INOVONICS-MODEL650-MIB
AI MIB Summary
The INOVONICS-MODEL650-MIB enables SNMP-based monitoring and management of the Inovonics Model 650 AARON FM Rebroadcast Receiver, specifically tracking device operational status, signal reception quality, and transmitter health metrics. This module facilitates the collection of performance counters and alarm states required to maintain broadcast integrity and detect hardware failures in FM rebroadcasting infrastructure.
The MIB for the Model 650 AARON FM Rebroadcast Receiver.
Main OID:
model650.1.3.6.1.4.1.42111.650
207
Objects
Active
Status
2
Dependencies
Imported Objects
Objects
207 total| Object Name |
|---|
inovonicsBroadcast OBJECT IDENTIFIER .1.3.6.1.4.1.42111 |
model650The MIB for the Model 650 AARON FM Rebroadcast Receiver. MODULE-IDENTITY .1.3.6.1.4.1.42111.650 |
traps OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.1 |
notifications OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.1.0 |
audioLossTrapThis trap occurs when the Audio Loss alarm is triggered on OR off. The status of the alarm is included as a variable binding in the form of the audioLossAlarm object. NOTIFICATION-TYPE .1.3.6.1.4.1.42111.650.1.0.1 |
lowSignalTrapThis trap occurs when the Low Signal alarm is triggered on OR off. The status of the alarm is included as a variable binding in the form of the lowSignalAlarm object. NOTIFICATION-TYPE .1.3.6.1.4.1.42111.650.1.0.2 |
rdsErrorTrapThis trap occurs when the RDS Error/Mismatch alarm is triggered on OR off. The status of the alarm is included as a variable binding in the form of the rdsErrorAlarm object. NOTIFICATION-TYPE .1.3.6.1.4.1.42111.650.1.0.3 |
pilotLossTrapThis trap occurs when the Pilot Loss alarm is triggered on OR off. The status of the alarm is included as a variable binding in the form of the pilotLossAlarm object. NOTIFICATION-TYPE .1.3.6.1.4.1.42111.650.1.0.4 |
product OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.2 |
serialSerial number.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.42111.650.2.1 |
versionCurrent firmware version.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.42111.650.2.2 |
dateDate of firmware version.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.42111.650.2.3 |
nowPlaying OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.3 |
frequencyCurrently tuned frequency, in 10kHz steps. Can be set between 6500 and 10800.rw Integer32 .1.3.6.1.4.1.42111.650.3.1 |
currentPresetCurrently selected preset. The preset can also be set to 1-10. A value of 0 means a preset is not selected.rw Integer32 .1.3.6.1.4.1.42111.650.3.2 |
antennaCurrently selected antenna. Can be set to antenna 1 or 2.rw Integer32 .1.3.6.1.4.1.42111.650.3.3 |
rssiRelative Signal Strength Indicator (RF strength). The range is 0-120dBuV.ro Integer32 .1.3.6.1.4.1.42111.650.3.4 |
bandwidthIF Bandwidth (units: kHz).ro Integer32 .1.3.6.1.4.1.42111.650.3.5 |
multipathAmount of Multipath. The Range is 0-100%.ro Integer32 .1.3.6.1.4.1.42111.650.3.6 |
noiseAmount of Ultrasonic Noise. The Range is 0-100%.ro Integer32 .1.3.6.1.4.1.42111.650.3.7 |
leftLeveldBLeft channel level (units: dB).ro Integer32 (-128..6) .1.3.6.1.4.1.42111.650.3.8 |
rightLeveldBRight channel level (units: dB).ro Integer32 (-128..6) .1.3.6.1.4.1.42111.650.3.9 |
