DPT-SCSI-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
192
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
192 total| Object Name |
|---|
dpt OBJECT IDENTIFIER .1.3.6.1.4.1.1597 |
RFC1155-SMI Unknown .1.3.6.1.4.1.1597 |
dptOtherTrapController event generated with a value dptScsiEventInfo. TRAP-TYPE .1.3.6.1.4.1.1597.0.14 |
dptHbaVoltageNormalTrap5V Voltage has returned to the normal range. TRAP-TYPE .1.3.6.1.4.1.1597.0.100 |
dptHbaTemperatureNormalTrapTemperature on controller has returned to normal range. TRAP-TYPE .1.3.6.1.4.1.1597.0.101 |
dptHbaEccRAMErrorNotFoundTrapController detected an ECC RAM Error but an ECC error was not
found when correction was attempted. TRAP-TYPE .1.3.6.1.4.1.1597.0.102 |
dptDevStatusChangedTrapStatus of the device changed. TRAP-TYPE .1.3.6.1.4.1.1597.0.103 |
dptDevReqSenseTrapRequest sense information received from controller. TRAP-TYPE .1.3.6.1.4.1.1597.0.104 |
dptArrayChangeTrapThe software has asked the FW to do an array change. TRAP-TYPE .1.3.6.1.4.1.1597.0.105 |
dptBatteryChangeTrapThe status of the recharchable battery has changed. TRAP-TYPE .1.3.6.1.4.1.1597.0.106 |
dptHbaAuxVoltageNormalTrapAn auxiliary voltage has returned to the normal range. TRAP-TYPE .1.3.6.1.4.1.1597.0.107 |
dptHbaEccRAMErrorCorrectedTrapThe controller detected and corrected an ECC RAM error.
dptScsiHbaBadMemoryAddress contains the RAM address. TRAP-TYPE .1.3.6.1.4.1.1597.0.200 |
dptDevBlockReassignedTrapController reassigned a block. dptScsiDevBadBlockNumber
contains the reassigned block number. TRAP-TYPE .1.3.6.1.4.1.1597.0.201 |
dptDevReqSenseErrorTrapWarning: request sense information from controller. TRAP-TYPE .1.3.6.1.4.1.1597.0.202 |
dptHbaVoltageChangeTrapController detected 5V voltage is outside of the normal range. TRAP-TYPE .1.3.6.1.4.1.1597.0.300 |
dptHbaTemperatureHighTrapHigh temperature detected on controller. TRAP-TYPE .1.3.6.1.4.1.1597.0.301 |
dptHbaEccRAMErrorUncorrectableTrapThe controller detected and uncorrectable ECC RAM error.
dptScsiHbaBadMemoryAddress contains the RAM address. TRAP-TYPE .1.3.6.1.4.1.1597.0.302 |
dptArrayStatusChangeDegradedTrapArray Degraded due to drive failure. TRAP-TYPE .1.3.6.1.4.1.1597.0.303 |
dptDevReqSenseSeriousErrorTrapSerious: request sense information from controller. TRAP-TYPE .1.3.6.1.4.1.1597.0.304 |
dptDevArrayDataInconsistencyTrapArray Data consistency error detected on controller. TRAP-TYPE .1.3.6.1.4.1.1597.0.305 |
dptHbaErrorTrapThe controller has detected a non-SCSI related error, as defined in the I2O spec. TRAP-TYPE .1.3.6.1.4.1.1597.0.306 |
dptDevFailedTrapAn unprotected drive has failed (visible to the OS). TRAP-TYPE .1.3.6.1.4.1.1597.0.307 |
dptDevSmartFailedTrapA drive has reported a SMART failure. TRAP-TYPE .1.3.6.1.4.1.1597.0.308 |
dptHbaAuxVoltageChangeTrapController detected an auxiliary voltage is outside of the
normal range. TRAP-TYPE .1.3.6.1.4.1.1597.0.309 |
dptHbaTemperatureVeryHighTrapVery high temperature detected on controller. TRAP-TYPE .1.3.6.1.4.1.1597.0.400 |
dptArrayStatusChangeFailedTrapArray Failed due to multiple drive failures. TRAP-TYPE .1.3.6.1.4.1.1597.0.401 |
dptScsi OBJECT IDENTIFIER .1.3.6.1.4.1.1597.1 |
dptScsiSys OBJECT IDENTIFIER .1.3.6.1.4.1.1597.1.1 |
dptScsiSysRevLevelDPT SCSI system SNMP agent revision information.ro DptSignature .1.3.6.1.4.1.1597.1.1.1 |
dptScsiSysEngineSignatureDPT signature for the DPT engine. This contains information
on engine version and creation date/time.ro DptSignature .1.3.6.1.4.1.1597.1.1.2 |
dptScsiSysDriverSignatureDPT signature for the driver currently in use by the SNMP
agent. This contains information on driver version and
creation date/time.ro DptSignature .1.3.6.1.4.1.1597.1.1.3 |
dptScsiSysEventLoggerSignatureDPT signature for the event logger/broadcaster currently in
use by the SNMP agent. This contains information
on event logger/broadcaster version and creation date/time.ro DptSignature .1.3.6.1.4.1.1597.1.1.4 |
dptScsiSysMibRevMajorThe Major Revision level.
