FLOWPOINT-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
136
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
136 total| Object Name |
|---|
flowpoint OBJECT IDENTIFIER .1.3.6.1.4.1.1548 |
RFC1213-MIB Unknown .1.3.6.1.4.1.1548 |
fpdod OBJECT IDENTIFIER .1.3.6.1.4.1.1548.1 |
dodTableThe DOD basic configuration table for each remote
connection. All of the DOD tables are indexed
(identified) by DestinationName. SEQUENCE OF DodEntry .1.3.6.1.4.1.1548.1.1 |
dodEntry DodEntry .1.3.6.1.4.1.1548.1.1.1 |
dodTableIDThe identifier number of this remote name. Each dod
table will have a unique identifier number for it.
The ID number is issued when the dod table of the
destination name is created on the agent side.
This object is obsoleted: use dodDestinationName
as the index.roobsolete INTEGER .1.3.6.1.4.1.1548.1.1.1.1 |
dodDestinationNameA textual description of the remote destination. The
name is given by the manager side when the manager uses
object dodTableOperation to create a new Dod record.
The dodDestination is important. It will be used
throughout all of the Dod database as index to
access each object.ro DisplayString .1.3.6.1.4.1.1548.1.1.1.2 |
dodPasswordThe password for this remote connection. It is used to
check the remote's password when the remote client or
server dials in. It is also used when authentication
is enabled during outgoing calls. GENERR is returned
if not authorized to read the dodPassword.rw DisplayString .1.3.6.1.4.1.1548.1.1.1.3 |
dodAuthenProtocolThe minimum authentication protocol this remote
connection is using. It is one of CHAP or PAP
or NONE. The actual authentication phase can be
performed with a better protocol than specified here:
for instance if set to PAP and the remote supports
CHAP (as negotiated during the LCP phase), CHAP
authentication will be performed. None means that
authentication of this remote is disabled during
outgoing calls. All incoming calls are ALWAYS
authenticated, so setting this to none prevents
from accepting incoming calls.rw AuthenProtoType .1.3.6.1.4.1.1548.1.1.1.4 |
dodMaxLinksThe maximum number of links to be used when
the system dials out or accepts incoming calls.
Should be 1 or 2 for BRI lines.rw INTEGER .1.3.6.1.4.1.1548.1.1.1.5 |
dodBWThresholdThe threshold of bandwidth utilization of established
links used to trigger an additional call, expressed as
an integer percentage, i.e. 0 to 100. 0 means that
all available links are dialed at once while 100
means that no additional links are used. The type
of bandwidth measured by this object is defined by
dodBODType.rw INTEGER .1.3.6.1.4.1.1548.1.1.1.6 |
dodPreferTypeThe preferred line connection type.rw ConnectionType .1.3.6.1.4.1.1548.1.1.1.7 |
dodTearDownTimerThe timeout limit to tear down the link when there is
no activity for the link, expressed in seconds.rw INTEGER .1.3.6.1.4.1.1548.1.1.1.8 |
dodSourceIPAddressThe local IP address of the WAN port. It is used to
negotiate with the remote side when dialing in or out.
When nonzero, it overrides the default address,
coming from the LAN port IP address (ethernet).rw IpAddress .1.3.6.1.4.1.1548.1.1.1.9 |
dodRemoteIPAddressThe remote IP address of the WAN port, if needed.
Set to 0 otherwise.rw IpAddress .1.3.6.1.4.1.1548.1.1.1.10 |
dodSourceIPMaskThe local IP net mask of the WAN port. It is used
with dodSourceIPAddress.rw IpAddress .1.3.6.1.4.1.1548.1.1.1.11 |
dodRemoteIPMaskThe remote side IP network mask.rw IpAddress .1.3.6.1.4.1.1548.1.1.1.12 |
dodIPXNetAddressThe IPX network address associated with the WAN link
when connected to this remote.rw IpxNetAddress .1.3.6.1.4.1.1548.1.1.1.13 |
dodIPFiltersNumber of IP filters currently defined for this remote.ro Counter .1.3.6.1.4.1.1548.1.1.1.14 |
dodIPXFiltersNumber of IPX filters currently defined for this remotero Counter .1.3.6.1.4.1.1548.1.1.1.15 |
dodRemoteIPNetsThis object describes the number of static IP routing
entries for this destination name or connection. The
static IP routing table is defined in another group.ro Counter .1.3.6.1.4.1.1548.1.1.1.16 |
dodRemoteIPXNetsThis object describes the number of static IPX routing
entries for this destination. The static IPX routing
table is defined in another group.ro Counter .1.3.6.1.4.1.1548.1.1.1.17 |
dodRemoteIPXSAPsThis object describes the number of static IPX SAP
entries for this destination. The static IPX SAP
table is defined in another group.ro Counter .1.3.6.1.4.1.1548.1.1.1.18 |
dodRemoteMacStateThis object controls the current bridge state (enabled
or disabled) for this destination.
