LINK-PROBE-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
425
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
425 total| Object Name |
|---|
netQuest OBJECT IDENTIFIER .1.3.6.1.4.1.568 |
link-probe OBJECT IDENTIFIER .1.3.6.1.4.1.568.8 |
pvcNotAvailDCEThis trap is generated when a PVC's unavailability is exceed the
preset threshold due to the network fault. TRAP-TYPE .1.3.6.1.4.1.568.8.0.1 |
pvcNotAvailDTEThis trap is generated when a PVC's unavailability is exceed the
preset threshold due to the local DTE fault. TRAP-TYPE .1.3.6.1.4.1.568.8.0.2 |
pvcRTDThis trap is generated when a PVC's average round trap delay (RTD) is
exceed the preset threshold. TRAP-TYPE .1.3.6.1.4.1.568.8.0.3 |
frChanUtilizeToDTEThis trap is generated when channel utilization to DTE direction
is exceed the preset threshold. TRAP-TYPE .1.3.6.1.4.1.568.8.0.4 |
frChanUtilizeToDCEThis trap is generated when channel utilization to DCE direction
is exceed the preset threshold. TRAP-TYPE .1.3.6.1.4.1.568.8.0.5 |
pvcBecnThis trap is generated when a PVC's BECNs is exceed
the preset threshold within current interval. TRAP-TYPE .1.3.6.1.4.1.568.8.0.6 |
pvcFecnThis trap is generated when a PVC's FECNs is exceed
the preset threshold within current interval. TRAP-TYPE .1.3.6.1.4.1.568.8.0.7 |
pvcUtilToDTEThis trap is generated when a PVC's utilization is exceeding
the preset threshold within current interval. TRAP-TYPE .1.3.6.1.4.1.568.8.0.8 |
pvcUtilToDCEThis trap is generated when a PVC's utilization is exceeding
the preset threshold within current interval. TRAP-TYPE .1.3.6.1.4.1.568.8.0.9 |
pvcCIRExceedToDTEThis trap is generated when the octets transmitted to the network
direction is exceeding the CIR within current interval. TRAP-TYPE .1.3.6.1.4.1.568.8.0.10 |
pvcEIRExceedToDTEThis trap is generated when the octets transmitted to the network
direction is exceeding the EIR within current interval. TRAP-TYPE .1.3.6.1.4.1.568.8.0.11 |
pvcLossFrameTxThis trap is generated when frames were lost in the transmission
direction within current interval. TRAP-TYPE .1.3.6.1.4.1.568.8.0.12 |
pvcLossFrameRxThis trap is generated when frames were lost in the receiving
direction within current interval. TRAP-TYPE .1.3.6.1.4.1.568.8.0.13 |
frChanUtilToDTE-exceptionThis trap will be sent at any time in two cases:
1. The channel utilization to DTE (measured in TC) is exceeding
the threshold if such trap never be sent in this interval or
the frChanUtilToDTE-endException trap was just sent;
2. The variation of the channel utilization to DTE is exceeding
the trapRange if such trap has just be sent. TRAP-TYPE .1.3.6.1.4.1.568.8.0.14 |
frChanUtilToDCE-exceptionThis trap will be sent at any time in two cases:
1. The channel utilization to DCE (measured in TC) is exceeding
the threshold if such trap never be sent in this interval or
the frChanUtilToDTE-endException trap was just sent;
2. The variation of the channel utilization to DCE is exceeding
the trapRange if such trap has just be sent. TRAP-TYPE .1.3.6.1.4.1.568.8.0.15 |
frChanUtilToDTE-endExceptionThis trap will be sent if the channel utilization to DTE (measured in TC)
is changed back below the threshold. TRAP-TYPE .1.3.6.1.4.1.568.8.0.16 |
frChanUtilToDCE-endExceptionThis trap will be sent if the channel utilization to DCE (measured in TC)
is changed back below the threshold. TRAP-TYPE .1.3.6.1.4.1.568.8.0.17 |
pvcRTD-exceptionThis trap will be sent at any time in two cases:
1. The PVC RTD real time value (measured at every Poll interval) is
exceeding the threshold if such trap never be sent in this interval
or the pvcRTD-endException trap was just sent;
2. The variation of the pvc-RTD-realTime is exceeding
the trapRange if such trap has just be sent. TRAP-TYPE .1.3.6.1.4.1.568.8.0.18 |
pvcRTD-endExceptionThis trap will be sent if the PVC DTD real time (measured at every Poll
interval) is changed back below the threshold. TRAP-TYPE .1.3.6.1.4.1.568.8.0.19 |
pvcLoadToDTE-exceptionThis trap will be sent at any time at these two cases:
1. The PVC load to DTE real time value (measured in TC ) is
exceeding the threshold if such trap has never be sent in this
interval or the pvcLoadToDTE-endException trap was just sent;
2. The variation of the pvc-load-toDTE-realTime is exceeding
the trapRange if such trap has just be sent. TRAP-TYPE .1.3.6.1.4.1.568.8.0.20 |
pvcLoadToDCE-exceptionThis trap will be sent at any time at these two cases:
1. The PVC load to DCE real time value (measured in TC, ) is
exceeding the threshold if such trap has never be sent in this
interval or the pvcLoadToDCE-endException trap was just sent;
2. The variation of the pvc-load-toDCE-realTime is exceeding
the trapRange if such trap has just be sent. TRAP-TYPE .1.3.6.1.4.1.568.8.0.21 |
pvcLoadToDTE-endExceptionThis trap will be sent if the PVC load to DTE real time (measured in TC)
is changed back below the threshold. TRAP-TYPE .1.3.6.1.4.1.568.8.0.22 |
pvcLoadToDCE-endExceptionThis trap will be sent if the PVC load to DCE real time (measured in TC)
is changed back below the threshold. TRAP-TYPE .1.3.6.1.4.1.568.8.0.23 |
pvcStatusChangeAvailThis trap is generated when a PVC status changes from unavailable to
available. TRAP-TYPE .1.3.6.1.4.1.568.8.0.24 |
pvcStatusChangeUnavailThis trap is generated when a PVC status changes from available to
unavailable, or from valid to invalid (PVC becomes deleted). TRAP-TYPE .1.3.6.1.4.1.568.8.0.25 |
dbuPvcStatusChangeBackedUpThis trap is generated when a DBU PVC status changes
to backed-up. TRAP-TYPE .1.3.6.1.4.1.568.8.0.26 |
dbuPvcStatusChangeNotBackedUpThis trap is generated when a DBU PVC status changes
to not backed-up. TRAP-TYPE .1.3.6.1.4.1.568.8.0.27 |
dbuBackupCallActivationThis trap is generated when a back-up call is activated. TRAP-TYPE .1.3.6.1.4.1.568.8.0.28 |
dbuBackupCallDeactivationThis trap is generated when a back-up call is deactivated. TRAP-TYPE .1.3.6.1.4.1.568.8.0.29 |
dbuBackupCallFailedThis trap is generated when a back-up call failed to activate. TRAP-TYPE .1.3.6.1.4.1.568.8.0.30 |
dcdAlarmDetectionThis trap is generated when a DCD alarm is detected. TRAP-TYPE .1.3.6.1.4.1.568.8.0.31 |
cp3000EventThis trap is the CP-3000 compliant Log Event trap, generated
when a Device or PVC specific status change occurs. TRAP-TYPE .1.3.6.1.4.1.568.8.0.32 |
bypassEnabledThis trap is generated when frame relay automatically enables
frame relay data BYPASS. TRAP-TYPE .1.3.6.1.4.1.568.8.0.33 |
probeConfig OBJECT IDENTIFIER .1.3.6.1.4.1.568.8.1 |
chan-config OBJECT IDENTIFIER .1.3.6.1.4.1.568.8.1.1 |
lmi-OperationLMI operation, on disabledrw Enumeration .1.3.6.1.4.1.568.8.1.1.1 |
lmi-DLCILMI DLCI can just take two values: DLCI 0 or DLCI 1023,
default is 0.rw Enumeration .1.3.6.1.4.1.568.8.1.1.2 |
inband-IP-DLCIvalid Inband IP DLCI ranges from 16 to 991, read only
objectrw INTEGER .1.3.6.1.4.1.568.8.1.1.3 |
ip-EncapsuIndicate which IP DLCI Encapsulation methodrw Enumeration .1.3.6.1.4.1.568.8.1.1.4 |
interface-SpeedInterface Speed is n*8 kpbs, the default value is
64 kbps.rw Enumeration .1.3.6.1.4.1.568.8.1.1.5 |
nvram-updateThis object lets the user decide if he (she) wants to write the
just modified parameters in channel configuration group to nvram,
if he chose 'write', these parameters will be updated; and if he
chose 'restore', the modifications are lost.rw Enumeration .1.3.6.1.4.1.568.8.1.1.6 |
lmi-config OBJECT IDENTIFIER .1.3.6.1.4.1.568.8.1.2 |
lmi-typeThis object identifies the LMI type the network is currently
using, read/write object.rw Enumeration .1.3.6.1.4.1.568.8.1.2.1 |
max-Info-LengthMaximum supported frame information length ranges from
400 to 4000, the default value is 4000.rw INTEGER ( 400..4000 ) .1.3.6.1.4.1.568.8.1.2.2 |
n391-CounterN391 Counter ranges from 1 to 255, the default value is 6.rw INTEGER ( 1..255 ) .1.3.6.1.4.1.568.8.1.2.3 |
n392-Net-CounterN392 Net Counter ranges from 1 to 10, the default
value is 3.rw INTEGER ( 1..10 ) .1.3.6.1.4.1.568.8.1.2.4 |
n392-User-CounterN392 User Counter ranges from 1 to 10, the default
value is 3.rw INTEGER ( 1..10 ) .1.3.6.1.4.1.568.8.1.2.5 |
n393-Net-CounterN393 Net Counter ranges from 1 to 10, the default
value is 4.rw INTEGER ( 1..10 ) .1.3.6.1.4.1.568.8.1.2.6 |
n393-User-CounterN393 User Counter ranges from 1 to 10, the default
value is 4.rw INTEGER ( 1..10 ) .1.3.6.1.4.1.568.8.1.2.7 |
t391-TimerT391 Timer ranges from 5 to 30, the default value is 10,
which would always less than or equal to T392 Timer.rw INTEGER ( 5..30 ) .1.3.6.1.4.1.568.8.1.2.8 |
t392-TimerT392 Timer ranges from 5 to 30, the default value is 15.