A change in the major revision level represents a major change
in the architecture of the MIB. A change in the major revision
level may indicate a significant change in the information
supported and/or the meaning of the supported information,
correct interpretation of data may require a MIB document with
the same major revision level.ro INTEGER .1.3.6.1.4.1.1597.1.1.5 |
dptScsiSysMibRevMinorThe Minor Revision level.
A change in the minor revision level may represent some minor
additional support; no changes to any pre-existing information
has occurred.ro INTEGER .1.3.6.1.4.1.1597.1.1.6 |
dptScsiHba OBJECT IDENTIFIER .1.3.6.1.4.1.1597.1.2 |
dptScsiHbaTableA list of RAID controllers managed by the DPT SCSI system. SEQUENCE OF DptScsiHbaEntry .1.3.6.1.4.1.1597.1.2.1 |
dptScsiHbaEntryA set of parameters that describe/control a DPT RAID controller.
See 'SmartRAID User's Manual' for detailed explanation of
the parameters. DptScsiHbaEntry .1.3.6.1.4.1.1597.1.2.1.1 |
dptScsiHbaNumberAn index that uniquely identifies a row in dptHbaTable
that pertains to a particular controller. The value of
this object is the logical device identifier for a DPT
controller. As controllers are detected, they are
assigned numbers incrementally, starting with 0.ro INTEGER .1.3.6.1.4.1.1597.1.2.1.1.1 |
dptScsiHbaVendorThe name of the vendor of the controller.ro DisplayString .1.3.6.1.4.1.1597.1.2.1.1.2 |
dptScsiHbaModelThe controller model identifier.ro DisplayString .1.3.6.1.4.1.1597.1.2.1.1.3 |
dptScsiHbaFirmwareThe controller firmware version.ro DisplayString .1.3.6.1.4.1.1597.1.2.1.1.4 |
dptScsiHbaSerialNumberThe controller serial number.ro DisplayString .1.3.6.1.4.1.1597.1.2.1.1.5 |
dptScsiHbaAddressThe controller Address (normally displayed in hex.)
It is a 32-bit value representing the memory address
used by the controllerro INTEGER (0..'FFFFFFFF'h) .1.3.6.1.4.1.1597.1.2.1.1.6 |
dptScsiHbaHostBusTypeThe type of host computer system bus this controller is
attached to.ro HostBusType .1.3.6.1.4.1.1597.1.2.1.1.7 |
dptScsiHbaHostBusMaxTransferRateThe maximum possible transfer rate on the host bus in MB/s.ro INTEGER .1.3.6.1.4.1.1597.1.2.1.1.8 |
dptScsiHbaIrqThe controller interrupt level.ro INTEGER .1.3.6.1.4.1.1597.1.2.1.1.9 |
dptScsiHbaIrqTypeThe controller interrupt type (Edge or Level).ro IrqType .1.3.6.1.4.1.1597.1.2.1.1.10 |
dptScsiHbaDrqThe controller DMA channel. This object is only applicable for
ISA controllers. Its value is 'notApplicable' for the other
types of controllers.rodeprecated DrqNumber .1.3.6.1.4.1.1597.1.2.1.1.11 |
dptScsiHbaRaidModuleController RAID module type: SmartRAID Millennium controllers
support all RAID levels without the addition of a RAID Module.
These controllers will show 'Embedded' for this object.
SmartRAID Decade and Century controllers support RAID 0 and
RAID 1 by default. RAID 5 support is added by attaching an
RA40x0 RAID Accelerator module to the controller. If one is
attached it will be indicated in this object.ro RaidModule .1.3.6.1.4.1.1597.1.2.1.1.12 |
dptScsiHbaCachingModuleThe controller caching module. 'Embedded' means
that the disk array function is built inside the controller
(SmartRAID products.)rodeprecated CachingModule .1.3.6.1.4.1.1597.1.2.1.1.13 |
dptScsiHbaAudibleAlarmOnThis returns the current status of the controller alarm.ro YesNoStatus .1.3.6.1.4.1.1597.1.2.1.1.14 |
dptScsiHbaUpTimeTime elapsed (in hundredths of a second) since the
controller was last booted.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.1597.1.2.1.1.15 |
dptScsiHbaEccEnabledThis indicates whether or not the controller is using
DPT ECC memory. 'Yes' means that the installed memory
is DPT ECC memory and full ECC protection is active.ro YesNoStatus .1.3.6.1.4.1.1597.1.2.1.1.16 |
dptScsiHbaBackgroundTaskPriorityThis object controls the priority of array background tasks
such as Build, Rebuild and Verify for this controller.
The values range from 1 to 10. A value of 1 is the slowest but
uses the least amount of the controller's bandwidth. While a
value of 10 is the fastest but it uses the most bandwidth.
If operations take too long then increase the value for this
object. If the system runs too slow when these tasks are active,
then decrease the value for this object.ro INTEGER .1.3.6.1.4.1.1597.1.2.1.1.17 |
dptScsiHbaExclusionPeriodEnabledController exclution period is the time span during which it
devotes 100% of its time fulfilling requests for data
reads/writes and zero percent on background activities like
build/rebuild of arrays.