When one of the remote destinations is turned on, the
LAN port (ethernet) bridge capability will be turned
on also, after a reboot. If this destination's bridge
state is disabled and the bridge state of all the other
destinations is also disabled, the LAN port bridge
state will be disabled. Otherwise, if another
destination's bridge state is still enabled, the LAN
port bridge state will stay enabled. This mechanism
is implemented in the system.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.19 |
dodRemoteMacsThe number of specific MAC addresses defined to be
statically bridged to this remote.ro Counter .1.3.6.1.4.1.1548.1.1.1.20 |
dodLastActivityTimeThe last activity time with this destinationro INTEGER .1.3.6.1.4.1.1548.1.1.1.21 |
dodTableOperationThis object is used to create a new DOD record or
to delete a DOD record.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.22 |
dodMinLinksThe minimum number of links to be used when
the system dials out or accepts incoming calls.
Must be lower or equal to dodMaxLinks.rw INTEGER .1.3.6.1.4.1.1548.1.1.1.23 |
dodBODTypeThe type of traffic to which bandwidth measurement
(defined by dodBWThreshold) applies.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.24 |
dodIpOptRecvRIPAllows processing of RIP packets received from this
destination, when connected and IP routing is enabled
in a RIP 1 compatible manner.
dodIpOptRecvRIP, dodIpOptRecvRIP1, and dodIpOptRecvRIP2
are mutually exclusive.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.25 |
dodIpOptSendRIPAllows sending of RIP packets to this destination
when connected and IP routing is enabled in a
RIP 1 compatible manner.
dodIpOptSendRIP, dodIpOptSendRIP1, and dodIpOptSendRIP2
are mutually exclusive.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.26 |
dodIpOptRecvRIPDefaultAllows updating of the IP default route when
receiving a RIP packet from this destination
for the route 0.0.0.0.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.27 |
dodIpOptSendRIPDefaultAllows sending of the IP default route (if known) to
this destination when connected, as 0.0.0.0.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.28 |
dodIpOptKeepPrivateAllows to keep the route to this destination
private, i.e. don't advertise it to other destinationsrw Enumeration .1.3.6.1.4.1.1548.1.1.1.29 |
dodBrOptUseStpAllows use of Bridging Spanning Tree Protocol when
connected to this destination (causes a 40 second
startup delay): use when topology loops are likely.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.30 |
dodPPPOptUseLCPEchoPerform a PPP LCP Echo request at regular intervals
when connected to this destination.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.31 |
dodEntryIsDisabledThis database entry is active (enabled) or temporarily
disabled (i.e. bypassed when searching the database).
This eliminates the need for constant add/removes.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.32 |
dodCallbackOptionThis option defines under what circumstances this system
is allowed to dial the specified remote. The setting
'enable' means that this system is free to call the
specified remote on its own and also to dial it back.
Under the 'disable' setting, dialing back is never a
possibility, but this system can dial the remote on its
own if a phone number exists for it. The 'callback-only'
setting prevents this system from calling the remote
on its own: it will only perform the dial-back service.
Note: in order to implement dial-back, Caller entries
for this remote must exist (in dodCallerTable).
