DATASMART-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for DATASMART-MIB.
412
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
412 total| Object Name |
|---|
datasmart OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2 |
RFC1155-SMI Unknown .1.3.6.1.4.1.181.2.2 |
dsAcOnPowerTransitionA/B On Power Transition on DataSMART 558 and MPATH 538 TRAP-TYPE .1.3.6.1.4.1.181.2.2.0.5005 |
dsAcOffPowerTransitionA/B Off Power Transition on DataSMART 558 and MPATH 538 TRAP-TYPE .1.3.6.1.4.1.181.2.2.0.5006 |
dsFmcSetNiRcvUpperBwThreshThe total traffic through the unit has exceeded
the configured threshold for NI Receive. TRAP-TYPE .1.3.6.1.4.1.181.2.2.0.9001 |
dsFmcClrNiRcvUpperBwThreshThe total traffic through the unit has crossed back
under 20 percent below the configured threshold after
exceeding the threshold for NI Receive. TRAP-TYPE .1.3.6.1.4.1.181.2.2.0.9002 |
dsFmcSetNiXmtUpperBwThreshThe total traffic through the unit has exceeded
the configured threshold for NI Transmit. TRAP-TYPE .1.3.6.1.4.1.181.2.2.0.9003 |
dsFmcClrNiXmtUpperBwThreshThe total traffic through the unit has crossed back
under 20 percent below the configured threshold after
exceeding the threshold NI Transmit. TRAP-TYPE .1.3.6.1.4.1.181.2.2.0.9004 |
dsFmcFpingLinkDownA VC has transitioned to a link down since FPINGs are not
being returned TRAP-TYPE .1.3.6.1.4.1.181.2.2.0.9005 |
dsFmcFpingLinkUpA VC has transitioned to a link up since an FPING was just
returned TRAP-TYPE .1.3.6.1.4.1.181.2.2.0.9006 |
dsSs OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.1 |
dsSsAlarmSourceIf the alarm is occuring on a port, this object
states which port.ro Enumeration .1.3.6.1.4.1.181.2.2.1.1 |
dsSsAlarmStateThe alarm state the system is currently in.ro Enumeration .1.3.6.1.4.1.181.2.2.1.2 |
dsSsLoopbackThe loopback the system is currently performing.ro Enumeration .1.3.6.1.4.1.181.2.2.1.3 |
dsSsPowerStatusThe status of the A and B power inputs on the
universal shelf.
The possible values are:
VALUE DESCRIPTION
ssBothOff(1) A off, B off
ssAOnBOff(2) A on, B off
ssAOffBOn(3) A off, B on
ssBothOn(4) A on, B on
This is only available on models 558 and 538ro Enumeration .1.3.6.1.4.1.181.2.2.1.4 |
dsRp OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.2 |
dsRpUsr OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.2.1 |
dsRpUsrTmCntTableThe User Time Counts Table. This table contains
information about the number of seconds in the
current 15-minute interval, the number of complete
15-minute intervals in the Interval tabl, and
the number of days in the Day table. SEQUENCE OF DsRpUsrTmCntEntry .1.3.6.1.4.1.181.2.2.2.1.1 |
dsRpUsrTmCntEntryAn entry in the User Time Counts Table. DsRpUsrTmCntEntry .1.3.6.1.4.1.181.2.2.2.1.1.1 |
dsRpUsrTmCntIndexThe index to the User Time Counts Table. The
valid indices are:
VALUE DESCRIPTION
1 Network Interface
2 Terminal Interface
3 Far End Network Interfacero INTEGER .1.3.6.1.4.1.181.2.2.2.1.1.1.1 |
dsRpUsrTmCntSecsThe number of seconds in the current 15-minute
interval.ro INTEGER .1.3.6.1.4.1.181.2.2.2.1.1.1.2 |
dsRpUsrTmCnt15MinsThe number of completed 15-minute intervals
in the Interval Table.ro INTEGER .1.3.6.1.4.1.181.2.2.2.1.1.1.3 |
dsRpUsrTmCntDaysThe number of completed days in the Day Table.ro INTEGER .1.3.6.1.4.1.181.2.2.2.1.1.1.4 |
dsRpUsrCurTableThe User Current Table. This table contains
performance information from the current 15-minute
interval for the Network, Terminal, and Far End
Network Interfaces. SEQUENCE OF DsRpUsrCurEntry .1.3.6.1.4.1.181.2.2.2.1.2 |
dsRpUsrCurEntryAn entry in the User Current Table. DsRpUsrCurEntry .1.3.6.1.4.1.181.2.2.2.1.2.1 |
dsRpUsrCurIndexThe index for the User Current Table. The valid
values for this index are:
VALUE DESCRIPTION
1 Network Interface
2 Terminal Interface
3 Far End Network Interfacero INTEGER .1.3.6.1.4.1.181.2.2.2.1.2.1.1 |
dsRpUsrCurEEThe number of Event Errors encountered by a DS1/E1
interface in the current 15-minute interval.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.2.1.2 |
dsRpUsrCurESThe number of Errored Seconds encountered by a DS1/E1
interface in the current 15-minute interval.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.2.1.3 |
dsRpUsrCurBESThe number of Bursty Errored Seconds encountered
by a DS1/E1 interface in the current 15-minute interval.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.2.1.4 |
dsRpUsrCurSESThe number of Severely Srrored Seconds encountered
by a DS1/E1 intervace in the current 15-minute interval.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.2.1.5 |
dsRpUsrCurUASThe number of Unavailable Seconds encountered by
a DS1/E1 interface in the current 15-minute interval.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.2.1.6 |
dsRpUsrCurCSSThe number of Controlled Slip Seconds encountered
by a DS1/E1 interface in the current 15-minute interval.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.2.1.7 |
dsRpUsrCurDMThe number of Degraded Minutes encountered by a
DS1/E1 interface in the current 15-minute interval.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.2.1.8 |
dsRpUsrCurStatusThe error conditions encountered by a DS1/E1
interface in the current 15-minute interval.