Setting this object to true sets the exclusion period as
defined by dptScsiHbaExclusionPeriodStart and
dptScsiHbaExclusionPeriodEnd objects. Otherwise, if it is set
to false, the exclusion period no effect.rodeprecated YesNoStatus .1.3.6.1.4.1.1597.1.2.1.1.18 |
dptScsiHbaExclusionPeriodStartHour of beginning of the exclusion period. For example, a
value of 0 means that the exclusion starts at 12 a.m.
The maximum duration of an exclusion period can be 24 hours.
Contoller exclution period is the time span during which it
devotes 100% of its time fulfilling requests for data
reads/writes and zero percent on background activities like
build/rebuild of arrays.rodeprecated INTEGER .1.3.6.1.4.1.1597.1.2.1.1.19 |
dptScsiHbaExclusionPeriodEndHour when exclusion period ends. For example, a value of
23 means that the exclusion ends at 11 p.m.
The maximum duration of an exclusion period can be 24 hours.
If dptScsiHbaExclusionPeriodStart is greater than
dptScsiHbaExclusionPeriodEnd, it means that the exclusions
period extends over the next day.
Contoller exclution period is the time span during which it
devotes 100% of its time fulfilling requests for data
reads/writes and zero percent on background activities like
build/rebuild of arrays.rodeprecated INTEGER .1.3.6.1.4.1.1597.1.2.1.1.20 |
dptScsiHbaMaxReadAheadPercentageMax percentage of contoller cache RAM devoted to read-ahead
pages. This value is not applicable to SmartRAID V and later
controllers. For these controllers, this value will be set
to 30.rodeprecated INTEGER .1.3.6.1.4.1.1597.1.2.1.1.21 |
dptScsiHbaMaxDirtyPagesPercentageMax percentage of controller cache RAM that may contain dirty
pages. This value is not applicable to SmartRAID V and later
controllers. For these controllers, this value will be set to
80.rodeprecated INTEGER .1.3.6.1.4.1.1597.1.2.1.1.22 |
dptScsiHbaWriteBackDelayWrite-back delay in milliseconds. This value is not applicable
to SmartRAID V and later controllers. For these controllers,
this value will be set to 250.rodeprecated INTEGER .1.3.6.1.4.1.1597.1.2.1.1.23 |
dptScsiHbaTemperatureTemperature status reported by the controller.ro LowHighStatus .1.3.6.1.4.1.1597.1.2.1.1.24 |
dptScsiHbaVoltage5V voltage status reported by the controller.ro LowHighStatus .1.3.6.1.4.1.1597.1.2.1.1.25 |
dptScsiHbaBadMemoryAddressIf the controller detects a cache RAM error, the address of
the most recent error is stored here. Otherwise it indicates
that no errors have been detected.
Valid RAM addresses are from 1 to 0xffffffff.ro INTEGER (0..'FFFFFFFF'h) .1.3.6.1.4.1.1597.1.2.1.1.26 |
dptScsiHbaBatteryModuleThe Battery Backup Module preserves all controller cache and local
memory contents in the event of power loss to the systemro BatteryBackupModule .1.3.6.1.4.1.1597.1.2.1.1.27 |
dptScsiHbaBatteryStatusBattery status reported by the controller.ro BatteryStatus .1.3.6.1.4.1.1597.1.2.1.1.28 |
dptScsiHbaHighestBusWithDevicesThe bus number of the highest numbered bus on this controller
which has devices currently attached to it.ro INTEGER .1.3.6.1.4.1.1597.1.2.1.1.29 |
dptScsiHbaGeneralStatusGeneral controller status. The following are
the possible values:
ok - the controller and all components attached to
it, such as disks and arrays, are OK.
fail - a component attached to the controller is not OK.
error - the agent cannot get status from the controller.ro HbaGenStatus .1.3.6.1.4.1.1597.1.2.1.1.30 |
dptScsiHbaSmorSignatureThe controller S.M.O.R. revision information. Not available for
SmartRAID IV and earlier controllers.ro DptSignature .1.3.6.1.4.1.1597.1.2.1.1.31 |
dptScsiHbaBiosSignatureThe controller B.I.O.S. revision information. Not available for
SmartRAID IV and earlier controllers.ro DptSignature .1.3.6.1.4.1.1597.1.2.1.1.32 |
dptScsiHbaNvramLayoutThe controller NVRAM layout revision.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1597.1.2.1.1.33 |
dptScsiHbaCacheSocketTableA list of the cache memory module sockets on the controller. SEQUENCE OF DptScsiHbaCacheSocketEntry .1.3.6.1.4.1.1597.1.2.2 |
dptScsiHbaCacheSocketEntryThese parameters describe the cache memory module sockets
on a controller. DptScsiHbaCacheSocketEntry .1.3.6.1.4.1.1597.1.2.2.1 |
dptScsiHbaCacheSocketNumberA controller can have up to 4 cache sockets. This is the
index in the table of cache memory module sockets.ro INTEGER .1.3.6.1.4.1.1597.1.2.2.1.1 |
dptScsiHbaCacheModuleTypeType of a cache memory module.ro MemoryBankType .1.3.6.1.4.1.1597.1.2.2.1.2 |
dptScsiHbaCacheModuleSizeSize of a cache memory module.ro MemoryBankSize .1.3.6.1.4.1.1597.1.2.2.1.3 |
dptScsiBus OBJECT IDENTIFIER .1.3.6.1.4.1.1597.1.3 |
dptScsiBusTableA list of the SCSI buses on a system. SEQUENCE OF DptScsiBusEntry .1.3.6.1.4.1.1597.1.3.1 |
dptScsiBusEntryThese parameters describe/control a SCSI Bus. The entry
is indexed by dptScsiHbaNumber and dptScsiBusNumber.