which should always greater than T391 Timer.rw INTEGER ( 5..30 ) .1.3.6.1.4.1.568.8.1.2.9 |
lMI-ControllerThis object lets the user decide if he (she) wants
to update the just modified LMI parameters, only when
the user chooses to update will the new parameters be
accepted by the system. If the user selects the
restoreParam value then the LMI parameters will revert
to the previous values, and the modifications are lost.rw Enumeration .1.3.6.1.4.1.568.8.1.2.10 |
pro-fun-config OBJECT IDENTIFIER .1.3.6.1.4.1.568.8.1.3 |
softwareVersionThis object displays the software version we are currently
running, so according to the version number, the user can
determine which version is newer.ro DisplayString .1.3.6.1.4.1.568.8.1.3.1 |
probe-ModeProbe mode defines whether the link probe is generator,
responder, both or disabled.rw Enumeration .1.3.6.1.4.1.568.8.1.3.2 |
poll-Periodpoll period defines the frequency of sending the polling frame
by the link probe. The value is between 1 to 60 sec. The poll
period applies to all PVCs that are to be probed.rw INTEGER ( 1..60 ) .1.3.6.1.4.1.568.8.1.3.3 |
sys-current-timesys-current-time displays the system current time
with 4 digits year, 2 digits month, 2 digits date and
hours, minutes and seconds, which are each 2 digits. If the
user wants to set the current time, he (she) must follow
the correct formats.rw DisplayString .1.3.6.1.4.1.568.8.1.3.4 |
current-intv-start-timecurrent-intv-start-time displays the current interval starting
time with 4 digits year, 2 digits month, 2 digits date and
hours, minutes and seconds, which are each 2 digits.ro DisplayString .1.3.6.1.4.1.568.8.1.3.5 |
pvc-CountPVC count defines the total number of PVCs which are to be
probed. The value is between 1 to 20.ro INTEGER ( 1..20 ) .1.3.6.1.4.1.568.8.1.3.6 |
probeTokenSizeThis object defines the probe token size.rw INTEGER ( 19..4096 ) .1.3.6.1.4.1.568.8.1.3.7 |
pvc-addThis object allows the user to add a PVC to the existing PVC
table, the added PVC must not exist before it is added.rw INTEGER ( 16..991 ) .1.3.6.1.4.1.568.8.1.3.8 |
pvc-deleteThis object allows the user to delete a PVC from the existing PVC
table, the deleted PVC must exist before it was deleted.rw INTEGER ( 16..991 ) .1.3.6.1.4.1.568.8.1.3.9 |
pvc-TablePVC table, which lists PVCs that currently are probed. SEQUENCE OF PVC-Entry .1.3.6.1.4.1.568.8.1.3.10 |
pvc-EntryIdentifies an entry (row) in PVC table. PVC-Entry .1.3.6.1.4.1.568.8.1.3.10.1 |
pvc-Table-IndexIdentifies an entry (row) in PVC table.ro INTEGER ( 16..991 ) .1.3.6.1.4.1.568.8.1.3.10.1.1 |
pvc-OperationThis object identifies the three possible states which a pvc
can be in, '1' means we are just collecting the statistical data
for this PVC, '2' means we are not just collecting statistic
data for this PVC, but also put it into a pending table waiting
for probe, '3' means this PVC is used for both collecting
statistic data and probing. Even though we can view three
states for this PVC, we can just set '1' or '2' for this PVC.rw Enumeration .1.3.6.1.4.1.568.8.1.3.10.1.2 |
pvc-Remote-IpAddressThis object defines the IP address of the remote probe used
with IP monitoring.ro IpAddress .1.3.6.1.4.1.568.8.1.3.10.1.3 |
alternateVersionThis object displays the software version we are not currently
running, so according to the version number, the user can
determine which version is newer.ro DisplayString .1.3.6.1.4.1.568.8.1.3.11 |
bypassStatusThis object identifies the three possible states which data bypass
can be in. '1' means frame relay data bypass is off.
'2' means frame relay data bypass is on.
'3' means frame relay data bypass is on and was set on
automatically because there was no DCD and no RTS.
State '1' can only be set if state is '2'.
State '2' can only be set if state is '1'.
State '3' cannot be set manually.rw Enumeration .1.3.6.1.4.1.568.8.1.3.12 |
trap-config OBJECT IDENTIFIER .1.3.6.1.4.1.568.8.1.4 |
trapCtlGlobalThis object is used to enable or disable system traps. Only when
it is enabled, the standard traps, such as cold start trap, warm
start trap; and enterprise specific traps can be sent.rw Enumeration .1.3.6.1.4.1.568.8.1.4.1 |
trapCtlSpecificThis parameter is a bitmap for the 16 enterprise specific traps,
zero means all the traps are disabled and 0xffff means all
the traps are enabled. The following lists
the 16 bits which are defined:
1st bit = pvcNotAvailDCE-trap;
2nd bit = pvcNotAvailDTE-trap;
3rd bit = pvcAveRTD-trap;
4th bit = frChanUtilizeToDTE-trap;
5th bit = frChanUtilizeToDCE-trap;
6th bit = pvcBecn-trap;
7th bit = pvcFecn-trap;
8th bit = pvcUtilToDTE-trap;
9th bit = pvcUtilToDCE-trap;
10th bit = pvcCIRExceed-trap;
11th bit = pvcEIRExceed-trap;
12th bit = pvcLossFrameTx-trap;
13th bit = pvcLossFrameRx-trap;
14th bit = all real-time exception and endOfException traps;
15th bit = pvcStatusChange;
16th bit = dbuTrapsEnable;rw INTEGER .1.3.6.1.4.1.568.8.1.4.2 |
pvcNotAvailThreshDCEThis parameter defines the allowed maximum PVC not availability
threshold within current time interval due to a network fault.
It is expressed as a percentage of full interval time. If the
actual average value is more than this threshold, a trap will
be sent at the end of the interval.rw INTEGER .1.3.6.1.4.1.568.8.1.4.3 |
pvcNotAvailThreshDTEThis parameter defines the allowed maximum PVC not availability
threshold within current time interval due to the local DTE fault.
It is expressed as a percentage of full interval time. If the actual
average value is more than this threshold, a trap will be sent at
the end of the interval.rw INTEGER .1.3.6.1.4.1.568.8.1.4.4 |
pvcAveRTDThreshThis parameter defines the allowed maximum PVC round trip time delay
(milliseconds) within the current time interval. If the actual average
round trip delay is more than this threshold, a trap will be sent at
the end of the interval.rw INTEGER .1.3.6.1.4.1.568.8.1.4.5 |
frChanUtilizThreshToDTEThis parameter defines the maximum allowed frame relay channel
utilization to the DTE direction. It is expressed in percentage.
If the actual average utilization is more than this threshold,
a trap will be sent at the end of the interval.rw INTEGER .1.3.6.1.4.1.568.8.1.4.6 |
frChanUtilizThreshToDCEThis parameter defines the maximum allowed frame relay channel
utilization to the DCE direction. It is expressed in percentage.
If the actual average utilization is more than this threshold,
a trap will be sent at the end of the interval.rw INTEGER .1.3.6.1.4.1.568.8.1.4.7 |
pvcBecnThreshThis parameter defines the maximum allowed BECNs for a PVC
within current interval. If the actual BECNs are more than this
threshold, a trap will be sent at the end of the interval.rw INTEGER .1.3.6.1.4.1.568.8.1.4.8 |
pvcFecnThreshThis parameter defines the maximum allowed FECNs for a PVC
within current interval. If the actual FECNs are more than this
threshold, a trap will be sent at the end of the interval.rw INTEGER .1.3.6.1.4.1.568.8.1.4.9 |
pvcUtilToDTEThreshThis parameter defines the maximum allowed PVC utilization to DTE
within current interval. If the actual average utilization is more
than this threshold, a trap will be sent at the end of the interval.rw INTEGER .1.3.6.1.4.1.568.8.1.4.10 |
pvcUtilToDCEThreshThis parameter defines the maximum allowed PVC utilization to DCE
within current interval. If the actual average utilization is more
than this threshold, a trap will be sent at the end of the interval.rw INTEGER .1.3.6.1.4.1.568.8.1.4.11 |
chanLoadToDTEThresh-realTimeThis parameter defines the maximum allowed real-time channel
load to the DTE direction (calculated within every TC). It is
expressed in percentage. If the actual load is more than this
threshold, an exception trap will be sent immediately.rw INTEGER .1.3.6.1.4.1.568.8.1.4.12 |
chanLoadToDCEThresh-realTimeThis parameter defines the maximum allowed real-time channel
load to the DCE direction (calculated within every TC). It is
expressed in percentage. If the actual load is more than this,
threshold, an exception trap will be sent immediately.rw INTEGER .1.3.6.1.4.1.568.8.1.4.13 |
chanLoadThreshToDTE-realTimeRangeThis parameter defines the variation range for real-time channel
load to the DTE exception trap. If within the current TC interval,
the variation of the actual utilization is more than that range
compared with previous trap value, another exception trap will be
sent immediately. This variation range is defined in percentage.rw INTEGER .1.3.6.1.4.1.568.8.1.4.14 |
chanLoadThreshToDCE-realTimeRangeThis parameter defines the variation range for real-time channel
load to the DCE exception trap. If within the current TC interval,
the variation of the actual utilization is more than that range
compared with previous trap value, another exception trap will be
sent immediately. This variation range is defined in percentage.rw INTEGER .1.3.6.1.4.1.568.8.1.4.15 |
pvcRTDThresh-realTimeThis parameter defines the maximum allowed real-time PVC
Round Trip Delay in msec., it is calculated as the same frequency
as the Probe Polls (1 to 60 sec.). If the actual RTD is more than
this threshold, an exception trap will be sent immediately.rw INTEGER .1.3.6.1.4.1.568.8.1.4.16 |
pvcRTDThresh-realTimeRangeThis parameter defines the variation range for real-time PVC
RTD exception trap. If the variation of the current RTD value
is more than this range compared with previous trap value, another
exception trap or endOfException will be sent immediately. This
variation range is defined in percentage.rw INTEGER .1.3.6.1.4.1.568.8.1.4.17 |
pvcLoadToDTEThresh-realTimeThis parameter defines the maximum allowed real-time PVC
load to the DTE direction (calculated within every TC). It is
expressed in percentage. If the actual load is more than this
threshold, an exception trap will be sent immediately.rw INTEGER .1.3.6.1.4.1.568.8.1.4.18 |
pvcLoadToDCEThresh-realTimeThis parameter defines the maximum allowed real-time PVC
load to the DCE direction (calculated within every TC). It is
expressed in percentage. If the actual load is more than this
threshold, an exception trap will be sent immediately.rw INTEGER .1.3.6.1.4.1.568.8.1.4.19 |
pvcLoadToDTEThresh-realTimeRangeThis parameter defines the variation range for real-time PVC
load to the DTE exception trap. If within the current TC interval,
the variation of the actual utilization is more than that range
compared with previous trap value, another exception trap will be
sent immediately. This variation range is defined in percentage.rw INTEGER .1.3.6.1.4.1.568.8.1.4.20 |