The error conditions are signified by a single
character. The possible values are:
VALUE DESCRIPTION
C A CRC error has been detected on the
received T1/E1 signal
B A bipolar (line) violation has occurred
on the received T1/E1 signal
L A LOS condition (but not necessarily an
alarm) has occurred on the received
T1/E1 signal
O An OOF condition (but not necessarily an
alarm) has occurred on the received
T1/E1
E An EER condition (but not necessarily an
alarm) has occurred on the received
T1/E1 signal
A An AIS condition (but not necessarily an
alarm) has occurred on the received
T1/E1 signal
Y A Yellow alarm has occurred on the received
T1/E1 signal
@ There is an active alarm
T There is a loop back, code generation,
or BERT active
N The unit was without powerro DisplayString .1.3.6.1.4.1.181.2.2.2.1.2.1.9 |
dsRpUsrIntvlTableThe User Interval Table. This table contains
performance information for the past 24 hours,
broken down by 15-minute intervals for the Network,
Terminal, and Far End Network Interfaces. SEQUENCE OF DsRpUsrIntvlEntry .1.3.6.1.4.1.181.2.2.2.1.3 |
dsRpUsrIntvlEntryAn entry in the User Interval Table. DsRpUsrIntvlEntry .1.3.6.1.4.1.181.2.2.2.1.3.1 |
dsRpUsrIntvlIndexThe index for the User Interval Table. The valid
values for this index are:
VALUE DESCRIPTION
1 Network Interface
2 Terminal Interface
3 Far End Network Interfacero INTEGER .1.3.6.1.4.1.181.2.2.2.1.3.1.1 |
dsRpUsrIntvlNumThis is the interval number of the User Interval Table.
It will be the number of completed 15-minute
intervals since the unit has been powered up. After
24 hours, this value remains constant at 96 intervals.ro INTEGER .1.3.6.1.4.1.181.2.2.2.1.3.1.2 |
dsRpUsrIntvlEEThe number of Event Errors encountered by a DS1/E1
interface in one of the previous 96 15-minute
intervals.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.3.1.3 |
dsRpUsrIntvlESThe number of Errored Seconds encountered by a DS1/E1
interface in one of the previous 96 15-minute
intervals.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.3.1.4 |
dsRpUsrIntvlBESThe number of Bursty Errored Seconds encountered
by a DS1/E1 interface in one of the pervious 96
15-minute intervals.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.3.1.5 |
dsRpUsrIntvlSESThe number of Severely Errored Seconds encountered
by a DS1/E1 interface in one of the previous 96
15-minute intervals.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.3.1.6 |
dsRpUsrIntvlUASThe number of Unavailable Seconds encountered by
a DS1/E1 interface in one of the previous 96
15-minute intervals.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.3.1.7 |
dsRpUsrIntvlCSSThe number of Controlled Slip Seconds encountered
by a DS1/E1 interface in one of the previous 96
15-minute intervals.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.3.1.8 |
dsRpUsrIntvlDMThe number of Degraded Minutes encountered by
a DS1/E1 interface in one of the previous 96
15-minute intervals.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.3.1.9 |
dsRpUsrIntvlStatusThe error conditions encountered by a DS1/E1
interface in one of the pervious 96 15-minute
intervals. The error conditions are signified by
a single character. The possible values are:
VALUE DESCRIPTION
C A CRC error has been detected on the
received T1/E1 signal
B A bipolar (line) violation has occurred
on the received T1/E1 signal
L A LOS condition (but not necessarily an
alarm) has occurred on the received
T1/E1 signal
O An OOF condition (but not necessarily an
alarm) has occurred on the received
T1/E1
E An EER condition (but not necessarily an
alarm) has occurred on the received
T1/E1 signal
A An AIS condition (but not necessarily an
alarm) has occurred on the received
T1/E1 signal
Y A Yellow alarm has occurred on the received
T1/E1 signal
S A controlled slip has occurred on the
received T1/E1 signal
@ There is an active alarm
T There is a loop back, code generation,
or BERT active
N The unit was without powerro DisplayString .1.3.6.1.4.1.181.2.2.2.1.3.1.10 |
dsRpUsrTotalTableThe User Total Table. This table contains
performance information for the past 24-hours,
for the Network, Terminal, and Far End Network
Interfaces.
This is a rolling count. When the current
15-minute interval is up, the last entry in the
interval table will be removed and the completed
15-minute interval added. At this point the Total
Table will be re-calculated. SEQUENCE OF DsRpUsrTotalEntry .1.3.6.1.4.1.181.2.2.2.1.4 |
dsRpUsrTotalEntryAn entry in the User Total Table. DsRpUsrTotalEntry .1.3.6.1.4.1.181.2.2.2.1.4.1 |
dsRpUsrTotalIndexThe index for the User Total Table. The valid
indices are:
VALUE DESCRIPTION
1 Network Interface
2 Terminal Interface
3 Far End Network Interfacero INTEGER .1.3.6.1.4.1.181.2.2.2.1.4.1.1 |
dsRpUsrTotalEEThe number of Event Errors encountered by a DS1/E1
interface in the past 24-hours.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.4.1.2 |
dsRpUsrTotalESThe number of Errored Seconds encountered by a DS1/E1
interface in the past 24-hours.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.4.1.3 |
dsRpUsrTotalBESThe number of Bursty Errored Seconds encountered
by a DS1/E1 interface in the past 24-hours.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.4.1.4 |
dsRpUsrTotalSESThe number of Severely Errored Seconds encountered
by a DS1/E1 interface in the past 24-hours.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.4.1.5 |
dsRpUsrTotalUASThe number of Unavailable Seconds encountered by
a DS1/E1 interface in the past 24-hours.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.4.1.6 |
dsRpUsrTotalCSSThe number of Controlled Slip Seconds encountered
by a DS1/E1 interface in the past 24-hours.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.4.1.7 |
dsRpUsrTotalDMThe number of Degraded Minutes encountered by
a DS1/E1 interface in the past 24-hours.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.4.1.8 |
dsRpUsrTotalStatusThe error conditions encountered by a DS1/E1
interface in the past 24-hours. The error conditions
are signified by a single character. The possible
values are:
VALUE DESCRIPTION
C A CRC error has been detected on the
received T1/E1 signal
B A bipolar (line) violation has occurred
on the received T1/E1 signal
L A LOS condition (but not necessarily an
alarm) has occurred on the received
T1/E1 signal
O An OOF condition (but not necessarily an
alarm) has occurred on the received
T1/E1
E An EER condition (but not necessarily an
alarm) has occurred on the received
T1/E1 signal
A An AIS condition (but not necessarily an
alarm) has occurred on the received
T1/E1 signal
Y A Yellow alarm has occurred on the received
T1/E1 signal
S A controlled slip has occurred on the
received T1/E1 signal
@ There is an active alarm
T There is a loop back, code generation,
or BERT active
N The unit was without powerro DisplayString .1.3.6.1.4.1.181.2.2.2.1.4.1.9 |
dsRpUsrDayTableAfter the unit has been powered up for 24 hours,
the values from the User Total Table are moved into
the first slot in the User Day Table. There are seven
entries in the User Day Table, so an entire week's
history is maintained. The previous day is always
in slot 1. SEQUENCE OF DsRpUsrDayEntry .1.3.6.1.4.1.181.2.2.2.1.5 |
dsRpUsrDayEntryThis is an entry in the User Day Table. DsRpUsrDayEntry .1.3.6.1.4.1.181.2.2.2.1.5.1 |
dsRpUsrDayIndexThe User Day Table interface index.
