MICOM-NODE-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
1127
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
1127 total| Object Name |
|---|
micom OBJECT IDENTIFIER .1.3.6.1.4.1.335 |
RFC1155-SMI Unknown .1.3.6.1.4.1.335 |
mcmEventConnectA connection has been established between the specified
pair of unit ports. TRAP-TYPE .1.3.6.1.4.1.335.0.1 |
mcmEventDisconnectThe connection between the specified pair of unit ports
has been broken. TRAP-TYPE .1.3.6.1.4.1.335.0.2 |
mcmEventQueueEntryA port has been placed in a first-come first-served queue
for the next available port in the requested class. TRAP-TYPE .1.3.6.1.4.1.335.0.3 |
mcmEventCallFailA matrix connection made by the local port did not complete
successfully (for example, the password was incorrect). TRAP-TYPE .1.3.6.1.4.1.335.0.4 |
mcmEventDDSInServiceThe unit's ISU module is back in service, and the associated
link is up. TRAP-TYPE .1.3.6.1.4.1.335.0.5 |
mcmEventDDSOutServiceThe unit's ISU module is out of service, and the associated
link is down. TRAP-TYPE .1.3.6.1.4.1.335.0.6 |
mcmEventDDSLoopTestThe telephone company has placed the unit's ISU module
into a loop test mode. TRAP-TYPE .1.3.6.1.4.1.335.0.7 |
mcmEventADBConnectMadeThe unit's modem module has completed a dial backup
connection, and the associated link is up. TRAP-TYPE .1.3.6.1.4.1.335.0.8 |
mcmEventADBConnectDropThe unit's modem module has dropped the dial line
connection due to bad lines, Data Terminal Ready
dropped, or Carrier Detect lost. As a result, the
associated link is down. TRAP-TYPE .1.3.6.1.4.1.335.0.9 |
mcmEventForcedDialModeThe unit's modem module has been placed into the forced
dial mode. The associated link will always be established
over the dial lines. TRAP-TYPE .1.3.6.1.4.1.335.0.10 |
mcmEventForcedLeaseModeThe unit's modem module has been placed into the forced
lease mode. The associated link will always be established
over the lease lines; no dial backup can occur. TRAP-TYPE .1.3.6.1.4.1.335.0.11 |
mcmEventLeasedConnectThe unit's modem module has established communications
over the lease lines, and the associated link is up. TRAP-TYPE .1.3.6.1.4.1.335.0.12 |
mcmEventLeaseLineRetryThe unit's modem module has started operating on the
lease lines while the dial line connection is still
established. TRAP-TYPE .1.3.6.1.4.1.335.0.13 |
mcmEventLinkRestartCommunications on the local side of the associated link
have been restarted. TRAP-TYPE .1.3.6.1.4.1.335.0.14 |
mcmEventRemoteLinkRestartCommunications on the remote end of the specified link
have been restarted. TRAP-TYPE .1.3.6.1.4.1.335.0.15 |
mcmEventNoADBNumberNo number has been configured for auto dial backup
for the specified link. TRAP-TYPE .1.3.6.1.4.1.335.0.16 |
mcmEventADBNoRXDialToneThe dial backup function on the unit's modem module
went off-hook on the Rx line, and a dial tone was not
detected. TRAP-TYPE .1.3.6.1.4.1.335.0.17 |
mcmEventADBNoTxDialToneThe dial backup function on the unit's modem module
went off-hook on the Tx line, and a dial tone was not
detected. TRAP-TYPE .1.3.6.1.4.1.335.0.18 |
mcmEventADBRxDialingThe dial backup function on the unit's modem module
is dialing the telephone number for the Rx line. TRAP-TYPE .1.3.6.1.4.1.335.0.19 |
mcmEventADBTxDialingThe dial backup function on the unit's modem module
is dialing the telephone number for the Tx line. TRAP-TYPE .1.3.6.1.4.1.335.0.20 |
mcmEventADBNoAnswerThe dial backup function on the unit's modem module
did not receive an answer tone after placing a call
on a dial line. TRAP-TYPE .1.3.6.1.4.1.335.0.21 |
mcmEventADBRxBusyThe dial backup function on the unit's modem module
has detected a busy signal on the Rx dial line. TRAP-TYPE .1.3.6.1.4.1.335.0.22 |
mcmEventADBTxBusyThe dial backup function on the unit's modem module
has detected a busy signal on the Tx dial line. TRAP-TYPE .1.3.6.1.4.1.335.0.23 |
mcmEventADBRxRingingThe dial backup function on the unit's modem module
has detected an incoming call on the Rx dial line. TRAP-TYPE .1.3.6.1.4.1.335.0.24 |
mcmEventADBTxRingingThe dial backup function on the unit's modem module
has detected an incoming call on the Tx dial line. TRAP-TYPE .1.3.6.1.4.1.335.0.25 |
mcmEventADBRingDetectA call is being transmitted or received by the dial
backup function of the unit's modem module. TRAP-TYPE .1.3.6.1.4.1.335.0.26 |
mcmEventADBNoDialToneThe dial backup function on the unit's modem module
went off-hook on either the Tx or Rx dial line and
failed to detect a dial tone. TRAP-TYPE .1.3.6.1.4.1.335.0.27 |
mcmEventVoiceBusyOutA voice channel has been placed in the busyout state.
This can be caused by: one, the link experiencing a loss
of sync; two, force disable or force disconnect commands
having been executed; or three, an operator placing the
channel into the busyout state using a force-busy command. TRAP-TYPE .1.3.6.1.4.1.335.0.28 |
mcmEventVoiceClearBusyThe condition that caused the voice channel busyout
has been cleared or terminated. TRAP-TYPE .1.3.6.1.4.1.335.0.29 |
mcmEventADBRxConnectThe dial backup function on the unit's modem module
has answered a call over the Rx dial line, and the Rx
dial backup connection is made. TRAP-TYPE .1.3.6.1.4.1.335.0.30 |
mcmEventADBTxConnectThe dial backup function on the unit's modem module
has answered a call over the Tx dial line, and the Tx
dial backup connection is made. TRAP-TYPE .1.3.6.1.4.1.335.0.31 |
mcmEventADBLineBusyThe dial backup function on the unit's modem module has
encountered a busy signal over the Tx of Tx lines. TRAP-TYPE .1.3.6.1.4.1.335.0.32 |
mcmEventADBRIDetectThe dial backup function on the unit's modem module has
detected an incoming call. TRAP-TYPE .1.3.6.1.4.1.335.0.33 |
mcmEventADBAbortA call placed on the dial lines by the dial backup
function of the unit's modem module has failed. This
message is issued by the call-originating unit. TRAP-TYPE .1.3.6.1.4.1.335.0.34 |
mcmEventLeasedLineOOSThe unit's modem module is unable to communicate with
the remote modem over the lease lines. It is Out Of
Service (OOS). TRAP-TYPE .1.3.6.1.4.1.335.0.35 |
mcmEventNewDLCIA DLCI (Data Link Connection Identifier) was added. TRAP-TYPE .1.3.6.1.4.1.335.0.36 |
mcmEventDLCIActiveA DLCI (Data Link Connection Identifier) was activated. TRAP-TYPE .1.3.6.1.4.1.335.0.37 |
mcmEventConfigurationUpdateThe node's configuration has been successfully written to
the FLASH DRAM (applicable to 3K and 5KT Pro platforms). TRAP-TYPE .1.3.6.1.4.1.335.0.38 |
mcmEventDLCIConnectA DLCI connection has been established between a pair
of unit ports. TRAP-TYPE .1.3.6.1.4.1.335.0.39 |
mcmEventDLCIDisconnectThe DLCI connection between the specified pair of unit
ports has been broken. TRAP-TYPE .1.3.6.1.4.1.335.0.40 |
mcmAlarmSystemResetThe specified unit has been reset (either warm or cold start). TRAP-TYPE .1.3.6.1.4.1.335.0.101 |
mcmAlarmBatteryLowThe CMOS RAM backup battery in the specified unit is in need
of replacement. TRAP-TYPE .1.3.6.1.4.1.335.0.102 |
mcmAlarmCmosErrorThe specified unit encountered a problem writing to the
configuration area (CMOS RAM). TRAP-TYPE .1.3.6.1.4.1.335.0.103 |
mcmAlarmSystemFlowControlThe specified unit is turning off data input from its ports
to prevent buffer overflow. This condition generally occurs
due to insufficient data throughput across the link. TRAP-TYPE .1.3.6.1.4.1.335.0.104 |
mcmAlarmNodeTableFullThere are no more available node numbers that can be
assigned to new units on this network. TRAP-TYPE .1.3.6.1.4.1.335.0.105 |
mcmAlarmDuplicateNodeNumberTwo nodes in the network have the same node ID number. TRAP-TYPE .1.3.6.1.4.1.335.0.106 |
mcmAlarmInvalidLinkCfgAn attempt has been made to connect a mux link to a port
configured other than a mux link, or vice versa. TRAP-TYPE .1.3.6.1.4.1.335.0.107 |
mcmAlarmBufferOverFlowData has been lost for a specific port on the specified
unit due to an buffer overflow condition. TRAP-TYPE .1.3.6.1.4.1.335.0.120 |
mcmAlarmLinkDownThe unit has timed out (40 secs) waiting for synchronization
to be acquired on the link. Check the cabling, modem, and
remote unit for the source of the problem. TRAP-TYPE .1.3.6.1.4.1.335.0.121 |
mcmAlarmSyncLossSynchronization has been lost with the remote unit attached
to the specified link. TRAP-TYPE .1.3.6.1.4.1.335.0.122 |
mcmAlarmSyncAcquireSynchronization has been achieved with the remote unit
attached to the specified link. TRAP-TYPE .1.3.6.1.4.1.335.0.123 |
mcmAlarmCarrierLossThe carrier signal has been lost on the specified link
(as detected from the CD interface control signal). TRAP-TYPE .1.3.6.1.4.1.335.0.124 |
mcmAlarmCarrierAcquireThe carrier signal has been detected on the specified
link (after the carrier had been previously lost). TRAP-TYPE .1.3.6.1.4.1.335.0.125 |
mcmAlarmLineAlarmA high error rate is occurring on the specified link. TRAP-TYPE .1.3.6.1.4.1.335.0.126 |
mcmAlarmSyncChannelStoppedThe specified synchronous port has lost its output
clock or the input end of the frame is missing. TRAP-TYPE .1.3.6.1.4.1.335.0.127 |
mcmAlarmLANCardUpThe LAN card is operating and is available for use
(after a previous LAN card down). TRAP-TYPE .1.3.6.1.4.1.335.0.128 |
mcmAlarmLANCardDownThe LAN card is not operating or is not available
for use. TRAP-TYPE .1.3.6.1.4.1.335.0.129 |
mcmAlarmX21CallFailThe specified unit was unable to complete a call over the
X.21 network from the port indicated. TRAP-TYPE .1.3.6.1.4.1.335.0.130 |
mcmAlarmPrimaryESIDownWhen secondary interconnect links are configured on
a node, this trap is sent if the primary link has timed
out waiting for synchronization to be acquired on the
primary link. TRAP-TYPE .1.3.6.1.4.1.335.0.131 |
mcmAlarmStartESISecondaryThe primary link has been down for a preset interval,
and now the node is attempting to bring up the secondary
link. TRAP-TYPE .1.3.6.1.4.1.335.0.132 |
mcmAlarmSecondaryUpSynchronization has been achieved on the secondary link
and data is now being transferred across it. TRAP-TYPE .1.3.6.1.4.1.335.0.133 |
mcmAlarmSecondaryTerminatedThe primary link has been back up for a preset interval
with data being transferred across it. The node is now
dropping the give secondary link. TRAP-TYPE .1.3.6.1.4.1.335.0.134 |
mcmAlarmSecondaryDownThe secondary interconnect link has timed out waiting
for synchronization to be acquired, after the link had
been established with data being transferred on it. TRAP-TYPE .1.3.6.1.4.1.335.0.135 |
mcmAlarmSecondaryResetCommunications on the secondary interconnect link have
been restarted. TRAP-TYPE .1.3.6.1.4.1.335.0.136 |
mcmAlarmPrimaryESIUpSynchronization has been achieved on the primary link
and data is now being transferred across it. TRAP-TYPE .1.3.6.1.4.1.335.0.137 |
mcmAlarmDLCIDeletedA DLCI has been deleted. TRAP-TYPE .1.3.6.1.4.1.335.0.138 |
mcmAlarmDLCIInactiveA DLCI was inactivated. TRAP-TYPE .1.3.6.1.4.1.335.0.139 |
mcmAlarmT1NetworkRedAlarmA T1 Network (DS-1) Red Alarm is generated when a
Receive-Loss-of-Frame is detected. Voice signaling is
static when this condition occurs. TRAP-TYPE .1.3.6.1.4.1.335.0.140 |
mcmAlarmT1NetworkRedClearA T1 Network (DS-1) Red Alarm condition has cleared. TRAP-TYPE .1.3.6.1.4.1.335.0.141 |
mcmAlarmT1LocalRedAlarmA T1 Local (DSX-1) Red Alarm is generated when a
Receive-Loss-of-Frame is detected. Voice signaling is
static when this condition occurs. TRAP-TYPE .1.3.6.1.4.1.335.0.142 |
mcmAlarmT1LocalRedClearA T1 Local (DSX-1) Red Alarm condition has cleared. TRAP-TYPE .1.3.6.1.4.1.335.0.143 |
mcmAlarmT1NetworkYellowAlarmA T1 Network (DS-1) Yellow Alarm is generated and
transmitted to a remote location when a T1 DS-1 Red
Alarm is detected. TRAP-TYPE .1.3.6.1.4.1.335.0.144 |
mcmAlarmT1NetworkYellowClearA T1 Network (DS-1) Yellow Alarm condition has cleared. TRAP-TYPE .1.3.6.1.4.1.335.0.145 |
mcmAlarmT1LocalYellowAlarmA T1 Local (DSX-1) Yellow Alarm is generated and
transmitted to a remote location when a T1 DSX-1 Red
Alarm is detected. TRAP-TYPE .1.3.6.1.4.1.335.0.146 |
mcmAlarmT1LocalYellowClearA T1 Local (DSX-1) Yellow Alarm condition has cleared. TRAP-TYPE .1.3.6.1.4.1.335.0.147 |
mcmAlarmT1NetworkAlarmIndA T1 Network (DS-1) Alarm Indication is generated with the
detection of the Out-of-Frame condition and when all 1's
are detected on the line. The Alarm Indication Signal (AIS)
is generated by the T1 module when the Internal Digital
Loopback test is invoked. TRAP-TYPE .1.3.6.1.4.1.335.0.148 |
mcmAlarmT1NetworkAlarmIndClearA T1 Network (DS-1) Alarm Indication condition has cleared. TRAP-TYPE .1.3.6.1.4.1.335.0.149 |
mcmAlarmT1LocalAlarmIndA T1 Local (DSX-1) Alarm Indication is generated with the
detection of the Out-of-Frame condition and when all 1's
are detected on the line. The Alarm Indication Signal (AIS)
is generated by the T1 module when the Internal Digital
Loopback test is invoked. TRAP-TYPE .1.3.6.1.4.1.335.0.150 |
mcmAlarmT1LocalAlarmIndClearA T1 Local (DSX-1) Alarm Indication condition has cleared. TRAP-TYPE .1.3.6.1.4.1.335.0.151 |
mcmAlarmCheckConfigurationThe configuration data was not written to the FLASH DRAM,
following a reset. TRAP-TYPE .1.3.6.1.4.1.335.0.152 |
mcmAlarmE1L2RedAlarmAn Out-of-Frame condition has persisted for 100 milliseconds
on L2. This results from a loss of signal, or loss of frame
synchronization. TRAP-TYPE .1.3.6.1.4.1.335.0.153 |
mcmAlarmE1L2RedAlarmClearThe condition causing the E1 L2 Red Alarm has been cleared. TRAP-TYPE .1.3.6.1.4.1.335.0.154 |
mcmAlarmE1L1RedAlarmAn Out-of-Frame condition has persisted for 100 milliseconds
on L1. This results from a loss of signal, or loss of frame
synchronization. TRAP-TYPE .1.3.6.1.4.1.335.0.155 |
mcmAlarmE1L1RedAlarmClearThe condition causing the E1 L1 Red Alarm has been cleared. TRAP-TYPE .1.3.6.1.4.1.335.0.156 |
mcmAlarmE1L2AlarmIndicationAn Alarm Indication Signal (AIS) occurred on L2. This
signal occurs when an Out-of-Frame and a pattern of all
ones is detected on L2, and persists for 100 milliseconds.
(AIS is generated when a defined condition is required to
be transmitted on the E1 line. Ex.: during loopbacks.) TRAP-TYPE .1.3.6.1.4.1.335.0.157 |
mcmAlarmE1L2AlarmIndicationClearThe E1 L2 Alarm Indication condition has cleared. TRAP-TYPE .1.3.6.1.4.1.335.0.158 |
mcmAlarmE1L1AlarmIndicationAn Alarm Indication Signal (AIS) occurred on L1. This
signal occurs when an Out-of-Frame and a pattern of all
ones is detected on L1, and persists for 100 milliseconds.
(AIS is generated when a defined condition is required to
be transmitted on the E1 line. Ex.: during loopbacks.) TRAP-TYPE .1.3.6.1.4.1.335.0.159 |
mcmAlarmE1L1AlarmIndicationClearThe E1 L1 Alarm Indication condition has cleared. TRAP-TYPE .1.3.6.1.4.1.335.0.160 |
mcmAlarmE1L2OOCASFrameAn Out of CAS Frame condition occurred on the Line 2 (L2)
interface. A Multiframe Alignment Signaling Loss indicates
that the CAS signaling is no longer in sync, This can be
caused by a loss of framing, defective hardware, or improper
generation of signaling information on time slot 16. The
EAM will set the 'Y' bit in time slot 16 of frame 0. TRAP-TYPE .1.3.6.1.4.1.335.0.161 |
mcmAlarmE1L2OOCASFrameClearThe E1 L2 Out of CAS Frame condition has cleared. TRAP-TYPE .1.3.6.1.4.1.335.0.162 |
mcmAlarmE1L1OOCASFrameAn Out of CAS Frame condition occurred on the Line 1 (L1)
interface. A Multiframe Alignment Signaling Loss indicates
that the CAS signaling is no longer in sync, This can be
caused by a loss of framing, defective hardware, or improper
generation of signaling information on time slot 16. The
EAM will set the 'Y' bit in time slot 16 of frame 0. TRAP-TYPE .1.3.6.1.4.1.335.0.163 |
mcmAlarmE1L1OOCASFrameClearThe E1 L1 Out of CAS Frame condition has cleared. TRAP-TYPE .1.3.6.1.4.1.335.0.164 |
mcmAlarmE1L2TS16AISAlarmA Time Slot 16 (TS16) Alarm Indication Signal occurred on
the Line 2 (L2) interface. A byte containing all ones was
received in Time Slot 16 for two consecutive frames during
an Out of Signaling Multiframe Alignment. TRAP-TYPE .1.3.6.1.4.1.335.0.165 |
mcmAlarmE1L2TS16AISAlarmClearThe E1 Time Slot 16 Alarm Indication Signal condition on
L2 has cleared. TRAP-TYPE .1.3.6.1.4.1.335.0.166 |
mcmAlarmE1L1TS16AISAlarmA Time Slot 16 (TS16) Alarm Indication Signal occurred on
the Line 1 (L1) interface. A byte containing all ones was
received in Time Slot 16 for two consecutive frames during
an Out of Signaling Multiframe Alignment. TRAP-TYPE .1.3.6.1.4.1.335.0.167 |
mcmAlarmE1L1TS16AISAlarmClearThe E1 Time Slot 16 Alarm Indication Signal condition on
L1 has cleared. TRAP-TYPE .1.3.6.1.4.1.335.0.168 |
mcmAlarmE1L2RemoteYAlarmA Remote 'Y' Signaling Alarm condition has occurred on
the Line 2 (L2) interface. This is the result of the
EAM setting the 'Y' bit in time slot 16 of frame 0. The
condition indicates the loss of signaling at the remote
site. TRAP-TYPE .1.3.6.1.4.1.335.0.169 |
mcmAlarmE1L2RemoteYAlarmClearThe E1 Remote 'Y' Signaling Alarm condition on the L2
interface has cleared. TRAP-TYPE .1.3.6.1.4.1.335.0.170 |
mcmAlarmE1L1RemoteYAlarmA Remote 'Y' Signaling Alarm condition has occurred on
the Line 1 (L1) interface. This is the result of the
EAM setting the 'Y' bit in time slot 16 of frame 0. The
condition indicates the loss of signaling at the remote
site. TRAP-TYPE .1.3.6.1.4.1.335.0.171 |
mcmAlarmE1L1RemoteYAlarmClearThe E1 Remote 'Y' Signaling Alarm condition on the L1
interface has cleared. TRAP-TYPE .1.3.6.1.4.1.335.0.172 |
mcmAlarmE1L2RemoteAAlarmA Remote 'A' Signaling Alarm condition has occurred on
the Line 2 (L2) interface. This Frame Alignment Signaling
condition occurs when the 'A' bit, received in Bit 3 of
Time Slot 0 of the Non Frame Alignment Signal (NFAS), is
detected. The alarm indicates that the receiver at the
remote is not detecting valid information; which could
be the result of a loss of signal, loss of frame
synchronization, or high-bit errors. TRAP-TYPE .1.3.6.1.4.1.335.0.173 |
mcmAlarmE1L2RemoteAAlarmClearThe E1 Remote 'A' Signaling Alarm condition on the L2
interface has cleared. TRAP-TYPE .1.3.6.1.4.1.335.0.174 |
mcmAlarmE1L1RemoteAAlarmA Remote 'A' Signaling Alarm condition has occurred on
the Line 1 (L1) interface. This Frame Alignment Signaling
condition occurs when the 'A' bit, received in Bit 3 of
Time Slot 0 of the Non Frame Alignment Signal (NFAS), is
detected. The alarm indicates that the receiver at the
remote is not detecting valid information; which could
be the result of a loss of signal, loss of frame
synchronization, or high-bit errors. TRAP-TYPE .1.3.6.1.4.1.335.0.175 |
mcmAlarmE1L1RemoteAAlarmClearThe E1 Remote 'A' Signaling Alarm condition on the L1
interface has cleared. TRAP-TYPE .1.3.6.1.4.1.335.0.176 |
mcmProxyAlarmNodeUnreachableThe proxy agent's event polling application could not reach
the intended node. TRAP-TYPE .1.3.6.1.4.1.335.0.500 |
mcmProxyEventPollingBeginThe proxy agent has begun polling for events at the
specified time. TRAP-TYPE .1.3.6.1.4.1.335.0.600 |
mcmProxyEventPollingEndThe proxy agent has completed the event poll cycle. TRAP-TYPE .1.3.6.1.4.1.335.0.601 |
products OBJECT IDENTIFIER .1.3.6.1.4.1.335.1 |
marathon-netrunner OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.1 |
micom-proxy OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2 |
marathon-netrunner-proxy OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1 |
security OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.1 |
lcdSecurityPasswordAccess password to the LCD/Keypad located on front of
the integration unit.rw DisplayString .1.3.6.1.4.1.335.1.2.1.1.1 |
cmdPortSecurityGroup OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.1.2 |
cmdPortSecurityGlobalPasswordAccess password to all functions. Password must be
alphanumeric characters (A-Z, 0-9) up to 8 characters.rw DisplayString .1.3.6.1.4.1.335.1.2.1.1.2.1 |
cmdPortSecurityStatusPasswordAccess password to view, status, and exit Command
Facility functions. Password must be alphanumeric
characters (A-Z, 0-9) up to 8 characters.rw DisplayString .1.3.6.1.4.1.335.1.2.1.1.2.2 |
nmsSecurityPPPPasswordAccess password to the $PPP Facility. Password must be
alphanumeric characters (A-Z, 0-9) upto 8 characters.rw DisplayString .1.3.6.1.4.1.335.1.2.1.1.3 |
diagnostics OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.2 |
pingResponseDetermines whether or not the node is reachable.ro Enumeration .1.3.6.1.4.1.335.1.2.1.2.1 |
voiceChannelDiagTableThis table provides the system diagnostics function to test the
voice/fax module(s) if installed. SEQUENCE OF VoiceChannelDiagEntry .1.3.6.1.4.1.335.1.2.1.2.2 |
voiceChannelDiagEntryAn entry within the table specifying particular channel on voice module. VoiceChannelDiagEntry .1.3.6.1.4.1.335.1.2.1.2.2.1 |
voiceChannelDiagCardNumberIdentifies the module/card number for the specified channel
to be tested.ro INTEGER .1.3.6.1.4.1.335.1.2.1.2.2.1.1 |
voiceChannelDiagChannelNumberIdentifies the channel number to which this entry pertains.ro INTEGER .1.3.6.1.4.1.335.1.2.1.2.2.1.2 |
voiceChannelDiagCommandOptions to initiate different type of tests or to terminate the tests.
