FC-PORT-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
466
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
466 total| Object Name |
|---|
fsPortDefinition OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.10.1 |
RFC1155-SMI Unknown .1.3.6.1.4.1.635.1.2.1.10.1 |
fsPortDefTable SEQUENCE OF FsPortDefEntry .1.3.6.1.4.1.635.1.2.1.10.1.1 |
fsPortDefEntry FsPortDefEntry .1.3.6.1.4.1.635.1.2.1.10.1.1.1 |
fsPortDefLogPortNorw Enumeration .1.3.6.1.4.1.635.1.2.1.10.1.1.1.1 |
fsPortDefPhyBoardNorw Enumeration .1.3.6.1.4.1.635.1.2.1.10.1.1.1.2 |
fsPortDefPhyPortNorw Enumeration .1.3.6.1.4.1.635.1.2.1.10.1.1.1.3 |
fsPortDefProtocolrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.1.1.1.4 |
fsPortDefStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.1.1.1.5 |
fsPortDialupConfigTable SEQUENCE OF FsPortDialupConfigEntry .1.3.6.1.4.1.635.1.2.1.10.1.2 |
fsPortDialupConfigEntry FsPortDefEntry .1.3.6.1.4.1.635.1.2.1.10.1.2.1 |
fsPortDialupLogPortNorw Enumeration .1.3.6.1.4.1.635.1.2.1.10.1.2.1.1 |
fsPortDialupDialModerw Enumeration .1.3.6.1.4.1.635.1.2.1.10.1.2.1.2 |
fsPortDialupPrimaryPherw DisplayString .1.3.6.1.4.1.635.1.2.1.10.1.2.1.3 |
fsPortDialupSecondPherw DisplayString .1.3.6.1.4.1.635.1.2.1.10.1.2.1.4 |
fsPortDialupRedialTimerrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.1.2.1.5 |
fsPortDialupNumRedialrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.1.2.1.6 |
fsPortDialupDialPortPrirw Enumeration .1.3.6.1.4.1.635.1.2.1.10.1.2.1.7 |
fsPortDialupTollSaverrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.1.2.1.8 |
fsPortDialupTollSaverTimeoutrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.1.2.1.9 |
fsPortDialupMaxNumSucCallsrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.1.2.1.10 |
fsPortDialupLocalTelrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.1.2.1.11 |
fsPortDialISDNDataRaterw Enumeration .1.3.6.1.4.1.635.1.2.1.10.1.2.1.12 |
fsPortDialStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.1.2.1.13 |
fsFrameRelay OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.10.2 |
fsFrameRelayDefTable SEQUENCE OF FsFrameRelayDefEntry .1.3.6.1.4.1.635.1.2.1.10.2.1 |
fsFrameRelayDefEntry FsFrameRelayDefEntry .1.3.6.1.4.1.635.1.2.1.10.2.1.1 |
fsFrameRelayPortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.10.2.1.1.1 |
fsFrameRelaySpeedThe sync speed the FRAD will provide/accept clock to/from the
networkrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.2.1.1.2 |
fsFrameRelayProtocolSelect the type of Frame Relay management protocol to use
on the port.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.2.1.1.3 |
fsFrameRelayN1The STATUS_ENQUIRY message typically is a request for
the Sequence Number Exchange Only (report type= 00000001).
Every N1 polling intervals the user device requests a Full
Status Message (report type= 00000000).rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.2.1.1.4 |
fsFrameRelayN2Value N2 is the number of error events that must be
detected in the last N3 events in order for the link to be
considered down.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.2.1.1.5 |
fsFrameRelayN3Value N3 is the number of events in which N2 errors must
be detected for the link to be considered down. It is
also the number of events that must occur with no N2
errors in order for the link to be considered back up.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.2.1.1.6 |
fsFrameRelayT1T1 is the length of the time spent waiting for a STATUS
message after sending STATUS_ENQUIRY (user devices).rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.2.1.1.7 |
fsFrameRelayT2T2 is the time the network will spend waiting for a
STATUS_ENQUIRY from user devices.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.2.1.1.8 |
fsFrameRelayPriEnableEnable priority queuing for the port.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.2.1.1.9 |
fsFrameRelayPriHiToMedThis is the ratio of number of bytes sent for
High priority data to Medium priority data.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.2.1.1.10 |
fsFrameRelayPriMedToLowThis is the ratio of number of bytes sent for
Medium priority data to Low priority data.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.2.1.1.11 |
fsFrameRelayStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.2.1.1.12 |
fsFrameRelayPriDlciTable SEQUENCE OF FsFrameRelayPriDlciEntry .1.3.6.1.4.1.635.1.2.1.10.2.2 |
fsFrameRelayPriDlciEntry FsFrameRelayPriDlciEntry .1.3.6.1.4.1.635.1.2.1.10.2.2.1 |
fsFRPriPortNorw Enumeration .1.3.6.1.4.1.635.1.2.1.10.2.2.1.1 |
fsFRPriIndexrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.2.2.1.2 |
fsFRPriDlciNumThis is the DLCI to use for the data.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.2.2.1.3 |
fsFRPriDlciCIRThis is the CIR for the DLCI.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.2.2.1.4 |
fsFRPriDlciBcThis is the committed burst rate for the PVC.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.2.2.1.5 |
fsFRPriDlciBeThis is the excess burst rate to use for the PVC.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.2.2.1.6 |
fsFRPriStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.2.2.1.7 |
fsAsyncEncapsulation OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.10.3 |
fsAsyncEncapDefTable SEQUENCE OF FsAsyncEncapDefEntry .1.3.6.1.4.1.635.1.2.1.10.3.1 |
fsAsyncEncapDefEntry FsAsyncEncapDefEntry .1.3.6.1.4.1.635.1.2.1.10.3.1.1 |
fsAsyncEncapPortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.10.3.1.1.1 |
fsAsyncEncapSpeedThe async speed of the user's equipmentrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.3.1.1.2 |
fsAsyncEncapDataBitsThe number of bits in the data bytes.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.3.1.1.3 |
fsAsyncEncapParityThe type of parity used for the data.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.3.1.1.4 |
fsAsyncEncapStopBitsThe number of stop bits to use for the data.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.3.1.1.5 |
fsAsyncEncapPriThe priority setting for the data (immediate,
high, medium, low).rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.3.1.1.6 |
fsAsyncEncapDestinationPortThe destination port of the remote FRAD.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.3.1.1.7 |
fsAsyncEncapBreakLengthSet the length of a break character.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.3.1.1.8 |
fsAsyncEncapGptNamerw DisplayString .1.3.6.1.4.1.635.1.2.1.10.3.1.1.9 |
fsAsyncEncapStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.3.1.1.10 |
fsBitSyncEncapsulation OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.10.4 |
fsBitSyncEncapDefTable SEQUENCE OF FsBitSyncEncapDefEntry .1.3.6.1.4.1.635.1.2.1.10.4.1 |
fsBitSyncEncapDefEntry FsBitSyncEncapDefEntry .1.3.6.1.4.1.635.1.2.1.10.4.1.1 |
fsBitSyncEncapPortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.10.4.1.1.1 |
fsBitSyncEncapSpeedThe sync speed the FRAD will provide/accept
clock to/from the user's equipmentrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.4.1.1.2 |
fsBitSyncEncapFormatThe format of the HDLC frame (NRZ, NRZI).rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.4.1.1.3 |
fsBitSyncEncapSwitchedDcdSwitched DCD is usually used for AS400 users in order
to simulate the functionality of a multipoint network.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.4.1.1.4 |
fsBitSyncEncapIdleMarkSDLC device use different filler characters in
between actual data packets. Select either 'mark'
or flag (7E).rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.4.1.1.5 |
fsBitSyncEncapPriPriority setting for the data (immediate, high,
medium, low).rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.4.1.1.6 |
fsBitSyncEncapGptNamerw DisplayString .1.3.6.1.4.1.635.1.2.1.10.4.1.1.7 |
fsBitSyncEncapStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.4.1.1.8 |
fsSLIP OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.10.7 |
fsSlipDefTable SEQUENCE OF FsSlipDefEntry .1.3.6.1.4.1.635.1.2.1.10.7.1 |
fsSlipDefEntry FsSlipDefEntry .1.3.6.1.4.1.635.1.2.1.10.7.1.1 |
fsSlipPortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.10.7.1.1.1 |
fsSlipSpeedrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.7.1.1.2 |
fsSlipStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.7.1.1.3 |
fsAsyncBurosEmulation OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.10.9 |
fsAsyncBurosEmulateDefTable SEQUENCE OF FsAsyncBurosEmulateDefEntry .1.3.6.1.4.1.635.1.2.1.10.9.1 |
fsAsyncBurosEmulateDefEntry FsAsyncBurosEmulateDefEntry .1.3.6.1.4.1.635.1.2.1.10.9.1.1 |
fsAsyncBurosEmulatePortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.10.9.1.1.1 |
fsAsyncBurosEmulateSpeedThe sync speed the FRAD will provide/accept clock to/from the
user's equipmentrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.9.1.1.2 |
fsAsyncBurosEmulateTypeThe Asynchronous Burroughs parameters allows
you to set the Polling Emulation Type. The FRAD port
must be configured as either Host or Terminal,
depending on which device is connected to the port.