leftPlusRightLeveldBLeft+Right level (units: dB).ro Integer32 (-128..6) .1.3.6.1.4.1.42111.650.3.10 |
leftMinusRightLeveldBLeft-Right level (units: dB).ro Integer32 (-128..6) .1.3.6.1.4.1.42111.650.3.11 |
statusThis describes the current status, such as if everything is normal or if a backup source is in use.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.42111.650.3.12 |
receptionTools OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.4 |
bandwidthIF OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.4.1 |
bandwidthModeIF Bandwidth Mode - set to automatically adjust IF bandwidth, or used a fixed bandwidth set by the fixedBandwidth OID.rw Enumeration .1.3.6.1.4.1.42111.650.4.1.1 |
fixedBandwidthIF Bandwidth used when the mode is set to fixed.rw Enumeration .1.3.6.1.4.1.42111.650.4.1.2 |
stereoBlend OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.4.2 |
stereoBlendAmountAmount of stereo blend processing applied (Units: %).ro Integer32 .1.3.6.1.4.1.42111.650.4.2.1 |
stereoBlendAutoIf set to auto, the blend processing is handled automatically. the other stereo blend settings are not used.rw OnOff .1.3.6.1.4.1.42111.650.4.2.2 |
stereoBlendUseRSSISet ON to use RSSI as a metric for blend processing.rw OnOff .1.3.6.1.4.1.42111.650.4.2.3 |
stereoBlendThresholdRSSIAs the RSSI drops below this set value, more blending will occur (Units: dBuV).rw Integer32 .1.3.6.1.4.1.42111.650.4.2.4 |
stereoBlendUseUSNSet ON to use USN as a metric for blend processing.rw OnOff .1.3.6.1.4.1.42111.650.4.2.5 |
stereoBlendThresholdUSNAs the USN goes above this set value, more blending will occur (Units: %).rw Integer32 .1.3.6.1.4.1.42111.650.4.2.6 |
stereoBlendUseMultipathSet ON to use multipath as a metric for blend processing.rw OnOff .1.3.6.1.4.1.42111.650.4.2.7 |
stereoBlendThresholdMultipathAs the multipath goes above this set value, more blending will occur (Units: %).rw Integer32 .1.3.6.1.4.1.42111.650.4.2.8 |
highBlend OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.4.3 |
highBlendAmountAmount of stereo blend processing applied (Units: %).ro Integer32 .1.3.6.1.4.1.42111.650.4.3.1 |
highBlendAutoIf set to auto, the high blend processing is handled automatically. the other high blend settings are not used.rw OnOff .1.3.6.1.4.1.42111.650.4.3.2 |
highBlendUseRSSISet ON to use RSSI as a metric for high blend processing.rw OnOff .1.3.6.1.4.1.42111.650.4.3.3 |
highBlendThresholdRSSIAs the RSSI drops below this set value, more high blending will occur (Units: dBuV).rw Integer32 .1.3.6.1.4.1.42111.650.4.3.4 |
highBlendUseUSNSet ON to use USN as a metric for high blend processing.rw OnOff .1.3.6.1.4.1.42111.650.4.3.5 |
highBlendThresholdUSNAs the USN goes above this set value, more high blending will occur (Units: %).rw Integer32 .1.3.6.1.4.1.42111.650.4.3.6 |
highBlendUseMultipathSet ON to use multipath as a metric for high blend processing.rw OnOff .1.3.6.1.4.1.42111.650.4.3.7 |
highBlendThresholdMultipathAs the multipath goes above this set value, more high blending will occur (Units: %).rw Integer32 .1.3.6.1.4.1.42111.650.4.3.8 |
bandBlend OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.4.4 |
bandBlendEnableEnable or disable 4 band blend processing.rw OnOff .1.3.6.1.4.1.42111.650.4.4.1 |
