JACOBS-RPL-MIB
AI MIB Summary
The JACOBS-RPL-MIB module enables monitoring of IPv6 Routing Protocol for Low-Power and Lossy Networks (RPL) instances on Jacobs-specific hardware, tracking node topology states, rank values, and DODAG (Destination-Oriented Directed Acyclic Graph) metrics. This MIB facilitates the observation of routing stability and neighbor relationships within constrained IoT and industrial sensor networks.
The MIB module for monitoring nodes implementing the IPv6 routing protocol for low power and lossy networks (RPL). Copyright (c) 2012 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info).
Main OID:
rplMib.1.3.6.1.4.1.30982.1.2
87
Objects
Active
Status
6
Dependencies
Imported Objects
Objects
87 total| Object Name |
|---|
rplMibThe MIB module for monitoring nodes implementing the IPv6 routing protocol for low power and lossy networks (RPL). Copyright (c) 2012 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info). MODULE-IDENTITY .1.3.6.1.4.1.30982.1.2 |
rplNotifications OBJECT IDENTIFIER .1.3.6.1.4.1.30982.1.2.0 |
rplObjects OBJECT IDENTIFIER .1.3.6.1.4.1.30982.1.2.1 |
rplDefaults OBJECT IDENTIFIER .1.3.6.1.4.1.30982.1.2.1.1 |
rplDefaultDISModeDetermines whether a DIS message is send upon boot-up. Changes to this value may not persist across restarts.rw RplDISMode .1.3.6.1.4.1.30982.1.2.1.1.1 |
rplDefaultDISMessagesThe number of DIS messages that are sent as an initial probe for nearby DODAGs if the DIS mode is 'send'. The value of this object is ignored if the DIS mode is 'silent'. Changes to this value may not persist across restarts.rw Unsigned32 .1.3.6.1.4.1.30982.1.2.1.1.2 |
rplDefaultDISTimeoutThe number of seconds after which a node in DIS mode 'send' in the absence of DIO messages may decide to root a floating DODAG. Changes to this value may not persist across restarts.rw Unsigned32 .1.3.6.1.4.1.30982.1.2.1.1.3 |
rplDefaultDAODelayThe default delay for aggregations before a DAO is send. Changes to this value may not persist across restarts.rw RplDAODelay UNITS "milliseconds" .1.3.6.1.4.1.30982.1.2.1.1.4 |
rplDefaultDAOAckEnabledIndicates whether DAO Acknowledgements are sent on this RPL instance. Changes to this value may not persist across restarts.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.30982.1.2.1.1.5 |
rplDefaultPreferenceThe default preference of this DODAG compared to other DODAGs within the same instance. Changes to this value may not persist across restarts.rw RplDodagPreference .1.3.6.1.4.1.30982.1.2.1.1.6 |
rplDefaultMinHopRankIncreaseThe default minimum increase of the rank in a single hop. Changes to this value may not persist across restarts.rw RplMinHopRankIncrease .1.3.6.1.4.1.30982.1.2.1.1.7 |
rplDefaultMaxRankIncreaseThe default maximum allowable increase in rank in support of local repair. If DAGMaxRankIncrease is 0 then this mechanism is disabled. Changes to this value may not persist across restarts.rw Unsigned32 .1.3.6.1.4.1.30982.1.2.1.1.8 |
rplDefaultModeOfOperationThe mode of operation of the RPL instance. Changes to this value may not persist across restarts.rw RplModeOfOperation .1.3.6.1.4.1.30982.1.2.1.1.9 |
rplDefaultIntervalDoublingsThe default Imax parameter of the DIO trickle timer. Changes to this value may not persist across restarts.rw Unsigned32 .1.3.6.1.4.1.30982.1.2.1.1.10 |
rplDefaultIntervalMinThe default Imin parameter of the DIO trickle timer. Changes to this value may not persist across restarts.rw Unsigned32 .1.3.6.1.4.1.30982.1.2.1.1.11 |
