MOXA-W2x50A-MIB
AI MIB Summary
The MOXA-W2x50A-MIB module enables SNMP-based monitoring and management of Moxa NPort W2x50A wireless serial device servers, exposing vendor-specific metrics such as cellular signal strength (RSSI/SNR), SIM status, IP connectivity states, and serial port session statistics.
The MIB module for Moxa NPort W2x50A series specific information.
Main OID:
w2x50A.1.3.6.1.4.1.8691.2.13
346
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
346 total| Object Name |
|---|
moxa OBJECT IDENTIFIER .1.3.6.1.4.1.8691 |
nport OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2 |
w2x50AThe MIB module for Moxa NPort W2x50A series specific information. MODULE-IDENTITY .1.3.6.1.4.1.8691.2.13 |
swMgmt OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1 |
overview OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.1 |
modelNameThe model name of the NPort. The possible values
of this parameter are:
'NPort W2x50A' for NPort W2x50A.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.1.1 |
serialNumberThe serial number of the NPort. Every NPort
W2x50A series device server is assigned a unique serial
number before it is shipped.ro INTEGER .1.3.6.1.4.1.8691.2.13.1.1.2 |
firmwareVersionThe version of the firmware currently running on
the NPort.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.1.3 |
ethIPAddressThe IP address of the NPort's Ethernet interface.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.1.4 |
ethMacAddressThe MAC address of the NPort's Ethernet interface.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.1.5 |
wlanIPAddressThe IP address of the NPort's WLAN interface.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.1.6 |
wlanMacAddressThe MAC address of the NPort's WLAN interface.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.1.7 |
wlanSSIDThe SSID of WLAN.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.1.8 |
wlanNetworkTypeNetwork Type of Wireless LAN. The possible values are
'Infrastrcture Mode' and 'Ad-hoc Mode'ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.1.9 |
wlanSecurityModeSecurity mode of Wireless LAN. The possible values are
'Open System', 'Shared Key', 'WPA', 'WPA-PSK', 'WPA2', 'WPA2-PSK'ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.1.10 |
wlanRFTypeRF type of Wireless LAN. The possible values are
'Auto', '802.11b', '802.11g'ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.1.11 |
wlanCountryCodeWLAN country codero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.1.12 |
wlanFastRoamingFast roaming statero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.1.13 |
activeNetworkPortCurrent active network port. The possible values are
'WLAN', 'Ethernet'ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.1.14 |
upTimeThe time (in human-readable notation) since the
system was last re-initialized.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.1.15 |
serialPort1View NPort's serial port 1 setting.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.1.16 |
serialPort2View NPort's serial port 2 setting.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.1.17 |
basicSetting OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.2 |
serverSetting OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.2.1 |
serverNameA text string used to identify the NPort.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.2.1.1 |
serverLocationA text string used to identify the location of the NPort. This
option is useful for specifying the location or
application of different NPort device servers.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.2.1.2 |
timeSetting OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.2.2 |
timeZoneThe time-zone index of the NPort.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.2.2.1 |
localTimeThe system time in the following format
yyyy/mm/dd hh:mm:ssrw DisplayString .1.3.6.1.4.1.8691.2.13.1.2.2.2 |
timeServerThe NPort W2x50A series device server uses SNTP
(RFC-1769) for auto time calibration.
Input the correct 'Time server' IP address or domain
name. Once the NPort W2x50A series device server
is configured with the correct Time server address,
it will request time information from the Time server
every 10 minutes.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.2.2.3 |
networkSetting OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.3 |
generalSetting OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.3.1 |
dnsServer1IpAddrThe first DNS server address. When the user wants
to visit a particular website, the computer asks a
Domain Name System (DNS) server for the website's
correct IP address, and then the computer uses the
response to connect to the web server. DNS is the
way that Internet domain names are identified and
translated into IP addresses. A domain name is an
alphanumeric name, such as moxa.com, that it is
usually easier to remember. A DNS server is a host
that translates this kind of text-based domain name
into the numeric IP address used to establish a
TCP/IP connection.rw IpAddress .1.3.6.1.4.1.8691.2.13.1.3.1.1 |
dnsServer2IpAddrThe second DNS server address. When the user wants
to visit a particular website, the computer asks a
Domain Name System (DNS) server for the website's
correct IP address, and then the computer uses the
response to connect to the web server. DNS is the
way that Internet domain names are identified and
translated into IP addresses. A domain name is an
alphanumeric name, such as moxa.com, that it is
usually easier to remember. A DNS server is a host
that translates this kind of text-based domain name
into the numeric IP address used to establish a
TCP/IP connection.rw IpAddress .1.3.6.1.4.1.8691.2.13.1.3.1.2 |
ethernetSetting OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.3.2 |
ethIpConfigurationThe IP configuration mode of the NPort. You can
choose from four possible IP configuration modes:
Static, DHCP, DHCP/BOOTP, BOOTP.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.2.1 |
ethIpAddressAn IP address is a number assigned to a network
device (such as a computer) as a permanent address
on the network. Computers use the IP address to
identify and talk to each other over the network.
Choose a proper IP address that is unique and valid
in your network environment.rw IpAddress .1.3.6.1.4.1.8691.2.13.1.3.2.2 |
ethNetMaskA subnet mask represents all of the network hosts
at one geographic location, in one building, or on
the same local area network. When a packet is sent
out over the network, the NPort W2x50A series
device server will use the subnet mask to check
whether the TCP/IP host specified in the packet is
on the local network segment. If the address is on
the same network segment as the NPort W2x50A
series device server, a connection is established
directly from the NPort W2x50A series device
server. Otherwise, the connection is established
through the given default gateway.rw IpAddress .1.3.6.1.4.1.8691.2.13.1.3.2.3 |
ethDefaultGatewayA gateway is a network computer that acts as an
entrance to another network. Usually, the computers
that control traffic within the network or at the
local Internet service provider are gateway nodes.
The NPort W2x50A series device server needs to
know the IP address of the default gateway computer
in order to communicate with the hosts outside the
local network environment. For correct gateway IP
address information, consult with the network
administrator.rw IpAddress .1.3.6.1.4.1.8691.2.13.1.3.2.4 |
ethBridgeModeEnable or disable the bridge function.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.2.5 |
wlanSetting OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.3.3 |
wlanIpConfigurationThe IP configuration mode of the NPort. You can
choose from four possible IP configuration modes:
Static, DHCP, DHCP/BOOTP, BOOTP.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.3.1 |
wlanIpAddressAn IP address is a number assigned to a network
device (such as a computer) as a permanent address
on the network. Computers use the IP address to
identify and talk to each other over the network.