The valid indices are:
VALUE DESCRIPTION
1 Network Interface
2 Terminal Interface
3 Far End Network Interfacero INTEGER .1.3.6.1.4.1.181.2.2.2.1.5.1.1 |
dsRpUsrDayNumThe User Day Table day index. The valid
values are 1 day to 7 days.ro INTEGER .1.3.6.1.4.1.181.2.2.2.1.5.1.2 |
dsRpUsrDayEEThe number of Event Errors encountered by a DS1/E1
interface in one of the previous days.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.5.1.3 |
dsRpUsrDayESThe number of Errored Seconds encountered by a
DS1/E1 interface in one of the previous days.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.5.1.4 |
dsRpUsrDayBESThe number of Bursty Errored Seconds encountered
by a DS1/E1 interface in one of the previous days.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.5.1.5 |
dsRpUsrDaySESThe number of Severely Errored Seconds encountered
by a DS1/E1 interface in one of the previous days.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.5.1.6 |
dsRpUsrDayUASThe number of Unavailable Seconds encountered by
a DS1/E1 interface in one of the previous days.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.5.1.7 |
dsRpUsrDayCSSThe number of Controlled Slip Seconds encountered
by a DS1/E1 interface in one of the previous days.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.5.1.8 |
dsRpUsrDayDMThe number of Degraded Minutes encountered by
a DS1/E1 interface in one of the previous days.ro Gauge .1.3.6.1.4.1.181.2.2.2.1.5.1.9 |
dsRpUsrDayStatusThe error conditions encountered by a DS1/E1
interface in one of the previous days. The error
conditions are signified by a single character.
The possible values are:
VALUE DESCRIPTION
C A CRC error has been detected on the
received T1/E1 signal
B A bipolar (line) violation has occurred
on the received T1/E1 signal
L A LOS condition (but not necessarily an
alarm) has occurred on the received
T1/E1 signal
O An OOF condition (but not necessarily an
alarm) has occurred on the received
T1/E1
E An EER condition (but not necessarily an
alarm) has occurred on the received
T1/E1 signal
A An AIS condition (but not necessarily an
alarm) has occurred on the received
T1/E1 signal
Y A Yellow alarm has occurred on the received
T1/E1 signal
S A controlled slip has occurred on the
received T1/E1 signal
@ There is an active alarm
T There is a loop back, code generation,
or BERT active
N The unit was without powerro DisplayString .1.3.6.1.4.1.181.2.2.2.1.5.1.10 |
dsRpCar OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.2.2 |
dsRpCarCntSecsThe number of seconds that have elapsed in the
current interval.ro INTEGER .1.3.6.1.4.1.181.2.2.2.2.1 |
dsRpCarCnt15MinsThe number of 15-minute intervals that have
elapsed in the current 24-hours.ro INTEGER .1.3.6.1.4.1.181.2.2.2.2.2 |
dsRpCarCur OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.2.2.3 |
dsRpCarCurEEThe number of Event Errors encountered by the
Network Interface in the current 15-minute interval.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.3.1 |
dsRpCarCurESThe number of Errored Seconds encountered by the
Network Interface in the current 15-minute interval.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.3.2 |
dsRpCarCurBESThe number of Bursty Errored Seconds encountered by
the Network Interface in the current 15-minute
interval.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.3.3 |
dsRpCarCurSESThe number of Severely Errored Seconds encountered
by the Network Interface in the current 15-minute
interval.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.3.4 |
dsRpCarCurUASThe number of Unavailable Seconds encountered by
the Network Interface in the current 15-minute
interval.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.3.5 |
dsRpCarCurCSSThe number of Controlled Slip Seconds encountered
by the Network Interface in the current 15-minute
interval.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.3.6 |
dsRpCarCurLOFCThe Loss of Frame Count for the Network Interface
in the current 15-minute interval.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.3.7 |
dsRpCarIntvlTableThis is the Carrier Interval Table. This table
contains performance information about the
Network Interface. SEQUENCE OF DsRpCarIntvlEntry .1.3.6.1.4.1.181.2.2.2.2.4 |
dsRpCarIntvlEntryThis is an entry in the Carrier Interval Table. DsRpCarIntvlEntry .1.3.6.1.4.1.181.2.2.2.2.4.1 |
dsRpCarIntvlNumThe number of the 15-minute interval (1-96) from
the previous 24-hour period. 1 is the most recent.ro INTEGER .1.3.6.1.4.1.181.2.2.2.2.4.1.1 |
dsRpCarIntvlEEThe number of Event Errors encountered by the
Network Interface in one of the previous 96
15-minute intervals.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.4.1.2 |
dsRpCarIntvlESThe number of Errored Seconds encountered by
the Network Interface in one of the previous 96
15-minute intervals.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.4.1.3 |
dsRpCarIntvlBESThe number of Bursty Errored Seconds encountered
by the Network Interface in one of the previous 96
15-minute intervals.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.4.1.4 |
dsRpCarIntvlSESThe number of Severely Errored Seconds encountered
by the Network Interface in one of the previous 96
15-minute intervals.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.4.1.5 |
dsRpCarIntvlUASThe number of Unavailable Seconds encountered
by the Network Interface in one of the previous 96
15-minute intervals.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.4.1.6 |
dsRpCarIntvlCSSThe number of Controlled Slip Seconds encountered
by the Network Interface in one of the previous 96
15-minute intervals.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.4.1.7 |
dsRpCarIntvlLOFCThe Loss of Frame Count fo the Network Interface
