MEF-SOAM-PM-MIB
AI MIB Summary
The MEF-SOAM-PM-MIB enables SNMP-based monitoring of Ethernet Service OAM performance metrics, specifically frame loss ratio, frame delay, and frame delay variation, across Maintenance Entity Groups (MEGs) defined by IEEE 802.1ag and MEF 35. It facilitates the collection of single-ended and dual-ended measurement data from Maintenance End Points (MEPs) to validate Service Level Agreement (SLA) compliance for Ethernet Virtual Connections (EVCs).
This MIB module contains the management objects for the management of Ethernet Services Operations, Administration and Maintenance for Performance Monitoring.
Copyright 2010, 2011, 2012 Metro Ethernet Forum All rights reserved.
****************************************************************************
Reference Overview
A number of base documents have been used to create the Textual Conventions MIB, the SOAM-PM MIB and SOAM-FM extension MIB. The following are the abbreviations for the baseline documents:
[CFM] refers to 'Connectivity Fault Management', IEEE 802.1ag-2007, December 2007 [MEF7.1] refers to MEF 7.1 'Phase 2 EMS-NMS Information Model', October 2009 [MEF17] refers to MEF 17 'Service OAM Requirements & Framework - Phase 1', April 2007 [MEF10.2.1] refers to MEF 10.2.1 'Ethernet Services Attributes Phase 2', January 2011 [MEF SOAM-PM] refers to MEF 35 'Service OAM Performance Monitoring Implementation Agreement', January 2012 [MEF SOAM-FM] refers to MEF 30 'Service OAM Fault Management Implementation Agreement', January 2011 [Q.840.1] refers to 'ITU-T Requirements and analysis for NMS-EMS management interface of Ethernet over Transport and Metro Ethernet Network (EoT/MEN)', March 2007 [Y.1731] refers to ITU-T Y.1731 'OAM functions and mechanisms for Ethernet based networks', February 2011
****************************************************************************
Abbreviations Used
Term Definition Availability Performance A measure of the percentage of time within a specified time interval during which the frame loss is small Backward OAM information sent from the Responder MEP to the Controller MEP. For LM it indicates the frame counts/loss from the Responder MEP to the Controller MEP. For DM is indicates the delay and delay variation from the Responder MEP to the Controller MEP. BSS Business Support System CCM Continuity Check Message CFM Connectivity Fault Management CHLI Consecutive High Loss Interval, a sequence of small time intervals contained in T, each with high frame loss ratio Controller MEP The Controller MEP initiates SOAM PDUs, and receives responses from the Responder MEP. CoS Class of Service DM Delay Measurement Dual-Ended A type of process where a MEP sends measurement information to a peer MEP that will perform the calculations. EMS Element Management System ETH-DM Ethernet Delay Measurement function ETH-LM Ethernet Loss Measurement function ETH-SLM Ethernet Synthetic Frame Loss Measurement function EVC Ethernet Virtual Connection FD Frame Delay FDR Frame Delay Range FLR Frame Loss Ratio FM Fault Management Forward OAM information sent from the Controller MEP to the Responder MEP. For LM it indicates the frame counts/loss from the Controller MEP to the Responder MEP. For DM is indicates the delay and delay variation from the Controller MEP to the Responder MEP. HLI High Loss Interval, a small time interval contained in T with a high frame loss ratio IEEE Institute of Electrical and Electronics Engineers IETF Internet Engineering Task Force IFDV Inter-Frame Delay Variation ITU-T International Telecommunication Union - Telecommunication Standardization Bureau LAN Local Area Network LM Loss Measurement MAC Media Access Control MA Maintenance Association (equivalent to a MEG) MD Maintenance Domain (equivalent to a OAM Domain in MEF 17) MD Level Maintenance Domain Level (equivalent to a MEG level) ME Maintenance Entity Measurement Bin A Measurement Bin is a counter that stores the number of performance measurements falling within a specified range, during a Measurement Interval Measurement Interval A period of time during which measurements are taken. Measurements initiated during one Measurement Interval are kept separate from measurements taken during other Measurement Intervals. It is important to note that this is different from T. MEF Metro Ethernet Forum MEG Maintenance Entity Group (equivalent to a MA) MEG Level Maintenance Entity Group Level (equivalent to MD Level) MEN Metro Ethernet Network MEP Maintenance Association End Point or MEG End Point MFD Mean Frame Delay MIB Management Information Base MIP Maintenance Domain Intermediate Point or MEG Intermediate Point MP Maintenance Point. One of either a MEP or a MIP NE Network Element NMS Network Management System OAM Operations, Administration, and Maintenance On-Demand OAM actions that are initiated via manual intervention for a limited time to carry out diagnostics. On-Demand OAM can result in singular or periodic OAM actions during the diagnostic time interval One-way A measurement performed in the forward or backward direction. For example from MEP A to MEP B or from MEP B to MEP A. OSS Operations Support System PDU Protocol Data Unit PM Performance Monitoring PM Function A MEP capability specified for performance monitoring purposes (e.g., Single-Ended Delay, Single-Ended Synthetic Loss) PM Session A PM Session is the application of a given PM Function between a given pair of MEPs and using a given CoS Frame Set over some (possibly indefinite) period of time. PM Solution A PM Solution is a set of related requirements that when implemented allow a given set of performance metrics to be measured using a given set of PM functions. PM Tool A generic term used to discuss the application of a PM Function. Proactive OAM actions that are carried on continuously to permit timely reporting of fault and/or performance status. Resiliency Performance The number of High Loss Intervals and Consecutive High Loss Intervals in T Responder MEP In a single-ended session, the Responder MEP receives SOAM PDUs, from the Controller MEP, and transmits a response to the Controller MEP. SOAM-PM RFC Request for Comment Service Frame An Ethernet frame transmitted across the UNI toward the Service Provider or an Ethernet frame transmitted across the UNI toward the Subscriber Single-Ended A type of process where a MEP sends a measurement request and the peer MEP replies with the requested information so the originating MEP can calculate the measurement. Sink MEP In a dual-ended session, the Sink MEP receives SOAM PDUs, from the Controller MEP and performs the performance calculations. SLM Synthetic Loss Measurement SNMP Simple Network Management Protocol SNMP Agent An SNMP entity containing one or more command responder and/or notification originator applications (along with their associated SNMP engine). Typically implemented in an NE. SNMP Manager An SNMP entity containing one or more command generator and/or notification receiver applications (along with their associated SNMP engine). Typically implemented in an EMS or NMS. SOAM Service OAM SOAM PDU Service OAM frame, or Protocol Data Unit. Specifically, those PDUs defined in [IEEE 802.1ag], [ITU-T Y.1731], or MEF specifications Synthetic Traffic SOAM traffic that emulates service traffic in order to measure the performance experience. Delay measurements must use synthetic traffic, because user traffic does not contain standardized timestamp fields. Other measurements, such as Frame Loss, may also use synthetic frames for certain advantages (e.g., ability to measure loss in multipoint services). T Time Interval for SLS Metrics. The time over which a Performance Metric is defined. T is at least as large as the Measurement Interval, and generally consists of multiple Measurement Intervals. TC Textual Conventions TLV Type Length Value, a method of encoding Objects Two-way A measurement of the performance of frames that flow from the Controller MEP to Responder MEP and back again. UML Unified Modeling Language UTC Coordinated Universal Time UNI User-to-Network Interface VLAN Virtual LAN
Main OID:
mefSoamPmMib.1.3.6.1.4.1.15007.1.3
319
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
319 total| Object Name |
|---|
mefSoamPmMibThis MIB module contains the management objects for the
management of Ethernet Services Operations, Administration
and Maintenance for Performance Monitoring.
Copyright 2010, 2011, 2012 Metro Ethernet Forum
All rights reserved.
****************************************************************************
Reference Overview
A number of base documents have been used to create the Textual Conventions
MIB, the SOAM-PM MIB and SOAM-FM extension MIB. The following are the
abbreviations for the baseline documents:
[CFM] refers to 'Connectivity Fault Management', IEEE 802.1ag-2007,
December 2007
[MEF7.1] refers to MEF 7.1 'Phase 2 EMS-NMS Information Model',
October 2009
[MEF17] refers to MEF 17 'Service OAM Requirements & Framework - Phase 1',
April 2007
[MEF10.2.1] refers to MEF 10.2.1 'Ethernet Services Attributes Phase 2',
January 2011
[MEF SOAM-PM] refers to MEF 35 'Service OAM Performance Monitoring
Implementation Agreement', January 2012
[MEF SOAM-FM] refers to MEF 30 'Service OAM Fault Management Implementation
Agreement', January 2011
[Q.840.1] refers to 'ITU-T Requirements and analysis for NMS-EMS
management interface of Ethernet over Transport and Metro Ethernet
Network (EoT/MEN)', March 2007
[Y.1731] refers to ITU-T Y.1731 'OAM functions and mechanisms for Ethernet
based networks', February 2011
****************************************************************************
Abbreviations Used
Term Definition
Availability Performance A measure of the percentage of time within a
specified time interval during which the frame loss is small
Backward OAM information sent from the Responder MEP to the Controller MEP. For
LM it indicates the frame counts/loss from the Responder MEP to the
Controller MEP. For DM is indicates the delay and delay variation
from the Responder MEP to the Controller MEP.
BSS Business Support System
CCM Continuity Check Message
CFM Connectivity Fault Management
CHLI Consecutive High Loss Interval, a sequence of small time intervals
contained in T, each with high frame loss ratio
Controller MEP The Controller MEP initiates SOAM PDUs, and receives responses
from the Responder MEP.
CoS Class of Service
DM Delay Measurement
Dual-Ended A type of process where a MEP sends measurement information to a peer
MEP that will perform the calculations.
EMS Element Management System
ETH-DM Ethernet Delay Measurement function
ETH-LM Ethernet Loss Measurement function
ETH-SLM Ethernet Synthetic Frame Loss Measurement function
EVC Ethernet Virtual Connection
FD Frame Delay
FDR Frame Delay Range
FLR Frame Loss Ratio
FM Fault Management
Forward OAM information sent from the Controller MEP to the Responder MEP.
For LM it indicates the frame counts/loss from the Controller MEP
to the Responder MEP. For DM is indicates the delay and delay
variation from the Controller MEP to the Responder MEP.
HLI High Loss Interval, a small time interval contained in T with a
high frame loss ratio
IEEE Institute of Electrical and Electronics Engineers
IETF Internet Engineering Task Force
IFDV Inter-Frame Delay Variation
ITU-T International Telecommunication Union - Telecommunication
Standardization Bureau
LAN Local Area Network
LM Loss Measurement
MAC Media Access Control
MA Maintenance Association (equivalent to a MEG)
MD Maintenance Domain (equivalent to a OAM Domain in MEF 17)
MD Level Maintenance Domain Level (equivalent to a MEG level)
ME Maintenance Entity
Measurement Bin A Measurement Bin is a counter that stores the number of
performance measurements falling within a specified range, during
a Measurement Interval
Measurement Interval A period of time during which measurements are taken.
Measurements initiated during one Measurement Interval are kept
separate from measurements taken during other Measurement Intervals.
It is important to note that this is different from T.
MEF Metro Ethernet Forum
MEG Maintenance Entity Group (equivalent to a MA)
MEG Level Maintenance Entity Group Level (equivalent to MD Level)
MEN Metro Ethernet Network
MEP Maintenance Association End Point or MEG End Point
MFD Mean Frame Delay
MIB Management Information Base
MIP Maintenance Domain Intermediate Point or MEG Intermediate Point
MP Maintenance Point. One of either a MEP or a MIP
NE Network Element
NMS Network Management System
OAM Operations, Administration, and Maintenance On-Demand OAM actions that are initiated via manual intervention for a limited
time to carry out diagnostics. On-Demand OAM can result in
singular or periodic OAM actions during the diagnostic time
interval
One-way A measurement performed in the forward or backward direction. For
example from MEP A to MEP B or from MEP B to MEP A.
OSS Operations Support System
PDU Protocol Data Unit
PM Performance Monitoring
PM Function A MEP capability specified for performance monitoring purposes
(e.g., Single-Ended Delay, Single-Ended Synthetic Loss)
PM Session A PM Session is the application of a given PM Function between a given
pair of MEPs and using a given CoS Frame Set over some (possibly
indefinite) period of time.
PM Solution A PM Solution is a set of related requirements that when implemented
allow a given set of performance metrics to be measured using a
given set of PM functions.
PM Tool A generic term used to discuss the application of a PM Function.
Proactive OAM actions that are carried on continuously to permit timely reporting
of fault and/or performance status.
Resiliency Performance The number of High Loss Intervals and Consecutive High
Loss Intervals in T
Responder MEP In a single-ended session, the Responder MEP receives SOAM PDUs,
from the Controller MEP, and transmits a response to the
Controller MEP. SOAM-PM
RFC Request for Comment
Service Frame An Ethernet frame transmitted across the UNI toward the Service
Provider or an Ethernet frame transmitted across the UNI toward
the Subscriber
Single-Ended A type of process where a MEP sends a measurement request and the
peer MEP replies with the requested information so the originating
MEP can calculate the measurement.
Sink MEP In a dual-ended session, the Sink MEP receives SOAM PDUs, from the
Controller MEP and performs the performance calculations.
SLM Synthetic Loss Measurement
SNMP Simple Network Management Protocol
SNMP Agent An SNMP entity containing one or more command responder and/or
notification originator applications (along with their associated
SNMP engine). Typically implemented in an NE.
SNMP Manager An SNMP entity containing one or more command generator and/or
notification receiver applications (along with their associated
SNMP engine). Typically implemented in an EMS or NMS.
SOAM Service OAM
SOAM PDU Service OAM frame, or Protocol Data Unit. Specifically, those PDUs
defined in [IEEE 802.1ag], [ITU-T Y.1731], or MEF specifications
Synthetic Traffic SOAM traffic that emulates service traffic in order to measure
the performance experience. Delay measurements must use synthetic
traffic, because user traffic does not contain standardized
timestamp fields. Other measurements, such as Frame Loss, may also
use synthetic frames for certain advantages (e.g., ability to
measure loss in multipoint services).
T Time Interval for SLS Metrics. The time over which a Performance
Metric is defined. T is at least as large as the Measurement
Interval, and generally consists of multiple Measurement
Intervals.
TC Textual Conventions
TLV Type Length Value, a method of encoding Objects
Two-way A measurement of the performance of frames that flow from the
Controller MEP to Responder MEP and back again.
UML Unified Modeling Language
UTC Coordinated Universal Time
UNI User-to-Network Interface
VLAN Virtual LAN MODULE-IDENTITY .1.3.6.1.4.1.15007.1.3 |
IMPORTSThis MIB module contains the management objects for the
management of Ethernet Services Operations, Administration
and Maintenance for Performance Monitoring.
Copyright 2010, 2011, 2012 Metro Ethernet Forum
All rights reserved.
****************************************************************************
Reference Overview
A number of base documents have been used to create the Textual Conventions
MIB, the SOAM-PM MIB and SOAM-FM extension MIB. The following are the
abbreviations for the baseline documents:
[CFM] refers to 'Connectivity Fault Management', IEEE 802.1ag-2007,
December 2007
[MEF7.1] refers to MEF 7.1 'Phase 2 EMS-NMS Information Model',
October 2009
[MEF17] refers to MEF 17 'Service OAM Requirements & Framework - Phase 1',
April 2007
[MEF10.2.1] refers to MEF 10.2.1 'Ethernet Services Attributes Phase 2',
January 2011
[MEF SOAM-PM] refers to MEF 35 'Service OAM Performance Monitoring
Implementation Agreement', January 2012
[MEF SOAM-FM] refers to MEF 30 'Service OAM Fault Management Implementation
Agreement', January 2011
[Q.840.1] refers to 'ITU-T Requirements and analysis for NMS-EMS
management interface of Ethernet over Transport and Metro Ethernet
Network (EoT/MEN)', March 2007
[Y.1731] refers to ITU-T Y.1731 'OAM functions and mechanisms for Ethernet
based networks', February 2011
****************************************************************************
Abbreviations Used
Term Definition
Availability Performance A measure of the percentage of time within a
specified time interval during which the frame loss is small
Backward OAM information sent from the Responder MEP to the Controller MEP. For
LM it indicates the frame counts/loss from the Responder MEP to the
Controller MEP. For DM is indicates the delay and delay variation
from the Responder MEP to the Controller MEP.
BSS Business Support System
CCM Continuity Check Message
CFM Connectivity Fault Management
CHLI Consecutive High Loss Interval, a sequence of small time intervals
contained in T, each with high frame loss ratio
Controller MEP The Controller MEP initiates SOAM PDUs, and receives responses
from the Responder MEP.
CoS Class of Service
DM Delay Measurement
Dual-Ended A type of process where a MEP sends measurement information to a peer
MEP that will perform the calculations.
EMS Element Management System
ETH-DM Ethernet Delay Measurement function
ETH-LM Ethernet Loss Measurement function
ETH-SLM Ethernet Synthetic Frame Loss Measurement function
EVC Ethernet Virtual Connection
FD Frame Delay
FDR Frame Delay Range
FLR Frame Loss Ratio
FM Fault Management
Forward OAM information sent from the Controller MEP to the Responder MEP.
For LM it indicates the frame counts/loss from the Controller MEP
to the Responder MEP. For DM is indicates the delay and delay
variation from the Controller MEP to the Responder MEP.
HLI High Loss Interval, a small time interval contained in T with a
high frame loss ratio
IEEE Institute of Electrical and Electronics Engineers
IETF Internet Engineering Task Force
IFDV Inter-Frame Delay Variation
ITU-T International Telecommunication Union - Telecommunication
Standardization Bureau
LAN Local Area Network
LM Loss Measurement
MAC Media Access Control
MA Maintenance Association (equivalent to a MEG)
MD Maintenance Domain (equivalent to a OAM Domain in MEF 17)
MD Level Maintenance Domain Level (equivalent to a MEG level)
ME Maintenance Entity
Measurement Bin A Measurement Bin is a counter that stores the number of
performance measurements falling within a specified range, during
a Measurement Interval
Measurement Interval A period of time during which measurements are taken.
Measurements initiated during one Measurement Interval are kept
separate from measurements taken during other Measurement Intervals.
It is important to note that this is different from T.
MEF Metro Ethernet Forum
MEG Maintenance Entity Group (equivalent to a MA)
MEG Level Maintenance Entity Group Level (equivalent to MD Level)
MEN Metro Ethernet Network
MEP Maintenance Association End Point or MEG End Point
MFD Mean Frame Delay
MIB Management Information Base
MIP Maintenance Domain Intermediate Point or MEG Intermediate Point
MP Maintenance Point. One of either a MEP or a MIP
NE Network Element
NMS Network Management System
OAM Operations, Administration, and Maintenance On-Demand OAM actions that are initiated via manual intervention for a limited
time to carry out diagnostics. On-Demand OAM can result in
singular or periodic OAM actions during the diagnostic time
interval
One-way A measurement performed in the forward or backward direction. For
example from MEP A to MEP B or from MEP B to MEP A.
OSS Operations Support System
PDU Protocol Data Unit
PM Performance Monitoring
PM Function A MEP capability specified for performance monitoring purposes
(e.g., Single-Ended Delay, Single-Ended Synthetic Loss)
PM Session A PM Session is the application of a given PM Function between a given
pair of MEPs and using a given CoS Frame Set over some (possibly
indefinite) period of time.
PM Solution A PM Solution is a set of related requirements that when implemented
allow a given set of performance metrics to be measured using a
given set of PM functions.
PM Tool A generic term used to discuss the application of a PM Function.
Proactive OAM actions that are carried on continuously to permit timely reporting
of fault and/or performance status.
