LEXMARK-PVT-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for LEXMARK-PVT-MIB.
196
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
196 total| Object Name |
|---|
lexmark OBJECT IDENTIFIER .1.3.6.1.4.1.641 |
RFC1213-MIB Unknown .1.3.6.1.4.1.641 |
adapter OBJECT IDENTIFIER .1.3.6.1.4.1.641.1 |
irClearedThe condition on the printer has been cleared. TRAP-TYPE .1.3.6.1.4.1.641.1.0.0 |
irConditionAn error condition exists on the printer TRAP-TYPE .1.3.6.1.4.1.641.1.0.1 |
irOutputFullThe printers output bin is full. TRAP-TYPE .1.3.6.1.4.1.641.1.0.2 |
irLoadPaperLoad paper on the printer TRAP-TYPE .1.3.6.1.4.1.641.1.0.3 |
irPaperJamPaper jam on the printer. TRAP-TYPE .1.3.6.1.4.1.641.1.0.4 |
irTonerLowToner low on the printer TRAP-TYPE .1.3.6.1.4.1.641.1.0.5 |
irServiceReqService required on the printer TRAP-TYPE .1.3.6.1.4.1.641.1.0.6 |
irDiskErrDisk error on the printer TRAP-TYPE .1.3.6.1.4.1.641.1.0.7 |
irCoverOpenCover open on the printer TRAP-TYPE .1.3.6.1.4.1.641.1.0.8 |
irPageComplexityPage complexity error on the printer TRAP-TYPE .1.3.6.1.4.1.641.1.0.9 |
irOfflineThe printer is offline TRAP-TYPE .1.3.6.1.4.1.641.1.0.10 |
irClearedTypeIIThe condition on the printer has been cleared. TRAP-TYPE .1.3.6.1.4.1.641.1.0.11 |
opsys OBJECT IDENTIFIER .1.3.6.1.4.1.641.1.1 |
opsysCodeRevA textual identification of network adapter's firmware revision
level. For example: 7.15.1ro DisplayString .1.3.6.1.4.1.641.1.1.1 |
opsysJobTimeoutThe adapter job timeout period in seconds.rw INTEGER .1.3.6.1.4.1.641.1.1.2 |
opsysCurrentJobA textual description of the currently printing job containing
the Source NOS, Source server, Source user, Job number, and Job
size, separated by CR LF. A NULL string indicates no active job.
For multiport adapters, this reflects job status of printer port 1.ro DisplayString .1.3.6.1.4.1.641.1.1.3 |
opsysRAMSizeThe size of the network adapter's RAM in bytes.ro INTEGER .1.3.6.1.4.1.641.1.1.4 |
opsysNVRAMSizeThe size of the network adapter's NVRAM in bytes.ro INTEGER .1.3.6.1.4.1.641.1.1.5 |
opsysROMSizeThe size of the network adapter's ROM in bytes.ro INTEGER .1.3.6.1.4.1.641.1.1.6 |
opsysROMTypeA textual description of the network adapter's ROM technology.
Currently valid types are: MASK_ROM, OTP, FLASH, UV_EPROM,
EEPROM, and OTHER.ro DisplayString .1.3.6.1.4.1.641.1.1.7 |
opsysProtocolsA bitmap representing the protocols supported by the network adapter.
Bit Value Protocol
0 1 LexLink
1 2 Netware
2 4 AppleTalk
3 8 TCP/IP
4 16 reserved
5 32 reserved
6 64 NDSro INTEGER .1.3.6.1.4.1.641.1.1.8 |
opsysTimeToResetThe amount of time remaining until the adapter performs a power
on reset. A value of -1 indicates no reset is scheduled.
Setting to 0 causes the adapter to reset immediately. The only
valid set value is 0.rw INTEGER .1.3.6.1.4.1.641.1.1.9 |
opsysCardPartNoA textual representation of the network adapter's part number.ro DisplayString .1.3.6.1.4.1.641.1.1.10 |
opsysCardECA textual representation of the network adapter's EC level.ro DisplayString .1.3.6.1.4.1.641.1.1.11 |
opsysCurrentJobTableA table of current job information for each of the network
adapter's printer ports. SEQUENCE OF OpsysCurrentJobEntry .1.3.6.1.4.1.641.1.1.12 |
opsysCurrentJobEntryAn entry containing job information for one printer port. OpsysCurrentJobEntry .1.3.6.1.4.1.641.1.1.12.1 |
opsysCurrentJobEntryIndexA unique value used by the adapter to identify job information
for one printer port. Each entry corresponds to a value
lexhdwrPortTableIndex.ro INTEGER .1.3.6.1.4.1.641.1.1.12.1.1 |
opsysCurrentJobStringA textual description of the this printer port's currently
printing job containing the Source NOS, Source server,
Source user, Job number, and Job size, separated by CR LF.