If the FRAD port you are configuring is connected to a Host,
type '1'. If it is connected to a Terminal, type '2'.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.9.1.1.3 |
fsAsyncBurosEmulateResTimeoutAsynchronous Burroughs parameters allows you to set
the Terminal Timer. The default is three seconds.
This timer needs to be set only if you selected Terminal
as the Polling Emulation Type.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.9.1.1.4 |
fsAsyncBurosEmulateCtsDelayrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.9.1.1.5 |
fsAsyncBurosEmulateStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.9.1.1.6 |
fsAsyncBurosTable SEQUENCE OF FsAsyncBurosEntry .1.3.6.1.4.1.635.1.2.1.10.9.2 |
fsAsyncBurosEntry FsAsyncBurosEntry .1.3.6.1.4.1.635.1.2.1.10.9.2.1 |
fsAsyncBurosPortNorw Enumeration .1.3.6.1.4.1.635.1.2.1.10.9.2.1.1 |
fsAsyncBurosIndexro INTEGER .1.3.6.1.4.1.635.1.2.1.10.9.2.1.2 |
fsAsyncBurosLocalLogicalIdThe FRAD transfers data between logical units.
This means that the FRAD doesn't deal with real
controllers but maps real controllers to artificial
logical units. This is done so that the FRAD can,
for example, map a real control unit that has address
C1 onto a controller that is known to the host as D2.
In this way point-to-point terminals at one end of
the network can be made to appear as a multi-dropped
line to the host. The Local Logical ID number is the
unique identifying number in the FRAD that is then
mapped through this table to a real controller.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.9.2.1.3 |
fsAsyncBurosLocalDeviceAddrThis is the address of either a physical
controller to be polled if the FRAD port is configured
for terminal or a controller for which the FRAD
will answer if the FRAD port is configured for Host.rw DisplayString .1.3.6.1.4.1.635.1.2.1.10.9.2.1.4 |
fsAsyncBurosLocalGroupAddrControllers (terminals) in Burroughs Poll/Select
can be referred to by a group address. When a group
address is used in a poll, any terminal in that group
is permitted to respond.rw DisplayString .1.3.6.1.4.1.635.1.2.1.10.9.2.1.5 |
fsAsyncBurosRemoteIPaddrThis is the IP address of the device that will
receive messages sent from this FRAD port.
Every FRAD has an IP address.rw IpAddress .1.3.6.1.4.1.635.1.2.1.10.9.2.1.6 |
fsAsyncBurosRemoteLogicalId- This is the logical ID of the remote device
which will receive messages sent from this FRAD port.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.9.2.1.7 |
fsAsyncBurosStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.9.2.1.8 |
fsSyncBurosEmulation OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.10.10 |
fsSyncBurosEmulateDefTable SEQUENCE OF FsSyncBurosEmulateDefEntry .1.3.6.1.4.1.635.1.2.1.10.10.1 |
fsSyncBurosEmulateDefEntry FsSyncBurosEmulateDefEntry .1.3.6.1.4.1.635.1.2.1.10.10.1.1 |
fsSyncBurosEmulatePortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.10.10.1.1.1 |
fsSyncBurosEmulateSpeedThe sync speed the FRAD will provide/accept clock to/from the
user's equipmentrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.10.1.1.2 |
fsSyncBurosEmulateTypeIf the FRAD port you are configuring is connected
to a Host, type '1'. If it is connected to a Terminal,
type '2'.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.10.1.1.3 |
fsSyncBurosEmulateResTimeoutrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.10.1.1.4 |
fsSyncBurosEmulateCtsDelayrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.10.1.1.5 |
fsSyncBurosEmulateStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.10.1.1.6 |
fsSyncBurosTable SEQUENCE OF FsSyncBurosEntry .1.3.6.1.4.1.635.1.2.1.10.10.2 |
fsSyncBurosEntry FsSyncBurosEntry .1.3.6.1.4.1.635.1.2.1.10.10.2.1 |
fsSyncBurosPortNorw Enumeration .1.3.6.1.4.1.635.1.2.1.10.10.2.1.1 |
fsSyncBurosIndexro INTEGER .1.3.6.1.4.1.635.1.2.1.10.10.2.1.2 |
fsSyncBurosLocalLogicalIdThe FRAD transfers data between logical units.
This means that the FRAD doesn't deal with real
controllers but maps real controllers to artificial
logical units. This is done so that the FRAD can,
for example, map a real control unit at a site
that may have an address of C1 onto a controller
that is known to the host as D2. In this way
point-to-point terminals at one end of the network
can be made to appear as a multi-dropped line to the
host. The Local Logical ID number is the unique
identifying number in the FRAD that is then mapped
through this table to a real controller.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.10.2.1.3 |
fsSyncBurosLocalDeviceAddrThis is the address of either a physical
controller to be polled if the FRAD port is
configured for terminal or a controller for
which the FRAD will answer if the FRAD port is
configured for Host.rw DisplayString .1.3.6.1.4.1.635.1.2.1.10.10.2.1.4 |
fsSyncBurosLocalGroupAddrIf you have selected 'Host' for the Polling
Emulation Type, the Local Logical ID option
will reappear. You can either add more addresses
or press <ESC> to exit. If you exit, you will
see a list of the addresses which have been entered
and be given the option to add, modify or delete.rw DisplayString .1.3.6.1.4.1.635.1.2.1.10.10.2.1.5 |
fsSyncBurosRemoteIPaddrThis is the IP address of the device that will
receive messages sent from this FRAD port.