Resiliency Performance The number of High Loss Intervals and Consecutive High
Loss Intervals in T
Responder MEP In a single-ended session, the Responder MEP receives SOAM PDUs,
from the Controller MEP, and transmits a response to the
Controller MEP. SOAM-PM
RFC Request for Comment
Service Frame An Ethernet frame transmitted across the UNI toward the Service
Provider or an Ethernet frame transmitted across the UNI toward
the Subscriber
Single-Ended A type of process where a MEP sends a measurement request and the
peer MEP replies with the requested information so the originating
MEP can calculate the measurement.
Sink MEP In a dual-ended session, the Sink MEP receives SOAM PDUs, from the
Controller MEP and performs the performance calculations.
SLM Synthetic Loss Measurement
SNMP Simple Network Management Protocol
SNMP Agent An SNMP entity containing one or more command responder and/or
notification originator applications (along with their associated
SNMP engine). Typically implemented in an NE.
SNMP Manager An SNMP entity containing one or more command generator and/or
notification receiver applications (along with their associated
SNMP engine). Typically implemented in an EMS or NMS.
SOAM Service OAM
SOAM PDU Service OAM frame, or Protocol Data Unit. Specifically, those PDUs
defined in [IEEE 802.1ag], [ITU-T Y.1731], or MEF specifications
Synthetic Traffic SOAM traffic that emulates service traffic in order to measure
the performance experience. Delay measurements must use synthetic
traffic, because user traffic does not contain standardized
timestamp fields. Other measurements, such as Frame Loss, may also
use synthetic frames for certain advantages (e.g., ability to
measure loss in multipoint services).
T Time Interval for SLS Metrics. The time over which a Performance
Metric is defined. T is at least as large as the Measurement
Interval, and generally consists of multiple Measurement
Intervals.
TC Textual Conventions
TLV Type Length Value, a method of encoding Objects
Two-way A measurement of the performance of frames that flow from the
Controller MEP to Responder MEP and back again.
UML Unified Modeling Language
UTC Coordinated Universal Time
UNI User-to-Network Interface
VLAN Virtual LAN NOTIFICATION-TYPE .1.3.6.1.4.1.15007.1.3 |
mefSoamPmNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.15007.1.3.0 |
mefSoamAvailabilityChangeAlarmAn mefSoamAvailabilityChangeAlarm notification is sent when the state of
mefSoamLmMeasuredStatsAvailForwardStatus or
mefSoamLmMeasuredStatsAvailBackwardStatus changes.
The management entity that receives the notification can identify
the system from the network source address of the notification,
and can identify the PM session reporting the change
by the indices in the OID
mefSoamLmMeasuredStatsAvailForwardLastTransitionTime, including
dot1agCfmMdIndex, dot1agCfmMaIndex, dot1agCfmMepIdentifier, and
mefSoamLmCfgIndex.
An agent is not to generate more than one mefSoamAvailabilityChangeAlarm
'notification-event' in a given time interval per PM session as
specified by the mefSoamPmNotificationCfgAlarmInterval. A
'notification-event' is the transmission of a single notification to
a list of notification destinations.
If additional availability state changes occur within the
mefSoamPmNotificationCfgAlarmInterval period, then notification
generation for these changes are suppressed by the agent until
the current alarm interval expires. At the end of an alarm interval
period, one notification-event is generated if any availability
state changes occurred since the start of the alarm interval period.
In such a case, another alarm interval period is started right away. NOTIFICATION-TYPE .1.3.6.1.4.1.15007.1.3.0.1 |
mefSoamLmSessionStartStopAlarmAn mefSoamLmSessionStartStopAlarm notification is sent when the state of
mefSoamLmCfgSessionStatus changes.
The management entity that receives the notification can identify
the system from the network source address of the notification,
and can identify the individual PM session reporting the start/stop
by the indices in the OID mefSoamLmCfgSessionStatus, including
dot1agCfmMdIndex, dot1agCfmMaIndex, dot1agCfmMepIdentifier, and
mefSoamLmCfgIndex.
An agent is not to generate more than one mefSoamLmSessionStartStopAlarm
'notification-event' in a given time interval per LM session as specified
by the mefSoamPmNotificationCfgAlarmInterval. A 'notification-event' is
the transmission of a single notification to a list of notification
destinations.
If additional operational state changes occur within the
mefSoamPmNotificationCfgAlarmInterval period, then notification
generation for these changes are be suppressed by the agent until
the current alarm interval expires. At the end of an alarm interval
period, one notification-event is generated if any operational
state changes occurred since the start of the alarm interval period. In
such a case, another alarm interval period is started right away. NOTIFICATION-TYPE .1.3.6.1.4.1.15007.1.3.0.2 |
mefSoamDmSessionStartStopAlarmAn mefSoamDmSessionStartStopAlarm notification is sent when the state of
mefSoamDmCfgSessionStatus changes.
The management entity that receives the notification can identify
the system from the network source address of the notification,
and can identify the individual PM session reporting the start/stop
by the indices in the OID mefSoamDmCfgSessionStatus, including
dot1agCfmMdIndex, dot1agCfmMaIndex, dot1agCfmMepIdentifier, and
mefSoamDmCfgIndex.
An agent is not to generate more than one mefSoamDmSessionStartStopAlarm
'notification-event' in a given time interval per DM session as specified
by mefSoamPmNotificationCfgAlarmInterval. A 'notification-event' is the
transmission of a single notification to a list of notification
destinations.
If additional operational state changes occur within the
mefSoamPmNotificationCfgAlarmInterval period, then notification generation
for these changes are suppressed by the agent until the current alarm
interval expires. At the end of an alarm interval period, one
notification-event is generated if any operational state changes
occurred since the start of the alarm interval period. In such a case,
another alarm interval period is started right away. NOTIFICATION-TYPE .1.3.6.1.4.1.15007.1.3.0.3 |
mefSoamPmThresholdCrossingAlarmAn mefSoamPmThresholdCrossingAlarm notification is sent if the
following conditions are met for a particular type.
For an aboveAlarm five conditions need to be met:
a) measurement of the parameter is enabled via mefSoamLmCfgMeasurementEnable
for a LM crossing or mefSoamDmCfgMeasurementEnable for a DM crossing;
and
b) the parameter threshold is configured in the mefSoamLmThresholdCfgTable
or mefSoamDmThresholdCfgTable; and
c) the threshold crossing type of bPmThresholdAboveAlarm is enabled;
and
d) the measured value of the parameter exceeds the value configured in
the mefSoamLmThresholdCfgTable for a LM crossing entry or
mefSoamDmThresholdCfgTable for a DM crossing entry for a type of
bPmThresholdAboveAlarm; and
e) no previous mefSoamPmThresholdCrossingAlarm notifications with type
aboveAlarm have been sent relating to the same threshold in the
mefSoamLmThresholdCfgTable or mefSoamDmThresholdCfgTable and the
same parameter, during this Measurement Interval.
For a setAlarm five conditions need to be met:
a) measurement of the parameter is enabled via mefSoamLmCfgMeasurementEnable
for a LM crossing or mefSoamDmCfgMeasurementEnable for a DM crossing;
and
b) the parameter threshold is configured in the mefSoamLmThresholdCfgTable
or mefSoamDmThresholdCfgTable; and
c) the threshold crossing type of bPmThresholdSetClearAlarm is enabled;
and
d) the measured value of the parameter exceeds the value configured in
the mefSoamLmThresholdCfgTable for a LM crossing entry or
mefSoamDmThresholdCfgTable for a DM crossing entry for a type of
bPmThresholdSetClearAlarm for the Measurement Interval; and
e) the previous measured value did not
exceed the value configured in the mefSoamLmThresholdCfgTable for
a LM crossing entry or mefSoamDmThresholdCfgTable for a DM crossing
entry for a type of bPmThresholdSetClearAlarm.
For a clearAlarm five conditions need to be met:
a) measurement of the parameter is enabled via mefSoamLmCfgMeasurementEnable
for a LM crossing or mefSoamDmCfgMeasurementEnable for a DM crossing;
and
b) the parameter threshold is configured in the mefSoamLmThresholdCfgTable
or mefSoamDmThresholdCfgTable; and
c) the threshold crossing type of bPmThresholdSetClearAlarm is enabled;
and
d) the measured value of the parameter did not exceed the value configured
in the mefSoamLmThresholdCfgTable for a LM crossing entry or
mefSoamDmThresholdCfgTable for a DM crossing entry for a type of
bPmThresholdSetClearAlarm for the Measurement Interval; and
e) the previous measured value did
exceed the value configured in the mefSoamLmThresholdCfgTable for
a LM crossing entry or mefSoamDmThresholdCfgTable for a DM crossing
entry for a type of bPmThresholdSetClearAlarm.
In the case of thresholds applied to a maximum or average measurement
counter, the previous measured value is the value of the counter at the
end of the preceding Measurement Interval. In the case of thresholds
applied to the last measured value, it is the previous measured value.
The management entity that receives the notification can identify
the system from the network source address of the notification,
and can identify the LM or DM session reporting the threshold
crossing by the indices in the mefSoamPmNotificationCfgThresholdId object,
including dot1agCfmMdIndex, dot1agCfmMaIndex, dot1agCfmMepIdentifier,
and the mefSoamLmCfgIndex or mefSoamDmCfgIndex.
An agent is not to generate more than one mefSoamLmThresholdCrossingAlarm
'notification-event' of a given type per LM or DM session as specified
by mefSoamPmNotificationCfgAlarmInterval. A 'notification-event' is the
transmission of a single notification to a list of notification
destinations.
If additional threshold crossing events occur within the
mefSoamPmNotificationCfgAlarmInterval period, then notification
generation for these changes are suppressed by the agent until
the current alarm interval expires. At the end of an alarm interval
period, one notification-event is generated if any threshold
crossing events occurred since the start of the alarm interval period.
In such a case, another alarm interval period is started right away. NOTIFICATION-TYPE .1.3.6.1.4.1.15007.1.3.0.4 |
mefSoamPmMibObjects OBJECT IDENTIFIER .1.3.6.1.4.1.15007.1.3.1 |
mefSoamPmMep OBJECT IDENTIFIER .1.3.6.1.4.1.15007.1.3.1.1 |
mefSoamPmMepTableThis table is an extension of the dot1agCfmMepTable and rows
are automatically added or deleted from this table based upon row
creation and destruction of the dot1agCfmMepTable.
This table represents the local MEP PM configuration table. The
primary purpose of this table is provide local parameters for the
SOAM PM function found in [Y.1731] and [MEF SOAM-PM] and instantiated
at a MEP. SEQUENCE OF MefSoamPmMepEntry .1.3.6.1.4.1.15007.1.3.1.1.1 |
mefSoamPmMepEntryThe conceptual row of mefSoamPmMepTable. MefSoamPmMepEntry .1.3.6.1.4.1.15007.1.3.1.1.1.1 |
mefSoamPmMepOperNextIndexThis object contains an unused value for a PM session number on a
MEP that can be used for either LM or DM sessions, or a zero to
indicate that none exist. This value needs to be read in order to
find an available index for row-creation of a PM session on a MEP and
then used when a row is created. This value is automatically updated
by the SNMP Agent after the row is created.
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never to be reused for other PM sessions on the same MEP while this
session is active, or until it wraps to zero. The index value keeps
increasing up to that time. This is to facilitate access control based
on a fixed index for an EMS, since the index is not reused.
This object is an extension of the dot1agCfmMepTable and the object is
automatically added or deleted based upon row creation and destruction
of the dot1agCfmMepTable.ro Dot1afCfmIndexIntegerNextFree (IEEE8021-CFM-MIB) .1.3.6.1.4.1.15007.1.3.1.1.1.1.1 |
mefSoamPmMepLmSingleEndedResponderThis object specifies whether the Loss Measurement (LMM) single-ended
Responder is enabled.
The value 'true' indicates the single-ended Loss Measurement Responder
is enabled and if a LMM message is received a LMR will be sent in reply.
The value 'false' indicates the single-ended Loss Measurement Responder
is disabled. If a LMM message is received no response will be sent and
the message will be discarded.
This object needs to be persistent upon reboot or restart of a device.
A MEP can be both a single-ended Responder and Controller simultaneously.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.1.1.1.2 |
mefSoamPmMepSlmSingleEndedResponderThis object specifies whether the Synthetic Loss Measurement (SLM)
single-ended Responder is enabled.
The value 'true' indicates the single-ended SLM Responder is enabled and
if a SLM message is received a SLR will be sent in reply.
The value 'false' indicates the single-ended SLM Responder is disabled.
If a SLM message is received no response will be sent and the message
will be discarded.
This object needs to be persistent upon reboot or restart of a device.
A MEP can be both a single-ended Responder and Controller simultaneously.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.1.1.1.3 |
mefSoamPmMepDmSingleEndedResponderThis object specifies whether the Delay Measurement (DMM) single
ended Responder is enabled.
The value 'true' indicates the single-ended Delay Measurement Responder
is enabled and if a DMM message is received a DMR will be sent in reply.
The value 'false' indicates the single-ended Delay Measurement Responder
is disabled. If a DMM message is received no response will be sent and
the message will be discarded.
This object needs to be persistent upon reboot or restart of a device.
A MEP can be both a single-ended Responder and Controller simultaneously.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.1.1.1.4 |
mefSoamPmLmObjects OBJECT IDENTIFIER .1.3.6.1.4.1.15007.1.3.1.2 |
mefSoamLmCfgTableThis table includes configuration objects and operations for the
Frame Loss Measurement function defined in [Y.1731] and [MEF SOAM-PM].
Each row in the table represents a Loss Measurement session for
the defined MEP. This table uses four indices. The first three indices
are the indices of the Maintenance Domain, MaNet, and MEP tables. The
fourth index is the specific LM session on the selected MEP. A
Loss Measurement session is created on an existing MEP by first
accessing the mefSoamPmMepOperNextIndex object and using this value as
the mefSoamLmCfgIndex in the row creation.
Some writable objects in this table are only applicable in certain cases
(as described under each object), and attempts to write values for them
in other cases will be ignored.
The writable objects in this table need to be persistent upon reboot
or restart of a device. SEQUENCE OF MefSoamLmCfgEntry .1.3.6.1.4.1.15007.1.3.1.2.1 |
mefSoamLmCfgEntryThe conceptual row of mefSoamLmCfgTable. MefSoamLmCfgEntry .1.3.6.1.4.1.15007.1.3.1.2.1.1 |
mefSoamLmCfgIndexAn index to the Loss Measurement Configuration table which indicates
the specific measurement session for the MEP.
mefSoamPmMepOperNextIndex needs to be inspected to find an
available index for row-creation.
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never reused for other PM sessions on the same MEP while this
session is active. The index value keeps increasing until it
wraps to 0. This is to facilitate access control based
on a fixed index for an EMS, since the index is not reused. Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.1.1.1 |
mefSoamLmCfgTypeThis object specifies what type of Loss Measurement
will be performed.
lmLmm(1) LMM SOAM PDU generated and received LMR responses tracked
lmSlm(2) SLM SOAM PDU generated and received SLR responses tracked
lmCcm(3) CCM SOAM PDU generated and received CCM PDUs tracked
The lmSlm value is required. The lmLmm and lmCcm values are optional.
The lmCcm loss measurement values are only valid for a point-to-point
MEG. Multipoint MEGs may give unreliable loss measurements.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Enumeration .1.3.6.1.4.1.15007.1.3.1.2.1.1.2 |
mefSoamLmCfgVersionThis object indicates the version of the PDUs used to perform
Loss Measurement.
The value is placed in the Version field of the PDU and indicates
that the PDU format used is the format defined in Y.1731 with
that version.
The exact PDUs to use are specified by this object in combination with
mefSoamLmCfgType.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.1.1.3 |
mefSoamLmCfgEnabledThis object specifies whether the Loss Measurement session
is enabled.
The value 'true' indicates the Loss Measurement session is enabled and
SOAM PDUs are sent and/or measurements are collected when the session
is running according to the scheduling objects (start time, stop time,
etc.).
The value 'false' indicates the Loss Measurement session is disabled
and SOAM PDUs are not sent and/or measurements collected.
For a Loss Measurement session to be removed the row is
deleted in order to release internal resources.
This object can written/modified after row creation time.
If the LM session is enabled it resumes after shutdown/restart.
If the LM session is disabled the current Measurement Interval is
stopped, if it in process at the time, and all the in process calculations
for the partially completed Measurement Interval are finalized.
This object does not affect whether the single-ended Responder is
enabled or not, which is enabled or disabled by the
mefSoamPmMepLmSingleEndedResponder and
mefSoamPmMepSlmSingleEndedResponder objects.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.1.1.4 |
mefSoamLmCfgMeasurementEnableA vector of bits that indicates the type of SOAM LM counters found
in the mefSoamLmMeasuredStatsTable, mefSoamLmCurrentStatsTable,
mefSoamLmHistoryStatsTable, mefSoamLmCurrentAvailStatsTable and
mefSoamLmHistoryAvailStatsTable that are enabled.
A bit set to '1' enables the specific SOAM LM counter. A bit set to
'0' disables the SOAM LM counter.
If a particular SOAM LM counter is not supported the BIT value is
set to '0'.
Not all SOAM LM counters are supported for all SOAM LM types.
