NEXTNET-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for NEXTNET-MIB.
412
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
412 total| Object Name |
|---|
nextnet OBJECT IDENTIFIER .1.3.6.1.4.1.4743 |
RFC1155-SMI Unknown .1.3.6.1.4.1.4743 |
nextnetTrapsSpecifies the nextnet traps.
This object is obsolete as of base station software version 4.3 and has no
replacement. TRAP-TYPE .1.3.6.1.4.1.4743.0.0 |
expedDev OBJECT IDENTIFIER .1.3.6.1.4.1.4743.1 |
expedDevMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4743.1.1 |
expedDevBase OBJECT IDENTIFIER .1.3.6.1.4.1.4743.1.1.1 |
expedDevRoleDefines the current role of this device. cpe (1) is
a Customer Premises Equipment, bssActive(2) is a Base Station
System which is controlling the system of CPE devices,
and bssBackup(3) is a Base Station system which is currently
connected, but not controlling the system (not currently used).
In general, if this device is a 'cpe', its role will not
change during operation or between reboots. If the
device is a 'bss' it may change between bssActive and
bssBackup and back again during normal operation.
At this time, the NextNet Expedience system does not support
the concept of a backup BSS, bssBackup is included for
completeness.ro Enumeration .1.3.6.1.4.1.4743.1.1.1.1 |
expedDevDateTimeThe date and time, with optional timezone information.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.4743.1.1.1.2 |
expedDevSerialNumberThe manufacturer's serial number for this device.ro DisplayString .1.3.6.1.4.1.4743.1.1.1.3 |
expedDevSTPControlThis object controls operation of the spanning tree
protocol (as distinguished from transparent bridging).
If set to stEnabled(1) then the spanning tree protocol
is enabled, subject to bridging constraints. If
noStFilterBpdu(2), then spanning tree is not active,
and Bridge PDUs received are discarded.
If noStPassBpdu(3) then spanning tree is not active
and Bridge PDUs are transparently forwarded. Note that
a device need not implement all of these options,
but that noStFilterBpdu(2) is required.ro Enumeration .1.3.6.1.4.1.4743.1.1.1.4 |
expedDevGpsStatusThe status string coming from the GPSro DisplayString .1.3.6.1.4.1.4743.1.1.1.5 |
expedDevGpsMonitorStateThe state of the GPS Clock Monitor. The following states are possible.
gCState-NoGps (No GPS for this base station), gCState-Init (Waiting for
init to complete), gCState-Correcting (initial time solved, needs
correction) gCState-Undetermined (floating init time solution),
gCState-Unreliable (init time drifted too far), gCState-Locked (full
time solution), gCState-Floating (Floating full time solution), and
gCState-Drifted (full time solution drifted too far.ro Enumeration .1.3.6.1.4.1.4743.1.1.1.6 |
expedDevGpsClockOKIndicates whether the GPS timing pulse is considered valid. If a
base is operating without a GPS unit, then this element will be True.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.1.1.7 |
expedDevPpsStatusIndicates whether the one-second timing pulse is being delivered to
the base station. If a base is operating with a GPS unit, then the
timing pulse refers to the pulse being delivered by the GPS unit.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.1.1.8 |
expedDevAirlinkStatusThe status of the Airlink.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.1.1.9 |
expedDevWriteFlashSetting this flag to enable will cause the configuration to be
written to flashrw Enumeration .1.3.6.1.4.1.4743.1.1.1.10 |
expedDevRebootDeviceSetting this flag to enable will cause the device to be rebootedrw Enumeration .1.3.6.1.4.1.4743.1.1.1.11 |
expedDevZeroStatsZeros out the appropriate statsrw Enumeration .1.3.6.1.4.1.4743.1.1.1.12 |
expedDevTemperatureCurrent temperature of the devicero INTEGER .1.3.6.1.4.1.4743.1.1.1.13 |
expedDevModelIdModel Identifier for the base station. The primary hardware
features of the base station are specified by this string
representation of a hexidecimal, 32-bit number with a range
of 00000000 - FFFFFFFF and a format of ABCCDDEE.
A => Model Category
0 => Outdoor Base Station
1 => Indoor CPE
2 => Outdoor CPE
3 => Indoor Base Station
4 => Mobile Subscriber Unit
B => Reserved
0 => Default
CC => Board Type
01 => FPGA Wedge
02 => Dual Board ASIC Wedge, Davicom
03 => Single Board ASIC Wedge, SMSC, Indoor
04 => Single Board ASIC, SMSC, Outdoor
05 => Slimline, ASIC
12 => AMOD Dual Board, ASIC
15 => AMOD Slimline, ASIC
16 => AMOD 5407 Coldfire, ASIC
17 => AMOD LX CPE
18 => AMOD LX SoC CPE
22 => AMOD 5484 Coldfire, ASIC Base
DD => Reserved
00 => 2.6 GHz
01 => 3.3 GHz
02 => 3.5 GHz
03 => 2.4 GHz
04 => 2.3 GHz
05 => 700MHz
06 => 3.7 GHz
EE => Special Options
00 => External Antenna
01 => Vertical Antenna
02 => Horizontal Antennaro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.1.1.14 |
expedDevSoftware OBJECT IDENTIFIER .1.3.6.1.4.1.4743.1.1.2 |
expedDevSwCurrentVersThe software version currently operating in this device.ro DisplayString .1.3.6.1.4.1.4743.1.1.2.1 |
expedDevServer OBJECT IDENTIFIER .1.3.6.1.4.1.4743.1.1.3 |
expedDevBootStateIf operational(1), the device has completed loading and
processing of configuration parameters and the Base Station is
operational. If airlinkdisabled(2) then the device was
administratively disabled. If privatemode(3), the device is
operational and is in privatemode.ro Enumeration .1.3.6.1.4.1.4743.1.1.3.1 |
expedDevDhcpThe IP address of the DHCP server that assigned an IP
address to this device. Returns 0.0.0.0 if DHCP was not
used for IP address assignment.ro IpAddress .1.3.6.1.4.1.4743.1.1.3.2 |
expedDevFTPPortThe port number that FTP is listening on.rw INTEGER .1.3.6.1.4.1.4743.1.1.3.3 |
expedDevFTPRemoteThe IP address mask that is allowed access to FTP.
255.255.255.255 allows access to everyone.rw IpAddress .1.3.6.1.4.1.4743.1.1.3.4 |
expedDevFTPTimeoutThe max timeout in seconds to allow an FTP session to remain
idle.rw INTEGER .1.3.6.1.4.1.4743.1.1.3.5 |
expedDevFTPStateEnables/Disables FTP.rw Enumeration .1.3.6.1.4.1.4743.1.1.3.6 |
expedDevHostTraceAddressThe MAC address of the host to trace for debugging host
traffic.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.1.3.7 |
expedDevHostTraceFilterThis parameter allows a user to filter out host trace
messages (i.e. discard them) for broadcast, or uplink or downlink
frames.rw Enumeration .1.3.6.1.4.1.4743.1.1.3.8 |
expedDevHostTraceStateEnable/Disable individual host syslog tracing.rw Enumeration .1.3.6.1.4.1.4743.1.1.3.9 |
expedDevTelnetPortThe port number that Telnet is listening on.rw INTEGER .1.3.6.1.4.1.4743.1.1.3.10 |
expedDevTelnetRemoteThe IP address mask that is allowed access to Telnet.
255.255.255.255 allows access to everyone.rw IpAddress .1.3.6.1.4.1.4743.1.1.3.11 |
expedDevTelnetTimeoutThe max timeout in seconds to allow a Telnet session to remain
idle.rw INTEGER .1.3.6.1.4.1.4743.1.1.3.12 |
expedDevTelnetStateEnables/Disables Telnet.rw Enumeration .1.3.6.1.4.1.4743.1.1.3.13 |
expedDevWebPortThe port number that WEB is listening on.
This object is obsolete as of base station software version
4.3 and has no replacement.rwobsolete INTEGER .1.3.6.1.4.1.4743.1.1.3.14 |
expedDevWebRemoteThe IP address mask that is allowed access to Web.
255.255.255.255 allows access to everyone.
This object is obsolete as of base station software version
4.3 and has no replacement.rwobsolete IpAddress .1.3.6.1.4.1.4743.1.1.3.15 |
expedDevWebStateEnables/Disables WEB.