Choose a proper IP address that is unique and valid
in your network environment.rw IpAddress .1.3.6.1.4.1.8691.2.13.1.3.3.2 |
wlanNetMaskA subnet mask represents all of the network hosts
at one geographic location, in one building, or on
the same local area network. When a packet is sent
out over the network, the NPort W2x50A series
device server will use the subnet mask to check
whether the TCP/IP host specified in the packet is
on the local network segment. If the address is on
the same network segment as the NPort W2x50A
series device server, a connection is established
directly from the NPort W2x50A series device
server. Otherwise, the connection is established
through the given default gateway.rw IpAddress .1.3.6.1.4.1.8691.2.13.1.3.3.3 |
wlanDefaultGatewayA gateway is a network computer that acts as an
entrance to another network. Usually, the computers
that control traffic within the network or at the
local Internet service provider are gateway nodes.
The NPort W2x50A series device server needs to
know the IP address of the default gateway computer
in order to communicate with the hosts outside the
local network environment. For correct gateway IP
address information, consult with the network
administrator.rw IpAddress .1.3.6.1.4.1.8691.2.13.1.3.3.4 |
profileSetting OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.3.4 |
networkTypeSelect WLAN network type.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.1 |
adhocProfile OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.3.4.2 |
adhocGeneralSetting OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.3.4.2.1 |
adhocProfileNameAssign profile name.rw DisplayString .1.3.6.1.4.1.8691.2.13.1.3.4.2.1.1 |
adhocRFTypeSelect WLAN network type.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.2.1.2 |
adhocWlanSSIDSet WLAN SSIDrw DisplayString .1.3.6.1.4.1.8691.2.13.1.3.4.2.1.3 |
adhocChannelDisplay currently used channel. When in Ad-Hoc mode, this value can be set.
mode region possible channel
======================================
802.11b_g : 1, 2, 3, 4, 5, 7, 8, 9, 10, 11, 12, 13rw INTEGER .1.3.6.1.4.1.8691.2.13.1.3.4.2.1.4 |
adhocSecuritySetting OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.3.4.2.2 |
adhocAuthenticationWireless LAN autentication type.ro Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.2.2.1 |
adhocEncryptionSet encryption type.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.2.2.2 |
adhocWepKeyLengthWEP key length.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.2.2.3 |
adhocWepKeyIndexWEP key index 1~4.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.3.4.2.2.4 |
adhocWepKeyPassphraseWEP key passphrase.rw DisplayString .1.3.6.1.4.1.8691.2.13.1.3.4.2.2.5 |
adhocWepKeyFormatWEP key format.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.2.2.6 |
infrastructureProfile OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.3.4.3 |
infraGeneralSetting OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.3.4.3.1 |
infraGeneralSettingTableWLAN profile general setting table. SEQUENCE OF InfraGeneralSettingEntry .1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1 |
infraGeneralSettingEntryWLAN profile general setting entry. InfraGeneralSettingEntry .1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1.1 |
profileIndexThe profile indexro Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1.1.1 |
profileNameAssign profile name.rw DisplayString .1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1.1.2 |
profileRFTypeSelect WLAN network type.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1.1.3 |
profileWlanSSIDSet WLAN SSIDrw DisplayString .1.3.6.1.4.1.8691.2.13.1.3.4.3.1.1.1.4 |
securitySetting OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.3.4.3.2 |
securitySettingTableWLAN profile security setting table. SEQUENCE OF SecuritySettingEntry .1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1 |
securitySettingEntryWLAN profile security setting entry. SecuritySettingEntry .1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1 |
authenticationWireless LAN autentication type.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.1 |
encryptionSet encryption type. Selection rule is as following.
authentication selectable encryption
============== =====================
open-system(0) disable(0), wep(1)
shared-key(1) wep(1)
wpa(2), wpa-psk(3) tkip(2), aes-ccmp(3)
wpa2(4), wpa2-psk(5) tkip(2), aes-ccmp(3)rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.2 |
wepKeyLengthWEP key length.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.3 |
wepKeyIndexWEP key index 1~4.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.4 |
wepKeyPassphraseWEP key passphrase.rw DisplayString .1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.5 |
wepKeyFormatWEP key format.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.6 |
eapMethodEAP method for WPA and WPA2 authentication.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.12 |
tunneledAuthSet tunneled authentication protocol when PEAP/TTLS is selected as EAP method.
EAP method selectable tunneled authentication
========== ==================================
peap(1) gtc(0), md5(1), mschapv2(5)
ttls(2) pap(2), chap(3), mschap(4), mschapv2(5),
eap-mschapv2(8), eap-gtc(9), eap-md5(10)rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.13 |
wpaUsernameWPA username for WPA and WPA2 authentication.rw DisplayString .1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.14 |
wpaAnonymousUsernameAnonymous username needed when TTLS is selected as EAP method.rw DisplayString .1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.16 |
verifyServerCertThe setting of verify server certificate.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.17 |
trustedServerCertDisplay whether or not trusted server certificate is installed.ro Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.18 |
userCertDisplay whether or not user certificate is installed.ro Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.19 |
userPrivateKeyDisplay whether or not user private key is installed.ro Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.3.2.1.1.20 |
fastRoamingSettingThe setting of fast roaming.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.3.3 |
fastRoamingScanChannels1The scan channels of fast roaming. 0 represents 'N/A'
======================================================
Auot channel : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165
802.11a, 802.11a_n : 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165
802.11b_g, 802.11b_g_n : 1, 2, 3, 4, 5, 7, 8, 9, 10, 11, 12, 13rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.3.4 |
fastRoamingScanChannels2The scan channels of fast roaming. 0 represents 'N/A'
======================================================
Auot channel : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165
802.11a, 802.11a_n : 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165
802.11b_g, 802.11b_g_n : 1, 2, 3, 4, 5, 7, 8, 9, 10, 11, 12, 13rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.3.5 |
fastRoamingScanChannels3The scan channels of fast roaming. 0 represents 'N/A'
======================================================
Auot channel : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165
802.11a, 802.11a_n : 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165
802.11b_g, 802.11b_g_n : 1, 2, 3, 4, 5, 7, 8, 9, 10, 11, 12, 13rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.4.3.6 |
fastRoamingThresholdRoaming threshold of fast roamingrw INTEGER (-70..-40) .1.3.6.1.4.1.8691.2.13.1.3.4.3.7 |
fastRoamingDifferenceRoaming difference of fast roamingrw INTEGER .1.3.6.1.4.1.8691.2.13.1.3.4.3.8 |
wlanLogSetting OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.3.5 |
wlanLogEnableEnable or disable WLAN logrw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.5.1 |
advancedSetting OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.3.6 |
gratuitousArpEnable or disable the gratuitous ARP function. For some
applications, users need the NPort W2x50A series
device server to send broadcast packets to update
the ARP table on the server. If the customer enables
this function and sets the send period, the NPort W2x50A
series device server will send broadcast
packets periodically.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.3.6.1 |
gratuitousArpSendPeriodThe send period of the gratuitous ARP function.