This object can only be written at row creation time and cannot be
modified once it has been created.
bForwardTransmitedFrames (0)
Enables/disables the mefSoamLmCurrentStatsForwardTransmittedFrames
and mefSoamLmHistoryStatsForwardTransmittedFrames counters.
bForwardReceivedFrames(1)
Enables/disables the mefSoamLmCurrentStatsForwardReceivedFrames
and mefSoamLmHistoryStatsForwardReceivedFrames counters.
bForwardMinFlr(2)
Enables/disables the mefSoamLmCurrentStatsForwardMinFlr
and mefSoamLmHistoryStatsForwardMinFlr counters.
bForwardMaxFlr(3)
Enables/disables the mefSoamLmCurrentStatsForwardMaxFlr
and mefSoamLmHistoryStatsForwardMaxFlr counters.
bForwardAvgFlr(4)
Enables/disables the mefSoamLmCurrentStatsForwardAvgFlr
and mefSoamLmHistoryStatsForwardAvgFlr counters.
bBackwardTransmitedFrames(5)
Enables/disables the mefSoamLmCurrentStatsBackwardTransmittedFrames
and mefSoamLmHistoryStatsBackwardTransmittedFrames counters.
bBackwardReceivedFrames(6)
Enables/disables the mefSoamLmCurrentStatsBackwardReceivedFrames
and mefSoamLmHistoryStatsBackwardReceivedFrames counters.
bBackwardMinFlr(7)
Enables/disables the mefSoamLmCurrentStatsBackwardMinFlr
and mefSoamLmHistoryStatsBackwardMinFlr counters.
bBackwardMaxFlr(8)
Enables/disables the mefSoamLmCurrentStatsBackwardMaxFlr
and mefSoamLmHistoryStatsBackwardMaxFlr counters.
bBackwardAvgFlr(9)
Enables/disables the mefSoamLmCurrentStatsBackwardAvgFlr
and mefSoamLmHistoryStatsBackwardAvgFlr counters.
bSoamPdusSent (10)
Enables/disables the mefSoamLmCurrentStatsSoamPdusSent
and mefSoamLmHistoryStatsSoamPdusSent counters.
bSoamPdusReceivedbReceivedMeasurements (11)
Enables/disables the mefSoamLmCurrentStatsSoamPdusReceived
and mefSoamLmHistoryStatsSoamPdusReceived counters.
bAvailForwardHighLoss(12)
Enables/disables the mefSoamLmCurrentAvailStatsForwardHighLoss
and mefSoamLmHistoryAvailStatsForwardHighLoss counters.
bAvailForwardConsecutiveHighLoss(13)
Enables/disables the mefSoamLmCurrentAvailStatsForwardConsecutiveHighLoss
and mefSoamLmHistoryAvailStatsForwardConsecutiveHighLoss counters.
bAvailForwardAvailable(14)
Enables/disables the mefSoamLmCurrentAvailStatsForwardAvailable
and mefSoamLmHistoryAvailStatsForwardAvailable counters.
bAvailForwardUnavailable(15)
Enables/disables the mefSoamLmCurrentAvailStatsForwardUnavailable
and mefSoamLmHistoryAvailStatsForwardUnavailable counters.
bAvailForwardMinFlr(16)
Enables/disables the mefSoamLmCurrentAvailStatsForwardMinFlr
and mefSoamLmHistoryAvailStatsForwardMinFlr counters.
bAvailForwardMaxFlr(17)
Enables/disables the mefSoamLmCurrentAvailStatsForwardMaxFlr
and mefSoamLmHistoryAvailStatsForwardMaxFlr counters.
bAvailForwardAvgFlr(18)
Enables/disables the mefSoamLmCurrentAvailStatsForwardAvgFlr
and mefSoamLmHistoryAvailStatsForwardAvgFlr counters.
bAvailBackwardHighLoss(19)
Enables/disables the mefSoamLmCurrentAvailStatsBackwardHighLoss
and mefSoamLmHistoryAvailStatsBackwardHighLoss counters.
bAvailBackwardConsecutiveHighLoss(20)
Enables/disables the mefSoamLmCurrentAvailStatsBackwardConsecutiveHighLoss
and mefSoamLmHistoryAvailStatsBackwardConsecutiveHighLoss counters.
bAvailBackwardAvailable(21)
Enables/disables the mefSoamLmCurrentAvailStatsBackwardAvailable
and mefSoamLmHistoryAvailStatsBackwardAvailable counters.
bAvailBackwardUnavailable(22)
Enables/disables the mefSoamLmCurrentAvailStatsBackwardUnavailable
and mefSoamLmHistoryAvailStatsBackwardUnavailable counters.
bAvailBackwardMinFlr(23)
Enables/disables the mefSoamLmCurrentAvailStatsBackwardMinFlr
and mefSoamLmHistoryAvailStatsBackwardMinFlr counters.
bAvailBackwardMaxFlr(24)
Enables/disables the mefSoamLmCurrentAvailStatsBackwardMaxFlr
and mefSoamLmHistoryAvailStatsBackwardMaxFlr counters.
bAvailBackwardAvgFlr(25)
Enables/disables the mefSoamLmCurrentAvailStatsBackwardAvgFlr
and mefSoamLmHistoryAvailStatsBackwardAvgFlr counters.
bMeasuredStatsForwardMeasuredFlr(26)
Enables/disables the mefSoamLmMeasuredStatsForwardFlr counter.
bMeasuredStatsBackwardMeasuredFlr(27)
Enables/disables the mefSoamLmMeasuredStatsBackwardFlr counter.
bMeasuredStatsAvailForwardStatus(28)
Enables/disables the mefSoamLmMeasuredStatsAvailForwardStatus counter.
bMeasuredStatsAvailBackwardStatus(29)
Enables/disables the mefSoamLmMeasuredStatsAvailBackwardStatus counter.rw Bits .1.3.6.1.4.1.15007.1.3.1.2.1.1.5 |
mefSoamLmCfgMessagePeriodThis object specifies the interval between Loss Measurement
OAM message transmission. For Loss Measurement monitoring
applications the default value is 1 sec.
This object is not applicable if mefSoamLmCfgType is set to lmCcm
and is ignored for that Loss Measurement Type.
This object can only be written at row creation time and cannot be
modified once it has been created.rw MefSoamTcMeasurementPeriodType UNITS "ms" .1.3.6.1.4.1.15007.1.3.1.2.1.1.6 |
mefSoamLmCfgPriorityThis object specifies the Loss Measurement OAM message priority
as well as the priority of the service/OAM traffic to be monitored.
Only frames of the same Class of Service are counted.
The default value is to be the value which yields the lowest frame
loss.
This object is not applicable if mefSoamLmCfgType is set to lmCcm.
This object can only be written at row creation time and cannot be
modified once it has been created.rw IEEE8021PriorityValue (IEEE8021-TC-MIB) .1.3.6.1.4.1.15007.1.3.1.2.1.1.7 |
mefSoamLmCfgFrameSizeThis object specifies the Loss Measurement frame size between
64 bytes and the maximum transmission unit of the EVC.
The range of frame sizes from 64 through 2000 octets need to be
supported, and the range of frame sizes from 2001 through 9600 octets
is suggested be supported.
The adjustment to the frame size of the standard frame size is
accomplished by the addition of a Data or Test TLV. A Data or Test TLV
is only added to the frame if the frame size is greater than 64 bytes.
This object is only valid for the entity transmitting the Loss
Measurement frames, type 'lmSlm', and is ignored by the
entity receiving frames. It is not applicable for the 'lmCcm' or
'lmLmm' types.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.1.1.8 |
mefSoamLmCfgDataPatternThis object specifies the LM data pattern included in a Data TLV
when the size of the LM frame is determined by the
mefSoamLmFrameSize object and mefSoamLmTestTlvIncluded is 'false'.
If the frame size object does not define the LM frame size or
mefSoamLmTestTlvIncluded is 'true' the value of this object is
ignored.
This object can only be written at row creation time and cannot be
modified once it has been created.rw MefSoamTcDataPatternType (MEF-SOAM-TC-MIB) .1.3.6.1.4.1.15007.1.3.1.2.1.1.9 |
mefSoamLmCfgTestTlvIncludedIndicates whether a Test TLV or Data TLV is included when the size
of the LM frame is determined by the mefSoamLmFrameSize object.
A value of 'true' indicates that the Test TLV is to be included. A
value of 'false' indicates that the Data TLV is to be included.
If the frame size object does not define the LM frame size
the value of this object is ignored.
This object can only be written at row creation time and cannot be
modified once it has been created.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.1.1.10 |
mefSoamLmCfgTestTlvPatternThis object specifies the type of test pattern to be
sent in the LM frame Test TLV when the size of LM PDU is
determined by the mefSoamLmFrameSize object and
mefSoamLmTestTlvIncluded is 'true'. If the frame size object
does not define the LM frame size or mefSoamLmTestTlvIncluded
is 'false' the value of this object is ignored.
This object can only be written at row creation time and cannot be
modified once it has been created.rw MefSoamTcTestPatternType (MEF-SOAM-TC-MIB) .1.3.6.1.4.1.15007.1.3.1.2.1.1.11 |
mefSoamLmCfgMeasurementIntervalThis object specifies the Measurement Interval for FLR statistics, in minutes.
A Measurement Interval of 15 minutes needs to be supported, other intervals
may be supported.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.1.1.12 |
mefSoamLmCfgNumIntervalsStoredThis object specifies the number of completed Measurement Intervals
to store in the history statistic table (mefSoamLmHistoryStatsTable)
and the history availability statistic table
(mefSoamLmHistoryAvailStatsTable).
At least 32 completed Measurement Intervals need to be stored. 96
Measurement Intervals are recommended to be stored.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.1.1.13 |
mefSoamLmCfgDestMacAddressThe Target or Destination MAC Address Field to be transmitted.
If mefSoamLmCfgType is 'lmCcm', the destination MAC address is always a
multicast address indicating the level of the MEG: 01-80-c2-00-00-3y,
where y is the level of the MEG. An error is returned if this object
is set to any other value.
If mefSoamLmCfgType is 'lmLmm' or 'lmSlm', the destination address is
the unicast address of the destination MEP. An error is returned if
this object is set to a multicast address.
This address will be used if the value of the object
mefSoamLmDestIsMepId is 'false'.
This object is only valid for the entity transmitting the
SOAM LM frames and is ignored by the entity receiving
SOAM LM frames.
This object can only be written at row creation time and cannot be
modified once it has been created.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.1.1.14 |
mefSoamLmCfgDestMepIdThe Maintenance Association End Point Identifier of
another MEP in the same Maintenance Association to which
the SOAM LM frame is to be sent.
This address will be used if the value of the column
mefSoamLmDestIsMepId is 'true'. A value of zero
means that the destination MEP ID has not been configured.
This object is only valid for the entity transmitting the Loss
Measurement frames, types 'lmLmm' and 'lmSlm'. It is not applicable for
the 'lmCcm' type.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Dot1agCfmMepIdOrZero .1.3.6.1.4.1.15007.1.3.1.2.1.1.15 |
mefSoamLmCfgDestIsMepIdA value of 'true' indicates that MEPID of the target MEP is used for
SOAM LM frame transmission.
A value of 'false' indicates that the MAC address of the
target MEP is used for SOAM LM frame transmission.
This object is only valid for the entity transmitting the Loss
Measurement frames, types 'lmLmm' and 'lmSlm'. It is not applicable for
the 'lmCcm' type.
This object can only be written at row creation time and cannot be
modified once it has been created.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.1.1.16 |
mefSoamLmCfgStartTimeTypeThis object specifies the type of start time of the SOAM LM
session. The start time can be disabled (none), immediate, relative,
or fixed.
The value of 'none' is illegal and a write error will be returned
if this value is used.
The value of 'immediate' starts the SOAM LM session when the
mefSoamLmCfgEnabled is true.
The value of 'fixed' starts the SOAM LM session when the
mefSoamLmFixedStartDateAndTime is less than or equal to the current
system date and time and mefSoamLmCfgEnabled is true. This value is used
to implement an On-Demand fixed time PM session.
The value of 'relative' starts the SOAM LM session when the current
system date and time minus the mefSoamLmRelativeStartTime is greater
than or equal to the system date and time when the mefSoamLmStartTimeType
object was written and mefSoamLmCfgEnabled is true. This value is used
to implement an On-Demand relative time PM session.
This object can only be written at row creation time and cannot be
modified once it has been created.rw MefSoamTcOperationTimeType (MEF-SOAM-TC-MIB) .1.3.6.1.4.1.15007.1.3.1.2.1.1.17 |
mefSoamLmCfgFixedStartDateAndTimeThis object specifies the fixed start date/time for the
SOAM Loss Measurement session. This object is used only used if
mefSoamLmStartTimeType is 'fixed' and is ignored otherwise.
The default value is year 0000, month 01, day 01, time 00:00:00.00.
This object can only be written at row creation time and cannot be
modified once it has been created.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.1.1.18 |
mefSoamLmCfgRelativeStartTimeThis object specifies the relative start time, from the
current system time, for the SOAM LM session. This
object is used only if mefSoamLmStartTimeType is 'relative' and is
ignored otherwise.
This object can only be written at row creation time and cannot be
modified once it has been created.rw TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.1.1.19 |
mefSoamLmCfgStopTimeTypeThis object specifies the type of stop time to terminate the
SOAM LM session. The stop time can be forever (none), relative, or
fixed.
The value of 'none' indicates that the SOAM LM session never ends once it
has started unless it the session is disabled.
The value of 'immediate' is illegal and a write error will be returned
if this value is used.
The value of 'fixed' stops the SOAM LM session when the
mefSoamLmFixedStopDateAndTime is less than or equal
to the current system date and time. This
value is used to implement an On-Demand fixed time PM session.
The value of 'relative' stops the SOAM LM session when the time
indicated by mefSoamLmRelativeStopTime has passed since the session
start time as determined by the mefSoamLmCfgStartTimeType,
mefSoamLmCfgFixedStartDateAndTime and mefSoamLmCfgRelativeStartTime
objects. This value is used to implement an On-Demand relative time
PM session.
This object can only be written at row creation time and cannot be
modified once it has been created.rw MefSoamTcOperationTimeType (MEF-SOAM-TC-MIB) .1.3.6.1.4.1.15007.1.3.1.2.1.1.20 |
mefSoamLmCfgFixedStopDateAndTimeThis object specifies the fixed stop date/time for the
SOAM Loss Measurement session. This object is used only used
if mefSoamLmStopTimeType is 'fixed' and is ignored otherwise.
The default value is year 0000, month 01, day 01, time 00:00:00.00.
This object can only be written at row creation time and cannot be
modified once it has been created.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.1.1.21 |
mefSoamLmCfgRelativeStopTimeThis object specifies the relative stop time, from the
session start time, to stop the SOAM LM session. This
object is used only if mefSoamLmStopTimeType is 'relative' and is
ignored otherwise.
This object can only be written at row creation time and cannot be
modified once it has been created.rw TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.1.1.22 |
mefSoamLmCfgRepetitionTimeThis object specifies a configurable repetition time between
Measurement Intervals in a Loss Measurement session, in seconds.
If the value is 0 (none), there is no time gap between the end of one
Measurement Interval and the start of a new Measurement Interval.
This is the normal usage case.
If the value is greater than 0 but less than or equal to the measurement
interval, an error is returned.
If the value is greater than one Measurement Interval there is time gap
between the end of one Measurement Interval and the start of the next
Measurement Interval. The repetition time specifies the time between
the start of consecutive Measurement Intervals; hence the gap between
the end of one Measurement Interval and the start of the next is equal
to the difference between the repetition time and the measurement
interval. During this gap, no SOAM PDUs are sent for this session and
no measurements are made.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.1.1.23 |
mefSoamLmCfgAlignMeasurementIntervalsThis object specifies whether the Measurement Intervals for
the Loss Measurement session are aligned with a zero offset to
real time.
The value 'true' indicates that each Measurement Interval starts
at a time which is aligned to NE time source hour, if the repetition
time (or the Measurement Interval, if the repetition time is 0) is
a factor of an hour, i.e. 60min/15min = 4. For instance, a
Measurement Interval/repetition time of 15 minutes would stop/start
the Measurement Interval at 0, 15, 30, and 45 minutes of an hour. A
Measurement Interval/Repetition Time of 7 minutes would not align
to the hour since 7 minutes is NOT a factor of an hour, i.e.
60min/7min = 8.6. In this case the behavior is the same as if the
object is set to 'false'.
The value 'false' indicates that the first Measurement Interval starts
at an arbitrary time and each subsequent Measurement Interval starts
at a time which is determined by mefSoamLmCfgRepetitionTime.
This object can only be written at row creation time and cannot be
modified once it has been created.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.1.1.24 |
mefSoamLmCfgAlignMeasurementOffsetThis object specifies the offset in minutes from the time of day value
if mefSoamLmCfgAlignMeasurementIntervals is 'true' and the repetition
time is a factor of 60 minutes. If not, the value of this object
is ignored.
If the Measurement Interval is 15 minutes and
mefSoamLmCfgAlignMeasurementIntervals is true and if this object was
set to 5 minutes, the Measurement Intervals would start at 5, 20, 35, 50
minutes past each hour.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.1.1.25 |
mefSoamLmCfgAvailabilityMeasurementIntervalThis object specifies the availability Measurement Interval in
minutes.
A Measurement Interval of 15 minutes is to be supported, other intervals
can be supported.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.1.1.26 |
mefSoamLmCfgAvailabilityNumConsecutiveMeasPdusThis object specifies a configurable number of consecutive
loss measurement PDUs to be used in evaluating the
availability/unavailability status of each availability
indicator per MEF 10.2.1. Loss Measurement PDUs (LMMs, CCMs or
SLMs) are sent regularly with a period defined by
mefSoamLmCfgMessagePeriod. Therefore, this object, when
multiplied by mefSoamLmCfgMessagePeriod, is equivalent to
the Availability parameter of 'delta_t' as specified by MEF 10.2.1.
If the mefSoamLmCfgType is lmLMM or lmCCM, this object defines the
number of LMM or CCM PDUs transmitted during each 'delta_t' period.
The Availability flr for a given 'delta_t' can be calculated based
on the counters in the last LMM/R or CCM during this 'delta_t' and
the last LMM/R or CCM in the previous 'delta_t'.
If the mefSoamLmCfgType is lmSLM, this object defines the number
of SLM PDUs transmitted during each 'delta_t' period. The
Availability flr for a given 'delta_t' is calculated based on the
number of those SLM PDUs that are lost.
If the mefSoamLmCfgType is lmLMM or lmCCM, the number range of 1
through 10 must be supported. The number range of 10 through 1000000
may be supported, but is not mandatory.
If the mefSoamLmCfgType is lmSLM, the number range of 10 through
100 must be supported. The number range of 100 through 1000000
may be supported, but is not mandatory.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.1.1.27 |
mefSoamLmCfgAvailabilityFlrThresholdThis object specifies a configurable availability threshold to be
used in evaluating the availability/unavailability status of an
availability indicator per MEF 10.2.1. The availability threshold range
of 0.00 (0) through 1.00 (100000) is supported. This parameter is
equivalent to the Availability parameter of 'C' as specified by
MEF 10.2.1.
Units are in milli-percent, where 1 indicates 0.001 percent.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.1.1.28 |
mefSoamLmCfgAvailabilityNumConsecutiveIntervalsThis object specifies a configurable number of consecutive
availability indicators to be used to determine a change in the
availability status as indicated by MEF 10.2.1. This parameter is
equivalent to the Availability parameter of 'n' as specified
by MEF 10.2.1.
The number range of 1 through 10 must be supported. The number range
of 1 through 1000 may be supported, but is not mandatory.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.1.1.29 |
mefSoamLmCfgAvailabilityNumConsecutiveHighFlrThis object specifies a configurable number of consecutive
availability indicators to be used for assessing CHLI. This
parameter is equivalent to the Resilency parameter of 'p' as
specified by MEF 10.2.1.
mefSoamLmCfgAvailabilityNumConsecutiveHighFlr must be strictly less than
mefSoamLmCfgAvailabilityNumConsecutiveIntervals. If not, the count of high
loss intervals over time, mefSoamLmAvailabilityHighLoss, and the count
of consecutive high loss levels, mefSoamLmAvailabilityConsecutiveHighLoss,
is disabled.
The number range of 1 through 10 must be supported. The number range
of 1 through 1000 may be supported, but is not mandatory.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.1.1.30 |
mefSoamLmCfgSessionTypeThis object indicates whether the current session is defined to
be 'Proactive' or 'On-Demand'. A value of 'proactive'
indicates the current session is 'Proactive'. A value of 'onDemand'
indicates the current session is 'On-Demand'.
This object can only be written at row creation time and cannot be
modified once it has been created.rw MefSoamTcSessionType (MEF-SOAM-TC-MIB) .1.3.6.1.4.1.15007.1.3.1.2.1.1.31 |
mefSoamLmCfgSessionStatusThis object indicates the current status of the LM session. A value
of 'active' indicates the current LM session is active, i.e. the current
time lies between the start time and the stop time, and
mefSoamLmCfgEnabled is true. A value of 'notActive' indicates the
current LM session is not active, i.e. it has not started yet, has
stopped upon reaching the stop time, or is disabled.ro MefSoamTcStatusType (MEF-SOAM-TC-MIB) .1.3.6.1.4.1.15007.1.3.1.2.1.1.32 |
mefSoamLmCfgHistoryClearThis object when written clears the Loss Measurement history
Table (mefSoamLmHistoryStatsTable) - all rows are deleted.
When read the value always returns 'false'.
Writing this value does not change the current stat table,
nor any of the items in the configuration table.
Writing this value during row creation has no effect.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.1.1.33 |
mefSoamLmCfgRowStatusThe status of the row.
The writable columns in a row cannot be changed if the row
is active, except for mefSoamLmCfgHistoryClear and mefSoamLmCfgEnabled
objects. All columns must have a valid value before a row
can be activated.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.1.1.34 |
mefSoamLmMeasuredStatsTableThis object contains the last measured results for a SOAM Loss
Measurement session.
Each row in the table represents a Loss Measurement session for
the defined MEP. This table uses four indices. The first three indices
are the indices of the Maintenance Domain, MaNet, and MEP tables. The
fourth index is the specific LM session on the selected MEP.