Option 2 allows monitoring of the level of the input voice signal. Option
3 verifies that the voice channel is working properly. Option 4 causes
the voice channel to compress the local speech signal and then to pass
this signal through the reconstruction process back to the local receiver.rw Enumeration .1.3.6.1.4.1.335.1.2.1.2.2.1.3 |
syncChannelDiagTableTable to control the testing and diagnosing of specific
sync channel. SEQUENCE OF SyncChannelDiagEntry .1.3.6.1.4.1.335.1.2.1.2.3 |
syncChannelDiagEntryEntry into the diagnostic table for a specific channel on
specified module. SyncChannelDiagEntry .1.3.6.1.4.1.335.1.2.1.2.3.1 |
syncChannelDiagCardNumberThe specified module/card number of the channel to be tested.ro INTEGER .1.3.6.1.4.1.335.1.2.1.2.3.1.1 |
syncChannelDiagChannelNumberThe specified channel number to be tested.ro INTEGER .1.3.6.1.4.1.335.1.2.1.2.3.1.2 |
syncChannelDiagCommandCommand option to terminate and initiate the test. The test
loops the control signals and data back.rw Enumeration .1.3.6.1.4.1.335.1.2.1.2.3.1.3 |
configuration OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3 |
system OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.1 |
attributes OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.1.1 |
sysPromIDIdentifies the unique PROM identifier.ro DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.1.1 |
sysTypeGroup OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.1.1.2 |
sysSoftwareTypeIdentifies the software base type running on the Integration unit.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.1.1.2.1 |
sysHardwareTypeIdentifies the type of CCM module present in the Integration unit.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.1.1.2.2 |
sysOperationalTypeIdentifies the operational type of the Integration unit as node
or feeder.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.1.1.2.3 |
sysSoftwarePhaseIdentifies the revision of the operating software running on
the node.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.1.1.2.4 |
sysFeatureTypeIdentifies the type of the feature pack installed on the unit.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.1.1.2.5 |
sysFeatureRTCIdentifies whether or not the real time clock is present on the unit.
Note that NMS modules are available with RTC.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.1.1.2.6 |
sysLocNodeLinkTableTable containing MB-Feeder connection information. SEQUENCE OF SysLocNodeLinkEntry .1.3.6.1.4.1.335.1.2.1.3.1.1.3 |
sysLocNodeLinkEntryEntry within the table identifying the name, type, and number
of connected MB-Feeder (if any). SysLocNodeLinkEntry .1.3.6.1.4.1.335.1.2.1.3.1.1.3.1 |
sysLocNodeLinkIndexInstances into the table for each (1-6) link entry.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.1.1.3.1.1 |
sysLocNodeLinkNodeNameOfFeederIndicates the name of the connected (if any) feeder to a
particular port.ro DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.1.3.1.2 |
sysLocNodeLinkNodeTypeIdentifies whether or not the MB-Feeder is connected to
a particular port.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.1.1.3.1.3 |
sysLocNodeLinkNodeNumberIndicates the number of the connected (if any) feeder to a
particular port. A value of zero represent that the feeder is
not present.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.1.1.3.1.4 |
sysDateTimeSets the current date and the time on the unit. Format (byte
sequence) is Month, Day, Hour, Minutes, Seconds, Day of Week, Year.rw OCTET STRING .1.3.6.1.4.1.335.1.2.1.3.1.1.4 |
sysClassCfgTableTable to configure a class. Class is defined as a port or grouping
of ports dedicated to a specific application or location. SEQUENCE OF SysClassCfgEntry .1.3.6.1.4.1.335.1.2.1.3.1.1.5 |
sysClassCfgEntryAn entry into the table for a specific class number. SysClassCfgEntry .1.3.6.1.4.1.335.1.2.1.3.1.1.5.1 |
sysClassCfgClassNumberThe available class to be configured numbered from 1 to 64.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.1.1.5.1.1 |
sysClassCfgClassNameAssigns a class name to a selected class number. Class name
can be up to eight characters long and may use characters A-Z,
0-9, and _.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.1.5.1.2 |
sysClassCfgClassSecondaryThe designated secondary class to the specified class used to
automatically route connections to this class if the primary
class channels are busy.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.1.1.5.1.3 |
sysClassCfgClassMessageDisplays (on command facility) when the user connects to
a port within the class.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.1.5.1.4 |
sysClassCfgClassPasswordProtects the access to a particular class. The default is no
password (NULL Password).rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.1.5.1.5 |
sysClassCfgNoActivityTimeOutThe no activity feature monitors the class channel. After a
specified period of time, if there is no activity on the channel, it
will be disconnected. Value 0 = disabled; values 1-255 = the timeout
interval in minutes.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.1.1.5.1.6 |
sysClassCfgEntryStatusObject to create conceptual row entry in the table. Internally used
to cache all the column objects till the commit is done through active(1).
Option 6 (destroy) deletes the entry (class) from the configured classes.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.1.1.5.1.7 |
sysAccessNodeNameThis is the name of the node which has been selected as the
access point for the MICOMVision Manager in the Network.
Configuring this object for a node results in the MICOM Alarms
being forwarded to this specified Access node and the NMS system
being informed of pending alarms awaiting retrieval.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.1.6 |
sysFlashDownloadGroup OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.1.1.7 |
sysFlashDownloadPasswordConfigures the security password for the download facility.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.1.7.1 |
sysFlashDownloadUseFileConfigures which Flash Bank that will be loaded from when the
marathon is reset to re-load from flash.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.1.1.7.2 |
sysFlashDownloadDataActivityTimeoutConfigures the Data Activity Timeout to be used while downloading
an image to Flash Memory. The range is 30 - 240 seconds.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.1.1.7.3 |
sysMeshRoutingConfigures whether mesh routing is enabled for this Integration unit.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.1.1.8 |
sysBootIDIndicates the boot identifier if boot prom is present.ro DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.1.9 |
sysNetTimeThe date and time to be configured on all the Integration units
on the network. Format (byte sequence) is Month, Day, Hour, Minutes,
Seconds, Day of Week, Year.rw OCTET STRING .1.3.6.1.4.1.335.1.2.1.3.1.1.10 |
sysCodeDownloadGroup OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.1.1.11 |
sysCodeDownloadTypeIdentifies the type of Code Download that is to be performed.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.1.1.11.1 |
sysCodeDownloadNodeNameThe name of the node to which software is to be downloaded.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.1.11.2 |
sysCodeDownloadSlotNumberThe slot number of the module to which software is to be downloaded.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.1.1.11.3 |
sysCodeDownloadChannelNumberThe Voice Channel number to which software is to be downloaded.
Only valid for Voice.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.1.1.11.4 |
sysCodeDownloadImageFileThe name of the code image file to be downloaded.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.1.11.5 |
sysCodeDownloadFlashBankThe destination flash bank to be downloaded.
Only for CCM download.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.1.1.11.6 |
sysCodeDownloadRestartFromBankIdentifies the subsequent flash bank to be started from.
Only for CCM download.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.1.1.11.7 |
sysCodeDownloadResetValue of 1 identifies that the reset of the module/node
is required after successful download.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.1.1.11.8 |
sysCodeDownloadActionStatusOption 0 initiates a request for the code download. The status
of the process is conveyed via options 1 through n.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.1.1.11.9 |
sysCodeDownloadFileSizeThis is the Total Number of Bytes in the image file that is being
downloaded. Valid only after a download has started.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.1.1.11.10 |
sysCodeDownloadBytesDownloadedThis is the Total Number of Bytes that have been sent to the Integration
unit. Upon completion, this should equal the sysCodeDownloadFileSize
paramater. Valid only after a download has been started.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.1.1.11.11 |
sysCodeDownloadNodeNumberThe numeric value (Node ID #) that represents this node in the network.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.1.1.11.12 |
messages OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.1.2 |
sysMessageWelcomeDisplays when the user first successfully connects to the Integration unit.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.2.1 |
sysMessageChannelPasswdPrompts the user for the password associated for the sign-on
channel. This is the first dialog message that appears when the
user attempts to connect to the network from the command
line facility.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.2.2 |
sysMessageClassRequestPrompts (at the command facility line) the async channel
user for the destination class or channel.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.2.3 |
sysMessageConnectedDisplays (on the command facility line) when a connection
to any resource (class or matrix switch) has been established
across an interconnect link .rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.2.4 |
sysMessageQueuedDisplays (on the command facility line) when a user is waiting
far a channel in wait queue.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.2.5 |
sysMessageDisconnectedDisplays (on the command facility line) when the connection
has been broken. It is only sent to the call originator using
switching (This is not for force connections).rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.2.6 |
sysMessageCallInProgressDisplays (on the command facility line) while the call is in
process of being connected.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.2.7 |
sysMessageNoAnswerDisplays (on the command facility line) when there is no
answer from the destination port.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.2.8 |
sysMessageUnassignedDisplays (on the command facility line) when a node, class
or channel is unknown in the network.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.2.9 |
sysMessageUnavailableDisplays (on the command facility line) when a user request
a resource which exists, but is not in service (operational).rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.2.10 |
sysMessageBusyDisplays (on the command facility line) only to the user using
matrix switching when the requested resource is in use.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.2.11 |
sysMessageIncompatibleDisplays (on the command facility line) for any attempted
connection that is not compatible with the configuration.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.2.12 |
sysMessageClassPasswdPrompts (on the command facility line) for the password
of the requested class.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.2.13 |
sysMessageLCDKeypadBannerDisplays the banner string on the LCD keypad.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.1.2.14 |
card OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.2 |
cardTableTable to view the hardware configuration of the Integration unit. SEQUENCE OF CardEntry .1.3.6.1.4.1.335.1.2.1.3.2.1 |
cardEntryEntry pertaining to the present module(s). CardEntry .1.3.6.1.4.1.335.1.2.1.3.2.1.1 |
cardSlotNumberIdentifies the location of the module within the unit.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.2.1.1.1 |
cardModuleIDIdentifies the part number of the module in the specific location.
0FFFFh if no NMS card installed, 03ffh if no card installed.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.2.1.1.2 |
cardPcbRevisionIdentifies the revision level of the module. 0ffh if no NMS card
installed, 03Fh if no card installed.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.2.1.1.3 |
numberOfCardsThe total number of cards installed in the Integration unit.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.2.2 |
eliCardFunctionTableTable containing the functionality on resident eli cards (if any). SEQUENCE OF EliCardFunctionEntry .1.3.6.1.4.1.335.1.2.1.3.2.3 |
eliCardFunctionEntryEntry within the table to specify a particular slot where an eli
card is located. EliCardFunctionEntry .1.3.6.1.4.1.335.1.2.1.3.2.3.1 |
eliCardFunctionSlotNumberThe slot number of the eli card.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.2.3.1.1 |
eliCardFunctionPromIDThe prom part number of the software that is installed and
running on the eli card.ro DisplayString .1.3.6.1.4.1.335.1.2.1.3.2.3.1.2 |
eliCardFunctionTypeRTSFunctionIdentifies whether this eli card performs the function of
an RTS or not.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.2.3.1.3 |
eliCardFunctionTypeBridgeFunctionIdentifies whether this eli card performs the function of
a bridge or not.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.2.3.1.4 |
eliCardFunctionTypeRouterFunctionIdentifies whether this eli card performs the function of
a router or not.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.2.3.1.5 |
eliCardFunctionFlashMemoryIdentifies whether this eli card contains flash memory or not.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.2.3.1.6 |
t1e1CardSoftwareInfoTableTable describing the software on resident (if any) T1 or E1 card. SEQUENCE OF T1e1CardSoftwareInfoEntry .1.3.6.1.4.1.335.1.2.1.3.2.4 |
t1e1CardSoftwareInfoEntryEntry within the table to specify a particular T1 or E1 card. T1e1CardSoftwareInfoEntry .1.3.6.1.4.1.335.1.2.1.3.2.4.1 |
t1e1CardSoftwareInfoCardNumberDisplays the Card number of the T1 or E1 module.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.2.4.1.1 |
t1e1CardSoftwareInfoCardTypeDisplays the access module type; T1 or E1.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.2.4.1.2 |
t1e1CardSoftwareInfoReleaseLevelDisplays which Software release is installed on the T1/E1 card.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.2.4.1.3 |
t1e1CardSoftwareInfoSoftwareIDDisplays which Software part number is installed on the T1/E1 card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.335.1.2.1.3.2.4.1.4 |
t1e1CardSoftwareInfoBootCodeDisplays which boot prom part number is installed on the T1/E1 card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.335.1.2.1.3.2.4.1.5 |
port OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.3 |
portCfgTableTable to establish the type of port connection to be assigned to
the selected port. SEQUENCE OF PortCfgEntry .1.3.6.1.4.1.335.1.2.1.3.3.1 |
portCfgEntryEntry into the table for the selected port. PortCfgEntry .1.3.6.1.4.1.335.1.2.1.3.3.1.1 |
portCfgCardNumberIndicates the card/module of the channel to be configured.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.3.1.1.1 |
portCfgChannelNumberIndicates the channel/port number to be configured.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.3.1.1.2 |
portCfgChannelTypeAssigns the type of connection to the selected port.
Note: A node reset is required after setting the port
configuration. Also note that if a channel is currently
connected, forced or switch connected, the channel must first
be disconnected. The procedure to do this would be to place
the channel out of service (chControlCommand disable(2)), then
disconnect (chControlCommand forceDIsconnect(4)) the channel.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.3.1.1.3 |
syncPortCfgTableTable to configure the protocol for the specified sync channel. SEQUENCE OF SyncPortCfgEntry .1.3.6.1.4.1.335.1.2.1.3.3.2 |
syncPortCfgEntryEntry into the table specifying a particular channel on a particular
module/card. SyncPortCfgEntry .1.3.6.1.4.1.335.1.2.1.3.3.2.1 |
syncPortCfgCardNumberIdentifies the card/module of the sync channel to be configured.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.3.2.1.1 |
syncPortCfgChannelNumberIndicates the sync channel number to be configured.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.3.2.1.2 |
syncPortCfgProtocolAssigns the sync protocol to the selected port. Note: A node reset is
required after the protocol is configured.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.3.2.1.3 |
fCmdPortPhyParaTableTable of configurations for the physical parameters of the
fixed command port on an NMS module. SEQUENCE OF FCmdPortPhyParaEntry .1.3.6.1.4.1.335.1.2.1.3.3.3 |
fCmdPortPhyParaEntryEntry within the table to specify the fixed command port
channel number (2) on an NMS module/card (6). FCmdPortPhyParaEntry .1.3.6.1.4.1.335.1.2.1.3.3.3.1 |
fCmdPortPhyParaCardNumberThe card number (=6) of the NMS module containing the fixed cmd port.ro INTEGER (6) .1.3.6.1.4.1.335.1.2.1.3.3.3.1.1 |
fCmdPortPhyParaChannelNumberThe channel number (=2) of the fixed cmd port on the NMS module.ro INTEGER (2) .1.3.6.1.4.1.335.1.2.1.3.3.3.1.2 |
fCmdPortPhyParaStopBitsSets the number of stop-bits inserted at the end of a character.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.3.3.1.3 |
fCmdPortPhyParaCodeLevelSets the number of data bits per character. This includes the
parity bit.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.3.3.1.4 |
fCmdPortPhyParaDataRateSets the data rate in bits per seconds of the fixed command port.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.3.3.1.5 |
fCmdPortPhyParaEchoDetermines whether the Integration unit should echo input from the terminal
or not.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.3.3.1.6 |
fCmdPortPhyParaCRDelayConfigures the number of character delays that should be introduced
after each CR (carriage return).rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.3.3.1.7 |
fCmdPortPhyParaLFDelayConfigures the number of character delays that should be introduced
after each LF (line feed).rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.3.3.1.8 |
fCmdPortPhyParaFFDelayConfigures the number of chanacter delays that should be introduced
afer each FF (form feed).rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.3.3.1.9 |
fCmdPortPhyParaParitySets the message and data parity.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.3.3.1.10 |
logPortPhyParaTableTable to configure the log port (present on NMS module)
parameters. SEQUENCE OF LogPortPhyParaEntry .1.3.6.1.4.1.335.1.2.1.3.3.4 |
logPortPhyParaEntryEntry within the table to specify the log port
channel number (1) on an NMS module/card (6). LogPortPhyParaEntry .1.3.6.1.4.1.335.1.2.1.3.3.4.1 |
logPortPhyParaCardNumberThe card number (=6) of the NMS Module that contains the log port.ro INTEGER (6) .1.3.6.1.4.1.335.1.2.1.3.3.4.1.1 |
logPortPhyParaChannelNumberThe channel number of the log port (=1).ro INTEGER (1) .1.3.6.1.4.1.335.1.2.1.3.3.4.1.2 |
logPortPhyParaStopBitsConfigures the number of stop bits that the Integration unit should
generate and check for on this channel.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.3.4.1.3 |
logPortPhyParaCodeLevelSets the number of data bits per character. This includes the
parity bit.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.3.4.1.4 |
logPortPhyParaDataRateSets the data rate in bits per seconds of the log port.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.3.4.1.5 |
logPortPhyParaCRDelayConfigures the number of Character Delays required to be
inserted after each CR (carriage return).rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.3.4.1.6 |
logPortPhyParaLFDelayConfigures the number of Character Delays required to be
inserted after each LF (Line Feed).rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.3.4.1.7 |
logPortPhyParaFFDelayConfigures the number of Character Delays required to be
inserted after each FF (form feed).rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.3.4.1.8 |
logPortPhyParaXONCharConfigures which character the Integration unit should check for
and respond to for stopping data flow on a channel.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.3.4.1.9 |
logPortPhyParaXOFFCharConfigures which character the Marathon should check for
and respond to for re-starting data flow on a channel.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.3.4.1.10 |
logPortPhyParaFlowControlConfigures which type of flow control should be used
for the log port.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.3.4.1.11 |
logPortPhyParaBufferControlConfigures what type of buffer control to be used
in the communications with the log port.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.3.4.1.12 |
logPortPhyParaParityConfigures what type of parity to use with the log port.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.3.4.1.13 |
commandPortExtModemNumberModem phone number to call to send ASCII events out.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.3.5 |
commandPortDataActivityTimeoutConfigures the command facility port inactivity timeout (minutes).rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.3.6 |
syncPortPreConfigTableTable to configure a sync channel protocol prior to configuring
a port as a sync channel. By using this table to 'preset' the sync
protocol, only 1 node reset is needed following the sync channel
assignment to complete the configuration. SEQUENCE OF SyncPortPreConfigEntry .1.3.6.1.4.1.335.1.2.1.3.3.7 |
syncPortPreConfigEntryEntry within the table to specify a particular sync channel for
pre-configuration on a specific module/card. SyncPortPreConfigEntry .1.3.6.1.4.1.335.1.2.1.3.3.7.1 |
syncPortPreConfigCardNumberIdentifies the module/card for sync channel pre-configuration.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.3.7.1.1 |
syncPortPreConfigChannelNumberIdentifies the port number for sync channel pre-configuration.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.3.7.1.2 |
syncPortPreConfigProtocolThe protocol to be used for pre-configuring a sync channel.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.3.7.1.3 |
channel OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.4 |
sync-channel OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.4.1 |
syncChPhyParaTableFor the configuration of synchronous channels, this table controls
and modifies the operating parameters for the port. SEQUENCE OF SyncChPhyParaEntry .1.3.6.1.4.1.335.1.2.1.3.4.1.1 |
syncChPhyParaEntryEntry into the table pertaining to a specific sync channel on a
specific module. SyncChPhyParaEntry .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1 |
syncChPhyParaCardNumberThe card/module number of the channel this entry pertains to.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.1 |
syncChPhyParaChannelNumberThe channel number on a specified module this configuration
entry pertains to.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.2 |
syncChPhyParaDataRateSets data rate in bits per second for the user sync channel. Default
is 2400.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.3 |
syncChPhyParaCarrierModeDefines when carrier is held high, either constant or variable.
This parameter is configurable for all Sync protocols EXCEPT tdm(10)
and fastPacket(9). For Sync protocol, rtsCts(5), the parameter
default is Option 'variable(1)'. For Sync protocols - dlcChannel(1),
asciiBisync(2), ebcdicBisync(3), hpSync(4), syncPad(6), micomDlc(7),
and micomVoice(8); the parameter default is Option 'constant(2)'.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.4 |
syncChPhyParaInterfaceTypeSets the user channel for toDTE to interface with data terminal
equipment; and toDCE to interface with data communication equipment
such as a tail-circuit modem. This parameter is configurable for all
Sync protocols EXCEPT fastPacket(9).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.5 |
syncChPhyParaIdleFillSelects what the Integration unit will output when the line
is idle. This parameter is configurable ONLY for Sync protocol
dlcChannel(1).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.6 |
syncChPhyParaHighSyncCharSets the value (high byte) of the leading sync character for
the start of the block. This parameter is configurable ONLY for
Sync protocol syncPad(6).rw OCTET STRING .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.7 |
syncChPhyParaLowSyncCharSets the value (low byte) of the leading sync character for
the start of the block. This parameter is configurable for all
Sync protocols EXCEPT dlcChannel(1), micomDlc(7), and micomVoice(8).rw OCTET STRING .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.8 |
syncChPhyParaNumLeadSyncCountSets the number of leading sync characters that the Integration
unit will generate on the output (0-9). This will allow the device
on the selected channel to synchronize. Enter zero to specify
all leading syncs as transparent. They will not be stripped out.
This parameter is ONLY configurable for Sync protocols asciiBisync(2),
ebcdicBisync(3), hpSync(4), rtsCts(5), and syncPad(6),rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.9 |
syncChPhyParaMaxTxBlockSizeSets the block size in bytes of the data to the Integration
unit from the attached device. This parameter is configurable
for all Sync protocols EXCEPT micomDlc(7), fastPacket(9), and
tdm(10).
For Sync protocol hpSync(4), the parameter default is 9876. For
Sync protocol micomVoice(8), the parameter default is 1024. For
Sync protocols dlcChannel(1), asciiBisync(2), ebcdicBisync(3),
rtsCts(5), and syncPad(6); the parameter default is 512.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.10 |
syncChPhyParaPadCharSets the value of pad character (alpha numeric). It precedes the
sync character and follows the end of the block. It is used to pad
the block. This parameter is ONLY configurable for the Sync protocols
asciiBisync(2), ebcdicBisync(3), hpSync(4), rtsCts(5), and syncPad(6).rw OCTET STRING .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.11 |
syncChPhyParaNumLeadingPadsSets the number of leading pad characters to be transmitted at
the start of the block for a time delay (1-9). This parameter is
ONLY configurable for the Sync protocols asciiBisync(2), ebcdicBisync(3),
hpSync(4), rtsCts(5), and syncPad(6).
For Sync protocols asciiBisync(2), ebcdicBisync(3), and hpSync(4) the
parameter default is 1. For Sync protocol rtsCts(5) the default is
3. For Sync protocol syncPad(6) the default is 2.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.12 |
syncChPhyParaNumTrailingPadsSets the number of trailing pad characters to be transmitted at
the end of the block. This parameter is ONLY configurable for the
Sync protocols asciiBisync(2), ebcdicBisync(3), hpSync(4), rtsCts(5),
and syncPad(6).