This allows this system to identify what remote
is calling, locating its database information
and possibly calling it back. Caller Id verification
(in fpSysCallerIdTable) is independent but uses
the same dodCallerTable information.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.33 |
dodSendDataAsVoiceThis option determines whether ISDN data calls issued to
this remote should be generated as voice calls instead
of restricted or unrestricted digital (ISDN only).rw Enumeration .1.3.6.1.4.1.1548.1.1.1.34 |
dodIPXNetStrAddressThe IPX network address associated with the WAN link
when connected to this remote. This is an alternative
to the dodIPXNetAddress object to be used when OCTET
STRINGs are not implemented. In this case, specify the
IPX network number as an ASCII string containing from
1 to 8 characters, to be converted to hexadecimal by
the firmware.rw DisplayString .1.3.6.1.4.1.1548.1.1.1.35 |
dodOurSystemNameOur system name (also called user name) when initiating
a communication with this remote. It is used to override
the global system name (fpSysName) and is useful when the
name was assigned by the remote system admin, not
by this system admin, in order to avoid using the same
name (not under our control) for all connections.rw DisplayString .1.3.6.1.4.1.1548.1.1.1.36 |
dodOurPasswordOur system password when initiating a communication
with this remote. It is used to override the global
system password (when not empty) and is useful when the
password was assigned by the remote system admin, not
by this system admin, in order to avoid using the same
password (not under our control) for all connections.
GENERR is returned if not authorized to read the
dodOurPassword.rw DisplayString .1.3.6.1.4.1.1548.1.1.1.37 |
dodPPPCallbackOptionThis option defines under what circumstances this system
is requesting a callback by using a method within the PPP
protocol suite (as opposed to an ISDN callback). The
possibilities are:
- don't do any PPP callback (none)
- ask the peer to us back based on the database record
that he has for us (authentication).
- supply the string (i.e. phone number, including prefixes
etc,...) that the peer should use to call us back.
- supply a location information which the peer will use
in addition to our user name to call us back.
- supply a E.164 string to the peer to call us back.
- supply a generic string (name-string) to the peer so
that it can use to it call us back using whatever
method it deems appropriate. This router will force
this to be the same as the remote name (index in the
remote database) if it receives such a string.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.38 |
dodPPPCallbackInfoWhen the dodPPPCallbackOption is set to something
other than none(1), this fields contains the additional
information sent to the PPP peer when requested a
callback.rw DisplayString .1.3.6.1.4.1.1548.1.1.1.39 |
dodDontAuthenticateWhen enabled (1), do not request any authentication
protocol when dialing out this destination. Note that
an incoming call from this remote still requires some
form of authentication (to find this remote entry record),
as the key to the record is the authenticated name.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.40 |
dodIPAddressTranslationWhen enabled (1), do IP address translation for traffic
to/from this remote.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.41 |
dodIpOptRecvRIP1Allows processing of RIP packets received from this
destination, when connected and IP routing is enabled
using RIP 1 only.
dodIpOptRecvRIP, dodIpOptRecvRIP1, and dodIpOptRecvRIP2
are mutually exclusive.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.42 |
dodIpOptSendRIP1Allows sending of RIP packets to this destination
when connected and IP routing is enabled using RIP 1 only.
dodIpOptSendRIP, dodIpOptSendRIP1, and dodIpOptSendRIP2
are mutually exclusive.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.43 |
dodIpOptRecvRIP2Allows processing of RIP packets received from this
destination, when connected and IP routing is enabled
using RIP 2 only.
dodIpOptRecvRIP, dodIpOptRecvRIP1, and dodIpOptRecvRIP2
are mutually exclusive.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.44 |
dodIpOptSendRIP2Allows sending of RIP packets to this destination
when connected and IP routing is enabled using RIP 2 only.
dodIpOptSendRIP, dodIpOptSendRIP1, and dodIpOptSendRIP2
are mutually exclusive.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.45 |
dodProtocolType of protocol used for communicating with this remote.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.46 |
dodCompressionWhen enabled (1), do compression for traffic
to/from this remote.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.47 |
dodPasswordSpecifiedReturn true if the password for this remote connection
has been specified.ro Enumeration .1.3.6.1.4.1.1548.1.1.1.48 |
dodOurPasswordSpecifiedReturn true if our system password for this
remote connnection has been specified.ro Enumeration .1.3.6.1.4.1.1548.1.1.1.49 |
dodBlockNetBIOSWhen enabled (1), block NetBIOS traffic
to this remote.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.50 |
dodMtuWhen non-zero, the desired MTU size for this remote.
