Home/Catalog/MOXA-NP6000-MIB

MOXA-NP6000-MIB

AI MIB Summary

The MOXA-NP6000-MIB enables SNMP-based monitoring and management of Moxa NPort 6000 serial-to-Ethernet devices, specifically tracking port operational status, serial line statistics (such as error counts and throughput), and hardware health indicators like temperature and power supply states.

The MIB module for Moxa NPort 6000 series specific information.
Main OID:
np6000.1.3.6.1.4.1.8691.2.8
356
Objects
Active
Status
2
Dependencies

Imported Objects

SNMPv2-SMI
SNMPv2-TC

Objects

356 total
Object Name
moxa
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691
nport
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2
np6000The MIB module for Moxa NPort 6000 series specific information.
MODULE-IDENTITY
.1.3.6.1.4.1.8691.2.8
swMgmt
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1
overview
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.1
modelNameThe model name of the NPort. The possible values of this parameter are: 'NP6150' for NPort 6150, 'NP6250' for NPort 6250, 'NP6250-S-SC' for NPort 6250-S-SC, 'NP6250-M-SC' for NPort NPort 6250-M-SC, 'NP6450' for NPort 6450, 'NP6650-8' for NPort 6650-8, and 'NP6650-16' for NPort 6650-16.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.1.1
serialNumberThe serial number of the NPort. Every NPort 6000 series device server is assigned a unique serial number before it is shipped.ro
INTEGER
.1.3.6.1.4.1.8691.2.8.1.1.2
firmwareVersionThe version of the firmware currently running on the NPort.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.1.3
macAddressThe MAC address of the NPort's Ethernet interface.ro
MacAddress (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.1.4
viewLanSpeedThe current speed and link status of the NPort's built-in LAN port. The possible values are 'No link', '10M/Link,' or '100M/Link.'ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.1.5
viewLanModuleSpeedThe current speed and link status of the the network module's LAN ports, if the module is installed. The value includes two parts. Each part indicates the status of one of the LAN ports. The possible values are 'No link', '10M/Link,' '100M/Link,' or continunous dashes to indicate that the LAN module is not installed.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.1.6
upTimeThe time (in human-readable notation) since the system was was last re-initialized.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.1.7
moduleTypeThe module name currently plugged into the NPort.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.1.8
basicSetting
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.2
serverSetting
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.2.1
serverNameA text string used to identify the NPort.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.2.1.1
serverLocationA text string used to identify the location of the NPort. This option is useful for specifying the location or application of different NPort device servers.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.2.1.2
timeSetting
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.2.2
timeZoneThe time-zone index of the NPort.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.2.2.1
localTimeThe system time in seconds since 1970/1/1.rw
DateAndTime (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.2.2.2
timeServerThe NPort 6000 series device server uses SNTP (RFC-1769) for auto time calibration. Input the correct 'Time server' IP address or domain name. Once the NPort 6000 series device server is configured with the correct Time server address, it will request time information from the Time server every 10 minutes.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.2.2.3
networkSetting
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.3
ipConfigurationThe IP configuration mode of the NPort. You can choose from four possible IP configuration modes: Static, DHCP, DHCP/BOOTP, BOOTP, and PPPoE.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.3.1
sysIpAddressAn IP address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP address to identify and talk to each other over the network. Choose a proper IP address that is unique and valid in your network environment.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.3.2
netMaskA subnet mask represents all of the network hosts at one geographic location, in one building, or on the same local area network. When a packet is sent out over the network, the NPort 6000 series device server will use the subnet mask to check whether the TCP/IP host specified in the packet is on the local network segment. If the address is on the same network segment as the NPort 6000 series device server, a connection is established directly from the NPort 6000 series device server. Otherwise, the connection is established through the given default gateway.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.3.3
defaultGatewayA gateway is a network computer that acts as an entrance to another network. Usually, the computers that control traffic within the network or at the local Internet service provider are gateway nodes. The NPort 6000 series device server needs to know the IP address of the default gateway computer in order to communicate with the hosts outside the local network environment. For correct gateway IP address information, consult with the network administrator.ro
IpAddress
.1.3.6.1.4.1.8691.2.8.1.3.4
dnsServer1IpAddrThe first DNS server address. When the user wants to visit a particular website, the computer asks a Domain Name System (DNS) server for the websites correct IP address, and then the computer uses the response to connect to the web server. DNS is the way that Internet domain names are identified and translated into IP addresses. A domain name is an alphanumeric name, such as moxa.com, that it is usually easier to remember. A DNS server is a host that translates this kind of text-based domain name into the numeric IP address used to establish a TCP/IP connection.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.3.5
dnsServer2IpAddrThe second DNS server address. When the user wants to visit a particular website, the computer asks a Domain Name System (DNS) server for the websites correct IP address, and then the computer uses the response to connect to the web server. DNS is the way that Internet domain names are identified and translated into IP addresses. A domain name is an alphanumeric name, such as moxa.com, that it is usually easier to remember. A DNS server is a host that translates this kind of text-based domain name into the numeric IP address used to establish a TCP/IP connection.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.3.6
pppoeUserAccountThe user account used by the NPort to access the Internet using PPPoE. For dynamic broad band networks such as xDSL or Cable Modem, users must enter the username and password that they received from their ISP to establish a network connection.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.3.7
pppoePasswordThe password used by the NPort to access the Internet using PPPoE. For dynamic broad band networks such as xDSL or Cable Modem, users must enter the username and password that they received from their ISP to establish a network connection.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.3.8
winsFunctionEnable or disable the WINS server.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.3.9
winsServerIf a WINS Server is connected to the network, use this field to record the WINS Servers IP address. TCP/IP uses IP addresses to identify hosts, but users often use symbolic names, such as computer names. The WINS Server, which uses NetBIOS over TCP/IP, contains a dynamic database to map computer names to IP addresses.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.3.10
lan1SpeedIEEE802.3 Ethernet supports the auto negotiation speed function to get suitable speeds. However, for connecting to some switches/hubs, the communication speed must be fixed at 100 Mbps or 10 Mbps. Users can use this function to fix the communication speed.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.3.11
routingProtocolThe routing protocol used by the NPort. This value could be none, RIP-1, or RIP-2.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.3.12
gratuitousArpEnable or disable the gratuitous ARP function. For some applications, users need the NPort 6000 series device server to send broadcast packets to update the ARP table on the server. If the customer enables this function and sets the send period, the NPort 6000 series device server will send broadcast packets periodically.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.3.13
gratuitousArpSendPeriodThe send period of the gratuitous ARP function.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.3.14
portSetting
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.4
opModeSetting
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.4.1
opMode
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.4.1.1
opModePortTableThe serial ports' operation mode table.