for one of the previous 96 15-minute intervals.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.4.1.8 |
dsRpCarTotal OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.2.2.5 |
dsRpCarTotalEEThe number of Errored Events encountered by the
Network Interface in the past 24-hours.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.5.1 |
dsRpCarTotalESThe number of Errored Seconds encountered by the
Network Interface in the past 24-hours.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.5.2 |
dsRpCarTotalBESThe number of Bursty Errored Seconds encountered
by the Network Interface in the past 24-hours.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.5.3 |
dsRpCarTotalSESThe number of Severely Errored Seconds encountered
by the Network Interface in the past 24-hours.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.5.4 |
dsRpCarTotalUASThe number of Unavailable Seconds encountered
by the Network Interface in the past 24-hours.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.5.5 |
dsRpCarTotalCSSThe number of Controlled Slip Seconds encountered
by the Network Interface in the past 24-hours.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.5.6 |
dsRpCarTotalLOFCThe Loss of Frame Count for the Network Interface
for one of the previous 96 15-minute intervals.ro Gauge .1.3.6.1.4.1.181.2.2.2.2.5.7 |
dsRpStat OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.2.3 |
dsRpStTableThe Statistics Table. This table consists of
statistical error counts of various DS1/E1
line conditions. These counts are maintained
between power-cycles. SEQUENCE OF DsRpStEntry .1.3.6.1.4.1.181.2.2.2.3.1 |
dsRpStEntryAn entry in the Statistics Table. DsRpStEntry .1.3.6.1.4.1.181.2.2.2.3.1.1 |
dsRpStIndexThe index into the Statistics Table. The valid
indices are:
VALUE DESCRIPTION
1 Network Interface
2 Terminal Interface
3 Far End Network Interfacero INTEGER .1.3.6.1.4.1.181.2.2.2.3.1.1.1 |
dsRpStEsfErrorsThe total number of Error Free Seconds since
the counters have last been cleared.ro Counter .1.3.6.1.4.1.181.2.2.2.3.1.1.2 |
dsRpStCrcErrorsThe total number of CRC errors since the
counters have last been cleared.ro Counter .1.3.6.1.4.1.181.2.2.2.3.1.1.3 |
dsRpStOofErrorsThe total number of Out Of Frame errors since
the counters have last been cleared.ro Counter .1.3.6.1.4.1.181.2.2.2.3.1.1.4 |
dsRpStFrameBitErrorsThe total number of Frame Bit errors since
the counters have last been cleared.ro Counter .1.3.6.1.4.1.181.2.2.2.3.1.1.5 |
dsRpStBPVsThe total number of Bipolar Violations since
the counters have last been cleared.ro Counter .1.3.6.1.4.1.181.2.2.2.3.1.1.6 |
dsRpStControlledSlipsThe total number of Controlled Slips since the
counters have last been cleared.ro Counter .1.3.6.1.4.1.181.2.2.2.3.1.1.7 |
dsRpStYellowEventsThe total number of Yellow Events since the
counters have last been cleared.ro Counter .1.3.6.1.4.1.181.2.2.2.3.1.1.8 |
dsRpStAISEventsThe total number of Alarm Indication Siganl
events since the counters have last been cleared.ro Counter .1.3.6.1.4.1.181.2.2.2.3.1.1.9 |
dsRpStLOFEventsThe total number of Loss of Frame events since
the counters have last been cleared.ro Counter .1.3.6.1.4.1.181.2.2.2.3.1.1.10 |
dsRpStLOSEventsThe total number of Loss of Signal events since
the counters have last been cleared.ro Counter .1.3.6.1.4.1.181.2.2.2.3.1.1.11 |
dsRpStFarEndBlkErrorsThe total number of Far End Block Errors since
the counters were last cleared.ro Counter .1.3.6.1.4.1.181.2.2.2.3.1.1.12 |
dsRpStRemFrameAlmEvtsThe total number of Remote Frame Alarm events
since the counters were last cleared.ro Counter .1.3.6.1.4.1.181.2.2.2.3.1.1.13 |
dsRpStRemMFrameAlmEvtsThe total number of Remote MultiFrame Alarm
events since the counters were last cleared.ro Counter .1.3.6.1.4.1.181.2.2.2.3.1.1.14 |
dsRpStLOTS16MFrameEvtsThe total number of Loss of TS16MultiFrame events
since the counters have been cleared.ro Counter .1.3.6.1.4.1.181.2.2.2.3.1.1.15 |
dsRpStZeroCountersThis object will clear the Statistics Table counters
when it is set to rpStZeroCounterStart(2). Once the
counters have been cleraed, it will return to its
normal state of rpStZeroCountersIdle(1).rw Enumeration .1.3.6.1.4.1.181.2.2.2.3.1.1.16 |
dsRpPl OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.2.4 |
dsPlBreakThis object determines if the user interface
uses page breaks or 'more' prompts when displaying
information which is longer than the defined page
length (e.g., output from UNLR or SCV). A page length
of 0 will disable both page breaks and 'more' prompts.
VALUE DESCRIPTION
rpPlLineFeed(1) Use linefeeds for page breaks
rpPlMorePrompt(2) Use 'more' prompts for page breaksrw Enumeration .1.3.6.1.4.1.181.2.2.2.4.1 |
dsPlLenThe length of a 'page' of information. When the set
number of lines have been displayed, a 'more' prompt
or linefeed will be inserted (defined by dsPlBreak).
A page length of 0 causes output to scroll continuously
without page breaks or 'more' prompts.rw INTEGER ( 0 .. 70 ) .1.3.6.1.4.1.181.2.2.2.4.2 |
dsRpAhrTableThis is the Alarm History Table. It contains
the text messages of the last 20 alarms. SEQUENCE OF DsRpAhrEntry .1.3.6.1.4.1.181.2.2.2.5 |
dsRpAhrEntryAn entry in the Alarm History Table. DsRpAhrEntry .1.3.6.1.4.1.181.2.2.2.5.1 |
dsRpAhrIndexThe Alarm History Table index. Index 1 is the
most recent alarm.ro INTEGER .1.3.6.1.4.1.181.2.2.2.5.1.1 |
dsRpAhrStrThe alarm message in USER format.ro DisplayString .1.3.6.1.4.1.181.2.2.2.5.1.2 |
dsRpShrTableThis is the Security History Report table. It contains
entries for events which are considered important
from a security standpoint. Examples of such events
are 1) incorrect Telnet password entered and 2) source
IP address not on IP Screen List.