When zero, use the default MTU size for the interface.
The MTU size used is the minimum of the desired MTU size
for this remote and the maximum MTU size allowed for
the interface.rw INTEGER .1.3.6.1.4.1.1548.1.1.1.51 |
dodIpSlaveModeWhen enabled (1), always accept peer proposal for our
IP address for our WAN interface.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.52 |
dodReacquireIpAddrWhen enabled (1), try to reacquire the last used
IP address for this interface IF we believe any
TCP connections are still active to this remote.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.53 |
dodIpxOptRIPSAPWhen enabled (1), allows IPXCP to negotiate the use of
RIP and SAP IPX traffic. Actual use of the RIP and SAP
protocols will depend on the capabilities of the remote
at the time the PPP connection is established.rw Enumeration .1.3.6.1.4.1.1548.1.1.1.54 |
dodCallIDTableA list of Call identifiers (phone number, DLCI ....)
for a particular destination name and link type (ISDN).
This table includes only two entries, type and phone
number count. SEQUENCE OF DodCallIDEntry .1.3.6.1.4.1.1548.1.2 |
dodCallIDEntryAn entry of Call identifier for each connection type. DodCallIDEntry .1.3.6.1.4.1.1548.1.2.1 |
dodCallIDTypeThe connection type.ro ConnectionType .1.3.6.1.4.1.1548.1.2.1.1 |
dodCallIDPhonesNumber of entries in the dodPhoneTable for this
type of connection and this remote.ro Counter .1.3.6.1.4.1.1548.1.2.1.2 |
dodPhoneTable SEQUENCE OF DodPhoneEntry .1.3.6.1.4.1.1548.1.3 |
dodPhoneEntry DodPhoneEntry .1.3.6.1.4.1.1548.1.3.1 |
dodPhoneIndexIt is an index to recognize which phone number
is in the table with the specified CallIDType and
DestinationName.ro INTEGER .1.3.6.1.4.1.1548.1.3.1.1 |
dodPhoneSpeedThe line speed (in bits per seconds) for asynchronous
connections.rw INTEGER .1.3.6.1.4.1.1548.1.3.1.2 |
dodPhoneNumberThe phone number string.rw DisplayString .1.3.6.1.4.1.1548.1.3.1.3 |
dodRemoteMacTableA table of MAC addresses for bridging of the
specified destination name. The table is indexed
by destination name and MAC address. SEQUENCE OF DodRemoteMacEntry .1.3.6.1.4.1.1548.1.4 |
dodRemoteMacEntry DodRemoteMacEntry .1.3.6.1.4.1.1548.1.4.1 |
dodRemoteMacIndexThe index number is not used currently.
User don't need to implement it currently.
The table is indexed by the MAC address.roobsolete INTEGER .1.3.6.1.4.1.1548.1.4.1.1 |
dodRemoteMacAddressContains the IEEE unique MAC address of statically
configured devices for bridging purposes. When all of
the 6 bytes of this MAC address are zero, the entry is
called the unknown address. Any packet with a destination
address not in the static or dynamic MAC table of any
remote bridge will be sent to the default remote bridge
(which has a dodRemoteMacAddress entry defined for the
unknown MAC address)..
There can be only one remote destination specified as
default bridge, i.e. containing the unknown MAC address.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.1548.1.4.1.2 |
fpether OBJECT IDENTIFIER .1.3.6.1.4.1.1548.2 |
fpisdn OBJECT IDENTIFIER .1.3.6.1.4.1.1548.3 |
fpsys OBJECT IDENTIFIER .1.3.6.1.4.1.1548.4 |
dodRemoteMacOperationadd
this remote destination.
remove
::= { dodRemoteMacEntry 3 }
dodRemoteIPNetTable OBJECT-TYPE
SYNTAX SEQUENCE OF DodRemoteIPNetEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTIONrw Enumeration .1.3.6.1.4.1.1548.4.9 |
fpWriteTimerThis object retrieves the current security timer value.
It returns how many minutes are left (if any) before
a new login must be performed.ro INTEGER .1.3.6.1.4.1.1548.4.10 |
fpCommunityNameTo change or retrieve the SNMP community name.