Range: 10 ~ 1000 sec.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.3.6.2 |
gratuitousArpIpAddress1The IP address of the static gratuitous ARP.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.3.6.3 |
gratuitousArpMacAddress1The MAC address of the static gratuitous ARP.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.3.6.4 |
gratuitousArpIpAddress2The IP address of the static gratuitous ARP.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.3.6.5 |
gratuitousArpMacAddress2The MAC address of the static gratuitous ARP.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.3.6.6 |
gratuitousArpIpAddress3The IP address of the static gratuitous ARP.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.3.6.7 |
gratuitousArpMacAddress3The MAC address of the static gratuitous ARP.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.3.6.8 |
gratuitousArpIpAddress4The IP address of the static gratuitous ARP.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.3.6.9 |
gratuitousArpMacAddress4The MAC address of the static gratuitous ARP.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.3.6.10 |
portSetting OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.4 |
opModeSetting OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.4.1 |
opMode OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.4.1.1 |
opModePortTableThe serial ports' operation mode table. SEQUENCE OF OpModePortEntry .1.3.6.1.4.1.8691.2.13.1.4.1.1.1 |
opModePortEntryThe serial port's operation mode entry. OpModePortEntry .1.3.6.1.4.1.8691.2.13.1.4.1.1.1.1 |
portIndexThe serial port index.ro INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.1.1.1.1 |
portModeThe operation mode of the serial port. Note that
changing this setting may also change the application.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.1.1.1.1.2 |
opModeParam OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.4.1.2 |
realCOM OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.4.1.2.1 |
realCOMTableThe Real COM mode table. SEQUENCE OF RealCOMEntry .1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1 |
realCOMEntryThe Real COM mode entry. RealCOMEntry .1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1 |
realCOMTcpAliveCheckThe TCP alive check time.
0 min: TCP connection will not be closed when the
TCP connection is idle.
1 to 99 min: The NPort W2x50A series device server
automatically closes the TCP connection if there is
no TCP activity for the given time. After the
connection is closed, the NPort W2x50A series device
server starts listening for another Real COM driver
Connection.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.1 |
realCOMMaxConnectionMax connection is usually used when the user needs
to receive data from different hosts simultaneously.
The factory default is 1. In this case, only one
specific host can access this port of the NPort
W2x50A series device server, and the Real COM driver
on that host will have full control over the port.
Max. connection = 1:
Allows only a single host's Real COM driver to open
the specific NPort W2x50A series device server's
serial port.
Max connection = 2 to 8:
Allows 2 to 8 hosts' Real COM drivers to open the
specific NPort W2x50A series device server's
serial port, at the same time. When multiple hosts'
Real COM drivers open the serial port at the same
time, the COM driver only provides a pure data tunnel
without control ability. The serial port parameter
will use the firmware settings instead of getting
the settings from your application program (AP).rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.2 |
realCOMIgnoreJammedIpPreviously, when Max connection was set to a value
greater than 1, and the serial device was
transmitting data, if any one of the connected hosts
stopped responding, the serial device would wait
until the data had been transmitted successfully
before transmitting the second group of data to all
hosts. Currently, if you select Yes for 'Ignore
jammed IP,' the host that is not responding will be
ignored, but the data will still be transmitted to
the other hosts.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.3 |
realCOMAllowDriverControlIf Max connection is greater than 1, NPort will
ignore driver control commands from all connected
hosts. However, if you set Allow driver control to
YES, control commands will be accepted. Note that
since the NPort W2x50A series device server may get
configuration changes from multiple hosts, the most
recent command received will take precedence.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.4 |
realCOMConnectionDownRTSFor some applications, serial devices must obtain
the Ethernet link status by reading the RTS signal from the
NPort W2x50A series device server. If this setting is
set to 'always low,' RTS will change its state to
low if the Ethernet link is off.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.5 |
realCOMConnectionDownDTRFor some applications, serial devices must obtain
the Ethernet link status by reading the DTR signal from the
NPort W2x50A series device server. If this setting is
set to 'always low,' DTR will change its state to
low if the Ethernet link is off.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.1.2.1.1.1.6 |
rfc2217 OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.4.1.2.2 |
rfc2217TableThe RFC2217 mode table. SEQUENCE OF Rfc2217Entry .1.3.6.1.4.1.8691.2.13.1.4.1.2.2.1 |
rfc2217EntryThe RFC2217 mode entry. Rfc2217Entry .1.3.6.1.4.1.8691.2.13.1.4.1.2.2.1.1 |
rfc2217TcpAliveCheckThe TCP alive check time.
0 min: TCP connection will not be closed when the
TCP connection is idle.
1 to 99 min: The NPort W2x50A series device server
automatically closes the TCP connection if there is
no TCP activity for the given time. After the
connection is closed, the NPort W2x50A series
device server starts listening for another TCP Connection.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.2.1.1.1 |
rfc2217TcpPortTCP server port of RFC2217.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.2.1.1.2 |
tcpServer OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.4.1.2.3 |
tcpServerTableThe TCP server mode table. SEQUENCE OF TcpServerEntry .1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1 |
tcpServerEntryThe TCP server mode entry. TcpServerEntry .1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1 |
tcpServerTcpAliveCheckThe TCP alive check time.
0 min: TCP connection will not be closed when the
TCP connection is idle.
1 to 99 min: The NPort W2x50A series device server
automatically closes the TCP connection if there is
no TCP activity for the given time. After the
connection is closed, the NPort W2x50A series device
server starts listening for another TCP Connection.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.1 |
tcpServerInactivityTime0 ms: TCP connection is not closed when the
serial line is idle.
1-65535 ms: The NPort W2x50A series device server
automatically closes the TCP connection if there is
no serial data activity for the given time. After
the connection is closed, the NPort W2x50A series
device server starts listening for another
TCP connection.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.2 |
tcpServerMaxConnectionMax connection is usually used when the user needs
to receive data from different hosts simultaneously.
The factory default is 1. In this case, only one
specific host can access this port of the NPort
W2x50A series device server, and the TCP server driver
on that host will have full control over the port.