The entries are placed in chronological order, with
most recent event first. SEQUENCE OF DsRpShrEntry .1.3.6.1.4.1.181.2.2.2.6 |
dsRpShrEntryAn entry in the Security History Report table. DsRpShrEntry .1.3.6.1.4.1.181.2.2.2.6.1 |
dsRpShrIndexThe Security History Report table index. Events are in
chronological order. This number ranges between 1 and
the value of dsRpShrNumber. Index 1 is the most
recent event.ro INTEGER .1.3.6.1.4.1.181.2.2.2.6.1.1 |
dsRpShrDateTimeDisplay string showing date & time that the
security related event occurred.ro DisplayString .1.3.6.1.4.1.181.2.2.2.6.1.2 |
dsRpShrEventTypeShows what type of security related event occurred.
VALUE DESCRIPTION
rpShrTelnetPassword (1)
- Incorrect Telnet password entered
rpShrSrcIpAddressScreen (2)
- Source IP address not on IP Screen List
rpShrReadCommString (3)
- Incorrect SNMP Read Community String
rpShrWriteCommString (4)
- Incorrect SNMP Write Community Stringro Enumeration .1.3.6.1.4.1.181.2.2.2.6.1.3 |
dsRpShrCommentsDisplay string showing additional information specific
to the type of event. For example, for events of
type rpShrTelnetPassword, the IP address of the
remote host is given.ro DisplayString .1.3.6.1.4.1.181.2.2.2.6.1.4 |
dsRpBesThe error threshold for Bursty Errored Seconds.rw INTEGER .1.3.6.1.4.1.181.2.2.2.7 |
dsRpSesThe threshold for Severely Errored Seconds.rw INTEGER .1.3.6.1.4.1.181.2.2.2.8 |
dsRpDmThe threshold for Degraded Minutes.rw INTEGER .1.3.6.1.4.1.181.2.2.2.9 |
dsRpFr OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.2.10 |
dsRpFrTmCntTableThe FRIB Time Counts Table. This table contains
information for the number of seconds in the
current 2-hour interval, the number of complete
2-hour intervals in the Interval table, and
the number of days in the Day table. SEQUENCE OF DsRpFrTmCntEntry .1.3.6.1.4.1.181.2.2.2.10.1 |
dsRpFrTmCntEntryAn entry in the FRIB Time Counts Table. DsRpFrTmCntEntry .1.3.6.1.4.1.181.2.2.2.10.1.1 |
dsRpFrTmCntDirThe direction index to the FRIB Time Counts Table. The
valid indices are:
VALUE DESCRIPTION
1 Transmit
2 Receivero INTEGER .1.3.6.1.4.1.181.2.2.2.10.1.1.1 |
dsRpFrTmCntSecsThe number of seconds in the current 2-hour interval.ro INTEGER .1.3.6.1.4.1.181.2.2.2.10.1.1.2 |
dsRpFrTmCnt2HrsThe number of completed 2-hour intervals
in the Interval Table.ro INTEGER .1.3.6.1.4.1.181.2.2.2.10.1.1.3 |
dsRpFrTmCntDaysThe number of completed days in the Day Table.ro INTEGER .1.3.6.1.4.1.181.2.2.2.10.1.1.4 |
dsRpFrPre15MTableThe FRIB Previous 15 Min Table. This table contains
performance information from the previous 15-minute
interval for both the transmit and receive directions
of each VC at the Network Interface. SEQUENCE OF DsRpFrPre15MEntry .1.3.6.1.4.1.181.2.2.2.10.2 |
dsRpFrPre15MEntryAn entry in the FRIB Previous 15 Min Table. DsRpFrPre15MEntry .1.3.6.1.4.1.181.2.2.2.10.2.1 |
dsRpFrPre15MDirThe direction index to the FRIB Previous 15 Min Table.
VALUE DESCRIPTION
1 Transmit
2 Receivero INTEGER .1.3.6.1.4.1.181.2.2.2.10.2.1.1 |
dsRpFrPre15MVcIndexThe VC index to the FRIB Previous 15 Min Table. The
table has 64 entries for indiviual VCs, a value of
1 through 64, and 1 entry for all other VCs, a value
of 65.ro INTEGER .1.3.6.1.4.1.181.2.2.2.10.2.1.2 |
dsRpFrPre15MVcThe VC for this entry in the FRIB Previous 15 Min
Table.ro INTEGER .1.3.6.1.4.1.181.2.2.2.10.2.1.3 |
dsRpFrPre15MFramesThe number of Frame Relay packets transmitted or
received during the previous 15-minute interval.ro Counter .1.3.6.1.4.1.181.2.2.2.10.2.1.4 |
dsRpFrPre15MOctetsThe number of octets transmitted or
received during the previous 15-minute interval.ro Counter .1.3.6.1.4.1.181.2.2.2.10.2.1.5 |
dsRpFrPre15MKbpsThe Kilobit/sec rate for data transmitted or
received during the previous 15-minute interval.ro Gauge .1.3.6.1.4.1.181.2.2.2.10.2.1.6 |
dsRpFrPre15MFpMaxThe maximum FPING roundtrip time (in msec) of all
FPINGs on this VC during the previous 15-minute
interval.ro Counter .1.3.6.1.4.1.181.2.2.2.10.2.1.7 |
dsRpFrPre15MFpAvgThe average FPING roundtrip time (in msec) of all
FPINGs on this VC during the previous 15-minute
interval.ro Gauge .1.3.6.1.4.1.181.2.2.2.10.2.1.8 |
dsRpFrPre15MFpLostThe number of FPINGs responses that were not returned
on this VC during the previous 15-minute interval.ro Counter .1.3.6.1.4.1.181.2.2.2.10.2.1.9 |
dsRpFrPre15MFpSentThe number of FPINGs transmitted on this VC
during the previous 15-minute interval.ro Counter .1.3.6.1.4.1.181.2.2.2.10.2.1.10 |
dsRpFrPre15MStatusThe status summary of this VC during the previous
15-minute interval:
VALUE DESCRIPTION
U VC link is UP
D VC link is DOWN
B At least one frame had the BECN bit set
F At least one frame had the FECN bit set
E At least one frame had the DE bit set
P The total pipe threshold for utilization
was exceeded
V The roundtrip threshold for this VC was exceededro DisplayString .1.3.6.1.4.1.181.2.2.2.10.2.1.11 |
dsRpFrCur15MTableThe FRIB Current 15 Min Table. This table contains
performance information from the current 15-minute
interval for both the transmit and receive directions
of each VC at the Network Interface. SEQUENCE OF DsRpFrCur15MEntry .1.3.6.1.4.1.181.2.2.2.10.3 |
dsRpFrCur15MEntryAn entry in the FRIB Current 15 Min Table. DsRpFrCur15MEntry .1.3.6.1.4.1.181.2.2.2.10.3.1 |
dsRpFrCur15MDirThe direction index to the FRIB Current 15 Min Table.