For Sync protocols asciiBisync(2), ebcdicBisync(3), hpSync(4), and
syncPad(6) the parameter default is 2. For Sync protocol rtsCts(5)
the default is 3.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.13 |
syncChPhyParaClockFlowControlSelects whether or not the local sync channel will be flow
controlled. This parameter is configurable for all Sync protocols
EXCEPT fastPacket(9), and tdm(10).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.14 |
syncChPhyParaEncodingSelects one of the two types of encoding, NRZ or NRZI,
depending on the attached device. This parameter is ONLY
configurable for Sync protocol dlcChannel(1).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.15 |
syncChPhyParaChTxClockingSets the channel's source for transmit clock. This
parameter, combined with the syncChPhyParaChRxClocking
parameter, corresponds to the Channel Clocking parameter
which is displayed in the Sync channel configuration menu
of the unit's $CMD facility. This parameter is configurable
for all Sync protocols EXCEPT fastPacket(9).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.16 |
syncChPhyParaChRxClockingSets the channel's source for receive clock. This
parameter, combined with the syncChPhyParaChTxClocking
parameter, corresponds to the Channel Clocking parameter
which is displayed in the Sync channel configuration menu
of the unit's $CMD facility. This parameter is configurable
for all Sync protocols EXCEPT fastPacket(9).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.17 |
syncChPhyParaPrioritySelects the priority of the port, high or low. This parameter
is configurable for all Sync protocols EXCEPT tdm(10).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.18 |
syncChPhyParaDSRControlSelects whether the remote DTR changes appear on the
local DSR or are ignored.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.19 |
syncChPhyParaBufferControlUsed to regulate data transmission from a device attached
to user channel. This parameter is configurable for all Sync
protocols EXCEPT fastPacket(9) and tdm(10).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.20 |
syncChPhyParaMaxRxBlockSizeSets the block size in bytes of the data to attached device
from the Integration unit. This parameter is configurable for
all Sync protocols EXCEPT micomDlc(7), fastPacket(9), and tdm(10).
For Sync protocol hpSync(4), the parameter default is 9876. For
Sync protocol micomVoice(8), the parameter default is 1024. For
Sync protocols dlcChannel(1), asciiBisync(2), ebcdicBisync(3),
rtsCts(5), and syncPad(6); the parameter default is 512.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.21 |
syncChPhyParaProtocolSets the sync channel protocol.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.22 |
syncChPhyParaClaimedBandwidthSets the claimed bandwidth of the sync channel. This
is the amount of bandwidth that should be reserved on a link
for this channel / 10. -ie- If you want to reserve 9600 bps
for this channel you should set this to 960. This parameter
is configurable for all Sync protocols EXCEPT tdm(10).rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.23 |
syncChPhyParaDLCTransitRateSets the transit rate of the sync channel. This parameter
is ONLY configurable for the Sync protocol dlcChannel(1).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.1.1.1.24 |
async-channel OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.4.2 |
asyncChPhyParaTableFor the configuration of asynchronous channels, this table controls
and modifies the operating parameters for the port. SEQUENCE OF AsyncChPhyParaEntry .1.3.6.1.4.1.335.1.2.1.3.4.2.1 |
asyncChPhyParaEntryEntry into the table pertaining to a specific channel on a specific module. AsyncChPhyParaEntry .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1 |
asyncChPhyParaCardNumberThe module/card number containing the async channel to which
the entry pertains to.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.1 |
asyncChPhyParaChannelNumberThe async channel number to which the entry pertains to.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.2 |
asyncChPhyParaStopBitsSets the number of stop-bits inserted at the end of a character.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.3 |
asyncChPhyParaCodeLevelSets the number of data bits per character. This includes the
parity bit.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.4 |
asyncChPhyParaDataRateSets the data rate in bits per seconds of the async user channel.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.5 |
asyncChPhyParaEchoTurns the echo function on or off when the terminal(2) option
is selected for the asyncChPhyParaConnectTo object.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.6 |
asyncChPhyParaHPXModeSould be set to ON only when Hewlett Packerd HP-3000 view
systems using type 26XX display stations (operating under
term type 10) are connected to the port being configured.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.7 |
asyncChPhyParaConnectToSets the type of equipment which is connected to the
port, a host or terminal (also printer).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.8 |
asyncChPhyParaRemCTSControlDetermines whether remote CTS signal is strapped or transparent.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.9 |
asyncChPhyParaCRDelaySets the delay in character times to allow for mechanical
action to take place when a carriage return control character
is transmitted to a channel.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.10 |
asyncChPhyParaLFDelaySets the delay in character times to allow for mechanical
action to take place when a line feed control character is
transmitted to a channel.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.11 |
asyncChPhyParaFFDelaySets the delay in character times to allow for mechanical
action to take place when a form feed control character is
transmitted to a channel.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.12 |
asyncChPhyParaXONCharDefines the different XON characters.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.13 |
asyncChPhyParaXOFFCharDefines the different XOFF characters.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.14 |
asyncChPhyParaCmdFacilityAccessPermits or denies (the port being configured) access to the
Command Facility Main Menu to view or change the system
operating parameters.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.15 |
asyncChPhyParaCmdModeEntrySelects the control character sequence to access to the
Command Mode.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.16 |
asyncChPhyParaLocChannelConfigControls the access to the Local Channel Configuration Menu.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.17 |
asyncChPhyParaCmdModeAccessPermits or deny (the port being configured) access to
the Command Mode.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.18 |
asyncChPhyParaTandemSupportShould set to ON only when Tandem Computers are connected
to the channel being configured.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.19 |
asyncChPhyParaSmoothScrollShould be set to ON only when DEC VT100 smooth scroll
terminals are connected to the system.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.20 |
asyncChPhyParaFlowControlAn attached device uses flow control to start or stop data
flow from the Integration unit. The attached device may control data
flow by use of XON/XOFF, DTR, XON/XOFF + DTR or a
special WANGX character.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.21 |
asyncChPhyParaBufferControlBuffer control to start or stop the data flow from the
attached device. The attached device may control data
flow by use of XON/XOFF, CTS, or a special WANGX
character.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.22 |
asyncChPhyParaFlowControlStripAllows the flow control characters to be passed through or
stripped from the Integration unit.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.23 |
asyncChPhyParaSyncLossDisconnectWhen enabled, the local node toggles the controls and
purges the data. This occurs when the link has experienced
a sync loss condition for more than 20 seconds.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.24 |
asyncChPhyParaEIAControlsAbility to recognize or ignore the EIA control signals from the
attached device.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.25 |
asyncChPhyParaPriorityDecides whether or not this channel is to receive a high
or low priority for use. A high priority channel will take
precedence over a channel with low priority.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.26 |
asyncChPhyParaParitySets the message and data parity for the Integration unit. Depending on the
asyncChPhyParaCodeLevel selection of 5-8 bits, the available parity
is space, odd, even, mark, and none. For code level 9 bits, the
available choice is odd or even.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.27 |
asyncChPhyParaCompressionWhen enabled, the unit compresses a block of data when transmitting.
Fewer bytes are required for the transfer thus increasing the data
transfer rate (making it faster).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.1.1.28 |
asyncChSwParaTableTable for configuration of async channel switching parameters. SEQUENCE OF AsyncChSwParaEntry .1.3.6.1.4.1.335.1.2.1.3.4.2.2 |
asyncChSwParaEntryEntry within the table to specify a particular async channel number
on a specific module/card. AsyncChSwParaEntry .1.3.6.1.4.1.335.1.2.1.3.4.2.2.1 |
asyncChSwParaCardNumberIdentifies the module/card number for the async channel specific
to the channel switching parameters.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.2.2.1.1 |
asyncChSwParaChannelNumberIdentifies the async channel specific to the channel switching parameters.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.2.2.1.2 |
asyncChSwParaDestinationClassAssign the destination class name to the async channel for class switching.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.4.2.2.1.3 |
asyncChSwParaConnectProtocolSelects the connect protocol for the port being configured. The
protocol must be compatible with the attached device.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.2.1.4 |
asyncChSwParaRcvInhibitControls the port being configured from receiving a connection
request.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.2.1.5 |
asyncChSwParaResourceClassNumberAssigns a resource class number (1 - 64) to the async channel.
Zero reflects no resource class assignment.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.2.2.1.6 |
asyncChSwParaCallInhibitControls the port being configured from making a connection
request.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.2.1.7 |
asyncChSwParaUnbalanceRatesControls the connections of ports which have dissimilar
baud rates (different speed).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.2.1.8 |
asyncChSwParaCharacterSetOption to select either an ASCII or non-ASCII character set.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.2.1.9 |
asyncChSwParaMatrixSwitchingThe ability of the port to make a connection request by
specifying a node/channel number.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.2.2.1.10 |
asyncChSwParaChannelPasswordA unique password attached to the port being configured
to control access for security.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.4.2.2.1.11 |
voice-fax-channel OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.4.3 |
voiceFaxChPhyParaTableTable for configuring the voice/Fax channel physical parameters. SEQUENCE OF VoiceFaxChPhyParaEntry .1.3.6.1.4.1.335.1.2.1.3.4.3.1 |
voiceFaxChPhyParaEntryEntry within the table to specify a particular voice/Fax channel number
on a specific module/card. VoiceFaxChPhyParaEntry .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1 |
voiceFaxChPhyParaCardNumberIdentifies the module/card number for the voice/Fax channel specific
to the channel's physical parameters.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.1 |
voiceFaxChPhyParaChannelNumberIdentifies the voice/Fax channel specific to the channel's
physical parameters.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.2 |
voiceFaxChPhyParaWireOperationSets the voice channel for either 2-wire or 4-wire analog
operation. Valid only when voiceFaxChPhyParaBergStrapType
indicates em(2) or enhancedEm(5).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.3 |
voiceFaxChPhyParaViewSignallingTypeIndicates the signalling type. This parameter is computed
from the strapping and signalling interface configuration.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.4 |
voiceFaxChPhyParaBergStrapTypeIndicates the Berg Hardware Strap configuration on the
voice/Fax channel.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.5 |
voiceFaxChPhyParaSuppressionDuring idle periods in which suppression is enabled (=0),
the sending voice channel DSP generates suppression service
frames containing a noise level estimate and no data. This
is sent to the receiving voice channel DSP which will either
regenerate the noise level or silence the output depending on
the configuration of voiceFaxChPhyParaBackground.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.6 |
voiceFaxChPhyParaCfgSignallingTypeConfigures where the ring signal is generated (locally or by
remote PBX equipment) and the ring cadence (timing of rings and
silence periods). This parameter is ONLY configurable for E&M,
Enhanced and Standard E&M, 3-Port Fax, and Enhanced and Standard
FXS voice modules. The following is a matrix of valid signaling
type options for each configurable voice module, given the Channel
Version value (voiceFaxChPhyParaChannelVersion) and Integration
Unit software release (sysSoftwarePhase).
Voice Module Configurable Options Chan Version Release
E&M emDC,em2280,emPulseDc 2 ALL
KTS repeated,interruptOR2by4, 2 ALL
interrupt1by2
Std/Enh E&M emDC,em2280,emPulseDC 2,3,5 ALL
emDC,em2280,emPulseDC, 6,7 Phase 5.1
emWink and Above
3-Port Fax repeated,interruptOR2by4 3,5-7 ALL
Std/Enh FXS repeated,interruptOR2by4, 2,3 ALL
interrupt1by2
repeated,interruptOR2by4 5-7 Phase 5.0
and Aboverw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.7 |
voiceFaxChPhyParaOPXNumberOfRingsFrom customer equipment, the number of rings generated
before hearing the voice/fax module dial tone of the local
Integration unit. This parameter is ONLY configurable for
the OPX, and Standard and Enhanced FXO voice modules.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.8 |
voiceFaxChPhyParaFXOSupervisorDiscConfigures the means to disconnect a telephone connection.
Either an absence of loop current (powerInterrupt) or presence
of a call progress tone (tone). Select configuration to match
customer equipment provisions. This parameter is ONLY configurable
for the Standard and Enhanced FXO voice modules.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.9 |
voiceFaxChPhyParaRingFrequencySelects the ringing frequency to be used to indicate an
incoming call. This parameter is ONLY configurable for the KTS,
3-Port Fax, and Standard and Enhanced FXS voice modules.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.10 |
voiceFaxChPhyParaJitterMaintains continuous voice delivery by compensating (in
milliseconds) for the transmission delay of packets. Jitter
provides compensation for the difference in arrival time and
expected arrival time of voice packets. (Range is 1 - 200 ms.)
This parameter is configurable by all voice modules with a
Channel Version (voiceFaxChPhyParaChannelVersion) equal to '5'
or higher and residing in an Integration Unit with a software
release (sysSoftwarePhase) of Phase 5.1 and Above (EXCLUDES
the E&M, KTS and OPX voice modules).ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.11 |
voiceFaxChPhyParaDTMFRegenerationDTMF Regeneration, when enabled, ensures that the DTMF
signals at the remote side are regenerated with a uniform
on/off time of 100 milliseconds. This option is only compatible
with other Voice/Fax modules that configure this parameter.
This parameter is configurable by all voice modules with a
Channel Version (voiceFaxChPhyParaChannelVersion) equal to '7'
or higher and residing in an Integration Unit with a software
release (sysSoftwarePhase) of Phase 5.1C and Above (EXCLUDES
the E&M, KTS and OPX voice modules).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.12 |
voiceFaxChPhyParaAutoLevelEnhancementAutomatic Level Enhancement, when enabled, boosts weak
input signals above the noise threshold to a minimum usable
level for voice/Fax channels. This parameter is configurable
by all voice modules with a Channel Version
(voiceFaxChPhyParaChannelVersion) equal to '5' or higher and
residing in an Integration Unit with a software release
(sysSoftwarePhase) of Phase 5.1 and Above (EXCLUDES the E&M,
KTS and OPX voice modules).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.13 |
voiceFaxChPhyParaBackgroundThe ability of passing background noise or silencing the
channel by the receiving voice channel DSP during idle periods.
First option allows the background noise to be regenerated
during the periods, whereas the second option suppresses
background noise during idle periods.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.14 |
voiceFaxChPhyParaDigitizingRateConfigures the compression bandwidth for the voice channel.
Larger bandwidths produce crisper voice communications. However,
larger voice channel bandwidths may result in overbooking of
composite bandwidth. The G.729 Digitizing Rate option (rateG729)
is ONLY configurable for voice modules with a Channel Version
(voiceFaxChPhyParaChannelVersion) equal to '5' or higher (EXCLUDES
the E&M, KTS and OPX voice modules).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.15 |
voiceFaxChPhyParaBusyModeControls how the busyout state of the channel is determined.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.16 |
voiceFaxChPhyParaVoiceFaxModeSelects the channel signal processing type, voice/fax or voice only.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.17 |
voiceFaxChPhyParaBandwidthAssignmentSelects how the channel uses link bandwidth: all the
time (continuous); only when voice/fax signals are present
(voiceActivated); or dynamically. Option 3 (dynamic) is not
valid when the voiceFaxChPhyParaDigitizingRate value is
configured for G.729.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.18 |
voiceFaxChPhyParaInputGainSelects one of 29 input level gain values in 1 dB increments.
This range of values applies only to the KTS, OPX, and E&M voice
modules. The remaining voice modules utilize the following 'value'
range: -6 thru 19, inclusive.rw INTEGER (-6..22) .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.19 |
voiceFaxChPhyParaChannelTypeUnconfigurable by the Userro INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.20 |
voiceFaxChPhyParaEMTypeStrappingReflects the Ear and Mouth circuit configuration type (I - V)
on voice/Fax channels that are strapped for E&M.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.21 |
voiceFaxChPhyParaOutputAttenuationSelects one out of 29 output level attenuation values in 1 dB
increments. 0 = no attenuation, 28 = maximum attenuation. This
range of values applies only to the KTS, OPX, and E&M voice modules.
The remaining voice modules utilize the following 'value' range:
0 thru 25, inclusive.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.22 |
voiceFaxChPhyParaPrioritySelects the priority of the channel, either high or low.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.23 |
voiceFaxChPhyParaFaxDigitizingRateSets the compression bandwidth for voice channel Fax operations.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.24 |
voiceFaxChPhyParaLineImpedanceProvides impedance matching choices for the Enhanced FXS,
Enhanced FXO, and Enhanced E&M 2-wire interface modules. This
parameter is ONLY configurable for these voice modules. The
port impedance of the E&M interface module configured for 4-wire
operation is fixed at 600 ohms resistive and is not configurable.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.25 |
voiceFaxChPhyParaMaxOutputLevelIntended to be used for equipment operated outside of U.S.A
and Canada. This parameter is ONLY configurable for the Enhanced
E&M voice module. Option (1) must be selected within the U.S.A
(or Canada) if this module was originally configured for 4-wire
operation and you have just reconfigured it to 2-wire operation.
Otherwise, the voice/fax module will not operate properly.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.26 |
voiceFaxChPhyParaRegenerationDelayThe selected delay, ranging from 1 to 15 seconds,
compensates for the time it takes for the remote PBX to
go off-hook and provide a dial tone to the voice channel
for completing the call setup. The default is 1 second.
This parameter is configurable for all voice modules with
a Channel Version (voiceFaxChPhyParaChannelVersion) greater
than or equal to '3' (EXCLUDES the E&M, KTS and OPX voice
modules).rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.27 |
voiceFaxChPhyParaMaxDialDigitTimeLimitThe dial digit time limit is the maximum time allowed
for accepting dialed digits. When the dial digit time
limit is reached, further digits are not accepted, and the
accumulated digits are compared to the configured number of
digits. If the accumulated number is less than the configured
number, a fast busy response is generated. If the accumulated
number is equal to or more than the configured number, the
digits are forwarded. The default is 10 seconds. This
parameter is configurable for all voice modules with a Channel
Version (voiceFaxChPhyParaChannelVersion) greater than or equal
to '3' (EXCLUDES the E&M, KTS and OPX voice modules).rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.28 |
voiceFaxChPhyParaMaxNumFwdDigitsThe selected value specifies the maximum number of
dialing digits to be forwarded to the destination voice
channel without having to wait until the dial digit time
limit is reached. The range is 0-16, with zero disabling
the store and forward feature. The default value is 0.
This parameter is configurable for all voice modules with
a Channel Version (voiceFaxChPhyParaChannelVersion) greater
than or equal to '3' (EXCLUDES the E&M, KTS and OPX voice
modules).rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.29 |
voiceFaxChPhyParaCallProgressionTonesThis option allows you to match the call progress to
those of one of eight countries or areas. This parameter
is configurable for all voice modules with a Channel Version
(voiceFaxChPhyParaChannelVersion) greater than or equal to
'3' (EXCLUDES the E&M, KTS and OPX voice modules).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.30 |
voiceFaxChPhyParaRegenFormatRegeneration format supports the store and forward function.
Dial format allows the voice/fax channel to match the outgoing
dialing digits format with the format of the interfacing PBX.
This parameter is configurable for all voice modules with
a Channel Version (voiceFaxChPhyParaChannelVersion) greater
than or equal to '3' (EXCLUDES the E&M, KTS and OPX voice
modules).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.31 |
voiceFaxChPhyParaChannelVersionIdentifies the voice/Fax compression algorithm used (installed
software version) by the voice/Fax channel.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.1.1.32 |
voiceFaxChSwParaTableTable for configuring the voice/Fax channel switching parameters. SEQUENCE OF VoiceFaxChSwParaEntry .1.3.6.1.4.1.335.1.2.1.3.4.3.2 |
voiceFaxChSwParaEntryEntry within the table to specify a particular voice/Fax channel number
on a specific module/card for channel switching configuration. VoiceFaxChSwParaEntry .1.3.6.1.4.1.335.1.2.1.3.4.3.2.1 |
voiceFaxChSwParaCardNumberIdentifies the module/card number for the voice/Fax channel specific
to the channel's switching parameters.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.3.2.1.1 |
voiceFaxChSwParaChannelNumberIdentifies the voice/Fax channel specific to the channel's
switching parameters.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.3.2.1.2 |
voiceFaxChSwParaVoiceExtensionDefines the voice extension for the voice/fax channel.
The voice extension must consist of NUMERIC characters
only; and the number of digits in the extension MUST match
the value set for the voiceFaxChSwNumberOfDigitsInPhoneNumber
parameter.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.4.3.2.1.3 |
voiceFaxChSwParaFaxExtensionDefines the fax extension for the voice/fax channel.
The fax extension must consist of NUMERIC characters only;
and the number of digits in the extension MUST match the
value set for the voiceFaxChSwNumberOfDigitsInPhoneNumber
parameter. This parameter is ONLY valid for 3-Port Fax
modules.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.4.3.2.1.4 |
voiceFaxChSwParaAutoCallNumberThis is the extension number of a voice/fax port that is
called immediately if this voice/fax port goes off hook.
If no entry is made in this field, this function is disabled.
The Auto Call Number must consist of NUMERIC characters only.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.4.3.2.1.5 |
voiceFaxChSwParaReceiveInhibitOption (1) prevents this voice/fax channel from receiving calls.
The default is Option (2).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.2.1.6 |
voiceFaxChSwParaCallInhibitOption (1) prevents this voice/fax channel from initiating calls.
The default is Option (2).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.3.2.1.7 |
voiceFaxChSwNumberOfDigitsInPhoneNumberNumber of digits in a phone number (1 - 4). Note that all
Integration units in a network must have the same value for
this parameter.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.3.3 |
digital-voice-channel OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.4.4 |
digitalVoiceChPhyParaTableTable for configuring digital voice module (DVM) physical
parameters. SEQUENCE OF DigitalVoiceChPhyParaEntry .1.3.6.1.4.1.335.1.2.1.3.4.4.1 |
digitalVoiceChPhyParaEntryEntry within the table to specify a particular DVM channel number
on a specific module/card. DigitalVoiceChPhyParaEntry .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1 |
digitalVoiceChPhyParaCardNumberIdentifies the module/card number for the DVM channel specific
to the channel's physical parameters.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.1 |
digitalVoiceChPhyParaChannelNumberIdentifies the DVM channel specific to the channel's
physical parameters.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.2 |
digitalVoiceChPhyParaViewSignallingTypeIndicates the DVM signalling type. Note that Options 3, 5, 6,
and 7 are only valid for E1 interfaces.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.3 |
digitalVoiceChPhyParaBergStrapTypeIndicates the Berg Hardware Strap configuration which is
a constant value for DVM channels.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.4 |
digitalVoiceChPhyParaPortEmulationIndicates the DVM port emulation. Note that Options 3, 5,
6, and 7 are only valid for E1 interfaces. Options 3, 6, and 7
are only configurable for DVMs with a Channel Version of '6' or
greater, and which are running in a CCM software release environment
of Phase 5.1 or greater.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.5 |
digitalVoiceChPhyParaSuppressionDuring idle periods in which suppression is enabled (=0),
the sending DVM channel DSP generates suppression service
frames containing a noise level estimate and no data. This
is sent to the receiving DVM channel DSP which will either
regenerate the noise level or silence the output depending on
the configuration of digitalVoiceChPhyParaBackground.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.6 |
digitalVoiceChPhyParaJitterMaintains continuous voice delivery by compensating (in
milliseconds) for the transmission delay of packets. Jitter
provides compensation for the difference in arrival time and
expected arrival time of DVM packets. (Range is 1 - 200 ms.).
This parameter is configurable for DVMs with a Channel Version
(voiceFaxChPhyParaChannelVersion) equal to '6' or higher, and
residing in an Integration Unit with a software release
(sysSoftwarePhase) of Phase 5.1 or Above.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.7 |
digitalVoiceChPhyParaDTMFRegenerationDTMF Regeneration, when enabled, ensures that the DTMF
signals at the remote side are regenerated with a uniform
on/off time of 100 milliseconds. This option is only compatible
with other Voice/Fax modules that configure this parameter.
This parameter is configurable DVMs with a Channel Version
(voiceFaxChPhyParaChannelVersion) of '7' or greater and residing
in an Integration Unit with a software release (sysSoftwarePhase)
of Phase 5.1C and Above.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.8 |
digitalVoiceChPhyParaAutoGainControlAutomatic Gain Control, when enabled, boosts weak
input signals above the noise threshold to a minimum
usable level for DVM channels.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.9 |
digitalVoiceChPhyParaBackgroundThe ability of passing background noise or silencing the channel
by the receiving DVM channel DSP during idle periods. First option
allows the background noise to be regenerated during the periods,
whereas the second option suppresses background noise during
idle periods.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.10 |
digitalVoiceChPhyParaDigitizingRateConfigures the compression bandwidth for the DVM channel.
Larger bandwidths produce crisper voice communications.