This object is obsolete as of base station software version
4.3 and has no replacement.rwobsolete Enumeration .1.3.6.1.4.1.4743.1.1.3.16 |
expedDevVTTimeoutThe max timeout in seconds to allow a Virtual Telnet session
to wait for a reponse. This object is obsolete as of base
station software version 4.3 and has no replacement.rwobsolete INTEGER .1.3.6.1.4.1.4743.1.1.3.17 |
expedDevSysSectorThe system sector.rw DisplayString .1.3.6.1.4.1.4743.1.1.3.18 |
expedDevSysCellThe system cell.rw DisplayString .1.3.6.1.4.1.4743.1.1.3.19 |
expedDevVlanPortIDThe Ethernet Port VLAN ID. The PVID
is the VLAN ID that is applied to any received frames on the
Ethernet port that are not tagged with a VLAN ID. This
parameter only takes effect following a reboot of the base
station. Setting to 0 disables this feature.rw INTEGER .1.3.6.1.4.1.4743.1.1.3.20 |
expedDevVlanLegacyIDThe VLAN legacy ID. Selects the VLAN ID for all legacy CPEs
that register with the base station. This parameter only
takes effect following a reboot of the base station. A
legacy CPE is defined as a CPE running 1.X code. Note that
this VLAN ID is applied to all CPE's when AAA Authority is
local.
This object is obsolete as of base station software version 4.3
and is replaced by expedIfBssAAALocalVlan.rwobsolete INTEGER .1.3.6.1.4.1.4743.1.1.3.21 |
expedDevVlanMgmtIDThe VLAN Management ID. Selects the VLAN ID of the management VLAN,
which is the VLAN used by the local IP stack of the base stations.
This parameter only takes effect following a reboot of the base
station.rw INTEGER .1.3.6.1.4.1.4743.1.1.3.22 |
expedDevVlanUntaggedIDThe VLAN Untagged ID. Configures the selected VLAN to transmit
untagged frames (no 802.1Q tag). This parameter only takes effect
following a reboot of the base station. Any Ethernet frames
transmitted from the base station on this VLAN will be untagged.
Setting to 0 disables this feature.rw INTEGER .1.3.6.1.4.1.4743.1.1.3.23 |
expedDevSysLocationThe system location.rw DisplayString .1.3.6.1.4.1.4743.1.1.3.24 |
expedDevSysNameThe system name.rw DisplayString .1.3.6.1.4.1.4743.1.1.3.25 |
expedDevCpuUtilizationThe current base station CPU utilization, expressed as a
percentage.ro INTEGER .1.3.6.1.4.1.4743.1.1.3.26 |
expedDevEvent OBJECT IDENTIFIER .1.3.6.1.4.1.4743.1.1.4 |
expedDevEvSyslogThe IP address of the Syslog server. If 0.0.0.0, syslog
transmission is inhibited.rw IpAddress .1.3.6.1.4.1.4743.1.1.4.1 |
expedDevEvSyslogStateEnables/Disables Syslog.rw Enumeration .1.3.6.1.4.1.4743.1.1.4.2 |
expedDevEvControlTableThis table allows control of the reporting of event classes.
For each event facility, the minimum level to send a syslog message and
the minimum level to send a trap can be configured. SEQUENCE OF ExpedDevEvControlEntry .1.3.6.1.4.1.4743.1.1.4.3 |
expedDevEvControlEntryAllows configuration of the reporting mechanisms for a
particular event priority. ExpedDevEvControlEntry .1.3.6.1.4.1.4743.1.1.4.3.1 |
expedDevEvFacilityThe Facility Level to control for sending traps and syslog messages.
log-fac-cfginit is used to control traps and syslog messagesfor configuration and initialization,
log-fac-airlink-mac is used to control traps and syslog messagesfor the airlink mac,
log-fac-nnmgr is used to control traps and syslog messages for the the airlink manager,
log-fac-relay is used to control traps and syslog messages for the the relay,
log-fac-stack is used to control traps and syslog messages for the the ip stack,
log-fac-aaa is used to control traps and syslog messages for the aaa server,
log-fac-ether-mac is used to control traps and syslog messages for the ethernet driverro Enumeration .1.3.6.1.4.1.4743.1.1.4.3.1.1 |
expedDevEvSyslogMinDefines the minimum level for sending a syslog message, all syslog messages
at and above this level will be sent to the syslog serverrw Enumeration .1.3.6.1.4.1.4743.1.1.4.3.1.2 |
expedDevEvTrapMinDefines the minimum level for sending a syslog message, all syslog messages
at and above this level will be sent to the SNMP manger as a traprw Enumeration .1.3.6.1.4.1.4743.1.1.4.3.1.3 |
expedDevFilter OBJECT IDENTIFIER .1.3.6.1.4.1.4743.1.1.5 |
expedIfMibObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4743.1.2 |
expedIfBaseObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4743.1.2.1 |
expedIfAddressThe Device airlink MAC addressro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.1.1 |
expedIfChannelIdThe Base Station System identification
of the channel within this particular MAC
interface. If the interface is down, the object returns
the most current value. If the channel ID is
unknown, this object returns a value of 0.
This object is obsolete as of base station software version
4.3 and is replaced by expedIfRadioFrequency.rwobsolete INTEGER .1.3.6.1.4.1.4743.1.2.1.2 |
expedIfChannelFrequencyThe center of the frequency associated with the channel
in use, which is stored in expedIfChannelId. The unit
of this object is KHz.
This object is obsolete as of base station software version
4.3 and is replaced by expedIfRadioFrequency.roobsolete INTEGER .1.3.6.1.4.1.4743.1.2.1.3 |
expedIfChannelWidthThe width of the channel in use, which is stored in
expedIfChannelId. Most implementations are expected to
support a channel width of 6 MHz (North America) and/or
8 MHz (Europe). The unit of this object is KHz.
This object is obsolete as of base station software version
4.3 and is replaced by expedIfRadioFrequency.roobsolete INTEGER .1.3.6.1.4.1.4743.1.2.1.4 |
expedIfTXAGCThis specifies the automatic gain control (AGC) applied to
the transmitter, for setting the maximum power output of the
transmitter. This object is obsolete as of base station
software version 4.3 and has no replacement.roobsolete INTEGER .1.3.6.1.4.1.4743.1.2.1.5 |
expedIfAirlinkStateThis enables and disables the airlinkrw Enumeration .1.3.6.1.4.1.4743.1.2.1.6 |
expedIfRXAGCThis specifies the the automatic gain control applied to the
receiver. This object is obsolete as of base station software
version 4.3 and has no replacement.roobsolete INTEGER .1.3.6.1.4.1.4743.1.2.1.7 |
expedIfAirlinkTimingThis selects the source for the one pulse-per-second.
The source will either be external, meaning a GPS source,
internal, or external pulse-per-second generated without a GPS
unit. The time synchronization signal is needed to ascertain
the proper timing for TDD (Time Division Duplexing).rw Enumeration .1.3.6.1.4.1.4743.1.2.1.9 |
expedIfAirlinkColorCodeThis sets the home color code for this base station.
The color code is broadcasted to all CPE's.rw INTEGER .1.3.6.1.4.1.4743.1.2.1.10 |
expedIfAirlinkExtRangeThis sets the maximum cell size that is broadcasted to all CPE's.
Each step indicates a 5 mile radius cell size. CPE's outside the
advertised cell size will not try to register with this base.rw INTEGER .1.3.6.1.4.1.4743.1.2.1.11 |
expedIfBaseRegNotPrefControls registration for this base. If set to True then this Base
is advertising to other CPE's that it is busy and should try other bases
first.
This object is obsolete as of base station software version 4.3
and has no replacement.rwobsolete Enumeration .1.3.6.1.4.1.4743.1.2.1.12 |
expedIfBssDownChannelPowerThe Base Station System operational transmit power.
The range is 6 to 31 for 2 watts base, 10 to 31 for 2 watts base
and 16 to 31 for 0.5 watts base. If the interface is down, this
object either returns the configured value, the most current
value or the value of 0.rw TenthdBmV -- UNITS "dBmV" .1.3.6.1.4.1.4743.1.2.1.13 |
expedIfBssDownlinkBiasThe Base Station System Downlink Bias. This Bias sets up the
number of uplink and downlink slots.rw INTEGER .1.3.6.1.4.1.4743.1.2.1.14 |
expedIfBssDownSlotsDirects the Base Station to transmit this number of down link
symbols in each frame. Note that this number must be related to
the number of up link symbols as follows:
(Down Link Symbols) = (Up Link Symbols) + (Down Link Up Link Bias) * 4.ro INTEGER .1.3.6.1.4.1.4743.1.2.1.15 |
expedIfBssUpSlotsDirects the Base Station to expect this number of up link symbols
in each frame. This is the number of down link symbols that will
contain an UCS field. A CPE determines the existence of an up link
symbol slot by detecting this UCS. This is a system wide configuration
number and is used by the CPEs to facilitate frame synchronization.