Every FRAD has an IP address.rw IpAddress .1.3.6.1.4.1.635.1.2.1.10.10.2.1.6 |
fsSyncBurosRemoteLogicalId- This is the logical ID of the remote device
which will receive messages sent from this FRAD port.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.10.2.1.7 |
fsSyncBurosStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.10.2.1.8 |
fsSdlcRoute OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.10.11 |
fsSdlcRouteDefTable SEQUENCE OF FsSdlcRouteDefEntry .1.3.6.1.4.1.635.1.2.1.10.11.1 |
fsSdlcRouteDefEntry FsSdlcRouteDefEntry .1.3.6.1.4.1.635.1.2.1.10.11.1.1 |
fsSdlcRoutePortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.10.11.1.1.1 |
fsSdlcRouteSpeedThe sync speed the FRAD will provide/accept clock to/from the
user's equipmentrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.11.1.1.2 |
fsSdlcRouteFormatThe SDLC Routing parameters allows you to set the
Data Format. There are two data formats:
Non-Return-to-Zero (NRZ) and Non-Return-to-Zero
Inverted (NRZI). Check your equipment specifications
to determine which you are usingrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.11.1.1.3 |
fsSdlcRouteSwitchedDcdThe SDLC Routing Parameters menu allows you to
determine when DCD will be active. It is only
effective on ports set up as DCE interfaces.
If DCD is set to Switched, DCD will only be active
during data transmission from the FRAD. If set to
Forced, DCD will remain active at all times.
The default for this parameter is Forced.
(Prior to implementation of this option, a DCE port
would raise DCD and keep it active at all times.)rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.11.1.1.4 |
fsSdlcRouteIdleMarkIdle Character on the SDLC Routing Parameters menu
allows you to select transmission of Mark characters
between frames, except after frames whose Poll/Final
(P/F) bit is clear (off). Normally, an HDLC protocol
transmits HDLC Flag (0x7e with no zero insertion)
characters between frames. If Idle Character is set to
Flag, the FRAD will continue to issue HDLC Flag
characters in the idle state. If Idle Character is set
to Mark, the FRAD will send solid Mark characters
(all binary ones) in the idle state. The exception is
that any frame which does not have the P/F flag of the
command byte set (bit 0x10 of the second byte of the frame)
will be followed by HDLC Flag characters. (This exception
was explicitly designed for compatibility with IBM AS400s.
However, it does reflect the actual state of an HDLC line
over half-duplex modems.) The default for this parameter
is Flag.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.11.1.1.5 |
fsSdlcRouteStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.11.1.1.6 |
fsSdlcRouteConTable SEQUENCE OF FsSdlcRouteConEntry .1.3.6.1.4.1.635.1.2.1.10.11.2 |
fsSdlcRouteConEntry FsSdlcRouteConEntry .1.3.6.1.4.1.635.1.2.1.10.11.2.1 |
fsSdlcRouteConPortNorw Enumeration .1.3.6.1.4.1.635.1.2.1.10.11.2.1.1 |
fsSdlcRouteConIndexro INTEGER .1.3.6.1.4.1.635.1.2.1.10.11.2.1.2 |
fsSdlcRouteConAddrType the SDLC controller address.rw DisplayString .1.3.6.1.4.1.635.1.2.1.10.11.2.1.3 |
fsSdlcRouteGptNamerw DisplayString .1.3.6.1.4.1.635.1.2.1.10.11.2.1.4 |
fsSdlcRouteConPriEnter the priority level of the data.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.11.2.1.5 |
fsSdlcRouteConStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.11.2.1.6 |
fsByteSyncEncapsulation OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.10.12 |
fsByteSyncEncapDefTable SEQUENCE OF FsByteSyncEncapDefEntry .1.3.6.1.4.1.635.1.2.1.10.12.1 |
fsByteSyncEncapDefEntry FsByteSyncEncapDefEntry .1.3.6.1.4.1.635.1.2.1.10.12.1.1 |
fsByteSyncEncapPortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.10.12.1.1.1 |
fsByteSyncEncapSpeedThe sync speed the FRAD will provide/accept clock to/from the
user's equipmentrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.12.1.1.2 |
fsByteSyncEncapPriSelect the data's priority level.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.12.1.1.3 |
fsByteSyncEncapDestinationPortSelect the destination port of the remote FRAD.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.12.1.1.4 |
fsByteSyncEncapCodeSelect the code set to use.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.12.1.1.5 |
fsByteSyncEncapGptNamerw DisplayString .1.3.6.1.4.1.635.1.2.1.10.12.1.1.6 |
fsByteSyncEncapStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.12.1.1.7 |
fsTelnetTerminal OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.10.13 |
fsTelnetTermDefTable SEQUENCE OF FsTelnetTermDefEntry .1.3.6.1.4.1.635.1.2.1.10.13.1 |
fsTelnetTermDefEntry FsTelnetTermDefEntry .1.3.6.1.4.1.635.1.2.1.10.13.1.1 |
fsTelnetTermPortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.10.13.1.1.1 |
fsTelnetTermSpeedThe async speed of the user's equipmentrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.13.1.1.2 |
fsTelnetTermDataBitsSelect the number of data bits.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.13.1.1.3 |
fsTelnetTermParitySelect the parity to be used.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.13.1.1.4 |
fsTelnetTermStopBitsSelect the number of stop bits.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.13.1.1.5 |
fsTelnetTermFlowControlFlow control can be enabled for transmit
only, receive only or both directions for either
of the two Flow Control Types.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.13.1.1.6 |
fsTelnetTermFCTypeSelect the type of flow control. Both RTS/CTS
hardware flow control and XON/XOFF software flow
control are supported.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.13.1.1.7 |
fsTelnetTermConnectionTypeThis parameter determines how the Telnet Client
terminal will initiate a connection with the Telnet
Server. You can select Manual connection or DTR Dial.
In the manual mode, you manually enter an IP Address
to connect to a Telnet Server by using the Telnet
Terminal Commands Menu (see Section 5.16.19) on the
local terminal. This menu can also be used to PING a
remote Server. Pressing <CTRL> 'X' will end the
Telnet session. It can also be terminated from the
remote end. In the DTR dial mode, Telnet Terminal will
initiate a Telnet connection to a remote Telnet Server
immediately after the port's DTR is enabled. The remote
TCP port and remote IP address configured in the Telnet
Terminal Parameters menu will be used to make the connection.
The connection is closed when DTR is off. Note that DTR
can be forced on as described above.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.13.1.1.8 |
fsTelnetTermAnswerModeThis parameter allows you to set the port to
act as a Telnet Server by turning on the Answer Mode.
The port will then respond to Telnet Clients attempting
to make a connection. If the Answer Mode is off, the
port will not answer Telnet calls.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.13.1.1.9 |
fsTelnetTermDataModeThis parameter allows you to set the Data Mode.
There are two modes: normal and binary. The Normal data
mode uses 'Control X' as an escape character. It allows
parameter handshaking after connection. The binary data
mode is in accordance with RFC 856. When in Binary Data
mode, the only available method for dropping a connection
is to drop the DTR control signal on either end of the
connection. (Note that dropping DTR drops the connection
in Normal mode as well.) The default for this parameter
is Normal.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.13.1.1.10 |
fsTelnetTermNullModerw Enumeration .1.3.6.1.4.1.635.1.2.1.10.13.1.1.11 |
fsTelnetTermQuietModeWhen the Telnet Module Connection Type is configured
as 'Manual' and there is no active Telnet session
on a given port, the Telnet Command menu will be
displayed on the associated terminal. Quiet Mode allows
you to disable this display. This capability is useful
if a host machine or computer connected to the Telnet
port does not tolerate the menu characters being
received from the Telnet port. The default for this
option is Off.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.13.1.1.12 |
fsTelnetTermLocalEchoLocal Echo is a straight forward mechanism for
displaying data which can be configured in the
FRAD by an On, Off or Auto selection. The Local
Echo option has three possible settings. If it is
enabled, the FRAD will always echo characters
received from the terminal back to the terminal.