SEQUENCE OF OpModePortEntry
.1.3.6.1.4.1.8691.2.8.1.4.1.1.1
opModePortEntryThe serial port's operation mode entry.
OpModePortEntry
.1.3.6.1.4.1.8691.2.8.1.4.1.1.1.1
portIndexThe serial port index.ro
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.1.1.1.1
portApplicationThe application of the serial port. Note that changing this setting may also change the operation mode.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.1.1.1.2
portModeThe operation mode of the serial port. Note that changing this setting may also change the application.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.1.1.1.3
application
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.4.1.2
deviceControl
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.1
deviceControlTableThe Device Control application table.
SEQUENCE OF DeviceControlEntry
.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1
deviceControlEntryThe Device Control application entry.
DeviceControlEntry
.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1
deviceControlTcpAliveCheckThe TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.1
deviceControlMaxConnectionMax connection is usually used when the user needs to receive data from different hosts simultaneously. The factory default is 1. In this case, only one specific host can access this port of the NPort 6000 series device server, and the Real COM driver on that host will have full control over the port. Max. connection = 1: Allows only a single hosts Real COM driver to open the specific NPort 6000 series device servers serial port. Max connection = 2 to 8: Allows 2 to 8 hosts Real COM drivers to open the specific NPort 6000 series device servers serial port, at the same time. When multiple hosts Real COM drivers open the serial port at the same time, the COM driver only provides a pure data tunnel without control ability. The serial port parameter will use the firmware settings instead of getting the settings from your application program (AP).rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.2
deviceControlIgnoreJammedIpPreviously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped responding, the serial device would wait until the data had been transmitted successfully before transmitting the second group of data to all hosts. Currently, if you select Yes for 'Ignore jammed IP,' the host that is not responding will be ignored, but the data will still be transmitted to the other hosts.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.3
deviceControlAllowDriverControlIf Max connection is greater than 1, NPort will ignore driver control commands from all connected hosts. However, if you set Allow driver control to YES, control commands will be accepted. Note that since the NPort 6000 series device server may get configuration changes from multiple hosts, the most recent command received will take precedence.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.4
deviceControlSecureIf 'Secure' is enabled, the data on the Ethernet will be encrypted with SSL.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.5
deviceControlTcpPortThe 'TCP port' is the TCP port that the NPort 6000 series device server uses to listen to connections, and that other devices must use to contact the NPort 6000 series device server.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.6
deviceControlConnectionDownRTSFor some applications, serial devices must obtain the Ethernet link status by reading the RTS signal from the NPort 6000 series device server. If this setting is set to 'goes low,' RTS will change its state to low if the Ethernet link is off.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.7
deviceControlConnectionDownDTRFor some applications, serial devices must obtain the Ethernet link status by reading the DTR signal from the NPort 6000 series device server. If this setting is set to 'goes low,' DTR will change its state to low if the Ethernet link is off.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.8
socket
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2
socketTableThe Socket application table.
SEQUENCE OF SocketEntry
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1
socketEntryThe Socket application entry.
SocketEntry
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1
socketTcpAliveCheckThe TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.1
socketInactivityTime0 ms: TCP connection is not closed when the serial line is idle. 1-65535 ms: The NPort 6000 series device server automatically closes the TCP connection if there is no serial data activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another TCP connection.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.2
socketMaxConnectionMax connection is usually used when the user needs to receive data from different hosts simultaneously. The factory default is 1. In this case, only one specific host can access this port of the NPort 6000 series device server, and the Real COM driver on that host will have full control over the port. Max. connection 1: Allows only a single hosts Real COM driver to open the specific NPort 6000 series device servers serial port. Max connection 2 to 8: Allows 2 to 8 hosts Real COM drivers to open the specific NPort 6000 series device servers serial port, at the same time. When multiple hosts Real COM drivers open the serial port at the same time, the COM driver only provides a pure data tunnel without control ability. The serial port parameter will use the firmware settings instead of depending on your application program (AP).rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.3
socketIgnoreJammedIpPreviously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped responding, the serial device would wait until the data had been transmitted successfully before transmitting the second group of data to all hosts. Currently, if you select Yes for 'Ignore jammed IP,' the host that is not responding will be ignored, but the data will still be transmitted to the other hosts.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.4
socketAllowDriverControlIf Max connection is greater than 1, NPort will ignore driver control commands from all connected hosts. However, if you set Allow driver control to YES, control commands will be accepted. Note that since the NPort 6000 series device server may get configuration changes from multiple hosts, the most recent command received will take precedence.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.5
socketSecureIf Secure is enabled, data sent over the Ethernet will be encrypted with SSL.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.6
socketTcpPortThe 'TCP port' is the TCP port that the NPort 6000 series device server uses to listen to connections, and that other devices must use to contact the NPort 6000 series device server.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.7
socketCmdPortThe 'Command port' is a TCP port used to listen for IP-Serial Lib commands from the host. In order to prevent a TCP port conflict with other applications, the user can set the Command port to another port if needed. IP-Serial Lib will automatically check the Command Port on the NPort 6000 series device server to avoid the need for the user to configure the program.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.8