This number is to be a multiple of three (0,3,6,x). If this number
is 0 then the system will be set up for continuous down link operation,
allowing no up link operation.ro INTEGER .1.3.6.1.4.1.4743.1.2.1.16 |
expedIfAirlinkPowerControlEnables and disables the airlink power control task. This task when enabled
will shut the airlink down when power goes below a pre-determined power level
or goes above a pre-determined power level.ro Enumeration .1.3.6.1.4.1.4743.1.2.1.17 |
expedIfUplinkSlotUsageTableAt the CPE, describes the PHY signal quality of downstream
channels. At the BSS, describes the PHY signal quality of
upstream channels. SEQUENCE OF ExpedIfUplinkSlotUsageEntry .1.3.6.1.4.1.4743.1.2.1.18 |
expedIfUplinkSlotUsageEntryStatus information for an uplink slot. ExpedIfUplinkSlotUsageEntry .1.3.6.1.4.1.4743.1.2.1.18.1 |
expedIfUplinkSlotUsageIndexIndex value to uniquely identify an entry in this table, on a per-slot basis.ro INTEGER .1.3.6.1.4.1.4743.1.2.1.18.1.1 |
expedIfUplinkSlotUsageUseCountNumber of good symbols in slot.ro Counter .1.3.6.1.4.1.4743.1.2.1.18.1.2 |
expedIfUplinkSlotUsageFreeCountNumber of free slots.ro Counter .1.3.6.1.4.1.4743.1.2.1.18.1.3 |
expedIfUplinkSlotUsageRetryCountNumber of symbols that had to be retried.ro Counter .1.3.6.1.4.1.4743.1.2.1.18.1.4 |
expedIfUplinkSlotUsageBytesRecvdNumber of bytes in the received messages.ro Counter .1.3.6.1.4.1.4743.1.2.1.18.1.5 |
expedIfUplinkSlotUsageMsgsRecvdNumber of received messages.ro Counter .1.3.6.1.4.1.4743.1.2.1.18.1.6 |
expedIfUplinkSlotTotUseCountNumber of good symbols in all 6 slots combined.ro Counter .1.3.6.1.4.1.4743.1.2.1.19 |
expedIfUplinkSlotTotFreeCountNumber of free slots in all 6 slots combined.ro Counter .1.3.6.1.4.1.4743.1.2.1.20 |
expedIfUplinkSlotTotRetryCountNumber of symbols that had to be retried in all 6 slots combined.ro Counter .1.3.6.1.4.1.4743.1.2.1.21 |
expedIfUplinkSlotTotBytesRecvdNumber of bytes in the received messages in all 6 slots combined.ro Counter .1.3.6.1.4.1.4743.1.2.1.22 |
expedIfUplinkSlotTotMsgsRecvdNumber of received messages in all 6 slots combined.ro Counter .1.3.6.1.4.1.4743.1.2.1.23 |
expedIfDownlinkBytesNumber of bytes on the downlink.ro Counter .1.3.6.1.4.1.4743.1.2.1.24 |
expedIfDownlinkSymbolsUsedNumber of symbols used on the downlink.ro Counter .1.3.6.1.4.1.4743.1.2.1.25 |
expedIfDownlinkSymbolsFreeNumber of symbols free on the downlink.ro Counter .1.3.6.1.4.1.4743.1.2.1.26 |
expedIfDownlinkMsgsUnicastNumber of messages on the downlink that are unicast.ro Counter .1.3.6.1.4.1.4743.1.2.1.27 |
expedIfDownlinkMsgsNUnicastNumber of messages on the downlink that are broadcast.ro Counter .1.3.6.1.4.1.4743.1.2.1.28 |
expedIfDownlinkSaturationPercent of slot usage on the downlink.ro INTEGER .1.3.6.1.4.1.4743.1.2.1.29 |
expedIfUplinkSaturationPercent of saturation on the uplink.ro INTEGER .1.3.6.1.4.1.4743.1.2.1.30 |
expedIfMaxModLevelMaximum modulation level for base. The acceptable values are
0 (QPSK), 1 (16 QAM), 2 (64 QAM) and 5 (16 QAM Lite).rw INTEGER .1.3.6.1.4.1.4743.1.2.1.31 |
expedIfMaxModLevelStringMaximum modulation level for base in string format.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.1.32 |
expedIfSoftRssiThis setting represents a transmit limit on the registered CPEs.
A CPE will reduce its transmit power if its downlink RSSI is greater
than this value. Transmit power will be reduced by the difference
between the downlink RSSI and this value.rw INTEGER .1.3.6.1.4.1.4743.1.2.1.33 |
expedIfRadioFrequencyThis object represents the configured frequency and bandwidth
for the Airlink tranceiver in the target base station device.
The format of this string is <frequency>-<bandwidth>[:<alias>].
The frequency specifies the center frequency in KHz. This
value must be a multiple of 250, have exactly 7 decimal
digits, and fall between the low and high frequency
calibration points for the target base station device.
The bandwidth specifies the width of the frequency in HKz.
This value must be one of the following: 2500, 2750, 3000,
3500, 4000, 5000, 5500, 6000, 7000, or 8000.
Most implementations are expected to support a channel width
of 6000 KHz (North America) and/or 8000 KHz (Europe).
This object replaces the expedIfChannelId,
expedIfChannelFrequency, and expedIfChannelWidth objects.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.1.34 |
expedIfBssDownChannelPowerLimitThe minimum limit of the Base Station System operational transmit
power. The value is 16 for 0.5 watts base, 10 for 2 watts base,
and 6 for 5 watts base.ro TenthdBmV -- UNITS "dBmV" .1.3.6.1.4.1.4743.1.2.1.35 |
expedIfMaxModLevelLimitThe limit of the maximum modulation level for base. The acceptable
values are 0 (QPSK), 1 (16 QAM), 2 (64 QAM) and 5 (16 QAM Lite).ro INTEGER .1.3.6.1.4.1.4743.1.2.1.36 |
expedIfMaxNumOfCPEsMaximum cpes supported by the base DB.rw INTEGER .1.3.6.1.4.1.4743.1.2.1.37 |
expedIfMaxNumOfCPEsLimitThe limit of the maximum cpes supported by the base DB.ro INTEGER .1.3.6.1.4.1.4743.1.2.1.38 |
expedIfMaxNumOfHostsMaximum hosts supported by the base DB.rw INTEGER .1.3.6.1.4.1.4743.1.2.1.39 |
expedIfBssObjects OBJECT IDENTIFIER .1.3.6.1.4.1.4743.1.2.2 |
expedIfBssCapabilitiesIdentifies the capabilities of the BSS MAC
implementation at this interface. Note that packet
transmission is always supported. Therefore, there
is no specific bit required to explicitely indicate
this capability.ro Enumeration .1.3.6.1.4.1.4743.1.2.2.1 |
expedIfBssNumOfCPEsNumber of CPE's currently registered on the Base stationro INTEGER .1.3.6.1.4.1.4743.1.2.2.2 |
expedIfBssNumOfHostsNumber of Hosts currently registered on the Base stationro INTEGER .1.3.6.1.4.1.4743.1.2.2.3 |
expedIfBssNumOfCPEsHighMarkHighest Number of CPE's that were registered on the Base stationro Counter .1.3.6.1.4.1.4743.1.2.2.4 |
expedIfBssNumOfHostsHighMarkHighest Number of Hosts that were registered on the Base stationro Counter .1.3.6.1.4.1.4743.1.2.2.5 |
expedIfBssRelayCpeIdleTimeThe amount of time in seconds that the CPE can be idle before it is deleted
from the base station. Idle time is defined as no uplink traffic from
the CPE.rw INTEGER .1.3.6.1.4.1.4743.1.2.2.6 |
expedIfBssRelayDHCPTimeoutThe amount of time in seconds waiting for completion of the DHCP
conversation.rw INTEGER .1.3.6.1.4.1.4743.1.2.2.7 |
expedIfBssRelayMaxTransitThe max amount of time in 10ths of a second a datagram frame can
live within the device before it is considered stale and is
deleted.rw INTEGER .1.3.6.1.4.1.4743.1.2.2.8 |
expedIfBssAAAStateEnables/Disables AAA Server.rw Enumeration .1.3.6.1.4.1.4743.1.2.2.9 |
expedIfBssAAAConnectionTimeDate and Time of the current AAA connection.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.10 |
expedIfBssAAAConnectionAttemptsNumber of attempts for the current AAA connection.ro Counter .1.3.6.1.4.1.4743.1.2.2.11 |
expedIfBssAAAConfigConnectionThe configuration parameter that controls the address of the AAA
server(s). This can be one or two IP addresses, separated by
a space or comma, to specify a primary and a backup AAA server.
expedIfBssAAACurrentConnection shows the IP address currently
being used.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.12 |
expedIfBssAAACurrentConnectionIP address of the current AAA connection.ro IpAddress .1.3.6.1.4.1.4743.1.2.2.13 |
expedIfBssAAAAuthorityThe Authority can be either local or remote. Local uses
local authority parameters defined in ExpedIfBssLocalConfig
for CPE permissions. Remote looks for authority from a
Remote AAA Server for CPE permissions.rw Enumeration .1.3.6.1.4.1.4743.1.2.2.14 |
expedIfBssAAACachingEnables/Disables aaa caching during remote authority.
When enabled if the cpe is known by the base then the base
will act as a cache and give authorization based on the
last registration.
