LANART-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for LANART-MIB.
32
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
32 total| Object Name |
|---|
lanart OBJECT IDENTIFIER .1.3.6.1.4.1.712 |
RFC1213-MIB Unknown .1.3.6.1.4.1.712 |
laPortStatusThe laPortStatus trap conveys a change in status
of a particular port. This trap is sent for a
given port when either of the following status
variables change for that port:
rptrPortAdminStatus, laTpLinkTest
The rptrHealth trap contains the
rptrPortOperStatus object. TRAP-TYPE .1.3.6.1.4.1.712.0.1 |
laMib1 OBJECT IDENTIFIER .1.3.6.1.4.1.712.1 |
laProducts OBJECT IDENTIFIER .1.3.6.1.4.1.712.1.1 |
laTpHub OBJECT IDENTIFIER .1.3.6.1.4.1.712.1.1.1 |
laTpHub1 OBJECT IDENTIFIER .1.3.6.1.4.1.712.1.1.1.1 |
etm120x OBJECT IDENTIFIER .1.3.6.1.4.1.712.1.1.1.1.12 |
etm160x OBJECT IDENTIFIER .1.3.6.1.4.1.712.1.1.1.1.16 |
etm240x OBJECT IDENTIFIER .1.3.6.1.4.1.712.1.1.1.1.24 |
laTpHub2 OBJECT IDENTIFIER .1.3.6.1.4.1.712.1.1.1.2 |
ete120x OBJECT IDENTIFIER .1.3.6.1.4.1.712.1.1.1.2.12 |
ete160x OBJECT IDENTIFIER .1.3.6.1.4.1.712.1.1.1.2.16 |
ete240x OBJECT IDENTIFIER .1.3.6.1.4.1.712.1.1.1.2.24 |
laTpHub3 OBJECT IDENTIFIER .1.3.6.1.4.1.712.1.1.1.3 |
bbAui OBJECT IDENTIFIER .1.3.6.1.4.1.712.1.1.1.3.0 |
bbAuiTp OBJECT IDENTIFIER .1.3.6.1.4.1.712.1.1.1.3.1 |
bbAuiBnc OBJECT IDENTIFIER .1.3.6.1.4.1.712.1.1.1.3.2 |
bbAuiTpBnc OBJECT IDENTIFIER .1.3.6.1.4.1.712.1.1.1.3.3 |
bbAui10BASE-FL OBJECT IDENTIFIER .1.3.6.1.4.1.712.1.1.1.3.4 |
laHubMib OBJECT IDENTIFIER .1.3.6.1.4.1.712.1.2 |
laSys OBJECT IDENTIFIER .1.3.6.1.4.1.712.1.2.1 |
laSysConfigSetting this object to save(1) will save all
configuration variables to non-volatile memory.
Setting this object to load(2) will configure
the hub according to the stored configuration.
Setting this object to factory(3) will configure
the hub according to the factory settings.
A return value of ok(4) means the non-volatile memory
is operational.
A return value of failed(5) means the non-volatile
memory has failed.rw Enumeration .1.3.6.1.4.1.712.1.2.1.1 |
laJoystickSetting this object to disabled(2) prevents
use of the four-position switch on the front
panel. Resetting this object to enabled(1)
allows use of the switch.rw Enumeration .1.3.6.1.4.1.712.1.2.1.2 |
laLinkAlertSetting this object enables or disables the
LinkALERT feature of the backbone 10BASE-T
or 10BASE-FL port.
A return value of not-applicable indicates that
none of the backbone ports feature LinkALERT.rw Enumeration .1.3.6.1.4.1.712.1.2.1.3 |
laTpPort OBJECT IDENTIFIER .1.3.6.1.4.1.712.1.2.2 |
laTpPortTableTable of descriptive and status information about
the ports. SEQUENCE OF LaTpPortEntry .1.3.6.1.4.1.712.1.2.2.1 |
laTpPortEntryAn entry in the table, containing information
about a single port. LaTpPortEntry .1.3.6.1.4.1.712.1.2.2.1.1 |
laTpPortGroupIndexThis object identifies the group containing the
port for which this entry contains information.ro INTEGER .1.3.6.1.4.1.712.1.2.2.1.1.1 |
laTpPortIndexThis object identifies the port within the group
for which this entry contains information.ro INTEGER .1.3.6.1.4.1.712.1.2.2.1.1.2 |
laTpLinkTestSetting this object to disabled(2) disables the
link test feature. This may be useful for
interoperation with pre-10BASE-T equipment.
Setting this object to enabled(1) enables the
feature.
A return value of failed(3) indicates a link test
failure for this port.
A return value of not-applicable(4) indicates that
the specified port does not have a link test.rw Enumeration .1.3.6.1.4.1.712.1.2.2.1.1.3 |
laTpAutoPolaritySetting this object to disabled(2) disables the
auto polarity test for this port.
Setting this object to enabled(1) enables the feature.
A return value of corrected(3) indicates that the
polarity test has sensed a reversal on the receive
wiring pair, and has corrected this fault by inverting
its receive signal.
A return value of not-applicable(4) indicates that
the specified port does not support polarity correction.rw Enumeration .1.3.6.1.4.1.712.1.2.2.1.1.4 |