Instances of this managed object are created automatically
by the SNMP Agent when the Loss Measurement session is running.
Each object in this table applies only if the corresponding bit is set in
mefSoamLmCfgMeasurementEnable.
The objects in this table do not need to be persistent upon reboot
or restart of a device. SEQUENCE OF MefSoamLmMeasuredStatsEntry .1.3.6.1.4.1.15007.1.3.1.2.2 |
mefSoamLmMeasuredStatsEntryThe conceptual row of mefSoamLmMeasuredStatsTable MefSoamLmMeasuredStatsEntry .1.3.6.1.4.1.15007.1.3.1.2.2.1 |
mefSoamLmMeasuredStatsForwardFlrThis object contains the last frame loss ratio in the forward direction
calculated by this MEP. The FLR value
is a ratio that is expressed as a percent with a value of 0 (ratio
0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.2.1.1 |
mefSoamLmMeasuredStatsBackwardFlrThis object contains the last frame loss ratio in the backward direction
calculated by this MEP. The FLR value
is a ratio that is expressed as a percent with a value of 0 (ratio
0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.2.1.2 |
mefSoamLmMeasuredStatsAvailForwardStatusThis object indicates the availability status (the outcome of the
last known availability indicator) in the forward direction.
Note that the status of an availability indicator is not known until
the loss for a number of subsequent availability indicators has been
calculated (as determined by
mefSoamLmCfgAvailabilityNumConsecutiveIntervals)ro MefSoamTcAvailabilityType (MEF-SOAM-TC-MIB) .1.3.6.1.4.1.15007.1.3.1.2.2.1.3 |
mefSoamLmMeasuredStatsAvailBackwardStatusThis object indicates the availability status (the outcome of the
last availability indicator) in the backward direction.
Note that the status of an availability indicator is not known until
the loss for a number of subsequent availability indicators has been
calculated (as determined by
mefSoamLmCfgAvailabilityNumConsecutiveIntervals)ro MefSoamTcAvailabilityType (MEF-SOAM-TC-MIB) .1.3.6.1.4.1.15007.1.3.1.2.2.1.4 |
mefSoamLmMeasuredStatsAvailForwardLastTransitionTimeThis object indicates the time of the last transition
between available and unavailable in the forward direction.
If there have been no transitions since the Loss Measurement
Session was started, this is set to 0.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.2.1.5 |
mefSoamLmMeasuredStatsAvailBackwardLastTransitionTimeThis object indicates the time of the last transition
between available and unavailable in the backward direction.
If there have been no transitions since the Loss Measurement
Session was started, this is set to 0.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.2.1.6 |
mefSoamLmCurrentAvailStatsTableThis object contains the current results for a SOAM Loss Measurement
session for availability statistics gathered during the interval
indicated by mefSoamLmCfgAvailabilityMeasurementInterval.
Each row in the table represents a Loss Measurement session for
the defined MEP. This table uses four indices. The first three indices
are the indices of the Maintenance Domain, MaNet, and MEP tables. The
fourth index is the specific LM session on the selected MEP.
Instances of this managed object are created automatically
by the SNMP Agent when the Loss Measurement session is running.
The objects in this table apply regardless of the value of
mefSoamLmCfgType unless otherwise specified in the object description.
Except for mefSoamLmCurrentAvailStatsIndex,
mefSoamLmCurrentAvailStatsStartTime, mefSoamLmCurrentAvailStatsElapsedTime
and mefSoamLmCurrentAvailStatsSuspect, each object in this table applies
only if the corresponding bit is set in mefSoamLmCfgMeasurementEnable.
The objects in this table may be persistent upon reboot or restart
of a device. SEQUENCE OF MefSoamLmCurrentAvailStatsEntry .1.3.6.1.4.1.15007.1.3.1.2.3 |
mefSoamLmCurrentAvailStatsEntryThe conceptual row of mefSoamLmCurrentAvailStatsTable MefSoamLmCurrentAvailStatsEntry .1.3.6.1.4.1.15007.1.3.1.2.3.1 |
mefSoamLmCurrentAvailStatsIndexThe index for the current availability Measurement Interval for this
PM session. This value will become the value for
mefSoamLmHistoryAvailStatsIndex once the Measurement Interval
is completed. The duration of the Measurement Interval is specified
by mefSoamLmCfgAvailabilityMeasurementInterval.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.3.1.1 |
mefSoamLmCurrentAvailStatsStartTimeThe time that the current Measurement Interval started.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.3.1.2 |
mefSoamLmCurrentAvailStatsElapsedTimeThe time that the current Measurement Interval has been running, in 0.01
seconds.ro TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.3.1.3 |
mefSoamLmCurrentAvailStatsSuspectWhether the Measurement Interval has been marked as suspect.
The object is set to false at the start of a measurement
interval. It is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts servicero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.3.1.4 |
mefSoamLmCurrentAvailStatsForwardHighLossThis object is the number of high loss intervals (HLI) over
time in the forward direction.
The value starts at 0 and increments for every HLI that occurs.
This parameter is equivalent to 'L Sub T' found in MEF 10.2.1.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.3.1.5 |
mefSoamLmCurrentAvailStatsBackwardHighLossThis object is the number of high loss intervals (HLI) over
time in the backwards direction.
The value starts at 0 and increments for every HLI that occurs.
This parameter is equivalent to 'L Sub T' found in MEF 10.2.1.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.3.1.6 |
mefSoamLmCurrentAvailStatsForwardConsecutiveHighLossThis object is the number of consecutive high loss intervals
(CHLI) over time in the forward direction.
The value starts at 0 and increments for every HLI that occurs
that is determined to fall within a CHLI.
This parameter is equivalent to 'B Sub T' found in MEF 10.2.1.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.3.1.7 |
mefSoamLmCurrentAvailStatsBackwardConsecutiveHighLossThis object is the number of consecutive high loss intervals
(CHLI) over time in the backward direction.
The value starts at 0 and increments for every HLI that occurs
that is determined to fall within a CHLI.
This parameter is equivalent to 'B Sub T' found in MEF 10.2.1.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.3.1.8 |
mefSoamLmCurrentAvailStatsForwardAvailableThis object contains the number of availability indicators
evaluated as available in the forward direction by this MEP during
this Measurement Interval.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.2.3.1.9 |
mefSoamLmCurrentAvailStatsBackwardAvailableThis object contains the number of availability indicators
evaluated as available in the backward direction by this MEP during
this Measurement Interval.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.2.3.1.10 |
mefSoamLmCurrentAvailStatsForwardUnavailableThis object contains the number of availability indicators
evaluated as unavailable in the forward direction by this MEP during
this Measurement Interval.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.2.3.1.11 |
mefSoamLmCurrentAvailStatsBackwardUnavailableThis object contains the number of availability indicators
evaluated as unavailable in the backward direction by this MEP
during this Measurement Interval.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.2.3.1.12 |
mefSoamLmCurrentAvailStatsForwardMinFlrThis object contains the minimum one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.3.1.13 |
mefSoamLmCurrentAvailStatsForwardMaxFlrThis object contains the maximum one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.3.1.14 |
mefSoamLmCurrentAvailStatsForwardAvgFlrThis object contains the average one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.3.1.15 |
mefSoamLmCurrentAvailStatsBackwardMinFlrThis object contains the minimum one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.3.1.16 |
mefSoamLmCurrentAvailStatsBackwardMaxFlrThis object contains the maximum one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed
as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.3.1.17 |
mefSoamLmCurrentAvailStatsBackwardAvgFlrThis object contains the average one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.3.1.18 |
mefSoamLmCurrentStatsTableThis table contains the results for the current Measurement
Interval in a SOAM Loss Measurement session gathered during the interval
indicated by mefSoamLmCfgMeasurementInterval.
A row in this table is created automatically
by the SNMP Agent when the Loss Measurement session is configured.
Each row in the table represents the current statistics for a Loss
Measurement session for the defined MEP. This table uses four indices.
The first three indices are the indices of the Maintenance Domain, MaNet,
and MEP tables. The fourth index is the specific LM session on the
selected MEP. There may be more than one LM session per MEP. The
main use case for this is to allow multiple CoS instances to be
operating simultaneously for a MEP.
The objects in this table apply regardless of the value of
mefSoamLmCfgType unless otherwise specified in the object description.
Except for mefSoamLmCurrentStatsIndex, mefSoamLmCurrentStatsStartTime,
mefSoamLmCurrentStatsElapsedTime and mefSoamLmCurrentStatsSuspect,
each object in this table applies only if the corresponding bit is set in
mefSoamLmCfgMeasurementEnable.
The objects in this table do not need to be persistent upon reboot or
restart of a device. SEQUENCE OF MefSoamLmCurrentStatsEntry .1.3.6.1.4.1.15007.1.3.1.2.4 |
mefSoamLmCurrentStatsEntryThe conceptual row of mefSoamLmCurrentStatsTable MefSoamLmCurrentStatsEntry .1.3.6.1.4.1.15007.1.3.1.2.4.1 |
mefSoamLmCurrentStatsIndexThe index for the current Measurement Interval for this
PM session. This value will become the value for
mefSoamLmHistoryStatsIndex once the Measurement Interval
is completed.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.4.1.1 |
mefSoamLmCurrentStatsStartTimeThe time that the current Measurement Interval started.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.4.1.2 |
mefSoamLmCurrentStatsElapsedTimeThe time that the current Measurement Interval has been running, in 0.01
seconds.ro TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.4.1.3 |
mefSoamLmCurrentStatsSuspectWhether the Measurement Interval has been marked as suspect.
The object is set to false at the start of a measurement
interval. It is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts servicero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.4.1.4 |
mefSoamLmCurrentStatsForwardTransmittedFramesThis object contains the number of frames transmitted in the
forward direction by this MEP.
For a PM Session of types lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of type lmSlm this includes the count of SOAM
ETH-SLM frames only.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.2.4.1.5 |
mefSoamLmCurrentStatsForwardReceivedFramesThis object contains the number of frames received in the
forward direction by this MEP.
For a PM Session of types lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of types lmSlm this includes the count of SOAM
ETH-SLM frames only.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.2.4.1.6 |
mefSoamLmCurrentStatsForwardMinFlrThis object contains the minimum one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.4.1.7 |
mefSoamLmCurrentStatsForwardMaxFlrThis object contains the maximum one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.4.1.8 |
mefSoamLmCurrentStatsForwardAvgFlrThis object contains the average one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.4.1.9 |
mefSoamLmCurrentStatsBackwardTransmittedFramesThis object contains the number of frames transmitted in the
backward direction by this MEP.
For a PM Session of type lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of type lmSlm this includes the count of SOAM
ETH-SLM frames only.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.2.4.1.10 |
mefSoamLmCurrentStatsBackwardReceivedFramesThis object contains the number of frames received in the
backward direction by this MEP.
For a PM Session of type lmLmm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of type lmSlm this includes the count of SOAM
ETH-SLM frames only.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.2.4.1.11 |
mefSoamLmCurrentStatsBackwardMinFlrThis object contains the minimum one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.4.1.12 |
mefSoamLmCurrentStatsBackwardMaxFlrThis object contains the maximum one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed
as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.4.1.13 |
mefSoamLmCurrentStatsBackwardAvgFlrThis object contains the average one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.4.1.14 |
mefSoamLmCurrentStatsSoamPdusSentThis object contains the count of the number of SOAM PDUs sent
during this Measurement Interval.
This object applies when mefSoamLmCfgType is lmLmm, lmSlm, or
lmCcm. It indicates the number of LMM, CCM, or SLM SOAM frames
transmitted.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.2.4.1.15 |
mefSoamLmCurrentStatsSoamPdusReceivedThis object contains the count of the number of SOAM PDUs
PDUs received in this Measurement Interval.
This object applies when mefSoamLmCfgType is lmLmm, lmSlm, or
lmCcm. This object indicates the number of LMR, CCM, or SLR SOAM
frames received.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.2.4.1.16 |
mefSoamLmHistoryAvailStatsTableThis table contains the results for availability history Measurement
Intervals in a SOAM Loss Measurement session.
Rows of this table object are created automatically
by the SNMP Agent when the Loss Measurement session is running and a
Measurement Interval is completed.
Each row in the table represents the history statistics for a Loss
Measurement session availability Measurement Interval for the defined
MEP. This table uses five indices. The first three indices are the indices of
the Maintenance Domain, MaNet, and MEP tables. The fourth index is the
specific LM session on the selected MEP. The fifth index index the
specific Measurement Interval.
At least 32 completed Measurement Intervals are to be supported. 96
completed Measurement Intervals are recommended to be supported. If
there are at least 32 rows in the table and a new Measurement Interval
completes and a new row is to be added to the table, the oldest completed
Measurement Interval can be deleted (row deletion). If the availability
Measurement Interval is other than 15 minutes then a minimum of 8 hours of
completed Measurement Intervals are to be supported and 24 hours are
recommended to be supported.
Except for mefSoamLmHistoryAvailStatsIndex,
mefSoamLmHistoryAvailStatsEndTime, mefSoamLmHistoryAvailStatsElapsedTime and
mefSoamLmHistoryAvailStatsSuspect, each object in this table applies only
if the corresponding bit is set in mefSoamLmCfgMeasurementEnable.
The rows and objects in this table are to be persistent upon reboot
or restart of a device. SEQUENCE OF MefSoamLmHistoryAvailStatsEntry .1.3.6.1.4.1.15007.1.3.1.2.5 |
mefSoamLmHistoryAvailStatsEntryThe conceptual row of mefSoamLmHistoryAvailStatsTable MefSoamLmHistoryAvailStatsEntry .1.3.6.1.4.1.15007.1.3.1.2.5.1 |
mefSoamLmHistoryAvailStatsIndexThe index for the availability Measurement Interval within this
PM session.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1. Measurement Intervals
for availability (stored in this table) are based on
mefSoamLmCfgAvailabilityMeasurementInterval and are indexed independently
of Measurement Intervals for FLR (stored in mefSoamLmHistoryStatsTable).
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never reused while this session is active until it wraps to zero.
The index value keeps increasing up to that time. Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.5.1.1 |
mefSoamLmHistoryAvailStatsEndTimeThe time that the Measurement Interval ended.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.5.1.2 |
mefSoamLmHistoryAvailStatsElapsedTimeThe length of time that the Measurement Interval ran for,
in 0.01 seconds.ro TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.5.1.3 |
mefSoamLmHistoryAvailStatsSuspectWhether the Measurement Interval has been marked as suspect.
The object is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts servicero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.5.1.4 |
mefSoamLmHistoryAvailStatsForwardHighLossThis object is the number of high loss intervals (HLI) over
time in the forward direction.
The value starts at 0 and increments for every HLI that occurs.
This parameter is equivalent to 'L Sub T' found in MEF 10.2.1.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.5.1.5 |
mefSoamLmHistoryAvailStatsBackwardHighLossThis object is the number of high loss intervals (HLI) over
time in the backward direction.
The value starts at 0 and increments for every HLI that occurs.
This parameter is equivalent to 'L Sub T' found in MEF 10.2.1.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.5.1.6 |
mefSoamLmHistoryAvailStatsForwardConsecutiveHighLossThis object is the number of consecutive high loss intervals
(CHLI) over time in the forward direction.
The value starts at 0 and increments for every HLI that occurs
that is determined to fall within a CHLI.
This parameter is equivalent to 'B Sub T' found in MEF 10.2.1.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.5.1.7 |
mefSoamLmHistoryAvailStatsBackwardConsecutiveHighLossThis object is the number of consecutive high loss intervals
(CHLI) over time in the forward direction.
The value starts at 0 and increments for every HLI that occurs
that is determined to fall within a CHLI.
This parameter is equivalent to 'B Sub T' found in MEF 10.2.1.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.5.1.8 |
mefSoamLmHistoryAvailStatsForwardAvailableThis object contains the number of availability indicators
evaluated as available in the forward direction by this MEP during
this Measurement Interval.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.2.5.1.9 |
mefSoamLmHistoryAvailStatsBackwardAvailableThis object contains the number of availability indicators
evaluated as available in the backward direction by this MEP during
this Measurement Interval.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.2.5.1.10 |
mefSoamLmHistoryAvailStatsForwardUnavailableThis object contains the number of availability indicators
evaluated as unavailable in the forward direction by this MEP during
this Measurement Interval.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.2.5.1.11 |
mefSoamLmHistoryAvailStatsBackwardUnavailableThis object contains the number of availability indicators
evaluated as unavailable in the backward direction by this MEP
during this Measurement Interval.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.2.5.1.12 |
mefSoamLmHistoryAvailStatsForwardMinFlrThis object contains the minimum one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.5.1.13 |
mefSoamLmHistoryAvailStatsForwardMaxFlrThis object contains the maximum one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.5.1.14 |
mefSoamLmHistoryAvailStatsForwardAvgFlrThis object contains the average one-way availability flr in the forward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.5.1.15 |
mefSoamLmHistoryAvailStatsBackwardMinFlrThis object contains the minimum one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.5.1.16 |
mefSoamLmHistoryAvailStatsBackwardMaxFlrThis object contains the maximum one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed
as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.5.1.17 |
mefSoamLmHistoryAvailStatsBackwardAvgFlrThis object contains the average one-way availability flr in the backward
direction, from among the set of availability flr values calculated by
the MEP in this Measurement Interval. There is one availability flr
value for each 'delta_t' time period within the Measurement Interval, as
specified in MEF 10.2.1.
The flr value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.5.1.18 |
mefSoamLmHistoryStatsTableThis table contains the results for history Measurement
Intervals in a SOAM Loss Measurement session.
Rows of this table object are created automatically
by the SNMP Agent when the Loss Measurement session is running and a
Measurement Interval is completed.
Each row in the table represents the history statistics for a Loss
Measurement session Measurement Interval for the defined MEP. This
table uses five indices. The first three indices are the indices of
the Maintenance Domain, MaNet, and MEP tables. The fourth index is the
specific LM session on the selected MEP. The fifth index index the
specific Measurement Interval.
At least 32 completed Measurement Intervals are to be supported. 96
completed Measurement Intervals are recommended to be supported. If
there are at least 32 rows in the table and a new Measurement Interval
completes and a new row is to be added to the table, the oldest completed
Measurement Interval may be deleted (row deletion). If the measurement
interval is other than 15 minutes then a minimum of 8 hours of
completed Measurement Intervals are to be supported and 24 hours are
recommended to be supported.
Except for mefSoamLmHistoryStatsIndex, mefSoamLmHistoryStatsEndTime,
mefSoamLmHistoryStatsElapsedTime and mefSoamLmHistoryStatsSuspect,
each object in this table applies only if the corresponding bit is set in
mefSoamLmCfgMeasurementEnable.
The rows and objects in this table are to be persistent upon reboot
or restart of a device. SEQUENCE OF MefSoamLmHistoryStatsEntry .1.3.6.1.4.1.15007.1.3.1.2.6 |
mefSoamLmHistoryStatsEntryThe conceptual row of mefSoamLmHistoryStatsTable MefSoamLmHistoryStatsEntry .1.3.6.1.4.1.15007.1.3.1.2.6.1 |
mefSoamLmHistoryStatsIndexThe index for the Measurement Interval within this
PM session.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1. Measurement Intervals
for FLR (stored in this table) are based on
mefSoamLmCfgMeasurementInterval and are indexed independently
of Measurement Intervals for availability (stored in
mefSoamLmHistoryAvailStatsTable).
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never reused while this session is active until it wraps to zero.
The index value keeps increasing up to that time. Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.6.1.1 |
mefSoamLmHistoryStatsEndTimeThe time that the Measurement Interval ended.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.6.1.2 |
mefSoamLmHistoryStatsElapsedTimeThe length of time that the Measurement Interval ran for,
in 0.01 seconds.ro TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.6.1.3 |
mefSoamLmHistoryStatsSuspectWhether the Measurement Interval has been marked as suspect.
