1.4.1.7342.15.1.2 |
ostPoePortCfgTableThis table supports the port PoE configurations. SEQUENCE OF OstPoePortCfgEntry .1.3.6.1.4.1.7342.15.2 |
ostPoePortCfgEntryThis is a PoE port configuration table entry. OstPoePortCfgEntry .1.3.6.1.4.1.7342.15.2.1 |
ostPoePortCfgIndexAn index that is used to identify a specific PoE port number. OstPortSingleIndex (OMNITRON-TC-MIB) .1.3.6.1.4.1.7342.15.2.1.1 |
ostPoePortPseEnableThis object is the PoE PSE port enable. pseDisabled(1) PSE power source is disabled pseEnabled(2) PSE power source is enabledrw Enumeration .1.3.6.1.4.1.7342.15.2.1.2 |
ostPoePortPse60wModeThe object is the PoE PSE 60W mode enable. This is the same control as the physical DIP switch. pse60wNotAvail PSE 60W function not available pse60wAuto(1) PSE 60W auto mode enabled pse60wForce(2) PSE 60W force mode enabledrw Enumeration .1.3.6.1.4.1.7342.15.2.1.3 |
ostPoePortPdModeThis object is the PoE PD classification mode. pdModeNotDetected(1) PD is not detected pdModeNotClassified(2) PD is not classified pdModeFailure(3) PD classification failure pdModeClass0(4) PD is 802.3af Class 0 15W device pdModeClass1(5) PD is 802.3af Class 1 4W device pdModeClass2(6) PD is 802.3af Class 2 7W device pdModeClass3(7) PD is 802.3af Class 3 15W device pdModeClass4(8) PD is 802.3at Class 4 30W device pdMode60W(9) PD is 60W devicero Enumeration .1.3.6.1.4.1.7342.15.2.1.4 |
ostPoePortPseVoltageSuppliedThis object indicates the voltage output from the PSE port in volts.ro OstFloatValue (OMNITRON-TC-MIB) .1.3.6.1.4.1.7342.15.2.1.5 |
ostPoePortPseCurrentSuppliedThis object indicates the current output from the PSE port in mA (milliamps).ro OstFloatValue (OMNITRON-TC-MIB) .1.3.6.1.4.1.7342.15.2.1.6 |
ostPoePortPseStatusThis object is the PoE PSE port status. notApplicable(1) PD device not connected or port disabled pdNormal(2) PD device is being powered fully pdOverCurrent(3) PD device is consuming too much current pdBrownOut(4) PD device is not fully powered pdInsufficientPower(5) PD device not powered due to lack of power A write to this object restarts the PSE function and classification.rw Enumeration .1.3.6.1.4.1.7342.15.2.1.7 |
ostPoePortHeartbeatEnableThis object is the PoE PSE heartbeat enable. heartbeatDisabled(1) PSE PD heartbeat is disabled heartbeatEnabled(2) PSE PD heartbeat is enabledrw Enumeration .1.3.6.1.4.1.7342.15.2.1.8 |
ostPoePortHeartbeatIpAddressThis object is the PoE PD heartbeat IP address to ping.rw IpAddress .1.3.6.1.4.1.7342.15.2.1.9 |
ostPoePortHeartbeatIntervalThis object is the PoE PSE PD heartbeat transmission interval in seconds.rw Unsigned32 .1.3.6.1.4.1.7342.15.2.1.10 |
ostPoePortHeartbeatErrorDetectionThis object is the PoE PSE PD heartbeat number of consecutively lost heartbeat pings before an errored condition is declared. The number of consecutive error counts is cleared when a valid heartbeat response is received.rw Unsigned32 .1.3.6.1.4.1.7342.15.2.1.11 |
ostPoePortHeartbeatErrorActionThis object is the PoE PSE heartbeat errored condition action. errorLostIgnored(1) PD heartbeat errored condition is ignored errorRestart(2) PD heartbeat errored condition results in a restart errorShutdown(3) PD heartbeat errored condition results in a shutdown (power removed)rw Enumeration .1.3.6.1.4.1.7342.15.2.1.12 |
ostPoePortHeartbeatNumberRestartsThis object is the PoE PSE PD number of restarts when an errored hearbeat condition occurs. This object is only used when ostPoePortHeartbeatErrorAction is configured as 'errorRestart' A value of zero indicates restarts never stop.rw Unsigned32 .1.3.6.1.4.1.7342.15.2.1.13 |
ostPoEPortHeartbeatStatusThis object is the PoE PSE PD heartbeat status. heartbeatDisabled(1) PSE PD heartbeat is disabled heartbeatAvailable(2) PSE PD heartbeats are being received heartbeatErrored(3) PSE PD heartbeat is in an errored condition heartbeatRestart(4) PSE PD heartbeat error has caused a PSE restart heartbeatShutdown(5) PSE PD heartbeat error has caused a PSE shutdownro Enumeration .1.3.6.1.4.1.7342.15.2.1.14 |
ostPoEPortHeartbeatDeferTimeThis object is the PoE heartbeat PSE PD heartbeat transmission delay interval in seconds after the port has been reenabled. The delay is the amount of time after power has been applied before the heartbeat function starts and hence the detection of heartbeat errors.rw Unsigned32 .1.3.6.1.4.1.7342.15.2.1.15 |
ostPoeCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.7342.15.3 |
ostPoeComplianceThe compliance statement for the Omnitron PoE MIB. Unknown .1.3.6.1.4.1.7342.15.3.2 |
ostPoeGroups OBJECT IDENTIFIER .1.3.6.1.4.1.7342.15.4 |
ostPoeGroupMandatory objects for the PoE functional group. Unknown .1.3.6.1.4.1.7342.15.4.1 |