EDGELINK-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
103
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
103 total| Object Name |
|---|
telco OBJECT IDENTIFIER .1.3.6.1.4.1.564 |
RFC-1215 Unknown .1.3.6.1.4.1.564 |
edgeLink OBJECT IDENTIFIER .1.3.6.1.4.1.564.101 |
elM13v1 OBJECT IDENTIFIER .1.3.6.1.4.1.564.101.1 |
edgeLinkEventThis trap is sent when an alarm event is set or cleard. TRAP-TYPE .1.3.6.1.4.1.564.101.1.0.1 |
elDS1CM OBJECT IDENTIFIER .1.3.6.1.4.1.564.101.1.1 |
elDS1CMTableDS1 Configuration Management table. SEQUENCE OF ElDS1CMEntry .1.3.6.1.4.1.564.101.1.1.1 |
elDS1CMEntryDS1 Configuration Management table entry. ElDS1CMEntry .1.3.6.1.4.1.564.101.1.1.1.1 |
elDS1CMChannelNumberTable index, the DS1 channel number.ro INTEGER .1.3.6.1.4.1.564.101.1.1.1.1.1 |
elDS1CMLineCodeSelect DS1 line code for the channel number selected
by this tables index.rw Enumeration .1.3.6.1.4.1.564.101.1.1.1.1.2 |
elDS1CMLineBuildoutSelect line build-out for the DS1 line selected by this
tables index:, 0 to 133 ft, or 133 to 266 ft, 266 to 399 ft,
399 to 533 ft, or 533 to 655 ft.rw Enumeration .1.3.6.1.4.1.564.101.1.1.1.1.3 |
elDS1CMLoopbackModeSet the DS1 loopback mode to Line, terminal, remote, or
none. In M13 Mode, issuing a DS1 Remote Terminal Lpbk
will cause any previous Remote DS1 Terminal Lpbk(s) to be
Dropped.rw Enumeration .1.3.6.1.4.1.564.101.1.1.1.1.4 |
elDS1CMServiceModeSet the DS1 service mode for the channel indicated to
in-service or out-of-service. Certain service effecting
operations can not be initiated unless the DS1 channel
is placed out-of-service.rw Enumeration .1.3.6.1.4.1.564.101.1.1.1.1.5 |
elDS1CMInterfaceEquippedDS1 Interfaces may be 'equipped' or 'unequipped'. No PM
or FM operations will occur on an unequipped interface.
Access is allowed to MIB variables which correspond
to unequipped interfaces, although PM and FM values
will be zeros. When the DS1 interface is Disaled an AIS
will be sent on the channel.rw Enumeration .1.3.6.1.4.1.564.101.1.1.1.1.6 |
elDS1CMChannelNameA ChannelName can be assigned for each DS1 channel. The
Channel name cannot be more than 10 characters.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.564.101.1.1.1.1.7 |
elDS1CMInputStatusReports the input State of the DS1 channel indexed by
Channel Number.ro Enumeration .1.3.6.1.4.1.564.101.1.1.1.1.8 |
elDS1CMMaskStateGet the state of the DS1 Channel identified by the index.
The Mask state identifies the Autosense State of the DS1 Channel.ro Enumeration .1.3.6.1.4.1.564.101.1.1.1.1.9 |
elDS1CMInterfaceRescanRescan the DS1 Channel identified by the index.rw Enumeration .1.3.6.1.4.1.564.101.1.1.1.1.10 |
elALLDS1CMLineCodeSet DS1 line code for all DS1 channels. A value
Inderminate(3) will be returned if All the DS1 Channels
are not set to either ds1LineCodeAMI or ds1LineCodeB8ZS.rw Enumeration .1.3.6.1.4.1.564.101.1.1.2 |
elALLDS1CMLineBuildoutSelect line build-out for All the DS1 lines to
0 to 133 ft, or 133 to 266 ft, 266 to 399 ft,
399 to 533 ft, or 533 to 655 ft.rw Enumeration .1.3.6.1.4.1.564.101.1.1.3 |
elALLDS1CMLoopbackModeSet the DS1 loopback mode to Line, Terminal, Remote, or
None for All the DS1 Channels. In M13 Mode, issuing a
DS1 Remote Terminal Lpbk will cause any previous Remote
DS1 Terminal Lpbk(s) to be dropped.rw Enumeration .1.3.6.1.4.1.564.101.1.1.4 |
elALLDS1CMServiceModeSet the DS1 service mode for All DS1 channels to
in-service or out-of-service. Certain service effecting
operations can not be initiated unless All the DS1 channels
will be placed out-of-service.rw Enumeration .1.3.6.1.4.1.564.101.1.1.5 |
elALLDS1CMInterfaceEquippedSet All the DS1 Channels to 'equipped' or 'unequipped'
state. No PM or FM operations will occur on an unequipped
DS1 interface. Access is allowed to MIB variables which
correspond to unequipped interfaces, although PM and FM
values will be zeros.rw Enumeration .1.3.6.1.4.1.564.101.1.1.6 |
elCM OBJECT IDENTIFIER .1.3.6.1.4.1.564.101.1.2 |
elCMSystemStatusThis DisplayString gives the summary information about
the Current EdgeLink100 System Status. The Description
includes ...