Max. connection 1:
Allows only a single host's to connect specific
NPort W2x50A series device
Max connection 2 to 8:
Allows 2 to 8 hosts' to conncect NPort W2x50A series
device at the same time.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.3 |
tcpServerIgnoreJammedIpPreviously, when Max connection was set to a value
greater than 1, and the serial device was
transmitting data, if any one of the connected hosts
stopped responding, the serial device would wait
until the data had been transmitted successfully
before transmitting the second group of data to all
hosts. Currently, if you select Yes for 'Ignore
jammed IP,' the host that is not responding will be
ignored, but the data will still be transmitted to
the other hosts.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.4 |
tcpServerAllowDriverControlIf Max connection is greater than 1, NPort will
ignore driver control commands from all connected
hosts. However, if you set Allow driver control to
YES, control commands will be accepted. Note that
since the NPort W2x50A series device server may
get configuration changes from multiple hosts, the
most recent command received will take precedence.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.5 |
tcpServerTcpPortThe 'TCP port' is the TCP port that the NPort
W2x50A series device server uses to listen to
connections, and that other devices must use to
contact the NPort W2x50A series device server.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.6 |
tcpServerCmdPortThe 'Command port' is a TCP port used to listen for
SSDK commands from the host. In order to
prevent a TCP port conflict with other applications,
the user can set the Command port to another port
if needed.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.7 |
tcpServerConnectionDownRTSFor some applications, serial devices must obtain
the Ethernet link status from the RTS signal sent by the
NPort W2x50A series device server. If this setting is
set to 'goes low,' RTS will change the state to
low if the Ethernet link is off.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.8 |
tcpServerConnectionDownDTRFor some applications, serial devices must obtain
the Ethernet link status from the DTR signal sent by the
NPort W2x50A series device server. If this setting is
set to 'goes low,' DTR will change the state to
low if the Ethernet link is off.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.1.2.3.1.1.9 |
tcpClient OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.4.1.2.4 |
tcpClientTableThe TCP client mode table. SEQUENCE OF TcpClientEntry .1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1 |
tcpClientEntryThe TCP client mode entry. TcpClientEntry .1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1 |
tcpClientTcpAliveCheckThe TCP alive check time.
0 min: TCP connection will not be closed when the
TCP connection is idle.
1 to 99 min: The NPort W2x50A series device client
automatically closes the TCP connection if there is
no TCP activity for the given time.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.1 |
tcpClientInactivityTime0 ms: TCP connection is not closed when the
serial line is idle.
1-65535 ms: The NPort W2x50A series device client
automatically closes the TCP connection if there is
no serial data activity for the given time.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.2 |
tcpClientIgnoreJammedIpPreviously, when Max connection was set to a value
greater than 1, and the serial device was
transmitting data, if any one of the connected hosts
stopped responding, the serial device would wait
until the data had been transmitted successfully
before transmitting the second group of data to all
hosts. Currently, if you select Yes for 'Ignore
jammed IP,' the host that is not responding will be
ignored, but the data will still be transmitted to
the other hosts.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.3 |
tcpClientDestinationAddress1The NPort W2x50A series device server can connect
actively to a remote host that has this IP address.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.4 |
tcpClientDestinationPort1The NPort W2x50A series device server can connect
actively to a remote host that has this TCP port number.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.5 |
tcpClientDestinationAddress2The NPort W2x50A series device server can
connect actively to a remote host that has this IP
address.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.6 |
tcpClientDestinationPort2The NPort W2x50A series device server can
connect actively to a remote host that
has this TCP port number.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.7 |
tcpClientDestinationAddress3The NPort W2x50A series device server can
connect actively to a remote host that
has this IP address.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.8 |
tcpClientDestinationPort3The NPort W2x50A series device server can
connect actively to a remote host that
has this port number.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.9 |
tcpClientDestinationAddress4The NPort W2x50A series device server can
connect actively to a remote host that
has this IP address.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.10 |
tcpClientDestinationPort4The NPort W2x50A series device server can
connect actively to a remote host that
has this port number.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.11 |
tcpClientDesignatedLocalPort1The local TCP port used to connect actively to the
remote host.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.12 |
tcpClientDesignatedLocalPort2The local TCP port used to connect actively to the
remote host.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.13 |
tcpClientDesignatedLocalPort3The local TCP port used to connect actively to the
remote host.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.14 |
tcpClientDesignatedLocalPort4The local TCP port used to connect actively to the
remote host.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.15 |
tcpClientConnectionControlEvents that cause the TCP client to drop the
connection.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.1.2.4.1.1.16 |
udp OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.4.1.2.5 |
udpTableThe UDP mode table. SEQUENCE OF UdpEntry .1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1 |
udpEntryThe UDP mode entry. UdpEntry .1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1 |
udpDestinationAddress1BeginThe NPort W2x50A series device server can actively
send UDP packets to remote hosts whose IP addresses
are in the range between this parameter and
udpDestinationAddress1End.rw IpAddress .1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.1 |
udpDestinationAddress1EndThe NPort W2x50A series device server can actively
send UDP packets to remote hosts whose IP addresses
are in the range between udpDestinationAddress1Begin
and this parameter.rw IpAddress .1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.2 |
udpDestinationPort1The NPort W2x50A series device server can actively
send UDP packets to remote hosts that have this UDP port
number.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.3 |
udpDestinationAddress2BeginThe NPort W2x50A series device server can actively
send UDP packets to remote hosts whose IP addresses
are in the range between this parameter and
udpDestinationAddress2End.rw IpAddress .1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.4 |
udpDestinationAddress2EndThe NPort W2x50A series device server can actively
send UDP packets to the remote hosts whose IP addresses
are in the range between udpDestinationAddress2Begin
and this parameter.rw IpAddress .1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.5 |
udpDestinationPort2The NPort W2x50A series device server can actively
send UDP packets to the remote hosts that have this
UDP port number.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.6 |
udpDestinationAddress3BeginThe NPort W2x50A series device server can actively
send UDP packets to remote hosts whose IP addresses
are in the range between this parameter and
udpDestinationAddress3End.rw IpAddress .1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.7 |
udpDestinationAddress3EndThe NPort W2x50A series device server can actively
send UDP packets to remote hosts whose IP addresses
are in the range between udpDestinationAddress3Begin
and this parameter.rw IpAddress .1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.8 |
udpDestinationPort3The NPort W2x50A series device server can actively
send UDP packets to remote hosts that have this UDP
port number.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.9 |
udpDestinationAddress4BeginThe NPort W2x50A series device server can actively
send UDP packets to remote hosts whose IP addresses
are in the range between this parameter and
udpDestinationAddress4End.rw IpAddress .1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.10 |
udpDestinationAddress4EndThe NPort W2x50A series device server can actively
send UDP packets to remote hosts whose IP addresses
are in the range between udpDestinationAddress4Begin
and this parameter.rw IpAddress .1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.11 |
udpDestinationPort4The NPort W2x50A series device server can actively
send UDP packets to remote hosts that have this
UDP port number.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.12 |
udpLocalListenPortThe UDP port that the NPort W2x50A series device
server listens to and that other devices must use
to contact the NPort W2x50A series device server.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.5.1.1.13 |
pairConnectionMaster OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.4.1.2.6 |
pairConnectionMasterTableThe pair connection master mode table. SEQUENCE OF PairConnectionMasterEntry .1.3.6.1.4.1.8691.2.13.1.4.1.2.6.1 |
pairConnectionMasterEntryThe pair connection master mode entry. PairConnectionMasterEntry .1.3.6.1.4.1.8691.2.13.1.4.1.2.6.1.1 |
pairConnectionMasterTcpAliveCheckThe TCP alive check time.