pvcLoadToDCEThresh-realTimeRangeThis parameter defines the variation range for real-time PVC
load to the DCE exception trap. If within the current TC interval,
the variation of the actual utilization is more than that range
compared with previous trap value, another exception trap will be
sent immediately. This variation range is defined in percentage.rw INTEGER .1.3.6.1.4.1.568.8.1.4.21 |
pvc-config OBJECT IDENTIFIER .1.3.6.1.4.1.568.8.1.5 |
pvcTCThis parameter defines the committed rate measurement
time interval (in 1/10 second) which can be calculated as
Bc/CIR. For example, if we want TC to be 1 sec., this object
should be set as 10.rw INTEGER .1.3.6.1.4.1.568.8.1.5.1 |
pvcCirEir-TablePVC table, which lists PVCs for which the statistical data
are collected. SEQUENCE OF PvcCirEir-Entry .1.3.6.1.4.1.568.8.1.5.2 |
pvcCirEir-EntryIdentifies an entry (row) in PVC CIR/EIR table. PvcCirEir-Entry .1.3.6.1.4.1.568.8.1.5.2.1 |
pvcCirEir-Table-IndexIdentifies an entry (row) in PVC table.ro INTEGER ( 16..991 ) .1.3.6.1.4.1.568.8.1.5.2.1.1 |
pvcCirToDTEThis parameter defines the committed information rate (bps)
under normal condition in the direction of to DTE.rw INTEGER .1.3.6.1.4.1.568.8.1.5.2.1.2 |
pvcCirToDCEThis parameter defines the committed information rate (bps)
under normal condition in the direction of to DCE.rw INTEGER .1.3.6.1.4.1.568.8.1.5.2.1.3 |
pvcEirToDTEThis parameter defines the maximum transfer information rate
(bps) which the network is accepting in the direction of
to DTE.rw INTEGER .1.3.6.1.4.1.568.8.1.5.2.1.4 |
pvcEirToDCEThis parameter defines the maximum transfer information rate
(bps) which the network is accepting in the direction of
to DCE.rw INTEGER .1.3.6.1.4.1.568.8.1.5.2.1.5 |
file-download-config OBJECT IDENTIFIER .1.3.6.1.4.1.568.8.1.6 |
sourceIpAddressThis object defines the IP address of the place where the
updated file would store, currently we use a long integer
to display.rw IpAddress .1.3.6.1.4.1.568.8.1.6.1 |
sourceFileNameThis object defines the name of the updated file.rw DisplayString .1.3.6.1.4.1.568.8.1.6.2 |
sourceFileModeThis object defines the mode of the updated file.rw Enumeration .1.3.6.1.4.1.568.8.1.6.3 |
tftpActionThis object defines the action we will take of TFTP.rw Enumeration .1.3.6.1.4.1.568.8.1.6.4 |
changeVersionThis object is related to the next software reset object, the user
can change the version of software and reset it. If in the middle
of a TFTP transfer, this object cannot be set. It also
cannot be set to switchVersion if there is no other
version to which to switch. An undefined value of 0 is also
sameVersion.rw Enumeration .1.3.6.1.4.1.568.8.1.6.5 |
softwareResetThis object is related to the previous software version object, the
user can choose the version of software and reset it. If in the middle
of a TFTP transfer, this object can not be set.rw Enumeration .1.3.6.1.4.1.568.8.1.6.6 |
tftpStateThis object defines the current state of the TFTP download.ro Enumeration .1.3.6.1.4.1.568.8.1.6.7 |
net-management-config OBJECT IDENTIFIER .1.3.6.1.4.1.568.8.1.7 |
ipInterfaceThis object defines the type of IP interface currently used in
the system. pppIpInterface is an asynchronous ppp interface and
isdnIpInterface is a synchronous ppp interface.rw Enumeration .1.3.6.1.4.1.568.8.1.7.1 |
inbandIpAddressThis object defines the IP address of the probe over the
inband interface. Even though separate from outbandIpAddress,
this address only used when ipInterface is inbandIpInterface.ro IpAddress .1.3.6.1.4.1.568.8.1.7.2 |
outbandIpAddressThis object defines the IP address of the probe over the
current out of band interface: asynchronous ppp, ethernet,
or synchronous ppp over ISDN.ro IpAddress .1.3.6.1.4.1.568.8.1.7.3 |
routerIpAddressThis object defines the default gateway or next-hop IP address
which is used when no route is found.ro IpAddress .1.3.6.1.4.1.568.8.1.7.4 |
subnetmaskIpAddressThis object defines the network Id portion of our inbandIpAddress
or outbandIpAddress.ro IpAddress .1.3.6.1.4.1.568.8.1.7.5 |
probeStat OBJECT IDENTIFIER .1.3.6.1.4.1.568.8.2 |
chStCurrent OBJECT IDENTIFIER .1.3.6.1.4.1.568.8.2.1 |
dte-frames-ch-currIdentifies total frames received from DTE device within
current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.1.1 |
dce-frames-ch-currIdentifies total frames received from DCE device within
current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.1.2 |
dte-octets-ch-currIdentifies total octets received from DTE device within
current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.1.3 |
dce-octets-ch-currIdentifies total octets received from DTE device within
current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.1.4 |
lmi-enq-tx-ch-currIdentifies the total number of LMI enquiries sent to DCE
within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.1.5 |
lmi-resp-tx-ch-currIdentifies the total number of LMI responses sent to DTE
within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.1.6 |
lmi-enq-rx-ch-currIdentifies the total number of LMI enquiries from the DTE
within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.1.7 |
lmi-resp-rx-ch-currIdentifies the total number of LMI status responses received
from the DCE within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.1.8 |
fecn-frames-ch-currIdentifies total number of frames with FECN set received
within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.1.9 |
becn-frames-ch-currIdentifies total number of frames with BECN set received
within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.1.10 |
ip-tx-ch-currIdentifies total number of IP packets sent on inband DLCI
within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.1.11 |
ip-rx-ch-currIdentifies total number of IP packets received on inband
DLCI within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.1.12 |
poll-tx-ch-currIdentifies total number of probe polls sent to DCE within
current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.1.13 |
resp-tx-ch-currIdentifies total number of probe responses sent to DCE
within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.1.14 |
poll-rx-ch-currIdentifies total number of probe polls received from DCE
within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.1.15 |
resp-rx-ch-currIdentifies total number of probe responses received from
DCE within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.1.16 |
chStInterval-Tableprobe statistic table, row 1 to row 96,
which defines the time interval for every 15
minutes. SEQUENCE OF ChStInterval-Entry .1.3.6.1.4.1.568.8.2.2 |
chStInterval-EntryIdentifies an entry (row) in probe statistic table. ChStInterval-Entry .1.3.6.1.4.1.568.8.2.2.1 |
chStIntv-indexIdentifies an entry (row) in channel statistic table,
1-96 time intervals.ro INTEGER ( 1..96 ) .1.3.6.1.4.1.568.8.2.2.1.1 |
dte-frames-ch-intvIdentifies total frames received from DTE device within a 15
minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.2.1.2 |
dce-frames-ch-intvIdentifies total frames received from DCE device within a 15
minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.2.1.3 |
dte-octets-ch-intvIdentifies total octets received from DTE device within a 15
minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.2.1.4 |
dce-octets-ch-intvIdentifies total octets received from DTE device within a 15
minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.2.1.5 |
lmi-enq-tx-ch-intvIdentifies the total number of LMI enquiries sent to DCE
within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.2.1.6 |
lmi-resp-tx-ch-intvIdentifies the total number of LMI responses send to
DTE within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.2.1.7 |
lmi-enq-rx-ch-intvIdentifies the total number of LMI enquiries received
within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.2.1.8 |
lmi-resp-rx-ch-intvIdentifies the total number of LMI status responses received
from the DCE within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.2.1.9 |
fecn-frames-ch-intvIdentifies total number of frames with FECN set received within a 15
minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.2.1.10 |
becn-frames-ch-intvIdentifies total number of frames with BECN set received within a 15
minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.2.1.11 |
ip-tx-ch-intvIdentifies total number of IP packets sent on inband DLCI
within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.2.1.12 |
ip-rx-ch-intvIdentifies total number of IP packets received on inband
DLCI within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.2.1.13 |
poll-tx-ch-intvIdentifies total number of probe polls sent to DCE within
a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.2.1.14 |
resp-tx-ch-intvIdentifies total number of probe response sent to DCE within
a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.2.1.15 |
poll-rx-ch-intvIdentifies total number of probe polls received from DCE
within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.2.1.16 |
resp-rx-ch-intvIdentifies total number of probe responses received from
DCE within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.2.1.17 |
pvcStCurrent-TablePVC statistic table. SEQUENCE OF PVCStCurrent-entry .1.3.6.1.4.1.568.8.2.3 |
pvcStCurrent-EntryIdentifies an entry (row) in PVC statistic table PVCStCurrent-entry .1.3.6.1.4.1.568.8.2.3.1 |
pvc-number-index-currIndex in PVC statistics table, which identifies
the PVC number, up to 20 PVCs can exist.ro INTEGER ( 16..991 ) .1.3.6.1.4.1.568.8.2.3.1.1 |
dte-frames-pvc-currIdentifies total frames received from DTE device for a
specific PVC within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.3.1.2 |
dce-frames-pvc-currIdentifies total frames received from DCE device for a
specific PVC within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.3.1.3 |
dte-octets-pvc-currIdentifies total octets received from DTE device for a
specific PVC within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.3.1.4 |
dce-octets-pvc-currIdentifies total octets received from DTE device for a
specific PVC within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.3.1.5 |
dte-frames-with-DE-pvc-currIdentifies total frames with DE bit set received from DTE device
for a specific PVC within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.3.1.6 |
dce-frames-with-DE-pvc-currIdentifies total frames with DE bit set received from DCE device
for a specific PVC within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.3.1.7 |