1) chasisType
2) Active Module
3) Fault LED Status
4) Abnormal LED Status
Fault LED Status is a combined value of the three bits
each representing CRITICAL, MAJOR and MINOR Alarms. The
three LEDS are inside the EL100 Case on the Cards.
0 => No Alarms.
1 => Critical Alarm (001)
2 => Major Alarm (010)
3 => Critical and Major Alarms (011)
4 => Minor Alarm (100)
5 => Minor and Critical Alarms (101)
6 => Minor and Major Alarms (110)
7 => Major Minor and Critical Alarms (111).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.564.101.1.2.1 |
elCMDS3ParityModeSelect C-bit or P-bit parity mode for DS3 interface.
This Object can't be set when ServiceMode is IN-Servicerw Enumeration .1.3.6.1.4.1.564.101.1.2.2 |
elCMDS3LineBuildoutSelect line build-out for DS3 Line, 0 to 100 ft,
100 to 200 ft, or 200-450.This MIB Object can't be set
when ServiceMode is IN-Servicerw Enumeration .1.3.6.1.4.1.564.101.1.2.3 |
elCMDS3TxTimingSelect mode for DS3 transmit timing. This MIB Object
can't be set when ServiceMode is IN-Servicerw Enumeration .1.3.6.1.4.1.564.101.1.2.4 |
elCMProtectionModeIn unprotected mode, switching is prohibited.
While in protected mode, a standing minor alarm will
occur if the off-line card is unavailable or not in
operation. The system can be set to unprotected mode
to turnoff this alarm.
If the off-line card becomes operational while in
unprotected mode, the mode is automatically switched
to protected mode. The user will not be allowed to set
the system to protectedMode.rw Enumeration .1.3.6.1.4.1.564.101.1.2.5 |
elCMCardSelectRead or select choice of on-line card. This operation
will force a switch to occur if the off-line card is
selected.rw Enumeration .1.3.6.1.4.1.564.101.1.2.6 |
elCMClearTooManySwitchesClear switching-disabled state which occurs as
a result of too many switches between the cards in a
protected system in a 10 minute interval.
ClearTooManySwitchesLock command is used to remove the
standing Alarm. On a read, the value indeterminate
will be returned if the SNMP variable was never set to
clearTooManySwitchesLock(2), otherwise
clearTooManySwitchesLock(2) will be returned.rw Enumeration .1.3.6.1.4.1.564.101.1.2.7 |
elCMDS3LoopbackModeSet the DS3 loopback mode to line, terminal,
remote, or none. The System can't be set to
ds3LpbkRemoteFacility when it is in M13 Mode.