However, larger DVM channel bandwidths may result in overbooking
of composite bandwidth. The G.729 Digitizing Rate option
(rateG729) is ONLY configurable for DVMs with a Channel Version
(voiceFaxChPhyParaChannelVersion) of '5' or greater.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.11 |
digitalVoiceChPhyParaBusyModeControls how the busyout state of the DVM channel is determined.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.12 |
digitalVoiceChPhyParaVoiceFaxModeSelects the DVM channel signal processing type, voice/fax or
voice only.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.13 |
digitalVoiceChPhyParaBandwidthAssignmentSelects how the DVM channel uses link bandwidth: all the time
(continuous);only when voice/fax signals are present
(voiceActivated); or dynamically. Option 3 not valid for G.729
value of digitalVoiceChPhyParaDigitizingRate.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.14 |
digitalVoiceChPhyParaInputGainSelects one of 15 input level gain values in 1 dB increments.
The range is from -6 to 8, inclusive.rw INTEGER (-6..8) .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.15 |
digitalVoiceChPhyParaChannelTypeUnconfigurable by the Userro INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.16 |
digitalVoiceChPhyParaOutputAttenuationSelects one out of 9 DVM output level attenuation values in 1 dB
increments. The range is 0 - 8, where =0 is no attenuation and =8 is
maximum attenuation.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.17 |
digitalVoiceChPhyParaPrioritySelects the priority of the DVM channel, either high or low.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.18 |
digitalVoiceChPhyParaFaxDigitizingRateSets the compression bandwidth for DVM channel Fax operations.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.19 |
digitalVoiceChPhyParaRegenerationDelayThe selected delay, ranging from 1 to 15 seconds, compensates
for the time it takes for the remote PBX to go off-hook and
provide a dial tone to the DVM channel for completing the
call setup. The default is 1 second.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.20 |
digitalVoiceChPhyParaMaxDialDigitTimeLimitThe DVM dial digit time limit is the maximum time allowed for
accepting dialed digits. When the dial digit time limit is
reached, further digits are not accepted, and the accumulated
digits are compared to the configured number of digits. If the
accumulated number is less than the configured number, a fast
busy response is generated. If the accumulated number is equal
to or more than the configred number, the digits are forwarded.
The default is 10 seconds.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.21 |
digitalVoiceChPhyParaMaxNumFwdDigitsThe selected value specifies the maximum number of dialing
digits to be forwarded by the DVM to the destination voice
channel without having to wait until the DVM dial digit time limit
is reached. The range is 0-16, with zero disabling the store
and forward feature. The default value is 0.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.22 |
digitalVoiceChPhyParaCallProgressionTonesThis option allows you to match the DVM channel call progress
to those of one of eight countries or areas.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.23 |
digitalVoiceChPhyParaRegenerationFormatDVM regeneration format supports the store
and forward function. Designed for E&M and FXO interfaces,
regeneration format allows the DVM channel to match the outgoing
dialing digits format with the format of the interfacing PBX.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.24 |
digitalVoiceChPhyParaCompanderOption (1), uLaw, should be selected as the standard t1
compander format. Option (2), aLaw, should be selected as
the standard e1 compander format. Note that there is a rare
mismatch to t1 equipment that uses an aLaw compander format.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.25 |
digitalVoiceChPhyParaPremiumVoiceOption (2) allows transparent pass-through of uncompressed
voice frames between DVM ports. This option is used when two
Integration unit voice ports may connect through the same PBX.
Option (1) is used for normal operation in which calls always
terminate in a telephone set. This parameter is configurable
for DVMs with a Channel Version (voiceFaxChPhyParaChannelVersion)
equal to '5' or higher.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.26 |
digitalVoiceChPhyParaModuleIdentificationIdentifies whether the DVM interfaces with a t1 vs. an e1 card.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.27 |
digitalVoiceChPhyParaChannelVersionIdentifies the compression algorithm used (installed software
version) by the DVM channel.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.4.1.1.28 |
digitalVoiceChSwParaTableTable for configuring the DVM channel switching parameters. SEQUENCE OF DigitalVoiceChSwParaEntry .1.3.6.1.4.1.335.1.2.1.3.4.4.2 |
digitalVoiceChSwParaEntryEntry within the table to specify a particular DVM channel number
on a specific module/card for channel switching configuration. DigitalVoiceChSwParaEntry .1.3.6.1.4.1.335.1.2.1.3.4.4.2.1 |
digitalVoiceChSwParaCardNumberIdentifies the module/card number for the DVM channel specific
to the channel's switching parameters.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.4.2.1.1 |
digitalVoiceChSwParaChannelNumberIdentifies the DVM channel specific to the channel's
switching parameters.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.4.4.2.1.2 |
digitalVoiceChSwParaVoiceExtensionDefines the voice extension for the DVM channel.
The voice extension must consist of NUMERIC characters
only.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.4.4.2.1.3 |
digitalVoiceChSwParaAutoCallNumberThis is the extension number of a voice/fax port that is
called immediately if this DVM channel goes 'off hook'.
If no entry is made in this field, this function is disabled.
The Auto Call Number must consist of NUMERIC characters only.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.4.4.2.1.4 |
digitalVoiceChSwParaReceiveInhibitOption (1) prevents this DVM channel from receiving calls.
The default is Option (2).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.4.2.1.5 |
digitalVoiceChSwParaCallInhibitOption (1) prevents this DVM channel from initiating calls.
The default is Option (2).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.4.4.2.1.6 |
link OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.5 |
mux-link OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.5.1 |
muxLinkCfgTableTable for configuring the clocking for a Mux Feeder link. SEQUENCE OF MuxLinkCfgEntry .1.3.6.1.4.1.335.1.2.1.3.5.1.1 |
muxLinkCfgEntryEntry within the table to specify a particular Mux link port
number on a specific module/card. MuxLinkCfgEntry .1.3.6.1.4.1.335.1.2.1.3.5.1.1.1 |
muxLinkCfgCardNumberIdentifies the module/card number specific to a particular
Mux link port.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.1.1.1.1 |
muxLinkCfgChannelNumberIdentifies the specific Mux Link port number specific to
the link's clocking configuration.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.1.1.1.2 |
muxLinkCfgDataRateSets the type of clocking to be used on the mux link to be
configured. Note: When the value of this parameter is
changed the link must be reset.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.1.1.1.3 |
muxOrLEsiPreConfigTableTable to pre-configure the data rate of a Mux or Local ESI (LIL)
Link prior to configuring the port as a Mux or LIL link. By
using this table to 'preset' the data rate, only 1 node reset
is needed following the port link assignment to complete the
configuration. SEQUENCE OF MuxOrLEsiPreConfigEntry .1.3.6.1.4.1.335.1.2.1.3.5.1.2 |
muxOrLEsiPreConfigEntryEntry within the table to specify a particular port for Mux or
LIL pre-configuration on a specific module/card. MuxOrLEsiPreConfigEntry .1.3.6.1.4.1.335.1.2.1.3.5.1.2.1 |
muxOrLEsiPreConfigCardNumberIdentifies the module/card for Mux or LIL link pre-configuration.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.1.2.1.1 |
muxOrLEsiPreConfigChannelNumberIdentifies the port number for Mux or LIL link pre-configuration.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.1.2.1.2 |
muxOrLEsiPreConfigDataRateSets the data rate in bits per second for Mux and
LIL link pre-configurations.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.1.2.1.3 |
esi-link OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.5.2 |
esiLinkCfgTableTable for configuring the data rate of an ESI (aka
Interconnect) link. SEQUENCE OF EsiLinkCfgEntry .1.3.6.1.4.1.335.1.2.1.3.5.2.1 |
esiLinkCfgEntryEntry into the table pertaining to a specific ESI link on a
specific module/card. EsiLinkCfgEntry .1.3.6.1.4.1.335.1.2.1.3.5.2.1.1 |
esiLinkCfgCardNumberIdentifies the module/card number specific to the ESI link
for data rate configuration.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.2.1.1.1 |
esiLinkCfgChannelNumberIdentifies the ESI link port specific to the data rate
configuration.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.2.1.1.2 |
esiLinkCfgDataRateSets the link clocking method to external, or if internal, the
data rate. Note: When the value of this parameter is changed,
the link must be reset.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.2.1.1.3 |
esiOrSecLinkPreConfigTableTable to pre-configure the data rate of an ESI (aka Interconnect)
Link (or secondary link) prior to configuring the link port. By
using this table to 'preset' the data rate, only 1 node reset
is needed following the port link assignment to complete the
configuration. SEQUENCE OF EsiOrSecLinkPreConfigEntry .1.3.6.1.4.1.335.1.2.1.3.5.2.2 |
esiOrSecLinkPreConfigEntryEntry within the table to specify a particular port for ESI or
secondary link pre-configuration on a specific module/card. EsiOrSecLinkPreConfigEntry .1.3.6.1.4.1.335.1.2.1.3.5.2.2.1 |
esiOrSecLinkPreConfigCardNumberIdentifies the module/card for ESI or secondary link
pre-configuration.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.2.2.1.1 |
esiOrSecLinkPreConfigChannelNumberIdentifies the port number for ESI or secondary link
pre-configuration.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.2.2.1.2 |
esiOrSecLinkPreConfigDataRateSets the data rate in bits per second for ESI and secondary
link pre-configurations. Note: The only valid data rate
value for Secondary links is 'external (1)'. (Secondary links
exclusively use external clocking.)rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.2.2.1.3 |
esiOrSecLinkAssignCfgTableTable for configuring the activation and deactivation
of ESI (aka Interconnect) and secondary links. SEQUENCE OF EsiOrSecLinkAssignCfgEntry .1.3.6.1.4.1.335.1.2.1.3.5.2.3 |
esiOrSecLinkAssignCfgEntryEntry into the table pertaining to a specific ESI or secondary
link for activation/deactivation configuration on a specific
module/card. EsiOrSecLinkAssignCfgEntry .1.3.6.1.4.1.335.1.2.1.3.5.2.3.1 |
esiOrSecLinkAssignCfgCardNumberIdentifies the module/card number specific to the ESI or
secondary link for activation/deactivation configuration.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.2.3.1.1 |
esiOrSecLinkAssignCfgChannelNumberIdentifies the ESI or secondary link port specific to the
activation/deactivation configuration.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.2.3.1.2 |
esiOrSecLinkAssignCfgLinkForcedOnBoth the primary and secondary links can be configured
as Forced On. This overrides the current time of day and
utilization restrictions for testing, or to provide bandwidth
during a normally off period without changing other
configuration. The default is YES for primary links and
NO for secondary links.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.2.3.1.3 |
esiOrSecLinkAssignCfgSecLinkBackUpOnlyIf the primary or secondary link is configured to be off,
according to the time of day configuration, then the secondary
link will not be activated upon primary link. The default value,
Yes, indicates the secondary link is for backup only.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.2.3.1.4 |
esiOrSecLinkAssignCfgUtilThresholdToActivateSecThis option allows utilization thresholds to be set for
activation of the secondary link. Utilization thresholds
are specified as a percentage of available bandwidth on the
primary link. Secondary channels may be configured to become
active when the bandwidth utilization on the primary link
exceeds a predetermined threshold. The secondary link will
also be activated if primary link failure is detected. However,
the secondary link will not be activated if either the secondary
or primary link is configured to be off according to the time
of day configuration. The default value is 75.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.2.3.1.5 |
esiOrSecLinkAssignCfgUtilThresholdToDeactivateSecThis option allow utilization thresholds to be set for
deactivation of the secondary link. The secondary link will
be de-activated when the total utilization drops below a configured
threshold. The de-activation threshold value must be less than
the activation threshold value. The default value is 50.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.2.3.1.6 |
esiOrSecLinkAssignCfgTimeThresholdExceedToActivateSecTime (in minutes) that utilization threshold (to activate) must
be exceeded to activate a secondary link. The default value is 5.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.2.3.1.7 |
esiOrSecLinkAssignCfgTimeThresholdBelowToDeactivateSecTime (in minutes) that utilization threshold (to deactivate) must
be below to deactivate a secondary link. The default value is 5.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.2.3.1.8 |
esiOrSecLinkAssignCfgTerminateCallonDeactivationThis parameter allows the option of leaving a link up if a
switched voice call is in place even if the time of day
configuration indicates it is time to deactivate the link.
Setting this parameter to NO will bring down the link only
when all switched voice calls have hung up. The default is NO.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.2.3.1.9 |
esiOrSecLinkTODActivationTableTable for configuring the Time Of Day (TOD) activation
and deactivation schedule of ESI (aka Interconnect) and
secondary links. SEQUENCE OF EsiOrSecLinkTODActivationEntry .1.3.6.1.4.1.335.1.2.1.3.5.2.4 |
esiOrSecLinkTODActivationEntryEntry into the table pertaining to a specific module/card,
port location, day schedule, and time schedule for setting
ESI or secondary link activation/deactivation configurations. EsiOrSecLinkTODActivationEntry .1.3.6.1.4.1.335.1.2.1.3.5.2.4.1 |
esiOrSecLinkTODActivationCardNumberIdentifies the module/card number specific to an ESI or secondary
link for the TOD activation/deactivation schedule.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.2.4.1.1 |
esiOrSecLinkTODActivationChannelNumberIdentifies the port location specific to an ESI or secondary
link for the TOD activation/deactivation schedule.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.2.4.1.2 |
esiOrSecLinkTODActivationSetScheduleIdentifies the particular day(s) schedule specific to an ESI
or secondary link for the TOD activation/deactivation schedule.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.2.4.1.3 |
esiOrSecLinkTODActivationTenMinIntervalIdentifies the particular time of day (in 10 minute intervals)
specific to an ESI or secondary link for the TOD
activation/deactivation schedule.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.2.4.1.4 |
esiOrSecLinkTODActivationLinkStateSets the TOD link state for an ESI or secondary link. This
parameter is used to configure a link to active (on) or not active
(off) for a particular 10 minute interval as specified by the
previous 4 indexing parameters contained in this table.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.2.4.1.5 |
x-dot-21-link OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.5.3 |
x21LinkCfgTableTable to configure the X.21 links. It defines the X.21 parameters
for the Integration unit and for the MICOM mux side. SEQUENCE OF X21LinkCfgEntry .1.3.6.1.4.1.335.1.2.1.3.5.3.1 |
x21LinkCfgEntryEntry in the table for a particular X.21 link. Note that a link
reset is required if any value in this table is changed. X21LinkCfgEntry .1.3.6.1.4.1.335.1.2.1.3.5.3.1.1 |
x21LinkCfgCardNumberThe card/module number of the X.21 link channel the entry pertains to.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.3.1.1.1 |
x21LinkCfgChannelNumberThe particular X.21 link channel on specific module to be configured.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.3.1.1.2 |
x21LinkCfgLocalConnectModeConfigures the Integration unit side of the X.21 link.
In Integration units, the only connect mode for X.21
links is data activity connect. In this mode, the Integration
unit will place a call over the X.21 network whenever data
activity is detected on any force connected channel, matrix
connection, or port connected to a class defined with ports on
a MICOM mux attached to an X.21 link.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.3.1.1.3 |
x21LinkCfgRemoteConnectModeConfigures the MICOM mux side of the X.21 link. There
are two options: DTR and Data Activity Connect. DTR
(DTR connect) establishes the X.21 connection whenever
DTR is raised on any terminal connected to the MICOM mux.
Data Activity Connect establishes the X.21 connection
whenever data activity is detected on any terminal connected
to the MICOM mux.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.3.1.1.4 |
x21LinkCfgLocalConnectTimeoutThe value in this field specifies the amount of time that if no
data activity is detected, the X.21 connection will be dropped.
The default is 5 seconds.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.3.1.1.5 |
x21LinkCfgRemoteConnectTimeoutIf data activity connect mode is selected for the remote MICOM
mux, this field specifies the amount of time that if no data
activity is detected on any of the MICOM mux's channels, the X.21
connection will be dropped. The default is 5 seconds.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.3.1.1.6 |
x21LinkCfgLocalConnectRetriesConfigures the number of attempts the Integration unit will make to
place a call over the X.21 network.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.3.1.1.7 |
x21LinkCfgRemoteConnectRetriesConfigures the number of attempts the MICOM mux will
make to place a call over the X.21 network.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.3.1.1.8 |
x21LinkPreConfigTableTable to configure an X.21 link prior to configuring
a port as an X.21 link. By using this table to 'preset' the X.21
link parameters, only 1 node reset is needed following the X.21
assignment to complete the configuration. SEQUENCE OF X21LinkPreConfigEntry .1.3.6.1.4.1.335.1.2.1.3.5.3.2 |
x21LinkPreConfigEntryEntry within the table to specify a particular port number for
pre-configuration of an X.21 link on a specific module/card. X21LinkPreConfigEntry .1.3.6.1.4.1.335.1.2.1.3.5.3.2.1 |
x21LinkPreConfigCardNumberThe card/module number of the X.21 link channel to be pre-configured.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.3.2.1.1 |
x21LinkPreConfigChannelNumberThe particular X.21 link channel on specific module to be
pre-configured.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.3.2.1.2 |
x21LinkPreConfigLocalConnectModePre-configures the Integration unit side of the X.21 link.
In Integration units, the only connect mode for X.21
links is data activity connect. In this mode, the Integration
unit will place a call over the X.21 network whenever data
activity is detected on any force connected channel, matrix
connection, or port connected to a class defined with ports on
a MICOM mux attached to an X.21 link.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.3.2.1.3 |
x21LinkPreConfigRemoteConnectModePre-configures the MICOM mux side of the X.21 link. There
are two options: DTR and Data Activity Connect. DTR
(DTR connect) establishes the X.21 connection whenever
DTR is raised on any terminal connected to the MICOM mux.
Data Activity Connect establishes the X.21 connection
whenever data activity is detected on any terminal connected
to the MICOM mux.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.3.2.1.4 |
x21LinkPreConfigLocalConnectTimeoutPre-configuration of this field specifies the amount of time that
if no data activity is detected, the X.21 connection will be dropped.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.3.2.1.5 |
x21LinkPreConfigRemoteConnectTimeoutIf data activity connect mode is selected for the remote MICOM
mux, pre-configuration of this field specifies the amount of time
that if no data activity is detected on any of the MICOM mux's
channels, the X.21 connection will be dropped.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.3.2.1.6 |
x21LinkPreConfigLocalConnectRetriesPre-configures the number of attempts the Integration unit will
make to place a call over the X.21 network.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.3.2.1.7 |
x21LinkPreConfigRemoteConnectRetriesPre-configures the number of attempts the MICOM mux will
make to place a call over the X.21 network.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.3.2.1.8 |
local-esi-link OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.5.4 |
localESILinkCfgTableTable to configure the data rate for a local ESI link
(aka Local Interconnect Link or LIL). SEQUENCE OF LocalESILinkCfgEntry .1.3.6.1.4.1.335.1.2.1.3.5.4.1 |
localESILinkCfgEntryEntry within the table to specify a particular port number
on a specific module/card for an LIL configuration. LocalESILinkCfgEntry .1.3.6.1.4.1.335.1.2.1.3.5.4.1.1 |
localESILinkCfgCardNumberIdentifies the specific module/card number for an LIL
configuration.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.4.1.1.1 |
localESILinkCfgChannelNumberIdentifies the specific port number for an LIL configuration.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.4.1.1.2 |
localESILinkCfgDataRateSets the link clocking method to external, or if internal, the
data rate for an LIL. Note: When the value of this parameter is
changed, the link must be reset.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.4.1.1.3 |
esi-secondary-link OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.5.5 |
esiSecLinkCfgTableTable to configure the data rate for a secondary ESI link. SEQUENCE OF EsiSecLinkCfgEntry .1.3.6.1.4.1.335.1.2.1.3.5.5.1 |
esiSecLinkCfgEntryEntry within the table to specify a particular port number
on a specific module/card for a secondary ESI link configuration. EsiSecLinkCfgEntry .1.3.6.1.4.1.335.1.2.1.3.5.5.1.1 |
esiSecLinkCfgCardNumberIdentifies the specific module/card number for a secondary
ESI link configuration.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.5.1.1.1 |
esiSecLinkCfgChannelNumberIdentifies the specific port number for a secondary ESI link
configuration.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.5.1.1.2 |
esiSecLinkCfgDataRateSets the link clocking method to external, or if internal, the
data rate for a secondary ESI link. Note: When the value of this
parameter is changed, the link must be reset.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.5.1.1.3 |
esiSecLinkAssignmentTableTable to assign a secondary link channel to a primary
ESI link. SEQUENCE OF EsiSecLinkAssignmentEntry .1.3.6.1.4.1.335.1.2.1.3.5.5.2 |
esiSecLinkAssignmentEntryEntry within the table to specify a particular link/port
on a specific module/card for a secondary assignment to a
primary link. EsiSecLinkAssignmentEntry .1.3.6.1.4.1.335.1.2.1.3.5.5.2.1 |
esiSecLinkAssignmentSecCardNumberIdentifies the specific module/card number of the link
to be assigned as the secondary link.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.5.2.1.1 |
esiSecLinkAssignmentSecChannelNumberIdentifies the specific link/port number of the link
to be assigned as the secondary link.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.5.2.1.2 |
esiSecLinkAssignmentEntryActionThis is the command to perform the secondary link assignment.
Selecting 'active' following the successful setting of
esiSecLinkAssignmentPriCardNumber & esiSecLinkAssignmentPriChannelNumber
will complete the assignment.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.5.2.1.3 |
esiSecLinkAssignmentPriCardNumberIndicates the card number where the primary link channel is residing.
A GET value of FFh indicates that no secondary link assignment
currently exists. A SET with a value of zero (0)
with zero (0) as the channel number de-assigns the link.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.5.2.1.4 |
esiSecLinkAssignmentPriChannelNumberIndicates the channel number where the primary channel is residing.
A read value of FFh indicates that no secondary link assignment
currently exists. A SET with a value of zero (0)
with zero (0) as the card number de-assigns the link.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.5.2.1.5 |
frame-relay-link OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.5.6 |
frameRelayLinkCfgTableTable to configure a Frame Relay link. SEQUENCE OF FrameRelayLinkEntry .1.3.6.1.4.1.335.1.2.1.3.5.6.1 |
frameRelayLinkCfgEntryEntry within the table to specify a particular port number
on a specific module/card for a Frame Relay link configuration. FrameRelayLinkEntry .1.3.6.1.4.1.335.1.2.1.3.5.6.1.1 |
frameRelayLinkCfgCardNumberIdentifies the specific module/card number for a Frame Relay
link configuration.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.1.1.1 |
frameRelayLinkCfgChannelNumberIdentifies the specific port number for a Frame Relay link
configuration.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.1.1.2 |
frameRelayLinkCfgDataRateSets the data rate for a Frame Relay link. Note: If the
frame relay access link is externally clocked, no configuration
of this paramter is necessary.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.6.1.1.3 |
frameRelayLinkCfgLocalMgmtProtocolSets the frame relay access link local management protocol.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.6.1.1.4 |
frameRelayLinkCfgFullStatusPollingCounterSets the frame relay access link full status poll counter.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.1.1.5 |
frameRelayLinkCfgErrorThresholdSets the frame relay access link error threshold.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.1.1.6 |
frameRelayLinkCfgEventCountSets the frame relay access link monitored events count.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.1.1.7 |
frameRelayLinkCfgLinkIntegrityVerificationTimerSets the frame relay access link integrity verification
timer.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.1.1.8 |
frameRelayLinkCfgPollingVerificationTimerSets the frame relay access link polling verification
timer.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.1.1.9 |
frameRelayLinkCfgMaxFrameSizeSets the maximum frame relay access link frame size.
The numbers are in octets.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.1.1.10 |
frameRelayLinkCfgRxClockingSourceSets the port clocking configuration for receiving
data over the frame relay access link.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.6.1.1.11 |
frameRelayLinkCfgTxClockingSourceSets the port clocking configuration for transmitting
data over the frame relay access link.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.6.1.1.12 |
frameRelayLinkCfgNetworkAddressSets the network address for the frame relay access link.