A NULL string indicates no active job.ro DisplayString .1.3.6.1.4.1.641.1.1.12.1.2 |
opsysDeviceTypeA two byte code representing the adapter's type.ro OCTET STRING .1.3.6.1.4.1.641.1.1.13 |
opsysAdapterNameA Unicode representation of the adapter's name.ro OCTET STRING .1.3.6.1.4.1.641.1.1.14 |
opsysAdapterCapabilitiesA bitmap representing the capabilities of the adapter.
Bit Value Frame type
31 0x80000000 NPANT via Netware and IP
30 0x40000000 Receive-only Fax
29 0x20000000 reserved
28 0x10000000 Adapter HTTP
27 0x08000000 Printer HTTP
26 0x04000000 HTTP Configuration Page
25 0x02000000 Copier Optionro OCTET STRING .1.3.6.1.4.1.641.1.1.15 |
lexlink OBJECT IDENTIFIER .1.3.6.1.4.1.641.1.2 |
lexlinkActivatedThe activation status of the LexLink protocol. If this
variable is changed, the adapter must be reset before the
change will take effect. See opsysTimeToReset.rw Enumeration .1.3.6.1.4.1.641.1.2.1 |
lexlinkNicknameThe nickname assigned to the adapter for the LexLink protocol.
Note that some adapters may not support the maximum length.rw DisplayString .1.3.6.1.4.1.641.1.2.2 |
lexipx OBJECT IDENTIFIER .1.3.6.1.4.1.641.1.3 |
lexipxActivatedThe activation status of the Netware protocol. If this variable
is changed, the adapter must be reset before the change will take
effect. See opsysTimeToReset.rw Enumeration .1.3.6.1.4.1.641.1.3.1 |
lexipxLoginNameThe adapter's Netware login name. If this variable is changed, the
adapter must be reset before the change will take effect. See
opsysTimeToReset.rw DisplayString .1.3.6.1.4.1.641.1.3.2 |
lexipxNetNumberThe network number of the Netware network to which the adapter is
connected.ro DisplayString .1.3.6.1.4.1.641.1.3.3 |
lexipxSAPModeThe network adapter's current Netware SAP'ing status.rw Enumeration .1.3.6.1.4.1.641.1.3.4 |
lexipxServerModeThe current Netware server mode of the adapter. If this variable
is changed, the adapter must be reset before the change will take
effect. See opsysTimeToReset.rw Enumeration .1.3.6.1.4.1.641.1.3.5 |
lexipxNumPortsThe number of Netware printer ports.ro INTEGER .1.3.6.1.4.1.641.1.3.6 |
lexipxPortInfoTableA table of Netware printer port information. SEQUENCE OF LexipxPortInfoEntry .1.3.6.1.4.1.641.1.3.7 |
lexipxPortInfoEntryAn entry containing Netware printer port information. LexipxPortInfoEntry .1.3.6.1.4.1.641.1.3.7.1 |
lexipxPortInfoIndexA unique value used by the adapter to identify Netware printer ports.ro INTEGER .1.3.6.1.4.1.641.1.3.7.1.1 |
lexipxPortInfoPollIntvlThe Netware queue polling interval for this printer port.rw INTEGER .1.3.6.1.4.1.641.1.3.7.1.2 |
lexipxPortInfoEnableThe Netware queue status of this printer port.rw Enumeration .1.3.6.1.4.1.641.1.3.7.1.3 |
lexipxPortInfoBannerPageThe Netware queue banner page status for this printer port.ro Enumeration .1.3.6.1.4.1.641.1.3.7.1.4 |
lexipxNumPrefServersThe maximum number of preferred Netware servers supported by this
network adapter.ro INTEGER .1.3.6.1.4.1.641.1.3.8 |
lexipxPrefSrvrTableA table of the network adapter's preferred Netware servers. SEQUENCE OF LexipxPrefSrvrEntry .1.3.6.1.4.1.641.1.3.9 |
lexipxPrefSrvrEntryAn entry containing preferred Netware server information. LexipxPrefSrvrEntry .1.3.6.1.4.1.641.1.3.9.1 |
lexipxPrefSrvrIndexA unique value used by the adapter to identify preferred Netware
servers.ro INTEGER .1.3.6.1.4.1.641.1.3.9.1.1 |
lexipxPrefSrvrNameThe name of this preferred Netware server. If this variable is
changed, the adapter must be reset before the change will take
effect. See opsysTimeToReset.rw DisplayString .1.3.6.1.4.1.641.1.3.9.1.2 |
lexipxConnSrvrTableA table of connected Netware server information. SEQUENCE OF LexipxConnSrvrEntry .1.3.6.1.4.1.641.1.3.10 |
lexipxConnSrvrEntryAn entry containing connected Netware server information. LexipxConnSrvrEntry .1.3.6.1.4.1.641.1.3.10.1 |
lexipxConnSrvrIndexA unique value used by the adapter to identify connected Netware
servers.ro INTEGER .1.3.6.1.4.1.641.1.3.10.1.1 |
lexipxConnSrvrNameThe name of this connected Netware server.ro DisplayString .1.3.6.1.4.1.641.1.3.10.1.2 |
lexipxConnSrvrNetThe Netware network number of this connected Netware server.ro DisplayString .1.3.6.1.4.1.641.1.3.10.1.3 |
lexipxConnSrvrNodeThe Netware node address of the connected Netware server.ro DisplayString .1.3.6.1.4.1.641.1.3.10.1.4 |
lexipxConnSrvrConnNumThe connection number of the connected Netware server (pserver
mode only).ro INTEGER .1.3.6.1.4.1.641.1.3.10.1.5 |
lexipxConnSrvrConnIdThe connection ID of the connected Netware server (rprinter mode
only).ro INTEGER .1.3.6.1.4.1.641.1.3.10.1.6 |
lexipxConnSrvrPSConnIDThe connection ID of the connected Netware pserver (rprinter mode
only).ro INTEGER .1.3.6.1.4.1.641.1.3.10.1.7 |
lexipxFrameTypeA bitmap of the supported IPX frame types.