If Local Echo is disabled, the FRAD will not echo
received characters back to the terminal.
When Local Echo is set to Auto, the FRAD will echo
characters back to the local terminal only if the
remote echo option has not been successfully negotiated
between the local and remote Telnet modules (the FRAD
is performing the Store and Forward option).rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.13.1.1.13 |
fsTelnetTermRemoteEchoThere are three settings for this option-
Enabled: The FRAD will not attempt to negotiate
the Telnet echo option and will refuse to implement
it even if the remote Telnet module requests it to
do so. The FRAD will always store data from the local
terminal until a <CR> is received or the buffer is
filled, then forwards it to the host. Disabled:
The FRAD will attempt to negotiate the Telnet echo
option and will implement it if requested by the remote
Telnet module. The FRAD will forward all received data
immediately to the host even if the remote Telnet
module refused the negotiation. Auto: The FRAD will
attempt to negotiate the Telnet echo option and will
implement it if requested. If the negotiation fails,
the FRAD will store and forward data. If the negotiation
succeeds, the FRAD will forward all data received from
the local terminal immediately.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.13.1.1.14 |
fsTelnetTermForceDTRThis option allows you to force DTR to be On. Forcing
a DTR signal is useful if the terminal equipment
connected to the FRAD port fails to supply DTR.
This will also prevent a Telnet session from being
disconnected if DTR is dropped.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.13.1.1.15 |
fsTelnetTermForceDCDThis option allows you to force DCD to be On.
The Telnet module raises and lowers this control
signal to indicate the connection status of its
Telnet session. Forcing the signal On is useful
if the varying DCD signal has a negative effect
on the operation of the attached terminal.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.13.1.1.16 |
fsTelnetTermForceDSRThis option allows you to force DSR to be On.
The Telnet module raises and lowers this control
signal to indicate the connection status of its
Telnet session. Forcing the signal On is useful
if the varying DSR signal has a negative effect on
the operation of the attached terminal.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.13.1.1.17 |
fsTelnetTermLocalTCPThis option allows you to enter the Local TCP Port.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.13.1.1.18 |
fsTelnetTermRemoteTCPThis option allows you to enter the Remote TCP Port
number. If you are using the DTR Dial or Continuous
Connection Types, the number entered here will be used
to establish a Telnet session. If you are using the
Manual Connection Type, you do not need to enter
this number.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.13.1.1.19 |
fsTelnetTermRemoteIPEnter the IP address of the remote device.rw IpAddress .1.3.6.1.4.1.635.1.2.1.10.13.1.1.20 |
fsTelnetTermXpadLogPortrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.13.1.1.21 |
fsTelnetTermStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.13.1.1.22 |
fsALC OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.10.16 |
fsALCDefTable SEQUENCE OF FsALCDefEntry .1.3.6.1.4.1.635.1.2.1.10.16.1 |
fsALCDefEntry FsALCDefEntry .1.3.6.1.4.1.635.1.2.1.10.16.1.1 |
fsALCPortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.10.16.1.1.1 |
fsALCSpeedrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.16.1.1.2 |
fsALCPollTimerw INTEGER .1.3.6.1.4.1.635.1.2.1.10.16.1.1.3 |
fsALCTimeOutrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.16.1.1.4 |
fsALCControllerIArw DisplayString .1.3.6.1.4.1.635.1.2.1.10.16.1.1.5 |
fsALCControllerIPAddrrw IpAddress .1.3.6.1.4.1.635.1.2.1.10.16.1.1.6 |
fsALCRemoteHostIPAddrrw IpAddress .1.3.6.1.4.1.635.1.2.1.10.16.1.1.7 |
fsALCESDIPAddrrw IpAddress .1.3.6.1.4.1.635.1.2.1.10.16.1.1.8 |
fsALCStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.16.1.1.9 |
fsSDLC2 OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.10.20 |
fsSDLC2DefTable SEQUENCE OF FsSDLC2DefEntry .1.3.6.1.4.1.635.1.2.1.10.20.1 |
fsSDLC2DefEntry FsSDLC2DefEntry .1.3.6.1.4.1.635.1.2.1.10.20.1.1 |
fsSDLC2PortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.10.20.1.1.1 |
fsSDLC2SpeedThe sync speed the FRAD will provide/accept clock to/from the
user's equipmentrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.20.1.1.2 |
fsSDLC2PollTyperw Enumeration .1.3.6.1.4.1.635.1.2.1.10.20.1.1.3 |
fsSDLC2DataFmtData Format for the port.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.20.1.1.4 |
fsSDLC2IdleMarkIdle/Mark for the port.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.20.1.1.5 |
fsSDLC2DCDrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.20.1.1.6 |
fsSDLC2UserBuffHighHigh-water mark for user buffers.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.20.1.1.7 |
fsSDLC2UserBuffLowHigh-water mark for user buffers.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.20.1.1.8 |
fsSDLC2Statusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.20.1.1.9 |
fsSDLC2StnTable SEQUENCE OF FsSDLC2StnEntry .1.3.6.1.4.1.635.1.2.1.10.20.2 |
fsSDLC2StnEntry FsSDLC2StnEntry .1.3.6.1.4.1.635.1.2.1.10.20.2.1 |
fsSDLC2StnPortNorw Enumeration .1.3.6.1.4.1.635.1.2.1.10.20.2.1.1 |
fsSDLC2StnIndexro INTEGER .1.3.6.1.4.1.635.1.2.1.10.20.2.1.2 |
fsSDLC2StnAddrThis value is the poll address of the
secondary link station for this SDLC link. It
uniquely identifies the SDLC link station
within a single SDLC port.rw DisplayString .1.3.6.1.4.1.635.1.2.1.10.20.2.1.3 |
fsSDLC2DuplexModeThis object controls the transmit-receive
capabilities for this SDLC link station.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.20.2.1.4 |
fsSDLC2StnRWindowThis object controls the maximum number of
unacknowledged I-frames which an SDLC link
station may receive. This should range from 1
to 7.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.20.2.1.5 |
fsSDLC2StnXWindowThis object controls the maximum number of
consecutive unacknowledged I-frames which an
SDLC link station shall send without an
acknowledgement. This shall range from 1 to 7.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.20.2.1.6 |
fsSDLC2InactTimerrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.20.2.1.7 |
fsSDLC2AckTimerrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.20.2.1.8 |
fsSDLC2MaxRetriesrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.20.2.1.9 |
fsSDLC2StnStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.20.2.1.10 |
fsX25NEW OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.10.21 |
fsX25NEWL1DefTable SEQUENCE OF FsX25NEWL1DefEntry .1.3.6.1.4.1.635.1.2.1.10.21.1 |
fsX25NEWL1DefEntry FsX25NEWL1DefEntry .1.3.6.1.4.1.635.1.2.1.10.21.1.1 |
fsX25NEWL1PortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.10.21.1.1.1 |
fsX25NEWL1SpeedThe sync speed the FRAD will provide/accept clock to/from the
user's equipmentrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.21.1.1.2 |
fsX25NEWL1GptNamerw DisplayString .1.3.6.1.4.1.635.1.2.1.10.21.1.1.3 |
fsX25NEWL1Statusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.21.1.1.4 |
fsX25NEWL2DefTable SEQUENCE OF FsX25NEWL2DefEntry .1.3.6.1.4.1.635.1.2.1.10.21.2 |
fsX25NEWL2DefEntry FsX25NEWL2DefEntry .1.3.6.1.4.1.635.1.2.1.10.21.2.1 |
fsX25NEWL2PortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.10.21.2.1.1 |
fsX25NEWL2ModeThe LAPB Mode.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.21.2.1.2 |
fsX25NEWL2LinkActivatorThis identifies which node, DTE or DCE, will activate the
link.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.21.2.1.3 |
fsX25NEWL2T1AckTimerThe T1 timer for this interface. It specifies the
maximum time to wait for acknowledgment of a PDU.