This object is obsolete as of base station software version 4.3
and has no replacement.rwobsolete Enumeration .1.3.6.1.4.1.4743.1.2.2.15 |
expedIfBssAAAPortThe Port the AAA Server is listening on.rw INTEGER .1.3.6.1.4.1.4743.1.2.2.16 |
expedIfBssAAARegRequestsNumber of CPE registration requests received over the air.ro Counter .1.3.6.1.4.1.4743.1.2.2.17 |
expedIfBssAAARegDenysNumber of permission vectors that indicate a deny for a CPE
registration.ro Counter .1.3.6.1.4.1.4743.1.2.2.18 |
expedIfBssAAARegConfirmsNumber of permission vectors that indicate a confirm for a CPE
registration.ro Counter .1.3.6.1.4.1.4743.1.2.2.19 |
expedIfBssAAARegCacheNumber of registration confirms due to caching.
This object is obsolete as of base station software version 4.3
and has no replacement.roobsolete Counter .1.3.6.1.4.1.4743.1.2.2.20 |
expedIfBssAAARegDuplicatesNumber of registration requests that are duplicates of a current
registration request. Indicates that a second registration was
received for a given CPE before the permission vector was received from
the AAA server.ro Counter .1.3.6.1.4.1.4743.1.2.2.21 |
expedIfBssAAANoAAAResponseNumber of registration requests that never received a permission vector
from the AAA server.ro Counter .1.3.6.1.4.1.4743.1.2.2.22 |
expedIfBssAAACDRsSentNumber of CDR's sent to the AAA server.ro Counter .1.3.6.1.4.1.4743.1.2.2.23 |
expedIfBssAAAPVsRecvNumber of PV's received from the AAA server.ro Counter .1.3.6.1.4.1.4743.1.2.2.24 |
expedIfBssAAAUnexpectedPVNumber of PV's received from the AAA server, that were not expected.ro Counter .1.3.6.1.4.1.4743.1.2.2.25 |
expedIfBssCpeStatusTableA set of objects in the BSS, maintained for each
CPE connected to this base station. SEQUENCE OF ExpedIfBssCpeStatusEntry .1.3.6.1.4.1.4743.1.2.2.26 |
expedIfBssCpeStatusEntryStatus information for a single CPE.
An entry in this table exists for each CPE
that is connected to the BSS implementing this table. ExpedIfBssCpeStatusEntry .1.3.6.1.4.1.4743.1.2.2.26.1 |
expedIfBssCpeStatusIndexIndex value to uniquely identify an entry in this table.
For an individual CPE, this index value should
not change during BSS uptime.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.26.1.1 |
expedIfBssCpeStatusMacAddressMAC address of this CPE. If the CPE has
multiple MAC addresses, this is the MAC address associated
with the Airlink interface.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.26.1.2 |
expedIfBssCpeStatusBytesFromNumber of bytes in from this CPE.ro Counter .1.3.6.1.4.1.4743.1.2.2.26.1.3 |
expedIfBssCpeStatusBytesToNumber of bytes out to this CPE.ro Counter .1.3.6.1.4.1.4743.1.2.2.26.1.4 |
expedIfBssCpeStatusMsgsFromNumber of Msgs in from this CPE.ro Counter .1.3.6.1.4.1.4743.1.2.2.26.1.5 |
expedIfBssCpeStatusMsgsToNumber of Msgs out to this CPE.ro Counter .1.3.6.1.4.1.4743.1.2.2.26.1.6 |
expedIfBssCpeNumOfHostsNumber of hosts allowed for this CPE.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.26.1.7 |
expedIfBssCpeISPIdThis contains the ID of the ISP that owns this CPE .ro INTEGER .1.3.6.1.4.1.4743.1.2.2.26.1.8 |
expedIfBssCpeVIDThis contains the VLAN ID the CPE has been assigned to.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.26.1.9 |
expedIfBssCpeStatusLastTimeThe date and time last heard from this CPE.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.26.1.10 |
expedIfBssDynamicIPAssignmentA true indicates that hosts behind this CPE acquire their IP
Address via DHCP. False indicates static IP assignment.
This object is obsolete.roobsolete TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.26.1.11 |
expedIfBssCpeSwVersionVersion of software this CPE is running.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.26.1.12 |
expedIfBssCpeNumOfCallsNumber Of Current Calls on this CPEro INTEGER .1.3.6.1.4.1.4743.1.2.2.26.1.13 |
expedIfBssCpeDataPollsNumber Of Data Polls from this CPEro Counter .1.3.6.1.4.1.4743.1.2.2.26.1.14 |
expedIfBssCpeDryPollsNumber Of Dry Polls from this CPEro Counter .1.3.6.1.4.1.4743.1.2.2.26.1.15 |
expedIfBssCpeNoResponseNumber Of No Response to Polls from this CPEro Counter .1.3.6.1.4.1.4743.1.2.2.26.1.16 |
expedIfBssCpeCallEfficiencyEfficiency use of the Bandwidth for this CPEro INTEGER .1.3.6.1.4.1.4743.1.2.2.26.1.17 |
expedIfBssCpeBWUsageSync Session Bandwidth Usage for all calls on this CPE from the
perspective of basero INTEGER .1.3.6.1.4.1.4743.1.2.2.26.1.18 |
expedIfBssCpeDownModulationDownlink Modulation Levelro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.26.1.19 |
expedIfBssCpeDownLinkBandWidthProvisioned Downlink BandWidth limit. Unit is kbps. 'none' means no
limit.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.26.1.20 |
expedIfBssCpeUplinkBandWidthProvisioned Uplink BandWidth limit. Unit is kbps. 'none' means no
limit.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.26.1.21 |
expedIfBssCpeIdleTimeAmount of time the CPE has been idlero Counter .1.3.6.1.4.1.4743.1.2.2.26.1.22 |
expedIfBssCpeModelIdModel Identifier for the subscriber unit. The primary hardware
features of the subscriber unit are specified by this string
representation of a hexidecimal, 32-bit number with a range
of 00000000 - FFFFFFFF and a format of ABCCDDEE.
A => Model Category
0 => Outdoor Base Station
1 => Indoor CPE
2 => Outdoor CPE
3 => Indoor Base Station
4 => Mobile Subscriber Unit
B => Reserved
0 => Default
CC => Board Type
01 => FPGA Wedge
02 => Dual Board ASIC Wedge, Davicom
03 => Single Board ASIC Wedge, SMSC, Indoor
04 => Single Board ASIC, SMSC, Outdoor
05 => Slimline, ASIC
12 => AMOD Dual Board, ASIC
15 => AMOD Slimline, ASIC
16 => AMOD 5407 Coldfire, ASIC
17 => AMOD LX CPE
18 => AMOD LX SoC CPE
22 => AMOD 5484 Coldfire, ASIC Base
DD => Reserved
00 => 2.6 GHz
01 => 3.3 GHz
02 => 3.5 GHz
03 => 2.4 GHz
04 => 2.3 GHz
05 => 700MHz
06 => 3.7 GHz
EE => Special Options
00 => External Antenna
01 => Vertical Antenna
02 => Horizontal Antennaro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.26.1.23 |
expedIfBssNumStaticHostsNumber of static hosts allowed for this CPE.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.26.1.24 |
expedIfBssCpeHostTableA set of objects in the BSS, maintained for each
Host/CPE connected to this base station. SEQUENCE OF ExpedIfBssCpeHostEntry .1.3.6.1.4.1.4743.1.2.2.27 |
expedIfBssCpeHostEntryHost information for a single CPE.
An entry in this table exists for each CPE/Host
that is connected to the BSS implementing this table. ExpedIfBssCpeHostEntry .1.3.6.1.4.1.4743.1.2.2.27.1 |
expedIfBssCpeHostIndexIndex value to uniquely identify an entry in this table.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.27.1.1 |
expedIfBssCpeHostMacAddressMAC address of this CPE/Host.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.27.1.2 |
expedIfBssCpeAirlinkMacAddressAirlink MAC address of this CPE.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.27.1.3 |
expedIfBssCpeHostIpAddressIP address of this Host.ro IpAddress .1.3.6.1.4.1.4743.1.2.2.27.1.4 |
expedIfBssCpeHostIpTypeIndicates the type of host. Either dynamic, static or bound
CPE Host.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.27.1.5 |
expedIfBssCpeHostPPPOEIndicates status of any PPOE sessions.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.27.1.6 |
expedIfBssCpeHostVLANIDIndicates VLAN ID the Host is onro INTEGER .1.3.6.1.4.1.4743.1.2.2.27.1.7 |
expedIfBssVlanTableA set of objects in the BSS, maintained for each
CPE connected to this base station. SEQUENCE OF ExpedIfBssVlanEntry .1.3.6.1.4.1.4743.1.2.2.28 |
expedIfBssVlanEntryStats information for a single VLAN ID.