This address is assigned by the carrier provider based on
a standardized numbering scheme.rw OCTET STRING .1.3.6.1.4.1.335.1.2.1.3.5.6.1.1.13 |
frameRelayLinkCfgAccessLinkModeSets the access mode for the frame relay access link.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.6.1.1.14 |
frameRelayLinkCfgDLCITableTable to configure the DLCI bandwidth charactistics for a
frame relay link. SEQUENCE OF FrameRelayLinkCfgDLCIEntry .1.3.6.1.4.1.335.1.2.1.3.5.6.2 |
frameRelayLinkCfgDLCIEntryEntry within the table to specify a DLCI number, the FR link/port
number, and the module/card number for setting DLCI bandwidth
characteristics. FrameRelayLinkCfgDLCIEntry .1.3.6.1.4.1.335.1.2.1.3.5.6.2.1 |
frameRelayLinkCfgDLCICardNumberIdentifies the module/card number for a particular DLCI
of a specific FR link for setting DLCI bandwidth characteristics.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.2.1.1 |
frameRelayLinkCfgDLCIChannelNumberIdentifies the FR link/port number of a particular DLCI channel
for setting the bandwidth characteristics.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.2.1.2 |
frameRelayLinkCfgDLCINumberIdentifies a particular DLCI number for setting the bandwidth
characteristics.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.2.1.3 |
frameRelayLinkCfgDLCITypeIdentifies the DLCI type configuration. Note that only
Options (3), (5), and (6) are expected.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.6.2.1.4 |
frameRelayLinkCfgDLCICommittedInfoRateForwardSets the value for committed information rate forward.
This value is available from your frame relay service provider.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.2.1.5 |
frameRelayLinkCfgDLCICommittedInfoRateBackwardSets the value for committed information rate backward.
This value is available from your frame relay service provider.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.2.1.6 |
frameRelayLinkCfgDLCICommittedBurstSizeForwardSets the value for committed burst size backward.
This value is available from your frame relay service provider.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.2.1.7 |
frameRelayLinkCfgDLCICommittedBurstSizeBackwardSets the value for committed burst size forward.
This value is available from your frame relay service provider.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.2.1.8 |
frameRelayLinkCfgDLCIExcessBurstSizeForwardSets the value for excess burst size backward.
This value is available from your frame relay service provider.
Note: should be equal to the FR access data rate minus the
CIR backward.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.2.1.9 |
frameRelayLinkCfgDLCIExcessBurstSizeBackwardSets the value for excess burst size forward.
This value is available from your frame relay service provider.
Note: should be equal to the FR access data rate minus the
CIR forward.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.2.1.10 |
frameRelayLinkControlTableTable to add or delete DLCI channels for a FR link. SEQUENCE OF FrameRelayLinkControlEntry .1.3.6.1.4.1.335.1.2.1.3.5.6.3 |
frameRelayLinkControlEntryEntry within the table to specify a particular DLCI number
for addition/deletion to a particular FR access link on a
specific module/card. FrameRelayLinkControlEntry .1.3.6.1.4.1.335.1.2.1.3.5.6.3.1 |
frameRelayLinkControlLinkCardNumberIdentifies the module/card number of a FR access link for
adding/deleting a DLCI channel.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.3.1.1 |
frameRelayLinkControlLinkChannelNumberIdentifies a FR access link/port number for adding/deleting
a DLCI channel.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.3.1.2 |
frameRelayLinkControlDLCINumberSets the DLCI channel number to be added or deleted.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.3.1.3 |
frameRelayLinkControlCommandCommand to select whether the DLCI number specified in
frameRelayLinkControlDLCINumber is to be added or deleted.
This command sould be sent ater the DLCI type has been sent.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.6.3.1.4 |
frameRelayLinkControlDLCITypeSets the type of DLCI channel that is being added.
This object should be set before the previous command
object is set.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.6.3.1.5 |
frameRelayDLCIControlTableTable to configure force connections from one DLCI channel
on a FR access link to another FR access link DLCI channel.
Note: This will connect 2 FR access links together on a single
Integration unit which acts like a FR switch. SEQUENCE OF FrameRelayDLCIControlEntry .1.3.6.1.4.1.335.1.2.1.3.5.6.4 |
frameRelayDLCIControlEntryEntry within the table specifying a particular DLCI channel,
a FR access link/port number, and module/card number for a
force connection configuration. FrameRelayDLCIControlEntry .1.3.6.1.4.1.335.1.2.1.3.5.6.4.1 |
frameRelayDLCIControlLinkCardNumberIdentifies the module/card number of the source FR access link
for force connection configuration.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.4.1.1 |
frameRelayDLCIControlLinkChannelNumberIdentifies the port/channel number of the source FR access link
for force connection configuration.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.4.1.2 |
frameRelayDLCIControlDLCINumberIdentifies the DLCI channel number of the source FR access link
for force connection configuration.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.4.1.3 |
frameRelayDLCIControlCommandSelects the force connection configuration between 2 FR access
links on a single Integration unit.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.5.6.4.1.4 |
frameRelayDLCIControlFconnNodeNameSelects the name of the Integration unit for the FR link force
connection configuration.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.5.6.4.1.5 |
frameRelayDLCIControlFconnCardNumberSelects the module/card number of the destination FR access link
for force connection configuration.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.4.1.6 |
frameRelayDLCIControlFconnChannelNumberSelects the port/channel number of the destination FR access link
for force connection configuration.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.4.1.7 |
frameRelayDLCIControlFconnDLCINumberSelects the DLCI channel number of the destination FR access link
for force connection configuration.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.4.1.8 |
frameRelayDLCIConnectsTableTable to view DLCI connections between FR access links. SEQUENCE OF FrameRelayDLCIConnectsEntry .1.3.6.1.4.1.335.1.2.1.3.5.6.5 |
frameRelayDLCIConnectsEntryEntry within the table specific to the FR access link
module/card number, the port/channel number, and DLCI
channel number for viewing DLCI connections. FrameRelayDLCIConnectsEntry .1.3.6.1.4.1.335.1.2.1.3.5.6.5.1 |
frameRelayDLCIConnectsLinkCardNumberIdentifies the module/card number of the source FR access link
to view connection configurations.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.5.1.1 |
frameRelayDLCIConnectsLinkChannelNumberIdentifies the port/channel number of the source FR access link
to view connection configurations.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.5.1.2 |
frameRelayDLCIConnectsDLCIConnectedIdentifies the DLCI channel number of the source FR access link
to view connection configurations.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.5.1.3 |
frameRelayDLCIConnectsDestCardNumberIdentifies the module/card number of the destination FR access link
to view connection configurations.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.5.1.4 |
frameRelayDLCIConnectsDestChannelNumberIdentifies the port/channel number of the destination FR access link
to view connection configurations.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.5.1.5 |
frameRelayDLCIConnectsDestDLCINumberIdentifies the DLCI channel number of the destination FR access link
to view connection configurations.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.5.6.5.1.6 |
interface OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.6 |
t1-interface OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.6.1 |
t1DS1InterfaceTableTable for Network T1 Interface for long-haul connection to the
telephone network. SEQUENCE OF T1DS1InterfaceEntry .1.3.6.1.4.1.335.1.2.1.3.6.1.1 |
t1DS1InterfaceEntryEntry within the table for specified (Network Interface) DSO
(1..24) channels. T1DS1InterfaceEntry .1.3.6.1.4.1.335.1.2.1.3.6.1.1.1 |
t1DS1InterfaceDS0IndexIndicates an instance into the table for a particular (1..24)
DSO channel.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.6.1.1.1.1 |
t1DS1InterfaceConnectionStateDefines the connection state of the specified DSO channel. This
defines the ability for data passed directly between the Local
and Network Interfaces, or for being dropped and inserted to/from
the Integration unit resources (CCM links, Data Ports, Voice
Channels).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.1.1.2 |
t1DSX1InterfaceTableTable for Local T1 Interface for connection to local digital pbx. SEQUENCE OF T1DSX1InterfaceEntry .1.3.6.1.4.1.335.1.2.1.3.6.1.2 |
t1DSX1InterfaceEntryEntry within the table for specified (local interface) DSO (1..24)
channels. T1DSX1InterfaceEntry .1.3.6.1.4.1.335.1.2.1.3.6.1.2.1 |
t1DSX1InterfaceDS0IndexIndicates an instance into the table for a particular (1..24)
DSO channel for local t1 interfaces.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.6.1.2.1.1 |
t1DSX1InterfaceConnectionStateFor local t1 interfaces, this parameter defines the connection
state of the specified DSO channel. This defines the ability for
data passed directly between the Local and Network Interfaces,
or for being dropped and inserted to/from the Integration unit
resources (CCM links, Data Ports, Voice Channels).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.2.1.2 |
t1CfgGroup OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.6.1.3 |
t1CfgDSX1FrameFormatConfigures the local T1 interface frame formats to either (SF)
super frame or (ESF) extended super frame.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.1 |
t1CfgDSX1LineCodeConfigures the line coding method (at the Local interface) either
to Alternate Mark Inversion (AMI) coding or Bipolar Eight Zero
Suppression (B8ZS). In AMI 0's are indicated by the absence of a
pulse, and 1's are indicated by either a positive or negative polarity
pulse. In B8ZS an all 0 byte is replaced by a special code of 00011011
which indicate two fixed bipolar code violations. On remote end these
violations are ignored and the data is retrieved.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.2 |
t1CfgDSX1IdleCodeConfigures the idle code character at the local T1 interface.rw OCTET STRING .1.3.6.1.4.1.335.1.2.1.3.6.1.3.3 |
t1CfgDSX1lineBuildoutConfigures a transmitter attenuation parameter based on various
cable lengths, reflecting the distance from the T1 Access Module
to the T1 service provider.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.4 |
t1CfgDSX1NetworkInvokedLoopbackEnables/Disables the DSX1 Network-invoked loopback on the T1
module.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.5 |
t1CfgDS1FrameFormatConfigures the network T1 interface frame formats to either (SF)
super frame or (ESF) extended super frame.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.6 |
t1CfgDS1LineCodeConfigures the line coding method (at the Network interface) either
to Alternate Mark Inversion (AMI) coding or Bipolar Eight Zero
Suppression (B8ZS). In AMI 0's are indicated by the absence of a
pulse, and 1's are indicated by either a positive or negative polarity
pulse. In B8ZS an all 0 byte is replaced by a special code of 00011011
which indicate two fixed bipolar code violations. On remote end these
violations are ignored and the data is retrieved.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.7 |
t1CfgDS1IdleCodeConfigures the idle code character at the network T1 interface.rw OCTET STRING .1.3.6.1.4.1.335.1.2.1.3.6.1.3.8 |
t1CfgDS1NetworkInvokedLoopbackEnables/Disables the DS1 Network-invoked loopback on the T1
module.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.9 |
t1CfgDataPort1RateSets the base rate of Data Port channel 1 on the T1 module.
The actual rate will be determined by the following formula:
rate of the data port = (base rate)*(number of DS0 channels).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.10 |
t1CfgDataPort1TimingSets how the clocking will be supplied for Data Port 1 on the
T1 module.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.11 |
t1CfgDataPort1DTRControlSets the DTR control for Data Port 1 on the T1 module. Option (1),
dtrNormal, will configure DTR control from the DTE equipment.
Option (2), dtrForced, will force DTR to a '1'.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.12 |
t1CfgDataPort1RTSControlSets the RTS control for Data Port 1 on the T1 module. Option (1),
rtsNormal, will configure RTS control from the DTE equipment.
Option (2), rtsForced, will force RTS to a '1'.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.13 |
t1CfgDataPort2RateSets the base rate of Data Port channel 2 on the T1 module.
The actual rate will be determined by the following formula:
rate of the data port = (base rate)*(number of DS0 channels).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.14 |
t1CfgDataPort2TimingSets how the clocking will be supplied for Data Port 2 on the
T1 module.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.15 |
t1CfgDataPort2DTRControlSets the DTR control for Data Port 2 on the T1 module. Option (1),
dtr, will configure DTR control from the DTE equipment.
Option (2), dtrForcedOn, will force DTR to a '1'.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.16 |
t1CfgDataPort2RTSControlSets the RTS control for Data Port 2 on the T1 module. Option (1),
rts, will configure RTS control from the DTE equipment.
Option (2), rtsForcedOn, will force RTS to a '1'.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.17 |
t1CfgCCMLinkA1RateSets the base rate of the CCM A1 channel for a T1 interface.
The actual rate will be determined by the following formula:
rate of the CCM port = (base rate)*(number of DS0 channels).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.18 |
t1CfgCCMLinkA2RateSets the base rate of the CCM A2 channel for a T1 interface.
The actual rate will be determined by the following formula:
rate of the CCM port = (base rate)*(number of DS0 channels).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.19 |
t1CfgCCMLinkA3RateSets the base rate of the CCM A3 channel for a T1 interface.
The actual rate will be determined by the following formula:
rate of the CCM port = (base rate)*(number of DS0 channels).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.20 |
t1CfgCCMLinkA4RateSets the base rate of the CCM A4 channel for a T1 interface.
The actual rate will be determined by the following formula:
rate of the CCM port = (base rate)*(number of DS0 channels).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.21 |
t1CfgCCMLinkA5RateSets the base rate of the CCM A5 channel for a T1 interface.
The actual rate will be determined by the following formula:
rate of the CCM port = (base rate)*(number of DS0 channels).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.22 |
t1CfgCCMLinkA6RateSets the base rate of the CCM A6 channel for a T1 interface.
The actual rate will be determined by the following formula:
rate of the CCM port = (base rate)*(number of DS0 channels).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.23 |
t1CfgSystemClockSourceConfigures the source of the clock used in the T1 Access
Module. Options include:
- DSX-1. The clock source is from the DSX-1 interface.
- DS-1. The clock source is from the DS-1 interface.
- Internal. The clock is derived from a clock source internal
to the T1 Access Module.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.24 |
t1CfgDS1ConfigThis object is a write only object that will signal the proxy to
start caching changes to the DS1 ds0 connection tables. This is done to
solve an anomaly in the marathon/t1 design. The manager must set
this object to init before updating any of the t1DS1InterfaceTable objects.
When all the changes have been set then this object will have to be set to
commit (2). The init will cause the proxy to upload the table from the marathon
and the commit will cause the proxy to send all the changes to the marathon.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.25 |
t1CfgDSX1ConfigThis object is a write only object that will signal the proxy to
start caching changes to the DSX1 ds0 connection tables. This is done to
solve an anomaly in the marathon/t1 design. The manager must set
this object to init before updating any of the t1DSX1InterfaceTable objects.
When all the changes have been set then this object will have to be set to
commit (2). The init will cause the proxy to upload the table from the marathon
and the commit will cause the proxy to send all the changes to the marathon.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.3.26 |
t1FlashControlTableTable to control (erase) T1 flash memory in preparation for a
code download. SEQUENCE OF T1FlashControlEntry .1.3.6.1.4.1.335.1.2.1.3.6.1.4 |
t1FlashControlEntryEntry within the table specific to a particular T1 module/card
number for flash memory control. T1FlashControlEntry .1.3.6.1.4.1.335.1.2.1.3.6.1.4.1 |
t1FlashControlCardNumberIdentifies the T1 module/card number for flash memory control.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.6.1.4.1.1 |
t1FlashControlCommandControls the T1 module flash memory in preparation of a code
download. Perform a SET with the value eraseCardFlash to erase
the flash memory prior to downloading new T1 flash software.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.4.1.2 |
t1FlashControlFlashStatusIdentifies the status of the T1 module/card flash memory.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.1.4.1.3 |
e1-interface OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.6.2 |
e1L1InterfaceTableTable to configure the DS0 connections for the L1 interface
of an E1 module/card. SEQUENCE OF E1L1InterfaceEntry .1.3.6.1.4.1.335.1.2.1.3.6.2.1 |
e1L1InterfaceEntryEntry within the table specific to a particular DS0 channel
for the L1 interface of an E1 module/card. E1L1InterfaceEntry .1.3.6.1.4.1.335.1.2.1.3.6.2.1.1 |
e1L1InterfaceDS0IndexIdentifies the DS0 channel of the E1 module for configuration
of the L1 interface.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.6.2.1.1.1 |
e1L1InterfaceConnectionStateSelect the DS0 connection for DS0 configuration of the L1
interface. Available DS0 connections include Idle, Bypass,
CCM A1-A6, Data Port 1-2, Voice B1-B6 (on e1 card), Voice C1-C12,
and Voice D1-D12.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.1.1.2 |
e1L2InterfaceTableTable to configure the DS0 connections for the L2 interface
of an E1 module/card. SEQUENCE OF E1L2InterfaceEntry .1.3.6.1.4.1.335.1.2.1.3.6.2.2 |
e1L2InterfaceEntryEntry within the table specific to a particular DS0 channel
for the L2 interface of an E1 module/card. E1L2InterfaceEntry .1.3.6.1.4.1.335.1.2.1.3.6.2.2.1 |
e1L2InterfaceDS0IndexIdentifies the DS0 channel of the E1 module for configuration
of the L2 interface.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.6.2.2.1.1 |
e1L2InterfaceConnectionStateSelect the DS0 connection for DS0 configuration of the L2
interface. Available DS0 connections include Idle, Bypass,
CCM A1-A6, Data Port 1-2, Voice B1-B6 (on e1 card), Voice C1-C12,
and Voice D1-D12.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.2.1.2 |
e1CfgGroup OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.6.2.3 |
e1CfgL1LineCodeConfigures the L1 interface line coding method of the E1
module/card either to Alternate Mark Inversion (AMI) coding or
High Density Bipolar 3 (HDB3). AMI indicates that HDB3 zeros
suppression is not enabled. To obtain zeros suppression (bit
stuffing method) with AMI, you must also set the base rate of
the CCM and Data ports to 56Kbps. Otherwise, zeros suppression
will be the responsibility of the Data Terminal Equipment.
HDB3 does not allow more than three consecutive zeros. HDB3
format can be enabled only when supported by the connecting
equipment or the E1 service provider.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.1 |
e1CfgL1IdleCodeConfigures the idle code character of the L1 interface for
E1 module/card.rw OCTET STRING .1.3.6.1.4.1.335.1.2.1.3.6.2.3.2 |
e1CfgL1SignallingModeConfigures the signalling mode of the L1 interface for
E1 module/card.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.3 |
e1CfgL2LineCodeConfigures the L2 interface line coding method of the E1
module/card either to Alternate Mark Inversion (AMI) coding or
High Density Bipolar 3 (HDB3). AMI indicates that HDB3 zeros
suppression is not enabled. To obtain zeros suppression (bit
stuffing method) with AMI, you must also set the base rate of
the CCM and Data ports to 56Kbps. Otherwise, zeros suppression
will be the responsibility of the Data Terminal Equipment.
HDB3 does not allow more than three consecutive zeros. HDB3
format can be enabled only when supported by the connecting
equipment or the E1 service provider.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.4 |
e1CfgL2IdleCodeConfigures the idle code character of the L2 interface for
E1 module/card.rw OCTET STRING .1.3.6.1.4.1.335.1.2.1.3.6.2.3.5 |
e1CfgL2SignallingModeConfigures the signalling mode of the L2 interface for
E1 module/card.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.6 |
e1CfgDataPort1BaseRateSets the base rate of Data Port channel 1 on the E1 module.
The actual rate will be determined by the following formula:
rate of the data port = (base rate)*(number of DS0 channels).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.7 |
e1CfgDataPort1TimingSets how the clocking will be supplied for Data Port 1 on the
E1 module.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.8 |
e1CfgDataPort1DTRControlSets the DTR control for Data Port 1 on the E1 module. Option (1),
dtrNormal, will configure DTR control from the DTE equipment.
Option (2), dtrForced, will force DTR to a '1'.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.9 |
e1CfgDataPort1RTSControlSets the RTS control for Data Port 1 on the E1 module. Option (1),
rtsNormal, will configure RTS control from the DTE equipment.
Option (2), rtsForced, will force RTS to a '1'.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.10 |
e1CfgDataPort2BaseRateSets the base rate of Data Port channel 2 on the E1 module.
The actual rate will be determined by the following formula:
rate of the data port = (base rate)*(number of DS0 channels).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.11 |
e1CfgDataPort2TimingSets how the clocking will be supplied for Data Port 2 on the
E1 module.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.12 |
e1CfgDataPort2DTRControlSets the DTR control for Data Port 2 on the E1 module. Option (1),
dtrNormal, will configure DTR control from the DTE equipment.
Option (2), dtrForced, will force DTR to a '1'.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.13 |
e1CfgDataPort2RTSControlSets the RTS control for Data Port 2 on the E1 module. Option (1),
rtsNormal, will configure RTS control from the DTE equipment.
Option (2), rtsForced, will force RTS to a '1'.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.14 |
e1CfgCCMLinkA1RateSets the base rate of the CCM A1 channel for an E1 interface.
The actual rate will be determined by the following formula:
rate of the CCM port = (base rate)*(number of DS0 channels).rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.15 |
e1CfgCCMLinkA2RateSets the base rate of the CCM A2 channel for an E1 interface.
The actual rate will be determined by the following formula:
rate of the CCM port = (base rate)*(number of DS0 channels.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.16 |
e1CfgCCMLinkA3RateSets the base rate of the CCM A3 channel for an E1 interface.
The actual rate will be determined by the following formula:
rate of the CCM port = (base rate)*(number of DS0 channels.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.17 |
e1CfgCCMLinkA4RateSets the base rate of the CCM A4 channel for an E1 interface.
The actual rate will be determined by the following formula:
rate of the CCM port = (base rate)*(number of DS0 channels.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.18 |
e1CfgCCMLinkA5RateSets the base rate of the CCM A5 channel for an E1 interface.
The actual rate will be determined by the following formula:
rate of the CCM port = (base rate)*(number of DS0 channels.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.19 |
e1CfgCCMLinkA6RateSets the base rate of the CCM A6 channel for an E1 interface.
The actual rate will be determined by the following formula:
rate of the CCM port = (base rate)*(number of DS0 channels.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.20 |
e1CfgSystemClockSourceConfigures the source of the clock used in the E1 Access
Module. Options include:
- clockDerivedL1. The clock source is from the L1 interface.
- clockDerivedL2. The clock source is from the L2 interface.
- internalClocking. The clock is derived from a clock source
internal to the E1 Access Module.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.21 |
e1CfgL1Crc4Enables/Disables the CRC-4 mode for the L1 interface on the
E1 module.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.22 |
e1CfgL2Crc4Enables/Disables the CRC-4 mode for the L2 interface on the
E1 module.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.23 |
e1CfgL1ConfigThis object is a write only object that will signal the proxy to
start caching changes to the L1 ds0 connection tables. This is done to
solve an anomaly in the marathon/e1 design. The manager must set
this object to init before updating any of the e1L1InterfaceTable objects.
When all the changes have been set then this object will have to be set to
commit (2). The init will cause the proxy to upload the table from the marathon
and the commit will cause the proxy to send all the changes to the marathon.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.24 |
e1CfgL2ConfigThis object is a write only object that will signal the proxy to
start caching changes to the L2 ds0 connection tables. This is done to
solve an anomaly in the marathon/e1 design. The manager must set
this object to init before updating any of the e1L2InterfaceTable objects.