VALUE DESCRIPTION
1 Transmit
2 Receivero INTEGER .1.3.6.1.4.1.181.2.2.2.10.3.1.1 |
dsRpFrCur15MVcIndexThe VC index to the FRIB Current 15 Min Table. The
table has 64 entries for indiviual VCs and the 65th entry
for all other VCs including errored frames.ro INTEGER .1.3.6.1.4.1.181.2.2.2.10.3.1.2 |
dsRpFrCur15MVcThe VC for this entry in the FRIB Current 15 Min Table.ro INTEGER .1.3.6.1.4.1.181.2.2.2.10.3.1.3 |
dsRpFrCur15MFramesThe number of Frame Relay packets transmitted or
received during the current 15-minute interval.ro Counter .1.3.6.1.4.1.181.2.2.2.10.3.1.4 |
dsRpFrCur15MOctetsThe number of octets transmitted or
received during the current 15-minute interval.ro Counter .1.3.6.1.4.1.181.2.2.2.10.3.1.5 |
dsRpFrCur15MKbpsThe Kilobit/sec rate for data transmitted or
received during the current 15-minute interval.ro Gauge .1.3.6.1.4.1.181.2.2.2.10.3.1.6 |
dsRpFrCur15MFpMaxThe maximum FPING roundtrip time (in msec) of all
FPINGs on this VC during the current 15-minute
interval.ro Counter .1.3.6.1.4.1.181.2.2.2.10.3.1.7 |
dsRpFrCur15MFpAvgThe average FPING roundtrip time (in msec) of all
FPINGs on this VC during the current 15-minute
interval.ro Gauge .1.3.6.1.4.1.181.2.2.2.10.3.1.8 |
dsRpFrCur15MFpLostThe number of FPINGs responses received on this
VC during the current 15-minute interval.ro Counter .1.3.6.1.4.1.181.2.2.2.10.3.1.9 |
dsRpFrCur15MFpSentThe number of FPINGs transmitted on this VC
during the current 15-minute interval.ro Counter .1.3.6.1.4.1.181.2.2.2.10.3.1.10 |
dsRpFrCur15MFpRmtIpThe IP Address of the unit at the remote end of the VC.ro IpAddress .1.3.6.1.4.1.181.2.2.2.10.3.1.11 |
dsRpFrCur15MFpRmtVcThe VC number at the remote end of the VC.ro INTEGER .1.3.6.1.4.1.181.2.2.2.10.3.1.12 |
dsRpFrCur15MStatusThe status summary of this VC during the current
15-minute interval:
VALUE DESCRIPTION
U VC link is UP
D VC link is DOWN
B At least one frame had the BECN bit set
F At least one frame had the FECN bit set
E At least one frame had the DE bit set
P The total pipe threshold for utilization
was exceeded
V The roundtrip threshold for this VC was exceededro DisplayString .1.3.6.1.4.1.181.2.2.2.10.3.1.13 |
dsRpFrCur2HTableThe FRIB Current 2Hr Table. This table contains
performance information from the current 2-hour
interval for both the transmit and receive directions
of each VC at the Network Interface. SEQUENCE OF DsRpFrCur2HEntry .1.3.6.1.4.1.181.2.2.2.10.4 |
dsRpFrCur2HEntryAn entry in the FRIB Current 2Hr Table. DsRpFrCur2HEntry .1.3.6.1.4.1.181.2.2.2.10.4.1 |
dsRpFrCur2HDirThe direction index to the FRIB Current 2Hr Table.
VALUE DESCRIPTION
1 Transmit
2 Receivero INTEGER .1.3.6.1.4.1.181.2.2.2.10.4.1.1 |
dsRpFrCur2HVcIndexThe VC index to the FRIB Current 2Hr Table. The
table has 64 entries for indiviual VCs and 1 entry
for all other VCs.ro INTEGER .1.3.6.1.4.1.181.2.2.2.10.4.1.2 |
dsRpFrCur2HVcThe VC for this entry in the FRIB Current 2Hr Table.ro INTEGER .1.3.6.1.4.1.181.2.2.2.10.4.1.3 |
dsRpFrCur2HFramesThe number of Frame Relay packets transmitted or
received during the current 2-hour interval.ro Counter .1.3.6.1.4.1.181.2.2.2.10.4.1.4 |
dsRpFrCur2HOctetsThe number of octets transmitted or
received during the current 2-hour interval.ro Counter .1.3.6.1.4.1.181.2.2.2.10.4.1.5 |
dsRpFrCur2HKbpsThe Kilobit/sec rate for data transmitted or
received during the current 2-hour interval.ro Gauge .1.3.6.1.4.1.181.2.2.2.10.4.1.6 |
dsRpFrCur2HFpMaxThe maximum FPING roundtrip time (in msec) of all
FPINGs on this VC during the current 2-hour interval.ro Counter .1.3.6.1.4.1.181.2.2.2.10.4.1.7 |
dsRpFrCur2HFpAvgThe average FPING roundtrip time (in msec) of all
FPINGs on this VC during the current 2-hour interval.ro Gauge .1.3.6.1.4.1.181.2.2.2.10.4.1.8 |
dsRpFrCur2HFpLostThe number of FPINGs responses received on this
VC during the current 2-hour interval.ro Counter .1.3.6.1.4.1.181.2.2.2.10.4.1.9 |
dsRpFrCur2HFpSentThe number of FPINGs transmitted on this VC
during the current 2-hour interval.ro Counter .1.3.6.1.4.1.181.2.2.2.10.4.1.10 |
dsRpFrCur2HStatusThe status summary of this VC during the current
2-hour interval:
VALUE DESCRIPTION
U VC link is UP
D VC link is DOWN
B At least one frame had the BECN bit set
F At least one frame had the FECN bit set
E At least one frame had the DE bit set
P The total pipe threshold for utilization
was exceeded
V The roundtrip threshold for this VC was exceededro DisplayString .1.3.6.1.4.1.181.2.2.2.10.4.1.11 |
dsRpFrIntvl2HTableThe User 2H Interval Table. This table contains
performance information for the past 24 hours,
broken down by 2-hour intervals. SEQUENCE OF DsRpFrIntvl2HEntry .1.3.6.1.4.1.181.2.2.2.10.5 |
dsRpFrIntvl2HEntryAn entry in the FRIB 2H Interval Table. DsRpFrIntvl2HEntry .1.3.6.1.4.1.181.2.2.2.10.5.1 |
dsRpFrIntvl2HDirThe direction index to the FRIB 2H Interval Table.