Bit Value Frame type
0 1 Token-Ring
1 2 Token-Ring Source Routed
2 4 Token-Ring SNAP
3 8 Token-Ring SNAP Source Routed
4 16 Ethernet 802.2
5 32 Ethernet 802.3
6 64 Ethernet Type 2
7 128 Ethernet SNAPrw INTEGER .1.3.6.1.4.1.641.1.3.11 |
lexipxTrapTableA table of IPX trap destination configurations. SEQUENCE OF LexipxTrapEntry .1.3.6.1.4.1.641.1.3.12 |
lexipxTrapEntryAn entry containing an IPX trap destination's configuration. LexipxTrapEntry .1.3.6.1.4.1.641.1.3.12.1 |
lexipxTrapIndexA unique value used by the adapter to identify IPX trap destinations.ro INTEGER .1.3.6.1.4.1.641.1.3.12.1.1 |
lexipxTrapMaskThe trap mask for the trap destination. It is implemented as a
bitmap specifying a mask of intervention required conditions for
which the adapter should send trap messages. Setting a bit to 1
enables the corresponding trap. A value of 511 will cause the
adapter to send traps for all intervention required conditions.
The bitmap is defined below:
Bit Value Condition
0 1 Output hopper full
1 2 Load Paper
2 4 Paper Jam
3 8 Toner Low
4 16 Service Required
5 32 Disk Error
6 64 Cover Opened
7 128 Page Complexity Error
8 256 Offlinerw INTEGER .1.3.6.1.4.1.641.1.3.12.1.2 |
lexipxTrapNetworkAddressThe IPX network address of the trap destination. (4 bytes)rw OCTET STRING .1.3.6.1.4.1.641.1.3.12.1.3 |
lexipxTrapNodeAddressThe IPX node address of the trap destination. (6 bytes)rw OCTET STRING .1.3.6.1.4.1.641.1.3.12.1.4 |
lexipxTrapTypeThe type of SNMP over IPX traps that will be sent by the adapter.
Setting this variable to multiplexed(1) configures all intervention
required conditions to send an irCondition trap (specific trap
number 1) and for the clearing of intervention required conditions
to send an irCleared trap (specific trap number 0).
Setting this variable to individual(2) causes each intervention
required condition to send its corresponding trap (specific traps
numbered 2 through 10) and for the clearing of intervention required
conditions to cause an irClearedTypeII trap (specific trap number 11).
See the Trap Definitions Group for more information.
Individual(2) is the default for IPX and is necessary for NMS
annotations.rw Enumeration .1.3.6.1.4.1.641.1.3.13 |
lexipxGSQThe General Service Query (GSQ) interval. This is the period
in seconds that the adapter waits after a failed GSQ before
attempting another as it searches for Netware servers.rw INTEGER .1.3.6.1.4.1.641.1.3.14 |
lextalk OBJECT IDENTIFIER .1.3.6.1.4.1.641.1.4 |
lextalkActivatedThe activation status of the AppleTalk protocol. If this
variable is changed, the adapter must be reset before the
change will take effect. See opsysTimeToReset.rw Enumeration .1.3.6.1.4.1.641.1.4.1 |
lextalkAddressThe AppleTalk Address of the network card.
This variable is not implemented on the XLe adapters.ro DisplayString .1.3.6.1.4.1.641.1.4.2 |
lextalkNameThe AppleTalk name of this adapter.
This variable is not implemented on the XLe adapters.ro DisplayString .1.3.6.1.4.1.641.1.4.3 |
lextalkZoneThe AppleTalk zone name of this adapter.
This variable is not implemented on the XLe adapters.ro DisplayString .1.3.6.1.4.1.641.1.4.4 |
lextalkTypeThe AppleTalk type of this adapter.