rplDefaultRedundancyConstantThe default k parameter of the DIO trickle timer. Changes to this value may not persist across restarts.rw Unsigned32 .1.3.6.1.4.1.30982.1.2.1.1.12 |
rplActive OBJECT IDENTIFIER .1.3.6.1.4.1.30982.1.2.1.2 |
rplActiveInstanceThe currently active RPL Instance. Changes to this value may not persist across restarts.rw RplInstanceID .1.3.6.1.4.1.30982.1.2.1.2.1 |
rplActiveDodagThe currently active RPL DODAG in the active RPL Instance. Changes to this value may not persist across restarts.rw InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.30982.1.2.1.2.2 |
rplActiveDodagTriggerSequenceThe DAO Trigger Sequence Number (DTSN) of the active DODAG as defined in Section 6.3.1 of RFC 6550. Changes to this value may not persist across restarts.rw Unsigned32 .1.3.6.1.4.1.30982.1.2.1.2.3 |
rplOCPTableThe table of all supported Objective Code Points (OCPs). SEQUENCE OF RplOCPEntry .1.3.6.1.4.1.30982.1.2.1.3 |
rplOCPEntryAn entry representing a supported Objective Code Point. RplOCPEntry .1.3.6.1.4.1.30982.1.2.1.3.1 |
rplOCPCodepointA supported Objective Code Point. RplObjectiveCodePoint .1.3.6.1.4.1.30982.1.2.1.3.1.1 |
rplOCPEnabledEnables the usage of this Objective Code Point. Changes to this value may not persist across restarts.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.30982.1.2.1.3.1.2 |
rplInstanceTableThe table represents information about all known RPL Instances. SEQUENCE OF RplInstanceEntry .1.3.6.1.4.1.30982.1.2.1.4 |
rplInstanceEntryAn entry representing information about a RPL Instance. RplInstanceEntry .1.3.6.1.4.1.30982.1.2.1.4.1 |
rplInstanceIDThe InstanceID of this RPL Instance. RplInstanceID .1.3.6.1.4.1.30982.1.2.1.4.1.1 |
rplInstanceDISModeReports whether a DIS message is send for this instance upon boot-up.ro RplDISMode .1.3.6.1.4.1.30982.1.2.1.4.1.2 |
rplInstanceDISMessagesThe number of DIS messages that are sent as an initial probe for nearby DODAGs if the DIS mode is 'send'.ro Unsigned32 .1.3.6.1.4.1.30982.1.2.1.4.1.3 |
rplInstanceDISTimeoutThe number of seconds after which a node in DIS mode 'send' in the absence of DIO messages may decide to root a floating DODAG.ro Unsigned32 .1.3.6.1.4.1.30982.1.2.1.4.1.4 |
rplInstanceModeOfOperationThe mode of operation of the RPL instance.ro RplModeOfOperation .1.3.6.1.4.1.30982.1.2.1.4.1.5 |
rplDodagTableThe table represents information about all locally known DODAGs. SEQUENCE OF RplDodagEntry .1.3.6.1.4.1.30982.1.2.1.5 |
rplDodagEntryAn entry representing information about a DODAG. RplDodagEntry .1.3.6.1.4.1.30982.1.2.1.5.1 |
rplDodagIndexThe index identifying a DODAG within an RPL instance. This index is used to keep the table indexes short. The RPL protocol identifies a DODAG within an RPL instance by the DODAGID. Unsigned32 .1.3.6.1.4.1.30982.1.2.1.5.1.1 |
rplDodagIDThe identifier of a DODAG root (DODAGID) of this RPL instance. The root of the DODAG reports its own IPv6 address as the DODAG root. This is uniquely identifying a DODAG within an RPL instance.ro InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.30982.1.2.1.5.1.2 |
rplDodagVersionThe version of the DODAG in this RPL instance.ro RplDodagVersionNumber .1.3.6.1.4.1.30982.1.2.1.5.1.3 |
rplDodagRankThe rank of the node within the DODAG.ro RplRank .1.3.6.1.4.1.30982.1.2.1.5.1.4 |
rplDodagStateThe status of the DODAG: other(0) An unknown state. grounded(1) The DODAG is grounded. floating(2) The DODAG is floating (not grounded).ro Enumeration .1.3.6.1.4.1.30982.1.2.1.5.1.5 |