An entry in this table exists for each VLAN. ExpedIfBssVlanEntry .1.3.6.1.4.1.4743.1.2.2.28.1 |
expedIfBssVlanIndexIndex value to uniquely identify an entry in this table.
For an individual VLAN, this index value should
not change during BSS uptime.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.28.1.1 |
expedIfBssVlanNumOfCpesNumber of CPEs on this VLANro INTEGER .1.3.6.1.4.1.4743.1.2.2.28.1.2 |
expedIfBssVlanUpBytesNumber of uplink bytes for this VLAN.ro Counter .1.3.6.1.4.1.4743.1.2.2.28.1.3 |
expedIfBssVlanUpUnicastPktsNumber of uplink unicast packets for this VLAN.ro Counter .1.3.6.1.4.1.4743.1.2.2.28.1.4 |
expedIfBssVlanUpNUnicastPktsNumber of uplink broadcast packets for this VLAN.ro Counter .1.3.6.1.4.1.4743.1.2.2.28.1.5 |
expedIfBssVlanDnBytesNumber of downlink bytes for this VLAN.ro Counter .1.3.6.1.4.1.4743.1.2.2.28.1.6 |
expedIfBssVlanDnUnicastPktsNumber of downlink unicast packets for this VLAN.ro Counter .1.3.6.1.4.1.4743.1.2.2.28.1.7 |
expedIfBssVlanDnNUnicastPktsNumber of downlink broadcast packets for this VLAN.ro Counter .1.3.6.1.4.1.4743.1.2.2.28.1.8 |
expedIfBssVlanNumOfHostsNumber of hosts on this VLANro INTEGER .1.3.6.1.4.1.4743.1.2.2.28.1.9 |
expedIfBssCPERemoteStatsTableTable of remote snmp stats gatherered over the air from each CPE. SEQUENCE OF ExpedIfBssCPERemoteEntry .1.3.6.1.4.1.4743.1.2.2.29 |
expedIfBssCPERemoteEntryTable of remote snmp stats gatherered over the air from each CPE. ExpedIfBssCPERemoteEntry .1.3.6.1.4.1.4743.1.2.2.29.1 |
expedIfBssRemoteCPEIndexIndex value to uniquely identify an entry in this table.
For an individual CPE, this index value should
not change during BSS uptime.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.1 |
expedIfBssRemoteCPEMacAddressMac Address of the CPE being remotely monitored.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.2 |
expedIfBssRemoteCPEPollSuccessIndicates the success of the last poll. True indicates a succes,
False indicates SNMP was not able to get stats from the CPE.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.3 |
expedIfBssRemoteSlot1-SuccessNumber of messages successful on slot.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.4 |
expedIfBssRemoteSlot1-NoAccessNumber of message send failures due to uplink slot acquisition failure on slot.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.5 |
expedIfBssRemoteSlot1-FailedNumber of message send failures due to loss of uplink slot.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.6 |
expedIfBssRemoteSlot2-SuccessNumber of messages successful on slot.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.7 |
expedIfBssRemoteSlot2-NoAccessNumber of message send failures due to uplink slot acquisition failure on slot.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.8 |
expedIfBssRemoteSlot2-FailedNumber of message send failures due to loss of uplink slot.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.9 |
expedIfBssRemoteSlot3-SuccessNumber of messages successful on slot.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.10 |
expedIfBssRemoteSlot3-NoAccessNumber of message send failures due to uplink slot acquisition failure on slot.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.11 |
expedIfBssRemoteSlot3-FailedNumber of message send failures due to loss of uplink slot.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.12 |
expedIfBssRemoteSlot4-SuccessNumber of messages successful on slotro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.13 |
expedIfBssRemoteSlot4-NoAccessNumber of message send failures due to uplink slot acquisition failure on slot.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.14 |
expedIfBssRemoteSlot4-FailedNumber of message send failures due to loss of uplink slot.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.15 |
expedIfBssRemoteSlot5-SuccessNumber of messages successful on slotro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.16 |
expedIfBssRemoteSlot5-NoAccessNumber of message send failures due to uplink slot acquisition failure on slot.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.17 |
expedIfBssRemoteSlot5-FailedNumber of message send failures due to loss of uplink slot.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.18 |
expedIfBssRemoteSlot6-SuccessNumber of messages successful on slot.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.19 |
expedIfBssRemoteSlot6-NoAccessNumber of message send failures due to uplink slot acquisition failure on slot.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.20 |
expedIfBssRemoteSlot6-FailedNumber of message send failures due to loss of uplink slot.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.21 |
expedIfBssRemoteSlot1-ACKNumber of successful symbol transmissions.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.22 |
expedIfBssRemoteSlot1-NACKNumber of symbol retries.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.23 |
expedIfBssRemoteSlot1-BusyNumber of slot acquisition backoff due to slot busy.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.24 |
expedIfBssRemoteSlot1-FreeNumber of slot acquisition failures.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.25 |
expedIfBssRemoteSlot1-LostNumber of slot failures due to lost contention.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.26 |
expedIfBssRemoteSlot1-AttemptNumber of slot acquisitions.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.27 |
expedIfBssRemoteSlot2-ACKNumber of successful symbol transmissions.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.28 |
expedIfBssRemoteSlot2-NACKNumber of symbol retries.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.29 |
expedIfBssRemoteSlot2-BusyNumber of slot acquisition backoff due to slot busy.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.30 |
expedIfBssRemoteSlot2-FreeNumber of slot acquisition failures.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.31 |
expedIfBssRemoteSlot2-LostNumber of slot failures due to lost contention.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.32 |
expedIfBssRemoteSlot2-AttemptNumber of slot acquisitions.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.33 |
expedIfBssRemoteSlot3-ACKNumber of successful symbol transmissions.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.34 |
expedIfBssRemoteSlot3-NACKNumber of symbol retries.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.35 |
expedIfBssRemoteSlot3-BusyNumber of slot acquisition backoff due to slot busy.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.36 |
expedIfBssRemoteSlot3-FreeNumber of slot acquisition failures.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.37 |
expedIfBssRemoteSlot3-LostNumber of slot failures due to lost contention.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.38 |
expedIfBssRemoteSlot3-AttemptNumber of slot acquisitions.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.39 |
expedIfBssRemoteSlot4-ACKNumber of successful symbol transmissions.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.40 |
expedIfBssRemoteSlot4-NACKNumber of symbol retries.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.41 |
expedIfBssRemoteSlot4-BusyNumber of slot acquisition backoff due to slot busy.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.42 |
expedIfBssRemoteSlot4-FreeNumber of slot acquisition failures.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.43 |
expedIfBssRemoteSlot4-LostNumber of slot failures due to lost contention.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.44 |
expedIfBssRemoteSlot4-AttemptNumber of slot acquisitions.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.45 |
expedIfBssRemoteSlot5-ACKNumber of successful symbol transmissions.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.46 |
expedIfBssRemoteSlot5-NACKNumber of symbol retries.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.47 |
expedIfBssRemoteSlot5-BusyNumber of slot acquisition backoff due to slot busy.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.48 |
expedIfBssRemoteSlot5-FreeNumber of slot acquisition failures.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.49 |
expedIfBssRemoteSlot5-LostNumber of slot failures due to lost contention.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.50 |
expedIfBssRemoteSlot5-AttemptNumber of slot acquisitions.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.51 |
expedIfBssRemoteSlot6-ACKNumber of successful symbol transmissions.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.52 |
expedIfBssRemoteSlot6-NACKNumber of symbol retries.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.53 |
expedIfBssRemoteSlot6-BusyNumber of slot acquisition backoff due to slot busy.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.54 |
expedIfBssRemoteSlot6-FreeNumber of slot acquisition failures.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.55 |
expedIfBssRemoteSlot6-LostNumber of slot failures due to lost contention.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.56 |
expedIfBssRemoteSlot6-AttemptNumber of slot acquisitions.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.57 |
expedIfBssRemoteGoodSymbolsNumber of good symbols received by the CPE.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.58 |
expedIfBssRemoteBadSymbolsNumber of bad symbols received by the CPE.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.59 |
expedIfBssRemoteUnderFlowsNumber of times the signal processor was in an underflow condition.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.60 |
expedIfBssRemoteOverFlowsNumber of times the signal processor was in an overflow condition.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.61 |
expedIfBssRemoteSymbolCountNumber of symbols evaluated to accumulate the score.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.62 |
expedIfBssRemoteBadSymbolCountNumber of bad symbols in the evaluation of the score.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.63 |
expedIfBssRemoteBERBit Error rate calculated during the score evaluation.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.64 |
expedIfBssRemoteAvRSSIAverage RSSI calculated during the score evaluation.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.65 |
expedIfBssRemoteAvVTAverage Viterbi calculated during the score evaluation.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.66 |
expedIfBssRemoteAccumRSReed Solomon errors calculated during the score evaluation.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.67 |
expedIfBssRemoteScoreAccumulated calculated score.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.68 |
expedIfBssRemoteAirConnectTimeIndicates how long the CPE has been connected to a base station.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.69 |
expedIfBssRemoteDiscDownlinkNumber of disconnects due to a downlink failure.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.70 |
expedIfBssRemoteDisconnectUpLinkNumber of disconnects due to a uplink failure.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.71 |
expedIfBssRemoteHomeColorCodeIndicates the home color code assigned to this CPE.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.72 |
expedIfBssRemoteExtendedRangeIndicates whether the CPE is enabled for extended range or not.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.73 |
expedIfBssRemoteRangingValueIndicates the maximum distance (range) the CPE will try to register at,
before moving on to a different base.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.74 |
expedIfBssRemoteTriggerValueThe actual trigger value that the signal processor is programmed with.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.75 |