dptScsiHbaNumber determines to which controller the SCSI bus
belongs and dptScsiBusNumber to which SCSI bus. DptScsiBusEntry .1.3.6.1.4.1.1597.1.3.1.1 |
dptScsiBusNumberAn index that, along with dptScsHbaNumber uniquely,
identifies an entry in the dptScsiBusTable for a
particular SCSI Bus.ro INTEGER .1.3.6.1.4.1.1597.1.3.1.1.1 |
dptScsiBusWidthThe SCSI Bus width.ro BusWidth .1.3.6.1.4.1.1597.1.3.1.1.2 |
dptScsiBusTypeThe SCSI Bus transceiver type.ro ScsiBusType .1.3.6.1.4.1.1597.1.3.1.1.3 |
dptScsiBusMaxTransferRateThe SCSI Bus maximum transfer rate in MB/s.
Valid values are 4, 5, 8, 10, 20, 40, 80, 100, 160, etc.,
depending on the SCSI technology used.ro INTEGER .1.3.6.1.4.1.1597.1.3.1.1.4 |
dptScsiBusHbaScsiIdThe SCSI ID of the controller on this SCSI Bus.ro INTEGER .1.3.6.1.4.1.1597.1.3.1.1.5 |
dptScsiBusHbaTermPowerIndicates the SCSI term-power setting (on/off) for this bus.ro YesNoStatus .1.3.6.1.4.1.1597.1.3.1.1.6 |
dptScsiBusHbaTerminationIndicates the SCSI termination setting for this bus.ro BusTerminationType .1.3.6.1.4.1.1597.1.3.1.1.7 |
dptScsiDev OBJECT IDENTIFIER .1.3.6.1.4.1.1597.1.4 |
dptScsiDevTableA list of SCSI devices managed by the SNMP agent. SEQUENCE OF DptScsiDevEntry .1.3.6.1.4.1.1597.1.4.1 |
dptScsiDevEntryThese parameters describe/control a particular SCSI Device.
The index for this entry is the logical device address of
the SCSI device. The logical device address consists of five
components: contoller number, SCSI bus number, Device ID,
LUN and level. DptScsiDevEntry .1.3.6.1.4.1.1597.1.4.1.1 |
dptScsiDevIdThe SCSI ID of the device.ro INTEGER .1.3.6.1.4.1.1597.1.4.1.1.1 |
dptScsiDevLunThe SCSI LUN (logical unit number) of the device.ro INTEGER .1.3.6.1.4.1.1597.1.4.1.1.2 |
dptScsiDevLevelIndicates the Level of the device.
Level 0 indicates physical devices, while level 1 and 2
indicate logical devices. It also gives its level in the
containment hierarchy of devices.
A device is a logical device if it contains other
SCSI devices, otherwise it is a physical device.
A level 1 array contains only physical devices as its
members; a level 2 device has at least one
level 1 array as a member. A level 2 device would be
a RAID-10 or RAID-50 logical drive.ro INTEGER .1.3.6.1.4.1.1597.1.4.1.1.3 |
dptScsiDevVendorThe name of the vendor of the device.ro DisplayString .1.3.6.1.4.1.1597.1.4.1.1.4 |
dptScsiDevModelThe model name of the device.ro DisplayString .1.3.6.1.4.1.1597.1.4.1.1.5 |
dptScsiDevRevisionThe revision level of the device.ro DisplayString .1.3.6.1.4.1.1597.1.4.1.1.6 |
dptScsiDevSerialNumberThe serial number of the device.ro DisplayString .1.3.6.1.4.1.1597.1.4.1.1.7 |
dptScsiDevStatusThe administrative state of the device. The following are
all the possible values:
invalid - current value is invalid.
optimal - device is fully functional and is not
running diagnostics that may impact
performance.
verifying - diagnostics are being run on the device.