socketTcpServerConnectionDownRTSFor some applications, serial devices must obtain the Ethernet link status from the RTS signal sent by the NPort 6000 series device server. If this setting is set to 'goes low,' RTS will change the state to low if the Ethernet link is off.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.9
socketTcpServerConnectionDownDTRFor some applications, serial devices must obtain the Ethernet link status from the DTR signal sent by the NPort 6000 series device server. If this setting is set to 'goes low,' DTR will change the state to low if the Ethernet link is off.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.10
socketTcpClientDestinationAddress1The NPort 6000 series device server can connect actively to a remote host that has this IP address.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.11
socketTcpClientDestinationPort1The NPort 6000 series device server can connect actively to a remote host that has this TCP port number.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.12
socketTcpClientDestinationAddress2The NPort 6000 series device server can connect actively to a remote host that has this IP address.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.13
socketTcpClientDestinationPort2The NPort 6000 series device server can connect actively to a remote host that has this TCP port number.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.14
socketTcpClientDestinationAddress3The NPort 6000 series device server can connect actively to a remote host that has this IP address.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.15
socketTcpClientDestinationPort3The NPort 6000 series device server can connect actively to a remote host that has this port number.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.16
socketTcpClientDestinationAddress4The NPort 6000 series device server can connect actively to a remote host that has this IP address.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.17
socketTcpClientDestinationPort4The NPort 6000 series device server can connect actively to a remote host that has this port number.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.18
socketTcpClientDesignatedLocalPort1The local TCP port used to connect actively to the remote host.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.19
socketTcpClientDesignatedLocalPort2The local TCP port used to connect actively to the remote host.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.20
socketTcpClientDesignatedLocalPort3The local TCP port used to connect actively to the remote host.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.21
socketTcpClientDesignatedLocalPort4The local TCP port used to connect actively to the remote host.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.22
socketTcpClientConnectionControlEvents that cause the TCP client to drop the connection.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.23
socketUdpDestinationAddress1BeginThe NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and socketUdpDestinationAddress1End.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.24
socketUdpDestinationAddress1EndThe NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between socketUdpDestinationAddress1Begin and this parameter.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.25
socketUdpDestinationPort1The NPort 6000 series device server can actively send UDP packets to remote hosts that have this port number.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.26
socketUdpDestinationAddress2BeginThe NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and socketUdpDestinationAddress2End.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.27
socketUdpDestinationAddress2EndThe NPort 6000 series device server can actively send UDP packets to the remote hosts whose IP addresses are in the range between socketUdpDestinationAddress2Begin and this parameter.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.28
socketUdpDestinationPort2The NPort 6000 series device server can actively send UDP packets to the remote hosts that have this TCP port number.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.29
socketUdpDestinationAddress3BeginThe NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and socketUdpDestinationAddress3End.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.30
socketUdpDestinationAddress3EndThe NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between socketUdpDestinationAddress3Begin and this parameter.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.31
socketUdpDestinationPort3The NPort 6000 series device server can actively send UDP packets to remote hosts that have this TCP port number.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.32
socketUdpDestinationAddress4BeginThe NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and socketUdpDestinationAddress4End.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.33
socketUdpDestinationAddress4EndThe NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between socketUdpDestinationAddress4Begin and this parameter.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.34
socketUdpDestinationPort4The NPort 6000 series device server can actively send UDP packets to remote hosts that have this TCP port number.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.35
socketUdpLocalListenPortThe UDP port that the NPort 6000 series device server listens to and that other devices must use to contact the NPort 6000 series device server.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.36
pairConnection
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.3
pairConnectionTableThe Pair Connection table.
SEQUENCE OF PairConnectionEntry
.1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1
pairConnectionEntryThe Pair Connection entry.
PairConnectionEntry
.1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1
pairConnectionTcpAliveCheckThe TCP alive check time. 0 min: TCP connection will not be closed if the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.1
pairConnectionSecureIf Secure is enabled, the Ethernet data will be encrypted using SSL.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.2
pairConnectionDestinationAddressThe Pair Connection 'Master' will contact the network host that has the specified IP address.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.3
pairConnectionDestinationPortData will be transmitted through the specified port number. Note that you must configure the same TCP port number for the device server acting as the Pair Connection 'Slave.'rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.4
pairConnectionTcpPortThis port number must be the same port number that was set up for the Pair Connection 'Master' device server.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.5
ethernetModem
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.4
ethernetModemTableThe Ethernet Modem table.
SEQUENCE OF EthernetModemEntry
.1.3.6.1.4.1.8691.2.8.1.4.1.2.4.1
ethernetModemEntryThe Ethernet Modem entry.
EthernetModemEntry
.1.3.6.1.4.1.8691.2.8.1.4.1.2.4.1.1
ethernetModemTcpAliveCheckThe TCP alive check time. 0 min: TCP connection will not be closed if the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.4.1.1.1
ethernetModemTcpPortThe local TCP port used to listen for incoming calls from a remote ethernet modem.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.4.1.1.2
terminal
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5
terminalTableThe Terminal Application table.
SEQUENCE OF TerminalEntry
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1
terminalEntryThe Terminal Application entry.