rplDodagOCPThe Objective Code Point of this DODAG.ro RplObjectiveCodePoint .1.3.6.1.4.1.30982.1.2.1.5.1.6 |
rplDodagDAODelayThe delay for aggregations before a DAO is send.ro RplDAODelay UNITS "milliseconds" .1.3.6.1.4.1.30982.1.2.1.5.1.7 |
rplDodagDAOAckEnabledIndicates whether DAO Acknowledgements are sent on this DODAG.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.30982.1.2.1.5.1.8 |
rplDodagPreferenceHow preferred this DODAG is compared to other DODAGs within the same instance.ro RplDodagPreference .1.3.6.1.4.1.30982.1.2.1.5.1.9 |
rplDodagMinHopRankIncreaseThe minimum increase of the rank in a single hop.ro RplMinHopRankIncrease .1.3.6.1.4.1.30982.1.2.1.5.1.10 |
rplDodagMaxRankIncreaseThe maximum allowable increase in rank in support of local repair. If DAGMaxRankIncrease is 0 then this mechanism is disabled.ro Unsigned32 .1.3.6.1.4.1.30982.1.2.1.5.1.11 |
rplDodagIntervalDoublingsThe Imax parameter of the DIO trickle timer.ro Unsigned32 .1.3.6.1.4.1.30982.1.2.1.5.1.12 |
rplDodagIntervalMinThe Imin parameter of the DIO trickle timer.ro Unsigned32 .1.3.6.1.4.1.30982.1.2.1.5.1.13 |
rplDodagRedundancyConstantThe k parameter of the DIO trickle timer.ro Unsigned32 .1.3.6.1.4.1.30982.1.2.1.5.1.14 |
rplDodagPathControlSizeThe Path Control Size of this DODAG.ro RplPathControlSize .1.3.6.1.4.1.30982.1.2.1.5.1.15 |
rplDodagParentTableThe list of parents for a DODAG. SEQUENCE OF RplDodagParentEntry .1.3.6.1.4.1.30982.1.2.1.6 |
rplDodagParentEntryInformation about a known DODAG parent. RplDodagParentEntry .1.3.6.1.4.1.30982.1.2.1.6.1 |
rplDodagParentIDAn RPL parent associated with this DODAG. InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.30982.1.2.1.6.1.1 |
rplDodagParentIfThe interface over which the parent can be reached.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.30982.1.2.1.6.1.2 |
rplDodagChildTableThe list of children for a DODAG. SEQUENCE OF RplDodagChildEntry .1.3.6.1.4.1.30982.1.2.1.7 |
rplDodagChildEntryInformation about a known DODAG child. RplDodagChildEntry .1.3.6.1.4.1.30982.1.2.1.7.1 |
rplDodagChildIDAn RPL child associated with this DODAG. InetAddressIPv6 (INET-ADDRESS-MIB) .1.3.6.1.4.1.30982.1.2.1.7.1.1 |
rplDodagChildIfThe interface over which the child can be reached.ro InterfaceIndex (IF-MIB) .1.3.6.1.4.1.30982.1.2.1.7.1.2 |
rplStats OBJECT IDENTIFIER .1.3.6.1.4.1.30982.1.2.1.8 |
rplMemOverflowsThe number of memory allocation failures (e.g., routing table overflows).ro Counter32 .1.3.6.1.4.1.30982.1.2.1.8.1 |
rplParseErrorsThe number of received malformed messages.ro Counter32 .1.3.6.1.4.1.30982.1.2.1.8.2 |
rplUnknownMsgTypesThe number of received RPL messages that we dropped because the message type is not recognized by the implementation.ro Counter32 .1.3.6.1.4.1.30982.1.2.1.8.3 |
rplSecurityPolicyViolationsThe number of messages discarded because the described level of security for the message type and originator is unknown or does not meet locally maintained security policies as defined in Section 10.7. of RFC 6550.ro Counter32 .1.3.6.1.4.1.30982.1.2.1.8.4 |
rplIntegrityCheckFailuresThe number of messages discarded because the integrity check failed against the received message authentication code (MAC) as defined in Section 10.7. of RFC 6550.ro Counter32 .1.3.6.1.4.1.30982.1.2.1.8.5 |