expedIfBssRemoteCPEBaseObsCh1Channel of the base station observed by the CPE in the base observation table.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.76 |
expedIfBssRemoteCPEBaseObsMac1Mac address of the base station observed by the CPE in the observation table.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.77 |
expedIfBssRemoteCPEBaseObsCC1Color code of the base station observed by the CPE in the observation table.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.78 |
expedIfBssRemoteCPEBaseObsScore1Score of the base station observed by the CPE in the observation table.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.79 |
expedIfBssRemoteCPEBaseObsAuth1True indicates the CPE is authorized to use this base, False indicates that this CPE
has been denied by this base.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.80 |
expedIfBssRemoteCPEBaseObsBusy1True indicates this base observed is busy and is not recommending registrations to it.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.81 |
expedIfBssRemoteCPEBaseObsRang1True indicates the CPE has completed extended ranging with this base station.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.82 |
expedIfBssRemoteCPEBaseObsCh2Channel of the base station observed by the CPE in the base observation table.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.83 |
expedIfBssRemoteCPEBaseObsMac2Mac address of the base station observed by the CPE in the observation table.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.84 |
expedIfBssRemoteCPEBaseObsCC2Color code of the base station observed by the CPE in the observation table.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.85 |
expedIfBssRemoteCPEBaseObsScore2Score of the base station observed by the CPE in the observation table.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.86 |
expedIfBssRemoteCPEBaseObsAuth2True indicates the CPE is authorized to use this base, False indicates that this CPE
has been denied by this base.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.87 |
expedIfBssRemoteCPEBaseObsBusy2True indicates this base observed is busy and is not recommending registrations to it.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.88 |
expedIfBssRemoteCPEBaseObsRang2True indicates the CPE has completed extended ranging with this base station.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.89 |
expedIfBssRemoteCPEBaseObsCh3Channel of the base station observed by the CPE in the base observation table.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.90 |
expedIfBssRemoteCPEBaseObsMac3Mac address of the base station observed by the CPE in the observation table.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.91 |
expedIfBssRemoteCPEBaseObsCC3Color code of the base station observed by the CPE in the observation table.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.92 |
expedIfBssRemoteCPEBaseObsScore3Score of the base station observed by the CPE in the observation table.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.93 |
expedIfBssRemoteCPEBaseObsAuth3True indicates the CPE is authorized to use this base, False indicates that this CPE
has been denied by this base.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.94 |
expedIfBssRemoteCPEBaseObsBusy3True indicates this base observed is busy and is not recommending registrations to it.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.95 |
expedIfBssRemoteCPEBaseObsRang3True indicates the CPE has completed extended ranging with this base station.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.96 |
expedIfBssRemoteCPEBaseObsCh4Channel of the base station observed by the CPE in the base observation table.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.97 |
expedIfBssRemoteCPEBaseObsMac4Mac address of the base station observed by the CPE in the observation table.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.98 |
expedIfBssRemoteCPEBaseObsCC4Color code of the base station observed by the CPE in the observation table.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.99 |
expedIfBssRemoteCPEBaseObsScore4Score of the base station observed by the CPE in the observation table.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.100 |
expedIfBssRemoteCPEBaseObsAuth4True indicates the CPE is authorized to use this base, False indicates that this CPE
has been denied by this base.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.101 |
expedIfBssRemoteCPEBaseObsBusy4True indicates this base is observed busy and is not recommending registrations to it.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.102 |
expedIfBssRemoteCPEBaseObsRang4True indicates the CPE has completed extended ranging with this base station.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.103 |
expedIfBssRemoteCPEBaseObsCh5Channel of the base station observed by the CPE in the base observation table.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.104 |
expedIfBssRemoteCPEBaseObsMac5Mac address of the base station observed by the CPE in the observation table.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.105 |
expedIfBssRemoteCPEBaseObsCC5Color code of the base station observed by the CPE in the observation table.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.106 |
expedIfBssRemoteCPEBaseObsScore5Score of the base station observed by the CPE in the observation table.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.107 |
expedIfBssRemoteCPEBaseObsAuth5True indicates the CPE is authorized to use this base, False indicates that this CPE
has been denied by this base.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.108 |
expedIfBssRemoteCPEBaseObsBusy5True indicates this base observed is busy and is not recommending registrations to it.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.109 |
expedIfBssRemoteCPEBaseObsRang5True indicates the CPE has completed extended ranging with this base station.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.110 |
expedIfBssRemoteCPEBaseObsCh6Channel of the base station observed by the CPE in the base observation table.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.111 |
expedIfBssRemoteCPEBaseObsMac6Mac address of the base station observed by the CPE in the observation table.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.112 |
expedIfBssRemoteCPEBaseObsCC6Color code of the base station observed by the CPE in the observation table.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.113 |
expedIfBssRemoteCPEBaseObsScore6Score of the base station observed by the CPE in the observation table.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.114 |
expedIfBssRemoteCPEBaseObsAuth6True indicates the CPE is authorized to use this base, False indicates that this CPE
has been denied by this base.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.115 |
expedIfBssRemoteCPEBaseObsBusy6True indicates this base observed is busy and is not recommending registrations to it.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.116 |
expedIfBssRemoteCPEBaseObsRang6True indicates the CPE has completed extended ranging with this base station.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.117 |
expedIfBssRemoteCPENumActCallsNumber of active calls on the CPE.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.118 |
expedIfBssRemoteCPEDataPollsNumber Of Data Polls for this CPEro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.119 |
expedIfBssRemoteCPEDryPollsNumber Of Dry Polls for this CPEro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.120 |
expedIfBssRemoteCPEUnexpectedNumber Of Unexpected Polls for this CPEro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.121 |
expedIfBssRemoteCPEBWUsageSync Session Bandwidth Usage for all calls on this CPE from the
perspective of CPEro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.122 |
expedIfBssRemoteCPEEfficiencyEfficiency use of bandwidth for all calls on this CPEro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.123 |
expedIfBssRemoteCPEHighWaterHighest Queue Depth for call symbols.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.124 |
expedIfBssRemoteCPEVoiceFrRtRate of packets received over the Ethernet for Voice Call.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.125 |
expedIfBssRemoteCPEAvgNPIAvg Next Poll Interval (NPI). This tells the base
how often the CPE wants to be polled.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.126 |
expedIfBssRemoteCPEConcatBuffersNumber of times concatenation took place on the uplink.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.127 |
expedIfBssRemoteCPENumBufConcatNumber of ethernet frames that were concatenated together.ro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.128 |
expedIfBssRemoteCPECurrentTempCurrent Temperature on the CPE in Celsius. A value of -273
indicates that the CPE has no temperature sensor.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.129 |
expedIfBssRemoteCPETxPowerCurrent Transmit power on the CPE in dB. A value of 0
indicates that the CPE has no power sensor.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.29.1.130 |
expedIfBssRemoteCPEQPSKUpNumber of bytes on the uplink at QPSK modulation levelro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.131 |
expedIfBssRemoteCPEQPSKDownNumber of bytes on the downlink at QPSK modulation levelro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.132 |
expedIfBssRemoteCPE16QUpNumber of bytes on the uplink at 16 QAM modulation levelro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.133 |
expedIfBssRemoteCPE16QDownNumber of bytes on the downlink at 16 QAM modulation levelro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.134 |
expedIfBssRemoteCPE64QUpNumber of bytes on the uplink at 64 QAM modulation levelro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.135 |
expedIfBssRemoteCPE64QDownNumber of bytes on the downlink at 64 QAM modulation levelro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.136 |
expedIfBssRemoteCPE16QLiteUpNumber of bytes on the uplink at 16 QAM Lite modulation levelro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.137 |
expedIfBssRemoteCPE16QLiteDownNumber of bytes on the downlink at 16 QAM Lite modulation levelro Counter .1.3.6.1.4.1.4743.1.2.2.29.1.138 |
expedIfBssRemoteCurrentRxLevelCurrent RX Modulation Levelro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.139 |
expedIfBssRemoteCurrentTxLevelCurrent TX Modulation Levelro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.29.1.140 |
expedIfBssRemotePollIntervalIndicates how often each CPE in the BssRemoteCPE table will be queried for
over the air SNMP stats.rw INTEGER .1.3.6.1.4.1.4743.1.2.2.30 |
expedIfBssRemotePollTimeoutIndicates how long to wait for an over the air SNMP query to complete before
indicating that the Poll was unsuccessful.rw INTEGER .1.3.6.1.4.1.4743.1.2.2.31 |
expedIfBssAAADroppedCDRSNumber of CDR's dropped due to out of buffer condition.ro Counter .1.3.6.1.4.1.4743.1.2.2.32 |
expedIfBssNoResToPollTimeoutNumber of seconds to wait for a Response to a Poll before
tearing down the call.rw INTEGER .1.3.6.1.4.1.4743.1.2.2.33 |
expedIfBssMaxNumberOfCallsMaximum number of calls this base has been provisioned for.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.34 |
expedIfBssCurrentNumberOfCallsCurrent number of active calls on this base.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.35 |
expedIfBssQPSKCpesCurrent number of CPEs with downlink modulation at QPSK.