bandBlendControlControls the agressiveness of the 4 band blend.rw Integer32 .1.3.6.1.4.1.42111.650.4.4.2 |
bandBlendLFThe amount of blending in the Low Frequency band (Units: %).ro Integer32 .1.3.6.1.4.1.42111.650.4.4.3 |
bandBlend2kThe amount of blending in the 2kHz band (Units: %).ro Integer32 .1.3.6.1.4.1.42111.650.4.4.4 |
bandBlend5kThe amount of blending in the 5kHz band (Units: %).ro Integer32 .1.3.6.1.4.1.42111.650.4.4.5 |
bandBlendHFThe amount of blending in the High Frequency band (Units: %).ro Integer32 .1.3.6.1.4.1.42111.650.4.4.6 |
highcut OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.4.5 |
highcutAmountAmount of highcut processing applied (Units: %).ro Integer32 .1.3.6.1.4.1.42111.650.4.5.1 |
highcutAutoIf set to auto, the highcut processing is handled automatically. the other high blend settings are not used.rw OnOff .1.3.6.1.4.1.42111.650.4.5.2 |
highcutUseRSSISet ON to use RSSI as a metric for highcut processing.rw OnOff .1.3.6.1.4.1.42111.650.4.5.3 |
highcutThresholdRSSIAs the RSSI drops below this set value, more highcut will occur (Units: dBuV).rw Integer32 .1.3.6.1.4.1.42111.650.4.5.4 |
highcutUseUSNSet ON to use USN as a metric for highcut processing.rw OnOff .1.3.6.1.4.1.42111.650.4.5.5 |
highcutThresholdUSNAs the USN goes above this set value, more highcut will occur (Units: %).rw Integer32 .1.3.6.1.4.1.42111.650.4.5.6 |
highcutUseMultipathSet ON to use multipath as a metric for highcut processing.rw OnOff .1.3.6.1.4.1.42111.650.4.5.7 |
highcutThresholdMultipathAs the multipath goes above this set value, more highcut will occur (Units: %).rw Integer32 .1.3.6.1.4.1.42111.650.4.5.8 |
monoStereoSet to forced mono or stereo (auto).rw Enumeration .1.3.6.1.4.1.42111.650.4.6 |
multipathSuppressionControls the use of Multipath Suppression processing.rw OnOff .1.3.6.1.4.1.42111.650.4.7 |
channelEqualizerControls the use of the Channel Equalizer.rw OnOff .1.3.6.1.4.1.42111.650.4.8 |
rds OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.5 |
piPI (Program Identification) Code.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.42111.650.5.1 |
callCallsign/Call Letters for the received PI Code.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.42111.650.5.2 |
psPS (Program Service).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.42111.650.5.3 |
rtRT (Radio Text).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.42111.650.5.4 |
ptyPTY (Program Type).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.42111.650.5.5 |
ptynPTYN (Program Type Name).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.42111.650.5.6 |
rdsTimeRDS time received.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.42111.650.5.7 |
msMusic/Speech flag.ro Enumeration .1.3.6.1.4.1.42111.650.5.8 |
diMono/Stereo flag.ro Enumeration .1.3.6.1.4.1.42111.650.5.9 |
tpTraffic Programming flag.ro Enumeration .1.3.6.1.4.1.42111.650.5.10 |
taTraffic Alert flag.ro OnOff .1.3.6.1.4.1.42111.650.5.11 |
alarms OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.6 |
alarmStatus OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.6.1 |
audioLossAlarmStatus of the Audio Loss alarm.ro OnOff .1.3.6.1.4.1.42111.650.6.1.1 |
lowSignalAlarmStatus of the Low Signal alarm.ro OnOff .1.3.6.1.4.1.42111.650.6.1.2 |