When all the changes have been set then this object will have to be set to
commit (2). The init will cause the proxy to upload the table from the marathon
and the commit will cause the proxy to send all the changes to the marathon.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.3.25 |
e1FlashControlTableTable to control (erase) E1 flash memory in preparation for a
code download. SEQUENCE OF E1FlashControlEntry .1.3.6.1.4.1.335.1.2.1.3.6.2.4 |
e1FlashControlEntryEntry within the table specific to a particular E1 module/card
number for flash memory control. E1FlashControlEntry .1.3.6.1.4.1.335.1.2.1.3.6.2.4.1 |
e1FlashControlCardNumberIdentifies the E1 module/card number for flash memory control.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.6.2.4.1.1 |
e1FlashControlCommandControls the E1 module flash memory in preparation of a code
download. Perform a SET with the value eraseCardFlash to erase
the flash memory prior to downloading new E1 flash software.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.4.1.2 |
e1FlashControlFlashStatusIdentifies the status of the E1 module/card flash memory.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.6.2.4.1.3 |
trap OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.7 |
trapAlarmEventReportingGroup OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.7.1 |
trapAlarmEventReportingAlarmsWhen enabled, displays the received alarms on command facility.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.7.1.1 |
trapAlarmEventReportingEventsWhen enabled, displays the received events on command facility.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.7.1.2 |
trapEventsCollectionIntervalPeriodic interval time between event collection poll cycles
(in minutes).rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.7.2 |
trapSubsTableTable to configure the recipients of the traps. SEQUENCE OF TrapSubsEntry .1.3.6.1.4.1.335.1.2.1.3.7.3 |
trapSubsEntryEntry within the table specifying each recipient. TrapSubsEntry .1.3.6.1.4.1.335.1.2.1.3.7.3.1 |
trapSubsIPAddressConfigures the IP address of the recipient station (manager).rw IpAddress .1.3.6.1.4.1.335.1.2.1.3.7.3.1.1 |
trapSubsCommunityStringConfigures the expected community string for the trap PDU to
be forwarded to the configured recipient.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.335.1.2.1.3.7.3.1.2 |
trapSubsActionAdds a new recipient or deletes an already configured recipient
from the subscription list.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.7.3.1.3 |
trapCfgAlarmEventsPortGroup OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.7.4 |
trapCfgTrapPortConfigures the destination for the output of alarms and events.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.7.4.1 |
trapCfgExtModemPriorityConfigures the priority for alarms and events sent to an external
modem.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.7.4.2 |
trapCfgExtAlarmRelayControls the external alarm relay on an NMS module.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.7.5 |
trapNodeNameIdentifies the name of the node that generated the trap. DisplayString (SNMPv2-TC) .1.3.6.1.4.1.335.1.2.1.3.7.6 |
trapCardNumberIdentifies the module/card number responsible for generating
the trap. INTEGER .1.3.6.1.4.1.335.1.2.1.3.7.7 |
trapChannelNumberIdentifies the port/channel number responsible for generating
the trap. INTEGER .1.3.6.1.4.1.335.1.2.1.3.7.8 |
trapFirstNodeNameIdentifies the source node name of the trap. DisplayString (SNMPv2-TC) .1.3.6.1.4.1.335.1.2.1.3.7.9 |
trapFirstCardNumberOrInternalFacilityIndicationThis identifies the card number that has generated the trap.
A value of 0FFh siginifies a special condition which identifies that the
trapChannelNumberOrInternalFacility object in the varBind contains
the type of internal facility. INTEGER .1.3.6.1.4.1.335.1.2.1.3.7.10 |
trapFirstChannelNumberOrInternalFacilityThis identifies the channel number that has generated the trap. If the
trapCardNumberOrInternalFacilityIndication object has a value of
0FFh then this objects identifies the internal facilities as $CMD if value
is 0, $PPP if the value is 1, and $DLD if the value is 2. INTEGER .1.3.6.1.4.1.335.1.2.1.3.7.11 |
trapSecondNodeNameIdentifies the destination node name of the trap. DisplayString (SNMPv2-TC) .1.3.6.1.4.1.335.1.2.1.3.7.12 |
trapSecondCardNumberOrInternalFacilityIndicationThis identifies the second card number that has generated the trap.
A value of 0FFh siginifies a special condition which identifies that the
trapChannelNumberOrInternalFacility object in the varBind contains
the type of internal facility. INTEGER .1.3.6.1.4.1.335.1.2.1.3.7.13 |
trapSecondChannelNumberOrInternalFacilityThis identifies the second channel number that has generated the trap.
If the trapCardNumberOrInternalFacilityIndication object has a value of
0ffh then this objects identifies the internal facilities as $CMD if
value is 0, $PPP if the value is 1, and $DLD if the value is 2. INTEGER .1.3.6.1.4.1.335.1.2.1.3.7.14 |
trapClassRequestedOrMatrixRequestThis identifies either the requested class number if the values are
between the allowable class number range (i.e. 1 to 64) or the matrix
request if the object value is 0. INTEGER .1.3.6.1.4.1.335.1.2.1.3.7.15 |
trapLinkTypeIdentifies the Link type associated with the trap. Enumeration .1.3.6.1.4.1.335.1.2.1.3.7.16 |
trapDLCINumberIdentifies the DLCI number associated with the trap corresponding
to a Frame Relay link. INTEGER .1.3.6.1.4.1.335.1.2.1.3.7.17 |
trapDLCIFirstLinkCardNumberIdentifies the module/card number associated with the trap
corresponding to a DLCI channel of the source Frame Relay link. INTEGER .1.3.6.1.4.1.335.1.2.1.3.7.18 |
trapDLCIFirstLinkChannelNumberIdentifies the port/channel number associated with the trap
corresponding to a DLCI channel of the source Frame Relay link. INTEGER .1.3.6.1.4.1.335.1.2.1.3.7.19 |
trapDLCIFirstLinkDLCINumberIdentifies the DLCI channel number associated with the trap
corresponding to the source Frame Relay link. INTEGER .1.3.6.1.4.1.335.1.2.1.3.7.20 |
trapDLCISecondLinkCardNumberIdentifies the port/channel number associated with the trap
corresponding to a DLCI channel of the destination Frame Relay link. INTEGER .1.3.6.1.4.1.335.1.2.1.3.7.21 |
trapDLCISecondLinkChannelNumberIdentifies the port/channel number associated with the trap
corresponding to a DLCI channel of the destination Frame Relay link. INTEGER .1.3.6.1.4.1.335.1.2.1.3.7.22 |
trapDLCISecondLinkDLCINumberIdentifies the DLCI channel number associated with the trap
corresponding to the destination Frame Relay link. INTEGER .1.3.6.1.4.1.335.1.2.1.3.7.23 |
proxy OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.3.8 |
pxyVersionNumberIdentifies the version number of the proxy agent installed.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.335.1.2.1.3.8.1 |
pxyCfgProxySwitchTo enable or disable the proxy agent operation on the
router module.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.8.2 |
pxyAddressMapTableNumberThe number of entries in the address map table. This will give
the highest numbered entry allocated.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.8.3 |
pxyAddressMapTableA table of all the MICOM Nodes this proxy is responsible for. SEQUENCE OF PxyAddressMapEntry .1.3.6.1.4.1.335.1.2.1.3.8.4 |
pxyAddressMapEntryAn entry that describes the network node which this proxy
agent manages. PxyAddressMapEntry .1.3.6.1.4.1.335.1.2.1.3.8.4.1 |
pxyAddressMapNodeNumberThe node number used to communicate with the device associated
with this entry.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.8.4.1.1 |
pxyAddressMapEntryStatusA code representing the current state of the table entry. This is
provided to define relationship within the table entry and to delete
and/or add devics to the Address Table. Default is notReadyrw Enumeration .1.3.6.1.4.1.335.1.2.1.3.8.4.1.2 |
pxyAddressMapNodeNameAndCommunityThe node name used to communicate with the device associated with
this entry. This unique name is also used to de-multiplex the proxy
managed nodes.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.8.4.1.3 |
pxyAddressMapChangeNodeNumberToIn order to change a node number of an existing node you must
use this entry with the NodeNumber entry being the existing node
number.rw INTEGER .1.3.6.1.4.1.335.1.2.1.3.8.4.1.4 |
pxySupportedVersionTableA table of sotware revision numbers this proxy agent support. SEQUENCE OF PxySupportedVersionEntry .1.3.6.1.4.1.335.1.2.1.3.8.5 |
pxySupportedVersionEntryAn entry that describes the version number of the software this
proxy agent supports. PxySupportedVersionEntry .1.3.6.1.4.1.335.1.2.1.3.8.5.1 |
pxySupportedIndexIdentifies the instance and hence the row of the entry in this table.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.8.5.1.1 |
pxySupportedVersionNumberIdentifies the Node Software Version number this proxy agent
understands and supports.ro Enumeration .1.3.6.1.4.1.335.1.2.1.3.8.5.1.2 |
pxyStatisticsLastNodeServedRepresent the last successul transaction between this proxy
agent and the foreign node.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.8.6 |
pxyStatisticsLastErrorNodeRepresent the last un-successful transaction of this proxy agent
and the foreign node.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.8.7 |
pxyStatisticsLastSNMPErrorThe SNMP error from the last transaction of this proxy agent with
the node referenced by pxyStatisticsLastErrorNode.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.8.8 |
pxyStatisticsLastErrorReturnCodeThe specific error code from the last transaction of this proxy
agent with the node referenced by pxyStatisticsLastErrorNode.ro INTEGER .1.3.6.1.4.1.335.1.2.1.3.8.9 |
pxyStatisticsTotalRequestsA count of requests received since the last reboot of the system.ro Counter .1.3.6.1.4.1.335.1.2.1.3.8.10 |
pxyStatisticsTotalInternalTrapsA count of internal Traps transmitted since the last reboot of
the system.ro Counter .1.3.6.1.4.1.335.1.2.1.3.8.11 |
pxyPPPTotalCountsA count of translated PPP requests transmitted to the managed nodes
since last reboot of the system.ro Counter .1.3.6.1.4.1.335.1.2.1.3.8.12 |
pxyPPPRejectCountsA count of rejected PPP requests transmitted to the managed nodes
since last reboot of the system.ro Counter .1.3.6.1.4.1.335.1.2.1.3.8.13 |
pxyCacheUpdateConfigures to force update the cached information maintained
in proxy agent.rw Enumeration .1.3.6.1.4.1.335.1.2.1.3.8.14 |
pxyNetworkAccessNodeNameThis is the name of the Integration unit that the
proxy is physically attached to. This node must already be
in the proxy's Address Map in order to set it here. This
NodeName is stored in the FileControlFile.Data file on the
host that the proxy is installed on.rw DisplayString .1.3.6.1.4.1.335.1.2.1.3.8.15 |
control OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.4 |
nodeResetGroup OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.4.1 |
nodeResetCodeResets the local node and configures to restart with the factory
default values or retain the current configuration; all channels
connected locally are also reset.rw Enumeration .1.3.6.1.4.1.335.1.2.1.4.1.1 |
nodeResetTypeConfigures to retstart with the current operational code or restart
and load the image from the flash.rw Enumeration .1.3.6.1.4.1.335.1.2.1.4.1.2 |
asyncResetTableTable to reset an async channel. SEQUENCE OF AsyncResetEntry .1.3.6.1.4.1.335.1.2.1.4.2 |
asyncResetEntryEntry within the table specifying particular channel on
specific module/card. AsyncResetEntry .1.3.6.1.4.1.335.1.2.1.4.2.1 |
asyncResetCardNumberIndicates the card/module number of the channel to be reset.ro INTEGER .1.3.6.1.4.1.335.1.2.1.4.2.1.1 |
asyncResetChannelNumberIdentifies the channel number to be reset.ro INTEGER .1.3.6.1.4.1.335.1.2.1.4.2.1.2 |
asyncResetCommandTriggers the reset operation.rw Enumeration .1.3.6.1.4.1.335.1.2.1.4.2.1.3 |
syncResetTableTable to reset a sync channel. SEQUENCE OF SyncResetEntry .1.3.6.1.4.1.335.1.2.1.4.3 |
syncResetEntryEntry within the table specifying particular channel on
specific module/card. SyncResetEntry .1.3.6.1.4.1.335.1.2.1.4.3.1 |
syncResetCardNumberIndicates the card/module number of the channel to be reset.ro INTEGER .1.3.6.1.4.1.335.1.2.1.4.3.1.1 |
syncResetChannelNumberIdentifies the channel number to be reset.ro INTEGER .1.3.6.1.4.1.335.1.2.1.4.3.1.2 |
syncResetCommandTriggers the reset operation.rw Enumeration .1.3.6.1.4.1.335.1.2.1.4.3.1.3 |
voiceResetTableTable to reset a voice channel. SEQUENCE OF VoiceResetEntry .1.3.6.1.4.1.335.1.2.1.4.4 |
voiceResetEntryEntry within the table specifying particular channel on
specific module/card. VoiceResetEntry .1.3.6.1.4.1.335.1.2.1.4.4.1 |
voiceResetCardNumberIndicates the card/module number of the channel to be reset.ro INTEGER .1.3.6.1.4.1.335.1.2.1.4.4.1.1 |
voiceResetChannelNumberIdentifies the channel number to be reset.ro INTEGER .1.3.6.1.4.1.335.1.2.1.4.4.1.2 |
voiceResetCommandTriggers the reset operation.rw Enumeration .1.3.6.1.4.1.335.1.2.1.4.4.1.3 |
linkResetTableTable to reset the links. Resetting a link clears all information
on the selected link. SEQUENCE OF LinkResetEntry .1.3.6.1.4.1.335.1.2.1.4.5 |
linkResetEntryEntry within the table for a specifying a particular link. LinkResetEntry .1.3.6.1.4.1.335.1.2.1.4.5.1 |
linkResetCardNumberIndicates the card/module number of the link to be reset.ro INTEGER .1.3.6.1.4.1.335.1.2.1.4.5.1.1 |
linkResetChannelNumberIdentifies the link/channel number to be reset.ro INTEGER .1.3.6.1.4.1.335.1.2.1.4.5.1.2 |
linkResetCommandTriggers the reset operation.rw Enumeration .1.3.6.1.4.1.335.1.2.1.4.5.1.3 |
clearLatchedAlarmsClears the latched alarm messages on the local node.rw Enumeration .1.3.6.1.4.1.335.1.2.1.4.6 |
pppLinkOperationGroup OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.4.7 |
pppLinkOperationActionCommand to resume normal operation of the $PPP link.
(Used for $PPP link debugging purposes.)rw Enumeration .1.3.6.1.4.1.335.1.2.1.4.7.1 |
pppLinkTimeOutActionCommand to disable the link timeout feature of the $PPP link.
(Used for $PPP link debugging purposes.)rw Enumeration .1.3.6.1.4.1.335.1.2.1.4.7.2 |
pppLinkDumpActionCommand to route rejected NMS commands to the log port for output.
(Used for $PPP link debugging purposes.)rw Enumeration .1.3.6.1.4.1.335.1.2.1.4.7.3 |
flashEPROMCommandCommand to erase flash memory on the CCM.rw Enumeration .1.3.6.1.4.1.335.1.2.1.4.8 |
voiceFlashEPROMTableTable to erase flash memory of voice modules. SEQUENCE OF VoiceFlashEPROMEntry .1.3.6.1.4.1.335.1.2.1.4.9 |
voiceFlashEPROMEntryEntry within the table specific to a particular voice channel
on a particular module/card for erasing flash memory. VoiceFlashEPROMEntry .1.3.6.1.4.1.335.1.2.1.4.9.1 |
voiceFlashEPROMCardNumberIdentifies the card number of the voice module
for erasing the flash memory.ro INTEGER .1.3.6.1.4.1.335.1.2.1.4.9.1.1 |
voiceFlashEPROMChannelNumberIdentifies the channel number of the voice module
for erasing the flash memory.ro INTEGER .1.3.6.1.4.1.335.1.2.1.4.9.1.2 |
voiceFlashEPROMCommandCommand to erase the flash memory of a particular voice
channel module.rw Enumeration .1.3.6.1.4.1.335.1.2.1.4.9.1.3 |
lanCardResetTableTable to reset the integral LAN module. SEQUENCE OF LanCardResetEntry .1.3.6.1.4.1.335.1.2.1.4.10 |
lanCardResetEntryEntry within the table to specify a particular card/module to
be reset. LanCardResetEntry .1.3.6.1.4.1.335.1.2.1.4.10.1 |
lanCardResetCardNumberIdentifies the module number to be reset.ro INTEGER .1.3.6.1.4.1.335.1.2.1.4.10.1.1 |
lanCardResetTypeCommands a specific type of reset for the integral Lan module.rw Enumeration .1.3.6.1.4.1.335.1.2.1.4.10.1.2 |
chControlTableTable controls the operating condition (status) of the channels
in the system. SEQUENCE OF ChControlEntry .1.3.6.1.4.1.335.1.2.1.4.11 |
chControlEntryEntry within the table specific to a particular channel on
specific module/card. ChControlEntry .1.3.6.1.4.1.335.1.2.1.4.11.1 |
chControlCardNumberIdentifies the card/module number of channel to be configured.ro INTEGER .1.3.6.1.4.1.335.1.2.1.4.11.1.1 |
chControlChannelNumberIdentifies the channel number to be configured.ro INTEGER .1.3.6.1.4.1.335.1.2.1.4.11.1.2 |
chControlCommandObject triggers the specified status action valid on the
channels. Option 1 returns a out-of-service async or voice/fax
port to the idle state. The option 2 permits to take an async or
voice/fax channel from idle state to out-of-service. Option 3
causes two selected (idle or out-of-service) ports to be connected.
The ports must be of like kind. An attempt to SET this Option
without first SET'ing the other required information
(chControlForceConnToNodeName, chControlForceConnToCard,
and chControlForceConnToChannel) will return an error.rw Enumeration .1.3.6.1.4.1.335.1.2.1.4.11.1.3 |
chControlForceConnToNodeNameThe node number of the other end of the channel to be
connected.rw DisplayString .1.3.6.1.4.1.335.1.2.1.4.11.1.4 |
chControlForceConnToCardThe module/card number of the other end of the channel
to be connected.rw INTEGER .1.3.6.1.4.1.335.1.2.1.4.11.1.5 |
chControlForceConnToChannelThe channel number of the other end of the channel to be
connected.rw INTEGER .1.3.6.1.4.1.335.1.2.1.4.11.1.6 |
frameRelayDLCIResetTableTable to reset the frame relay DLCI. SEQUENCE OF FrameRelayDLCIResetEntry .1.3.6.1.4.1.335.1.2.1.4.12 |
frameRelayDLCIResetEntryEntry within the table to specifying a particular DLCI on a
specific module and specific channel. FrameRelayDLCIResetEntry .1.3.6.1.4.1.335.1.2.1.4.12.1 |
frameRelayDLCIResetCardNumberIdentifies the card/module for the channel and associated DLCI.ro INTEGER .1.3.6.1.4.1.335.1.2.1.4.12.1.1 |
frameRelayDLCIResetChannelNumberIdentifies the channel number for the DLCI to be reset.ro INTEGER .1.3.6.1.4.1.335.1.2.1.4.12.1.2 |
frameRelayDLCIResetDLCINumberThis write-only object signfies the DLCI which is intended to
be reset. The card number and the channel number objects
identifies the proper instance of the particular linkrw INTEGER .1.3.6.1.4.1.335.1.2.1.4.12.1.3 |
frameRelayAllDLCIResetTableTable to reset all the configured DLCI on a particular frame
relay link. SEQUENCE OF FrameRelayAllDLCIResetEntry .1.3.6.1.4.1.335.1.2.1.4.13 |
frameRelayAllDLCIResetEntryEntry within the table specifying a particular channel/link. FrameRelayAllDLCIResetEntry .1.3.6.1.4.1.335.1.2.1.4.13.1 |
frameRelayAllDLCIResetCardNumberIdentifies the card/module for all the DLCIs to be reset.ro INTEGER .1.3.6.1.4.1.335.1.2.1.4.13.1.1 |
frameRelayAllDLCIResetChannelNumberIdentifies the channel/link for all the DLCIs to be reset.ro INTEGER .1.3.6.1.4.1.335.1.2.1.4.13.1.2 |
frameRelayAllDLCIResetCommandResets all the configured DLCI on a specific link/channel.rw Enumeration .1.3.6.1.4.1.335.1.2.1.4.13.1.3 |
t1e1CardResetTableTable to reset the T1/E1 module. SEQUENCE OF T1e1CardResetEntry .1.3.6.1.4.1.335.1.2.1.4.14 |
t1e1CardResetEntryEntry within the table specifying particular T1/E1 modle. T1e1CardResetEntry .1.3.6.1.4.1.335.1.2.1.4.14.1 |
t1e1CardResetCardNumberIdentifies the card/module number to be reset.ro INTEGER .1.3.6.1.4.1.335.1.2.1.4.14.1.1 |
t1e1CardResetCommandResets the module to either the current configuration (option 1)
or factory default values (option 2) .rw Enumeration .1.3.6.1.4.1.335.1.2.1.4.14.1.2 |
nvflashUpdateThis object is for platforms which use flash instead of CMOS for
configuration storage. These platforms update the configuration in
flash on a periodic basis rather than after each change. This object
will force an immediate configuration storage update.rw Enumeration .1.3.6.1.4.1.335.1.2.1.4.15 |
status OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.5 |
portTypeStatusTableIdentifies the type of all the channels/ports/links on a node. SEQUENCE OF PortTypeStatusEntry .1.3.6.1.4.1.335.1.2.1.5.1 |
portTypeStatusEntryEntry within the table specifying a particular channel. PortTypeStatusEntry .1.3.6.1.4.1.335.1.2.1.5.1.1 |
portTypeStatusCardNumberIdentifies the card/module number of the intended channel.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.1.1.1 |
portTypeStatusChannelNumberIdentifies the channel number.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.1.1.2 |
portTypeStatusChannelTypeIdentifies the channel/port/link type of the specified channel.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.1.1.3 |
asyncChStatusTableTable of EIA status for async channels. SEQUENCE OF AsyncChStatusEntry .1.3.6.1.4.1.335.1.2.1.5.2 |
asyncChStatusEntryEntry within the table specific to a particular async channel
on a module/card for EIA status. AsyncChStatusEntry .1.3.6.1.4.1.335.1.2.1.5.2.1 |
asyncChStatusCardNumberIdentifies the module/card number for EIA status of the async
channel.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.2.1.1 |
asyncChStatusChannelNumberIdentifies the async channel for EIA status.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.2.1.2 |
asyncChStatusEiaInputsRTSStatusIndicates the async channel EIA input status of the RTS signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.2.1.3 |
asyncChStatusEiaInputsDTRStatusIndicates the async channel EIA input status of the DTR signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.2.1.4 |
asyncChStatusEiaInputsUAStatusIndicates the async channel EIA input status of the UA signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.2.1.5 |
asyncChStatusEiaInputsBUSYStatusIndicates the async channel EIA input status of the Busy signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.2.1.6 |
asyncChStatusEiaOutputsRIStatusIndicates the async channel EIA output status of the RI signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.2.1.7 |
asyncChStatusEiaOutputsRLSDStatusIndicates the async channel EIA output status of the RLSD signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.2.1.8 |
asyncChStatusEiaOutputsCTSStatusIndicates the async channel EIA output status of the CTS signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.2.1.9 |
asyncChStatusEiaOutputsDSRStatusIndicates the async channel EIA output status of the DSR signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.2.1.10 |
syncChStatusTableTable of EIA status for sync channels. SEQUENCE OF SyncChStatusEntry .1.3.6.1.4.1.335.1.2.1.5.3 |
syncChStatusEntryEntry within the table specific to a particular sync channel
on a module/card for EIA status. SyncChStatusEntry .1.3.6.1.4.1.335.1.2.1.5.3.1 |
syncChStatusCardNumberIdentifies the module/card number for EIA status of the sync
channel.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.3.1.1 |
syncChStatusChannelNumberIdentifies the sync channel for EIA status.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.3.1.2 |
syncChStatusEiaInputsRTSStatusIndicates the sync channel EIA input status of the RTS signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.3.1.3 |
syncChStatusEiaInputsDTRStatusIndicates the sync channel EIA input status of the DTR signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.3.1.4 |
syncChStatusEiaInputsUAStatusIndicates the sync channel EIA input status of the UA signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.3.1.5 |
syncChStatusEiaInputsBUSYStatusIndicates the sync channel EIA input status of the Busy signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.3.1.6 |
syncChStatusEiaOutputsRIStatusIndicates the sync channel EIA output status of the RI signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.3.1.7 |
syncChStatusEiaOutputsRLSDStatusIndicates the sync channel EIA output status of the RLSD signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.3.1.8 |
syncChStatusEiaOutputsCTSStatusIndicates the sync channel EIA output status of the CTS signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.3.1.9 |
syncChStatusEiaOutputsDSRStatusIndicates the sync channel EIA output status of the DSR signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.3.1.10 |
voiceChStatusTableTable of voice channel status indicators. SEQUENCE OF VoiceChStatusEntry .1.3.6.1.4.1.335.1.2.1.5.4 |
voiceChStatusEntryEntry within the table specific to a particular voice channel
on a module/card for status indicators. VoiceChStatusEntry .1.3.6.1.4.1.335.1.2.1.5.4.1 |
voiceChStatusCardNumberIdentifies the module/card number of the voice channel
for status indications.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.4.1.1 |
voiceChStatusChannelNumberIdentifies the voice channel number for status indications.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.4.1.2 |
voiceChStatusInputLevelIndicates the level of the input signal monitored, in dBm.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.4.1.3 |
voiceChStatusStatusIndicates the mode of the current voice channel operation.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.4.1.4 |
voiceChStatusPromIDIndicates the Prom ID of the voice channel.ro DisplayString .1.3.6.1.4.1.335.1.2.1.5.4.1.5 |
voiceChStatusSoftwareRevisionIndicates the software revision of the voice channel.ro DisplayString .1.3.6.1.4.1.335.1.2.1.5.4.1.6 |
voiceChStatusTestModeIndicates the type of test that is currently running, if testing.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.4.1.7 |
voiceChStatusTestDSPResultIndicates the DSP test results of the voice channel following
initiation of a voice channel self test.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.4.1.8 |
voiceChStatusTestDataRAMResultIndicates the data RAM test results of the voice channel following
initiation of a voice channel self test.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.4.1.9 |
voiceChStatusTestCodeRAMResultIndicates the code RAM test results of the voice channel following
initiation of a voice channel self test.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.4.1.10 |
voiceChStatusTestAnalogHwResultIndicates the Analog Hardware test results of the voice channel
following initiation of a voice channel self test.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.4.1.11 |
voiceChStatusTestDeviceCfgResultIndicates the device configuration test results of the voice channel
following initiation of a voice channel self test.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.4.1.12 |
voiceChStatusFlashStateIndicates the state of the flash memory residing on the voice
channel.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.4.1.13 |
voiceChStatusEPROMStatusIndicates the status of the EPROM memory residing on the voice
channel.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.4.1.14 |
linkStatusTableTable of link channel status of the Integration unit. SEQUENCE OF LinkStatusEntry .1.3.6.1.4.1.335.1.2.1.5.5 |
linkStatusEntryEntry within the table specific to a particular channel
number on a module/card for status of the links. LinkStatusEntry .1.3.6.1.4.1.335.1.2.1.5.5.1 |
linkStatusCardNumberIdentifies the module/card number for link status.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.5.1.1 |
linkStatusChannelNumberIdentifies the port/channel number for link status.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.5.1.2 |
linkStatusLinkTypeIndicates the type of link configured on the Integration unit.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.5.1.3 |
linkStatusIntegralDevTypeIndicates the presence of an integral device on the Integration unit.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.5.1.4 |
linkStatusIntegralDevSlotNumberIndicates the location slot of the integral device, if present.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.5.1.5 |
linkStatusIntegralDeviceNumberIndicates the channel location of the integral device, if present.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.5.1.6 |
linkStatusStatusIndicates the status of the link.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.5.1.7 |
linkStatusNodeNumberIndicates the ID number of the remote linked Integration unit.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.5.1.8 |
linkStatusRemoteChannelNumberIndicates the channel number of the remote linked Integration
unit.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.5.1.9 |
linkStatusRemoteCardNumberIndicates the module/card number of the remote linked Integration
unit.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.5.1.10 |
linkStatusEiaOutputsRTSStatusIndicates the link channel EIA output status of the RTS signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.5.1.11 |
linkStatusEiaOutputsDTRStatusIndicates the link channel EIA output status of the DTR signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.5.1.12 |
linkStatusEiaOutputsBUSYStatusIndicates the link channel EIA output status of the Busy signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.5.1.13 |
linkStatusEiaOutputsUAStatusIndicates the link channel EIA output status of the UA signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.5.1.14 |
linkStatusEiaInputsRLSDStatusIndicates the link channel EIA output status of the RLSD signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.5.1.15 |
linkStatusEiaInputsDSRStatusIndicates the link channel EIA input status of the DSR signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.5.1.16 |
linkStatusEiaInputsRIStatusIndicates the link channel EIA input status of the RI signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.5.1.17 |
linkStatusEiaInputsCTSStatusIndicates the link channel EIA input status of the CTS signal.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.5.1.18 |
frameRelayLinkDLCIStatusTableTable of Frame Relay link status of DLCI channels. SEQUENCE OF FrameRelayLinkDLCIStatusEntry .1.3.6.1.4.1.335.1.2.1.5.6 |
frameRelayLinkDLCIStatusEntryEntry within the table specific to a particular DLCI channel,
FR access port/channel, and module/card number for FR link status. FrameRelayLinkDLCIStatusEntry .1.3.6.1.4.1.335.1.2.1.5.6.1 |
frameRelayLinkDLCIStatusCardNumberIdentifies the module/card number for FR link status of DLCI
channels.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.6.1.1 |
frameRelayLinkDLCIStatusChannelNumberIdentifies the port/channel number of the FR access link for
DLCI channel status.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.6.1.2 |
frameRelayLinkDLCIStatusDLCINumberIdentifies the DLCI channel number for FR link status.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.6.1.3 |
frameRelayLinkDLCIStatusNumberOfDLCIsIndicates the number of DLCIs for a particular FR access link.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.6.1.4 |
frameRelayLinkDLCIStatusConfOnMarathonIndicates whether or not the DLCI channel is configured by
the Integration unit.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.6.1.5 |
frameRelayLinkDLCIStatusReportedByPBXIndicates whether or not the DLCI channel is reported by
a PBX system.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.6.1.6 |
frameRelayLinkDLCIStatusActiveIndicates the status of the DLCI channel; active or not.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.6.1.7 |
frameRelayLinkDLCIStatusLinkStatusIndicates the status of the FR link for the specific DLCI channel.