Performance of the device may be affected.
failed - catastrophic failure has occurred.
warning - user-specified error threshold has been
crossed. Device failure may be imminent.
formatting - device is being formatted.
formatCertifying
- a SCSI format with certify command in
progress.
missing - device is physically missing or does
not respond to commands on the SCSI bus.
notCreated - array has been defined by the user but the
changes are have not been committed to the
hardware.
degraded - redundant array has a failed component
which results in degraded performance and
loss of fault-tolerance.
building - array is in the process of building.
verifyFixing - device is processing an SCSI verify fix
command.
abortActivity - this value allows the user to abort any
background tasks on the controller, such
as Build, Rebuild and Verify.ro DeviceStatus .1.3.6.1.4.1.1597.1.4.1.1.8 |
dptScsiDevBusWidthThe data width of the SCSI device (not applicable to
logical devices).ro BusWidth .1.3.6.1.4.1.1597.1.4.1.1.9 |
dptScsiDevCapacityThe storage capacity of the device in MB.ro INTEGER (0..'FFFFFFFF'h) .1.3.6.1.4.1.1597.1.4.1.1.10 |
dptScsiDevLogicalBlockSizeLogical block size of the device in bytes.ro INTEGER .1.3.6.1.4.1.1597.1.4.1.1.11 |
dptScsiDevPhysicalBlockSizePhysical block size of the device in bytes. Not
applicable for logical devices and will be the logical
block size.ro INTEGER .1.3.6.1.4.1.1597.1.4.1.1.12 |
dptScsiDevNegTransferRateThe negotiated transfer rate of the device in MB/s. For
logical devices, this value is not applicable and will
return 0.ro INTEGER .1.3.6.1.4.1.1597.1.4.1.1.13 |
dptScsiDevRemovableIndicates whether or not the device is removable.ro YesNoStatus .1.3.6.1.4.1.1597.1.4.1.1.14 |
dptScsiDevEccEnabledIndicates whether the device has ECC enabled or
disabled.rodeprecated YesNoStatus .1.3.6.1.4.1.1597.1.4.1.1.15 |
dptScsiDevScsiVersionIndicates the SCSI specification version of the device.ro ScsiVersion .1.3.6.1.4.1.1597.1.4.1.1.16 |
dptScsiDevSoftResetIndicates whether the device supports soft reset.ro YesNoStatus .1.3.6.1.4.1.1597.1.4.1.1.17 |
dptScsiDevCmdQueuingIndicates whether the device is supports command queuing.ro YesNoStatus .1.3.6.1.4.1.1597.1.4.1.1.18 |
dptScsiDevLinkedCmdsIndicates whether the device support linked commands (not
applicable to logical devices).ro YesNoStatus .1.3.6.1.4.1.1597.1.4.1.1.19 |
dptScsiDevSynchronousIndicates whether the device supports synchronous
data transfers.ro YesNoStatus .1.3.6.1.4.1.1597.1.4.1.1.20 |
dptScsiDevRelAddrIndicates whether the device supports relative addressing
(not applicable to logical devices).ro YesNoStatus .1.3.6.1.4.1.1597.1.4.1.1.21 |
dptScsiDevSMARTIndicates whether the device supports SMART specifications
(not applicable to logical devices).ro YesNoStatus .1.3.6.1.4.1.1597.1.4.1.1.22 |
dptScsiDevSCAMIndicates whether the device supports SCAM.rodeprecated YesNoStatus .1.3.6.1.4.1.1597.1.4.1.1.23 |
dptScsiDevBadBlockNumberIf bad blocks have been detected on the device, this
is the address of the most recent one. Otherwise it
will contain 0 (no error). The first valid block starts
at 1. This object is used in the definition of one or
more traps.ro INTEGER (0..'FFFFFFFF'h) .1.3.6.1.4.1.1597.1.4.1.1.24 |
dptScsiDevBadBlockCountThis represents the total number of the bad blocks
encountered most recently on the device starting at
the block number dptScsiDevBadBlockNumber. This object
is needed in the definition of one or more traps.ro INTEGER (0..'FFFFFFFF'h) .1.3.6.1.4.1.1597.1.4.1.1.25 |
dptScsiDevErrorsAboveThresholdIndicates whether or not the error count of the device
has reached the threshold. This value is no longer
supported.rodeprecated YesNoStatus .1.3.6.1.4.1.1597.1.4.1.1.26 |
dptScsiDevDriveLockingOnIndicates whether or not the drive is locked. This value
is no longer supported.rodeprecated YesNoStatus .1.3.6.1.4.1.1597.1.4.1.1.27 |
dptScsiDevLastReqSenseInfoDevice Request Sense information.
It is used in the definition of one or more traps.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.1597.1.4.1.1.28 |
dptScsiDevReadCachingOnIndicates whether or not read caching is on. This value
is not applicable to SmartRAID V and later controllers.rodeprecated YesNoStatus .1.3.6.1.4.1.1597.1.4.1.1.29 |
dptScsiDevReadCacheMaxRecordMaximum record size for read caching. This value is not
applicable to SmartRAID V and later controllers. For these
controllers, this value will be 0.rodeprecated INTEGER .1.3.6.1.4.1.1597.1.4.1.1.30 |
dptScsiDevWriteCachingOnIndicates whether or not write caching is on. This value
is not applicable to SmartRAID V and later controllers.rodeprecated YesNoStatus .1.3.6.1.4.1.1597.1.4.1.1.31 |
dptScsiDevWriteCacheMaxRecordMaximum record size for write caching. This value is not
applicable to SmartRAID V and later controllers. For these
controllers, this value will be 0.rodeprecated INTEGER .1.3.6.1.4.1.1597.1.4.1.1.32 |
dptScsiDevWriteModeThe write modes are Write-back and Write-through, with
write-back being the default.
In write-back mode the controller will cache the data
and return completion to the host before the data is
written to disk. This is the highest performance mode.