This variable is not implemented on the XLe adapters.ro DisplayString .1.3.6.1.4.1.641.1.4.5 |
lextcp OBJECT IDENTIFIER .1.3.6.1.4.1.641.1.5 |
lextcpActivatedThe activation status of the TCP/IP Protocol. If this
variable is changed, the adapter must be reset before the
change will take effect. See opsysTimeToReset.rw Enumeration .1.3.6.1.4.1.641.1.5.1 |
lextcpBootpEnableThe status of whether or not BOOTP is attempted to determine
the IP parameters. If this variable is changed, the adapter
must be reset before the change will take effect. See
opsysTimeToReset.rw Enumeration .1.3.6.1.4.1.641.1.5.2 |
lextcpAddressServThe IP address of the DHCP, BOOTP, or RARP server that
provided the adapter's IP address.ro IpAddress .1.3.6.1.4.1.641.1.5.3 |
lextcpNumNPAPserversThe maximum number of concurrent NPAP over TCP server
connections.ro INTEGER .1.3.6.1.4.1.641.1.5.4 |
lextcpNPAPserversTableA table of NPAP over TCP server information. SEQUENCE OF LextcpNPAPserversEntry .1.3.6.1.4.1.641.1.5.5 |
lextcpNPAPserversEntryAn entry containing NPAP over TCP server information. LextcpNPAPserversEntry .1.3.6.1.4.1.641.1.5.5.1 |
lextcpNPAPserverIndexA unique value used by the adapter to identify NPAP
over TCP servers.ro INTEGER .1.3.6.1.4.1.641.1.5.5.1.1 |
lextcpNPAPserverAddressThe IP address of this NPAP over TCP server.ro IpAddress .1.3.6.1.4.1.641.1.5.5.1.2 |
lexhttp OBJECT IDENTIFIER .1.3.6.1.4.1.641.1.5.6 |
lexhttpEnableThe status of whether the adapter will enable the HTTP server.
If this variable is changed, the adapter must be reset before
the change will take effect. See opsysTimeToReset.rw Enumeration .1.3.6.1.4.1.641.1.5.6.1 |
lexhttpNumLinksThe number of configurable HTTP links for the adapter.ro INTEGER .1.3.6.1.4.1.641.1.5.6.2 |
lexhttpBytesRemainingThe number of bytes available to store HTTP link and label
information.ro INTEGER .1.3.6.1.4.1.641.1.5.6.3 |
lexhttpResetLinksA control for restoring default values for HTTP link settings.
Setting the variable to reset will cause all of the
HTTP link settings to be reset to their default values.rw Enumeration .1.3.6.1.4.1.641.1.5.6.4 |
lexhttpLinkTableA table of HTTP Link settings. SEQUENCE OF LexhttpLinkTableEntry .1.3.6.1.4.1.641.1.5.6.5 |
lexhttpLinkTableEntryAn entry containing HTTP link settings. LexhttpLinkTableEntry .1.3.6.1.4.1.641.1.5.6.5.1 |
lexhttpLinkTableIndexA unique value used by the adapter to identify HTTP link settings.ro INTEGER .1.3.6.1.4.1.641.1.5.6.5.1.1 |
lexhttpLinkTableStatusThe status of the HTTP link.
Get operation:
linkOff
personalOn
useDefault
defaultOff
defaultOn
eraseCustom
Set operation:
linkOff
customOn
useDefault
. link in defaultOn status
defaultOff
defaultOn
eraseCustom
. link in linkOff statusrw Enumeration .1.3.6.1.4.1.641.1.5.6.5.1.2 |
lexhttpLinkTableLabelThe text to be displayed as the label of this HTTP link. It may be set
to define a custom link. Note that when read, this always reflects what
the server would display. As such, if the status of this link is
defaultOn, it will not return your custom label if read even though it
has been stored. Setting the status for this link to customOn will
activate your custom link label. Remember that setting the status of
this link to eraseCustom or useDefault clears this variable.rw DisplayString .1.3.6.1.4.1.641.1.5.6.5.1.3 |
lexhttpLinkTableURLThe URL to be hyperlinked to by the HTTP link. It may be set to
define a custom link. Note that when read, this always reflects what
the server would use. As such, if the status of this link is
defaultOn, it will not return your custom URL if read even though it
has been stored. Setting the status for this link to customOn will