0 min: TCP connection will not be closed when the
TCP connection is idle.
1 to 99 min: The NPort W2x50A series device server
automatically closes the TCP connection if there is
no TCP activity for the given time. After the
connection is closed, the NPort W2x50A series device
server starts connecting again.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.6.1.1.1 |
pairConnectionMasterDestnationAddressIP address of pair connection slave.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.4.1.2.6.1.1.2 |
pairConnectionMasterDestnationTcpPortTCP port of pair connection slave.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.6.1.1.3 |
pairConnectionSlave OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.4.1.2.7 |
pairConnectionSlaveTableThe pair connection slave mode table. SEQUENCE OF PairConnectionSlaveEntry .1.3.6.1.4.1.8691.2.13.1.4.1.2.7.1 |
pairConnectionSlaveEntryThe pair connection slave mode entry. PairConnectionSlaveEntry .1.3.6.1.4.1.8691.2.13.1.4.1.2.7.1.1 |
pairConnectionSlaveTcpAliveCheckThe TCP alive check time.
0 min: TCP connection will not be closed when the
TCP connection is idle.
1 to 99 min: The NPort W2x50A series device server
automatically closes the TCP connection if there is
no TCP activity for the given time. After the
connection is closed, the NPort W2x50A series
device server starts listening for another TCP Connection.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.7.1.1.1 |
pairConnectionSlaveLocalTcpPortTCP server port of pair connection slave.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.7.1.1.2 |
ethernetModem OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.4.1.2.8 |
ethernetModemTableThe ethernet modem mode table. SEQUENCE OF EthernetModemEntry .1.3.6.1.4.1.8691.2.13.1.4.1.2.8.1 |
ethernetModemEntryThe ethernet modem mode entry. EthernetModemEntry .1.3.6.1.4.1.8691.2.13.1.4.1.2.8.1.1 |
ethernetModemTcpAliveCheckThe TCP alive check time.
0 min: TCP connection will not be closed when the
TCP connection is idle.
1 to 99 min: The NPort W2x50A series device server
automatically closes the TCP connection if there is
no TCP activity for the given time.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.8.1.1.1 |
ethernetModemLocalTcpPortTCP server port of ethernet modem.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.8.1.1.2 |
reverseTerminal OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.4.1.2.9 |
reverseTerminalTableThe reverse terminal mode table. SEQUENCE OF ReverseTerminalEntry .1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1 |
reverseTerminalEntryThe reverse terminal mode entry. ReverseTerminalEntry .1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1 |
reverseTerminalTcpAliveCheckThe TCP alive check time.
0 min: TCP connection will not be closed when the
TCP connection is idle.
1 to 99 min: The NPort W2x50A series device server
automatically closes the TCP connection if there is
no TCP activity for the given time.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1.1 |
reverseTerminalInactivityTime0 min: TCP connection is not closed when the
serial line is idle.
0-99 min: The NPort W2x50A series device server
automatically closes the TCP connection if there is
no serial data activity for the given time. After
the connection is closed, the NPort W2x50P series
device server starts listening for another
TCP connection.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1.2 |
reverseTerminalTcpPortEach of the NPort W2x50A series device server's serial
ports are mapped to a TCP port.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1.3 |
reverseTerminalAuthenticationTypeThe reverse terminal authentication type.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1.4 |
reverseTerminalMapKeysIf data received through NPort W2x50A series device
server's Ethernet port is sent using the 'enter'
command, the data will be transmitted out through
the serial port with an added
1. 'carriage return + line feed' if you select the
'cr-lf' option (i.e., the cursor will jump to the
next line, and return to the first character of the
line)
2. 'carriage return' if you select the 'cr' option
(i.e., the cursor will return to the first character
of the line
3. 'line feed' if you select the 'lf' option. (i.e.,
the cursor will jump to the next line, but not move
horizontally)rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.1.2.9.1.1.5 |
dataPacking OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.4.1.3 |
dataPackingPortTableThe Data Packing table. SEQUENCE OF DataPackingPortEntry .1.3.6.1.4.1.8691.2.13.1.4.1.3.1 |
dataPackingPortEntryThe Data Packing entry. DataPackingPortEntry .1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1 |
portPacketLengthIf the value is 0, the Delimiter Process will be
used, regardless of the length of the data
packet. If the data length (in bytes) matches the
configured value, the data will be forced out. The
data length can be configured from 0 to 1024 bytes.
Set to 0 if you do not need to limit the length.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.1 |
portDelimiter1EnableEnable the first delimiter character.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.2 |
portDelimiter1The first delimiter character, in hex decimal.rw DisplayString .1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.3 |
portDelimiter2EnableEnable the second delimiter character.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.4 |
portDelimiter2The second delimiter character, in hex decimal.rw DisplayString .1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.5 |
portDelimiterProcess'delimiterAddOne' or 'delimiterAddTwo': The data
will be transmitted when an additional byte (for
'delimiterAddOne'), or an additional 2 bytes (for
'delimiterAddTwo') of data is received after
receiving the Delimiter.
'stripDelimiter': When the delimiter is received,
the Delimiter is deleted (i.e., stripped), and the
remaining data is transmitted.
'doNothing': The data will be transmitted when the
delimiter is received.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.6 |
portForceTransmit0: Disable the force transmit timeout.