In write-through mode the controller will always write
the data to disk before posting complete to the host.
The data may or may not be placed into the controller's
cache.ro DeviceWriteMode .1.3.6.1.4.1.1597.1.4.1.1.33 |
dptScsiDevSmartStatusOkIndicates whether the device has reported a SMART
error not (not applicable to logical devices).ro YesNoStatus .1.3.6.1.4.1.1597.1.4.1.1.34 |
dptScsiDevTypeType of device reported.ro DeviceType .1.3.6.1.4.1.1597.1.4.1.1.35 |
dptScsiArr OBJECT IDENTIFIER .1.3.6.1.4.1.1597.1.5 |
dptScsiArrTableA list of RAID array groups. SEQUENCE OF DptScsiArrEntry .1.3.6.1.4.1.1597.1.5.1 |
dptScsiArrEntryThese parameters describe/control a RAID array group. DptScsiArrEntry .1.3.6.1.4.1.1597.1.5.1.1 |
dptScsiArrTypeThe RAID type for the Logical Drive.
RAID Disk-fault No.of
Level Tolerant Drives
RAID-0 No 2 or more
RAID-1 Yes Even number
RAID-5 Yes 3 or more
Hot Spare - one
Redirected - onero RaidType .1.3.6.1.4.1.1597.1.5.1.1.1 |
dptScsiArrOwnersoftware entity that created this logical device.ro SoftwareType .1.3.6.1.4.1.1597.1.5.1.1.2 |
dptScsiArrNameName of the RAID array group.ro DisplayString .1.3.6.1.4.1.1597.1.5.1.1.3 |
dptScsiArrBackgroundProgressPercentage of completion of an outstanding background
operation, e.g., array Build, Rebuild or Verify.
If there is no current background process, the value is 100
by default.ro INTEGER .1.3.6.1.4.1.1597.1.5.1.1.4 |
dptScsiArrEntryStatus- 'active': indicates that the table row is available for
use by the managed device;
- 'notInService': indicates that the table row
exists in the agent, but is unavailable for use by the
managed device (see NOTE below);
- 'notReady': indicates that the table row exists
in the agent, but is missing information necessary in
order to be available for use by the managed device;
- 'createAndGo': supplied by a management station
wishing to create a new instance of a table row and
to have it available for use by the managed device;
(cannot be returned in a get response)
- 'createAndWait': supplied by a management station
wishing to create a new instance of a table row but
not to have it available for use by the managed device;
and,
(cannot be returned in a get response)
- 'destroy': supplied by a management station wishing
to delete all of the objects associated with an
existing table row.
(cannot be returned in a get response)
To create new row, a manager sets this object to
createAndWait. Agent creates a new row and sets row
status to notInService. After the manager creates
all the corresponding rows in dptScsiArrMemberTable
and has set all the relevant columnar objects, it
finally sets dptScsiArrEntryStatus to active which
saves all the information to the hardware and performs
an array build.
If the manager sets dptScsiArrEntryStatus to active or
notInService and the required number of drives are
not members of this array group (for example, a RAID-5
needs at least 3 drives), then 'inconsistentValue' is
returned.
To delete an array group, the manager sets this object to
destroy. When a row with a particular row index is
destroyed, all corresponding rows in dptScsiArrMemberTable
are destroyed as well.
++ ++
| doesn't exist | > | active |
++ ++
Array group is Array group is Array group is
not created created in the saved to hardware
agent and a build is
performedro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1597.1.5.1.1.5 |
dptScsiArrMemberTableA list of mappings between an array device and its
components. SEQUENCE OF DptScsiArrMemberEntry .1.3.6.1.4.1.1597.1.5.2 |
dptScsiArrMemberEntryThese parameters describe/control the mappings
between an array and its components. In the index
clause, the first set of indices from dptScsiHbaNumber
to dptScsiDevLevel describes the array (parent)
and the second set represents the member (child). DptScsiArrMemberEntry .1.3.6.1.4.1.1597.1.5.2.1 |
dptScsiArrMemberStripeSizeThe stripe size used by the array (in KB). A stripe is
a contiguous region for data storage on a disk. Data is
distributed evenly across component drives in an array
by concatenating interleaved stripes from each drive.
If stripe size is not applicable to a particular type
of RAID (e.g., hot spare), the value is 0.ro INTEGER .1.3.6.1.4.1.1597.1.5.2.1.1 |
dptScsiArrMemberEntryStatusTo create a new row, manager sets this object to
createAndWait. After successful creation of a row
in the agent, it is set to notInService until the
parent array is made active and at that time it
is set to active as well.
Setting it to createAndGo has the same effect as
that of createAndWait.
++ ++
| doesn't exist | > | active |
++ ++
A new row is Array group is
created in the saved to hardware
agent and a build is
performedro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.1597.1.5.2.1.2 |
dptScsiStats OBJECT IDENTIFIER .1.3.6.1.4.1.1597.1.6 |
dptScsiStatsHbaTableA list of controller statistics. SEQUENCE OF DptScsiStatsHbaEntry .1.3.6.1.4.1.1597.1.6.1 |
dptScsiStatsHbaEntryThese parameters describe the statistics of an controller. DptScsiStatsHbaEntry .1.3.6.1.4.1.1597.1.6.1.1 |
dptScsiStatsHbaCacheTotalPagesIndicates the maximum number of data pages that
can be cached on the controller. A page is the smallest
region of cache that can be allocated to store data.