fecn-frames-pvc-currIdentifies total number of frames for a specific PVC
with FECN set received within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.3.1.8 |
becn-frames-pvc-currIdentifies total number of frames for a specific PVC
with BECN set received within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.3.1.9 |
poll-tx-pvc-currIdentifies total number of probe polls sent to DCE within
current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.3.1.10 |
resp-tx-pvc-currIdentifies total number of probe responses sent to DCE
within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.3.1.11 |
poll-rx-pvc-currIdentifies total number of probe polls received from DCE
on a specific PVC within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.3.1.12 |
resp-rx-pvc-currIdentifies total number of probe responses received from DCE
on a specific PVC within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.3.1.13 |
pvc-loop-currIdentifies whether the specific PVC has been found to be in a loop
back state by link probe's generator process.ro Enumeration .1.3.6.1.4.1.568.8.2.3.1.14 |
ip-poll-tx-pvc-currIdentifies total number of probe IP polls sent to ethernet within
current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.3.1.15 |
ip-resp-tx-pvc-currIdentifies total number of probe IP responses sent to ethernet
within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.3.1.16 |
ip-poll-rx-pvc-currIdentifies total number of probe IP polls received from ethernet
on a specific PVC within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.3.1.17 |
ip-resp-rx-pvc-currIdentifies total number of probe IP responses received from
ethernet on a specific PVC within current 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.3.1.18 |
ipRtrRxLatTxPvcCurrIdentifies total number of Router Receive Latency IP
packets transmitted out the To-Dte port within current
15 minute interval.ro Counter .1.3.6.1.4.1.568.8.2.3.1.19 |
ipRtrRxLatRxPvcCurrIdentifies total number of Router Receive Latency IP
packets received at the Ethernet port within current
15 minute interval.ro Counter .1.3.6.1.4.1.568.8.2.3.1.20 |
ipRtrTxLatTxPvcCurrIdentifies total number of Router Transmit Latency IP
packets transmitted out the Ethernet port within current
15 minute interval.ro Counter .1.3.6.1.4.1.568.8.2.3.1.21 |
ipRtrTxLatRxPvcCurrIdentifies total number of Router Transmit Latency IP
packets received at the To-Dte port within current
15 minute interval.ro Counter .1.3.6.1.4.1.568.8.2.3.1.22 |
pvcStInterval-TablePVC statistic interval table: SEQUENCE OF PVCStInterval-entry .1.3.6.1.4.1.568.8.2.4 |
pvcStInterval-EntryIdentifies an entry (row) in pvc statistic table PVCStInterval-entry .1.3.6.1.4.1.568.8.2.4.1 |
pvc-number-index-intvThe index value which uniquely identifies the PVC
number to which this entry is applicable.ro INTEGER ( 16..991 ) .1.3.6.1.4.1.568.8.2.4.1.1 |
pvcStIntv-indexA number between 1 and 96, where 1 is the most recently
completed 15 minutes interval and 96 is the least recently
completed 15 minutes interval.ro INTEGER ( 1..96 ) .1.3.6.1.4.1.568.8.2.4.1.2 |
dte-frames-pvc-intvIdentifies total frames received from DTE device for a
specific PVC within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.4.1.3 |
dce-frames-pvc-intvIdentifies total frames received from DCE device for a
specific PVC within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.4.1.4 |
dte-octets-pvc-intvIdentifies total octets received from DTE device for a
specific PVC within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.4.1.5 |
dce-octets-pvc-intvIdentifies total octets received from DTE device for a
specific PVC within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.4.1.6 |
dte-frames-with-DE-pvc-intvIdentifies the frames with DE bit set received from DTE device
for a specific PVC within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.4.1.7 |
dce-frames-with-DE-pvc-intvIdentifies the frames with DE bit set received from DCE device
for a specific PVC within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.4.1.8 |
fecn-frames-pvc-intvIdentifies total number of frames for a specific PVC
with FECN set received within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.4.1.9 |
becn-frames-pvc-intvIdentifies total number of frames for a specific PVC
with BECN set received within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.4.1.10 |
poll-tx-pvc-intvIdentifies total number of probe polls sent to DCE within
a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.4.1.11 |
resp-tx-pvc-intvIdentifies total number of probe responses sent to DCE
within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.4.1.12 |
poll-rx-pvc-intvIdentifies total number of probe polls received from DCE
on a specific PVC within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.4.1.13 |
resp-rx-pvc-intvIdentifies total number of probe responses received from
DCE on a specific PVC within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.4.1.14 |
pvc-loop-intvIdentifies whether the specific PVC has been found to be in a loop
back state by link probe's generator process.ro INTEGER .1.3.6.1.4.1.568.8.2.4.1.15 |
ip-poll-tx-pvc-intvIdentifies total number of probe IP polls sent to ethernet within
a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.4.1.16 |
ip-resp-tx-pvc-intvIdentifies total number of probe IP responses sent to ethernet
within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.4.1.17 |
ip-poll-rx-pvc-intvIdentifies total number of probe IP polls received from ethernet
on a specific PVC within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.4.1.18 |
ip-resp-rx-pvc-intvIdentifies total number of probe IP responses received from
ethernet on a specific PVC within a 15 minutes interval.ro Counter .1.3.6.1.4.1.568.8.2.4.1.19 |
ipRtrRxLatTxPvcIntvIdentifies total number of Router Receive Latency IP
packets transmitted out the To-Dte port within a
15 minute interval.ro Counter .1.3.6.1.4.1.568.8.2.4.1.20 |
ipRtrRxLatRxPvcIntvIdentifies total number of Router Receive Latency IP
packets received at the Ethernet port within a
15 minute interval.ro Counter .1.3.6.1.4.1.568.8.2.4.1.21 |
ipRtrTxLatTxPvcIntvIdentifies total number of Router Transmit Latency IP
packets transmitted out the Ethernet port within a
15 minute interval.ro Counter .1.3.6.1.4.1.568.8.2.4.1.22 |
ipRtrTxLatRxPvcIntvIdentifies total number of Router Transmit Latency IP
packets received at the To-Dte port within a
15 minute interval.ro Counter .1.3.6.1.4.1.568.8.2.4.1.23 |
probePerform OBJECT IDENTIFIER .1.3.6.1.4.1.568.8.3 |
chanPerfCurr OBJECT IDENTIFIER .1.3.6.1.4.1.568.8.3.1 |
chan-unvail-toDte-currThis object identifies the channel unavailability due to remote
DTE fault within the latest 15 minutes. This statistical data is
calculated by the channel unavailable time over the full time
interval.ro DisplayString .1.3.6.1.4.1.568.8.3.1.1 |
chan-unavail-toDce-currThis object identifies the channel unavailability due to local
DTE fault within the latest 15 minutes. This statistical data is
calculated by the channel unavailable time over the full time
interval.ro DisplayString .1.3.6.1.4.1.568.8.3.1.2 |
chan-user-load-tx-currchannel average user tx load within the latest 15 minutes,
this statistical data is calculated by user data octets sent
by the channel within the 15 minutes over the total channel
available load ( which depends on physical interface speed).ro DisplayString .1.3.6.1.4.1.568.8.3.1.3 |
chan-user-load-rx-currchannel average user rx load within the latest 15 minutes,
this statistical data is calculated by user data octets received
by the channel within the 15 minutes over the total channel
available load ( which depends on physical interface speed).ro DisplayString .1.3.6.1.4.1.568.8.3.1.4 |
chan-total-load-tx-currchannel total tx load within the latest 15 minutes,
this statistical data is calculated by the total data octets
sent by the channel within the 15 minutes over the channel
available load ( which depends on physical interface speed).ro DisplayString .1.3.6.1.4.1.568.8.3.1.5 |
chan-total-load-rx-currchannel total rx load within the latest 15 minutes,
this statistical data is calculated by total data octets received
by the channel within the 15 minutes over the channel total
available load ( which depends on physical interface speed).ro DisplayString .1.3.6.1.4.1.568.8.3.1.6 |
chanPerfIntv-TableProbe channel performance table, which displays
the performance statistical data based on the probe
channel within previous 24 hours. SEQUENCE OF ChanPerfIntv-Entry .1.3.6.1.4.1.568.8.3.2 |
chanPerfIntv-EntryIdentifies an entry (row) in probe channel performance
table. ChanPerfIntv-Entry .1.3.6.1.4.1.568.8.3.2.1 |
chanPerfIntv-indexIdentifies an entry (row) in historical PVC performance table,
total 96 time intervals, where 1 is the most recently completed
15 minutes interval and 96 is the least recently completed 15
minutes interval (assuming that all 96 intervals are valid).ro INTEGER .1.3.6.1.4.1.568.8.3.2.1.1 |
chan-unavail-toDte-intvThis object identifies the channel unavailability due to remote
DTE fault within a 15 minutes interval. This statistical data is
calculated by the channel unavailable time over the full time
interval.ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.2 |
chan-unavail-toDce-intvThis object identifies the channel unavailability due to local
DTE fault within a 15 minutes interval. This statistical data is
calculated by the channel unavailable time over the full time
interval.ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.3 |
chan-user-load-tx-intvchannel average user tx load within a 15 minutes interval,
this statistical data is calculated by user data octets sent by
the channel within the 15 minutes over the total channel
available load ( which depends on physical interface speed).ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.4 |
chan-user-load-rx-intvchannel average user rx load within a 15 minutes interval,
this statistical data is calculated by user data octets received
by the channel within the 15 minutes over the total channel
available load( which depends on physical interface speed).ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.5 |
chan-total-load-tx-intvchannel total tx load within a 15 minutes interval,
this statistical data is calculated by the total data octets
sent by the channel within the 15 minutes over the total
channel available load ( which depends on physical interface speed).ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.6 |