The object is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts servicero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.6.1.4 |
mefSoamLmHistoryStatsForwardTransmittedFramesThis object contains the number of frames transmitted in the
forward direction by this MEP.
For a PM Session of types lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of type lmSlm this includes the count of OAM
ETH-SLM frames only.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.2.6.1.5 |
mefSoamLmHistoryStatsForwardReceivedFramesThis object contains the number of frames received in the
forward direction by this MEP.
For a PM Session of types lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of type lmSlm this includes the count of OAM
ETH-SLM frames only.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.2.6.1.6 |
mefSoamLmHistoryStatsForwardMinFlrThis object contains the minimum one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.6.1.7 |
mefSoamLmHistoryStatsForwardMaxFlrThis object contains the maximum one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.6.1.8 |
mefSoamLmHistoryStatsForwardAvgFlrThis object contains the average one-way frame loss
ratio in the forward direction calculated by this MEP for this
Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.6.1.9 |
mefSoamLmHistoryStatsBackwardTransmittedFramesThis object contains the number of frames transmitted in the
backward direction by this MEP.
For a PM Session of type lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of types lmSlm this includes the count of SOAM
ETH-SLM frames only.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.2.6.1.10 |
mefSoamLmHistoryStatsBackwardReceivedFramesThis object contains the number of frames received in the
backward direction by this MEP.
For a PM Session of type lmLmm and lmCcm this includes Ethernet
Service Frames and SOAM PDUs that are in a higher MEG level only.
For a PM Session of types lmSlm this includes the count of SOAM
ETH-SLM frames only.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.2.6.1.11 |
mefSoamLmHistoryStatsBackwardMinFlrThis object contains the minimum one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.6.1.12 |
mefSoamLmHistoryStatsBackwardMaxFlrThis object contains the maximum one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.6.1.13 |
mefSoamLmHistoryStatsBackwardAvgFlrThis object contains the average one-way frame loss
ratio in the backward direction calculated by this MEP for
this Measurement Interval. The FLR value is a ratio that is expressed as a
percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00).
Units are in milli-percent, where 1 indicates 0.001 percent.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.6.1.14 |
mefSoamLmHistoryStatsSoamPdusSentThis object contains the count of the number of SOAM PDUs sent
during this Measurement Interval.
This object applies when mefSoamLmCfgType is lmLmm, lmSlm,
or lmCcm. It indicates the number of LMM, CCM, or SLM SOAM frames
transmitted.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.2.6.1.15 |
mefSoamLmHistoryStatsSoamPdusReceivedThis object contains the count of the number of SOAM
PDUs received in this Measurement Interval.
This object applies when mefSoamLmCfgType is lmLmm, lmSlm,
or lmCcm. This object indicates the number of LMR, CCM, or SLR
SOAM frames received.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.2.6.1.16 |
mefSoamLmThresholdCfgTableThis table contains the list of Loss Measurement configuration threshold
values for LM Performance Monitoring.
The main purpose of the threshold configuration table is to configure
threshold alarm notifications indicating that a specific performance
metric is not being met.
Each row in the table represents a Loss Measurement session threshold
set for the defined MEP. This table uses five indices. The first three
indices are the indices of the Maintenance Domain, MaNet, and MEP tables.
The fourth index is the specific LM session on the selected MEP. The
fifth index is the specific threshold set number.
Rows in this table are not created automatically. A row is created in
this table to set up a threshold set on a configured MEP that has a
configured LM session.
If two managers try to 'create' the same row at the same time, the first
creation would succeed, the second creation attempt would result in an
error. The second creation attempt would then need to select a new index
value to successfully create a new row.
An NE needs to support at least one threshold set for NE SOAM PM compliance. A
second threshold set on the NE is desirable. More than two threshold
sets can be configured on the NE if supported on the NE.
All the objects in the row have a default value that disables the
particular threshold measurement. In order to enable a threshold
measurement the particular bit in the mefSoamLmThresholdCfgEnable object
is to be set to '1' and the selected threshold measurement is to have
a threshold value configured. Non-configured threshold measurements
are disabled by default.
The writable objects in this table need to be persistent upon reboot
or restart of a device. SEQUENCE OF MefSoamLmThresholdCfgEntry .1.3.6.1.4.1.15007.1.3.1.2.7 |
mefSoamLmThresholdCfgEntryThe conceptual row of mefSoamLmThresholdCfgTable. MefSoamLmThresholdCfgEntry .1.3.6.1.4.1.15007.1.3.1.2.7.1 |
mefSoamLmThresholdCfgIndexThe index of the threshold number for the specific LM
threshold entry.
An index value of '1' needs to be supported. Other index values
can also be supported. Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.7.1.1 |
mefSoamLmThresholdCfgEnableA vector of bits that indicates the type of SOAM LM thresholds
notifications that are enabled.
A bit set to '1' enables the specific SOAM LM threshold notification
and when the specific counter is enabled and the threshold is crossed a
notification is generated.
A bit set to '0' disables the specific SOAM LM threshold notification.
If a particular SOAM LM threshold is not supported the BIT value is
set to '0'.
bMefSoamLmMeasuredFlrForwardThreshold(0)
Enables/disables measured frame loss forward ratio threshold
notification. The notification is sent immediately when the
mefSoamLmMeasuredStatsForwardFlr value is
greater than or equal to the threshold value.
bMefSoamLmMaxFlrForwardThreshold(1)
Enables/disables maximum frame loss forward ratio threshold
notification. The notification is sent immediately when the
mefSoamLmCurrentStatsForwardMaxFlr value is greater
than or equal to threshold value in a Measurement Interval.
bMefSoamLmAvgFlrForwardThreshold(2)
Enables/disables average frame loss forward ratio threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
mefSoamLmCurrentStatsForwardAvgFlr value is greater
than or equal to the threshold value.
bMefSoamLmMeasuredFlrBackwardThreshold(3)
Enables/disables measured frame loss backward ratio threshold
notification. The notification is sent immediately when the
mefSoamLmMeasuredStatsBackwardFlr value is
greater than or equal to the threshold value.
bMefSoamLmMaxFlrBackwardThreshold(4)
Enables/disables maximum frame loss backward ratio threshold
notification. The notification is sent immediately when the
mefSoamLmCurrentStatsBackwardMaxFlr value is greater
than or equal to threshold value in a Measurement Interval.
bMefSoamLmAvgFlrBackwardThreshold(5)
Enables/disables average frame loss backward ratio threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
mefSoamLmCurrentStatsBackwardAvgFlr value is
greater than or equal to the threshold value.
bMefSoamLmForwardHighLossThreshold(6)
Enables/disables forward high loss threshold
notification. The notification is sent immediately when the
mefSoamLmCurrentAvailStatsForwardHighLoss value is
greater than or equal to the threshold value in a measurement
interval.
bMefSoamLmForwardConsecutiveHighLossThreshold(7)
Enables/disables forward consecutive high loss threshold
notification. The notification is sent immediately when the
mefSoamLmCurrentAvailStatsForwardConsecutiveHighLoss value is
greater than or equal to the threshold value in a measurement
interval.
bMefSoamLmBackwardHighLossThreshold(8)
Enables/disables backward high loss threshold
notification. The notification is sent immediately when the
mefSoamLmCurrentAvailStatsBackwardHighLoss value is
greater than or equal to the threshold value in a measurement
interval.
bMefSoamLmBackwardConsecutiveHighLossThreshold(9)
Enables/disables backward consecutive high loss threshold
notification. The notification is sent immediately when the
mefSoamLmCurrentAvailStatsBackwardConsecutiveHighLoss value is
greater than or equal to the threshold value in a measurement
interval.
bMefSoamLmUnavailForwardThreshold(10)
Enables/disables unavailable forward threshold
notification. The notification is sent immediately when the
mefSoamLmCurrentAvailStatsForwardUnavailable value is
greater than or equal to threshold value in a Measurement Interval.
bMefSoamLmAvailRatioForwardThreshold(11)
Enables/disables availability ratio forward threshold
notification. The notification is sent immediately when the
availability ratio is greater than or equal to threshold value
in a Measurement Interval. The availability ratio can be calculated
from the values of mefSoamLmCurrentAvailStatsForwardAvailable and
mefSoamLmCurrentAvailStatsForwardUnavailable.
bMefSoamLmUnavailBackwardThreshold(12)
Enables/disables unavailable backward threshold
notification. The notification is sent immediately when the
mefSoamLmCurrentAvailStatsBackwardUnavailable value is
greater than or equal to threshold value in a Measurement Interval.
bMefSoamLmAvailRatioBackwardThreshold(13)
Enables/disables availability ratio backward threshold
notification. The notification is sent immediately when the
availability ratio is greater than or equal to threshold value
in a Measurement Interval. The availability ratio can be calculated
from the values of mefSoamLmCurrentAvailStatsBackwardAvailable and
mefSoamLmCurrentAvailStatsBackwardUnavailable.rw Bits .1.3.6.1.4.1.15007.1.3.1.2.7.1.2 |
mefSoamLmThresholdCfgMeasuredFlrForwardThresholdThis object is used to set the measured forward frame loss ratio
threshold value that will be used to determine if a threshold
notification is generated.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.7.1.3 |
mefSoamLmThresholdCfgMaxFlrForwardThresholdThis object is used to set the maximum forward frame loss ratio
threshold value that will be used to determine if a threshold
notification is generated.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.7.1.4 |
mefSoamLmThresholdCfgAvgFlrForwardThresholdThis object is used to set the average forward frame loss ratio
threshold value that will be used to determine if a threshold
notification is generated.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.7.1.5 |
mefSoamLmThresholdCfgMeasuredFlrBackwardThresholdThis object is used to set the measured backward frame loss ratio
threshold value that will be used to determine if a threshold
notification is generated.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.7.1.6 |
mefSoamLmThresholdCfgMaxFlrBackwardThresholdThis object is used to set the maximum backward frame loss ratio
threshold value that will be used to determine if a threshold
notification is generated.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.7.1.7 |
mefSoamLmThresholdCfgAvgFlrBackwardThresholdThis object is used to set the average backward frame loss ratio
threshold value that will be used to determine if a threshold
notification is generated.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.7.1.8 |
mefSoamLmThresholdCfgForwardHighLossThresholdThis object is used to set the forward high loss threshold value that
will be used to determine if a threshold notification is generated.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.7.1.9 |
mefSoamLmThresholdCfgForwardConsecutiveHighLossThresholdThis object is used to set the consecutive forward high loss
threshold value that will be used to determine if a threshold
notification is generated.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.7.1.10 |
mefSoamLmThresholdCfgBackwardHighLossThresholdThis object is used to set the backward high loss threshold value that
will be used to determine if a threshold notification is generated.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.7.1.11 |
mefSoamLmThresholdCfgBackwardConsecutiveHighLossThresholdThis object is used to set the consecutive backward high loss
threshold value that will be used to determine if a threshold
notification is generated.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.7.1.12 |
mefSoamLmThresholdCfgForwardUnavailCountThresholdThis object is used to set the forward unavailability
threshold value that will be used to determine if a threshold
notification is generated.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.7.1.13 |
mefSoamLmThresholdCfgForwardAvailRatioThresholdThis object is used to set the forward availability/total time
ratio threshold value that will be used to determine if a threshold
notification is generated if the ratio drops below the configured
value.
The ratio value is expressed as a percent with a value of 0 (ratio
0.00) through 100000 (ratio 1.00)
Units are in milli-percent, where 1 indicates 0.001 percent.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.7.1.14 |
mefSoamLmThresholdCfgBackwardUnavailCountThresholdThis object is used to set the backward unavailability
threshold value that will be used to determine if a threshold
notification is generated.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.7.1.15 |
mefSoamLmThresholdCfgBackwardAvailRatioThresholdThis object is used to set the backward availability/total time
ratio threshold value that will be used to determine if a threshold
notification is generated if the ratio drops below the configured
value.
The ratio value is expressed as a percent with a value of 0 (ratio
0.00) through 100000 (ratio 1.00)
Units are in milli-percent, where 1 indicates 0.001 percent.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.2.7.1.16 |
mefSoamLmThresholdCfgRowStatusThe status of the row.
The writable columns in a row cannot be changed if the row
is active. All columns are to have a valid value before a row
can be activated.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.2.7.1.17 |
mefSoamPmDmObjects OBJECT IDENTIFIER .1.3.6.1.4.1.15007.1.3.1.3 |
mefSoamDmCfgTableThis table includes configuration objects and operations for the
Delay Measurement function.
Each row in the table represents a Delay Measurement session for
the defined MEP. This table uses four indices. The first three indices
are the indices of the Maintenance Domain, MaNet, and MEP tables. The
fourth index is the specific DM session on the selected MEP.
A Delay Measurement session is created on an existing MEP by first
accessing the mefSoamDmOperNextIndex object and using this value as
the mefSoamDmCfgIndex in the row creation.
Some writable objects in this table are only applicable in certain cases
(as described under each object), and attempts to write values for them
in other cases will be ignored.
The writable objects in this table need to be persistent upon reboot
or restart of a device. SEQUENCE OF MefSoamDmCfgEntry .1.3.6.1.4.1.15007.1.3.1.3.1 |
mefSoamDmCfgEntryThe conceptual row of mefSoamDmCfgTable. MefSoamDmCfgEntry .1.3.6.1.4.1.15007.1.3.1.3.1.1 |
mefSoamDmCfgIndexAn index to the Delay Measurement Configuration table which indicates
the specific measurement session for the MEP.
mefSoamPmMepOperNextIndex needs to be inspected to find an
available index for row-creation.
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never reused for other PM sessions on the same MEP while this
session is active. The index value keeps increasing until it
wraps to zero. This is to facilitate access control based
on a fixed index for an EMS, since the index is not reused. Unsigned32 .1.3.6.1.4.1.15007.1.3.1.3.1.1.1 |
mefSoamDmCfgTypeThis object indicates what type of Delay Measurement is to
be performed.
dmDmm(1) DMM SOAM PDU generated, DMR responses received
(one-way or two-way measurements)
dm1DmTx(2) 1DM SOAM PDU generated (one-way measurements are made by
the receiver)
dm1DmRx(3) 1DM SOAM PDU received and tracked (one-way measurements)
The exact PDUs to use are specified by this object in combination with
mefSoamDmCfgVersion.
The value dmDMM is required. The values dm1DmTx and dm1DmRx are optional.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Enumeration .1.3.6.1.4.1.15007.1.3.1.3.1.1.2 |
mefSoamDmCfgVersionThis object indicates the version of the PDUs used to perform
Delay Measurement.
Version 0 indicates the PDU formats defined in Y.1731-2008.
Version 1 indicates the PDU formats defined in Y.1731-2011.
The exact PDUs to use are specified by this object in combination with
mefSoamDmCfgType.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.3.1.1.3 |
mefSoamDmCfgEnabledThis object specifies whether the Delay Measurement session is
enabled.
The value 'true' indicates the Delay Measurement session is enabled AND
SOAM PDUs are sent and/or measurements are collected when the session
is running according to the scheduling objects (start time, stop time,
etc.).
The value 'false' indicates the Delay Measurement session is disabled
AND SOAM PDUs are not sent and/or measurements collected.
For a Delay Measurement session to be removed the row is deleted in
order to release internal resources.
This object can written/modified after row creation time.
If the DM session is enabled it resumes after shutdown/restart.
If the DM session is disabled the current Measurement Interval is
stopped, if it in process at the time, and all the in process calculations
for the partially completed Measurement Interval are finalized.
This object does not affect whether the single-ended Responder is
enabled or not, which is enabled or disabled by the
mefSoamPmMepDmSingleEndedResponder object.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.3.1.1.4 |
mefSoamDmCfgMeasurementEnableA vector of bits that indicates the type of SOAM DM counters that
are enabled.
A bit set to '1' enables the specific SOAM DM counter.
A bit set to '0' disables the SOAM DM counter.
If a particular SOAM DM counter is not supported the BIT value is
set to '0'.
Not all SOAM DM counters are supported for all SOAM DM types.
This object can only be written at row creation time and cannot be
modified once it has been created.
bSoamPdusSent(0)
Enables/disables the mefSoamDmCurrentStatsSoamPdusSent
and mefSoamDmHistoryStatsSoamPdusSent counters.
bSoamPdusReceived(1)
Enables/disables the mefSoamDmCurrentStatsSoamPdusReceived
and mefSoamDmHistoryStatsSoamPdusReceived counters.
bFrameDelayTwoWayBins(2)
Enables/disables the mefSoamDmCurrentStatsBinsEntry counter
and the mefSoamDmHistoryStatsBinsEntry counter
when the mefSoamDmCfgMeasBinType is 'twoWayFrameDelay'.
bFrameDelayTwoWayMin(3)
Enables/disables the mefSoamDmCurrentStatsFrameDelayTwoWayMin
and mefSoamDmHistoryStatsFrameDelayTwoWayMin counters.
bFrameDelayTwoWayMax(4)
Enables/disables the mefSoamDmCurrentStatsFrameDelayTwoWayMax
and mefSoamDmHistoryStatsFrameDelayTwoWayMax counters.
bFrameDelayTwoWayAvg(5)
Enables/disables the mefSoamDmCurrentStatsFrameDelayTwoWayAvg
and mefSoamDmHistoryStatsFrameDelayTwoWayAvg counters.
bFrameDelayForwardBins(6)
Enables/disables the mefSoamDmCurrentStatsBinsEntry counter
and the mefSoamDmHistoryStatsBinsEntry counter
when the mefSoamDmCfgMeasBinType is 'forwardFrameDelay'.
bFrameDelayForwardMin(7)
Enables/disables the mefSoamDmCurrentStatsFrameDelayForwardMin
and mefSoamDmHistoryStatsFrameDelayForwardMin counters.
bFrameDelayForwardMax(8)
Enables/disables the mefSoamDmCurrentStatsFrameDelayForwardMax
and mefSoamDmHistoryStatsFrameDelayForwardMax counters.
bFrameDelayForwardAvg(9)
Enables/disables the mefSoamDmCurrentStatsFrameDelayForwardAvg
and mefSoamDmHistoryStatsFrameDelayForwardAvg counters.
bFrameDelayBackwardBins(10)
Enables/disables the mefSoamDmCurrentStatsBinsEntry counter
and the mefSoamDmHistoryStatsBinsEntry counter
when the mefSoamDmCfgMeasBinType is 'backwardFrameDelay'.
bFrameDelayBackwardMin(11)
Enables/disables the mefSoamDmCurrentStatsFrameDelayBackwardMin
and mefSoamDmHistoryStatsFrameDelayBackwardMin counters.
bFrameDelayBackwardMax(12)
Enables/disables the mefSoamDmCurrentStatsFrameDelayBackwardMax
and mefSoamDmHistoryStatsFrameDelayBackwardMax counters.
bFrameDelayBackwardAvg(13)
Enables/disables the mefSoamDmCurrentStatsFrameDelayBackwardAvg
and mefSoamDmHistoryStatsFrameDelayBackwardAvg counters.
bIfdvForwardBins(14)
Enables/disables the mefSoamDmCurrentStatsBinsEntry counter
and the mefSoamDmHistoryStatsBinsEntry counter
when the mefSoamDmCfgMeasBinType is 'forwardIfdv'.
bIfdvForwardMin(15)
Enables/disables the mefSoamDmCurrentStatsIfdvForwardMin
and mefSoamDmHistoryStatsIfdvForwardMin counters.
bIfdvForwardMax(16)
Enables/disables the mefSoamDmCurrentStatsIfdvForwardMax
and mefSoamDmHistoryStatsIfdvForwardMax counters.