activate your custom link URL. Remember that setting the status of
this link to eraseCustom or useDefault clears this variable.rw DisplayString .1.3.6.1.4.1.641.1.5.6.5.1.4 |
lexhttpConfigEnableThe status of whether HTTP configuration page is enabled.rw Enumeration .1.3.6.1.4.1.641.1.5.6.6 |
lexdhcp OBJECT IDENTIFIER .1.3.6.1.4.1.641.1.5.7 |
lexdhcpDhcpEnableThe status of whether DHCP is enabled.rw Enumeration .1.3.6.1.4.1.641.1.5.7.1 |
lexdhcpRarpEnableThe status of whether RARP is enabled.rw Enumeration .1.3.6.1.4.1.641.1.5.7.2 |
lexdhcpAddressSourceThe method by which the current IP parameters were obtained.ro Enumeration .1.3.6.1.4.1.641.1.5.7.3 |
lexdhcpWinsStatusThe adapter's WINS server registration status.ro Enumeration .1.3.6.1.4.1.641.1.5.7.4 |
lexdhcpWinsServerThe IP address of the WINS server.ro IpAddress .1.3.6.1.4.1.641.1.5.7.5 |
lexdhcpHostnameThe adapter's TCP/IP hostname.rw DisplayString .1.3.6.1.4.1.641.1.5.7.6 |
lexdhcpLeaseLengthThe length of the adapter's DHCP address lease in seconds.ro INTEGER .1.3.6.1.4.1.641.1.5.7.7 |
lexdhcpTimetoExpireThe number of seconds until the DHCP address lease expires.ro INTEGER .1.3.6.1.4.1.641.1.5.7.8 |
lexdhcpDNSServerThe IP address of the DNS server.rw IpAddress .1.3.6.1.4.1.641.1.5.7.9 |
lexhdwr OBJECT IDENTIFIER .1.3.6.1.4.1.641.1.6 |
lexhdwrNumPortsThe number of printer ports supported by this network adapter.ro INTEGER .1.3.6.1.4.1.641.1.6.1 |
lexhdwrPortTableA table of the adapter's printer port hardware settings. SEQUENCE OF LexhdwrPortTableEntry .1.3.6.1.4.1.641.1.6.2 |
lexhdwrPortTableEntryAn entry containing printer port hardware settings. LexhdwrPortTableEntry .1.3.6.1.4.1.641.1.6.2.1 |
lexhdwrPortTableIndexA unique value used by the adapter to identify printer ports.ro INTEGER .1.3.6.1.4.1.641.1.6.2.1.1 |
lexhdwrPortTableTypeThe type of attachment for this printer port.ro Enumeration .1.3.6.1.4.1.641.1.6.2.1.2 |
lexhdwrPortTableParm1For serial and parallel ports, this is the port timeout in seconds.
For internal ports, this parameter is unused.rw INTEGER .1.3.6.1.4.1.641.1.6.2.1.3 |
lexhdwrPortTableParm2For serial ports, this is the baud rate in bits per second.
For parallel ports, this is the port mode and is defined as follows:
standard(0),
enhanced(1)
For internal ports, this parameter is unused.rw INTEGER .1.3.6.1.4.1.641.1.6.2.1.4 |
lexhdwrPortTableParm3For serial ports, this is the parity and is defined as follows:
none(0),
odd(1),
even(2),
space(3),
mark(4)
For parallel and internal ports, this parameter is unused.rw INTEGER .1.3.6.1.4.1.641.1.6.2.1.5 |
lexhdwrPortTableParm4For serial ports, this is the number of data bits.
For parallel and internal ports, this parameter is unused.rw INTEGER .1.3.6.1.4.1.641.1.6.2.1.6 |
lexhdwrPortTableParm5For serial ports, this is the number of stop bits and is defined
as follows:
bitsOne(2),
bitsOneAndHalf(3),
bitsTwo(4)
For parallel and internal ports, this parameter is unused.rw INTEGER .1.3.6.1.4.1.641.1.6.2.1.7 |
lexhdwrPortTableParm6For serial ports, this is the pacing mode and is defined as follows:
paceDtr(0),
paceXonXff(1)
For non XLe parallel ports, this is the parallel protocol and is defined
as follows:
auto(2),
ecp(3),
byte(4),
nibble(5),
compatible(6)
For internal ports, and XLe parallel ports this parameter is unused.rw INTEGER .1.3.6.1.4.1.641.1.6.2.1.8 |
lexhdwrPortTableParm7For all ports, this is the configured NPAP mode.rw Enumeration .1.3.6.1.4.1.641.1.6.2.1.9 |
lexhdwrPortTableParm8For all ports, this is the NPAP status.ro Enumeration .1.3.6.1.4.1.641.1.6.2.1.10 |
lexhdwrPortTableParm9For serial ports, this is the class of device attached.