This timer is in seconds.
The default value is 3.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.21.2.1.4 |
fsX25NEWL2T2ResTimerThe default T2 timer for this interface. This
specifies the maximum time to wait before sending an
acknowledgment for a sequenced PDU. A value of zero
means there will be no delay in acknowledgement
generation.
This value is entered in seconds.
The default value is 1.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.21.2.1.5 |
fsX25NEWL2T3DisconnectTimerThe T3 timer for this interface. This specifies the
time to wait before considering the link disconnected.
A value of zero indicates the link will be considered
disconnected upon completion of the frame exchange to
disconnect the link.
This value is expressed in seconds.
The default value is 60.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.21.2.1.6 |
fsX25NEWL2N2RetryCountThe default N2 retry counter for this interface. This
specifies the number of times a PDU will be resent
after the T1 timer expires without an acknowledgement
for the PDU.
The default value is 20.
The valid values range from 0 to 65535.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.21.2.1.7 |
fsX25NEWL2SequenceLAPB Sequencing.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.21.2.1.8 |
fsX25NEWL2RxKWindowSizeThe default receive window size for this Interface.
This is the maximum number of unacknowledged sequenced
PDUs that may be outstanding from this DTE at any one
time.
The default value is 7.
The valid values range from 1 to 127.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.21.2.1.9 |
fsX25NEWL2TxKWindowSizeThe default transmit window size for this Interface.
PDUs that may be outstanding from this DTE at any one
time.
The default value is 7.
The valid values range from 1 to 127.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.21.2.1.10 |
fsX25NEWL2Statusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.21.2.1.11 |
fsX25NEWL3DefTable SEQUENCE OF FsX25NEWL3DefEntry .1.3.6.1.4.1.635.1.2.1.10.21.3 |
fsX25NEWL3DefEntry FsX25NEWL3DefEntry .1.3.6.1.4.1.635.1.2.1.10.21.3.1 |
fsX25NEWL3PortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.10.21.3.1.1 |
fsX25NEWL3ModeIdentifies DCE/DTE mode in which the interface
operates.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.21.3.1.2 |
fsX25NEWL3TxPacketSizeThe transmit packet size in octets for a circuit. If
this parameter is changed and if there are any active
VCs, the port will be reinitialized (PVCs will be
reset and SVCs will be cleared).
The default value is 128.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.21.3.1.3 |
fsX25NEWL3RxPacketSizeThe receive packet size in octets for a circuit. If
this parameter is changed and if there are any active
VCs, the port will be reinitialized (PVCs will be
reset and SVCs will be cleared).
The default value is 128.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.21.3.1.4 |
fsX25NEWL3SequencingThe modulus of the packet sequence number space.
The default value is 'modulo8'.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.21.3.1.5 |
fsX25NEWL3TxWindowSizeThe receive packet size in octets for a circuit. If
this parameter is changed and if there are any active
VCs, the port will be reinitialized (PVCs will be
reset and SVCs will be cleared).
The default value is 7.
The valid values range from 1 to 127.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.21.3.1.6 |
fsX25NEWL3RxWindowSizeThe receive window size for a circuit. If this
parameter is changed and if there are any active VCs,
the particular port will be reinitialized (PVCs will be
reset and SVCs will be cleared).
The default value is 7.
The valid values range from 1 to 127.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.21.3.1.7 |
fsX25NEWL3RestartTimerThe T20 restart timer in seconds.
The default value is 180.
The valid values range from 10 to 600.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.21.3.1.8 |
fsX25NEWL3CallTimerThe T21 Call timer in seconds.
The default value is 200.
The valid values range from 10 to 600.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.21.3.1.9 |
fsX25NEWL3ResetTimerThe T22 Reset timer in seconds.
The default value is 180.
The valid values range from 10 to 600.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.21.3.1.10 |
fsX25NEWL3ClearTimerThe T23 Clear timer in seconds.
The default value is 180.
The valid values range from 10 to 600.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.21.3.1.11 |
fsX25NEWL3InputCallFacOptThis field controls the manner in which this port
will respond when presented with any input Call
Packet containing faciliities that are not actively
supported by the system.
Regardless of the value of this object, the
system will always clear calls containing
Flow Control Parameter Negotiation facilities
and will handle Reverse Charging facilities as
configured by the operator.
The value of this object will have no effect on
system-generated call processing; any facility
present in calls received by multiprotocol switching
applications will always be ignored.
If this object is set to 'pass-facilities-through',
which is the default, unsupported facilities
will be passed unchanged through the system.
If this object is set to 'remove-facilities',
unsupported facilities will be stripped from
the packet before it is passed on through the
system.
If this object is set to 'clear-call', calls
using unsupported facilities will be cleared
by the system with the Invalid Facility Clear
Cause and Diagnostic Code combination.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.21.3.1.12 |
fsX25NEWL3OutputCallFacOptThis field controls the manner in which this port
will respond when presented with any output Call
Packet containing faciliities that are not
actively supported by the system.
Regardless of the value of this object, the
system will always clear calls containing
Flow Control Parameter Negotiation facilities
and will handle Reverse Charging facilities as
configured by the operator.
The value of this object will have no effect on
system-generated call processing; any facility
present in calls received by multiprotocol switching
applications will always be ignored.
If this object is set to 'pass-facilities-through',
which is the default, unsupported facilities
will be passed unchanged through the system.
If this object is set to 'remove-facilities',
unsupported facilities will be stripped from
the packet before it is passed on through the
system.
If this object is set to 'clear-call', calls
using unsupported facilities will be cleared
by the system with the Invalid Facility Clear
Cause and Diagnostic Code combination.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.21.3.1.13 |
fsX25NEWL3HPVCLowest Incoming channel.
The default value is 0.
The valid values range from 0 to 4095.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.21.3.1.14 |
fsX25NEWL3LSVCHighest Incoming channel. A value of zero indicates no
channels in this range.
The default value is 0.
The valid values range from 0 to 4095.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.21.3.1.15 |
fsX25NEWL3HSVCLowest Two-way channel.
The default value is 1.
The valid values range from 1 to 4095.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.21.3.1.16 |
fsX25NEWL3MaxActiveVCMaximum Active VCs at a time.
The default value is 20.
The valid values range from 0 to 100.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.21.3.1.17 |
fsX25NEWL3Statusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.21.3.1.18 |
fsXPAD OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.10.22 |
fsXPADDefTable SEQUENCE OF FsXPADDefEntry .1.3.6.1.4.1.635.1.2.1.10.22.1 |
fsXPADDefEntry FsXPADDefEntry .1.3.6.1.4.1.635.1.2.1.10.22.1.1 |
fsXPADPortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.1.1.1 |
fsXPADX3SpeedThis object specifies the baudrate at which the PAD
operates the link between the PAD and the TTY. Note that
this object may only be read.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.1.1.2 |
fsXPADDataBitsrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.1.1.3 |
fsXPADStopBitsrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.1.1.4 |
fsXPADFlowControlrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.1.1.5 |
fsXPADFlowConTyperw Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.1.1.6 |
fsXPADSubAddrSub Address .rw DisplayString .1.3.6.1.4.1.635.1.2.1.10.22.1.1.7 |
fsXPADAllowMnemonicsThis boolean object specifies whether or not the use of
Mnemonics is permissible at the PAD port.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.1.1.8 |
fsXPADIdleVCTmrThis object specifies the maximum duration in minutes for which
an SVC on the PAD port may be allowed to remain idle. A value
of zero indicates the VC may be allowed to remain idle forever.