TerminalEntry
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1
terminalTcpAliveCheckThe TCP alive check time. 0 min: TCP connection will not be closed if the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection from another host.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.1
terminalInactivityTime0 min: TCP connection will not be closed if the serial line becomes idle. 0-99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no serial data activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another host's TCP connection.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.2
terminalAutoLinkProtocolIf Auto-Link protocol is set to 'None,' the NPort 6000 series device server will not connect to the host automatically. If Auto-Link protocol is set to 'Telnet,' the NPort 6000 series device server will connect to the host automatically using Telnet. If Auto-Link protocol is set to 'Rlogin,' the NPort 6000 series device server will connect to the host automatically using rlogin.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.3
terminalPrimaryHostAddressIf specified, designates a 'permanent' host to which the terminal will always be connected.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.4
terminalSecondHostAddressIf specified, designates a 'permanent' host to which the terminal will always be connected.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.5
terminalTelnetTcpPortBy default, the Telnet TCP port number is set to 23, which is the default TCP port number for Telnet. If you need to telnet to this NPort 6000 series device server's serial port, set the Telnet TCP port to a different number.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.6
terminalSshTcpPortBy default, the SSH TCP port number is set to 22, which is the default TCP port number for SSH. If you need to use SSH to connect to this NPort 6000 series device server's serial port, set the Telnet TCP port to a different number.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.7
terminalTypeDefines the terminal type for outgoing connections.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.8
terminalMaxSessionsConfigure the max. number of sessions.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.9
terminalChangeSessionDefines the control character used to change the terminal session.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.10
terminalQuitDefines the control character used to quit a terminal session.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.11
terminalBreakDefines the control character used to send a Telnet BREAK message.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.12
terminalInterruptDefines the control character used to send a Telnet INTERRUPT message.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.13
terminalAuthenticationTypeThe terminal authentication type.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.14
terminalAutoLoginPromptThe prompt string for the automatic login ID. When the NPort 6000 series device server receives this string from a remote telnet/rlogin server, it will automatically reply with the user ID.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.15
terminalPasswordPromptThe prompt string for the automatic login password. When the NPort 6000 series device server receives this string from a remote telnet/rlogin server, it will automatically reply with the user password.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.16
terminalLoginUserNameTerminal login ID for automatic login.rw
DisplayString
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.17
terminalLoginPasswordTerminal login password for automatic login.rw
DisplayString
.1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.18
reverseTerminal
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.6
reverseTerminalTableThe Reverse Terminal Application table.
SEQUENCE OF ReverseTerminalEntry
.1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1
reverseTerminalEntryThe Reverse Terminal Application entry.
ReverseTerminalEntry
.1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1
reverseTerminalTcpAliveCheckThe TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.1
reverseTerminalInactivityTime0 min: TCP connection will not be closed if the serial line becomes idle. 0-99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no serial data activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another TCP connection.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.2
reverseTerminalTcpPortEach of the NPort 6000 series device server's serial ports are mapped to a TCP port.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.3
reverseTerminalAuthenticationTypeThe reverse terminal authentication type.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.4
reverseTerminalMapKeysIf data received through NPort 6000 series device server's Ethernet port is sent using the 'enter' command, the data will be transmitted out through the serial port with an added 1. 'carriage return + line feed' if you select the 'cr-lf' option (i.e., the cursor will jump to the next line, and return to the first character of the line) 2. 'carriage return' if you select the 'cr' option (i.e., the cursor will return to the first character of the line 3. 'line feed' if you select the 'lf' option. (i.e., the cursor will jump to the next line, but not move horizontally)rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.5
printer
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.7
printerTableThe Printer Application table.
SEQUENCE OF PrinterEntry
.1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1
printerEntryThe Printer Application entry.
PrinterEntry
.1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1
printerTcpAliveCheckThe TCP alive check time. 0 min: TCP connection will not be closed if the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.1
printerTcpPortThe host uses this value to determine the Group to which the printer attached to this serial port belongs. These values are fixed, and cannot be changed by the user.ro
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.2
printerGroupGroups printers attached to different ports. Printers in the same group will share the printing load for printing requests to that group of printers. E.g., setting the NPort 6000 series device server's serial ports 1, 3, and 6 for 'Group01' will allow the printers attached to these three ports to act essentially as one printer.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.3
printerQueueNameRawSpecify the name of the print queue (in RAW mode).rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.4
printerQueueNameASCIISpecify the name of the print queue (in ASCII mode).rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.5
printerAppendFromFeedSpecify paging.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.6
dial
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.8
dialTableThe Dial In/Out table.
SEQUENCE OF DialEntry
.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1
dialEntryThe Dial In/Out entry.
DialEntry
.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1
dialTERMBINModeSelect Yes to enable a Binary Terminal connection.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.1
dialPPPDModeSelect Yes to enable a PPPD connection.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.2
dialSLIPDModeSelect Yes to enable a SLIPD Terminal connection.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.3
dialAuthTypeThe dial in/out authentication type.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.4
dialDisconnectByIf this field is set to 'dcd-off,' the connection will be disconnected when the DCD signal is off. If this field is set to 'dsr-off,' the connection will be disconnected when the DSR signal is off.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.5
dialDestinationIpAddressDestination IP address is the IP address of the remote dial-in/dial-out server.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.6
dialSourceIpAddressSource IP address is IP address of this serial port. The NPort 6000 series device server will automatically assign an IP address for the port. We recommend leaving this field blank.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.7
dialIpNetmaskThe IP netmask used for dial-in/dial-out networks (PPP or SLIP).rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.8
dialTcpIpCompressionDepends on whether the remote user's application requests compression.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.9
dialInactivityTime0 ms: TCP connection will not be closed if the serial line becomes idle. 1-65535 ms: The NPort 6000 series device server automatically closes the TCP connection if there is no serial data activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another TCP connection.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.10
dialLinkQualityReportChoose YES if you are using software to collect Link quality information.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.11
dialOutgoingPAPIDDial-out user ID account.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.12
dialPAPPasswordDial-out user password.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.13
dialIncomingPAPCheckThe Dial in/out incoming PAP check type.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.14
dataPacking
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.4.1.3
dataPackingPortTableThe Data Packing table.
SEQUENCE OF DataPackingPortEntry
.1.3.6.1.4.1.8691.2.8.1.4.1.3.1
dataPackingPortEntryThe Data Packing entry.