The Terminal LoopBack is feasible only when the
elCMDS3TxTiming Object is set to ds3TxTimingLocal.rw Enumeration .1.3.6.1.4.1.564.101.1.2.8 |
elCMDS3ServiceModeSet the DS3 service mode to in-service or
out-of-service. Certain service effecting operations
can not be initiated unless the DS3 channel is placed
out-of-service.rw Enumeration .1.3.6.1.4.1.564.101.1.2.9 |
elCMCurTimeDateRead or set the system real time clock. The string
is in the form MM/DD/YYYY HH:MM:SS.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.564.101.1.2.10 |
elCMBerThresholdSet the BER Threshold value for the system to 10-6,
10-7, 10-8 or 10-9. BerThershold can't changed when
the ServiceMode is IN-Service.rw Enumeration .1.3.6.1.4.1.564.101.1.2.11 |
elCMSystemInfoGets information about the MPU type, board revision,
card revision level, software revision, CLEI code,
MAC address, and Date of manufacture.ro DisplayString .1.3.6.1.4.1.564.101.1.2.12 |
elCMPPPPortBaudRateSpecifies the baud rate on the craft/PPP port when
that port is running PPP (i.e. when carrier detect is asserted).ro Enumeration .1.3.6.1.4.1.564.101.1.2.13 |
elCMIfc OBJECT IDENTIFIER .1.3.6.1.4.1.564.101.1.3 |
elCMRemoteCBitIPAddressThis is the IP address of the partner EdgeLink's
C-bit channel interface. This is used for
partner-to-partner communications. Must be on same
subnet as elCMLocalCBitIPAddress. This IP must be the
same as elCMLocalCBitIPAddress on the partner device.rw IpAddress .1.3.6.1.4.1.564.101.1.3.1 |
elCMLocalCBitIPAddressThis is the IP address of my C-bit channel
interface and is used for partner-to-partner
communications. Must be on same subnet as
elCMRemoteCBitIPAddress. This IP must be the same
as elCMRemoteCBitIPAddress on the partner device.rw IpAddress .1.3.6.1.4.1.564.101.1.3.2 |
elCMCBitIPSubnetMaskSpecifies the subnet address mask for the C-Bit IP
channel.rw IpAddress .1.3.6.1.4.1.564.101.1.3.3 |
elCMRemotePPPIPAddressThis is the IP Address for the Remote Client during
PPP session.rw IpAddress .1.3.6.1.4.1.564.101.1.3.4 |
elCMIfcTableEthernet/PPP Interfaces table. SEQUENCE OF ElCMIfcEntry .1.3.6.1.4.1.564.101.1.3.5 |
elCMIfcEntryEthernet/PPP Interfaces table entry. ElCMIfcEntry .1.3.6.1.4.1.564.101.1.3.5.1 |
elCMIfcInterfaceNumberTable index. The table has one row for each
external IP interface, Ethernet and PPP.ro Enumeration .1.3.6.1.4.1.564.101.1.3.5.1.1 |
elCMIfcMyIPAddrThe IP address for this interface.rw IpAddress .1.3.6.1.4.1.564.101.1.3.5.1.2 |
elCMIfcMyIPSubnetAddrMaskSubnet address mask for this IP address.rw IpAddress .1.3.6.1.4.1.564.101.1.3.5.1.3 |
elCMIfcMyDefaultGatewayAddrDefault gateway address for this interface.
If 0, it will be ignored.rw IpAddress .1.3.6.1.4.1.564.101.1.3.5.1.4 |
elCMIfcTrapSendAddr1Address 1 of 4 to send traps to. If 0, will be ignored.rw IpAddress .1.3.6.1.4.1.564.101.1.3.5.1.5 |
elCMIfcTrapSendAddr2Address 2 of 4 to send traps to. If 0, will be ignored.rw IpAddress .1.3.6.1.4.1.564.101.1.3.5.1.6 |
elCMIfcTrapSendAddr3Address 3 of 4 to send traps to. If 0, will be ignored.rw IpAddress .1.3.6.1.4.1.564.101.1.3.5.1.7 |
elCMIfcTrapSendAddr4Address 4 of 4 to send traps to. If 0, will be ignored.rw IpAddress .1.3.6.1.4.1.564.101.1.3.5.1.8 |