The default name is 'public'.rw DisplayString .1.3.6.1.4.1.1548.4.11 |
fpInternetFireWallTo enable or disable the internet firewall filter.
The filter discards any IP packet arriving from the
WAN with a source IP address belonging to the LAN.rw Enumeration .1.3.6.1.4.1.1548.4.12 |
fpSysLogoutWriting to this object prevents any change from any
SNMP manager (until logged in again). Changes from
telnet and the console are controlled via the login
and logout commands, and are independent.
After a reboot, SNMP managers are logged out and
should log in before changing any configuration.rw INTEGER .1.3.6.1.4.1.1548.4.13 |
fpIpxSupportedIndicates whether or not IPX is supported in the
router software. For compatibility with previous
non-IPX-capable builds, the manager should consider
that an error of NOSUCHNAME on this object means
that IPX is NOT supported.ro Enumeration .1.3.6.1.4.1.1548.4.14 |
fpSysCallerIdTableThis table defines the types of connections for which
CallerID information should be verified. SEQUENCE OF FpSysCallerIdEntry .1.3.6.1.4.1.1548.4.15 |
fpSysCallerIdEntryAn entry in the fpSysCallerIdTable specifies that
calls of the type used as an index, should be validated
by Caller ID verification (using dodCallerTable). FpSysCallerIdEntry .1.3.6.1.4.1.1548.4.15.1 |
fpCallerIdEnabledSet this object to enable or disable CallerId
verification for the specified type of connection.rw Enumeration .1.3.6.1.4.1.1548.4.15.1.1 |
fpMIBCompatibilityIndicates that this private MIB is fully compatible
with RFC 1155. For compatibility with previous
builds, the manager should consider that an error
of NOSUCHNAME on this object means that the 'old'
value applies, (meaning the enumeration of INTEGERs
are mostly zero-based instead of one-based).ro Enumeration .1.3.6.1.4.1.1548.4.16 |
fpPOTSInstalledIndicates whether or not POTS hardware is installed
AND is software supported. For compatibility with
previous builds, the manager should consider that
an error of NOSUCHNAME on this object means that
POTS hardware and software are not available.ro Enumeration .1.3.6.1.4.1.1548.4.17 |
fpSysLastLogEventThe last system event reported to the console. This
includes the timestamp, the subsystem and the actual
text message of the event.ro DisplayString .1.3.6.1.4.1.1548.4.18 |
fpSysSingleUserThis IP address used to define the single address to which
IP translation was to occur (one client system at a
time), or cancelling the translation when NULL.
Network Address Translation (NAT) and its ability to
define server mappings (with sysIPTranslationServerTable)
has rendered this object obsolete: this object is now always
returned as the IP address 0.0.0.0 and cannot be set to
anything else.rw NetworkAddress .1.3.6.1.4.1.1548.4.19 |
fpSysYearSet this object to specify the year for the real time
clock, protected by a battery when the power is off.
When all the related parameters (fpSysYear, fpSysMonth,
fpSysDay, fpSysHour, fpSysMinute, fpSysSecond) are set,
set the fpSysOperation to set-clock(5).rw INTEGER .1.3.6.1.4.1.1548.4.20 |
fpSysMonthSet this object to specify the month for the real time
clock, protected by a battery when the power is off.
When all the related parameters (fpSysYear, fpSysMonth,
fpSysDay, fpSysHour, fpSysMinute, fpSysSecond) are set,
set the fpSysOperation to set-clock(5).rw INTEGER .1.3.6.1.4.1.1548.4.21 |
fpSysDaySet this object to specify the day for the real time
clock, protected by a battery when the power is off.
When all the related parameters (fpSysYear, fpSysMonth,
fpSysDay, fpSysHour, fpSysMinute, fpSysSecond) are set,
set the fpSysOperation to set-clock(5).rw INTEGER .1.3.6.1.4.1.1548.4.22 |
fpSysHourSet this object to specify the hour for the real time
clock, protected by a battery when the power is off.