1 to 65535: Forces the NPort W2x50A series device
server's TCP/IP protocol software to try to pack
serial data received during the specified time into
the same data frame.rw INTEGER .1.3.6.1.4.1.8691.2.13.1.4.1.3.1.1.7 |
comParamSetting OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.4.2 |
comParamPortTableThe Communication Parameters table. SEQUENCE OF ComParamPortEntry .1.3.6.1.4.1.8691.2.13.1.4.2.1 |
comParamPortEntryThe Communication Parameters entry. ComParamPortEntry .1.3.6.1.4.1.8691.2.13.1.4.2.1.1 |
portAliasPort alias is included to allow easy identification of
the serial devices that are connected to NPort W2x50A
series device server's serial port.rw DisplayString .1.3.6.1.4.1.8691.2.13.1.4.2.1.1.1 |
portInterfaceThe serial interface that the port works on.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.2.1.1.2 |
portBaudRateThe port's speed in bits per second. You can choose
a standard baud rate by indexing.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.2.1.1.3 |
portDataBitsThe number of bits in a character for the port.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.2.1.1.4 |
portStopBitsThe number of stop bits for the port.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.2.1.1.5 |
portParityThe parity bit for the port.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.2.1.1.6 |
portFlowControlThe flow-control method for the port.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.2.1.1.7 |
portFIFOEnable or disable the port's FIFO.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.2.1.1.8 |
dataBuffering OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.4.3 |
dataBufferingPortTableThe Data Buffering table. SEQUENCE OF DataBufferingPortEntry .1.3.6.1.4.1.8691.2.13.1.4.3.1 |
dataBufferingPortEntryThe Data Buffering entry. DataBufferingPortEntry .1.3.6.1.4.1.8691.2.13.1.4.3.1.1 |
portBufferingEnableEnable off-line port buffering.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.3.1.1.1 |
portSerialDataLoggingEnableEnable or disable serial data logging for the port.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.4.3.1.1.2 |
sysManagement OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.5 |
miscNetworkSettings OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.5.1 |
accessibleIp OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.5.1.1 |
enableAccessibleIpListEnable or disable the entire accessible IP list.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.1.1.1 |
accessibleIpListTableAccessible IP List table. SEQUENCE OF AccessibleIpListEntry .1.3.6.1.4.1.8691.2.13.1.5.1.1.2 |
accessibleIpListEntryAccessible IP List entry. AccessibleIpListEntry .1.3.6.1.4.1.8691.2.13.1.5.1.1.2.1 |
accessibleIpListIndexAccessible IP List index.ro INTEGER .1.3.6.1.4.1.8691.2.13.1.5.1.1.2.1.1 |
activeAccessibleIpListEnable or disable this accessible IP entry.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.1.1.2.1.2 |
accessibleIpListAddressAccessible IP address. This value can be the IP address of a
single host if the netmask is set to '255.255.255.255,'
or it can be a network address.rw IpAddress .1.3.6.1.4.1.8691.2.13.1.5.1.1.2.1.3 |
accessibleIpListNetmaskAccessible IP address netmask. The IP address and
netmask are used to specify a group of remote hosts.rw IpAddress .1.3.6.1.4.1.8691.2.13.1.5.1.1.2.1.4 |
snmpAgentSettings OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.5.1.2 |
snmpEnableEnable or disable SNMP agent.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.1.2.1 |
snmpContactNameThe SNMP contact information usually includes an
emergency contact name and telephone or pager
number.rw DisplayString .1.3.6.1.4.1.8691.2.13.1.5.1.2.2 |
snmpLocationSpecify the location string for SNMP agents, such as
the NPort W2x50A series device server. This string is
usually set to the street address where the NPort
W2x50A series device server is physically located.rw DisplayString .1.3.6.1.4.1.8691.2.13.1.5.1.2.3 |
authenticationServer OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.5.1.4 |
radiusServerIpThe IP address or domain name of the RADIUS server.rw DisplayString .1.3.6.1.4.1.8691.2.13.1.5.1.4.1 |
udpPortAuthenticationServerThe UDP port of the RADIUS server.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.1.4.3 |
radiusAccountingEnable or disable RADIUS accounting.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.1.4.4 |
sysLogSettings OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.5.1.5 |
sysLocalLogSystem cold start, System warm start.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.1.5.1 |
networkLocalLogDHCP/BOOTP get IP/renew, mail fail, NTP connect fail,
IP conflict, network link down.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.1.5.2 |
configLocalLogLogin fail, IP changed, password changed, firmware upgrade,
SSL certificate import, config export, wireless certificate import,
serial data log export.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.1.5.3 |
opModeLocalLogConnect, Disconnect, Restart.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.1.5.4 |
autoWarningSettings OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.5.2 |
eventSettings OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.5.2.1 |
mailWarningColdStartRefers to starting the system from power off
(contrast this with warm start). When performing a
cold start, the NPort W2x50A series device server
will automatically issue an auto warning message by
e-mail after booting up.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.2.1.1 |
mailWarningWarmStartRefers to restarting the NPort W2x50A without
turning the power off. When performing a warm start,
the NPort W2x50A series device server will
automatically send an e-mail after rebooting.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.2.1.2 |
mailWarningAuthFailureThe user inputs a wrong password from the Console
or Administrator. When authentication failure
occurs, the NPort W2x50A series device server
will immediately send an e-mail.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.2.1.3 |
mailWarningIpChangedThe user has changed the NPort W2x50A series
device server's IP address. When the IP address
changes,the NPort W2x50A series device server
will send an e-mail with the new IP address before
it reboots. If the NPort W2x50A series device
server is unable to send an e-mail message to the
mail server within 15 seconds, it will reboot anyway,
and abort the e-mail auto warning.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.2.1.4 |
mailWarningPasswordChangedThe user has changed the NPort W2x50A series device
server's password. When the password changes, the
NPort W2x50A series device server will send an e-mail
with the password changed notice before it reboots.
If the NPort W2x50A series device server is unable to
send an e-mail message to the mail server within 15
seconds, it will reboot anyway, and abort the e-mail
auto warning.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.2.1.5 |
trapServerColdStartRefers to starting the system from power off
(contrast this with warm start). When performing a
cold start, the NPort W2x50A series device server
will automatically issue an auto warning message by
sending an SNMP trap after booting up.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.2.1.6 |
trapServerWarmStartRefers to restarting the NPort W2x50A without
turning the power off. When performing a warm start,
the NPort W2x50A series device server will
automatically send an SNMP trap after rebooting.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.2.1.7 |
trapServerAuthFailureThe user inputs a wrong password from the Console
or Administrator. When authentication failure
occurs, the NPort W2x50A series device server will
immediately send an SNMP trap.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.2.1.8 |
serialEventSettings OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.5.2.2 |
portEventSettingsTablePort Event Settings Table. SEQUENCE OF PortEventSettingsEntry .1.3.6.1.4.1.8691.2.13.1.5.2.2.1 |
portEventSettingsEntryPort Event Settings entry. PortEventSettingsEntry .1.3.6.1.4.1.8691.2.13.1.5.2.2.1.1 |
mailDCDchangeA change in the DCD (Data Carrier Detect) signal
indicates that the modem connection status has
changed. For example, if the DCD signal changes to
low, it indicates that the connection line is down.