This variable is unused on the XLe adapters.rw Enumeration .1.3.6.1.4.1.641.1.6.2.1.11 |
lexmac OBJECT IDENTIFIER .1.3.6.1.4.1.641.1.7 |
lexmacTypeA textual representation of network medium to which the network
adapter is attached (e.g. Ethernet).ro DisplayString .1.3.6.1.4.1.641.1.7.1 |
lexmacSpeedThe speed, in bits per second, of the network medium to which the
network adapter is attached.ro Gauge .1.3.6.1.4.1.641.1.7.2 |
lexmacConnTypeThe connection type by which the network adapter is connected to
the network medium.ro Enumeration .1.3.6.1.4.1.641.1.7.3 |
lexmacUAAThe network adapter's universally administered network address.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.641.1.7.4 |
lexmacLAAThe network adapter's locally administered network address. A
value of all zeros indicates that the LAA is not in use.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.641.1.7.5 |
lextrap OBJECT IDENTIFIER .1.3.6.1.4.1.641.1.8 |
lextrapDestNumThe maximum number of IP trap destinations supported by this
network adapter.ro INTEGER .1.3.6.1.4.1.641.1.8.1 |
lextrapDestTableA table of IP trap destination configurations. SEQUENCE OF LextrapDestEntry .1.3.6.1.4.1.641.1.8.2 |
lextrapDestEntryAn entry containing an IP trap destination configuration. LextrapDestEntry .1.3.6.1.4.1.641.1.8.2.1 |
lextrapDestIndexA unique value used by the adapter to identify IP trap destinations.ro INTEGER .1.3.6.1.4.1.641.1.8.2.1.1 |
lextrapDestIPAddrThe IP address of the trap destination.rw IpAddress .1.3.6.1.4.1.641.1.8.2.1.2 |
lextrapDestMaskThe trap mask for the trap destination. It is implemented as a
bitmap specifying a mask of intervention required conditions for
which the adapter should send trap messages. Setting a bit to 1
enables the corresponding trap. A value of 1023 will cause the
adapter to send traps for all intervention required conditions.
The bitmap is defined below:
Bit Value Condition
0 1 Output hopper full
1 2 Load Paper
2 4 Paper Jam
3 8 Toner Low
4 16 Service Required
5 32 Disk Error
6 64 Cover Opened
7 128 Page Complexity Error
8 256 Offline
9 512 Printer MIB (RFC 1759)rw INTEGER .1.3.6.1.4.1.641.1.8.2.1.3 |
lextrapIPTrapTypeThe type of SNMP over IP traps that will be sent by the adapter.
Setting this variable to multiplexed(1) configures all intervention
required conditions to send an irCondition trap (specific trap number 1)
and for the clearing of intervention required conditions to send an
irCleared trap (specific trap number 0).
Setting this variable to individual(2) causes each intervention required
condition to send its corresponding trap (specific traps numbered 2
through 10) and for the clearing of intervention required conditions
to cause an irClearedTypeII trap (specific trap number 11).
See the Trap Definitions Group for more information.
Type 1 is the default for IP.rw Enumeration .1.3.6.1.4.1.641.1.8.3 |
time OBJECT IDENTIFIER .1.3.6.1.4.1.641.1.9 |
timeResetA control for initiating an update of the system time and date using
the specified timeSource. Setting the variable to reset will cause
the system to update it's time and date using the specified time source.
See timeSource.rw Enumeration .1.3.6.1.4.1.641.1.9.1 |
timeSourceThe source for setting the system time and date. If this variable
is changed, the time must be reset before the change will have an effect.
See timeReset.rw Enumeration .1.3.6.1.4.1.641.1.9.2 |
timeUTCOffsetThe offset in minutes from UTC (formerly GMT) of local time. Use a
negative value if West of UTC. Use a positive value if East of UTC.rw INTEGER (-720..720) .1.3.6.1.4.1.641.1.9.3 |
timeDSTEnableThe status of whether automatic Daylight Savings Time adjust is enabled.
See timeDSTStartDate, timeDSTEndDate, and timeDSTOffset for configuration
options.rw Enumeration .1.3.6.1.4.1.641.1.9.4 |
timeDSTStartDateA textual representation of the day and time the Daylight Savings Time
adjust should start if enabled (see timeDSTEnable). The format of string
is as follows:
Byte Meaning
0 Which occurence in the month of the day specified in byte 1.
Valid values are:
F => First Occurence
1 => First Occurence
2 => Second Occurence
3 => Third Occurence
4 => Fourth Occurence
5 => Fifth Occurence
L => Last Occurence
1 A 1-digit field indicating the day of week (0=Sun..6=Sat)
2-3 A 2-digit field indicating the month.
4-5 A 2-digit field indicating the hour
6-7 A 2-digit field indicating the minute
8-9 A 2-digit field indicating the second
The default setting is F004020000 which corresponds to the first Sunday
of April at 2:00:00 am.rw OCTET STRING .1.3.6.1.4.1.641.1.9.5 |
timeDSTEndDateA textual representation of the day and time the Daylight Savings Time
adjust should end if enabled (see timeDSTEnable). The format of string
is as defined for timeDSTStartDate
The default setting is L010020000 which corresponds to the last Sunday
of October at 2:00:00 am.rw OCTET STRING .1.3.6.1.4.1.641.1.9.6 |
timeDSTOffsetThe offset in minutes that should be applied to local time during Daylight
Savings Time.rw INTEGER .1.3.6.1.4.1.641.1.9.7 |
timeServerAddressIf the specified time source is NTP (see timeSource), this is the IP address
of the NTP server to use. Otherwise, the value is ignored.rw IpAddress .1.3.6.1.4.1.641.1.9.8 |
timeServerNameIf the specified time source is NTP (see timeSource), and the NTP server
address is not set (0.0.0.0), this is the DNS domainname of the NTP server.