elPM OBJECT IDENTIFIER .1.3.6.1.4.1.564.101.1.4 |
elPMDS3TotalSwitchesNumber of switches which have occurred since startup,
or since last time PM metrics were cleared.ro INTEGER .1.3.6.1.4.1.564.101.1.4.1 |
elPMClearAllPMMetricsClears all Performance Management related metrics
and statistics. On a read, the value indeterminate(1)
will be returned if this variable was never set to
clearAllPMMetrics(2), otherwise clearAllPMMetrics(2)
will be returned.rw Enumeration .1.3.6.1.4.1.564.101.1.4.2 |
elDS1PM OBJECT IDENTIFIER .1.3.6.1.4.1.564.101.1.5 |
elDS1PMTimeElapsedThe number of elapsed seconds in the current interval
of DS1 PM data.ro INTEGER .1.3.6.1.4.1.564.101.1.5.1 |
elDS1PMValidIntervalsThe number of intervals which have elapsed and for
which PM data can read, up to and including 96.ro INTEGER .1.3.6.1.4.1.564.101.1.5.2 |
elDS1PMCur OBJECT IDENTIFIER .1.3.6.1.4.1.564.101.1.6 |
elDS1PMCurTableDS1 current PM metrics table. SEQUENCE OF ElDS1PMCurEntry .1.3.6.1.4.1.564.101.1.6.1 |
elDS1PMCurEntryDS1 current PM metrics table entry. ElDS1PMCurEntry .1.3.6.1.4.1.564.101.1.6.1.1 |
elDS1PMCurChannelNumberTable index. Rows are indexed by DS1 channel.ro INTEGER .1.3.6.1.4.1.564.101.1.6.1.1.1 |
elDS1PMCurLineCodeViolationsNumber of line code violations in the current
15 minute interval.ro INTEGER .1.3.6.1.4.1.564.101.1.6.1.1.2 |
elDS1PMCurErroredSecondsNumber of errored seconds in the current interval.ro INTEGER .1.3.6.1.4.1.564.101.1.6.1.1.3 |
elDS1PMIvl OBJECT IDENTIFIER .1.3.6.1.4.1.564.101.1.7 |
elDS1PMIvlTableDS1 Interval PM metrics table. SEQUENCE OF ElDS1PMIvlEntry .1.3.6.1.4.1.564.101.1.7.1 |
elDS1PMIvlEntryDS1 Interval PM metrics table entry. ElDS1PMIvlEntry .1.3.6.1.4.1.564.101.1.7.1.1 |
elDS1PMIvlChannelNumberPrimary table index, a DS1 channel number.ro INTEGER .1.3.6.1.4.1.564.101.1.7.1.1.1 |
elDS1PMIvlIntervalNumberSecondary table index, the interval number.ro INTEGER .1.3.6.1.4.1.564.101.1.7.1.1.2 |
elDS1PMIvlLineCodeViolationsNumber of line code violations for the channel
specified by elDS1PMIvlChannelNumber and in the interval
indicated by elDS1PMIvlIntervalNumber.ro INTEGER .1.3.6.1.4.1.564.101.1.7.1.1.3 |
elDS1PMIvlErroredSecondsNumber of errored seconds for the channel
specified by elDS1PMIvlChannelNumber and in the interval
indicated by elDS1PMIvlIntervalNumber.ro INTEGER .1.3.6.1.4.1.564.101.1.7.1.1.4 |
elDS1PMTot OBJECT IDENTIFIER .1.3.6.1.4.1.564.101.1.8 |
elDS1PMTotTableDS1 Total PM metrics table. SEQUENCE OF ElDS1PMTotEntry .1.3.6.1.4.1.564.101.1.8.1 |
elDS1PMTotEntryDS1 Total PM metrics table entry. ElDS1PMTotEntry .1.3.6.1.4.1.564.101.1.8.1.1 |
elDS1PMTotChannelNumberTable index, DS1 channel number.ro INTEGER .1.3.6.1.4.1.564.101.1.8.1.1.1 |
elDS1PMTotLineCodeViolationsTotal number of line code violations for the channel
specified by elDS1PMIvlChannelNumber.ro INTEGER .1.3.6.1.4.1.564.101.1.8.1.1.2 |
elDS1PMTotErroredSecondsTotal number of errored seconds for the channel
specified by elDS1PMIvlChannelNumber.ro INTEGER .1.3.6.1.4.1.564.101.1.8.1.1.3 |
elFM OBJECT IDENTIFIER .1.3.6.1.4.1.564.101.1.9 |
elFMFillAlarmLogTableTake a snapshot of the alarm log. Must be done before
reading the log into the alarm log table, elFMAlmLogTable.