When the DCD signal changes to low, the NPort
W2x50A series device server will immediately send
an e-mail message.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.2.2.1.1.1 |
trapDCDchangeA change in the DCD (Data Carrier Detect) signal
indicates that the modem connection status has
changed. For example, if the DCD signal changes to
low, it indicates that the connection line is down.
When the DCD signal changes to low, the NPort
W2x50A series device server will immediately send
an SNMP trap.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.2.2.1.1.2 |
mailDSRchangeA change in the DSR (Data Set Ready) signal
indicates that the data communication equipment is
powered off. For example, if the DSR signal changes
to low, it indicates that the data communication
equipment is powered down. When the DSR signal
changes to low, the NPort W2x50A series device
server will immediately send an e-mail message.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.2.2.1.1.3 |
trapDSRchangeA change in the DSR (Data Set Ready) signal
indicates that the data communication equipment is
powered off. For example, if the DSR signal changes
to low, it indicates that the data communication
equipment is powered down. When the DSR signal
changes to low, the NPort W2x50A series device
server will immediately send an SNMP trap.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.2.2.1.1.4 |
emailAlert OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.5.2.3 |
emailWarningMailServerThe e-mail server's IP address or domain name of
the e-mail warning function.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.5.2.3.1 |
emailRequiresAuthenticationSet if the mail server requires user login.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.2.3.2 |
emailWarningUserNameThe user name used to log into the mail server if
authentication is required.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.5.2.3.3 |
emailWarningFromEmailThe e-mail address to be filled in the 'From' field of
the auto-warning e-mail.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.5.2.3.5 |
emailWarningFirstEmailAddrThe first email address to where the auto-warning
e-mail is to be sent.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.5.2.3.6 |
emailWarningSecondEmailAddrThe second email address to where the auto-warning
e-mail is to be sent.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.5.2.3.7 |
emailWarningThirdEmailAddrThe third email address to where the auto-warning
e-mail is to be sent.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.5.2.3.8 |
emailWarningFourthEmailAddrThe fourth email address to where the auto-warning
e-mail is to be sent.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.5.2.3.9 |
snmpTrap OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.5.2.4 |
snmpTrapReceiverIpSNMP trap server IP address or domain name.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.5.2.4.1 |
trapVersionSNMP trap version used for the auto-warning function.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.2.4.2 |
maintenance OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.5.3 |
consoleSettings OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.5.3.1 |
httpConsoleEnable or disable HTTP console.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.3.1.1 |
httpsConsoleEnable or disable HTTPS console.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.3.1.2 |
telnetConsoleEnable or disable Telnet console.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.3.1.3 |
sshConsoleEnable or disable SSH console.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.3.1.4 |
serialConsoleEnable or disable Serial console.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.3.1.5 |
resetButtonReset button setting.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.3.1.6 |
loadFactoryDefault OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.5.3.2 |
loadFactoryDefaultSettingThis function will reset all of the NPort W2x50A
series device server's settings to the factory default
values. Be aware that previous settings will be
lost. Selecting Reset to factory default
(excluding IP configuration) will reset all settings
except the IP configuration to factory defaults.
Selecting Reset to factory default will reset all
settings including the IP configuration to factory
defaults.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.5.3.2.1 |
sysStatus OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.6 |
s2eConnections OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.6.1 |
monitorRemoteIpTableSerial to Network Connections Remote IP table. SEQUENCE OF MonitorRemoteIpEntry .1.3.6.1.4.1.8691.2.13.1.6.1.1 |
monitorRemoteIpEntrySerial to Network Connections Remote IP entry. MonitorRemoteIpEntry .1.3.6.1.4.1.8691.2.13.1.6.1.1.1 |
remoteIpIndexSerial to Network Connections Remote IP index.ro INTEGER .1.3.6.1.4.1.8691.2.13.1.6.1.1.1.1 |
monitorRemoteIpThe remote IP currently connecting to this port.ro IpAddress .1.3.6.1.4.1.8691.2.13.1.6.1.1.1.2 |
serialPortStatus OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.6.2 |
monitorSerialPortStatusTableSerial Port Status table. SEQUENCE OF MonitorSerialPortStatusEntry .1.3.6.1.4.1.8691.2.13.1.6.2.1 |
monitorSerialPortStatusEntrySerial Port Status entry. MonitorSerialPortStatusEntry .1.3.6.1.4.1.8691.2.13.1.6.2.1.1 |
monitorTxCountView the number of bytes transmitted from the port
since the last time the port was initialized.ro INTEGER .1.3.6.1.4.1.8691.2.13.1.6.2.1.1.1 |
monitorRxCountView the number of bytes received by the port since
the last time the port was initialized.ro INTEGER .1.3.6.1.4.1.8691.2.13.1.6.2.1.1.2 |
monitorTxTotalCountView the number of bytes transmitted from the port
since the last time the system was initialized.ro INTEGER .1.3.6.1.4.1.8691.2.13.1.6.2.1.1.3 |
monitorRxTotalCountView the number of bytes received by the port since
the last time the system was initialized.ro INTEGER .1.3.6.1.4.1.8691.2.13.1.6.2.1.1.4 |
monitorDSRView the current DSR status of this port.ro Enumeration .1.3.6.1.4.1.8691.2.13.1.6.2.1.1.5 |
monitorDTRView the current DTR status of this port.ro Enumeration .1.3.6.1.4.1.8691.2.13.1.6.2.1.1.6 |
monitorRTSView the current RTS status of this port.ro Enumeration .1.3.6.1.4.1.8691.2.13.1.6.2.1.1.7 |
monitorCTSView the current CTS status of this port.ro Enumeration .1.3.6.1.4.1.8691.2.13.1.6.2.1.1.8 |
monitorDCDView the current DCD status of this port.ro Enumeration .1.3.6.1.4.1.8691.2.13.1.6.2.1.1.9 |