If the specified time source is Netware (see timeSource), the is the name of
Netware server. Otherwise, the value is ignored.rw DisplayString .1.3.6.1.4.1.641.1.9.9 |
printer OBJECT IDENTIFIER .1.3.6.1.4.1.641.2 |
prtgen OBJECT IDENTIFIER .1.3.6.1.4.1.641.2.1 |
prtgenNumberThe number of printers, regardless of their current state,
available to this adapter.ro INTEGER .1.3.6.1.4.1.641.2.1.1 |
prtgenInfoTableA table of the network adapter's attached printer information. SEQUENCE OF PrtgenInfoEntry .1.3.6.1.4.1.641.2.1.2 |
prtgenInfoEntryAn entry containing attached printer information. PrtgenInfoEntry .1.3.6.1.4.1.641.2.1.2.1 |
prtgenPrinterIndexA unique value used by the network adapter to identify attached
printers.ro INTEGER .1.3.6.1.4.1.641.2.1.2.1.1 |
prtgenPrinterNameA textual description of the make and model of the attached printer,
if known.ro DisplayString .1.3.6.1.4.1.641.2.1.2.1.2 |
prtgenPeripheralIDA textual description of the peripheral ID of the attached printer
as defined by the IEEE 1284 standard, if known.ro DisplayString .1.3.6.1.4.1.641.2.1.2.1.3 |
prtgenCodeRevisionA textual representation of the code revision level of the attached
printer, if known.ro DisplayString .1.3.6.1.4.1.641.2.1.2.1.4 |
prtgenResValueThis object is currently unused and reserved.ro INTEGER .1.3.6.1.4.1.641.2.1.2.1.5 |
prtgenSerialNoA textual representation of the serial number of the attached
printer, if known.ro DisplayString .1.3.6.1.4.1.641.2.1.2.1.6 |
prtgenStatusTableA table of the network adapter's attached printer status. SEQUENCE OF PrtgenStatusEntry .1.3.6.1.4.1.641.2.1.3 |
prtgenStatusEntryAn entry containing attached printer status. PrtgenStatusEntry .1.3.6.1.4.1.641.2.1.3.1 |
prtgenStatPrinterIndexA unique value used by the network adapter to identify attached
printers.ro INTEGER .1.3.6.1.4.1.641.2.1.3.1.1 |
prtgenStatusIRCThe printer's current intervention required code.ro INTEGER .1.3.6.1.4.1.641.2.1.3.1.2 |
prtgenStatusOutHopFullThe printer's current output hopper status.ro Enumeration .1.3.6.1.4.1.641.2.1.3.1.3 |
prtgenStatusInputEmptyThe printer's current active input paper tray status.ro Enumeration .1.3.6.1.4.1.641.2.1.3.1.4 |
prtgenStatusPaperJamThe printer's current paper path status.ro Enumeration .1.3.6.1.4.1.641.2.1.3.1.5 |
prtgenStatusTonerErrorThe printer's current toner supply status.ro Enumeration .1.3.6.1.4.1.641.2.1.3.1.6 |
prtgenStatusSrvcReqdThe printer's current service required status.ro Enumeration .1.3.6.1.4.1.641.2.1.3.1.7 |
prtgenStatusDiskErrorThe printer's current disk sub-system status.ro Enumeration .1.3.6.1.4.1.641.2.1.3.1.8 |
prtgenStatusCoverOpenThe printer's current cover status.ro Enumeration .1.3.6.1.4.1.641.2.1.3.1.9 |
prtgenStatusPageComplexThe printer's current complex page status.ro Enumeration .1.3.6.1.4.1.641.2.1.3.1.10 |
prtgenStatusLineStatusThe printer's current online/offline status.ro Enumeration .1.3.6.1.4.1.641.2.1.3.1.11 |
prtgenStatusBusyThe printer's current bust status.ro Enumeration .1.3.6.1.4.1.641.2.1.3.1.12 |
prtgenStatusWaitingThe printer's current waiting status.ro Enumeration .1.3.6.1.4.1.641.2.1.3.1.13 |
prtgenStatusWarmingThe printer's current warming status.ro Enumeration .1.3.6.1.4.1.641.2.1.3.1.14 |
prtgenStatusPrintingThe printer's current printing status.ro Enumeration .1.3.6.1.4.1.641.2.1.3.1.15 |
attachment OBJECT IDENTIFIER .1.3.6.1.4.1.641.3 |
fax OBJECT IDENTIFIER .1.3.6.1.4.1.641.3.1 |
faxNumberThe number of fax modems attached to the adapter.ro INTEGER .1.3.6.1.4.1.641.3.1.1 |
faxTableA table of the network adapter's attached fax modems configuration data. SEQUENCE OF FaxEntry .1.3.6.1.4.1.641.3.1.2 |
faxEntryAn entry containing attached fax modem configuration data. FaxEntry .1.3.6.1.4.1.641.3.1.2.1 |
faxIndexA unique value used by the adapter to identify fax ports.ro INTEGER .1.3.6.1.4.1.641.3.1.2.1.1 |
faxPortThe network adapter's port to which this modem is attached.ro Enumeration .1.3.6.1.4.1.641.3.1.2.1.2 |
faxAdapterCapabilitiesA bitmap representing the fax capabilities of the network adapter.