chan-total-load-rx-intvChannel total rx load within a 15 minutes interval,
this statistical data is calculated by the total data octets
received by the channel within the 15 minutes over the total channel
available load ( which depends on physical interface speed).ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.7 |
chan-min-user-load-tx-intvMinimum chan-user-load-tx within a 15 minutes interval.ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.8 |
chan-min-user-load-tx-time-intvTimestamp of when the minimum chan-user-load-tx
within a 15 minutes interval occurred.ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.9 |
chan-min-user-load-rx-intvMinimum chan-user-load-rx within a 15 minutes interval.ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.10 |
chan-min-user-load-rx-time-intvTimestamp of when the minimum chan-user-load-rx
within a 15 minutes interval occurred.ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.11 |
chan-min-total-load-tx-intvMinimum chan-total-load-tx within a 15 minutes interval.ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.12 |
chan-min-total-load-tx-time-intvTimestamp of when the minimum chan-total-load-tx
within a 15 minutes interval occurred.ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.13 |
chan-min-total-load-rx-intvMinimum chan-total-load-rx within a 15 minutes interval.ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.14 |
chan-min-total-load-rx-time-intvTimestamp of when the minimum chan-total-load-rx
within a 15 minutes interval occurred.ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.15 |
chan-max-user-load-tx-intvMaximum chan-user-load-tx within a 15 minutes interval.ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.16 |
chan-max-user-load-tx-time-intvTimestamp of when the maximum chan-user-load-tx
within a 15 minutes interval occurred.ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.17 |
chan-max-user-load-rx-intvMaximum chan-user-load-rx within a 15 minutes interval.ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.18 |
chan-max-user-load-rx-time-intvTimestamp of when the maximum chan-user-load-rx
within a 15 minutes interval occurred.ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.19 |
chan-max-total-load-tx-intvMaximum chan-total-load-tx within a 15 minutes interval.ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.20 |
chan-max-total-load-tx-time-intvTimestamp of when the maximum chan-total-load-tx
within a 15 minutes interval occurred.ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.21 |
chan-max-total-load-rx-intvMaximum chan-total-load-rx within a 15 minutes interval.ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.22 |
chan-max-total-load-rx-time-intvTimestamp of when the maximum chan-total-load-rx
within a 15 minutes interval occurred.ro DisplayString .1.3.6.1.4.1.568.8.3.2.1.23 |
pvcPerfCurr-TablePVC performance table, which displays
the performance statistical data based on
each PVC. SEQUENCE OF PvcPerfCurr-Entry .1.3.6.1.4.1.568.8.3.3 |
pvcPerfCurr-EntryIdentifies an entry (row) in pvc statistic table PvcPerfCurr-Entry .1.3.6.1.4.1.568.8.3.3.1 |
pvcPerfCurr-num-indexThe index value which uniquely identifies the PVC
number to which this entry is applicable.ro INTEGER ( 16..991 ) .1.3.6.1.4.1.568.8.3.3.1.1 |
pvc-tx-time-currProbe token average round trip time within the latest
15 minutes for a specific PVC. A -1 value indicates
data is Not-Avail.ro INTEGER .1.3.6.1.4.1.568.8.3.3.1.2 |
pvc-unavail-toDteThis object identifies the PVC average unavailability
within the latest 15 minutes. This statistical data is
calculated by a PVC unavailable time due to the network
or remote DTE fault over the full time interval.ro DisplayString .1.3.6.1.4.1.568.8.3.3.1.3 |
pvc-unavail-toDceThis object identifies the PVC average unavailability
within the latest 15 minutes. This statistical data is
calculated by a PVC unavailable time due to the local
DTE fault over the full time interval.ro DisplayString .1.3.6.1.4.1.568.8.3.3.1.4 |
pvc-user-load-tx-currThis object identifies the PVC average user tx load within the
latest 15 minutes. This statistical data is calculated by
user data octets sent by a specific PVC within the 15 minutes
over the PVC total available load.
Note: If the CIR is correctly defined for this PVC, PVC available
load will depend on CIR, otherwise, it will get it from
interface speed.ro DisplayString .1.3.6.1.4.1.568.8.3.3.1.5 |
pvc-user-load-rx-currThis object identifies the PVC average user rx load within the
latest 15 minutes. This statistical data is calculated by
user data octets received by a specific PVC within the 15 minutes
over the PVC total available load.
Note: If the CIR is correctly defined for this PVC, PVC available
load will depend on CIR, otherwise, it will get it from
interface speed.ro DisplayString .1.3.6.1.4.1.568.8.3.3.1.6 |
pvc-total-load-tx-currThis object identifies the PVC total tx load within the
latest 15 minutes. This statistical data is calculated by
total data octets sent by a specific PVC within the 15 minutes
over the PVC total available load.
Note: If the CIR is correctly defined for this PVC, PVC available
load will depend on CIR, otherwise, it will get it from
interface speed.ro DisplayString .1.3.6.1.4.1.568.8.3.3.1.7 |
pvc-total-load-rx-currThis object identifies the PVC total rx load within the
latest 15 minutes. This statistical data is calculated by
total data octets received by a specific PVC within the 15 minutes
over the PVC total available load.
Note: If the CIR is correctly defined for this PVC, PVC available
load will depend on CIR, otherwise, it will get it from
interface speed.ro DisplayString .1.3.6.1.4.1.568.8.3.3.1.8 |
pvc-CIR-toNet-exceed-currThis object identifies the number of exceeding CIR times that the
network detected within the current interval. The measurement is
done for every Tc, and the direction is to the network.ro INTEGER .1.3.6.1.4.1.568.8.3.3.1.9 |
pvc-EIR-toNet-exceed-currThis object identifies the number of exceeding EIR times that the
network detected within the current interval. The measurement is
done for every Tc, and the direction is to the network.ro INTEGER .1.3.6.1.4.1.568.8.3.3.1.10 |
pvc-loss-frame-tx-currThis object identifies the percentage of tx loss of frames within
the total tx frames for this PVC. A -1 value indicates
data is Not-Avail.ro INTEGER .1.3.6.1.4.1.568.8.3.3.1.11 |
pvc-loss-frame-rx-currThis object identifies the percentage of rx loss of frames within
the total rx frames for this PVC. A -1 value indicates
data is Not-Avail.ro INTEGER .1.3.6.1.4.1.568.8.3.3.1.12 |
pvc-ip-tx-time-currProbe token average round trip time via ethernet and using UDP/IP
packets within the latest 15 minutes for a specific PVC.
A -1 value indicates data is Not-Avail.ro INTEGER .1.3.6.1.4.1.568.8.3.3.1.13 |
pvcIpRtrRxLatTxTimeCurrRouter Receive Latency IP Packet average round trip time
from first byte transmitted out the To-Dte port, to the
last byte received on the Ethernet port,
within the latest 15 minutes for a specific PVC.
A -1 value indicates data is Not-Avail.ro INTEGER .1.3.6.1.4.1.568.8.3.3.1.14 |
pvcIpRtrTxLatTxTimeCurrRouter Transmit Latency IP Packet average round trip time
from first byte transmitted out the Ethernet port, to the
last byte received on the To-Dte port,
within the latest 15 minutes for a specific PVC.
A -1 value indicates data is Not-Avail.ro INTEGER .1.3.6.1.4.1.568.8.3.3.1.15 |
pvcPerfIntv-TablePVC performance interval table, which displays
the performance statistical data based on each
PVC in previous 24 hours. SEQUENCE OF PvcPerfIntv-Entry .1.3.6.1.4.1.568.8.3.4 |
pvcPerfIntv-EntryIdentifies an entry (row) in pvc statistic table PvcPerfIntv-Entry .1.3.6.1.4.1.568.8.3.4.1 |
pvcPerfIntv-num-indexThe index value which uniquely identifies the PVC
number to which this entry is applicable.ro INTEGER ( 16..991 ) .1.3.6.1.4.1.568.8.3.4.1.1 |
pvcPerf-intv-indexIdentifies an entry (row) in PVC performance table, with
total 96 time intervals, where 1 is the most recently completed
15 minutes interval and 96 is the least recently completed 15
minutes interval (assuming that all 96 intervals are valid).ro INTEGER .1.3.6.1.4.1.568.8.3.4.1.2 |
pvc-tx-time-intvProbe token average round trip time within a
15 minutes interval for a specific PVC. A -1 value indicates
data is Not-Avail.ro INTEGER .1.3.6.1.4.1.568.8.3.4.1.3 |
pvc-unavail-toDte-intvThis object identifies the PVC average unavailability
within a 15 minutes interval. This statistical data is
calculated by a PVC unavailable time due to the network
or remote DTE fault over the full time interval.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.4 |
pvc-unavail-toDce-intvThis object identifies the PVC average unavailability
within a 15 minutes interval. This statistical data is
calculated by a PVC unavailable time due to the local DTE
fault over the full time interval.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.5 |
pvc-user-load-tx-intvThis object identifies the PVC average user tx load within
a 15 minutes interval. This statistical data is calculated by
user data octets sent by a specific PVC within the 15 minutes
over the PVC total available load.
Note: If the CIR is correctly defined for this PVC, PVC available
load will depend on CIR, otherwise, it will get it from
interface speed.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.6 |
pvc-user-load-rx-intvThis object identifies the PVC average user rx load within
a 15 minutes interval. This statistical data is calculated by
user data octets received by a specific PVC within the 15 minutes
over the PVC total available load.
Note: If the CIR is correctly defined for this PVC, PVC available
load will depend on CIR, otherwise, it will get it from
interface speed.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.7 |
pvc-total-load-tx-intvThis object identifies the PVC total tx load within
a 15 minutes interval. This statistical data is calculated by
total data octets sent by a specific PVC within the 15 minutes
over the PVC total available load.
Note: If the CIR is correctly defined for this PVC, PVC available
load will depend on CIR, otherwise, it will get it from
interface speed.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.8 |
pvc-total-load-rx-intvThis object identifies the PVC total rx load within
a 15 minutes interval. This statistical data is calculated by
total data octets received by a specific PVC within the 15 minutes
over the PVC total available load.