Note: Transparent and Fragmented DLCI channel types will indicate
'down'.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.6.1.8 |
frameRelayLinkDLCIStatusUpConnectedNodeNumberIndicates the node ID # of the remote linked Integration unit.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.6.1.9 |
frameRelayLinkDLCIStatusUpConnectedChannelNumberIndicates the port/channel number of the FR access link of the
remote linked Integration unit.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.6.1.10 |
frameRelayLinkDLCIStatusUpConnectedCardNumberIndicates the module/card number of the FR access link of the
remote linked Integration unit.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.6.1.11 |
frameRelayLinkDLCIStatusUpRemoteDLCINumberIndicates the DLCI number of the remote linked Integration unit.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.6.1.12 |
chConnectionStatusTableTable of channel connection status indications. SEQUENCE OF ChConnectionStatusEntry .1.3.6.1.4.1.335.1.2.1.5.7 |
chConnectionStatusEntryEntry within the table specific to a particular channel number
on a module/card for connection status indications. ChConnectionStatusEntry .1.3.6.1.4.1.335.1.2.1.5.7.1 |
chConnectionStatusCardNumberIdentifies the module/card number of the channel for connection
status indication.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.7.1.1 |
chConnectionStatusChannelNumberIdentifies the channel number for connection status indication.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.7.1.2 |
chConnectionStatusChannelStatusIndicates the connection status of the channel.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.7.1.3 |
chConnectionStatusConnectedToNodeIndicates the node ID # of the destination channel connection, if any.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.7.1.4 |
chConnectionStatusConnectedToChannelIndicates the destination channel number of the connection, if any.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.7.1.5 |
chConnectionStatusConnectedToCardIndicates the destination module/card number of the connection, if any.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.7.1.6 |
chConnectionStatusConnectedToInternalFacilityIndicates a channel connection to an internal facility ($CMD or $PPP),
if any.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.7.1.7 |
remoteNodeStatusTableTable of remote nodes in the MICOM Integration unit network. SEQUENCE OF RemoteNodeStatusEntry .1.3.6.1.4.1.335.1.2.1.5.8 |
remoteNodeStatusEntryEntry within the table specific to each indexed node in the
MICOM Integration unit network. RemoteNodeStatusEntry .1.3.6.1.4.1.335.1.2.1.5.8.1 |
remoteNodeStatusIndexIdentifies the index for the table of remote nodes
in the MICOM Integration unit network.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.8.1.1 |
remoteNodeStatusNameIndicates the remote node name in the MICOM Integration
unit network.ro DisplayString .1.3.6.1.4.1.335.1.2.1.5.8.1.2 |
remoteNodeStatusTypeIndicates the type of remote node in the MICOM Integration
unit network.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.8.1.3 |
remoteNodeStatusNumberIndicates the node ID # of the remote node in the MICOM Integration
unit network.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.8.1.4 |
classStatusTableTable of switching classes defined for the Integration unit. SEQUENCE OF ClassStatusEntry .1.3.6.1.4.1.335.1.2.1.5.9 |
classStatusEntryEntry within the table specific to each indexed class defined for
the Integration unit. ClassStatusEntry .1.3.6.1.4.1.335.1.2.1.5.9.1 |
classStatusCfgClassIndexIdentifies the index for the table of defined switching classes
for the Integration unit.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.9.1.1 |
classStatusCfgClassNumberIndicates the switching class numbers defined for the Integration
unit.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.9.1.2 |
classQueueStatusTableTable of connection class queue channels defined for the Integration
unit. SEQUENCE OF ClassQueueStatusEntry .1.3.6.1.4.1.335.1.2.1.5.10 |
classQueueStatusEntryEntry within the table specific to a particular class number
defined for the Integration unit. ClassQueueStatusEntry .1.3.6.1.4.1.335.1.2.1.5.10.1 |
classQueueStatusClassNumIdentifies the class number to index connection queue channels
for the Integration unit.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.10.1.1 |
classQueueStatusChCountIndicates the number of queue channels defined for a particular
class connection for the Integration unit.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.10.1.2 |
classChannelStatusTableTable to indicate current queue status of the configured classes.
Should all the class channels be busy when the channel request
a class, that channel is put in waiting queue on first-come,
first-serve basis. SEQUENCE OF ClassChannelStatusEntry .1.3.6.1.4.1.335.1.2.1.5.11 |
classChannelStatusEntryAn entry for a specified class number that indicates the current
location in the queue. ClassChannelStatusEntry .1.3.6.1.4.1.335.1.2.1.5.11.1 |
classChannelStatusClassNumIdentifies the class number for which the channels are in queue.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.11.1.1 |
classQueueStatusChannelIndexIdentifies all the channels in the queue for a particular class.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.11.1.2 |
classChannelStatusNodeThe node number of the channel waiting in the queue.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.11.1.3 |
classChannelStatusChannelThe port number of the channel waiting in the queue.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.11.1.4 |
classChannelStatusCardThe module/card number of the channel waiting in the queue.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.11.1.5 |
flashMemoryStatusTableTable of CCM flash memory status. SEQUENCE OF FlashMemoryStatusEntry .1.3.6.1.4.1.335.1.2.1.5.12 |
flashMemoryStatusEntryEntry within the table specific to a particular flash bank
(1 or 2) for flash memory status. FlashMemoryStatusEntry .1.3.6.1.4.1.335.1.2.1.5.12.1 |
flashMemoryStatusFlashNumberIdentifies the flash memory bank for status; 1 or 2.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.12.1.1 |
flashMemoryStatusFileHeaderSizeIndicates the size of the file header in flash memory.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.12.1.2 |
flashMemoryStatusFileTypeIndicates the type of data stored in the flash memory bank.ro Enumeration .1.3.6.1.4.1.335.1.2.1.5.12.1.3 |
flashMemoryStatusMarathonImageSizeIndicates the size of the Integration unit file image (following
the header).ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.12.1.4 |
flashMemoryStatusCreationHoursIndicates the Hours portion of the creation date/time of the
Integration unit binary image file.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.12.1.5 |
flashMemoryStatusCreationMinutesIndicates the Minutes portion of the creation date/time of the
Integration unit binary image file.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.12.1.6 |
flashMemoryStatusCreationSecondsIndicates the Seconds portion of the creation date/time of the
Integration unit binary image file.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.12.1.7 |
flashMemoryStatusCreationYearIndicates the Year portion of the creation date/time of the
Integration unit binary image file.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.12.1.8 |
flashMemoryStatusCreationMonthIndicates the Month portion of the creation date/time of the
Integration unit binary image file.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.12.1.9 |
flashMemoryStatusCreationDayIndicates the Day portion of the creation date/time of the
Integration unit binary image file.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.12.1.10 |
flashMemoryStatusImageChecksumIndicates the image checksum of the Integration unit image
file.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.12.1.11 |
flashMemoryStatusPromIDIndicates the Prom ID file identifier of the Integration unit
image file.ro DisplayString .1.3.6.1.4.1.335.1.2.1.5.12.1.12 |
chForceConnStatusTableTable of channel force connects status. Note that the
table will be incomplete for Digital Voice modules (DVM) if the
modules are not contiguous on the T1, E1, or Digital Voice Expansion
modules. (Ex. - B1, B2, B5; table will only show B1 and B2, not B5.) SEQUENCE OF ChForceConnStatusEntry .1.3.6.1.4.1.335.1.2.1.5.13 |
chForceConnStatusEntryEntry within the table specific to a particular channel number
and module/card number for channel force connection status. ChForceConnStatusEntry .1.3.6.1.4.1.335.1.2.1.5.13.1 |
chForceConnStatusCardNumberIdentifies the module/card number of the source channel for
channel force connection status.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.13.1.1 |
chForceConnStatusChannelNumberIdentifies the source channel number for channel force
connection status.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.13.1.2 |
chForceConnStatusNodeNumberIndicates the Node ID # of the source channel for
channel force connection status.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.13.1.3 |
chForceConnStatusToNodeNumberIndicates the Node ID # of the destination channel for
channel force connection status.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.13.1.4 |
chForceConnStatusToCardNumberIdentifies the module/card number of the destination channel
for channel force connection status.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.13.1.5 |
chForceConnStatusToChannelNumberIdentifies the destination channel number for channel force
connection status.ro INTEGER .1.3.6.1.4.1.335.1.2.1.5.13.1.6 |
statistics OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.6 |
statistics-configuration OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.6.1 |
sysPeriodicStatisticsReportGroup OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.6.1.1 |
sysPeriodicStatisticsReportIntervalTime interval (in minutes) to collect
data for a periodic statistics report.rw Enumeration .1.3.6.1.4.1.335.1.2.1.6.1.1.1 |
sysReportDestinationDestination for statistics reports to be routed.rw Enumeration .1.3.6.1.4.1.335.1.2.1.6.1.1.2 |
sysRemoteLogNodeNameRemote Marathon Node name for log output and
periodic statistics reports to be routed.rw DisplayString .1.3.6.1.4.1.335.1.2.1.6.1.2 |
lastPeriodicStatisticsTimeGroup OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.6.1.3 |
lastPeriodicStatisticsTimeMonthMonth portion of time stamp of last periodic
report stored by the Marathon Node.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.1.3.1 |
lastPeriodicStatisticsTimeDayDay portion of time stamp of last periodic
report stored by the Marathon Node.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.1.3.2 |
lastPeriodicStatisticsTimeHoursHours portion of time stamp of last periodic
report stored by the Marathon Node.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.1.3.3 |
lastPeriodicStatisticsTimeMinutesMinutes portion of time stamp of last periodic
report stored by the Marathon Node.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.1.3.4 |
lastPeriodicStatisticsTimeSecondsSeconds portion of time stamp of last periodic
report stored by the Marathon Node.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.1.3.5 |
switchStatisticsEnable/disable Switch statistics as part of the
system statistics periodic report. Switch statistics
are class number, name, number of connects, connect
failures, and max number in queue.rw Enumeration .1.3.6.1.4.1.335.1.2.1.6.1.4 |
statistics-periodic OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.6.2 |
chPeriodicStatisticsTableTable of channel statistics for periodic
statistics reports. (Sync & Async channels) SEQUENCE OF ChPeriodicStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.2.1 |
chPeriodicStatisticsEntryEntry within the table to specify a particular
channel on specific module/card. ChPeriodicStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.2.1.1 |
chPeriodicStatisticsCardNumberIdentifies the module/card number for the
channel specific to the periodic statistics
report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.1.1.1 |
chPeriodicStatisticsChannelNumberIdentifies the channel number specific to the
periodic statistics report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.1.1.2 |
chPeriodicStatisticsMonthMonth portion of the time stamp for the channel
periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.1.1.3 |
chPeriodicStatisticsDayDay portion of the time stamp for the channel
periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.1.1.4 |
chPeriodicStatisticsHoursHours portion of the time stamp for the channel
periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.1.1.5 |
chPeriodicStatisticsMinutesMinutes portion of the time stamp for the channel
periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.1.1.6 |
chPeriodicStatisticsSecondsSeconds portion of the time stamp for the channel
periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.1.1.7 |
chPeriodicStatisticsBuffUtilizationThe buffer utilization (percentage) of the specified
channel in the periodic statistics report. Valid only for
Async channels, always 0 for Sync channelsro Gauge .1.3.6.1.4.1.335.1.2.1.6.2.1.1.8 |
chPeriodicStatisticsChannelBusiedOutThe busied-out condition (yes/no) of the specified
channel in the periodic statistics report.ro Enumeration .1.3.6.1.4.1.335.1.2.1.6.2.1.1.9 |
chPeriodicStatisticsChannelInFlowControlThe flow control condition (yes/no = fcn of buffer utilizaton)
of the specified channel in the periodic statistics report.ro Enumeration .1.3.6.1.4.1.335.1.2.1.6.2.1.1.10 |
chVPeriodicStatisticsTableTable of voice channel statistics for periodic
statistics reports. SEQUENCE OF ChVPeriodicStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.2.2 |
chVPeriodicStatisticsEntryEntry within the table to specify a particular voice
channel on specific voice module/card. ChVPeriodicStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.2.2.1 |
chVPeriodicStatisticsCardNumberIdentifies the voice module/card number for the
voice channel specific to the periodic statistics
report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.2.1.1 |
chVPeriodicStatisticsChannelNumberIdentifies the voice channel number specific to
the periodic statistics report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.2.1.2 |
chVPeriodicStatisticsMonthMonth portion of the time stamp for the voice
channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.2.1.3 |
chVPeriodicStatisticsDayDay portion of the time stamp for the voice
channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.2.1.4 |
chVPeriodicStatisticsHoursHours portion of the time stamp for the voice
channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.2.1.5 |
chVPeriodicStatisticsMinutesMinutes portion of the time stamp for the voice
channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.2.1.6 |
chVPeriodicStatisticsSecondsSeconds portion of the time stamp for the voice
channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.2.1.7 |
chVPeriodicStatisticsConnectTimeConnect time of the specified voice channel in
the periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.2.1.8 |
chVPeriodicStatisticsTotalCallsTotal calls recorded on the specified voice channel in
the periodic statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.2.2.1.9 |
chVPeriodicStatisticsAvgCallDurationAverage call duration of the specified voice channel in
the periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.2.1.10 |
chVPeriodicStatisticsBusyOutTimeBusy Out time of the specified voice channel in
the periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.2.1.11 |
chVPeriodicStatisticsNumOfCallAttemptsNumber of call attempts of the specified voice
channel in the periodic statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.2.2.1.12 |
chVPeriodicStatisticsDiscardedFrameCountsNumber of times voice frames were discarded on
the specified voice channel in the periodic
statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.2.2.1.13 |
chVPeriodicStatisticsTimeInFaxModeThe time spent in Fax mode of the specified voice
channel in the periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.2.1.14 |
chVPeriodicStatisticsPercentInFaxModeThe percentage of time spent in Fax mode of the
specified voice channel in the periodic statistics
report.ro Gauge .1.3.6.1.4.1.335.1.2.1.6.2.2.1.15 |
linkPeriodicStatisticsTableTable of link statistics for periodic statistics
reports. (all link types except Frame Relay) SEQUENCE OF LinkPeriodicStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.2.3 |
linkPeriodicStatisticsEntryEntry within the table to specify a particular link
channel on specific module/card. LinkPeriodicStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.2.3.1 |
linkPeriodicStatisticsCardNumberIdentifies the module/card number for the
link channel specific to the periodic statistics
report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.3.1.1 |
linkPeriodicStatisticsChannelNumberIdentifies the link channel number specific to
the periodic statistics report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.3.1.2 |
linkPeriodicStatisticsMonthMonth portion of the time stamp for the link
channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.3.1.3 |
linkPeriodicStatisticsDayDay portion of the time stamp for the link
channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.3.1.4 |
linkPeriodicStatisticsHoursHours portion of the time stamp for the link
channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.3.1.5 |
linkPeriodicStatisticsMinutesMinutes portion of the time stamp for the link
channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.3.1.6 |
linkPeriodicStatisticsSecondsSeconds portion of the time stamp for the link
channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.3.1.7 |
linkPeriodicStatisticsLinkTypeLink type of the specified link channel in
the periodic statistics report.ro Enumeration .1.3.6.1.4.1.335.1.2.1.6.2.3.1.8 |
linkPeriodicStatisticsTxFramesTransmitted frames (x100) of the specified link
channel in the periodic statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.2.3.1.9 |
linkPeriodicStatisticsRxFramesReceived frames (x100) of the specified link
channel in the periodic statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.2.3.1.10 |
linkPeriodicStatisticsLocCompositeUtilLocal composite utilization (percentage) of the
specified link channel in the periodic statistics
report.ro Gauge .1.3.6.1.4.1.335.1.2.1.6.2.3.1.11 |
linkPeriodicStatisticsRemCompositeUtilRemote composite utilization (percentage) of the
specified link channel in the periodic statistics
report.ro Gauge .1.3.6.1.4.1.335.1.2.1.6.2.3.1.12 |
linkPeriodicStatisticsLocBufferUtilLocal buffer utilization (percentage) of the
specified link channel in the periodic statistics
report.ro Gauge .1.3.6.1.4.1.335.1.2.1.6.2.3.1.13 |
linkPeriodicStatisticsRemBufferUtilRemote buffer utilization (percentage) of the
specified link channel in the periodic statistics
report.ro Gauge .1.3.6.1.4.1.335.1.2.1.6.2.3.1.14 |
linkPeriodicStatisticsLocRetransmitsLocal retransmits of the specified link channel
in the periodic statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.2.3.1.15 |
linkPeriodicStatisticsRemRetransmitsRemote retransmits of the specified link channel
in the periodic statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.2.3.1.16 |
linkPeriodicStatisticsLocLineAlarmsLocal line alarms of the specified link channel
in the periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.3.1.17 |
linkPeriodicStatisticsRemLineAlarmsRemote line alarms of the specified link channel
in the periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.3.1.18 |
linkPeriodicStatisticsLocTimeInSysFlowCtrlLocal time (seconds) in system flow control of the
specified link channel in the periodic statistics
report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.3.1.19 |
linkPeriodicStatisticsRemTimeInSysFlowCtrlRemote time (seconds) in system flow control of the
specified link channel in the periodic statistics
report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.3.1.20 |
linkPeriodicStatisticsLocTimeInSyncLossOrX21ConnectLocal time (seconds) in sync loss of the
specified link channel in the periodic statistics
report. (not used on X.21 links)ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.3.1.21 |
linkPeriodicStatisticsRemTimeInSyncLossRemote time (seconds) in sync loss of the
specified link channel in the periodic statistics
report. (not used on X.21 links)ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.3.1.22 |
linkPeriodicStatisticsLocTimeInCarrierLossLocal time (seconds) in carrier loss of the
specified link channel in the periodic statistics
report. (not used on X.21 links)ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.3.1.23 |
linkPeriodicStatisticsRemTimeInCarrierLossRemote time (seconds) in carrier loss of the
specified link channel in the periodic statistics
report. (not used on X.21 links)ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.3.1.24 |
linkFRPeriodicStatisticsTableTable of Frame Relay link statistics for periodic
statistics reports. (Note: More periodic FR link stats
are contained in table linkFRAccLnkPeriodicStatisticsTable.) SEQUENCE OF LinkFRPeriodicStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.2.4 |
linkFRPeriodicStatisticsEntryEntry within the table to specify a particular FR link
channel on specific module/card. LinkFRPeriodicStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.2.4.1 |
linkFRPeriodicStatisticsCardNumberIdentifies the module/card number for the FR
link channel specific to the periodic statistics
report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.4.1.1 |
linkFRPeriodicStatisticsChannelNumberIdentifies the FR link channel number specific to
the periodic statistics report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.4.1.2 |
linkFRPeriodicStatisticsMonthMonth portion of the time stamp for the FR link
channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.4.1.3 |
linkFRPeriodicStatisticsDayDay portion of the time stamp for the FR link
channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.4.1.4 |
linkFRPeriodicStatisticsHoursHours portion of the time stamp for the FR link
channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.4.1.5 |
linkFRPeriodicStatisticsMinutesMinutes portion of the time stamp for the FR link
channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.4.1.6 |
linkFRPeriodicStatisticsSecondsSeconds portion of the time stamp for the FR link
channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.4.1.7 |
linkFRPeriodicStatisticsCRCErrsCRC errors on the specified FR link access
channel in the periodic statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.2.4.1.8 |
linkFRPeriodicStatisticsLostStatusMsgCountsLost status messsage count of the specified FR
link channel in the periodic statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.2.4.1.9 |
linkFRPeriodicStatisticsStatusMsgProtocolErrsStatus message protocol errors of the specified FR
link channel in the periodic statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.2.4.1.10 |
linkFRPeriodicStatisticsNetworkResetsResets initiated by the network of the specified FR
link channel in the periodic statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.2.4.1.11 |
linkFRPeriodicStatisticsLinkResetsResets initiated by the Marathon of the specified FR
link channel in the periodic statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.2.4.1.12 |
linkFRPeriodicStatisticsNumOfDLCIsNumber of configured DLCIs for the specified FR
link channel in the periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.4.1.13 |
linkFRDLCIPeriodicStatisticsTableTable of Frame Relay link DLCI channel statistics for
periodic statistics reports. SEQUENCE OF LinkFRDLCIPeriodicStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.2.5 |
linkFRDLCIPeriodicStatisticsEntryEntry within the table to specify a particular FR link
channel on specific module/card for specific DLCI number. LinkFRDLCIPeriodicStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.2.5.1 |
linkFRDLCIPeriodicStatisticsCardNumberIdentifies the module/card number for the FR link
channel and DLCI number specific to the periodic
statistics report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.5.1.1 |
linkFRDLCIPeriodicStatisticsChannelNumberIdentifies the FR link channel number for the DLCI
number specific to the periodic statistics report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.5.1.2 |
linkFRDLCIPeriodicStatisticsDLCINumberIdentifies the DCLI number specific to
the periodic statistics report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.5.1.3 |
linkFRDLCIPeriodicStatisticsMonthMonth portion of the time stamp for the FR link
DLCI periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.5.1.4 |
linkFRDLCIPeriodicStatisticsDayDays portion of the time stamp for the FR link
DLCI periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.5.1.5 |
linkFRDLCIPeriodicStatisticsHoursHours portion of the time stamp for the FR link
DLCI periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.5.1.6 |
linkFRDLCIPeriodicStatisticsMinutesMinutes portion of the time stamp for the FR link
DLCI periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.5.1.7 |
linkFRDLCIPeriodicStatisticsSecondsSeconds portion of the time stamp for the FR link
DLCI periodic statistics report..ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.5.1.8 |
linkFRDLCIPeriodicStatisticsTxCharactersTransmitted character count of the specified DLCI
in the periodic statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.2.5.1.9 |