rdsErrorAlarmStatus of the RDS Error/Mismatch alarm.ro OnOff .1.3.6.1.4.1.42111.650.6.1.3 |
pilotLossAlarmStatus of the Pilot Loss alarm.ro OnOff .1.3.6.1.4.1.42111.650.6.1.4 |
audioLoss OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.6.2 |
audioLossEnableEnable the Audio Loss alarm.rw OnOff .1.3.6.1.4.1.42111.650.6.2.1 |
audioLossThreshOnThreshold for alarm turning on (units: dB).rw Integer32 (-40..0) .1.3.6.1.4.1.42111.650.6.2.2 |
audioLossThreshOffThreshold for alarm turning off (units: dB).rw Integer32 (-40..0) .1.3.6.1.4.1.42111.650.6.2.3 |
audioLossTimeOnAmount of time the audio level must be below the Threshold On value before the alarm turns on (units: seconds).rw Integer32 .1.3.6.1.4.1.42111.650.6.2.4 |
audioLossTimeOffAmount of time the audio level must be above the Threshold On value before the alarm turns off (units: seconds).rw Integer32 .1.3.6.1.4.1.42111.650.6.2.5 |
lowSignal OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.6.3 |
lowSignalEnableEnable the Low Signal alarm.rw OnOff .1.3.6.1.4.1.42111.650.6.3.1 |
lowSignalMuteIf enabled, radio will mute when Low Signal alarm is on.rw OnOff .1.3.6.1.4.1.42111.650.6.3.2 |
lowSignalThreshOnThreshold for alarm turning on (units: dBuV).rw Integer32 .1.3.6.1.4.1.42111.650.6.3.3 |
lowSignalThreshOffThreshold for alarm turning off (units: dBuV).rw Integer32 .1.3.6.1.4.1.42111.650.6.3.4 |
lowSignalTimeOnAmount of time the RSSI level must be below the Threshold On value before the alarm turns on (units: seconds).rw Integer32 .1.3.6.1.4.1.42111.650.6.3.5 |
lowSignalTimeOffAmount of time the RSSI level must be above the Threshold Off value before the alarm turns off (units: seconds).rw Integer32 .1.3.6.1.4.1.42111.650.6.3.6 |
rdsLoss OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.6.4 |
rdsLossEnableEnable the RDS Error alarm.rw OnOff .1.3.6.1.4.1.42111.650.6.4.1 |
rdsPIErrorEnableIf enabled, the alarm will occur if RDS is present but the received PI does not match that set in rdsPICode.rw OnOff .1.3.6.1.4.1.42111.650.6.4.2 |
rdsPICodeSet PI Code to compare with received PI.rw DisplayString .1.3.6.1.4.1.42111.650.6.4.3 |
rdsLossTimeOnAmount of time the RDS must be gone/PI Code incorrect before the alarm turns on (units: seconds).rw Integer32 .1.3.6.1.4.1.42111.650.6.4.4 |
rdsLossTimeOffAmount of time the RDS must be present/PI Code correct before the alarm turns off (units: seconds).rw Integer32 .1.3.6.1.4.1.42111.650.6.4.5 |
pilotLoss OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.6.5 |
pilotLossEnableEnable the Pilot Loss alarm.rw OnOff .1.3.6.1.4.1.42111.650.6.5.1 |
pilotLossTimeOnAmount of time the pilot must be gone before the alarm turns on (units: seconds).rw Integer32 .1.3.6.1.4.1.42111.650.6.5.2 |
pilotLossTimeOffAmount of time the pilot must be present before the alarm turns off (units: seconds).rw Integer32 .1.3.6.1.4.1.42111.650.6.5.3 |
audioFailover OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.6.6 |
failoverAudioAudio Failover to backup source will occur when there is an Audio Loss alarm.rw OnOff .1.3.6.1.4.1.42111.650.6.6.1 |
failoverRSSIAudio Failover to backup source will occur when there is a Low Signal alarm.rw OnOff .1.3.6.1.4.1.42111.650.6.6.2 |