Each page holds one 512-byte disk sector. The value
of this object depends on the memory configuration
of the controller.ro Gauge .1.3.6.1.4.1.1597.1.6.1.1.1 |
dptScsiStatsHbaCacheUsedPagesIndicates the number of data pages residing in the
cache memory. This has the same value as
dptHbaCacheTotalPages when the cache is full.ro Gauge .1.3.6.1.4.1.1597.1.6.1.1.2 |
dptScsiStatsHbaCacheDirtyPagesIndicates the number of cache pages that contain dirty
data. Dirty data is the data which has been written to
the adapter by the computer but has not yet been copied
to the disk. This object has a value of 0 after the
cache is flushed or allowed to write-back during a
period of no disk activity.ro Gauge .1.3.6.1.4.1.1597.1.6.1.1.3 |
dptScsiStatsHbaCacheReadAheadPagesIndicates the number of cache pages that contain
read-ahead data. Read-ahead data is read from the
drives in anticipation of a future access.ro Gauge .1.3.6.1.4.1.1597.1.6.1.1.4 |
dptScsiStatsHbaCacheLockedPagesIndicates the number of data pages residing in the cache
memory that are presently locked. These data pages do
not get paged out until the locks are released.ro Gauge .1.3.6.1.4.1.1597.1.6.1.1.5 |
dptScsiStatsHbaCacheEccFaultPagesThe number of cache pages that have had Error
Correcting Code (ECC) fault and had been reassigned
since power up.
ECC is a method of generating redundant information
that can be used to detect and correct errors in
stored or transmitted data.ro Gauge .1.3.6.1.4.1.1597.1.6.1.1.6 |
dptScsiStatsHbaCommandsThe number of commands received by the controller since
power up.ro Counter .1.3.6.1.4.1.1597.1.6.1.1.7 |
dptScsiStatsHbaMisAlignedTransfersThe number of misaligned data transfers handled by
the controller since power up. In a misaligned data transfer,
data is accessed on odd byte boundary. These transfers
normally take longer to complete than aligned transfers.ro Counter .1.3.6.1.4.1.1597.1.6.1.1.8 |
dptScsiStatsHbaScsiResetsThe number of SCSI reset commands received by the adapter
since power up.ro Counter .1.3.6.1.4.1.1597.1.6.1.1.9 |
dptScsiStatsDevTableA list of Device statistics. SEQUENCE OF DptScsiStatsDevEntry .1.3.6.1.4.1.1597.1.6.2 |
dptScsiStatsDevEntryThese parameters describe the statistics of a device.
The index of this entry is the logical device address of
the device. The logical device address consists of four
fields: controller number, bus number, device ID, logical unit
number and level. DptScsiStatsDevEntry .1.3.6.1.4.1.1597.1.6.2.1 |
dptScsiStatsDevReadTotalSectorsThe number of sectors read from the device since power up.ro Counter .1.3.6.1.4.1.1597.1.6.2.1.1 |
dptScsiStatsDevReadCacheHitsThe number of data accesses since power up in which the
requested data was found in the cache.ro Counter .1.3.6.1.4.1.1597.1.6.2.1.2 |
dptScsiStatsDevReadAheadHitsThe number of data accesses since power up in which the
requested data was found in the read ahead buffer.ro Counter .1.3.6.1.4.1.1597.1.6.2.1.3 |
dptScsiStatsDevWriteTotalSectorsThe number of sectors written to the device since power up.ro Counter .1.3.6.1.4.1.1597.1.6.2.1.4 |
dptScsiStatsDevWriteCacheHitsThe number of data writes, since power up, targeted to
the device in which the data was written to the cache
and not to the disk.ro Counter .1.3.6.1.4.1.1597.1.6.2.1.5 |
dptScsiStatsDevWriteBacksThe number of data writes to the device since power up
in which the data was written from the cache to the
disk at a time when the device would otherwise be idle.ro Counter .1.3.6.1.4.1.1597.1.6.2.1.6 |
dptScsiStatsDevStripesCrossedsThe number of array group accesses that cross stripe
boundaries since power up. Only applicable in case
of array devices; in other cases, it contains zero.ro Counter .1.3.6.1.4.1.1597.1.6.2.1.7 |
dptScsiStatsDevRWCmdsTableA statistical breakdown of read and write commands. SEQUENCE OF DptScsiStatsDevRWCmdsEntry .1.3.6.1.4.1.1597.1.6.3 |
dptScsiStatsDevRWCmdsEntryThese parameters describe the statistics of a device.
The index is the logical device address of the device.