linkFRDLCIPeriodicStatisticsRxCharactersReceived character count of the specified DLCI
in the periodic statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.2.5.1.10 |
linkFRDLCIPeriodicStatisticsTxFramesTransmitted frames count of the specified DLCI
in the periodic statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.2.5.1.11 |
linkFRDLCIPeriodicStatisticsRxFramesReceived frames count of the specified DLCI
in the periodic statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.2.5.1.12 |
linkFRDLCIPeriodicStatisticsTimeActiveTime active (seconds) of the specified DLCI
in the periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.5.1.13 |
linkFRDLCIPeriodicStatisticsTimeCongestedForwardTime congested forward (seconds) of the specified
DLCI in the periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.5.1.14 |
linkFRDLCIPeriodicStatisticsTimeCongestedBackwardTime congested backward (seconds) of the specified
DLCI in the periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.5.1.15 |
swPeriodicStatisticsNumOfCurrentConnectsNumber of current connects for the periodic
statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.6 |
swPeriodicStatisticsTableTable of switch statistics for periodic
statistics reports. SEQUENCE OF SwPeriodicStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.2.7 |
swPeriodicStatisticsEntryEntry within the table to specify a particular
class number. SwPeriodicStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.2.7.1 |
swPeriodicStatisticsClassNumberIdentifies the class number for periodic statistics
report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.7.1.1 |
swPeriodicStatisticsMonthMonth portion of the time stamp for the switch
statistics periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.7.1.2 |
swPeriodicStatisticsDayDay portion of the time stamp for the switch
statistics periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.7.1.3 |
swPeriodicStatisticsHoursHours portion of the time stamp for the switch
statistics periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.7.1.4 |
swPeriodicStatisticsMinutesMinutes portion of the time stamp for the switch
statistics periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.7.1.5 |
swPeriodicStatisticsSecondsSeconds portion of the time stamp for the switch
statistics periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.7.1.6 |
swPeriodicStatisticsNumOfSuccessfulConnectsNumber of successful connects for the switch statistics
periodic statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.2.7.1.7 |
swPeriodicStatisticsNumOfUnsuccessfulAttemptsNumber of unsuccessful connects (attempts) for the
switch statistics periodic statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.2.7.1.8 |
swPeriodicStatisticsMaxNumInQueueMaximum number in the queue during report period
for the switch statistics periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.7.1.9 |
linkFRAccLnkPeriodicStatisticsTableTable of Frame Relay link access channel statistics for
periodic statistics reports. (Note: More periodic FR link
stats are contained in table linkFRPeriodicStatisticsTable.) SEQUENCE OF LinkFRPeriodicStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.2.8 |
linkFRAccLnkPeriodicStatisticsEntryEntry within the table to specify a particular FR link
access channel on specific module/card. LinkFRAccLnkPeriodicStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.2.8.1 |
linkFRAccLnkPeriodicStatisticsCardNumberIdentifies the module/card number for the FR link
access channel specific to the periodic statistics
report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.8.1.1 |
linkFRAccLnkPeriodicStatisticsChannelNumberIdentifies the FR link access channel number specific to
the periodic statistics report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.8.1.2 |
linkFRAccLnkPeriodicStatisticsMonthMonth portion of the time stamp for the FR link
access channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.8.1.3 |
linkFRAccLnkPeriodicStatisticsDayDay portion of the time stamp for the FR link
access channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.8.1.4 |
linkFRAccLnkPeriodicStatisticsHoursHours portion of the time stamp for the FR link
access channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.8.1.5 |
linkFRAccLnkPeriodicStatisticsMinutesMinutes portion of the time stamp for the FR link
access channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.8.1.6 |
linkFRAccLnkPeriodicStatisticsSecondsSeconds portion of the time stamp for the FR link
access channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.8.1.7 |
linkFRAccLnkPeriodicStatisticsLocalCompositeUtilizationLocal composite utilization (percentage) of the specified FR
link access channel in the periodic statistics report.ro Gauge .1.3.6.1.4.1.335.1.2.1.6.2.8.1.8 |
linkFRAccLnkPeriodicStatisticsLocalBufferUtilizationLocal buffer utilization (percentage) of the specified FR
link access channel in the periodic statistics report.ro Gauge .1.3.6.1.4.1.335.1.2.1.6.2.8.1.9 |
linkFRAccLnkPeriodicStatisticsLocalLineAlarmsLocal line alarms of the specified FR link access
channel in the periodic statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.2.8.1.10 |
linkFRAccLnkPeriodicStatisticsLocalSecInSysFlowControlLocal seconds in system flow control of the specified
FR link access channel in the periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.8.1.11 |
linkFRAccLnkPeriodicStatisticsLocalSecInSyncLossLocal seconds in sync loss of the specified FR link
access channel in the periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.8.1.12 |
linkFRAccLnkPeriodicStatisticsLocalSecInCarrierLossLocal seconds in carrier loss of the specified
FR link access channel in the periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.2.8.1.13 |
statistics-accumulated OBJECT IDENTIFIER .1.3.6.1.4.1.335.1.2.1.6.3 |
chAccumStatisticsTableTable of channel statistics for accumlulated
statistics reports. (Sync & Async channels). SEQUENCE OF ChAccumStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.3.1 |
chAccumStatisticsEntryEntry within the table to specify a particular
channel on specific module/card. ChAccumStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.3.1.1 |
chAccumStatisticsCardNumberIdentifies the module/card number for the
channel specific to the accumulated statistics
report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.1.1.1 |
chAccumStatisticsChannelNumberIdentifies the channel number specific to the
accumulated statistics report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.1.1.2 |
chAccumStatisticsMonthMonth portion of the time stamp for the channel
accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.1.1.3 |
chAccumStatisticsDayDay portion of the time stamp for the channel
accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.1.1.4 |
chAccumStatisticsHoursHours portion of the time stamp for the channel
accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.1.1.5 |
chAccumStatisticsMinutesMinutes portion of the time stamp for the channel
accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.1.1.6 |
chAccumStatisticsSecondsSeconds portion of the time stamp for the channel
accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.1.1.7 |
chAccumStatisticsBuffUtilizationThe buffer utilization (percentage) of the specified
channel in the accumulated statistics report. Valid only for
Async channels, always 0 for Sync channelsro Gauge .1.3.6.1.4.1.335.1.2.1.6.3.1.1.8 |
chAccumStatisticsChannelBusiedOutThe busied-out condition (yes/no) of the specified
channel in the accumulated statistics report.ro Enumeration .1.3.6.1.4.1.335.1.2.1.6.3.1.1.9 |
chAccumStatisticsChannelInFlowControlThe flow control condition (yes/no = fcn of buffer utilizaton)
of the specified channel in the accumulated statistics report.ro Enumeration .1.3.6.1.4.1.335.1.2.1.6.3.1.1.10 |
chVAccumStatisticsTableTable of voice channel statistics for accumulated
statistics reports. SEQUENCE OF ChVAccumStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.3.2 |
chVAccumStatisticsEntryEntry within the table to specify a particular voice
channel on specific voice module/card. ChVAccumStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.3.2.1 |
chVAccumStatisticsCardNumberIdentifies the voice module/card number for the
voice channel specific to the accumulated statistics
report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.2.1.1 |
chVAccumStatisticsChannelNumberIdentifies the voice channel number specific to
the accumulated statistics report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.2.1.2 |
chVAccumStatisticsMonthMonth portion of the time stamp for the voice
channel accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.2.1.3 |
chVAccumStatisticsDayDay portion of the time stamp for the voice
channel accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.2.1.4 |
chVAccumStatisticsHoursHours portion of the time stamp for the voice
channel accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.2.1.5 |
chVAccumStatisticsMinutesMinutes portion of the time stamp for the voice
channel accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.2.1.6 |
chVAccumStatisticsSecondsSeconds portion of the time stamp for the voice
channel accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.2.1.7 |
chVAccumStatisticsConnectTimeConnect time of the specified voice channel in
the accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.2.1.8 |
chVAccumStatisticsTotalCallsTotal calls recorded on the specified voice channel in
the accumulated statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.3.2.1.9 |
chVAccumStatisticsAvgCallDurationAverage call duration of the specified voice channel in
the accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.2.1.10 |
chVAccumStatisticsBusyOutTimeBusy Out time of the specified voice channel in
the accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.2.1.11 |
chVAccumStatisticsNumOfCallAttemptsNumber of call attempts of the specified voice
channel in the accumulated statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.3.2.1.12 |
chVAccumStatisticsDiscardedFrameCountsNumber of times voice frames were discarded on
the specified voice channel in the accumulated
statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.3.2.1.13 |
chVAccumStatisticsTimeInFaxModeThe time spent in Fax mode of the specified voice
channel in the accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.2.1.14 |
chVAccumStatisticsPercentInFaxModeThe percentage of time spent in Fax mode of the
specified voice channel in the accumulated statistics
report.ro Gauge .1.3.6.1.4.1.335.1.2.1.6.3.2.1.15 |
linkAccumStatisticsTableTable of link statistics for accumulated statistics
reports. (all link types except Frame Relay). SEQUENCE OF LinkAccumStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.3.3 |
linkAccumStatisticsEntryEntry within the table to specify a particular link
channel on specific module/card. LinkAccumStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.3.3.1 |
linkAccumStatisticsCardNumberIdentifies the module/card number for the
link channel specific to the accumulated statistics
report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.3.1.1 |
linkAccumStatisticsChannelNumberIdentifies the link channel number specific to
the accumulated statistics report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.3.1.2 |
linkAccumStatisticsMonthMonth portion of the time stamp for the link
channel accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.3.1.3 |
linkAccumStatisticsDayDay portion of the time stamp for the link
channel accumulated statistics report..ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.3.1.4 |
linkAccumStatisticsHoursHours portion of the time stamp for the link
channel accumulated statistics report..ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.3.1.5 |
linkAccumStatisticsMinutesMinutes portion of the time stamp for the link
channel accumulated statistics report..ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.3.1.6 |
linkAccumStatisticsSecondsSeconds portion of the time stamp for the link
channel accumulated statistics report..ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.3.1.7 |
linkAccumStatisticsLinkTypeLink type of the specified link channel in
the accumulated statistics report.ro Enumeration .1.3.6.1.4.1.335.1.2.1.6.3.3.1.8 |
linkAccumStatisticsTxFramesTransmitted frames (x100) of the specified link
channel in the accumulated statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.3.3.1.9 |
linkAccumStatisticsRxFramesReceived frames (x100) of the specified link
channel in the accumulated statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.3.3.1.10 |
linkAccumStatisticsLocCompositeUtilLocal composite utilization (percentage) of the
specified link channel in the accumulated statistics
report.ro Gauge .1.3.6.1.4.1.335.1.2.1.6.3.3.1.11 |
linkAccumStatisticsRemCompositeUtilRemote composite utilization (percentage) of the
specified link channel in the accumulated statistics
report.ro Gauge .1.3.6.1.4.1.335.1.2.1.6.3.3.1.12 |
linkAccumStatisticsLocBufferUtilLocal buffer utilization (percentage) of the
specified link channel in the accumulated statistics
report.ro Gauge .1.3.6.1.4.1.335.1.2.1.6.3.3.1.13 |
linkAccumStatisticsRemBufferUtilRemote buffer utilization (percentage) of the
specified link channel in the accumulated statistics
report.ro Gauge .1.3.6.1.4.1.335.1.2.1.6.3.3.1.14 |
linkAccumStatisticsLocRetransmitsLocal retransmits of the specified link channel
in the accumulated statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.3.3.1.15 |
linkAccumStatisticsRemRetransmitsRemote retransmits of the specified link channel
in the accumulated statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.3.3.1.16 |
linkAccumStatisticsLocLineAlarmsLocal line alarms of the specified link channel
in the accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.3.1.17 |
linkAccumStatisticsRemLineAlarmsRemote line alarms of the specified link channel
in the accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.3.1.18 |
linkAccumStatisticsLocTimeInSysFlowCtrlLocal time (seconds) in system flow control of the
specified link channel in the accumulated statistics
report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.3.1.19 |
linkAccumStatisticsRemTimeInSysFlowCtrlRemote time (seconds) in system flow control of the
specified link channel in the accumulated statistics
report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.3.1.20 |
linkAccumStatisticsLocTimeInSyncLossOrX21ConnectLocal time (seconds) in sync loss of the
specified link channel in the accumulated statistics
report. (not used on X.21 links).ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.3.1.21 |
linkAccumStatisticsRemTimeInSyncLossRemote time (seconds) in sync loss of the
specified link channel in the accumulated statistics
report. (not used on X.21 links)ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.3.1.22 |
linkAccumStatisticsLocTimeInCarrierLossLocal time (seconds) in carrier loss of the
specified link channel in the accumulated statistics
report. (not used on X.21 links)ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.3.1.23 |
linkAccumStatisticsRemTimeInCarrierLossRemote time (seconds) in carrier loss of the
specified link channel in the accumulated statistics
report. (not used on X.21 links)ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.3.1.24 |
linkFRAccumStatisticsTableTable of Frame Relay link statistics for accumulated
statistics reports. (Note: More accumulated FR link stats
are contained in table linkFRAccLnkAccumStatisticsTable.) SEQUENCE OF LinkFRAccumStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.3.4 |
linkFRAccumStatisticsEntryEntry within the table to specify a particular FR link
channel on specific module/card. LinkFRAccumStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.3.4.1 |
linkFRAccumStatisticsCardNumberIdentifies the module/card number for the FR
link channel specific to the accumulated statistics
report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.4.1.1 |
linkFRAccumStatisticsChannelNumberIdentifies the FR link channel number specific to
the accumulated statistics report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.4.1.2 |
linkFRAccumStatisticsMonthMonth portion of the time stamp for the FR link
channel accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.4.1.3 |
linkFRAccumStatisticsDayDay portion of the time stamp for the FR link
channel accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.4.1.4 |
linkFRAccumStatisticsHoursHours portion of the time stamp for the FR link
channel accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.4.1.5 |
linkFRAccumStatisticsMinutesMinutes portion of the time stamp for the FR link
channel accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.4.1.6 |
linkFRAccumStatisticsSecondsSeconds portion of the time stamp for the FR link
channel accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.4.1.7 |
linkFRAccumStatisticsCRCErrsCRC errors on the specified FR link access
channel in the accumulated statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.3.4.1.8 |
linkFRAccumStatisticsLostStatusMsgCountsLost status messsage count of the specified FR
link channel in the accumulated statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.3.4.1.9 |
linkFRAccumStatisticsStatusMsgProtocolErrsStatus message protocol errors of the specified FR
link channel in the accumulated statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.3.4.1.10 |
linkFRAccumStatisticsNetworkResetsResets initiated by the network of the specified FR
link channel in the accumulated statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.3.4.1.11 |
linkFRAccumStatisticsLinkResetsResets initiated by the Marathon of the specified FR
link channel in the accumulated statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.3.4.1.12 |
linkFRAccumStatisticsNumOfDLCIsNumber of configured DLCIs for the specified FR
link channel in the accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.4.1.13 |
linkFRDLCIAccumStatisticsTableTable of Frame Relay link DLCI channel statistics for
accumulated statistics reports. SEQUENCE OF LinkFRDLCIAccumStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.3.5 |
linkFRDLCIAccumStatisticsEntryEntry within the table to specify a particular FR link
channel on specific module/card for specific DLCI number. LinkFRDLCIAccumStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.3.5.1 |
linkFRDLCIAccumStatisticsCardNumberIdentifies the module/card number for the FR link
channel and DLCI number specific to the accumulated
statistics report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.5.1.1 |
linkFRDLCIAccumStatisticsChannelNumberIdentifies the FR link channel number for the DLCI
number specific to the accumulated statistics report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.5.1.2 |
linkFRDLCIAccumStatisticsDLCINumberIdentifies the DCLI number specific to
the accumulated statistics report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.5.1.3 |
linkFRDLCIAccumStatisticsMonthMonth portion of the time stamp for the FR link
DLCI accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.5.1.4 |
linkFRDLCIAccumStatisticsDayDay portion of the time stamp for the FR link
DLCI accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.5.1.5 |
linkFRDLCIAccumStatisticsHoursHours portion of the time stamp for the FR link
DLCI accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.5.1.6 |
linkFRDLCIAccumStatisticsMinutesMinutes portion of the time stamp for the FR link
DLCI accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.5.1.7 |
linkFRDLCIAccumStatisticsSecondsSeconds portion of the time stamp for the FR link
DLCI accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.5.1.8 |
linkFRDLCIAccumStatisticsTxCharactersTransmitted character count of the specified DLCI
in the accumulated statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.3.5.1.9 |
linkFRDLCIAccumStatisticsRxCharactersReceived character count of the specified DLCI
in the accumulated statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.3.5.1.10 |
linkFRDLCIAccumStatisticsTxFramesTransmitted frames count of the specified DLCI
in the accumulated statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.3.5.1.11 |
linkFRDLCIAccumStatisticsRxFramesReceived frames count of the specified DLCI
in the accumulated statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.3.5.1.12 |
linkFRDLCIAccumStatisticsTimeActiveTime active (seconds) of the specified DLCI
in the accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.5.1.13 |
linkFRDLCIAccumStatisticsTimeCongestedForwardTime congested forward (seconds) of the specified
DLCI in the accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.5.1.14 |
linkFRDLCIAccumStatisticsTimeCongestedBackwardTime congested backward (seconds) of the specified
DLCI in the accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.5.1.15 |
swAccumStatisticsNumOfCurrentConnectsNumber of current connects for the accumulated
statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.3.6 |
swAccumStatisticsTableTable of switch statistics for accumulated
statistics reports. SEQUENCE OF SwAccumStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.3.7 |
swAccumStatisticsEntryEntry within the table to specify a particular
class number. SwAccumStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.3.7.1 |
swAccumStatisticsClassNumberIdentifies the class number for accumulated statistics
report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.7.1.1 |
swAccumStatisticsMonthMonth portion of the time stamp for the switch
statistics accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.7.1.2 |
swAccumStatisticsDayDay portion of the time stamp for the switch
statistics accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.7.1.3 |
swAccumStatisticsHoursHours portion of the time stamp for the switch
statistics accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.7.1.4 |
swAccumStatisticsMinutesMinutes portion of the time stamp for the switch
statistics accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.7.1.5 |
swAccumStatisticsSecondsSeconds portion of the time stamp for the switch
statistics accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.7.1.6 |
swAccumStatisticsNumOfSuccessfulConnectsNumber of successful connects for the switch statistics
accumulated statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.3.7.1.7 |
swAccumStatisticsNumOfUnsuccessfulAttemptsNumber of unsuccessful connects (attempts) for the
switch statistics accumulated statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.3.7.1.8 |
swAccumStatisticsMaxNumInQueueMaximum number in the queue during report period
for the switch statistics accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.7.1.9 |
linkFRAccLnkAccumStatisticsTableTable of Frame Relay link access channel statistics for
accumulated statistics reports. (Note: More accumulated FR link
stats are contained in table linkFRAccumStatisticsTable.) SEQUENCE OF LinkFRAccLnkAccumStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.3.8 |
linkFRAccLnkAccumStatisticsEntryEntry within the table to specify a particular FR link
access channel on specific module/card. LinkFRAccLnkAccumStatisticsEntry .1.3.6.1.4.1.335.1.2.1.6.3.8.1 |
linkFRAccLnkAccumStatisticsCardNumberIdentifies the module/card number for the FR link
access channel specific to the accumulated statistics
report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.8.1.1 |
linkFRAccLnkAccumStatisticsChannelNumberIdentifies the FR link access channel number specific to
the accumulated statistics report data.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.8.1.2 |
linkFRAccLnkAccumStatisticsMonthMonth portion of the time stamp for the FR link
access channel accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.8.1.3 |
linkFRAccLnkAccumStatisticsDayDay portion of the time stamp for the FR link
access channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.8.1.4 |
linkFRAccLnkAccumStatisticsHoursHours portion of the time stamp for the FR link
access channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.8.1.5 |
linkFRAccLnkAccumStatisticsMinutesMinutes portion of the time stamp for the FR link
access channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.8.1.6 |
linkFRAccLnkAccumStatisticsSecondsSeconds portion of the time stamp for the FR link
access channel periodic statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.8.1.7 |
linkFRAccLnkAccumStatisticsLocalCompositeUtilizationLocal composite utilization (percentage) of the specified FR
link access channel in the accumulated statistics report.ro Gauge .1.3.6.1.4.1.335.1.2.1.6.3.8.1.8 |
linkFRAccLnkAccumStatisticsLocalBufferUtilizationLocal composite utilization (percentage) of the specified FR
link access channel in the accumulated statistics report.ro Gauge .1.3.6.1.4.1.335.1.2.1.6.3.8.1.9 |
linkFRAccLnkAccumStatisticsLocalLineAlarmsLocal line alarms of the specified FR link access
channel in the accumulated statistics report.ro Counter .1.3.6.1.4.1.335.1.2.1.6.3.8.1.10 |
linkFRAccLnkAccumStatisticsLocalSecInSysFlowControlLocal seconds in system flow control of the specified
FR link access channel in the accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.8.1.11 |
linkFRAccLnkAccumStatisticsLocalSecInSyncLossLocal seconds in sync loss of the specified FR link
access channel in the accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.8.1.12 |
linkFRAccLnkAccumStatisticsLocalSecInCarrierLossLocal seconds in carrier loss of the specified
FR link access channel in the accumulated statistics report.ro INTEGER .1.3.6.1.4.1.335.1.2.1.6.3.8.1.13 |