failoverRDSAudio Failover to backup source will occur when there is a RDS alarm.rw OnOff .1.3.6.1.4.1.42111.650.6.6.3 |
failoverSourceThe backup audio source to use when the failover is triggered.rw Enumeration .1.3.6.1.4.1.42111.650.6.6.4 |
failoverStreamURLThe URL for the backup stream.rw DisplayString .1.3.6.1.4.1.42111.650.6.6.5 |
stereoRegen OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.7 |
regenModeSet to off (Composite Pass-Through) or on (Composite Regen).rw OnOff .1.3.6.1.4.1.42111.650.7.1 |
regenPilot OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.7.2 |
regenPilotEnableTurn the pilot on/off when in regen mode.rw OnOff .1.3.6.1.4.1.42111.650.7.2.1 |
regenPilotInjectionThe pilot injection level when in regen mode (Units: 0.1%, Ex: 90 = 9.0%).rw Integer32 .1.3.6.1.4.1.42111.650.7.2.2 |
regenRDS OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.7.3 |
regenRDSEnableTurn RDS on/off when in regen mode.rw OnOff .1.3.6.1.4.1.42111.650.7.3.1 |
regenRDSInjectionThe RDS injection level when in regen mode (Units: 0.1%, Ex: 50 = 5.0%).rw Integer32 .1.3.6.1.4.1.42111.650.7.3.2 |
regenRDSModeSets how the RDS should be regenerated.rw Enumeration .1.3.6.1.4.1.42111.650.7.3.3 |
builtInScrollSpeedSets how quickly the PS field will scroll with the built-in RDS. Higher values can cause jumbled characters on some radios.rw Integer32 .1.3.6.1.4.1.42111.650.7.3.4 |
builtInPIBuilt-in RDS PI Code (also used for re-encode with new PI mode).rw DisplayString .1.3.6.1.4.1.42111.650.7.3.5 |
builtInPSBuilt-in RDS PS text. The RDS encoder will automatically parse longer messages.rw DisplayString .1.3.6.1.4.1.42111.650.7.3.6 |
builtInRTBuilt-in RDS Radio Text.rw DisplayString .1.3.6.1.4.1.42111.650.7.3.7 |
builtInPTYBuilt-in RDS Program Type.rw Integer32 .1.3.6.1.4.1.42111.650.7.3.8 |
builtInMSBuilt-in RDS Music/Speed flag.rw Enumeration .1.3.6.1.4.1.42111.650.7.3.9 |
builtInDIBuilt-in RDS stereo/mono flag.rw Enumeration .1.3.6.1.4.1.42111.650.7.3.10 |
builtInTPBuilt-in RDS Traffic Programming flag.rw OnOff .1.3.6.1.4.1.42111.650.7.3.11 |
setup OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.8 |
outputs OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.8.1 |
analogLevelAnalog Output level (Units: 0.1dB, Ex. -100 = -10.0dB).rw Integer32 (-200..180) .1.3.6.1.4.1.42111.650.8.1.1 |
analogDeemphasisDe-emphasis applied to analog outputs.rw OnOff .1.3.6.1.4.1.42111.650.8.1.2 |
digitalLevelDigital Output level (Units: 0.1dB, Ex. -200 = -20.0dB).rw Integer32 (-300..0) .1.3.6.1.4.1.42111.650.8.1.3 |
digitalDeemphasisDe-emphasis applied to AES output.rw OnOff .1.3.6.1.4.1.42111.650.8.1.4 |
digitalSamplerateSample Rate of the AES output.rw Enumeration .1.3.6.1.4.1.42111.650.8.1.5 |
mpx1LevelMPX1 Output level (Units: mVpp, Ex. 3100 = 3.10Vpp). Though the units are mVpp, the resolution is less than 1mVpp. When this value is set, it will round to the closest possible value.rw Integer32 .1.3.6.1.4.1.42111.650.8.1.6 |
mpx2LevelMPX2 Output level (Units: mVpp, Ex. 3100 = 3.10Vpp). Though the units are mVpp, the resolution is less than 1mVpp. When this value is set, it will round to the closest possible value.rw Integer32 .1.3.6.1.4.1.42111.650.8.1.7 |