Bit Value Capabilities
0 1 Fine Resolution
1 2 2D Encoding
2 4 T6 Encoding
3 8 ECM
4 16 Binary File Transfer
5 32 300 x 300
6 64 400 x 400
7 128 200 x 400
8 256 Uncompressed Mode
9 512 255mm Width
10 1024 303mm Width
11 2048 Legal Length
12 4096 Unlimited Length
13 8192 V.17 (14400)
14 16384 V.33 (14400)
15 32768 V.29 and V.27 (9600)
16 65536 V.29 (9600)
17 131072 V.27 (4800)
18 262144 V27 (2400)ro INTEGER .1.3.6.1.4.1.641.3.1.2.1.3 |
faxModemCapabilitiesA bitmap representing the fax capabilities of the attached modem.
Bit Value Capabilities
0 1 Fine Resolution
1 2 2D Encoding
2 4 T6 Encoding
3 8 ECM
4 16 Binary File Transfer
5 32 300 x 300
6 64 400 x 400
7 128 200 x 400
8 256 Uncompressed Mode
9 512 255mm Width
10 1024 303mm Width
11 2048 Legal Length
12 4096 Unlimited Length
13 8192 V.17 (14400)
14 16384 V.33 (14400)
15 32768 V.29 and V.27 (9600)
16 65536 V.29 (9600)
17 131072 V.27 (4800)
18 262144 V27 (2400)ro INTEGER .1.3.6.1.4.1.641.3.1.2.1.4 |
faxSelectedCapabilitiesA bitmap representing the user selected fax capabilities.
Bit Value Capabilities
0 1 Fine Resolution
1 2 2D Encoding
2 4 T6 Encoding
3 8 ECM
4 16 Binary File Transfer
5 32 300 x 300
6 64 400 x 400
7 128 200 x 400
8 256 Uncompressed Mode
9 512 255mm Width
10 1024 303mm Width
11 2048 Legal Length
12 4096 Unlimited Length
13 8192 V.17 (14400)
14 16384 V.33 (14400)
15 32768 V.29 and V.27 (9600)
16 65536 V.29 (9600)
17 131072 V.27 (4800)
18 262144 V27 (2400)rw INTEGER .1.3.6.1.4.1.641.3.1.2.1.5 |
faxActiveCapabilitiesA bitmap representing the active fax capabilities. This is
the logical and of faxAdapterCapabilities, faxModemCapabilities,
and faxSelectedCapabilities.
Bit Value Capabilities
0 1 Fine Resolution
1 2 2D Encoding
2 4 T6 Encoding
3 8 ECM
4 16 Binary File Transfer
5 32 300 x 300
6 64 400 x 400
7 128 200 x 400
8 256 Uncompressed Mode
9 512 255mm Width
10 1024 303mm Width
11 2048 Legal Length
12 4096 Unlimited Length
13 8192 V.17 (14400)
14 16384 V.33 (14400)
15 32768 V.29 and V.27 (9600)
16 65536 V.29 (9600)
17 131072 V.27 (4800)
18 262144 V27 (2400)ro INTEGER .1.3.6.1.4.1.641.3.1.2.1.6 |
faxIDStringThe textual identification that is used to identify this fax device.
This text is sent to a connected fax device at the start of a call.rw DisplayString .1.3.6.1.4.1.641.3.1.2.1.7 |
faxInitStringThe commands used be the network adapter to initialize an attached modem.rw DisplayString .1.3.6.1.4.1.641.3.1.2.1.8 |
faxNumberRingsThe number of rings that the network adapter should wait before answering.rw INTEGER .1.3.6.1.4.1.641.3.1.2.1.9 |
faxScalingThe mechanism used to resolve size descrepancies between the received fax
the printer's available forms.rw Enumeration .1.3.6.1.4.1.641.3.1.2.1.10 |
faxBinaryEncodingThe encoding used when sending fax data to the attached printer.rw Enumeration .1.3.6.1.4.1.641.3.1.2.1.11 |
faxPrinterPortThe port (printer) to which received faxes should be printed.rw Enumeration .1.3.6.1.4.1.641.3.1.2.1.13 |
faxInputTrayThe input tray from which received faxes should be printed.
The value 255 indicates printer default.rw INTEGER .1.3.6.1.4.1.641.3.1.2.1.14 |
faxOutputBinThe output bin to which received faxes should be printed.
The value 255 indicates printer default.rw INTEGER .1.3.6.1.4.1.641.3.1.2.1.15 |