Note: If the CIR is correctly defined for this PVC, PVC available
load will depend on CIR, otherwise, it will get it from
interface speed.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.9 |
pvc-CIR-toNet-exceed-intvThis object identifies the number of exceeding CIR times that the
network detected within an interval. The measurement is
done for every Tc, and the direction is to the network.ro INTEGER .1.3.6.1.4.1.568.8.3.4.1.10 |
pvc-EIR-toNet-exceed-intvThis object identifies the number of exceeding EIR times that the
network detected within an interval. The measurement is
done for every Tc, and the direction is to the network.ro INTEGER .1.3.6.1.4.1.568.8.3.4.1.11 |
pvc-loss-frame-tx-intvThis object identifies the percentage of tx loss of frames within
the total tx frames for this PVC in this interval.ro Enumeration .1.3.6.1.4.1.568.8.3.4.1.12 |
pvc-loss-frame-rx-intvThis object identifies the percentage of rx loss of frames within
the total rx frames for this PVC in this interval.ro Enumeration .1.3.6.1.4.1.568.8.3.4.1.13 |
pvc-ip-tx-time-intvProbe token average round trip time via ethernet and using UDP/IP
packets within a 15 minutes interval for a specific PVC.
A -1 value indicates data is Not-Avail.ro INTEGER .1.3.6.1.4.1.568.8.3.4.1.14 |
pvcIpRtrRxLatTxTimeIntvRouter Receive Latency IP Packet average round trip time
from first byte transmitted out the To-Dte port, to the
last byte received on the Ethernet port,
within a 15 minute interval for a specific PVC.
A -1 value indicates data is Not-Avail.ro INTEGER .1.3.6.1.4.1.568.8.3.4.1.15 |
pvcIpRtrTxLatTxTimeIntvRouter Transmit Latency IP Packet average round trip time
from first byte transmitted out the Ethernet port, to the
last byte received on the To-Dte port,
within a 15 minute interval for a specific PVC.
A -1 value indicates data is Not-Avail.ro INTEGER .1.3.6.1.4.1.568.8.3.4.1.16 |
pvc-min-tx-time-intvMinimum pvc-tx-time within a 15 minutes interval for a specific PVC.ro INTEGER .1.3.6.1.4.1.568.8.3.4.1.17 |
pvc-min-tx-time-time-intvTimestamp of when the minimum pvc-tx-time
within a 15 minutes interval occurred.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.18 |
pvc-min-user-load-tx-intvMinimum pvc-user-load-tx within a 15 minutes interval.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.19 |
pvc-min-user-load-tx-time-intvTimestamp of when the minimum pvc-user-load-tx
within a 15 minutes interval occurred.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.20 |
pvc-min-user-load-rx-intvMinimum pvc-user-load-rx within a 15 minutes interval.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.21 |
pvc-min-user-load-rx-time-intvTimestamp of when the minimum pvc-user-load-rx
within a 15 minutes interval occurred.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.22 |
pvc-min-total-load-tx-intvMinimum pvc-total-load-tx within a 15 minutes interval.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.23 |
pvc-min-total-load-tx-time-intvTimestamp of when the minimum pvc-total-load-tx
within a 15 minutes interval occurred.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.24 |
pvc-min-total-load-rx-intvMinimum pvc-total-load-rx within a 15 minutes interval.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.25 |
pvc-min-total-load-rx-time-intvTimestamp of when the minimum pvc-total-load-rx
within a 15 minutes interval occurred.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.26 |
pvc-min-ip-tx-time-intvMinimum pvc-ip-tx-time within a 15 minutes interval.ro INTEGER .1.3.6.1.4.1.568.8.3.4.1.27 |
pvc-min-ip-tx-time-time-intvTimestamp of when the minimum pvc-ip-tx-time
within a 15 minutes interval occurred.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.28 |
pvc-max-tx-time-intvMaximum pvc-tx-time within a 15 minutes interval.ro INTEGER .1.3.6.1.4.1.568.8.3.4.1.29 |
pvc-max-tx-time-time-intvTimestamp of when the maximum pvc-tx-time
within a 15 minutes interval occurred.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.30 |
pvc-max-user-load-tx-intvMaximum pvc-user-load-tx within a 15 minutes interval.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.31 |
pvc-max-user-load-tx-time-intvTimestamp of when the maximum pvc-user-load-tx
within a 15 minutes interval occurred.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.32 |
pvc-max-user-load-rx-intvMaximum pvc-user-load-rx within a 15 minutes interval.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.33 |
pvc-max-user-load-rx-time-intvTimestamp of when the maximum pvc-user-load-rx
within a 15 minutes interval occurred.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.34 |
pvc-max-total-load-tx-intvMaximum pvc-total-load-tx within a 15 minutes interval.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.35 |
pvc-max-total-load-tx-time-intvTimestamp of when the maximum pvc-total-load-tx
within a 15 minutes interval occurred.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.36 |
pvc-max-total-load-rx-intvMaximum pvc-total-load-rx within a 15 minutes interval.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.37 |
pvc-max-total-load-rx-time-intvTimestamp of when the maximum pvc-total-load-rx
within a 15 minutes interval occurred.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.38 |
pvc-max-ip-tx-time-intvMaximum pvc-ip-tx-time within a 15 minutes interval.ro INTEGER .1.3.6.1.4.1.568.8.3.4.1.39 |
pvc-max-ip-tx-time-time-intvTimestamp of when the maximum pvc-ip-tx-time
within a 15 minutes interval occurred.ro DisplayString .1.3.6.1.4.1.568.8.3.4.1.40 |
probeTrafficShape OBJECT IDENTIFIER .1.3.6.1.4.1.568.8.4 |
pvcShapeThresh OBJECT IDENTIFIER .1.3.6.1.4.1.568.8.4.1 |
pvcShapeThreshLevel-1This parameter defines the maximum percentage of PVC traffic
(measured in TC) within this PVC CIR in shape level 1 (currently
is 10%).ro INTEGER .1.3.6.1.4.1.568.8.4.1.1 |
pvcShapeThreshLevel-2This parameter defines the maximum percentage of PVC traffic
(measured in TC) within this PVC CIR in shape level 2 (currently
is 25%).ro INTEGER .1.3.6.1.4.1.568.8.4.1.2 |
pvcShapeThreshLevel-3This parameter defines the maximum percentage of PVC traffic
(measured in TC) within this PVC CIR in shape level 3 (currently
is 45%).ro INTEGER .1.3.6.1.4.1.568.8.4.1.3 |
pvcShapeThreshLevel-4This parameter defines the maximum percentage of PVC traffic
(measured in TC) within this PVC CIR in shape level 4 (currently
is 75%).ro INTEGER .1.3.6.1.4.1.568.8.4.1.4 |
pvcShapeThreshLevel-5This parameter defines the maximum percentage of PVC traffic
(measured in TC) within this PVC CIR in shape level 5 (currently
is 90%).ro INTEGER .1.3.6.1.4.1.568.8.4.1.5 |
pvcShapeThreshLevel-6This parameter defines the maximum percentage of PVC traffic
(measured in TC) within this PVC CIR in shape level 6 (currently
is 100%).ro INTEGER .1.3.6.1.4.1.568.8.4.1.6 |
pvcShapeThreshLevel-7This parameter defines the maximum percentage of PVC traffic
(measured in TC) within this PVC CIR in shape level 7 (currently
is more than 100%).ro INTEGER .1.3.6.1.4.1.568.8.4.1.7 |
pvcShapeCurrToDce-TablePVC current traffic shape to DCE table, which displays
the traffic shape information based on each PVC. SEQUENCE OF PvcShapeCurrToDce-Entry .1.3.6.1.4.1.568.8.4.2 |
pvcShapeCurrToDce-EntryIdentifies an entry (row) in pvc current traffic shape to DCE table PvcShapeCurrToDce-Entry .1.3.6.1.4.1.568.8.4.2.1 |
pvcShapeCurrToDce-indexThe index value which uniquely identifies the PVC
number to which this entry is applicable.ro INTEGER ( 16..991 ) .1.3.6.1.4.1.568.8.4.2.1.1 |
pvcShapeCurrToDceLevel-1This object identifies the percentage of traffic in level one
in current 15 minutes to the direction of DCE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.2.1.2 |
pvcShapeCurrToDceLevel-2This object identifies the percentage of traffic in level two
in current 15 minutes to the direction of DCE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.2.1.3 |
pvcShapeCurrToDceLevel-3This object identifies the percentage of traffic in level three
in current 15 minutes to the direction of DCE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.2.1.4 |
pvcShapeCurrToDceLevel-4This object identifies the percentage of traffic in level four
in current 15 minutes to the direction of DCE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.2.1.5 |
pvcShapeCurrToDceLevel-5This object identifies the percentage of traffic in level five
in current 15 minutes to the direction of DCE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.2.1.6 |
pvcShapeCurrToDceLevel-6This object identifies the percentage of traffic in level six
in current 15 minutes to the direction of DCE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.2.1.7 |
pvcShapeCurrToDceLevel-7This object identifies the percentage of traffic in level seven
in current 15 minutes to the direction of DCE.ro INTEGER (0..100 ) .1.3.6.1.4.1.568.8.4.2.1.8 |
pvcShapeCurrToDte-TablePVC current traffic shape table, which displays
the traffic shape information based on each PVC. SEQUENCE OF PvcShapeCurrToDte-Entry .1.3.6.1.4.1.568.8.4.3 |
pvcShapeCurrToDte-EntryIdentifies an entry (row) in pvc current traffic shape to DTE table PvcShapeCurrToDte-Entry .1.3.6.1.4.1.568.8.4.3.1 |
pvcShapeCurrToDte-indexThe index value which uniquely identifies the PVC
number to which this entry is applicable.ro INTEGER ( 16..991 ) .1.3.6.1.4.1.568.8.4.3.1.1 |
pvcShapeCurrToDteLevel-1This object identifies the percentage of traffic in level one
in current 15 minutes to the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.3.1.2 |
pvcShapeCurrToDteLevel-2This object identifies the percentage of traffic in level two
in current 15 minutes to the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.3.1.3 |
pvcShapeCurrToDteLevel-3This object identifies the percentage of traffic in level three
in current 15 minutes to the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.3.1.4 |
pvcShapeCurrToDteLevel-4This object identifies the percentage of traffic in level four