DataPackingPortEntry
.1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1
portPacketLengthIf the value is 0, the Delimiter Process will be used, regardless of the length of the data packet. If the data length (in bytes) matches the configured value, the data will be forced out. The data length can be configured from 0 to 1024 bytes. Set to 0 if you do not need to limit the length.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.1
portDelimiter1EnableEnable the first delimiter character.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.2
portDelimiter1The first delimiter character, in hex decimal.rw
DisplayString
.1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.3
portDelimiter2EnableEnable the second delimiter character.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.4
portDelimiter2The second delimiter character, in hex decimal.rw
DisplayString
.1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.5
portDelimiterProcess'delimiterAddOne' or 'delimiterAddTwo': The data will be transmitted when an additional byte (for 'delimiterAddOne'), or an additional 2 bytes (for 'delimiterAddTwo') of data is received after receiving the Delimiter. 'stripDelimiter': When the delimiter is received, the Delimiter is deleted (i.e., stripped), and the remaining data is transmitted. 'doNothing': The data will be transmitted when the delimiter is received.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.6
portForceTransmit0: Disable the force transmit timeout. 1 to 65535: Forces the NPort 6000 series device server's TCP/IP protocol software to try to pack serial data received during the specified time into the same data frame.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.7
comParamSetting
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.4.2
comParamPortTableThe Communication Parameters table.
SEQUENCE OF ComParamPortEntry
.1.3.6.1.4.1.8691.2.8.1.4.2.1
comParamPortEntryThe Communication Parameters entry.
ComParamPortEntry
.1.3.6.1.4.1.8691.2.8.1.4.2.1.1
portAliasPort alias is included to allow easy identification of the serial devices that are connected to NPort 6000 series device server's serial port.rw
DisplayString
.1.3.6.1.4.1.8691.2.8.1.4.2.1.1.1
portInterfaceThe serial interface that the port works on.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.2.1.1.2
portBaudRateThe port's speed in bits per second. You can choose a standard baud rate by indexing.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.2.1.1.3
portBaudRateManualThe port's speed in bits per second. You can specify a baud rate manually.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.2.1.1.4
portDataBitsThe number of bits in a character for the port.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.2.1.1.5
portStopBitsThe number of stop bits for the port.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.2.1.1.6
portParityThe parity bit for the port.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.2.1.1.7
portFlowControlThe flow-control method for the port.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.2.1.1.8
portFIFOEnable or disable the port's FIFO.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.2.1.1.9
dataBuffering
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.4.3
dataBufferingPortTableThe Data Buffering/Log table.
SEQUENCE OF DataBufferingPortEntry
.1.3.6.1.4.1.8691.2.8.1.4.3.1
dataBufferingPortEntryThe Data Buffering/Log entry.
DataBufferingPortEntry
.1.3.6.1.4.1.8691.2.8.1.4.3.1.1
portBufferingEnableEnable off-line port buffering.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.3.1.1.1
portBufferingLocationThe location of off-line port buffering.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.3.1.1.2
portBufferingSDFileSizeThe maximum file size of off-line port buffering, in MBytes, if the location is set to 'sdCard.'rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.4.3.1.1.3
portSerialDataLoggingEnableEnable or disable serial data logging for the port.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.3.1.1.4
modemSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.4.4
modemSettingsPortTableThe Modem Settings table.
SEQUENCE OF ModemSettingsPortEntry
.1.3.6.1.4.1.8691.2.8.1.4.4.1
modemSettingsPortEntryThe Modem Settings entry.
ModemSettingsPortEntry
.1.3.6.1.4.1.8691.2.8.1.4.4.1.1
portEnableModemEnable or disable modem for this port.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.4.1.1.1
portInitialStringSet the modem's initial string to establish the connection. E.g., 'AT&S0=1' for auto-answer.rw
DisplayString
.1.3.6.1.4.1.8691.2.8.1.4.4.1.1.2
portDialUpSet the modem's dial-up AT command string.rw
DisplayString
.1.3.6.1.4.1.8691.2.8.1.4.4.1.1.3
portPhoneNumberSet the number used to dial out.rw
DisplayString
.1.3.6.1.4.1.8691.2.8.1.4.4.1.1.4
welcomeMessage
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.4.5
portEnableWelcomeMessageEnable or disable the welcome message.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.4.5.1
portMessageSet up a welcome message to greet dial-in users.rw
DisplayString
.1.3.6.1.4.1.8691.2.8.1.4.5.2
sysManagement
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.5
miscNetworkSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.5.1
accessibleIp
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.5.1.1
enableAccessibleIpListEnable or disable the entire accessible IP list.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.1.1.1
accessibleIpListTableAccessible IP List table.
SEQUENCE OF AccessibleIpListEntry
.1.3.6.1.4.1.8691.2.8.1.5.1.1.2
accessibleIpListEntryAccessible IP List entry.
AccessibleIpListEntry
.1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1
accessibleIpListIndexAccessible IP List index.ro
INTEGER
.1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1.1
activeAccessibleIpListEnable or disable this accessible IP entry.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1.2
accessibleIpListAddressAccessible IP address. This value can be the IP address of a single host if the netmask is set to '255.255.255.255,' or it can be a network address.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1.3
accessibleIpListNetmaskAccessible IP address netmask. The IP address and netmask are used to specify a group of remote hosts.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1.4
snmpAgentSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.5.1.2
snmpEnableEnable or disable SNMP agent.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.1.2.1
snmpContactNameThe SNMP contact information usually includes an emergency contact name and telephone or pager number.rw
DisplayString
.1.3.6.1.4.1.8691.2.8.1.5.1.2.2
snmpLocationSpecify the location string for SNMP agents, such as the NPort 6000 series device server. This string is usually set to the street address where the NPort 6000 series device server is physically located.rw
DisplayString
.1.3.6.1.4.1.8691.2.8.1.5.1.2.3
dDNS
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.5.1.3
dDNSEnableEnable or disable the DDNS function.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.1.3.1
dDNSServerAddressThe DDNS server address. The DDNS is serviced by a 3-party provider. To use the DDNS function, you may need to obtain a user account from the server.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.1.3.2
dDNSHostNameThe host name of the machine to be registered to the DDNS server.rw
DisplayString
.1.3.6.1.4.1.8691.2.8.1.5.1.3.3
dDNSUserNameThe user account provided by the DDNS server.rw
DisplayString
.1.3.6.1.4.1.8691.2.8.1.5.1.3.4
dDNSPasswordThe user password provided by the DDNS server.rw
DisplayString
.1.3.6.1.4.1.8691.2.8.1.5.1.3.5
hostTable
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.5.1.4
hostTableTableHost Table.