The logical device address consists of: contoller number, bus
number, device ID and logical unit number and device level. DptScsiStatsDevRWCmdsEntry .1.3.6.1.4.1.1597.1.6.3.1 |
dptScsiStatsDevRWCmdsTypeIndicates whether this row represents statistics related to
the commands sent by the O/S of the host computer or the
SCSI commands sent by the controller to the device to do a
physical read or write.ro CommandType .1.3.6.1.4.1.1597.1.6.3.1.1 |
dptScsiStatsDevRead1KsThe number of ScsiDev Group read operations of length <= 1K.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.2 |
dptScsiStatsDevRead2KsThe number of ScsiDev Group read operations of length > 1K & <= 2K.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.3 |
dptScsiStatsDevRead4KsThe number of ScsiDev Group read operations of length > 2K & <= 4K.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.4 |
dptScsiStatsDevRead8KsThe number of ScsiDev Group read operations of length > 4K & <= 8K.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.5 |
dptScsiStatsDevRead16KsThe number of ScsiDev Group read operations of length > 8K <= 16K.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.6 |
dptScsiStatsDevRead32KsThe number of ScsiDev Group read operations of
length > 16K & <= 32K.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.7 |
dptScsiStatsDevRead64KsThe number of ScsiDev Group read operations of
length > 32K & <= 64k.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.8 |
dptScsiStatsDevRead128KsThe number of ScsiDev Group read operations of
length > 64K & <= 128K.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.9 |
dptScsiStatsDevRead256KsThe number of ScsiDev Group read operations of length
> 128K & <= 256K.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.10 |
dptScsiStatsDevRead512KsThe number of ScsiDev Group read operations of length
> 256K & <= 512K.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.11 |
dptScsiStatsDevRead1MBsThe number of ScsiDev Group read operations of length
> 512K & <= 1M.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.12 |
dptScsiStatsDevReadGreater1MBsThe number of ScsiDev Group read operations of length > 1M.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.13 |
dptScsiStatsDevWrite1KsThe number of ScsiDev Group write operations of length <= 1K.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.14 |
dptScsiStatsDevWrite2KsThe number of ScsiDev Group write operations of length
> 1K & <= 2K.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.15 |
dptScsiStatsDevWrite4KsThe number of ScsiDev Group write operations of length
> 2K & <= 4K.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.16 |
dptScsiStatsDevWrite8KsThe number of ScsiDev Group write operations of length
> 4k & <= 8K.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.17 |
dptScsiStatsDevWrite16KsThe number of ScsiDev Group write operations of
length > 8K & <= 16K.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.18 |
dptScsiStatsDevWrite32KsThe number of ScsiDev Group write operations of
length > 16K & <= 32K.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.19 |
dptScsiStatsDevWrite64KsThe number of ScsiDev Group write operations of
length > 32K & <= 64K.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.20 |
dptScsiStatsDevWrite128KsThe number of ScsiDev Group write operations of
length > 64K & <= 128K.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.21 |
dptScsiStatsDevWrite256KsThe number of ScsiDev Group write operations of
length > 128K & <= 256K.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.22 |
dptScsiStatsDevWrite512KsThe number of ScsiDev Group write operations of
length > 256K & <= 512K.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.23 |
dptScsiStatsDevWrite1MBsThe number of ScsiDev Group write operations of
length > 512K & <= 1M.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.24 |
dptScsiStatsDevWriteGreater1MBsThe number of ScsiDev Group write operations of length > 1M.ro Counter .1.3.6.1.4.1.1597.1.6.3.1.25 |
dptScsiEvent OBJECT IDENTIFIER .1.3.6.1.4.1.1597.1.7 |
dptScsiEventInfoRepresents information in a human readable form
(English string) for generic DPT SCSI system traps.ro DisplayString .1.3.6.1.4.1.1597.1.7.1 |
dptScsiEventAuxVoltageAuxiliary voltage status reported by the controller. LowHighStatus .1.3.6.1.4.1.1597.1.7.2 |
dptScsiDummy OBJECT IDENTIFIER .1.3.6.1.4.1.1597.1.8 |
dptScsiHbaNumberMemberAn index that uniquely identifies a row in the
dptHbaTable table that pertain to a particular HBA.
The value of this object is the logical device identifier
for a DPT adapter. In EISA systems, EISA bus slots are
scanned, starting from the lowest slot, looking for DPT
adapters.
In ISA system, DPT adapters are scanned in order of I/O
address. As DPT adapters are found, they are assigned
numbers incrementally, starting with 0. INTEGER .1.3.6.1.4.1.1597.1.8.1 |
dptScsiBusNumberMemberAn index that, along with dptScsHbaNumber uniquely,
identifies an entry in the dptScsiBusTable for a
particular SCSI Bus. INTEGER .1.3.6.1.4.1.1597.1.8.2 |
dptScsiDevIdMemberThe SCSI Id of the device. INTEGER .1.3.6.1.4.1.1597.1.8.3 |
dptScsiDevLunMemberThe SCSI logical unit number of the device. INTEGER .1.3.6.1.4.1.1597.1.8.4 |
dptScsiDevLevelMemberIndicates whether the device is a physical device
(level 0) or a logical device (level 1, level 2, etc).
It also gives its level in the containment hierarchy of
devices.
A device is a logical device if it contains other
SCSI devices, otherwise it is a physical device.
A level 1 array contains only physical devices as its
members; a level 2 device has at least one
level 1 array as a member; and so on.
In the case of HBA with no RAID capabilities, the only
applicable device level is 0. INTEGER .1.3.6.1.4.1.1597.1.8.5 |