serialPortErrorCount OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.6.3 |
monitorSerialPortErrorCountTableSerial Port Error Count table. SEQUENCE OF MonitorSerialPortErrorCountEntry .1.3.6.1.4.1.8691.2.13.1.6.3.1 |
monitorSerialPortErrorCountEntrySerial Port Error Count entry. MonitorSerialPortErrorCountEntry .1.3.6.1.4.1.8691.2.13.1.6.3.1.1 |
monitorErrorCountFrameView the number of 'Frame' errors for this port.ro INTEGER .1.3.6.1.4.1.8691.2.13.1.6.3.1.1.1 |
monitorErrorCountParityView the number of 'Parity' errors for this port.ro INTEGER .1.3.6.1.4.1.8691.2.13.1.6.3.1.1.2 |
monitorErrorCountOverrunView the number of 'Overrun' errors for this port.ro INTEGER .1.3.6.1.4.1.8691.2.13.1.6.3.1.1.3 |
monitorErrorCountBreakView the number of 'Break' errors for this port.ro INTEGER .1.3.6.1.4.1.8691.2.13.1.6.3.1.1.4 |
serialPortSettings OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.6.4 |
monitorSerialPortSettingsTableSerial Port Settings table. SEQUENCE OF MonitorSerialPortSettingsEntry .1.3.6.1.4.1.8691.2.13.1.6.4.1 |
monitorSerialPortSettingsEntrySerial Port Settings entry. MonitorSerialPortSettingsEntry .1.3.6.1.4.1.8691.2.13.1.6.4.1.1 |
monitorBaudRateView the current baudrate of the port.ro INTEGER .1.3.6.1.4.1.8691.2.13.1.6.4.1.1.1 |
monitorDataBitsView the number of bits per byte for the port.ro Enumeration .1.3.6.1.4.1.8691.2.13.1.6.4.1.1.2 |
monitorStopBitsView the number of stop bits for the port.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.6.4.1.1.3 |
monitorParityView the parity bit for the port.ro Enumeration .1.3.6.1.4.1.8691.2.13.1.6.4.1.1.4 |
monitorRTSCTSFlowControlView if the port is using RTS/CTS flow control.ro Enumeration .1.3.6.1.4.1.8691.2.13.1.6.4.1.1.5 |
monitorXONXOFFFlowControlView if the port is using XON/XOFF flow control.ro Enumeration .1.3.6.1.4.1.8691.2.13.1.6.4.1.1.6 |
monitorFIFOView FIFO status of this port.ro Enumeration .1.3.6.1.4.1.8691.2.13.1.6.4.1.1.7 |
monitorInterfaceView the serial interface that the port is using.ro Enumeration .1.3.6.1.4.1.8691.2.13.1.6.4.1.1.8 |
serialPortBuffering OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.6.5 |
monitorSerialPortBufferingTableSerial Port Buffering table. SEQUENCE OF MonitorSerialPortBufferingEntry .1.3.6.1.4.1.8691.2.13.1.6.5.1 |
monitorSerialPortBufferingEntrySerial Port Settings entry. MonitorSerialPortBufferingEntry .1.3.6.1.4.1.8691.2.13.1.6.5.1.1 |
monitorBufferingView length of buffered data for the port. The length unit is byte.ro INTEGER .1.3.6.1.4.1.8691.2.13.1.6.5.1.1.1 |
sysWlanStatus OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.6.6 |
wlanStatusActiveProfileNameThe active profile name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.6.6.1 |
wlanStatusIpConfigurationThe IP configuration mode of the NPort. You can
choose from four possible IP configuration modes:
Static, DHCP, DHCP/BOOTP, BOOTP.ro Enumeration .1.3.6.1.4.1.8691.2.13.1.6.6.2 |
wlanStatusIpAddressAn IP address is a number assigned to a network
device (such as a computer) as a permanent address
on the network. Computers use the IP address to
identify and talk to each other over the network.
Choose a proper IP address that is unique and valid
in your network environment.ro IpAddress .1.3.6.1.4.1.8691.2.13.1.6.6.3 |
wlanStatusNetMaskA subnet mask represents all of the network hosts
at one geographic location, in one building, or on
the same local area network. When a packet is sent
out over the network, the NPort W2x50A series
device server will use the subnet mask to check
whether the TCP/IP host specified in the packet is on
the local network segment. If the address is on the
same network segment as the NPort W2x50A series
device server, a connection is established directly
from the NPort W2x50A series device server.
Otherwise, the connection is established through the
given default gateway.ro IpAddress .1.3.6.1.4.1.8691.2.13.1.6.6.4 |
wlanStatusDefaultGatewayA gateway is a network computer that acts as an
entrance to another network. Usually, the computers
that control traffic within the network or at the
local Internet service provider are gateway nodes.
The NPort W2x50A series device server needs to
know the IP address of the default gateway computer
in order to communicate with the hosts outside the
local network environment. For correct gateway IP
address information, consult with the network
administrator.ro IpAddress .1.3.6.1.4.1.8691.2.13.1.6.6.5 |
wlanStatusNetworkTypeNetwork Type of Wireless LAN. The possible values are
'Infrastrcture Mode' and 'Ad-hoc Mode'ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.6.6.6 |
wlanStatusRFTypeRF type of Wireless LAN. The possible values are
'N/A', 'Auto', '802.11a', '802.11b', '802.11g'ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.6.6.7 |
wlanStatusSSIDThe SSID of WLAN.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.6.6.8 |
wlanStatusChannelThe currently used channel.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.6.6.9 |
wlanStatusAuthenticationAuthentication type of Wireless LAN. The possible values are
'Unknown', 'Open System', 'Shared Key', 'WPA', 'WPA-PSK', 'WPA2', 'WPA2-PSK'ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.6.6.10 |
wlanStatusEncryptionShow encryption type of Wireless LAN.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.6.6.11 |
wlanStatusRegionDisplay region. The possible values are 'US', 'EU', 'JP'ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.6.6.12 |
wlanStatusSignalStrengthThe signal strength of Wireless LAN.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.6.6.13 |
wlanStatusConnectionSpeedThe connection speed of Wireless LAN.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.6.6.14 |
wlanStatusCurrentBSSIDThe current BSSID of Wireless LAN.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.8691.2.13.1.6.6.15 |
activateSettings OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.7 |
doActivateActivate current settings.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.7.1 |
restart OBJECT IDENTIFIER .1.3.6.1.4.1.8691.2.13.1.8 |
restartPortsRestart serial port. Restarting will cause port
reseting.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.8.1 |
restartSystemRestart the NPort W2x50A series device server.
Be sure to save all of your configuration changes
before you restart the system. Otherwise, all of
the changes will be lost.rw Enumeration .1.3.6.1.4.1.8691.2.13.1.8.2 |