bIfdvForwardAvg(17)
Enables/disables the mefSoamDmCurrentStatsIfdvForwardAvg
and mefSoamDmHistoryStatsIfdvForwardAvg counters.
bIfdvBackwardBins(18)
Enables/disables the mefSoamDmCurrentStatsBinsEntry counter
and the mefSoamDmHistoryStatsBinsEntry counter
when the mefSoamDmCfgMeasBinType is 'backwardIfdv'.
bIfdvBackwardMin(19)
Enables/disables the mefSoamDmCurrentStatsIfdvBackwardMin
and mefSoamDmHistoryStatsIfdvBackwardMin counters.
bIfdvBackwardMax(20)
Enables/disables the mefSoamDmCurrentStatsIfdvBackwardMax
and mefSoamDmHistoryStatsIfdvBackwardMax counters.
bIfdvBackwardAvg(21)
Enables/disables the mefSoamDmCurrentStatsIfdvBackwardAvg
and mefSoamDmHistoryStatsIfdvBackwardAvg counters.
bIfdvTwoWayBins(22)
Enables/disables the mefSoamDmCurrentStatsBinsEntry counter
and the mefSoamDmHistoryStatsBinsEntry counter
when the mefSoamDmCfgMeasBinType is 'twoWayIfdv'.
bIfdvTwoWayMin(23)
Enables/disables the mefSoamDmCurrentStatsIfdvTwoWayMin
and mefSoamDmHistoryStatsIfdvTwoWayMin counters.
bIfdvTwoWayMax(24)
Enables/disables the mefSoamDmCurrentStatsIfdvTwoWayMax
and mefSoamDmHistoryStatsIfdvTwoWayMax counters.
bIfdvTwoWayAvg(25)
Enables/disables the mefSoamDmCurrentStatsIfdvTwoWayAvg
and mefSoamDmHistoryStatsIfdvTwoWayAvg counters.
bFrameDelayRangeForwardBins(26)
Enables/disables the mefSoamDmCurrentStatsBinsEntry counter
and the mefSoamDmHistoryStatsBinsEntry counter
when the mefSoamDmCfgMeasBinType is 'forwardFrameDelayRange'.
bFrameDelayRangeForwardMax(27)
Enables/disables the mefSoamDmCurrentStatsFrameDelayRangeForwardMax
and mefSoamDmHistoryStatsFrameDelayRangeForwardMax counters.
bFrameDelayRangeForwardAvg(28)
Enables/disables the mefSoamDmCurrentStatsFrameDelayRangeForwardAvg
and mefSoamDmHistoryStatsFrameDelayRangeForwardAvg counters.
bFrameDelayRangeBackwardBins(29)
Enables/disables the mefSoamDmCurrentStatsBinsEntry counter
and the mefSoamDmHistoryStatsBinsEntry counter
when the mefSoamDmCfgMeasBinType is 'backwardFrameDelayRange'.
bFrameDelayRangeBackwardMax(30)
Enables/disables the mefSoamDmCurrentStatsFrameDelayRangeBackwardMax
and mefSoamDmHistoryStatsFrameDelayRangeBackwardMax counters.
bFrameDelayRangeBackwardAvg(31)
Enables/disables the mefSoamDmCurrentStatsFrameDelayRangeBackwardAvg
and mefSoamDmHistoryStatsFrameDelayRangeBackwardAvg counters.
bFrameDelayRangeTwoWayBins(32)
Enables/disables the mefSoamDmCurrentStatsBinsEntry counter
and the mefSoamDmHistoryStatsBinsEntry counter
when the mefSoamDmCfgMeasBinType is 'twoWayFrameDelayRange'.
bFrameDelayRangeTwoWayMax(33)
Enables/disables the mefSoamDmCurrentStatsFrameDelayRangeTwoWayMax
and mefSoamDmHistoryStatsFrameDelayRangeTwoWayMax counters.
bFrameDelayRangeTwoWayAvg(34)
Enables/disables the mefSoamDmCurrentStatsFrameDelayRangeTwoWayAvg
and mefSoamDmHistoryStatsFrameDelayRangeTwoWayAvg counters.
bMeasuredStatsFrameDelayTwoWay(35)
Enables/disables the mefSoamDmMeasuredStatsFrameDelayTwoWay
counter.
bMeasuredStatsFrameDelayForward(36)
Enables/disables the mefSoamDmMeasuredStatsFrameDelayForward
counter.
bMeasuredStatsFrameDelayBackward(37)
Enables/disables the mefSoamDmMeasuredStatsFrameDelayBackward
counter.
bMeasuredStatsIfdvTwoWay(38)
Enables/disables the mefSoamDmMeasuredStatsIfdvTwoWay
counter.
bMeasuredStatsIfdvForward(39)
Enables/disables the mefSoamDmMeasuredStatsIfdvForward
counter.
bMeasuredStatsIfdvBackward(40)
Enables/disables the mefSoamDmMeasuredStatsIfdvBackward
counter.rw Bits .1.3.6.1.4.1.15007.1.3.1.3.1.1.5 |
mefSoamDmCfgMessagePeriodThis object specifies the interval between Delay Measurement
OAM message transmission. For Delay Measurement monitoring
applications, the default value is 100ms.
This object can only be written at row creation time and cannot be
modified once it has been created.rw MefSoamTcMeasurementPeriodType UNITS "ms" .1.3.6.1.4.1.15007.1.3.1.3.1.1.6 |
mefSoamDmCfgPriorityThis object specifies the priority of frames with
Delay Measurement OAM message information.
The default value is to be the value which yields the lowest frame
loss.
This object can only be written at row creation time and cannot be
modified once it has been created.rw IEEE8021PriorityValue (IEEE8021-TC-MIB) .1.3.6.1.4.1.15007.1.3.1.3.1.1.7 |
mefSoamDmCfgFrameSizeThis object specifies the Delay Measurement frame size between
64 bytes and the maximum transmission unit of the EVC.
The range of frame sizes from 64 through 2000 octets need to be
supported, and the range of frame sizes from 2001 through 9600 octets
is suggested to be supported.
The adjustment to the frame size of the standard frame size is
accomplished by the addition of a Data or Test TLV. A Data or Test TLV
is only added to the frame if the frame size is greater than 64 bytes.
This object is only valid for the entity transmitting the Delay
Measurement frames (dmDmm, dm1DmTx) and is ignored by the entity
receiving frames.
In addition, this object is not valid when mefSoamDmCfgVersion is 0.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.3.1.1.8 |
mefSoamDmCfgDataPatternThis object specifies the DM data pattern included in a Data TLV
when the size of the DM frame is determined by the
mefSoamDmFrameSize object and mefSoamDmTestTlvIncluded is 'false'.
If the frame size object does not define the DM frame size or
mefSoamDmTestTlvIncluded is 'true' the value of this object is
ignored.
This object can only be written at row creation time and cannot be
modified once it has been created.rw MefSoamTcDataPatternType (MEF-SOAM-TC-MIB) .1.3.6.1.4.1.15007.1.3.1.3.1.1.9 |
mefSoamDmCfgTestTlvIncludedIndicates whether a Test TLV or Data TLV is included when the size
of the DM frame is determined by the mefSoamDmFrameSize object.
A value of 'true' indicates that the Test TLV is to be included. A
value of 'false' indicates that the Data TLV is to be included.
If the frame size object does not define the DM frame size
the value of this object is ignored.
This object can only be written at row creation time and cannot be
modified once it has been created.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.3.1.1.10 |
mefSoamDmCfgTestTlvPatternThis object specifies the type of test pattern to be
sent in the DM frame Test TLV when the size
of DM PDU is determined by the mefSoamDmFrameSize object and
mefSoamDmTestTlvIncluded is 'true'. If the frame size object
does not define the DM frame size or mefSoamDmTestTlvIncluded
is 'false' the value of this object is ignored.
This object can only be written at row creation time and cannot be
modified once it has been created.rw MefSoamTcTestPatternType (MEF-SOAM-TC-MIB) .1.3.6.1.4.1.15007.1.3.1.3.1.1.11 |
mefSoamDmCfgMeasurementIntervalThis object specifies a Measurement Interval in minutes.
A Measurement Interval 15 minutes needs to be supported, other intervals
may be supported.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.3.1.1.12 |
mefSoamDmCfgNumIntervalsStoredThis object specifies the number of completed Measurement Intervals
to store in the history statistic table.
At least 32 completed Measurement Intervals are to be stored. 96
Measurement Intervals are recommended to be stored.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.3.1.1.13 |
mefSoamDmCfgDestMacAddressThe Target or Destination MAC Address Field to be transmitted.
If mefSoamDmCfgType is 'dmDmm', the destination address is to be the
unicast address of the destination MEP. An error is returned if this
object is set to a multicast address.
If mefSoamDmCfgType is 'dm1DmTx', the destination address is normally the
unicast address of the destination MEP, but can be a multicast address
indicating the level of the MEG: 01-80-c2-00-00-3y, where y is the
level of the MEG. An error is returned if this object is set to any
other multicast address.
If mefSoamDmCfgType is 'dm1DmRx', this object is ignored.
This address will be used if the value of the object
mefSoamDmDestIsMepId is 'false'.
This object is only valid for the entity transmitting the
SOAM DM frames and is ignored by the entity receiving
SOAM DM frames.
This object can only be written at row creation time and cannot be
modified once it has been created.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.3.1.1.14 |
mefSoamDmCfgDestMepIdThe Maintenance Association End Point Identifier of
another MEP in the same Maintenance Association to which
the SOAM DM frame is to be sent.
This address will be used if the value of the column
mefSoamDmDestIsMepId is 'true'. A value of zero
means that the destination MEP ID has not been configured.
This object is only valid for the entity transmitting the Delay
Measurement frames, types 'dmDmm' and 'dm1DmTx'. It is not applicable
for the 'dm1DmRx' type.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Dot1agCfmMepIdOrZero .1.3.6.1.4.1.15007.1.3.1.3.1.1.15 |
mefSoamDmCfgDestIsMepIdA value of 'true' indicates that MEPID of the target MEP is used for
SOAM DM frame transmission.
A value of 'false' indicates that the destination MAC address of the
target MEP is used for SOAM DM frame transmission.
This object is only valid for the entity transmitting the Delay
Measurement frames, types 'dmDmm' and 'dm1DmTx'. It is not applicable
for the 'dm1DmRx type.
This object can only be written at row creation time and cannot be
modified once it has been created.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.3.1.1.16 |
mefSoamDmCfgSourceMacAddressThe Source MAC Address Field of the received SOAM DM session PDUs.
If mefSoamDmCfgType is dm1DmRx this object indicates the source
address of the dm1DmTx DM session.
This object is only valid for mefSoamDmCfgType set to dm1DmRx. It is
ignored for mefSoamDmCfgType set to dmDmm or dm1DmTx.
This object can only be written at row creation time and cannot be
modified once it has been created.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.3.1.1.17 |
mefSoamDmCfgStartTimeTypeThis object specifies the type of start time of the SOAM DM
session. The start time can be disabled (none), immediate, relative,
or fixed.
The value of 'none' is illegal and a write error will be returned
if this value is used.
The value of 'immediate' starts the SOAM DM session when the
mefSoamDmCfgEnabled is true.
The value of 'fixed' starts the SOAM DM session when the
mefSoamDmFixedStartDateAndTime is less than or equal to the current
system date and time and mefSoamDmCfgEnabled is true. This value is used
to implement an On-Demand fixed time PM session.
The value of 'relative' starts the SOAM DM session when the current
system date and time minus the mefSoamDmRelativeStartTime is greater than
or equal to the system date and time when the mefSoamDmStartTimeType
object was written and mefSoamDmCfgEnabled is true. This value is used
to implement an On-Demand relative time PM session.
This object can only be written at row creation time and cannot be
modified once it has been created.rw MefSoamTcOperationTimeType (MEF-SOAM-TC-MIB) .1.3.6.1.4.1.15007.1.3.1.3.1.1.18 |
mefSoamDmCfgFixedStartDateAndTimeThis object specifies the fixed start date/time for the
SOAM Delay Measurement session. This object is used only used if
mefSoamDmStartTimeType is 'fixed' and is ignored otherwise.
The default value is year 0000, month 01, day 01, time 00:00:00.00.
This object can only be written at row creation time and cannot be
modified once it has been created.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.3.1.1.19 |
mefSoamDmCfgRelativeStartTimeThis object specifies the relative start time, from
the current system time, for the SOAM DM session. This
object is used only if mefSoamDmStartTimeType is 'relative'
and is ignored otherwise.
This object can only be written at row creation time and cannot be
modified once it has been created.rw TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.3.1.1.20 |
mefSoamDmCfgStopTimeTypeThis object specifies the type of stop time to terminate the
SOAM DM session. The stop time can be forever (none), relative, or
fixed.
The value of 'none' indicates that the SOAM DM session never ends once it
has started unless the session is disabled.
The value of 'immediate' is illegal and a write error will be returned
if this value is used.
The value of 'fixed' stops the SOAM DM session when the
mefSoamDmFixedStopDateAndTime is less than or equal
to the current system date. This
value is used to implement an On-Demand fixed time PM session.
The value of 'relative' stops the SOAM DM session when the time
indicated by mefSoamDmRelativeStopTime has passed since the session
start time as determined by the mefSoamDmCfgStartTimeType,
mefSoamDmCfgFixedStartDateAndTime and mefSoamDmCfgRelativeStartTime
objects.
This value is used to implement an On-Demand relative time PM session.
This object can only be written at row creation time and cannot be
modified once it has been created.rw MefSoamTcOperationTimeType (MEF-SOAM-TC-MIB) .1.3.6.1.4.1.15007.1.3.1.3.1.1.21 |
mefSoamDmCfgFixedStopDateAndTimeThis object specifies the fixed stop date/time for the
SOAM Delay Measurement session. This object is used only used
if mefSoamDmStopTimeType is 'fixed' and is ignored otherwise.
The default value is year 0000, month 01, day 01, time 00:00:00.00.
This object can only be written at row creation time and cannot be
modified once it has been created.rw DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.3.1.1.22 |
mefSoamDmCfgRelativeStopTimeThis object specifies the relative stop time, from the
session start time, to stop the SOAM DM session. This
object is used only if mefSoamDmStopTimeType is 'relative' and is
ignored otherwise.
This object can only be written at row creation time and cannot be
modified once it has been created.rw TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.3.1.1.23 |
mefSoamDmCfgRepetitionTimeThis object specifies a configurable repetition time between
Measurement Intervals in a Delay Measurement session in seconds.
If the value is 0 (none), there is no time gap between the end of one
Measurement Interval and the start of a new Measurement Interval.
This is the normal usage case.
If the value is greater than one Measurement Interval there is time gap
between the end of one Measurement Interval and the start of the next
Measurement Interval. The repetition time specifies the time between
the start of consecutive Measurement Intervals; hence the gap between
the end of one Measurement Interval and the start of the next is equal
to the difference between the repetition time and the measurement
interval. During this gap, no SOAM PDUs are sent for this session and
no measurements are made.
If the value is greater 0 but less than or equal to the measurement
interval, an error is returned.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.3.1.1.24 |
mefSoamDmCfgAlignMeasurementIntervalsThis object specifies whether the Measurement Intervals for
the Delay Measurement session are aligned with a zero offset to
real time.
The value 'true' indicates that each Measurement Interval starts
at a time which is aligned to NE time source hour, if the repetition
time (or the Measurement Interval, if the repetition time is 0) is
a factor of an hour, i.e. 60min/15min = 4. For instance, a
Measurement Interval/Repetition Time of 15 minutes would stop/start
the Measurement Interval at 0, 15, 30, and 45 minutes of an hour. A
Measurement Interval/Repetition Time of 7 minutes would not align
to the hour since 7 minutes is NOT a factor of an hour, i.e.
60min/7min = 8.6. In this case the behavior is the same as if the
object is set to 'false'.
The value 'false' indicates that the first Measurement Interval starts
at an arbitrary time and each subsequent Measurement Interval starts
at a time which is determined by mefSoamLmCfgRepetitionTime.
This object can only be written at row creation time and cannot be
modified once it has been created.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.3.1.1.25 |
mefSoamDmCfgAlignMeasurementOffsetThis object specifies the offset in minutes from the time of day value
if mefSoamDmCfgAlignMeasurementIntervals is 'true' and the repetition
time is a factor of 60 minutes. If not, the value of this object
is ignored.
If the Measurement Interval is 15 minutes and
mefSoamDmCfgAlignMeasurementIntervals is true and if this object was
set to 5 minutes, the Measurement Intervals would start at 5, 20, 35, 50
minutes past each hour.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.3.1.1.26 |
mefSoamDmCfgNumMeasBinsPerFrameDelayIntervalThis object specifies the number of measurement bins
per Measurement Interval for Frame Delay measurements.
At least 3 bins are to be supported; at least 10 bins are recommended
to be supported.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.3.1.1.27 |
mefSoamDmCfgNumMeasBinsPerInterFrameDelayVariationIntervalThis object specifies the number of measurement bins
per Measurement Interval for Inter-Frame Delay Variation
measurements.
The minimum number of measurement bins to be supported is 2. The
desired number of measurements bins to be supported is 10.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.3.1.1.28 |
mefSoamDmCfgInterFrameDelayVariationSelectionOffsetThis object specifies the selection offset for
Inter-Frame Delay Variation measurements. If this value
is set to n, then the IFDV is calculated by taking the
difference in frame delay between frame F and frame (F+n).
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.3.1.1.29 |
mefSoamDmCfgNumMeasBinsPerFrameDelayRangeIntervalThis object specifies the number of measurement bins
per Measurement Interval for Frame Delay Range measurements.
At least 2 bins are to be supported; at least 10 bins are recommended
to be supported.
This object can only be written at row creation time and cannot be
modified once it has been created.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.3.1.1.30 |
mefSoamDmCfgSessionTypeThis object indicates whether the current session is defined to
be 'Proactive' or 'On-Demand'. A value of 'proactive'
indicates the current session is 'Proactive'. A value of 'onDemand'
indicates the current session is 'On-Demand'.
This object can only be written at row creation time and cannot be
modified once it has been created.rw MefSoamTcSessionType (MEF-SOAM-TC-MIB) .1.3.6.1.4.1.15007.1.3.1.3.1.1.31 |
mefSoamDmCfgSessionStatusThis object indicates the current status of the DM session. A value
of 'active' indicates the current DM session is active, i.e. the current
time lies between the start time and the stop time, and
mefSoamDmCfgEnabled is true. A value of 'notActive' indicates the
current DM session is not active, i.e. it has not started yet, has
stopped upon reaching the stop time, or is disabled.ro MefSoamTcStatusType (MEF-SOAM-TC-MIB) .1.3.6.1.4.1.15007.1.3.1.3.1.1.32 |
mefSoamDmCfgHistoryClearThis object when written clears the Delay Measurement history
tables (mefSoamDmHistoryStatsTable and mefSoamDmHistoryStatsBinsTable)
- all rows are deleted. When read the value always returns 'false'.
Writing this value does not change the current stat table,
nor any of the items in the configuration table.
Writing this object at row creation has no effect.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.3.1.1.33 |
mefSoamDmCfgRowStatusThe status of the row.
The writable columns in a row cannot be changed if the row
is active, except for mefSoamDmCfgEnabled and mefSoamDmCfgHistoryClear
objects. All columns are to have a valid value before a row
can be activated.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.3.1.1.34 |
mefSoamDmCfgMeasBinTableThis table includes configuration objects for the Delay Measurement
bins to collect stats.
Each row in the table is automatically created when the Delay
Measurement session is defined for the selected MEP. The number of rows
created is based upon three items: the DM type, the number of bins
defined for each type, and whether bins are enabled for each type.