This timer is in seconds.
The default value is 180.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.22.1.1.9 |
fsXPADX3ProfileSelectThis is an index into the padX3ProfileTable the entries
within which are to be the default X.3 paramaters for the
PAD port.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.1.1.10 |
fsXPADTelLogPortro Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.1.1.11 |
fsXPADStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.1.1.12 |
fsXPADProfile1DefTable SEQUENCE OF FsXPADProfile1Entry .1.3.6.1.4.1.635.1.2.1.10.22.2 |
fsXPADProfile1Entry FsXPADProfile1Entry .1.3.6.1.4.1.635.1.2.1.10.22.2.1 |
fsXPADPro1PortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.2.1.1 |
fsXPADX3RecallCharThis object specifies the value of the PAD Recall character
which allows the TTY to initiate an escape from the 'data
transfer' state or the 'connection in progress' state to
send 'PAD Command signals'. This object may take one of
the following values:
- 0 Not possible
- 1 Character DLE
- 32 to 126 The graphic character corresponding
to the value.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.22.2.1.2 |
fsXPADX3EchoEnableThis object specifies whether the character received from
the TTY is transmitted back (apart from being interpreted
by the PAD).rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.2.1.3 |
fsXPADX3DataFwdCharThis object defines the sets of character(s) received from
the TTY that are to recognised by the PAD as an indication
to complete the assembly and forward a 'complete packet
sequence' as defined in <>.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.2.1.4 |
fsXPADX3IdleTmrThis object defines the duration of an interval between
successive characters received from the TTY, which, when
exceeded, will cause the PAD to terminate the assembly of
a packet and forward the same.
This timer is in 20th of a second.
The default value is 0.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.22.2.1.5 |
fsXPADX3ANCDevCtrlThis object allows for flow control between the PAD and the
TTY. If this is set to 'dxfer', flow control is enabled
only in the 'data transfer' state. The other permissible
values are self-explanatory.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.2.1.6 |
fsXPADX3PSSCtrlThis object specifies whether or not and in what format
PAD Service signals are transmitted.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.2.1.7 |
fsXPADX3ActOnBreakThis object determines the action to be initiated by the
PAD upon receipt of a break signal from the TTY.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.2.1.8 |
fsXPADX3DiscardOutputThis object provides for the PAD to discard the content of
user sequences in packets upon request rather than
disassembling and transmitting these to the TTY.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.2.1.9 |
fsXPADX3CRPaddingThis object provides for the automatic insertion by the PAD
of padding characters in the character stream transmitted
to the TTY after the occurence of a 'carriage return`.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.22.2.1.10 |
fsXPADX3LineFoldingThis object provides for the automatic insertion by the PAD
of appropriate format effectors in the character stream
transmitted to the TTY. In other words, this object
specifies the maxmimum number of graphic characters that
may be present in a line.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.22.2.1.11 |
fsXPADPro1Statusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.2.1.12 |
fsXPADProfile2DefTable SEQUENCE OF FsXPADProfile2Entry .1.3.6.1.4.1.635.1.2.1.10.22.3 |
fsXPADProfile2Entry FsXPADProfile2Entry .1.3.6.1.4.1.635.1.2.1.10.22.3.1 |
fsXPADPro2PortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.3.1.1 |
fsXPADX3FlowCtrlThis object determines whether or not flow control is
enabled between the TTY and the PAD.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.3.1.2 |
fsXPADX3LFAfterCRThis object provides for the automatic insertion by the PAD
of a linefeed (LF) character in the character stream to or
from the TTY after the occurence of each carriage return
(CR) character. This is applicable only in the 'data
transfer' state.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.22.3.1.3 |
fsXPADX3LFPaddingThis object provides for the automatic insertion by the PAD
of padding character(s) in the character stream transmitted
to the TTY after the occurence of an LF character. This is
applicable only in the 'data transfer' state.rw INTEGER .1.3.6.1.4.1.635.1.2.1.10.22.3.1.4 |
fsXPADX3EditingThis object specifies whether or not the character delete,
line delete and the line display editing capabilities are
enabled in the 'data transfer' state.rw Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.3.1.5 |
fsXPADX3CharDelCharrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.22.3.1.6 |
fsXPADX3LineDelCharrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.22.3.1.7 |
fsXPADX3LineDisplayCharrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.22.3.1.8 |
fsXPADX3EditingPSSrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.22.3.1.9 |
fsXPADX3EchoMaskrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.3.1.10 |
fsXPADX3Parityrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.3.1.11 |
fsXPADX3PageWaitrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.22.3.1.12 |
fsXPADPro2Statusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.22.3.1.13 |
fsPPPNew OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.10.23 |
fsPPPNewDefTable SEQUENCE OF FsPPPNewDefEntry .1.3.6.1.4.1.635.1.2.1.10.23.1 |
fsPPPNewDefEntry FsPPPNewDefEntry .1.3.6.1.4.1.635.1.2.1.10.23.1.1 |
fsPPPNewPortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.10.23.1.1.1 |
fsPPPNewTyperw Enumeration .1.3.6.1.4.1.635.1.2.1.10.23.1.1.2 |
fsPPPNewSpeedrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.23.1.1.3 |
fsPPPNewLQMrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.23.1.1.4 |
fsPPPNewLQMPertrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.23.1.1.5 |
fsPPPNewLQMTimerrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.23.1.1.6 |
fsPPPNewIPXNetNumberrw DisplayString .1.3.6.1.4.1.635.1.2.1.10.23.1.1.7 |
fsPPPNewNodeNumberrw DisplayString .1.3.6.1.4.1.635.1.2.1.10.23.1.1.8 |
fsPPPNewSapModerw Enumeration .1.3.6.1.4.1.635.1.2.1.10.23.1.1.9 |
fsPPPNewLCPMRUrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.23.1.1.10 |
fsPPPNewAddrNegoSelrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.23.1.1.11 |
fsPPPNewAddrNegorw IpAddress .1.3.6.1.4.1.635.1.2.1.10.23.1.1.12 |
fsPPPNewLocalUserNamerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.635.1.2.1.10.23.1.1.13 |
fsPPPNewLocalPasswdrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.635.1.2.1.10.23.1.1.14 |
fsPPPNewAuthProtocolrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.23.1.1.15 |
fsPPPNewStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.23.1.1.16 |
fsPPPNewRemoteUserTable SEQUENCE OF FsPPPNewRemoteUserEntry .1.3.6.1.4.1.635.1.2.1.10.23.2 |
fsPPPNewRemoteUserEntry FsPPPNewRemoteUserEntry .1.3.6.1.4.1.635.1.2.1.10.23.2.1 |
fsPPPRemotePortNorw Enumeration .1.3.6.1.4.1.635.1.2.1.10.23.2.1.1 |
fsPPPRemoteIndexrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.23.2.1.2 |
fsPPPRemoteNamerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.635.1.2.1.10.23.2.1.3 |
fsPPPRemotePasswdrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.635.1.2.1.10.23.2.1.4 |
fsPPPRemoteStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.23.2.1.5 |
fsPPPMLink OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.10.24 |
fsPPPMLinkDefTable SEQUENCE OF FsPPPMLinkDefEntry .1.3.6.1.4.1.635.1.2.1.10.24.1 |
fsPPPMLinkDefEntry FsPPPMLinkDefEntry .1.3.6.1.4.1.635.1.2.1.10.24.1.1 |
fsPPPMLinkPortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.10.24.1.1.1 |
fsPPPMLinkIPXNetNumberrw DisplayString .1.3.6.1.4.1.635.1.2.1.10.24.1.1.2 |
fsPPPMLinkNodeNumberrw DisplayString .1.3.6.1.4.1.635.1.2.1.10.24.1.1.3 |
fsPPPMLinkSapModerw Enumeration .1.3.6.1.4.1.635.1.2.1.10.24.1.1.4 |
fsPPPMLinkMRRUrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.24.1.1.5 |
fsPPPMLinkMPHeaderrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.24.1.1.6 |
fsPPPMLinkAddrNegoSelrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.24.1.1.7 |
fsPPPMLinkAddrNegorw IpAddress .1.3.6.1.4.1.635.1.2.1.10.24.1.1.8 |
fsPPPMLinkLocalUserNamerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.635.1.2.1.10.24.1.1.9 |
fsPPPMLinkLocalPasswdrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.635.1.2.1.10.24.1.1.10 |
fsPPPMLinkAuthProtocolrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.24.1.1.11 |
fsPPPMLinkStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.24.1.1.12 |
fsPPPMLinkMemberTable SEQUENCE OF FsPPPMLinkMemberEntry .1.3.6.1.4.1.635.1.2.1.10.24.2 |
fsPPPMLinkMemberEntry FsPPPMLinkMemberEntry .1.3.6.1.4.1.635.1.2.1.10.24.2.1 |
fsPPPMemberPortNorw Enumeration .1.3.6.1.4.1.635.1.2.1.10.24.2.1.1 |
fsPPPMemberIndexrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.24.2.1.2 |
fsPPPMemberPortrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.24.2.1.3 |
fsPPPMemberStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.24.2.1.4 |
fsPPPMLinkRemoteUserTable SEQUENCE OF FsPPPMLinkRemoteUserEntry .1.3.6.1.4.1.635.1.2.1.10.24.3 |
fsPPPMLinkRemoteUserEntry FsPPPMLinkRemoteUserEntry .1.3.6.1.4.1.635.1.2.1.10.24.3.1 |
fsPPPMLRemotePortNorw Enumeration .1.3.6.1.4.1.635.1.2.1.10.24.3.1.1 |
fsPPPMLRemoteIndexrw INTEGER .1.3.6.1.4.1.635.1.2.1.10.24.3.1.2 |
fsPPPMLRemoteNamerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.635.1.2.1.10.24.3.1.3 |
fsPPPMLRemotePasswdrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.635.1.2.1.10.24.3.1.4 |
fsPPPMLRemoteStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.24.3.1.5 |
fsEtherNet OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.10.25 |
fsPortEtherDefinition OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.10.25.1 |
fsPortEtherIPXEncapsrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.25.1.1 |
fsPortEtherNetNumberrw DisplayString .1.3.6.1.4.1.635.1.2.1.10.25.1.2 |
fsPortEtherSmartARPrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.25.1.3 |
fsPortEtherSapModerw Enumeration .1.3.6.1.4.1.635.1.2.1.10.25.1.4 |
fsTokenRing OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.10.26 |
fsPortTokenDefinition OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.10.26.1 |
fsPortTokenSpeedrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.26.1.1 |
fsPortTokenEarlyReleaserw Enumeration .1.3.6.1.4.1.635.1.2.1.10.26.1.2 |
fsPortTokenIPXNetNumrw DisplayString .1.3.6.1.4.1.635.1.2.1.10.26.1.3 |
fsPortTokenIPXEncapsurw Enumeration .1.3.6.1.4.1.635.1.2.1.10.26.1.4 |
fsPortTokenSmartARPrw Enumeration .1.3.6.1.4.1.635.1.2.1.10.26.1.5 |
fsPortTokenSapModerw Enumeration .1.3.6.1.4.1.635.1.2.1.10.26.1.6 |
fsInterfaceDefinition OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.11.1 |
fsInterDefTable SEQUENCE OF FsInterDefEntry .1.3.6.1.4.1.635.1.2.1.11.1.1 |
fsInterDefEntry FsInterDefEntry .1.3.6.1.4.1.635.1.2.1.11.1.1.1 |
fsInterfacePortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.11.1.1.1.1 |
fsInterfaceTyperw Enumeration .1.3.6.1.4.1.635.1.2.1.11.1.1.1.2 |
fsInterfaceDescrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.635.1.2.1.11.1.1.1.3 |
fsInterfaceE1 OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.11.2 |
fsPortE1DefTable SEQUENCE OF FsPortE1DefEntry .1.3.6.1.4.1.635.1.2.1.11.2.1 |
fsPortE1DefEntry FsPortE1DefEntry .1.3.6.1.4.1.635.1.2.1.11.2.1.1 |
fsPortE1PortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.11.2.1.1.1 |
fsPortE1DsuFrameFormatrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.2.1.1.2 |
fsPortE1DsuCRCrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.2.1.1.3 |
fsPortE1LineBuildoutrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.2.1.1.4 |
fsPortE1DsuClockrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.2.1.1.5 |
fsPortE1DsuTimeSlotsrw DisplayString .1.3.6.1.4.1.635.1.2.1.11.2.1.1.6 |
fsPortE1DsuDataTyperw Enumeration .1.3.6.1.4.1.635.1.2.1.11.2.1.1.7 |
fsPortE1DsuDisFramerw Enumeration .1.3.6.1.4.1.635.1.2.1.11.2.1.1.8 |
fsPortE1DsuAISTransrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.2.1.1.9 |
fsPortE1DsuLineLooprw Enumeration .1.3.6.1.4.1.635.1.2.1.11.2.1.1.10 |
fsPortE1ChannelModerw Enumeration .1.3.6.1.4.1.635.1.2.1.11.2.1.1.11 |
fsPortE1Channel64KRaterw DisplayString .1.3.6.1.4.1.635.1.2.1.11.2.1.1.12 |
fsPortE1Channel56KRaterw DisplayString .1.3.6.1.4.1.635.1.2.1.11.2.1.1.13 |
fsPortE1Channel48KRaterw DisplayString .1.3.6.1.4.1.635.1.2.1.11.2.1.1.14 |
fsPortE1ConfigStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.2.1.1.15 |
fsInterfaceT1 OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.11.3 |
fsPortT1DefTable SEQUENCE OF FsPortT1DefEntry .1.3.6.1.4.1.635.1.2.1.11.3.1 |
fsPortT1DefEntry FsPortT1DefEntry .1.3.6.1.4.1.635.1.2.1.11.3.1.1 |
fsPortT1PortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.11.3.1.1.1 |
fsPortT1DsuFrameFormatrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.3.1.1.2 |
fsPortT1DsuLineCoderw Enumeration .1.3.6.1.4.1.635.1.2.1.11.3.1.1.3 |
fsPortT1DsuBitStuffingrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.3.1.1.4 |