SEQUENCE OF HostTableEntry
.1.3.6.1.4.1.8691.2.8.1.5.1.4.1
hostTableEntryHost Table entry.
HostTableEntry
.1.3.6.1.4.1.8691.2.8.1.5.1.4.1.1
hostTableIndexThe Host Table index.ro
INTEGER
.1.3.6.1.4.1.8691.2.8.1.5.1.4.1.1.1
hostNameThe host name of the host table entry.rw
DisplayString
.1.3.6.1.4.1.8691.2.8.1.5.1.4.1.1.2
hostIpAddressRelated IP address of the host table entry.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.5.1.4.1.1.3
routeTable
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.5.1.5
routeTableTableRoute Table.
SEQUENCE OF RouteTableEntry
.1.3.6.1.4.1.8691.2.8.1.5.1.5.1
routeTableEntryRoute Table entry.
RouteTableEntry
.1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1
routeTableIndexThe Route Table index.ro
INTEGER
.1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.1
gatewayRouteTableThe gateway property of the route table entry.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.2
destinationRouteTableThe destination IP address of the route table entry. This value can be the IP address of a single host if the netmask set to '255.255.255.255,' or it can be a network address.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.3
netmaskRouteTableThe destination netmask of the route table entry.rw
IpAddress
.1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.4
metricRouteTableThe routing metric for this route. The semantics of this metric are determined by the routing-protocol. Normally, it represents the cost for the destination.rw
INTEGER
.1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.5
interfaceRouteTableThe value that identifies the local interface through which the next hop of this route should be reached.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.6
userTable
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.5.1.6
userTableTableUser Table.
SEQUENCE OF UserTableEntry
.1.3.6.1.4.1.8691.2.8.1.5.1.6.1
userTableEntryUser Table entry.
UserTableEntry
.1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1
userTableIndexThe User Table index.ro
INTEGER
.1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1.1
userNameUserTableThe user name of this entry.rw
DisplayString
.1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1.2
passwordUserTableThe password of this user entry.rw
DisplayString
.1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1.3
phoneNumberUserTableThe phone number of this user entry.rw
DisplayString
.1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1.4
authenticationServer
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.5.1.7
radiusServerIpThe IP address or domain name of the RADIUS server.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.5.1.7.1
radiusKeyRADIUS password. Must be the same as in the RADIUS server.rw
DisplayString
.1.3.6.1.4.1.8691.2.8.1.5.1.7.2
udpPortAuthenticationServerThe UDP port of the RADIUS server.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.1.7.3
radiusAccountingEnable or disable RADIUS accounting.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.1.7.4
sysLogSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.5.1.8
sysLocalLogLog the following events to the system log: System Cold Start, System Warm Start.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.1.8.1
networkLocalLogLog the following events to the system log: DHCP/BOOTP/PPPoE Get IP/Renew, NTP, Mail Fail, NTP Connect Fail, DHCP Fail, IP Conflict, Ethernet Link Down.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.1.8.2
configLocalLogLog the following events to the system log: Login Fail, IP Changed, Password Changed, Config Changed, Firmware Upgrade, SSL Key Import, Config Import, Config Export.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.1.8.3
opModeLocalLogLog the following op-mode events to the system log: Connect, Disconnect, Authentication Fail, Restart.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.1.8.4
autoWarningSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.5.2
eventSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.5.2.1
mailWarningColdStartRefers to starting the system from power off (contrast this with warm start). When performing a cold start, the NPort 6000 series device server will automatically issue an auto warning message by e-mail after booting up.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.2.1.1
mailWarningWarmStartRefers to restarting the NPort 6000 without turning the power off. When performing a warm start, the NPort 6000 series device server will automatically send an e-mail after rebooting.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.2.1.2
mailWarningAuthFailureThe user inputs a wrong password from the Console or Administrator. When authentication failure occurs, the NPort 6000 series device server will immediately send an e-mail.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.2.1.3
mailWarningIpChangedThe user has changed the NPort 6000 series device server's IP address. When the IP address changes, the NPort 6000 series device server will send an e-mail with the new IP address before it reboots. If the NPort 6000 series device server is unable to send an e-mail message to the mail server within 15 seconds, it will reboot anyway, and abort the e-mail auto warning.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.2.1.4
mailWarningPasswordChangedThe user has changed the NPort 6000 series device server's password. When the password changes, the NPort 6000 series device server will send an e-mail with the password changed notice before it reboots. If the NPort 6000 series device server is unable to send an e-mail message to the mail server within 15 seconds, it will reboot anyway, and abort the e-mail auto warning.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.2.1.5
trapServerColdStartRefers to starting the system from power off (contrast this with warm start). When performing a cold start, the NPort 6000 series device server will automatically issue an auto warning message by sending an SNMP trap after booting up.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.2.1.6
trapServerWarmStartRefers to restarting the NPort 6000 without turning the power off. When performing a warm start, the NPort 6000 series device server will automatically send an SNMP trap after rebooting.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.2.1.7
trapServerAuthFailureThe user inputs a wrong password from the Console or Administrator. When authentication failure occurs, the NPort 6000 series device server will immediately send an SNMP trap.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.2.1.8
alarmServerEthernet1LinkDownWhen the built-in link1 port is off, the NPort 6000 series device server will automatically raise a d-out alarm.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.2.1.9
alarmServerEthernet2LinkDownThe NPort 6000 series device server can provide an extra Ethernet port via the network module. When the first port on the network module is off, the NPort 6000 series device server will automatically raise a d-out alarm.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.2.1.10
alarmServerEthernet3LinkDownThe NPort 6000 series device server can provide an extra Ethernet port via the network module. When the second port on the network module is off, the NPort 6000 series device server will automatically raise a d-out alarm.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.2.1.11
serialEventSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.5.2.2
portEventSettingsTablePort Event Settings Table.