This object is obsolete as of base station software version 4.3
and is replaced by expedIfBssModTbl.roobsolete Counter .1.3.6.1.4.1.4743.1.2.2.36 |
expedIfBss16QAMCpesCurrent number of CPEs with downlink modulation at 16 QAM.
This object is obsolete as of base station software version 4.3
and is replaced by expedIfBssModTbl.roobsolete Counter .1.3.6.1.4.1.4743.1.2.2.37 |
expedIfBss64QAMCpesCurrent number of CPEs with downlink modulation at 64 QAM.
This object is obsolete as of base station software version 4.3
and is replaced by expedIfBssModTbl.roobsolete Counter .1.3.6.1.4.1.4743.1.2.2.38 |
expedIfBss16QAMLiteCpesCurrent number of CPEs with downlink modulation at 16 QAMLite.
This object is obsolete as of base station software version 4.3
and is replaced by expedIfBssModTbl.roobsolete Counter .1.3.6.1.4.1.4743.1.2.2.39 |
expedIfBssQPSKDownBytesTotal number of QPSK bytes sent from the base on the downlink.
This object is obsolete as of base station software version 4.3
and is replaced by expedIfBssModTbl.roobsolete Counter .1.3.6.1.4.1.4743.1.2.2.40 |
expedIfBssQPSKUpBytesTotal number of QPSK bytes received by the base on the uplink.
This object is obsolete as of base station software version 4.3
and is replaced by expedIfBssModTbl.roobsolete Counter .1.3.6.1.4.1.4743.1.2.2.41 |
expedIfBss16QAMDownBytesTotal number of 16 QAM bytes sent from the base on the downlink.
This object is obsolete as of base station software version 4.3
and is replaced by expedIfBssModTbl.roobsolete Counter .1.3.6.1.4.1.4743.1.2.2.42 |
expedIfBss16QAMUpBytesTotal number of 16 QAM bytes received by the base on the uplink.
This object is obsolete as of base station software version 4.3
and is replaced by expedIfBssModTbl.roobsolete Counter .1.3.6.1.4.1.4743.1.2.2.43 |
expedIfBss64QAMDownBytesTotal number of 64 QAM bytes sent from the base on the downlink.
This object is obsolete as of base station software version 4.3
and is replaced by expedIfBssModTbl.roobsolete Counter .1.3.6.1.4.1.4743.1.2.2.44 |
expedIfBss64QAMUpBytesTotal number of 64 QAM bytes received by the base on the uplink.
This object is obsolete as of base station software version 4.3
and is replaced by expedIfBssModTbl.roobsolete Counter .1.3.6.1.4.1.4743.1.2.2.45 |
expedIfBss16QAMLiteDownBytesTotal number of 16 QAM Lite bytes sent from the base on the
downlink.
This object is obsolete as of base station software version 4.3
and is replaced by expedIfBssModTbl.roobsolete Counter .1.3.6.1.4.1.4743.1.2.2.46 |
expedIfBss16QAMLiteUpBytesTotal number of 16 QAM Lite bytes received by the base on the
uplink.
This object is obsolete as of base station software version 4.3
and is replaced by expedIfBssModTbl.roobsolete Counter .1.3.6.1.4.1.4743.1.2.2.47 |
expedIfBssRelayIPHostsThe current number of dynamic hosts that have IP access using DHCP.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.48 |
expedIfBssRelayPPPOEHostsThe current number of dynamic hosts that have PPPoE access. This count does not
include PPPoE access by static IP hosts.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.49 |
expedIfBssLocalAllowThe permission the Local Authority gives to each CPE, where
enable allows CPEs to register, and disable disallows CPEs to
register. Note: When a CPE is disallowed the CPE must be
rebooted in order to register with this base station again.
This defaults to enablerw Enumeration .1.3.6.1.4.1.4743.1.2.2.50 |
expedIfBssLocalHostsThe number of hosts Local Authority allows behind each CPE.
This defaults to 10rw INTEGER .1.3.6.1.4.1.4743.1.2.2.51 |
expedIfBssLocalSlaThe Service Level Agreement (SLA) parameters given to each CPE.
This is of the form up-down, where up and down are decimal numbers
between 0 and 10000, inclusive, separated by a dash character.
This defaults to 100-100.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.52 |
expedIfBssLocalVlanThe VLAN identifier Local Authority assigns to each CPE.
This object replaces the expedDevVlanLegacyID object.
This defaults to 1.rw INTEGER .1.3.6.1.4.1.4743.1.2.2.53 |
expedIfBssLocalVoipAddressThe VoIP server address Local Authority assigns to each CPE.
allows the VoIP use through the CPE and disable disallows VoIP
use through the CPE. This defaults to 0.0.0.0.rw IpAddress .1.3.6.1.4.1.4743.1.2.2.54 |
expedIfBssLocalVoipStateThe VoIP state Local Authority assigns to each CPE, where enable
allows the VoIP use through the CPE and disable disallows VoIP
use through the CPE. This defaults to enable.rw Enumeration .1.3.6.1.4.1.4743.1.2.2.55 |
expedIfBssModTblTable of stats for throughput at each modulation. SEQUENCE OF ExpedIfBssModTblEntry .1.3.6.1.4.1.4743.1.2.2.56 |
expedIfBssModTblEntryTable of stats for throughput at each modulation. ExpedIfBssModTblEntry .1.3.6.1.4.1.4743.1.2.2.56.1 |
expedIfBssModTblIndexIndex for each modulationro INTEGER .1.3.6.1.4.1.4743.1.2.2.56.1.1 |
expedIfBssModTblNameDescriptive name for the modulation.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.56.1.2 |
expedIfBssModTblUpSlotUsageTotal uplink slots at each modulation.ro Counter .1.3.6.1.4.1.4743.1.2.2.56.1.3 |
expedIfBssModTblUpSlotVOIPTotal uplink slots for voip at each modulation.ro Counter .1.3.6.1.4.1.4743.1.2.2.56.1.4 |
expedIfBssModTblUpBytesTotal uplink bytes at each modulation.ro Counter .1.3.6.1.4.1.4743.1.2.2.56.1.5 |
expedIfBssModTblUpMessagesTotal uplink messages at each modulation.ro Counter .1.3.6.1.4.1.4743.1.2.2.56.1.6 |
expedIfBssModTblDownSlotUsageTotal downlink slot usage at each modulation.ro Counter .1.3.6.1.4.1.4743.1.2.2.56.1.7 |
expedIfBssModTblDownBytesTotal downlink bytes at each modulation (includes VoIP bytes).ro Counter .1.3.6.1.4.1.4743.1.2.2.56.1.8 |
expedIfBssModTblNumCPESNumber CPEs at each modulation.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.56.1.9 |
expedIfBssModTblChgReqsNumber change modulation requests received for each modulation.ro Counter .1.3.6.1.4.1.4743.1.2.2.56.1.10 |
expedIfBssModTblDownBytesVOIPTotal VoIP downlink bytes at each modulation.ro Counter .1.3.6.1.4.1.4743.1.2.2.56.1.11 |
expedIfBssModTblUpBytesVOIPTotal VoIP uplink bytes at each modulation.ro Counter .1.3.6.1.4.1.4743.1.2.2.56.1.12 |
expedIfBssModUpSlotsPerSecTotal uplink slots per second.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.57 |
expedIfBssModDownSlotsPerSecTotal down slots per second.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.58 |
expedIfBssAAAAllowTotal number of allow PV's.ro Counter .1.3.6.1.4.1.4743.1.2.2.59 |
expedIfBssAAADenyTotal number of deny PV's.ro Counter .1.3.6.1.4.1.4743.1.2.2.60 |
expedIfBssAAADeregCPETotal number of de-reg CPE PV's.ro Counter .1.3.6.1.4.1.4743.1.2.2.61 |
expedIfBssAAABindIPTotal number of bind IP PV's.ro Counter .1.3.6.1.4.1.4743.1.2.2.62 |
expedIfBssAAAPutConfigTotal number of put config PV's.ro Counter .1.3.6.1.4.1.4743.1.2.2.63 |
expedIfBssAAAFetchConfigTotal number of fetch config PV's.ro Counter .1.3.6.1.4.1.4743.1.2.2.64 |