When all the related parameters (fpSysYear, fpSysMonth,
fpSysDay, fpSysHour, fpSysMinute, fpSysSecond) are set,
set the fpSysOperation to set-clock(5).rw INTEGER .1.3.6.1.4.1.1548.4.23 |
fpSysMinuteSet this object to specify the minutes for the real time
clock, protected by a battery when the power is off.
When all the related parameters (fpSysYear, fpSysMonth,
fpSysDay, fpSysHour, fpSysMinute, fpSysSecond) are set,
set the fpSysOperation to set-clock(5).rw INTEGER .1.3.6.1.4.1.1548.4.24 |
fpSysSecondSet this object to specify the seconds for the real time
clock, protected by a battery when the power is off.
When all the related parameters (fpSysYear, fpSysMonth,
fpSysDay, fpSysHour, fpSysMinute, fpSysSecond) are set,
set the fpSysOperation to set-clock(5).rw INTEGER .1.3.6.1.4.1.1548.4.25 |
fpSysDefaultSingleUserNetwork Address Translation (NAT) and its ability to
define server mappings (with sysIPTranslationServerTable)
has rendered this object obsolete.
For backwards compatibility purposes, this object still
allows to set the IP address of the client for which IP
address translation is to be performed by default.
However, to take effect, the configuration must be saved
(with fpEtherOperation=save(1)) and the system must be
restarted.rw NetworkAddress .1.3.6.1.4.1.1548.4.26 |
fpSysBootpRelayThis object allows to get or set the IP address of the
DHCP/BOOTP Server when this router is acting as a Bootp
relay agent. When set to 0.0.0.0, this router will not
act as a Bootp relay agent.
This setting is saved to non-volatile memory, with both
fpSysOperation=save(1) and fpEtherOperation=save(1).rw NetworkAddress .1.3.6.1.4.1.1548.4.27 |
fpSysKernelRevisionThis object represents the number of times that the
source code got changed, possibly resulting in the support
of new features. This number is intended to be used by
an SNMP manager to determine what features set is supported
by the kernel software (compared to what is expected as a
minimum). This objects differs from fpSysSoftwareVer which
is a string containing an administratively defined version.ro INTEGER .1.3.6.1.4.1.1548.4.28 |
fpSysTelnetPortThe TCP port for reception of telnet connections to
the router. Setting this value to zero disables
telnetting to the router. This change requires a
reboot to take affect.rw INTEGER .1.3.6.1.4.1.1548.4.29 |
fpSysSNMPPortThe TCP port for reception of SNMP requests to
the router. Setting this value to zero disables
SNMP management of the router. This change requires a
reboot to take affect.rw INTEGER .1.3.6.1.4.1.1548.4.30 |
fpWAN2WANForwardingTo enable or disable the forwarding of data traffic
from one wan link to another wan link.rw Enumeration .1.3.6.1.4.1.1548.4.31 |
fpUdpRelayTableThis table defines UDP ports for which relaying should
should be performed when this UDP traffic is broadcast. SEQUENCE OF FpUdpRelayEntry .1.3.6.1.4.1.1548.4.32 |
fpUdpRelayEntryAn entry in the fpUdpRelayTable specifies that UDP
packets which are broadcast to the specified ports
should be relayed to the specified IP address. FpUdpRelayEntry .1.3.6.1.4.1.1548.4.32.1 |
fpUdpRelayFirstPortFirst UDP port of range of UDP ports which will be
relayed.ro OCTET STRING .1.3.6.1.4.1.1548.4.32.1.1 |
fpUdpRelayLastPortLast UDP port of range of UDP ports which will be
relayed.ro OCTET STRING .1.3.6.1.4.1.1548.4.32.1.2 |
fpUdpRelayIPAddressIP address to receive UDP broadcast traffic.ro IpAddress .1.3.6.1.4.1.1548.4.32.1.3 |
fpUdpRelayStatusThe status column used for creating, modifying, and