SEQUENCE OF PortEventSettingsEntry
.1.3.6.1.4.1.8691.2.8.1.5.2.2.1
portEventSettingsEntryPort Event Settings entry.
PortEventSettingsEntry
.1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1
mailDCDchangeA change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indicates that the connection line is down. When the DCD signal changes to low, the NPort 6000 series device server will immediately send an e-mail message.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.1
trapDCDchangeA change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indicates that the connection line is down. When the DCD signal changes to low, the NPort 6000 series device server will immediately send an SNMP trap.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.2
alarmDCDchangeA change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indicates that the connection line is down. When the DCD signal changes to low, the NPort 6000 series device server will immediately raise a d-out alarm.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.3
mailDSRchangeA change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it indicates that the data communication equipment is powered down. When the DSR signal changes to low, the NPort 6000 series device server will immediately send an e-mail message.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.4
trapDSRchangeA change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it indicates that the data communication equipment is powered down. When the DSR signal changes to low, the NPort 6000 series device server will immediately send an SNMP trap.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.5
alarmDSRchangeA change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it indicates that the data communication equipment is powered down. When the DSR signal changes to low, the NPort 6000 series device server will immediately raise a d-out alarm.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.6
emailAlert
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.5.2.3
emailWarningMailServerThe e-mail server's IP address or domain name of the e-mail warning function.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.5.2.3.1
emailRequiresAuthenticationSet if the mail server requires user login.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.2.3.2
emailWarningUserNameThe user name used to log into the mail server if authentication is required.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.5.2.3.3
emailWarningPasswordThe password used to log into the mail server if authentication is required.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.5.2.3.4
emailWarningFromEmailThe e-mail address to be filled in the 'From' field of the auto-warning e-mail.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.5.2.3.5
emailWarningFirstEmailAddrThe first email address to where the auto-warning e-mail is to be sent.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.5.2.3.6
emailWarningSecondEmailAddrThe second email address to where the auto-warning e-mail is to be sent.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.5.2.3.7
emailWarningThirdEmailAddrThe third email address to where the auto-warning e-mail is to be sent.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.5.2.3.8
emailWarningFourthEmailAddrThe fourth email address to where the auto-warning e-mail is to be sent.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.5.2.3.9
snmpTrap
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.5.2.4
snmpTrapReceiverIpSNMP trap receiver IP address or domain name.rw
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.5.2.4.1
trapVersionSNMP trap version used for the auto-warning function.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.2.4.2
maintenance
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.5.3
consoleSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.5.3.1
httpConsoleEnable or disable HTTP console.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.3.1.1
httpsConsoleEnable or disable HTTPS console.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.3.1.2
telnetConsoleEnable or disable Telnet console.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.3.1.3
sshConsoleEnable or disable SSH console.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.3.1.4
lcmReadOnlyProtectEnable or disable LCM read-only protection. If the LCM panel is under read-only protection, users can only view the configurations from the LCM panel. Otherwise, by default, users can modify the settings directly on the LCM panel.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.3.1.5
resetButtonFunctionEnable or disable reset button protection. You can disable the hardware reset button after the NPort 6000 series device server has been restarted for 60 seconds.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.3.1.6
loadFactoryDefault
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.5.3.2
loadFactoryDefaultSettingThis function will reset all of the NPort 6000 series device server's settings to the factory default values. Be aware that previous settings will be lost. Selecting Reset to factory default (excluding IP configuration) will reset all settings except the IP configuration to factory defaults. Selecting Reset to factory default will reset all settings including the IP configuration to factory defaults.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.5.3.2.1
sysStatus
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.6
s2eConnections
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.6.1
monitorRemoteIpTableSerial to Network Connections Remote IP table.
SEQUENCE OF MonitorRemoteIpEntry
.1.3.6.1.4.1.8691.2.8.1.6.1.1
monitorRemoteIpEntrySerial to Network Connections Remote IP entry.
MonitorRemoteIpEntry
.1.3.6.1.4.1.8691.2.8.1.6.1.1.1
remoteIpIndexSerial to Network Connections Remote IP index.ro
INTEGER
.1.3.6.1.4.1.8691.2.8.1.6.1.1.1.1
monitorRemoteIpThe remote IP currently connecting to this port.ro
IpAddress
.1.3.6.1.4.1.8691.2.8.1.6.1.1.1.2
serialPortStatus
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.6.2
monitorSerialPortStatusTableSerial Port Status table.
SEQUENCE OF MonitorSerialPortStatusEntry
.1.3.6.1.4.1.8691.2.8.1.6.2.1
monitorSerialPortStatusEntrySerial Port Status entry.
MonitorSerialPortStatusEntry
.1.3.6.1.4.1.8691.2.8.1.6.2.1.1
monitorTxCountView the number of bytes transmitted from the port since the last time the port was initialized.ro
INTEGER
.1.3.6.1.4.1.8691.2.8.1.6.2.1.1.1
monitorRxCountView the number of bytes received by the port since the last time the port was initialized.ro
INTEGER
.1.3.6.1.4.1.8691.2.8.1.6.2.1.1.2
monitorTxTotalCountView the number of bytes transmitted from the port since the last time the system was initialized.ro
INTEGER
.1.3.6.1.4.1.8691.2.8.1.6.2.1.1.3
monitorRxTotalCountView the number of bytes received by the port since the last time the system was initialized.ro
INTEGER
.1.3.6.1.4.1.8691.2.8.1.6.2.1.1.4
monitorDSRView the current DSR status of this port.ro
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.2.1.1.5
monitorDTRView the current DTR status of this port.ro
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.2.1.1.6
monitorRTSView the current RTS status of this port.ro
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.2.1.1.7
monitorCTSView the current CTS status of this port.ro
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.2.1.1.8
monitorDCDView the current DCD status of this port.ro
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.2.1.1.9
serialPortErrorCount
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.6.3
monitorSerialPortErrorCountTableSerial Port Error Count table.