VALUE DESCRIPTION
1 Transmit
2 Receivero INTEGER .1.3.6.1.4.1.181.2.2.2.10.5.1.1 |
dsRpFrIntvl2HVcIndexThe VC index to the FRIB 2H Interval Table. The
table has 64 entries for indiviual VCs and 1 entry
for all other VCs.ro INTEGER .1.3.6.1.4.1.181.2.2.2.10.5.1.2 |
dsRpFrIntvl2HNumThis is the interval number of the FRIB 2H Interval
Table. It will be the number of completed 2-hour
intervals since the unit has been powered up. After
24 hours, this value remains constant at 12 intervals.
1 is the most recent interval.ro INTEGER .1.3.6.1.4.1.181.2.2.2.10.5.1.3 |
dsRpFrIntvl2HVcThe VC for this entry in the FRIB 2H Interval Table.ro INTEGER .1.3.6.1.4.1.181.2.2.2.10.5.1.4 |
dsRpFrIntvl2HFramesThe number of Frame Relay packets transmitted or
received during one of the previous 12 2-hour
intervals.ro Counter .1.3.6.1.4.1.181.2.2.2.10.5.1.5 |
dsRpFrIntvl2HOctetsThe number of octets transmitted or
received during one of the previous 12 2-hour
intervals.ro Counter .1.3.6.1.4.1.181.2.2.2.10.5.1.6 |
dsRpFrIntvl2HKbpsThe Kilobit/sec rate for data transmitted or
received during one of the previous 12 2-hour
intervals.ro Gauge .1.3.6.1.4.1.181.2.2.2.10.5.1.7 |
dsRpFrIntvl2HFpMaxThe maximum FPING roundtrip time (in msec) of all
FPINGs on this VC during one of the previous 12 2-hour
intervals.ro Counter .1.3.6.1.4.1.181.2.2.2.10.5.1.8 |
dsRpFrIntvl2HFpAvgThe average FPING roundtrip time (in msec) of all
FPINGs on this VC during one of the previous 12 2-hour
intervals.ro Gauge .1.3.6.1.4.1.181.2.2.2.10.5.1.9 |
dsRpFrIntvl2HFpLostThe number of FPINGs responses received on this
VC during one of the previous 12 2-hour intervals.ro Counter .1.3.6.1.4.1.181.2.2.2.10.5.1.10 |
dsRpFrIntvl2HFpSentThe number of FPINGs transmitted on this VC
during one of the previous 12 2-hour intervals.ro Counter .1.3.6.1.4.1.181.2.2.2.10.5.1.11 |
dsRpFrIntvl2HStatusThe status summary of this VC during the one of
the previous 12 2-hour intervals:
VALUE DESCRIPTION
U VC link is UP
D VC link is DOWN
B At least one frame had the BECN bit set
F At least one frame had the FECN bit set
E At least one frame had the DE bit set
P The total pipe threshold for utilization
was exceeded
V The roundtrip threshold for this VC was exceededro DisplayString .1.3.6.1.4.1.181.2.2.2.10.5.1.12 |
dsRpFrTotalTableThe FRIB Total Table. This table contains
performance information for the past 24-hours
for Frame Relay data being passed throught the NI
Interface.
This is a rolling count. When the current
2-hour interval is up, the last entry in the
interval table will be removed and the completed
2-hour interval added. At this point the Total
Table will be re-calculated. SEQUENCE OF DsRpFrTotalEntry .1.3.6.1.4.1.181.2.2.2.10.6 |
dsRpFrTotalEntryAn entry in the FRIB Total Table. DsRpFrTotalEntry .1.3.6.1.4.1.181.2.2.2.10.6.1 |
dsRpFrTotalDirThe direction index to the FRIB Total Table.
VALUE DESCRIPTION
1 Transmit
2 Receivero INTEGER .1.3.6.1.4.1.181.2.2.2.10.6.1.1 |
dsRpFrTotalVcIndexThe VC index to the FRIB Total Table. The
table has 64 entries for indiviual VCs and 1 entry
for all other VCs.ro INTEGER .1.3.6.1.4.1.181.2.2.2.10.6.1.2 |
dsRpFrTotalVcThe VC for this entry in the FRIB Total Table.ro INTEGER .1.3.6.1.4.1.181.2.2.2.10.6.1.3 |
dsRpFrTotalFramesThe number of Frame Relay packets transmitted or
received during the past 24 hours.ro Counter .1.3.6.1.4.1.181.2.2.2.10.6.1.4 |
dsRpFrTotalOctetsThe number of octets transmitted or
received during the past 24 hours.ro Counter .1.3.6.1.4.1.181.2.2.2.10.6.1.5 |
dsRpFrTotalKbpsThe Kilobit/sec rate for data transmitted or
received during the past 24 hours.ro Gauge .1.3.6.1.4.1.181.2.2.2.10.6.1.6 |
dsRpFrTotalFpMaxThe maximum FPING roundtrip time (in msec) of all
FPINGs on this VC during the past 24 hours.ro Counter .1.3.6.1.4.1.181.2.2.2.10.6.1.7 |
dsRpFrTotalFpAvgThe average FPING roundtrip time (in msec) of all
FPINGs on this VC during the past 24 hours.ro Gauge .1.3.6.1.4.1.181.2.2.2.10.6.1.8 |
dsRpFrTotalFpLostThe number of FPINGs responses received on this
VC during the past 24 hours.ro Counter .1.3.6.1.4.1.181.2.2.2.10.6.1.9 |
dsRpFrTotalFpSentThe number of FPINGs transmitted on this VC
during the past 24 hours.ro Counter .1.3.6.1.4.1.181.2.2.2.10.6.1.10 |
dsRpFrTotalStatusThe status summary of this VC during the past 24 hours:
VALUE DESCRIPTION
U VC link is UP
D VC link is DOWN
B At least one frame had the BECN bit set
F At least one frame had the FECN bit set
E At least one frame had the DE bit set
P The total pipe threshold for utilization
was exceeded
V The roundtrip threshold for this VC was exceededro DisplayString .1.3.6.1.4.1.181.2.2.2.10.6.1.11 |
dsRpFrDayTableAfter the unit has been powered up for 24 hours,
the values from the FRIB Total Table are moved into
the first slot in the FRIB Day Table. There are seven
entries in the FRIB Day Table, so an entire week's
history is maintained. The previous day is always
in slot 1. SEQUENCE OF DsRpFrDayEntry .1.3.6.1.4.1.181.2.2.2.10.7 |
dsRpFrDayEntryThis is an entry in the FRIB Day Table. DsRpFrDayEntry .1.3.6.1.4.1.181.2.2.2.10.7.1 |
dsRpFrDayDirThe direction index to the FRIB Day Table.