deleting instances of the columnar objects in this table.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1548.4.32.1.4 |
fpOneWANConnectionTo enable or disable the bringing up of more than
one wan link at a time to different destinations.rw Enumeration .1.3.6.1.4.1.1548.4.33 |
fpSysHTTPPortThe TCP port for reception of HTTP requests to
the router. Setting this value to zero disables
HTTP management of the router. This change requires a
reboot to take affect.rw INTEGER .1.3.6.1.4.1.1548.4.34 |
fpDirectedBroadcastsEnable/disable directed broadcasts to a directly
connected interface.rw Enumeration .1.3.6.1.4.1.1548.4.35 |
fpBlockNetBIOSDefaultTo set the default when a new remote is created
that controls if the remote will block NetBIOS
traffic.rw Enumeration .1.3.6.1.4.1.1548.4.36 |
fpSysFlashAvailableThis object represents the number of bytes of flash
available in the flash file system.ro INTEGER .1.3.6.1.4.1.1548.4.37 |
fpVoiceTableThis table defines voice ports for voice routers. SEQUENCE OF FpVoiceEntry .1.3.6.1.4.1.1548.4.38 |
fpVoiceEntryAn entry in the fpVoiceTable specifies voice
information for an voice router; such as the ATM PVC
or the Frame Relay DLCI. FpVoiceEntry .1.3.6.1.4.1.1548.4.38.1 |
fpVoiceIndexThe voice port index number.ro INTEGER .1.3.6.1.4.1.1548.4.38.1.1 |
fpVoicePortThis object represents the ATM PVC or the Frame Relay
DLCI number for the voice port.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1548.4.38.1.2 |
fpEchoTableThis table defines echo ports.deprecated SEQUENCE OF FpEchoEntry .1.3.6.1.4.1.1548.4.39 |
fpEchoEntryAn entry in the fpEchoTable specifies echo
information for a voice router; such as the ATM PVC
or the Frame Relay DLCI.deprecated FpEchoEntry .1.3.6.1.4.1.1548.4.39.1 |
fpEchoIndexThe echo port index number.rodeprecated INTEGER .1.3.6.1.4.1.1548.4.39.1.1 |
fpEchoPortThis object represents the ATM PVC or the Frame Relay
DLCI number for the echo port.rwdeprecated DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1548.4.39.1.2 |
fpOptionTableThis table defines Kernel Options. SEQUENCE OF FpOptionEntry .1.3.6.1.4.1.1548.4.40 |
fpOptionEntryA string in the fpOptionTable specifies information
pertaining to options built into the kernel -and-
which options are available. FpOptionEntry .1.3.6.1.4.1.1548.4.40.1 |
fpOptionIndexAn index number representing a line of options.ro INTEGER .1.3.6.1.4.1.1548.4.40.1.1 |
fpOptionStringThis object represents a an string for the option
built into the kernel.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1548.4.40.1.2 |
fpOptionAvailableReturns enable(1) if the option is available for use.ro Enumeration .1.3.6.1.4.1.1548.4.40.1.3 |
fplogin OBJECT IDENTIFIER .1.3.6.1.4.1.1548.5 |
fpLoginTableThis object returns the login status to the Manager. SEQUENCE OF FpLoginEntry .1.3.6.1.4.1.1548.5.1 |
fpLoginEntry FpLoginEntry .1.3.6.1.4.1.1548.5.1.1 |
fpWan OBJECT IDENTIFIER .1.3.6.1.4.1.1548.6 |
fppots OBJECT IDENTIFIER .1.3.6.1.4.1.1548.7 |
fpdownload OBJECT IDENTIFIER .1.3.6.1.4.1.1548.8 |
fpiptranslate OBJECT IDENTIFIER .1.3.6.1.4.1.1548.9 |
fpdhcp OBJECT IDENTIFIER .1.3.6.1.4.1.1548.10 |
fpdir OBJECT IDENTIFIER .1.3.6.1.4.1.1548.11 |
fpatm OBJECT IDENTIFIER .1.3.6.1.4.1.1548.12 |
fpfr OBJECT IDENTIFIER .1.3.6.1.4.1.1548.13 |
fpLoginActionThis object will return the login status to the Manager.
Use this object to login to system by giving the
administrator's password as index. The login status are:
1
2
::= { fpLoginEntry 1 }
fpWanTable OBJECT-TYPE
SYNTAX SEQUENCE OF FpWanEntry
ACCESS not-accessible
STATUS mandatory
DESCRIPTIONro Enumeration .1.3.6.1.4.1.1548.13.1 |