in current 15 minutes to the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.3.1.5 |
pvcShapeCurrToDteLevel-5This object identifies the percentage of traffic in level five
in current 15 minutes to the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.3.1.6 |
pvcShapeCurrToDteLevel-6This object identifies the percentage of traffic in level six
in current 15 minutes to the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.3.1.7 |
pvcShapeCurrToDteLevel-7This object identifies the percentage of traffic in level seven
in current 15 minutes to the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.3.1.8 |
pvcShapeIntvToDce-TablePVC shape to DCE interval table, which displays the pvc traffic shape
information to the direction of DCE within 24 hours. SEQUENCE OF PvcShapeIntvToDce-Entry .1.3.6.1.4.1.568.8.4.4 |
pvcShapeIntvToDce-EntryIdentifies an entry (row) in pvc traffic shape to DCE interval table PvcShapeIntvToDce-Entry .1.3.6.1.4.1.568.8.4.4.1 |
pvcShapeIntvToDce-pvcIxThe index value which uniquely identifies the PVC
number to which this entry is applicable.ro INTEGER ( 16..991 ) .1.3.6.1.4.1.568.8.4.4.1.1 |
pvcShapeIntvToDce-intvIxThe index value which uniquely identifies the interval
number to which this entry is applicable.ro INTEGER ( 1..96 ) .1.3.6.1.4.1.568.8.4.4.1.2 |
pvcShapeIntvToDceLevel-1This object identifies the percentage of traffic in level one
within a specific 15-minutes interval in the direction of DCE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.4.1.3 |
pvcShapeIntvToDceLevel-2This object identifies the percentage of traffic in level two
within a specific 15-minutes interval in the direction of DCE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.4.1.4 |
pvcShapeIntvToDceLevel-3This object identifies the percentage of traffic in level three
within a specific 15-minutes interval in the direction of DCE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.4.1.5 |
pvcShapeIntvToDceLevel-4This object identifies the percentage of traffic in level four
within a specific 15-minutes interval in the direction of DCE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.4.1.6 |
pvcShapeIntvToDceLevel-5This object identifies the percentage of traffic in level five
within a specific 15-minutes interval in the direction of DCE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.4.1.7 |
pvcShapeIntvToDceLevel-6This object identifies the percentage of traffic in level six
within a specific 15-minutes interval in the direction of DCE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.4.1.8 |
pvcShapeIntvToDceLevel-7This object identifies the percentage of traffic in level seven
within a specific 15-minutes interval in the direction of DCE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.4.1.9 |
pvcShapeIntvToDte-TablePVC shape to DTE interval table, which displays the pvc traffic
information to the direction of DTE within 24 hours. SEQUENCE OF PvcShapeIntvToDte-Entry .1.3.6.1.4.1.568.8.4.5 |
pvcShapeIntvToDte-EntryIdentifies an entry (row) in pvc traffic shape to DTE interval table PvcShapeIntvToDte-Entry .1.3.6.1.4.1.568.8.4.5.1 |
pvcShapeIntvToDte-pvcIxThe index value which uniquely identifies the PVC
number to which this entry is applicable.ro INTEGER ( 16..991 ) .1.3.6.1.4.1.568.8.4.5.1.1 |
pvcShapeIntvToDte-intvIxThe index value which uniquely identifies the interval
number to which this entry is applicable.ro INTEGER ( 1..96 ) .1.3.6.1.4.1.568.8.4.5.1.2 |
pvcShapeIntvToDteLevel-1This object identifies the percentage of traffic in level one
within a specific 15-minutes interval in the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.5.1.3 |
pvcShapeIntvToDteLevel-2This object identifies the percentage of traffic in level two
within a specific 15-minutes interval in the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.5.1.4 |
pvcShapeIntvToDteLevel-3This object identifies the percentage of traffic in level three
within a specific 15-minutes interval in the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.5.1.5 |
pvcShapeIntvToDteLevel-4This object identifies the percentage of traffic in level four
within a specific 15-minutes interval in the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.5.1.6 |
pvcShapeIntvToDteLevel-5This object identifies the percentage of traffic in level five
within a specific 15-minutes interval in the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.5.1.7 |
pvcShapeIntvToDteLevel-6This object identifies the percentage of traffic in level six
within a specific 15-minutes interval in the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.5.1.8 |
pvcShapeIntvToDteLevel-7This object identifies the percentage of traffic in level seven
within a specific 15-minutes interval in the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.4.5.1.9 |
probeHistorical OBJECT IDENTIFIER .1.3.6.1.4.1.568.8.5 |
histIntvStartTimeIntv-TableProbe historical interval start time table, which displays
the interval starting time for each interval covering
an historical 3 hours. SEQUENCE OF HistIntvStartTimeIntv-Entry .1.3.6.1.4.1.568.8.5.1 |
histIntvStartTimeIntv-EntryIdentifies an entry (row) in probe interval start time
interval table. HistIntvStartTimeIntv-Entry .1.3.6.1.4.1.568.8.5.1.1 |
histIntvStartTimeIntv-indexIdentifies an entry (row) in historical PVC performance table,
total 12 time intervals, where 1 is the most recently completed
15 minutes interval and 12 is the least recently completed 15
minutes interval (assuming that all 12 intervals are valid).ro INTEGER .1.3.6.1.4.1.568.8.5.1.1.1 |
hist-intv-start-timehist-intv-start-time displays the current interval starting
time with 4 digits year, 2 digits month, 2 digits date and
hours, minutes and seconds, which are each 2 digits.ro DisplayString .1.3.6.1.4.1.568.8.5.1.1.2 |
histChanPerfIntv-TableProbe channel performance table, which displays
the performance statistical data based on the probe
channel covering an historical 3 hours. SEQUENCE OF HistChanPerfIntv-Entry .1.3.6.1.4.1.568.8.5.2 |
histChanPerfIntv-EntryIdentifies an entry (row) in probe historical channel
performance table. HistChanPerfIntv-Entry .1.3.6.1.4.1.568.8.5.2.1 |
histChanPerfIntv-indexIdentifies an entry (row) in historical PVC performance table,
total 12 time intervals, where 1 is the most recently completed
15 minutes interval and 12 is the least recently completed 15
minutes interval (assuming that all 12 intervals are valid).ro INTEGER .1.3.6.1.4.1.568.8.5.2.1.1 |
hist-chan-unavail-toDte-intvThis object identifies the channel unavailability due to remote
DTE fault within a 15 minute interval. This statistical data is
calculated by the channel unavailable time over the full time
interval.ro DisplayString .1.3.6.1.4.1.568.8.5.2.1.2 |
hist-chan-unavail-toDce-intvThis object identifies the channel unavailability due to local
DTE fault within a 15 minutes interval. This statistical data is
calculated by the channel unavailable time over the full time
interval.ro DisplayString .1.3.6.1.4.1.568.8.5.2.1.3 |
hist-chan-user-load-tx-intvchannel average user tx load within a 15 minute interval,
this statistical data is calculated by user data octets sent by
the channel within the 15 minutes over the total channel
available load ( which depends on physical interface speed).ro DisplayString .1.3.6.1.4.1.568.8.5.2.1.4 |
hist-chan-user-load-rx-intvchannel average user rx load within a 15 minute interval,
this statistical data is calculated by user data octets received
by the channel within the 15 minutes over the total channel
available load( which depends on physical interface speed).ro DisplayString .1.3.6.1.4.1.568.8.5.2.1.5 |
histPvcPerfIntv-TablePVC performance interval table, which displays
the performance statistical data based on each
PVC in an historical 3 hours. SEQUENCE OF HistPvcPerfIntv-Entry .1.3.6.1.4.1.568.8.5.3 |
histPvcPerfIntv-EntryIdentifies an entry (row) in pvc statistic table HistPvcPerfIntv-Entry .1.3.6.1.4.1.568.8.5.3.1 |
histPvcPerfIntv-num-indexThe index value which uniquely identifies the PVC
number to which this entry is applicable.ro INTEGER ( 16..991 ) .1.3.6.1.4.1.568.8.5.3.1.1 |
histPvcPerf-intv-indexIdentifies an entry (row) in historical PVC performance table,
total 12 time intervals, where 1 is the most recently completed
15 minutes interval and 12 is the least recently completed 15
minutes interval (assuming that all 12 intervals are valid).ro INTEGER .1.3.6.1.4.1.568.8.5.3.1.2 |
hist-pvc-tx-time-intvProbe token average round trip time within a
15 minutes interval for a specific PVC. A -1 value indicates
data is Not-Avail.ro INTEGER .1.3.6.1.4.1.568.8.5.3.1.3 |
hist-pvc-unavail-toDte-intvThis object identifies the PVC average unavailability
within a 15 minutes interval. This statistical data is
calculated by a PVC unavailable time due to the network
or remote DTE fault over the full time interval.ro DisplayString .1.3.6.1.4.1.568.8.5.3.1.4 |
hist-pvc-unavail-toDce-intvThis object identifies the PVC average unavailability
within a 15 minutes interval. This statistical data is
calculated by a PVC unavailable time due to the local DTE
fault over the full time interval.ro DisplayString .1.3.6.1.4.1.568.8.5.3.1.5 |
hist-pvc-user-load-tx-intvThis object identifies the PVC average user tx load within
a 15 minutes interval. This statistical data is calculated by
user data octets sent by a specific PVC within the 15 minutes
over the PVC total available load.
Note: If the CIR is correctly defined for this PVC, PVC available
load will depend on CIR, otherwise, it will get it from
interface speed.ro DisplayString .1.3.6.1.4.1.568.8.5.3.1.6 |
hist-pvc-user-load-rx-intvThis object identifies the PVC average user rx load within
a 15 minutes interval. This statistical data is calculated by
user data octets received by a specific PVC within the 15 minutes
over the PVC total available load.