The first four indices are the same as used to create the DM session:
Maintenance Domain, MaNet, MEP identification, and mefSoamDmCfgIndex. The
fifth index is the type of bin, and the sixth index is the bin number.
For a dmDmm session all nine types of bins can be created. For a dm1DmmTx
session no bins are created. For a dm1DmmRx session only types
forwardFrameDelay, forwardIfdv, and forwardFrameDelayRange can be created.
The number of bins created for a bin type is based upon: the
mefSoamDmCfgNumMeasBinsPerFrameDelayInterval object, the
mefSoamDmCfgNumMeasBinsPerInterFrameDelayVariationInterval object, the
mefSoamDmCfgNumMeasBinsPerFrameDelayRangeInterval object, and
the mefSoamDmCfgMeasurementEnable object.
For instance, if a dmDmm session with Bins per Frame Delay Interval
set to 5, Bins per Frame Delay Variation Interval set to 3, and Frame
Delay Range set to 2 (default), all of the appropriate bits set in
mefSoamDmMeasurementCfgEnable, the following number of rows would be
created:
For bin types TwoWayFrameDelay(1), forwardFrameDelay(2), and
backwardFrameDelay(3) = 5 bins * 3 types = 15 rows
For bin types TwoWayIfdv(4), forwardIfdv(5), backwardIfdv(6) =
3 bins * 3 types = 9 rows.
For bins types twoWayFrameDelayRange(7), forwardFrameDelayRange(8),
backwardFrameDelayRange(9) =
2 bins * 3 types = 6 rows.
This gives a total of 30 rows created for the DMM session example.
Each value in the bin defaults to 5000us greater than the previous bin,
with the first bin default value set to 0.
For the delay example above (5 bins), the following default values
would be written to the bins:
bin 1: 0 (range is 0us <= measurement < 5,000us)
bin 2: 5000 (range is 5,000us <= measurement < 10,000us)
bin 3: 10000 (range is 10,000us <= measurement < 15,000us)
bin 4: 15000 (range is 15,000us <= measurement < 20,000us)
bin 5: 20000 (range is 20,000us <= measurement < infinity)
For the delay variation example above (3 bins), the following default
values would be written to the bins:
bin 1: 0 (range is 0us <= measurement < 5,000us)
bin 2: 5000 (range is 5,000us <= measurement < 10,000us)
bin 3: 10000 (range is 10,000us <= measurement < infinity)
For the frame delay range example above (2 bins), the following default
values would be written to the bins:
bin 1: 0 (range is 0us <= measurement < 5,000us)
bin 2: 5000 (range is 5,000us <= measurement < infinity)
The writable objects in this table need to be persistent upon reboot
or restart of a device.
Rows are only created if the corresponding measurement type has been enabled
via the mefSoamDmCfgMeasurementEnable object. SEQUENCE OF MefSoamDmCfgMeasBinEntry .1.3.6.1.4.1.15007.1.3.1.3.2 |
mefSoamDmCfgMeasBinEntryThe conceptual row of mefSoamDmCfgMeasBinTable. MefSoamDmCfgMeasBinEntry .1.3.6.1.4.1.15007.1.3.1.3.2.1 |
mefSoamDmCfgMeasBinTypeThis object specifies whether the bin number is for
Frame Delay or Inter-Frame Delay Variation. MefSoamTcDelayMeasurementBinType (MEF-SOAM-TC-MIB) .1.3.6.1.4.1.15007.1.3.1.3.2.1.1 |
mefSoamDmCfgMeasBinNumberThis object specifies the bin number for the
configured boundary. The first bin has bin number 1. Unsigned32 .1.3.6.1.4.1.15007.1.3.1.3.2.1.2 |
mefSoamDmCfgMeasBinLowerBoundThis object specifies the lower boundary for a
measurement bin. The upper boundary is defined by the next bin
value or infinite for the last bin defined.
The measurement boundary for each measurement bin is to
be larger than the measurement boundary of the preceding
measurement bin. By default, the next bin is set to 5000us larger
than the lower bin boundary.
The values in a bin boundary object represents the time range
used to segregate delay data into the appropriate statistical
data bin. For five bins with default values, each bin has the
following time range:
bin 1 = 0, range is 0us <= measurement < 5,000us
bin 2 = 5000, range is 5,000us <= measurement < 10,000us
bin 3 = 10000, range is 10,000us <= measurement < 15,000us
bin 4 = 15000, range is 15,000us <= measurement < 20,000us
bin 5 = 20000, range is 20,000us <= measurement < infinity
The first bin boundary (mefSoamDmCfgBinNumber set to 1) always contains
the value of 0. Attempting to write a non-zero value to this bin will
result in an error.rw Unsigned32 UNITS "microseconds (us)" .1.3.6.1.4.1.15007.1.3.1.3.2.1.3 |
mefSoamDmMeasuredStatsTableThis object contains the last measured results for a SOAM Delay
Measurement session.
Each row in the table represents a Delay Measurement session for
the defined MEP. This table uses four indices. The first three indices
are the indices of the Maintenance Domain, MaNet, and MEP tables. The
fourth index is the specific DM session on the selected MEP.
Instances of this managed object are created automatically
by the SNMP Agent when the Delay Measurement session is running.
Each object in this table applies only if the corresponding bit is set in
mefSoamDmCfgMeasurementEnable.
The objects in this table do not need to be persistent upon reboot or restart
of a device. SEQUENCE OF MefSoamDmMeasuredStatsEntry .1.3.6.1.4.1.15007.1.3.1.3.3 |
mefSoamDmMeasuredStatsEntryThe conceptual row of mefSoamDmMeasuredStatsTable MefSoamDmMeasuredStatsEntry .1.3.6.1.4.1.15007.1.3.1.3.3.1 |
mefSoamDmMeasuredStatsFrameDelayTwoWayThis object contains the two-way frame delay calculated by this
MEP from the last received SOAM PDU.
This object is undefined is mefSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.3.1.1 |
mefSoamDmMeasuredStatsFrameDelayForwardThis object contains the frame delay in the forward direction
calculated by this MEP from the last received SOAM PDU. The value of this
object may not be accurate in the absence of sufficiently precise clock
synchronization.
This object is undefined is mefSoamDmCfgType is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.3.1.2 |
mefSoamDmMeasuredStatsFrameDelayBackwardThis object contains the frame delay in the backward direction
calculated by this MEP from the last received SOAM PDU. The value of this
object may not be accurate in the absence of sufficiently precise clock
synchronization.
This object is undefined is mefSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.3.1.3 |
mefSoamDmMeasuredStatsIfdvTwoWayThis object contains the last two-way inter-frame delay
interval calculated by this MEP.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.3.1.4 |
mefSoamDmMeasuredStatsIfdvForwardThis object contains the last one-way inter-frame delay
interval in the forward direction calculated by this MEP.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.3.1.5 |
mefSoamDmMeasuredStatsIfdvBackwardThis object contains the last one-way inter-frame delay
interval in the backward direction calculated by this MEP.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.3.1.6 |
mefSoamDmCurrentStatsTableThis table contains the results for the current Measurement
Interval in a SOAM Delay Measurement session gathered during the interval
indicated by mefSoamLmCfgMeasurementInterval.
A row in this table is created automatically
by the SNMP Agent when the Delay Measurement session is configured.
Each row in the table represents the current statistics for a Delay
Measurement session for the defined MEP. This table uses four indices.
The first three indices are the indices of the Maintenance Domain, MaNet,
and MEP tables. The fourth index is the specific DM session on the
selected MEP. There can be more than one DM session per MEP.
The objects in this table apply regardless of the value of
mefSoamDmCfgType unless otherwise specified in the object description.
Backward and two-way statistic objects are undefined if mefSoamDmCfgType
is dm1DmRx.
Except for mefSoamDmCurrentStatsIndex, mefSoamDmCurrentStatsStartTime
mefSoamDmCurrentStatsElapsedTime and mefSoamDmCurrentStatsSuspect,
each object in this table applies only if the corresponding bit is set in
mefSoamDmCfgMeasurementEnable.
The objects in this table do not need to be persistent upon reboot or
restart of a device. SEQUENCE OF MefSoamDmCurrentStatsEntry .1.3.6.1.4.1.15007.1.3.1.3.4 |
mefSoamDmCurrentStatsEntryThe conceptual row of mefSoamDmCurrentStatsTable MefSoamDmCurrentStatsEntry .1.3.6.1.4.1.15007.1.3.1.3.4.1 |
mefSoamDmCurrentStatsIndexThe index for the current Measurement Interval for this
PM session. This value will become the value for
mefSoamDmHistoryStatsIndex once the Measurement Interval
is completed.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.3.4.1.1 |
mefSoamDmCurrentStatsStartTimeThe time that the current Measurement Interval started.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.3.4.1.2 |
mefSoamDmCurrentStatsElapsedTimeThe time that the current Measurement Interval has been running, in 0.01
seconds.ro TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.3.4.1.3 |
mefSoamDmCurrentStatsSuspectWhether the Measurement Interval has been marked as suspect.
The object is to be set to false at the start of a measurement
interval. It is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts servicero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.3.4.1.4 |
mefSoamDmCurrentStatsFrameDelayTwoWayMinThis object contains the minimum two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is mefSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.5 |
mefSoamDmCurrentStatsFrameDelayTwoWayMaxThis object contains the maximum two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is mefSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.6 |
mefSoamDmCurrentStatsFrameDelayTwoWayAvgThis object contains the average two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is mefSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.7 |
mefSoamDmCurrentStatsFrameDelayForwardMinThis object contains the minimum one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is mefSoamDmCfgType is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.8 |
mefSoamDmCurrentStatsFrameDelayForwardMaxThis object contains the maximum one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is mefSoamDmCfgType is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.9 |
mefSoamDmCurrentStatsFrameDelayForwardAvgThis object contains the average one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is mefSoamDmCfgType is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.10 |
mefSoamDmCurrentStatsFrameDelayBackwardMinThis object contains the minimum one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is mefSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.11 |
mefSoamDmCurrentStatsFrameDelayBackwardMaxThis object contains the maximum one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is mefSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.12 |
mefSoamDmCurrentStatsFrameDelayBackwardAvgThis object contains the average one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is mefSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.13 |
mefSoamDmCurrentStatsIfdvForwardMinThis object contains the minimum one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.14 |
mefSoamDmCurrentStatsIfdvForwardMaxThis object contains the maximum one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.15 |
mefSoamDmCurrentStatsIfdvForwardAvgThis object contains the average one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.16 |
mefSoamDmCurrentStatsIfdvBackwardMinThis object contains the minimum one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.17 |
mefSoamDmCurrentStatsIfdvBackwardMaxThis object contains the maximum one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.18 |
mefSoamDmCurrentStatsIfdvBackwardAvgThis object contains the average one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.19 |
mefSoamDmCurrentStatsIfdvTwoWayMinThis object contains the minimum two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.20 |
mefSoamDmCurrentStatsIfdvTwoWayMaxThis object contains the maximum two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.21 |
mefSoamDmCurrentStatsIfdvTwoWayAvgThis object contains the average two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.22 |
mefSoamDmCurrentStatsFrameDelayRangeForwardMaxThis object contains the maximum one-way frame delay range
in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.23 |
mefSoamDmCurrentStatsFrameDelayRangeForwardAvgThis object contains the average one-way frame delay range
in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.24 |
mefSoamDmCurrentStatsFrameDelayRangeBackwardMaxThis object contains the maximum one-way frame delay range
in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.25 |
mefSoamDmCurrentStatsFrameDelayRangeBackwardAvgThis object contains the average one-way frame delay range
in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.26 |
mefSoamDmCurrentStatsFrameDelayRangeTwoWayMaxThis object contains the maximum two-way frame delay range
calculated by this MEP for this Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.27 |
mefSoamDmCurrentStatsFrameDelayRangeTwoWayAvgThis object contains the average two-way frame delay range
calculated by this MEP for this Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.4.1.28 |
mefSoamDmCurrentStatsSoamPdusSentThis object contains the count of the number of SOAM PDUs sent
during this Measurement Interval.
This object applies when mefSoamDmCfgType is dmDmm or dm1DmTx and
is undefined if mefSoamDmCfgType is dm1DmRx. It indicates the
number of DMM or 1DM SOAM frames transmitted.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.3.4.1.29 |
mefSoamDmCurrentStatsSoamPdusReceivedThis object contains the count of the number of SOAM
PDUs received in this Measurement Interval.
This object indicates the number of DMR and 1DM SOAM frames
received. This object applies when mefSoamDmCfgType is dmDmm or
dm1DmRx and is undefined if mefSoamDmCfgType is dm1DmTx.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.3.4.1.30 |
mefSoamDmCurrentStatsBinsTableThis table contains the result bins for the current Measurement
Interval in a SOAM Delay Measurement session.
Each row in the table represents the current bin statistics for a
Delay Measurement session for the defined MEP. This table uses six
indices. The first three indices are the indices of the Maintenance
Domain, MaNet, and MEP tables. The fourth index is the specific DM
session on the selected MEP. The fifth index indicates bin type and
the sixth indicates the specific bin number.
A row in this table is created automatically by the SNMP Agent when
the Delay Measurement session is configured and the bin counter value
is set to 0.
The objects in this table are ignored if mefSoamDmCfgType is 1DmTx.
This table applies only if the corresponding bit is set in
mefSoamDmCfgMeasurementEnable.
The objects in this table do not need to be persistent upon reboot
or restart of a device. SEQUENCE OF MefSoamDmCurrentStatsBinsEntry .1.3.6.1.4.1.15007.1.3.1.3.5 |
mefSoamDmCurrentStatsBinsEntryThe conceptual row of mefSoamDmCurrentStatsBinsTable MefSoamDmCurrentStatsBinsEntry .1.3.6.1.4.1.15007.1.3.1.3.5.1 |
mefSoamDmCurrentStatsBinsCounterThis object contains the count of the number of completed
measurements initiated in this Measurement Interval whose value
falls within the range specified for this bin (that is, greater
than or equal to the measurement boundary for the bin, and
(unless the bin is the last bin) less than the measurement
boundary for the following bin.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.3.5.1.1 |
mefSoamDmHistoryStatsTableThis table contains the results for history Measurement
Intervals in a SOAM Delay Measurement session.
Rows of this table are created automatically
by the SNMP Agent when the Delay Measurement session is running and a
Measurement Interval is completed.
Each row in the table represents the Measurement Interval history
statistics for a Delay Measurement session for the defined MEP. This
table uses five indices. The first three indices are the indices of
the Maintenance Domain, MaNet, and MEP tables. The fourth index is the
specific DM session on the selected MEP. The fifth index is the
Measurement Interval.
At least 32 completed Measurement Intervals are to be supported. 96
completed Measurement Intervals are recommended to be supported. If
there are at least 32 rows in the table and a new Measurement Interval
completes and a new row is to be added to the table, the oldest completed
Measurement Interval can be deleted (row deletion). If the measurement
interval is other than 15 minutes then a minimum of 8 hours of
completed Measurement Intervals are to be supported and 24 hours are
recommended to be supported.
The objects in this table apply regardless of the value of
mefSoamDmCfgType unless otherwise specified in the object description.
Backward and two-way statistic objects are undefined if mefSoamDmCfgType
is dm1DmRx.
Except for mefSoamDmHistoryStatsIndex, mefSoamDmHistoryStatsEndTime,
mefSoamDmHistoryStatsElapsedTime and mefSoamDmHistoryStatsSuspect,
each object in this table applies only if the corresponding bit is set in
mefSoamDmCfgMeasurementEnable.
The rows and objects in this table are to be persistent upon reboot
or restart of a device. SEQUENCE OF MefSoamDmHistoryStatsEntry .1.3.6.1.4.1.15007.1.3.1.3.6 |
mefSoamDmHistoryStatsEntryThe conceptual row of mefSoamDmHistoryStatsTable MefSoamDmHistoryStatsEntry .1.3.6.1.4.1.15007.1.3.1.3.6.1 |
mefSoamDmHistoryStatsIndexThe index for the Measurement Interval within this
PM session.
Measurement Interval indexes are assigned sequentially by
the SNMP Agent. The first Measurement Interval that occurs after
the session is started is assigned index 1.
Referential integrity is necessary, i.e., the index needs to be
persistent upon a reboot or restart of a device. The index
is never reused while this session is active until it wraps to zero.
The index value keeps increasing up to that time. Unsigned32 .1.3.6.1.4.1.15007.1.3.1.3.6.1.1 |
mefSoamDmHistoryStatsEndTimeThe time that the Measurement Interval ended.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.3.6.1.2 |
mefSoamDmHistoryStatsElapsedTimeThe length of time that the Measurement Interval ran for,
in 0.01 seconds.ro TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.3.6.1.3 |
mefSoamDmHistoryStatsSuspectWhether the Measurement Interval has been marked as suspect.
The object is set to true when there is a discontinuity in the
performance measurements during the Measurement Interval. Conditions
for a discontinuity include, but are not limited to the following:
1 - The local time-of-day clock is adjusted by at least 10 seconds
2 - The conducting of a performance measurement is halted before the
current Measurement Interval is completed
3 - A local test, failure, or reconfiguration that disrupts servicero TruthValue (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.3.6.1.4 |
mefSoamDmHistoryStatsFrameDelayTwoWayMinThis object contains the minimum two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is mefSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.5 |
mefSoamDmHistoryStatsFrameDelayTwoWayMaxThis object contains the maximum two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is mefSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.6 |
mefSoamDmHistoryStatsFrameDelayTwoWayAvgThis object contains the average two-way frame delay
calculated by this MEP for this Measurement Interval.
This object is undefined is mefSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.7 |
mefSoamDmHistoryStatsFrameDelayForwardMinThis object contains the minimum one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is mefSoamDmCfgType is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.8 |
mefSoamDmHistoryStatsFrameDelayForwardMaxThis object contains the maximum one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is mefSoamDmCfgType is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.9 |
mefSoamDmHistoryStatsFrameDelayForwardAvgThis object contains the average one-way frame delay
in the forward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is mefSoamDmCfgType is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.10 |
mefSoamDmHistoryStatsFrameDelayBackwardMinThis object contains the minimum one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is mefSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.11 |
mefSoamDmHistoryStatsFrameDelayBackwardMaxThis object contains the maximum one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is mefSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.12 |
mefSoamDmHistoryStatsFrameDelayBackwardAvgThis object contains the average one-way frame delay
in the backward direction calculated by this MEP for this
Measurement Interval. The value of this object may not be accurate
in the absence of sufficiently precise clock synchronization.
This object is undefined is mefSoamDmCfgType is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.13 |
mefSoamDmHistoryStatsIfdvForwardMinThis object contains the minimum one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.14 |
mefSoamDmHistoryStatsIfdvForwardMaxThis object contains the maximum one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.15 |
mefSoamDmHistoryStatsIfdvForwardAvgThis object contains the average one-way inter-frame delay
interval in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.16 |
mefSoamDmHistoryStatsIfdvBackwardMinThis object contains the minimum one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.17 |
mefSoamDmHistoryStatsIfdvBackwardMaxThis object contains the maximum one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.18 |
mefSoamDmHistoryStatsIfdvBackwardAvgThis object contains the average one-way inter-frame delay
interval in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.19 |
mefSoamDmHistoryStatsIfdvTwoWayMinThis object contains the minimum two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.20 |
mefSoamDmHistoryStatsIfdvTwoWayMaxThis object contains the maximum two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.21 |
mefSoamDmHistoryStatsIfdvTwoWayAvgThis object contains the average two-way inter-frame delay
interval calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.22 |
mefSoamDmHistoryStatsFrameDelayRangeForwardMaxThis object contains the maximum one-way Frame Delay Range
in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.23 |
mefSoamDmHistoryStatsFrameDelayRangeForwardAvgThis object contains the average one-way Frame Delay Range
in the forward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.24 |
mefSoamDmHistoryStatsFrameDelayRangeBackwardMaxThis object contains the maximum one-way Frame Delay Range
in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.25 |
mefSoamDmHistoryStatsFrameDelayRangeBackwardAvgThis object contains the average one-way Frame Delay Range
in the backward direction calculated by this MEP for this
Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.26 |
mefSoamDmHistoryStatsFrameDelayRangeTwoWayMaxThis object contains the maximum two-way Frame Delay Range
calculated by this MEP for this Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.27 |
mefSoamDmHistoryStatsFrameDelayRangeTwoWayAvgThis object contains the average two-way Frame Delay Range
calculated by this MEP for this Measurement Interval.