rplReplayProtectionFailuresThe number of messages discarded because the received message Counter value is non-zero and less than the maintained incoming Counter watermark or because the received Timestamp Counter value indicates a message transmission time that is earlier than the Current time less the acceptable packet delay as defined in Section 10.7. of RFC 6550. This counter is also incremented if the temporal consistency check of the message fails as defined in Section 10.7.1.ro Counter32 .1.3.6.1.4.1.30982.1.2.1.8.6 |
rplValidParentFailuresThe number of times a packet could not be sent to a DODAG parent flagged as valid.ro Counter32 .1.3.6.1.4.1.30982.1.2.1.8.7 |
rplNoInstanceIDsThe number of times a packet could not be sent because of a missing RPLInstanceID.ro Counter32 .1.3.6.1.4.1.30982.1.2.1.8.8 |
rplTriggeredLocalRepairsThe number of times a local repair procedure was triggered.ro Counter32 .1.3.6.1.4.1.30982.1.2.1.8.9 |
rplTriggeredGlobalRepairsThe number of times a global repair procedure was triggered.ro Counter32 .1.3.6.1.4.1.30982.1.2.1.8.10 |
rplNoParentSecsThe number of seconds without a next hop (DODAG parent).ro Counter32 .1.3.6.1.4.1.30982.1.2.1.8.11 |
rplActiveNoParentSecsThe number of seconds with packets to forward without a next hop (DODAG parent).ro Counter32 .1.3.6.1.4.1.30982.1.2.1.8.12 |
rplOBitSetDownwardsNumber of packets received with the 'O' bit set from a node with a higher rank as defined in Section 18.3.2 of RFC 6550.ro Counter32 .1.3.6.1.4.1.30982.1.2.1.8.13 |
rplOBitClearedUpwardsNumber of packets received with the 'O' bit cleared from a node with a lower rank as defined in Section 18.3.2 of RFC 6550.ro Counter32 .1.3.6.1.4.1.30982.1.2.1.8.14 |
rplFBitSetNumber of packets received with the 'F' bit set as defined in Section 18.3.2 of RFC 6550.ro Counter32 .1.3.6.1.4.1.30982.1.2.1.8.15 |
rplRBitSetNumber of packets received with the 'R' bit set as defined in Section 18.3.2 of RFC 6550.ro Counter32 .1.3.6.1.4.1.30982.1.2.1.8.16 |
rplTrickleTimerResetsThe number of trickle timer resets.ro Counter32 .1.3.6.1.4.1.30982.1.2.1.8.17 |
rplMsgStatsTableBasic RPL message statistics by message type. SEQUENCE OF RplMsgStatsEntry .1.3.6.1.4.1.30982.1.2.1.9 |
rplMsgStatsEntryStatistics for a specific RPL message type. RplMsgStatsEntry .1.3.6.1.4.1.30982.1.2.1.9.1 |
rplMsgStatsTypeThe RPL message type being counted by this row. RplMessageType .1.3.6.1.4.1.30982.1.2.1.9.1.1 |
rplMsgStatsInMsgsThe number of RPL messages received of this type.ro Counter32 .1.3.6.1.4.1.30982.1.2.1.9.1.2 |
rplMsgStatsOutMsgsThe number of RPL messages sent of this type.ro Counter32 .1.3.6.1.4.1.30982.1.2.1.9.1.3 |
rplConformance OBJECT IDENTIFIER .1.3.6.1.4.1.30982.1.2.2 |
rplGroups OBJECT IDENTIFIER .1.3.6.1.4.1.30982.1.2.2.1 |
rplGeneralGroupA collection of objects providing general information about the RPL implementation. Unknown .1.3.6.1.4.1.30982.1.2.2.1.1 |
rplInstanceGroupA collection of objects providing insight into RPL Instances and RPL DODAGs. Unknown .1.3.6.1.4.1.30982.1.2.2.1.2 |
rplStatsGroupA collection of objects providing statistics about the RPL implementation. Unknown .1.3.6.1.4.1.30982.1.2.2.1.3 |
rplCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.30982.1.2.2.2 |
rplFullComplianceCompliance statement for implementations supporting read/write access, according to the object definitions. Unknown .1.3.6.1.4.1.30982.1.2.2.2.1 |
rplReadOnlyComplianceCompliance statement for implementations supporting only readonly access. Unknown .1.3.6.1.4.1.30982.1.2.2.2.2 |