Note: If the CIR is correctly defined for this PVC, PVC available
load will depend on CIR, otherwise, it will get it from
interface speed.ro DisplayString .1.3.6.1.4.1.568.8.5.3.1.7 |
hist-pvc-CIR-toNet-exceed-intvThis object identifies the number of exceeding CIR times that the
network detected within an interval. The measurement is
done for every Tc, and the direction is to the network.ro INTEGER .1.3.6.1.4.1.568.8.5.3.1.8 |
hist-pvc-loss-frame-tx-intvThis object identifies the percentage of tx loss of frames within
the total tx frames for this PVC in this interval.ro Enumeration .1.3.6.1.4.1.568.8.5.3.1.9 |
hist-pvc-loss-frame-rx-intvThis object identifies the percentage of rx loss of frames within
the total rx frames for this PVC in this interval.ro Enumeration .1.3.6.1.4.1.568.8.5.3.1.10 |
histPvcShapeIntvToDce-TablePVC shape to DCE interval table, which displays the pvc traffic shape
information to the direction of DCE over 3 previous hours. SEQUENCE OF HistPvcShapeIntvToDce-Entry .1.3.6.1.4.1.568.8.5.4 |
histPvcShapeIntvToDce-EntryIdentifies an entry (row) in pvc traffic shape to DCE interval table HistPvcShapeIntvToDce-Entry .1.3.6.1.4.1.568.8.5.4.1 |
histPvcShapeIntvToDce-pvcIxThe index value which uniquely identifies the PVC
number to which this entry is applicable.ro INTEGER ( 16..991 ) .1.3.6.1.4.1.568.8.5.4.1.1 |
histPvcShapeIntvToDce-intvIxThe index value which uniquely identifies the interval
number to which this entry is applicable.ro INTEGER ( 1..12 ) .1.3.6.1.4.1.568.8.5.4.1.2 |
histPvcShapeIntvToDceLevel-1This object identifies the percentage of traffic in level one
within a specific 15-minutes interval in the direction of DCE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.5.4.1.3 |
histPvcShapeIntvToDceLevel-2This object identifies the percentage of traffic in level two
within a specific 15-minutes interval in the direction of DCE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.5.4.1.4 |
histPvcShapeIntvToDceLevel-3This object identifies the percentage of traffic in level three
within a specific 15-minutes interval in the direction of DCE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.5.4.1.5 |
histPvcShapeIntvToDceLevel-4This object identifies the percentage of traffic in level four
within a specific 15-minutes interval in the direction of DCE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.5.4.1.6 |
histPvcShapeIntvToDceLevel-5This object identifies the percentage of traffic in level five
within a specific 15-minutes interval in the direction of DCE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.5.4.1.7 |
histPvcShapeIntvToDceLevel-6This object identifies the percentage of traffic in level six
within a specific 15-minutes interval in the direction of DCE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.5.4.1.8 |
histPvcShapeIntvToDceLevel-7This object identifies the percentage of traffic in level seven
within a specific 15-minutes interval in the direction of DCE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.5.4.1.9 |
histPvcShapeIntvToDte-TablePVC shape to DTE interval table, which displays the pvc traffic
information to the direction of DTE over 3 previous hours. SEQUENCE OF HistPvcShapeIntvToDte-Entry .1.3.6.1.4.1.568.8.5.5 |
histPvcShapeIntvToDte-EntryIdentifies an entry (row) in pvc traffic shape to DTE interval table HistPvcShapeIntvToDte-Entry .1.3.6.1.4.1.568.8.5.5.1 |
histPvcShapeIntvToDte-pvcIxThe index value which uniquely identifies the PVC
number to which this entry is applicable.ro INTEGER ( 16..991 ) .1.3.6.1.4.1.568.8.5.5.1.1 |
histPvcShapeIntvToDte-intvIxThe index value which uniquely identifies the interval
number to which this entry is applicable.ro INTEGER ( 1..12 ) .1.3.6.1.4.1.568.8.5.5.1.2 |
histPvcShapeIntvToDteLevel-1This object identifies the percentage of traffic in level one
within a specific 15-minutes interval in the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.5.5.1.3 |
histPvcShapeIntvToDteLevel-2This object identifies the percentage of traffic in level two
within a specific 15-minutes interval in the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.5.5.1.4 |
histPvcShapeIntvToDteLevel-3This object identifies the percentage of traffic in level three
within a specific 15-minutes interval in the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.5.5.1.5 |
histPvcShapeIntvToDteLevel-4This object identifies the percentage of traffic in level four
within a specific 15-minutes interval in the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.5.5.1.6 |
histPvcShapeIntvToDteLevel-5This object identifies the percentage of traffic in level five
within a specific 15-minutes interval in the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.5.5.1.7 |
histPvcShapeIntvToDteLevel-6This object identifies the percentage of traffic in level six
within a specific 15-minutes interval in the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.5.5.1.8 |
histPvcShapeIntvToDteLevel-7This object identifies the percentage of traffic in level seven
within a specific 15-minutes interval in the direction of DTE.ro INTEGER ( 0..100 ) .1.3.6.1.4.1.568.8.5.5.1.9 |
probeIntervalStartTime OBJECT IDENTIFIER .1.3.6.1.4.1.568.8.6 |
intvStartTimeIntv-TableProbe interval start time table, which displays
the interval starting time for each interval covering
the last 24 hours. SEQUENCE OF IntvStartTimeIntv-Entry .1.3.6.1.4.1.568.8.6.1 |
intvStartTimeIntv-EntryIdentifies an entry (row) in probe interval start time
interval table. IntvStartTimeIntv-Entry .1.3.6.1.4.1.568.8.6.1.1 |
intvStartTimeIntv-indexIdentifies an entry (row) in interval start time table,
total 96 time intervals, where 1 is the most recently completed
15 minutes interval and 96 is the least recently completed 15
minutes interval.ro INTEGER .1.3.6.1.4.1.568.8.6.1.1.1 |
intv-start-timeintv-start-time displays the current interval starting
time with 4 digits year, 2 digits month, 2 digits date and
hours, minutes and seconds, which are each 2 digits.ro DisplayString .1.3.6.1.4.1.568.8.6.1.1.2 |
dbuConfigGroup OBJECT IDENTIFIER .1.3.6.1.4.1.568.8.7 |
dbuPVCTableDBU PVC table. It contains PVC/DLCI Dial-Backup information SEQUENCE OF DbuPVCEntry .1.3.6.1.4.1.568.8.7.1 |
dbuPVCEntryIdentifies an entry (row) in dbuPVCTable. DbuPVCEntry .1.3.6.1.4.1.568.8.7.1.1 |
dbuPVCTableIndexIdentifies an entry (row) in PVC table as the local
PVC (DLCI) Number.ro INTEGER ( 16..991 ) .1.3.6.1.4.1.568.8.7.1.1.1 |
dbuRemotePVCDlciDefines the remote PVC's DLCI number the data is to be routed to.rw INTEGER .1.3.6.1.4.1.568.8.7.1.1.2 |
dbuIsdnAddressDefines the ISDN Dialing Address to reach the PVC's backup siterw DisplayString .1.3.6.1.4.1.568.8.7.1.1.3 |
dbuPvcCirThis parameter defines the maximum transfer information rate
(Bits Per Second) toward the backup PVC.rw INTEGER .1.3.6.1.4.1.568.8.7.1.1.4 |
dbuMasterSlaveDefines whether the DBU probe is a Master or Slave.rw Enumeration .1.3.6.1.4.1.568.8.7.2 |
dbuBackupTypeDefines the type of backup.rw Enumeration .1.3.6.1.4.1.568.8.7.3 |
dbuPVCAddThis object allows the user to add a PVC to the existing PVC
table, the added PVC must not exist before it is added.rw INTEGER ( 16..991 ) .1.3.6.1.4.1.568.8.7.4 |
dbuPVCDeleteThis object allows the user to delete a PVC from the existing PVC
table, the PVC must exist before it is deleted.rw INTEGER ( 16..991 ) .1.3.6.1.4.1.568.8.7.5 |
dbuRecoverCountNumber of LMI Active Occurrences to restore PVC
change request. The value is between 1 to 20.rw INTEGER ( 0..10 ) .1.3.6.1.4.1.568.8.7.6 |
dbuDialedIsdnAddressDefines the Dialed ISDN Address for the most recent DBU callro DisplayString .1.3.6.1.4.1.568.8.7.7 |
deviceStatusGroup OBJECT IDENTIFIER .1.3.6.1.4.1.568.8.8 |
globalStatusDefines device status as:
ready = Device is operating normally.
connected = At least one PVC is in backup mode.
test = Device is in test mode (Not implemented yet).
hwFailure = ISDN line is not operable due to a
hardware failure.ro Enumeration .1.3.6.1.4.1.568.8.8.1 |
pvcStatusTablePer PVC status table. The PVCs(DLCIs) monitored are
PVCs(DLCIs) defined by LMI messages from the network. SEQUENCE OF PvcStatusEntry .1.3.6.1.4.1.568.8.8.2 |
pvcStatusEntryIdentifies an entry (row) in pvcStatusTable. PvcStatusEntry .1.3.6.1.4.1.568.8.8.2.1 |
pvcStatusIndexIdentifies an entry (row) in pvcStatusTable as the local
PVC (DLCI) Number.ro INTEGER ( 16..991 ) .1.3.6.1.4.1.568.8.8.2.1.1 |
pvcStatusDefines the PVC Status as:
pvcInactive = Configured at the network, but not active.
pvcActive = Configured at the network, and active.
pvcConnected = Pvc connected in backup mode.
pvcTest = Pvc in test mode (Not yet implemented).ro Enumeration .1.3.6.1.4.1.568.8.8.2.1.2 |
eventSubjectDefines CP-3000 Log Events as:
device = Device specific events.
pvc = PVC specific events.ro Enumeration .1.3.6.1.4.1.568.8.8.3 |
pvcIdentifierIdentifies the PVC Number for PVC specific events only.
This objects has no meaning for Device specific events.ro INTEGER ( 16..991 ) .1.3.6.1.4.1.568.8.8.4 |
cp3000LogCodeCP-3000 ASCII Log Code for Device or PVC eventsro DisplayString .1.3.6.1.4.1.568.8.8.5 |
cp3000LogSpeedCP-3000 ASCII Log Code for ISDN Line Speedro DisplayString .1.3.6.1.4.1.568.8.8.6 |
cp3000LogDateDate and Time in ASCII format: YYMMDDhhmmssro DisplayString .1.3.6.1.4.1.568.8.8.7 |
cp3000LogInfoNeed to ask what goes in herero DisplayString .1.3.6.1.4.1.568.8.8.8 |
trapAcknowledgeGroup OBJECT IDENTIFIER .1.3.6.1.4.1.568.8.9 |
trapAckEnableAcknowledgement setting for CP-3000 Log Event Traps:
enabled = NMS has to acknowledge traps received.
disabled = NMS doesn't need to acknowledge traps received.rw Enumeration .1.3.6.1.4.1.568.8.9.1 |
trapAckTimeoutTimeout value to retransmit a trap when trapAckEnable
object == enabled and no ACK received from NMS.rw INTEGER ( 5..120 ) .1.3.6.1.4.1.568.8.9.2 |
trapAckFromMngrTrap Acknowledgement Indication: When trapAckEnable
object == enabled NMS has to ACK every trap received.rw Enumeration .1.3.6.1.4.1.568.8.9.3 |