expedIfBssAAAUnkBaseTotal number of unknown base PV's.ro Counter .1.3.6.1.4.1.4743.1.2.2.65 |
expedIfBssAAAVlanAttsTotal number of VLAN attribute PV's.ro Counter .1.3.6.1.4.1.4743.1.2.2.66 |
expedIfBssAAABaseAttsTotal number of base attribute PV's.ro Counter .1.3.6.1.4.1.4743.1.2.2.67 |
expedIfBssAAAReconnectTotal number of reconnect to primary AAA PV's.ro Counter .1.3.6.1.4.1.4743.1.2.2.68 |
expedIfBssAAAHbCdrTotal number of heartbeat messages (CDRs) sent.ro Counter .1.3.6.1.4.1.4743.1.2.2.69 |
expedIfBssAAAHbPvTotal number of heartbeat messages (PVs) received.ro Counter .1.3.6.1.4.1.4743.1.2.2.70 |
expedIfBssAAAHbIntervalHeartbeat interval received on the AAA connection.ro INTEGER .1.3.6.1.4.1.4743.1.2.2.71 |
expedIfBssAAAHbDisconnectsTotal number of times the heartbeat detector forced
disconnection from AAA due to timeout.ro Counter .1.3.6.1.4.1.4743.1.2.2.72 |
expedIfBssRelayMaxSSTransitThe max amount of time in 10ths of a second a sync session frame
can live within the device before it is considered stale and is
deleted.rw INTEGER .1.3.6.1.4.1.4743.1.2.2.73 |
expedIfBssRelayDHCPAgentCircuitIdIndicate whether a relay DHCP agent circuit id is attached to
all the client-to-server DHCP messages.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.74 |
expedIfBssRelayDHCPAgentRemoteIdIndicate whether a relay DHCP agent remote id is attached to
all the client-to-server DHCP messages.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.4743.1.2.2.75 |
expedIfBssRelayDHCPNumAddAgentFailThe number of failing to add agent circuit id and/or remote id
in the client-to-server DHCP packets due to not enough space in
the packets.ro Counter .1.3.6.1.4.1.4743.1.2.2.76 |
expedIfBssRelayDHCPNumDiscardExtraRelayInfoThe number of DHCP packets discarded due to the existing relay
agent information in the client-to-server DHCP packet when adding
DHCP agent circuit id and/or remote id to it.ro Counter .1.3.6.1.4.1.4743.1.2.2.77 |
expedIfBssRelayDHCPNumDiscardNoEndThe number of DHCP packets discarded due to DHCP_END option
missing when adding DHCP agent circuit id and/or remote id to
client-to-server DHCP packets.ro Counter .1.3.6.1.4.1.4743.1.2.2.78 |
expedIfBssAdmissionCtrlVoIP admission control. The enable of VoIP admission control
turns on the stream precedence and preemption capability.rw Enumeration .1.3.6.1.4.1.4743.1.2.2.79 |
expedIfBssNumberOfReleaseRetriesNumber of retransmission of Sync Session release message.rw INTEGER .1.3.6.1.4.1.4743.1.2.2.80 |
expedIfBssHiModulationControls whether or not high modulation can be used to transport
VoIP traffic on the uplink. When enabled, a transmitting CPE is
allowed to use a modulation higher than the basic QPSK modulation
level. When disabled, CPEs must use QPSK modulation for all
uplink VoIP data.
Note that this only controls uplink VoIP modulation.rw Enumeration .1.3.6.1.4.1.4743.1.2.2.81 |
expedIfBssNumOfCallPri0The total number of calls requested by a CPE on this base at
priority 0.ro Counter .1.3.6.1.4.1.4743.1.2.2.82 |
expedIfBssNumOfCallPri1The total number of calls requested by a CPE on this base at
priority 1.ro Counter .1.3.6.1.4.1.4743.1.2.2.83 |
expedIfBssNumOfCallPri2The total number of calls requested by a CPE on this base at
priority 2.ro Counter .1.3.6.1.4.1.4743.1.2.2.84 |
expedIfBssNumOfCallPri3The total number of calls requested by a CPE on this base at
priority 3.ro Counter .1.3.6.1.4.1.4743.1.2.2.85 |
expedIfBssNumOfCallPreemptedPri0The number of calls preempted at priority 0.ro Counter .1.3.6.1.4.1.4743.1.2.2.86 |
expedIfBssNumOfCallPreemptedPri1The number of calls preempted at priority 1.ro Counter .1.3.6.1.4.1.4743.1.2.2.87 |
expedIfBssNumOfCallPreemptedPri2The number of calls preempted at priority 2.ro Counter .1.3.6.1.4.1.4743.1.2.2.88 |
expedIfBssNumOfBusyCallOrigPri0The number of calls at priority 0 that is failed to make
due to originator VoIP busy.ro Counter .1.3.6.1.4.1.4743.1.2.2.89 |
expedIfBssNumOfBusyCallOrigPri1The number of calls at priority 1 that is failed to make
due to originator VoIP busy.ro Counter .1.3.6.1.4.1.4743.1.2.2.90 |
expedIfBssNumOfBusyCallOrigPri2The number of calls at priority 2 that is failed to make
due to originator VoIP busy.ro Counter .1.3.6.1.4.1.4743.1.2.2.91 |
expedIfBssNumOfBusyCallOrigPri3The number of calls at priority 3 that is failed to make
due to originator VoIP busy.ro Counter .1.3.6.1.4.1.4743.1.2.2.92 |
expedIfBssNumOfBusyCallTermPri0The number of calls at priority 0 that is failed to make
due to terminator VoIP busy.ro Counter .1.3.6.1.4.1.4743.1.2.2.93 |
expedIfBssNumOfBusyCallTermPri1The number of calls at priority 1 that is failed to make
due to terminator VoIP busy.ro Counter .1.3.6.1.4.1.4743.1.2.2.94 |
expedIfBssNumOfBusyCallTermPri2The number of calls at priority 2 that is failed to make
due to terminator VoIP busy.ro Counter .1.3.6.1.4.1.4743.1.2.2.95 |
expedIfBssNumOfBusyCallTermPri3The number of calls at priority 3 that is failed to make
due to terminator VoIP busy.ro Counter .1.3.6.1.4.1.4743.1.2.2.96 |
expedIfBssNumOfVoIPNotAllowOrigThe number of calls that is failed to make due to
originator cpe not provisioned.ro Counter .1.3.6.1.4.1.4743.1.2.2.97 |
expedIfBssNumOfVoIPNotAllowTermThe number of calls that is failed to make due to
terminator cpe not provisioned.ro Counter .1.3.6.1.4.1.4743.1.2.2.98 |
expedIfBssNumOfVoIPNotAuthOrigThe number of calls that is failed to make due to
originator cpe requesting a wrong SIP server.ro Counter .1.3.6.1.4.1.4743.1.2.2.99 |
expedIfBssNumOfVoIPNotAuthTermThe number of calls that is failed to make due to
terminator cpe requesting a wrong SIP server.ro Counter .1.3.6.1.4.1.4743.1.2.2.100 |
expedIfBssNumOfCallRoamPri0The total number of calls roamed to this base at priority 0.ro Counter .1.3.6.1.4.1.4743.1.2.2.101 |
expedIfBssNumOfCallRoamPri1The total number of calls roamed to this base at priority 1.ro Counter .1.3.6.1.4.1.4743.1.2.2.102 |
expedIfBssNumOfCallRoamPri2The total number of calls roamed to this base at priority 2.ro Counter .1.3.6.1.4.1.4743.1.2.2.103 |
expedIfBssNumOfCallRoamPri3The total number of calls roamed to this base at priority 3.ro Counter .1.3.6.1.4.1.4743.1.2.2.104 |
expedDevTrap OBJECT IDENTIFIER .1.3.6.1.4.1.4743.2 |
expedDevTrapVars OBJECT IDENTIFIER .1.3.6.1.4.1.4743.2.3 |
expedDevTrapBTSNameSystem name of the BTS sending the trap.
This object is obsolete as of base station software version 4.3
and has no replacement.roobsolete DisplayString .1.3.6.1.4.1.4743.2.3.1 |
expedDevTrapBTSLocationSystem location of the BTS sending the trap.
This object is obsolete as of base station software version 4.3
and has no replacement.roobsolete DisplayString .1.3.6.1.4.1.4743.2.3.2 |
expedDevTrapBTSMessageMessage that is accompanying the trap.
This object is obsolete as of base station software version 4.3
and has no replacement.roobsolete DisplayString .1.3.6.1.4.1.4743.2.3.3 |