The value of this object is undefined when mefSoamDmCfgType
is dm1DmTx or dm1DmRx.ro Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.6.1.28 |
mefSoamDmHistoryStatsSoamPdusSentThis object contains the count of the number of SOAM PDUs sent
during this Measurement Interval.
This object applies when mefSoamDmCfgType is dmDmm or dm1DmTx and
is undefined if mefSoamDmCfgType is dm1DmRx. It indicates the
number of DMM or 1DM SOAM frames transmitted.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.3.6.1.29 |
mefSoamDmHistoryStatsSoamPdusReceivedThis object contains the count of the number of SOAM
PDUs received in this Measurement Interval.
This object indicates the number of DMR and 1DM SOAM frames
received. This object applies when mefSoamDmCfgType is dmDmm or
dm1DmRx and is undefined if mefSoamDmCfgType is dm1DmTx.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.3.6.1.30 |
mefSoamDmHistoryStatsBinsTableThis table contains the result bins for the history Measurement
Intervals in a SOAM Delay Measurement session.
Rows of this table are created automatically
by the SNMP Agent when the Delay Measurement session is running and a
Measurement Interval is completed.
Each row in the table represents the Measurement Interval history
statistics for a specific bin in a Delay Measurement session for the
defined MEP. This table uses seven indices. The first three indices
are the indices of the Maintenance Domain, MaNet, and MEP tables. The
fourth index is the specific DM session on the selected MEP. The
fifth index is the Measurement Interval. The sixth index is the
specific bin type. The seventh index is the specific bin number.
Rows in this table pertaining to a given Measurement Interval are
deleted when (and only when) the corresponding row in the
mefSoamDmHistoryStatsTable is deleted.
The objects in this table are ignored if mefSoamDmCfgType is 1DmTx.
This table applies only if the corresponding bit is set in
mefSoamDmCfgMeasurementEnable.
The objects in this table need to be persistent upon reboot
or restart of a device. SEQUENCE OF MefSoamDmHistoryStatsBinsEntry .1.3.6.1.4.1.15007.1.3.1.3.7 |
mefSoamDmHistoryStatsBinsEntryThe conceptual row of mefSoamDmHistoryStatsBinsTable MefSoamDmHistoryStatsBinsEntry .1.3.6.1.4.1.15007.1.3.1.3.7.1 |
mefSoamDmHistoryStatsBinsCounterThis object contains the count of the number of completed
measurements initiated in this Measurement Interval whose value
falls within the range specified for this bin (that is, greater
than or equal to the measurement boundary for the bin, and
(unless the bin is the last bin) less than the measurement
boundary for the following bin.ro Gauge32 .1.3.6.1.4.1.15007.1.3.1.3.7.1.1 |
mefSoamDmThresholdCfgTableThis table contains the list of Delay Measurement threshold configuration
values for DM Performance Monitoring.
The main purpose of the threshold configuration table is to configure
threshold alarm notifications indicating that a specific performance
metric is not being met.
Each row in the table represents a Delay Measurement session threshold
set for the defined MEP. This table uses five indices. The first three
indices are the indices of the Maintenance Domain, MaNet, and MEP tables.
The fourth index is the specific DM session on the selected MEP. The
fifth index is the specific threshold set number.
Rows in this table are not created automatically. A row is created in
this table to set up a threshold set on a configured MEP that has a
configured DM session.
An NE needs to support at least one threshold set for NE SOAM PM compliance. A
second threshold set on the NE is desirable. More than two threshold
sets on the NE can be configured if supported on the NE.
All the objects in the row have a default value that disables the
particular threshold measurement. In order to enable a threshold
measurement the particular bit in the mefSoamDmThresholdCfgEnable object
is to be set to '1' and the selected threshold measurement is to have
a threshold value configured. Non-configured threshold measurements
are disabled by default.
The writable objects in this table need to be persistent upon reboot
or restart of a device. SEQUENCE OF MefSoamDmThresholdCfgEntry .1.3.6.1.4.1.15007.1.3.1.3.8 |
mefSoamDmThresholdCfgEntryThe conceptual row of mefSoamDmThresholdCfgTable. MefSoamDmThresholdCfgEntry .1.3.6.1.4.1.15007.1.3.1.3.8.1 |
mefSoamDmThresholdCfgIndexThe index of the threshold number for the specific DM
threshold entry.
An index value of '1' is to be supported. Other index values
can be supported. Unsigned32 .1.3.6.1.4.1.15007.1.3.1.3.8.1.1 |
mefSoamDmThresholdCfgEnableA vector of bits that indicates the type of SOAM DM threshold
notifications that are enabled.
A bit set to '1' enables the specific SOAM DM threshold notification
and when the specific counter is enabled and the threshold is crossed a
notification is generated.
A bit set to '0' disables the specific SOAM DM threshold notification.
If a particular SOAM DM threshold is not supported the BIT value is
set to '0'.
bMefSoamDmMeasuredFrameDelayTwoWayThreshold(0)
Enables/disables measured frame two-way delay threshold
notification. The notification is sent immediately when the
mefSoamDmMeasuredStatsFrameDelayTwoWay value is
greater than or equal to threshold value.
bMefSoamDmMaxFrameDelayTwoWayThreshold(1)
Enables/disables maximum frame two-way delay threshold
notification. The notification is sent immediately when the
mefSoamDmCurrentStatsFrameDelayTwoWayMax value is
greater than or equal to threshold value in a Measurement Interval.
bMefSoamDmAvgFrameDelayTwoWayThreshold(2)
Enables/disables average frame two-way delay threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
mefSoamDmCurrentStatsFrameDelayTwoWayAvg value is
greater than or equal to the threshold value.
bMefSoamDmMeasuredIfdvTwoWayThreshold(3)
Enables/disables measured frame IFDV two-way threshold
notification. The notification is sent immediately when the
mefSoamDmMeasuredStatsIfdvTwoWay value is greater
than or equal to threshold value.
bMefSoamDmMaxIfdvTwoWayThreshold(4)
Enables/disables maximum frame IFDV two-way threshold
notification. The notification is sent immediately when the
mefSoamDmCurrentStatsIfdvTwoWayMax value is greater
than or equal to threshold value in a Measurement Interval.
bMefSoamDmAvgIfdvTwoWayThreshold(5)
Enables/disables average frame IFDV two-way threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
mefSoamDmCurrentStatsIfdvTwoWayAvg value is
greater than or equal to the threshold value.
bMefSoamDmMaxFrameDelayRangeTwoWayThreshold(6)
Enables/disables maximum Frame Delay Range two-way threshold
notification. The notification is sent immediately when the
mefSoamDmCurrentStatsFrameDelayRangeTwoWayMax value is greater
than or equal to threshold value in a Measurement Interval.
bMefSoamDmAvgFrameDelayRangeTwoWayThreshold(7)
Enables/disables average Frame Delay Range two-way threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
mefSoamDmCurrentStatsFrameDelayRangeTwoWayAvg value is
greater than or equal to the threshold value.
bMefSoamDmMeasuredFrameDelayForwardThreshold(8)
Enables/disables measured forward frame delay threshold
notification. The notification is sent immediately when the
mefSoamDmMeasuredStatsFrameDelayForward value is
greater than or equal to threshold value.
bMefSoamDmMaxFrameDelayForwardThreshold(9)
Enables/disables maximum forward frame delay threshold
notification. The notification is sent immediately when the
mefSoamDmCurrentStatsFrameDelayForwardMax value is
greater than or equal to threshold value in a Measurement Interval.
bMefSoamDmAvgFrameDelayForwardThreshold(10)
Enables/disables average forward frame delay threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
mefSoamDmCurrentStatsFrameDelayForwardAvg value is
greater than or equal to the threshold value.
bMefSoamDmMeasuredIfdvForwardThreshold(11)
Enables/disables measured frame IFDV forward threshold
notification. The notification is sent immediately when the
mefSoamDmMeasuredStatsIfdvForward value is greater
than or equal to threshold value.
bMefSoamDmMaxIfdvForwardThreshold(12)
Enables/disables maximum frame IFDV forward threshold
notification. The notification is sent immediately when the
mefSoamDmCurrentStatsIfdvForwardMax value is greater
than or equal to threshold value in a Measurement Interval.
bMefSoamDmAvgIfdvForwardThreshold(13)
Enables/disables average frame IFDV forward threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
mefSoamDmCurrentStatsIfdvForwardAvg value is
greater than or equal to the threshold value.
bMefSoamDmMaxFrameDelayRangeForwardThreshold(14)
Enables/disables maximum Frame Delay Range forward threshold
notification. The notification is sent immediately when the
mefSoamDmCurrentStatsFrameDelayRangeForwardMax value is greater
than or equal to threshold value in a Measurement Interval.
bMefSoamDmAvgFrameDelayRangeForwardThreshold(15)
Enables/disables average Frame Delay Range forward threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
mefSoamDmCurrentStatsFrameDelayRangeForwardAvg value is
greater than or equal to the threshold value.
bMefSoamDmMeasuredFrameDelayBackwardThreshold(16)
Enables/disables measured backward frame delay threshold
notification. The notification is sent immediately when the
mefSoamDmMeasuredStatsFrameDelayBackward value is
greater than or equal to threshold value.
bMefSoamDmMaxFrameDelayBackwardThreshold(17)
Enables/disables maximum backward frame delay threshold
notification. The notification is sent immediately when the
mefSoamDmCurrentStatsFrameDelayBackwardMax value is
greater than or equal to threshold value in a
Measurement Interval.
bMefSoamDmAvgFrameDelayBackwardThreshold(18)
Enables/disables average backward frame delay threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
mefSoamDmCurrentStatsFrameDelayBackwardAvg value is
greater than or equal to the threshold value.
bMefSoamDmMeasuredIfdvBackwardThreshold(19)
Enables/disables measured frame IFDV backward threshold
notification. The notification is sent immediately when the
mefSoamDmMeasuredStatsIfdvBackward value is greater
than or equal to threshold value.
bMefSoamDmMaxIfdvBackwardThreshold(20)
Enables/disables maximum frame IFDV backward threshold
notification. The notification is sent immediately when the
mefSoamDmCurrentStatsIfdvBackwardMax value is greater
than or equal to threshold value in a Measurement Interval.
bMefSoamDmAvgIfdvBackwardThreshold(21)
Enables/disables average frame IFDV backward threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
mefSoamDmCurrentStatsIfdvBackwardAvg value is greater
than or equal to the threshold value.
bMefSoamDmMaxFrameDelayRangeBackwardThreshold(22)
Enables/disables maximum Frame Delay Range backward threshold
notification. The notification is sent immediately when the
mefSoamDmCurrentStatsFrameDelayRangeBackwardMax value is greater
than or equal to threshold value in a Measurement Interval.
bMefSoamDmAvgFrameDelayRangeBackwardThreshold(23)
Enables/disables average Frame Delay Range backward threshold
notification. The notification is sent when at the end of a
Measurement Interval if the
mefSoamDmCurrentStatsFrameDelayRangeBackwardAvg value is greater
than or equal to the threshold value.rw Bits .1.3.6.1.4.1.15007.1.3.1.3.8.1.2 |
mefSoamDmThresholdCfgMeasuredFrameDelayTwoWayThresholdThis object is used to set the measurement two-way delay threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.3 |
mefSoamDmThresholdCfgMaxFrameDelayTwoWayThresholdThis object is used to set the maximum two-way delay threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.4 |
mefSoamDmThresholdCfgAvgFrameDelayTwoWayThresholdThis object is used to set the average two-way delay threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.5 |
mefSoamDmThresholdCfgMeasuredIfdvTwoWayThresholdThis object is used to set the measurement two-way IFDV threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.6 |
mefSoamDmThresholdCfgMaxIfdvTwoWayThresholdThis object is used to set the maximum two-way IFDV threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.7 |
mefSoamDmThresholdCfgAvgIfdvTwoWayThresholdThis object is used to set the average two-way IFDV threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.8 |
mefSoamDmThresholdCfgMaxFrameDelayRangeTwoWayThresholdThis object is used to set the maximum two-way Frame Delay Range threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.9 |
mefSoamDmThresholdCfgAvgFrameDelayRangeTwoWayThresholdThis object is used to set the average two-way Frame Delay Range threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.10 |
mefSoamDmThresholdCfgMeasuredFrameDelayForwardThresholdThis object is used to set the measurement forward delay threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.11 |
mefSoamDmThresholdCfgMaxFrameDelayForwardThresholdThis object is used to set the maximum forward delay threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.12 |
mefSoamDmThresholdCfgAvgFrameDelayForwardThresholdThis object is used to set the average forward delay threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.13 |
mefSoamDmThresholdCfgMeasuredIfdvForwardThresholdThis object is used to set the measurement IFDV threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.14 |
mefSoamDmThresholdCfgMaxIfdvForwardThresholdThis object is used to set the maximum IFDV threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.15 |
mefSoamDmThresholdCfgAvgIfdvForwardThresholdThis object is used to set the average IFDV threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.16 |
mefSoamDmThresholdCfgMaxFrameDelayRangeForwardThresholdThis object is used to set the maximum Frame Delay Range threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.17 |
mefSoamDmThresholdCfgAvgFrameDelayRangeForwardThresholdThis object is used to set the average Frame Delay Range threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.18 |
mefSoamDmThresholdCfgMeasuredFrameDelayBackwardThresholdThis object is used to set the measurement backward delay threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.19 |
mefSoamDmThresholdCfgMaxFrameDelayBackwardThresholdThis object is used to set the maximum backward delay threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.20 |
mefSoamDmThresholdCfgAvgFrameDelayBackwardThresholdThis object is used to set the average backward delay threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.21 |
mefSoamDmThresholdCfgMeasuredIfdvBackwardThresholdThis object is used to set the measurement backward IFDV threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.22 |
mefSoamDmThresholdCfgMaxIfdvBackwardThresholdThis object is used to set the maximum backward IFDV threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.23 |
mefSoamDmThresholdCfgAvgIfdvBackwardThresholdThis object is used to set the average backward IFDV threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.24 |
mefSoamDmThresholdCfgMaxFrameDelayRangeBackwardThresholdThis object is used to set the maximum backward Frame Delay Range threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.25 |
mefSoamDmThresholdCfgAvgFrameDelayRangeBackwardThresholdThis object is used to set the average backward Frame Delay Range threshold
value that will be used to determine if a threshold notification is
generated.rw Unsigned32 UNITS "microseconds" .1.3.6.1.4.1.15007.1.3.1.3.8.1.26 |
mefSoamDmThresholdCfgRowStatusThe status of the row.
The writable columns in a row cannot be changed if the row
is active. All columns are to have a valid value before a row
can be activated.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.3.8.1.27 |
mefSoamPmNotificationCfg OBJECT IDENTIFIER .1.3.6.1.4.1.15007.1.3.1.4 |
mefSoamPmNotificationCfgAlarmIntervalA value indicating the shortest time interval in seconds between the
generation of the same notification type per PM session to the list of
notification destinations. An agent generates the first notification
of given type for a given PM session immediately. An agent is not to
generate a second specific notification of the same type for the same
MEP for the same session until the time interval has expired. A value of zero
indicates that all notifications are sent immediately upon detection
of the condition.rw Unsigned32 .1.3.6.1.4.1.15007.1.3.1.4.1 |
mefSoamPmNotificationCfgAlarmEnableA vector of bits that indicates whether a specific notification is
enabled.
A bit set to '1' enables the specific notification generation.
A bit set to '0' disables the specific notification.
If a particular alarm is not supported the BIT value of the enable/disable
is set to '0'.
bAvailabilityChangeAlarm(0) enables/disables mefSoamAvailabilityChangeAlarm
bLmSessionStartStopAlarm(1) enables/disables mefSoamLmSessionStartStopAlarm
bDmSessionStartStopAlarm(2) enables/disables mefSoamDmSessionStartStopAlarm
bPmThresholdAboveAlarm(3) enables/disables mefSoamPmThresholdAboveAlarm
bPmThresholdSetClearAlarm(4) enables/disables mefSoamPmThresholdSetClearAlarmrw Bits .1.3.6.1.4.1.15007.1.3.1.4.2 |
mefSoamPmNotificationObj OBJECT IDENTIFIER .1.3.6.1.4.1.15007.1.3.1.5 |
mefSoamPmNotificationObjDateAndTimeThis object contains the time and date at the time that
the notification event is detected, not the time of the notification
generation.
This object is used only for notifications. The mechanism to set and keep
current the date and time is not specified.ro DateAndTime (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.5.1 |
mefSoamPmNotificationObjThresholdIdThe Object Identifier of the object that caused the generation of the
notification from the mefSoamLmThresholdEntry or mefSoamDmThresholdEntry.
This object is only used for the notification.ro OBJECT IDENTIFIER .1.3.6.1.4.1.15007.1.3.1.5.2 |
mefSoamPmNotificationObjThresholdConfigThe configured threshold value of the object that caused the generation
of the notification.
This object is only used for the notification.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.5.3 |
mefSoamPmNotificationObjThresholdValueThe measured value of the object at the time of the generation of the
Notification, from the mefSoamLmMeasuredStatsTable,
mefSoamLmCurrentStatsTable, mefSoamLmCurrentAvailStatsTable,
mefSoamDmMeasuredStatsTable or mefSoamDmCurrentStatsTable.
This object is only used for the notification.ro Unsigned32 .1.3.6.1.4.1.15007.1.3.1.5.4 |
mefSoamPmNotificationObjSuspectThe suspect flag for the current Measurement Interval in which the
notification was generated from the mefSoamLmCurrentStatsTable,
mefSoamLmCurrentAvailStatsTable, or mefSoamDmCurrentStatsTable.
This object is only used for the notification.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.5.5 |
mefSoamPmNotificationObjCrossingTypeThe Notification Crossing Type of the object that caused the generation
of the notification from the mefSoamLmThresholdEntry or
mefSoamDmThresholdEntry.
aboveAlarm(1) indicates that the crossing type alarm was an above
threshold
setAlarm(2) indicates that the crossing type alarm was a set
threshold
clearAlarm(3) indicates that the crossing type alarm was a clear
threshold
This object is only used for the notification.ro Enumeration .1.3.6.1.4.1.15007.1.3.1.5.6 |
mefSoamPmNotificationObjDestinationMepThe MAC address of the Destination MEP associated the notification found
in either the mefSoamDmCfgTable or mefSoamLmCfgTable.
This object is only used for the notification.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.5.7 |
mefSoamPmNotificationObjPriorityThe CoS priority of the associated notification found
in either the mefSoamDmCfgTable or mefSoamLmCfgTable.
This object is only used for the notification.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.15007.1.3.1.5.8 |
mefSoamPmMibConformance OBJECT IDENTIFIER .1.3.6.1.4.1.15007.1.3.2 |
mefSoamPmMibCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.15007.1.3.2.1 |
mefSoamPmMibGroups OBJECT IDENTIFIER .1.3.6.1.4.1.15007.1.3.2.2 |