mpxClippingMPX Clipping amount (Units: 0.1dB, Ex. 16 = 1.6dB. This can be set in 0.2dB steps.rw Integer32 (-20..30) .1.3.6.1.4.1.42111.650.8.1.8 |
network OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.8.2 |
dhcpDHCP enabled, or disabled (static IP).rw Enumeration .1.3.6.1.4.1.42111.650.8.2.1 |
ipDevice IP Address.rw IpAddress .1.3.6.1.4.1.42111.650.8.2.2 |
gatewayGateway IP Address.rw IpAddress .1.3.6.1.4.1.42111.650.8.2.3 |
subnetDevice subnet mask.rw IpAddress .1.3.6.1.4.1.42111.650.8.2.4 |
dnsDevice DNS address.rw IpAddress .1.3.6.1.4.1.42111.650.8.2.5 |
httpPortHTTP port for webserver.rw Integer32 .1.3.6.1.4.1.42111.650.8.2.6 |
hostnameNBNS hostname.rw DisplayString .1.3.6.1.4.1.42111.650.8.2.7 |
macMAC address of this device.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.42111.650.8.2.8 |
dynDNS OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.8.3 |
ddnsModeDynamic DNS provider/mode.rw Enumeration .1.3.6.1.4.1.42111.650.8.3.1 |
ddnsHostnameYour DDNS hostname (proper web addess).rw DisplayString .1.3.6.1.4.1.42111.650.8.3.2 |
ddnsUsernameThe username for your DDNS account.rw DisplayString .1.3.6.1.4.1.42111.650.8.3.3 |
ddnsPasswordThe password for your DDNS account.rw DisplayString .1.3.6.1.4.1.42111.650.8.3.4 |
ddnsStatusThe status of the DDNS service.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.42111.650.8.3.5 |
time OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.8.4 |
timezoneUTC offset (Units: 0.1hours). EX: -80 = UTC-8.0. Can be set in 0.5 hour increments.rw Integer32 (-120..140) .1.3.6.1.4.1.42111.650.8.4.1 |
dstWhether Daylight Saving Time is currently in effect.rw OnOff .1.3.6.1.4.1.42111.650.8.4.2 |
autodstEnable to automatically follow US Daylight Saving Time.rw OnOff .1.3.6.1.4.1.42111.650.8.4.3 |
timeServerURL for a custom NTP time server.rw DisplayString .1.3.6.1.4.1.42111.650.8.4.4 |
snmp OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.8.5 |
snmpModeSNMP mode. Restrict SNMP read or write.rw Enumeration .1.3.6.1.4.1.42111.650.8.5.1 |
snmpReadCommunitySNMP read community string for read access.rw DisplayString .1.3.6.1.4.1.42111.650.8.5.2 |
snmpWriteCommunitySNMP write community string for write access.rw DisplayString .1.3.6.1.4.1.42111.650.8.5.3 |
snmpPortUDP port for SNMP communication. SNMP standard is UDP port 161.rw Integer32 .1.3.6.1.4.1.42111.650.8.5.4 |
snmpTrapsPortUDP port for SNMP traps. SNMP standard is UDP port 162.rw Integer32 .1.3.6.1.4.1.42111.650.8.5.5 |
snmpTrapDestination1IP address 1 to send traps to.rw IpAddress .1.3.6.1.4.1.42111.650.8.5.6 |
snmpTrapDestination2IP address 2 to send traps to.rw IpAddress .1.3.6.1.4.1.42111.650.8.5.7 |
snmpTrapDestination3IP address 3 to send traps to.rw IpAddress .1.3.6.1.4.1.42111.650.8.5.8 |
email OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.8.6 |
smtpServerURL or IP of SMTP server.rw DisplayString .1.3.6.1.4.1.42111.650.8.6.1 |
smtpPortTCP port for SMTP (depends on server).rw Integer32 .1.3.6.1.4.1.42111.650.8.6.2 |
sslEnable/disable SSL security for connection to SMTP server.rw OnOff .1.3.6.1.4.1.42111.650.8.6.3 |
emailFromThis will show as the 'From' when you receive emails from this unit.rw DisplayString .1.3.6.1.4.1.42111.650.8.6.4 |
emailUsernameThe email address to send from.rw DisplayString .1.3.6.1.4.1.42111.650.8.6.5 |