On a read, the value indeterminate(1) will be returned
if the SNMP variable was never set to fillAlarmLogTable(2),
otherwise fillAlarmLogTable(2) will be returned.rw Enumeration .1.3.6.1.4.1.564.101.1.9.1 |
elFMClearAlarmLogClears the system's alarm log. On a read, the value
indeterminate(1) will be returned if the SNMP variable
was never set to clearAlarmLog(2) otherwise
clearAlarmLog(2) will be returned.rw Enumeration .1.3.6.1.4.1.564.101.1.9.2 |
elFMDS1AutoSenseModeThe AutoSense Mode will be enabled or Disabled on all
the 28 Ds1 channels. The Rescan command will scan all
the equipped DS1 Inputs and update their state.rw Enumeration .1.3.6.1.4.1.564.101.1.9.3 |
elFMDS1InputAlarmModeThis command changes the severity of the DS1 LOS as
either Major alarm or status depending on the selection.rw Enumeration .1.3.6.1.4.1.564.101.1.9.4 |
elFMAlmLog OBJECT IDENTIFIER .1.3.6.1.4.1.564.101.1.10 |
elFMAlmLogTableAlarm log table. This table holds a snapshot of
the alarm log, and is filled by elFMFillAlarmLogTable. SEQUENCE OF ElFMAlmLogEntry .1.3.6.1.4.1.564.101.1.10.1 |
elFMAlmLogEntryAlarm log table entry. ElFMAlmLogEntry .1.3.6.1.4.1.564.101.1.10.1.1 |
elFMAlmLogEntryNumberTable index, between 1 and 100.ro INTEGER .1.3.6.1.4.1.564.101.1.10.1.1.1 |
elFMAlmLogTableAlarmNumberAlarm number.ro INTEGER .1.3.6.1.4.1.564.101.1.10.1.1.2 |
elFMAlmLogTableDescriptionAlarm description.ro DisplayString .1.3.6.1.4.1.564.101.1.10.1.1.3 |
elFMAlmLogTableStatusAlarm status.ro Enumeration .1.3.6.1.4.1.564.101.1.10.1.1.4 |
elFMAlmLogTableTimestampAlarm time stamp in the form mm/dd/yy hh:mm:ss.ro DisplayString .1.3.6.1.4.1.564.101.1.10.1.1.5 |
elFMAlmLogTableChannelChannel associated with the alarm, if any.ro INTEGER .1.3.6.1.4.1.564.101.1.10.1.1.6 |
elFMCurAlm OBJECT IDENTIFIER .1.3.6.1.4.1.564.101.1.11 |
elFMCurAlmTableCurrent alarms table. SEQUENCE OF ElFMCurAlmEntry .1.3.6.1.4.1.564.101.1.11.1 |
elFMCurAlmEntryCurrent alarms table entry. ElFMCurAlmEntry .1.3.6.1.4.1.564.101.1.11.1.1 |
elFMCurAlmTableAlarmNumberPrimary table index, an alarm number.ro INTEGER .1.3.6.1.4.1.564.101.1.11.1.1.1 |
elFMCurAlmTableChannelSecondary table index. Channel associated with
the alarm, can be 0 if channel number is
irrelevant to the alarm.ro INTEGER .1.3.6.1.4.1.564.101.1.11.1.1.2 |
elFMCurAlmTableDescriptionAlarm description.ro DisplayString .1.3.6.1.4.1.564.101.1.11.1.1.3 |
elFMTrapFields OBJECT IDENTIFIER .1.3.6.1.4.1.564.101.1.12 |
elFMTrapAlarmNumberAlarm number associated with the last sent trap.ro INTEGER .1.3.6.1.4.1.564.101.1.12.1 |
elFMTrapAlarmTextAlarm text associated with the last sent trap.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.564.101.1.12.2 |
elFMTrapTimeStampTime stamp associated with the last sent trap.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.564.101.1.12.3 |
elFMTrapAlarmStatusAlarm status associated with the last sent trap.ro INTEGER .1.3.6.1.4.1.564.101.1.12.4 |
elFMTrapChannelNumberChannel number associated with the last sent trap, if any.ro INTEGER .1.3.6.1.4.1.564.101.1.12.5 |