fsPortT1DsuLineBuildOutrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.3.1.1.5 |
fsPortT1DsuGSTACKLineBuildOutrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.3.1.1.6 |
fsPortT1DsuClockrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.3.1.1.7 |
fsPortT1DsuLineLoopBackrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.3.1.1.8 |
fsPortT1DsuLocAnalogrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.3.1.1.9 |
fsPortT1DsuLocDigitalrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.3.1.1.10 |
fsPortT1DsuRemAnalogrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.3.1.1.11 |
fsPortT1DsuRemDigitalrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.3.1.1.12 |
fsPortT1DsuTimeSlotDataRaterw Enumeration .1.3.6.1.4.1.635.1.2.1.11.3.1.1.13 |
fsPortT1DsuTimeSlotsrw DisplayString .1.3.6.1.4.1.635.1.2.1.11.3.1.1.14 |
fsPortT1DsuTimeSlotDataTyperw Enumeration .1.3.6.1.4.1.635.1.2.1.11.3.1.1.15 |
fsPortT1DsuYellowAlarmrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.3.1.1.16 |
fsPortT1ChannelModerw Enumeration .1.3.6.1.4.1.635.1.2.1.11.3.1.1.17 |
fsPortT1Channel64KRaterw DisplayString .1.3.6.1.4.1.635.1.2.1.11.3.1.1.18 |
fsPortT1Channel56KRaterw DisplayString .1.3.6.1.4.1.635.1.2.1.11.3.1.1.19 |
fsPortT1Channel48KRaterw DisplayString .1.3.6.1.4.1.635.1.2.1.11.3.1.1.20 |
fsPortT1ConfigStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.3.1.1.21 |
fsInterfaceVoice OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.11.4 |
fsPortVoiceE1LineBuildOutrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.4.1 |
fsPortVoiceE1Clockrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.4.2 |
fsPortVoiceE1SeizeABCDrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.635.1.2.1.11.4.3 |
fsPortVoiceE1IdleABCDrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.635.1.2.1.11.4.4 |
fsPortVoiceT1FrameFormatrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.4.5 |
fsPortVoiceT1LineCoderw Enumeration .1.3.6.1.4.1.635.1.2.1.11.4.6 |
fsPortVoiceT1LineBuildOutrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.4.7 |
fsPortVoiceT1Clockrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.4.8 |
fsPortVoiceT1SeizeABCDrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.635.1.2.1.11.4.9 |
fsPortVoiceT1IdleABCDrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.635.1.2.1.11.4.10 |
fsPortVoiceTeleSignalrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.4.11 |
fsPortVoiceEMTyperw Enumeration .1.3.6.1.4.1.635.1.2.1.11.4.12 |
fsPortVoiceEMWirerw Enumeration .1.3.6.1.4.1.635.1.2.1.11.4.13 |
fsInterfaceSerial OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.11.5 |
fsPortSerialDefTable SEQUENCE OF FsPortSerialDefEntry .1.3.6.1.4.1.635.1.2.1.11.5.1 |
fsPortSerialDefEntry FsPortSerialDefEntry .1.3.6.1.4.1.635.1.2.1.11.5.1.1 |
fsPortSerialPortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.11.5.1.1.1 |
fsPortSerialDteDceModerw Enumeration .1.3.6.1.4.1.635.1.2.1.11.5.1.1.2 |
fsPortSerialConfigStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.5.1.1.3 |
fsInterfaceSDSL OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.11.6 |
fsPortSDSLTerminalTyperw Enumeration .1.3.6.1.4.1.635.1.2.1.11.6.1 |
fsPortSDSLDataRaterw Enumeration .1.3.6.1.4.1.635.1.2.1.11.6.2 |
fsPortSDSLAnalogAGCrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.6.3 |
fsPortSDSLSeqSourcerw Enumeration .1.3.6.1.4.1.635.1.2.1.11.6.4 |
fsPortSDSLTranScramblerrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.6.5 |
fsPortSDSLRecDeScramblerrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.6.6 |
fsPortSDSLEchoCancellerrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.6.7 |
fsPortSDSLRemoteBitpumprw Enumeration .1.3.6.1.4.1.635.1.2.1.11.6.8 |
fsPortSDSLTestModesrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.6.9 |
fsInterfaceDT1E1 OBJECT IDENTIFIER .1.3.6.1.4.1.635.1.2.1.11.7 |
fsPortDT1E1ConfigTable SEQUENCE OF FsPortDT1E1ConfigEntry .1.3.6.1.4.1.635.1.2.1.11.7.1 |
fsPortDT1E1ConfigEntry FsPortDT1E1ConfigEntry .1.3.6.1.4.1.635.1.2.1.11.7.1.1 |
fsPortDT1E1ConfigPortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.11.7.1.1.1 |
fsPortDT1E1ConfigPort1LineBuildoutrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.7.1.1.2 |
fsPortDT1E1ConfigPort2LineBuildoutrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.7.1.1.3 |
fsPortDT1E1ConfigPort1Clockrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.7.1.1.4 |
fsPortDT1E1ConfigPort2Clockrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.7.1.1.5 |
fsPortDT1E1ConfigPort1TimeSlotrw DisplayString .1.3.6.1.4.1.635.1.2.1.11.7.1.1.6 |
fsPortDT1E1ConfigPort2TimeSlotrw DisplayString .1.3.6.1.4.1.635.1.2.1.11.7.1.1.7 |
fsPortDT1E1ConfigPortTyperw Enumeration .1.3.6.1.4.1.635.1.2.1.11.7.1.1.8 |
fsPortDT1E1ConfigChannelModerw Enumeration .1.3.6.1.4.1.635.1.2.1.11.7.1.1.9 |
fsPortDT1E1ConfigChannel64KRaterw DisplayString .1.3.6.1.4.1.635.1.2.1.11.7.1.1.10 |
fsPortDT1E1ConfigChannel56KRaterw DisplayString .1.3.6.1.4.1.635.1.2.1.11.7.1.1.11 |
fsPortDT1E1ConfigChannel48KRaterw DisplayString .1.3.6.1.4.1.635.1.2.1.11.7.1.1.12 |
fsPortDT1E1ConfigTimingRefrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.7.1.1.13 |
fsPortDT1E1ConfigTDMClockRaterw Enumeration .1.3.6.1.4.1.635.1.2.1.11.7.1.1.14 |
fsPortDT1E1ConfigStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.7.1.1.15 |
fsPortDT1E1ConfigPort1IdleABCDBitsrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.635.1.2.1.11.7.1.1.16 |
fsPortDT1E1ConfigPort2IdleABCDBitsrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.635.1.2.1.11.7.1.1.17 |
fsPortDT1E1ConfigPort1SeizeABCDBitsrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.635.1.2.1.11.7.1.1.18 |
fsPortDT1E1ConfigPort2SeizeABCDBitsrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.635.1.2.1.11.7.1.1.19 |
fsPortDT1E1CrossConnTable SEQUENCE OF FsPortDT1E1CrossConnEntry .1.3.6.1.4.1.635.1.2.1.11.7.2 |
fsPortDT1E1CrossConnEntry FsPortDT1E1CrossConnEntry .1.3.6.1.4.1.635.1.2.1.11.7.2.1 |
fsPortDT1E1CrossConnPortNoro Enumeration .1.3.6.1.4.1.635.1.2.1.11.7.2.1.1 |
fsPortDT1E1CrossConnSys-Port1rw DisplayString .1.3.6.1.4.1.635.1.2.1.11.7.2.1.2 |
fsPortDT1E1CrossConnSys-Port2rw DisplayString .1.3.6.1.4.1.635.1.2.1.11.7.2.1.3 |
fsPortDT1E1CrossConnPort1-Sysrw DisplayString .1.3.6.1.4.1.635.1.2.1.11.7.2.1.4 |
fsPortDT1E1CrossConnPort1-Port2rw DisplayString .1.3.6.1.4.1.635.1.2.1.11.7.2.1.5 |
fsPortDT1E1CrossConnPort2-Sysrw DisplayString .1.3.6.1.4.1.635.1.2.1.11.7.2.1.6 |
fsPortDT1E1CrossConnPort2-Port1rw DisplayString .1.3.6.1.4.1.635.1.2.1.11.7.2.1.7 |
fsPortDT1E1CrossConnStatusrw Enumeration .1.3.6.1.4.1.635.1.2.1.11.7.2.1.8 |