emailPasswordThe password to the email address to send from.rw DisplayString .1.3.6.1.4.1.42111.650.8.6.6 |
recipientTableTable of 10 email recipients. SEQUENCE OF RecipientEntry .1.3.6.1.4.1.42111.650.8.6.7 |
recipientEntrySingle recipient entry. RecipientEntry .1.3.6.1.4.1.42111.650.8.6.7.1 |
recipientIndexIndex of recipient (recipients 1 through 10). Integer32 .1.3.6.1.4.1.42111.650.8.6.7.1.1 |
emailAddressEmail address for the recipient of email notifications.rw DisplayString .1.3.6.1.4.1.42111.650.8.6.7.1.2 |
audioLossEmailThis recipient will receive Audio Loss emails.rw OnOff .1.3.6.1.4.1.42111.650.8.6.7.1.3 |
lowSignalEmailThis recipient will receive Low Signal emails.rw OnOff .1.3.6.1.4.1.42111.650.8.6.7.1.4 |
rdsLossEmailThis recipient will receive RDS Loss emails.rw OnOff .1.3.6.1.4.1.42111.650.8.6.7.1.5 |
pilotLossEmailThis recipient will receive Pilot Loss emails.rw OnOff .1.3.6.1.4.1.42111.650.8.6.7.1.6 |
dailyLogEmailThis recipient will receive daily log emails.rw OnOff .1.3.6.1.4.1.42111.650.8.6.7.1.7 |
weeklyLogEmailThis recipient will receive weekly log emails.rw OnOff .1.3.6.1.4.1.42111.650.8.6.7.1.8 |
monthlyLogEmailThis recipient will receive monthly log emails.rw OnOff .1.3.6.1.4.1.42111.650.8.6.7.1.9 |
alarmLog OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.8.7 |
alarmLogStatusFullness of alarm log (units: %). Set to 0 to clear the alarm log.rw Integer32 .1.3.6.1.4.1.42111.650.8.7.1 |
alarmLogFullEmailSend an email reminder when the log is (%) full.rw Integer32 .1.3.6.1.4.1.42111.650.8.7.2 |
alarmPolarity OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.8.8 |
audioLossPolarityPolarity of the Audio Loss alarm output.rw Enumeration .1.3.6.1.4.1.42111.650.8.8.1 |
lowSignalPolarityPolarity of the Low Signal alarm output.rw Enumeration .1.3.6.1.4.1.42111.650.8.8.2 |
rdsLossPolarityPolarity of the RDS Loss alarm output.rw Enumeration .1.3.6.1.4.1.42111.650.8.8.3 |
pilotLossPolarityPolarity of the Pilot Loss alarm output.rw Enumeration .1.3.6.1.4.1.42111.650.8.8.4 |
region OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.8.9 |
tuningStepsThe step size used when tuning from the front panel and web.rw Enumeration .1.3.6.1.4.1.42111.650.8.9.1 |
deemphasisSet deemphasis to 50us or 75us.rw Enumeration .1.3.6.1.4.1.42111.650.8.9.2 |
rdsDecodeModeSet RDS decoding mode to RDS (Europe) or RBDS (North America).rw Enumeration .1.3.6.1.4.1.42111.650.8.9.3 |
testOscillator OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.8.10 |
oscModeEnable/disable the internal tone generator for testing purposes.rw Enumeration .1.3.6.1.4.1.42111.650.8.10.1 |
oscFrequencyFrequency of the test oscillator (Units: Hz). Can be set in multiples of 10Hz.rw Integer32 .1.3.6.1.4.1.42111.650.8.10.2 |
oscLevelLevel of the test oscillator (Units: dB).rw Integer32 (-30..0) .1.3.6.1.4.1.42111.650.8.10.3 |
serialPortBaudRateEnable/disable the internal tone generator for testing purposes.rw Enumeration .1.3.6.1.4.1.42111.650.8.11 |
passwords OBJECT IDENTIFIER .1.3.6.1.4.1.42111.650.9 |
frontPanelPasswordThe password for restricting front panel access.rw DisplayString .1.3.6.1.4.1.42111.650.9.1 |
webpagesPasswordThe password for restricting webpage access.rw DisplayString .1.3.6.1.4.1.42111.650.9.2 |