SEQUENCE OF MonitorSerialPortErrorCountEntry
.1.3.6.1.4.1.8691.2.8.1.6.3.1
monitorSerialPortErrorCountEntrySerial Port Error Count entry.
MonitorSerialPortErrorCountEntry
.1.3.6.1.4.1.8691.2.8.1.6.3.1.1
monitorErrorCountFrameView the number of 'Frame' errors for this port.ro
INTEGER
.1.3.6.1.4.1.8691.2.8.1.6.3.1.1.1
monitorErrorCountParityView the number of 'Parity' errors for this port.ro
INTEGER
.1.3.6.1.4.1.8691.2.8.1.6.3.1.1.2
monitorErrorCountOverrunView the number of 'Overrun' errors for this port.ro
INTEGER
.1.3.6.1.4.1.8691.2.8.1.6.3.1.1.3
monitorErrorCountBreakView the number of 'Break' errors for this port.ro
INTEGER
.1.3.6.1.4.1.8691.2.8.1.6.3.1.1.4
serialPortSettings
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.6.4
monitorSerialPortSettingsTableSerial Port Settings table.
SEQUENCE OF MonitorSerialPortSettingsEntry
.1.3.6.1.4.1.8691.2.8.1.6.4.1
monitorSerialPortSettingsEntrySerial Port Settings entry.
MonitorSerialPortSettingsEntry
.1.3.6.1.4.1.8691.2.8.1.6.4.1.1
monitorBaudRateView the current baudrate of the port.ro
INTEGER
.1.3.6.1.4.1.8691.2.8.1.6.4.1.1.1
monitorDataBitsView the number of bits per byte for the port.ro
INTEGER
.1.3.6.1.4.1.8691.2.8.1.6.4.1.1.2
monitorStopBitsView the number of stop bits for the port.ro
DisplayString (SNMPv2-TC)
.1.3.6.1.4.1.8691.2.8.1.6.4.1.1.3
monitorParityView the parity bit for the port.ro
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.4.1.1.4
monitorRTSCTSFlowControlView if the port is using RTS/CTS flow control.ro
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.4.1.1.5
monitorXONXOFFFlowControlView if the port is using XON/XOFF flow control.ro
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.4.1.1.6
monitorDTRDSRFlowControlView if the port is using DTR/DSR flow control.ro
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.4.1.1.7
monitorFIFOView FIFO status of this port.ro
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.4.1.1.8
monitorInterfaceView the serial interface that the port is using.ro
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.4.1.1.9
relayOutputStatus
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.6.5
relayOutputEthernet1LinkDownThe relay dout status of the event that the built- in LAN port is off.ro
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.5.1
ethernet1LinkDownAcknowledgeAcknowledge the event that the built-in LAN port is off. Acknowledgement will clear the d-out alarm before you can actually fix the problem.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.5.2
relayOutputEthernet2LinkDownThe relay dout status of the event that the first LAN port of the network module is off.ro
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.5.3
ethernet2LinkDownAcknowledgeAcknowledge the event that the first LAN port of the network module is off. Acknowledgement will clear the d-out alarm before you can actually fix the problem.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.5.4
relayOutputEthernet3LinkDownThe relay dout status of the event that the second LAN port of the network module is off.ro
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.5.5
ethernet3LinkDownAcknowledgeAcknowledge the event that the second LAN port of the network module is off. Acknowledgement will clear the d-out alarm before you can actually fix the problem.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.5.6
portDCDChangedStatusTableDCD changed table.
SEQUENCE OF PortDCDChangedStatusEntry
.1.3.6.1.4.1.8691.2.8.1.6.5.7
portDCDChangedStatusEntryDCD changed entry.
PortDCDChangedStatusEntry
.1.3.6.1.4.1.8691.2.8.1.6.5.7.1
portDCDChangedStatusThe relay dout status of the event that the DCD signal of the port is changed.ro
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.5.7.1.1
portDCDChangedAcknowledgeAcknowledge the event that the DCD signal of the port is changed. Acknowledgement will clear the d-out alarm before you can actually fix the problem.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.5.7.1.2
portDSRChangedStatusTableDSR changed Table.
SEQUENCE OF PortDSRChangedStatusEntry
.1.3.6.1.4.1.8691.2.8.1.6.5.8
portDSRChangedStatusEntryDSR changed entry.
PortDSRChangedStatusEntry
.1.3.6.1.4.1.8691.2.8.1.6.5.8.1
portDSRChangedStatusThe relay dout status of the event that the DSR signal of the port is changed.ro
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.5.8.1.1
portDSRChangedAcknowledgeAcknowledge the event that the DSR signal of the port is changed. Acknowledgement will clear the d-out alarm before you can actually fix the problem.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.6.5.8.1.2
saveConfiguration
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.7
saveConfigSave the applied configuration to the NPort 6000 series device server.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.7.1
restart
OBJECT IDENTIFIER
.1.3.6.1.4.1.8691.2.8.1.8
restartPortsRestart serial port. Restarting will cause port reseting.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.8.1
restartSystemRestart the NPort 6000 series device server. Be sure to save all of your configuration changes before you restart the system. Otherwise, all of the changes will be lost.rw
Enumeration
.1.3.6.1.4.1.8691.2.8.1.8.2
MOXA-NP6000-MIB - SNMP MIB Reference | MIBs Explorer