VALUE DESCRIPTION
1 Transmit
2 Receivero INTEGER .1.3.6.1.4.1.181.2.2.2.10.7.1.1 |
dsRpFrDayVcIndexThe VC index to the FRIB Day Table. The
table has 64 entries for indiviual VCs and 1 entry
for all other VCs.ro INTEGER .1.3.6.1.4.1.181.2.2.2.10.7.1.2 |
dsRpFrDayNumThe FRIB Day Table index. The valid values are
1 to 7 days. 1 is the most recent interval.ro INTEGER .1.3.6.1.4.1.181.2.2.2.10.7.1.3 |
dsRpFrDayVcThe VC for this entry in the FRIB Day Table.ro INTEGER .1.3.6.1.4.1.181.2.2.2.10.7.1.4 |
dsRpFrDayFramesThe number of Frame Relay packets transmitted or
received during one of the previous days.ro Counter .1.3.6.1.4.1.181.2.2.2.10.7.1.5 |
dsRpFrDayOctetsThe number of octets transmitted or
received during one of the previous days.ro Counter .1.3.6.1.4.1.181.2.2.2.10.7.1.6 |
dsRpFrDayKbpsThe Kilobit/sec rate for data transmitted or
received during one of the previous days.ro Gauge .1.3.6.1.4.1.181.2.2.2.10.7.1.7 |
dsRpFrDayFpMaxThe maximum FPING roundtrip time (in msec) of all
FPINGs on this VC during one of the previous days.ro Counter .1.3.6.1.4.1.181.2.2.2.10.7.1.8 |
dsRpFrDayFpAvgThe average FPING roundtrip time (in msec) of all
FPINGs on this VC during one of the previous days.ro Gauge .1.3.6.1.4.1.181.2.2.2.10.7.1.9 |
dsRpFrDayFpLostThe number of FPINGs responses received on this
VC during one of the previous days.ro Counter .1.3.6.1.4.1.181.2.2.2.10.7.1.10 |
dsRpFrDayFpSentThe number of FPINGs transmitted on this VC
during one of the previous days.ro Counter .1.3.6.1.4.1.181.2.2.2.10.7.1.11 |
dsRpFrDayStatusThe status summary of this VC during the one of
the previous days:
VALUE DESCRIPTION
U VC link is UP
D VC link is DOWN
B At least one frame had the BECN bit set
F At least one frame had the FECN bit set
E At least one frame had the DE bit set
P The total pipe threshold for utilization
was exceeded
V The roundtrip threshold for this VC was exceededro DisplayString .1.3.6.1.4.1.181.2.2.2.10.7.1.12 |
dsRpFrUrTableThis is a utilization report on non-flag octets that
have been transmitted out the network interface for each
VC. SEQUENCE OF DsRpFrUrEntry .1.3.6.1.4.1.181.2.2.2.10.8 |
dsRpFrUrEntryThis is an entry in the FRIB Ur Table. DsRpFrUrEntry .1.3.6.1.4.1.181.2.2.2.10.8.1 |
dsRpFrUrDirThe direction index to the FRIB Ur Table. Receive is
currently not supported and will return a 0 for the
Counter values.
VALUE DESCRIPTION
1 Transmit
2 Receivero INTEGER .1.3.6.1.4.1.181.2.2.2.10.8.1.1 |
dsRpFrUrVcIndexThe VC index to the FRIB Ur Table. The
table has 64 entries for indiviual VCsro INTEGER .1.3.6.1.4.1.181.2.2.2.10.8.1.2 |
dsRpFrUrVcThe VC for this entry in the FRIB Ur Table.ro INTEGER .1.3.6.1.4.1.181.2.2.2.10.8.1.3 |
dsRpFrUrCIRExceededThe number of times the CIR threshold was exceeded, but
the EIR threshold was not crossed.ro Counter .1.3.6.1.4.1.181.2.2.2.10.8.1.4 |
dsRpFrUrCIRExceededOctetsThe number of octets that exceeded the CIR threshold,
but were less then the EIR threshold.ro Counter .1.3.6.1.4.1.181.2.2.2.10.8.1.5 |
dsRpFrUrEIRExceededThe number of times the EIR threshold was exceeded.ro Counter .1.3.6.1.4.1.181.2.2.2.10.8.1.6 |
dsRpFrUrEIRExceededOctetsThe number of octets that exceeded the EIR threshold.ro Counter .1.3.6.1.4.1.181.2.2.2.10.8.1.7 |
dsRpDdsDuration.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.181.2.2.2.11 |
dsRpDdsTableThis is the table of DDS statistical data. SEQUENCE OF DsRpDdsEntry .1.3.6.1.4.1.181.2.2.2.12 |
dsRpDdsEntryThis is an entry in the DDS Table. DsRpDdsEntry .1.3.6.1.4.1.181.2.2.2.12.1 |
dsRpDdsIfIndexThe index into the table. This is mib-II's ifIndex.ro INTEGER .1.3.6.1.4.1.181.2.2.2.12.1.1 |
dsRpDdsAvailableSecs.ro Counter32 .1.3.6.1.4.1.181.2.2.2.12.1.2 |
dsRpDdsTotalSecs.ro Counter32 .1.3.6.1.4.1.181.2.2.2.12.1.3 |
dsRpDdsBPVs.ro Counter32 .1.3.6.1.4.1.181.2.2.2.12.1.4 |
dsLm OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.3 |
dsLmLoopbackThis is the type of loopback that is currently
active. The values have the following meanings:
VALUE DESCRIPTION
lmLbkNone(1) No loopback is set
lmLbkLine(2) Line loopback is set
lmLbkPayload(3) Payload loopback is set
lmLbkLocal(4) Local loopback is set
lmLbkTiTest(5) TI looback is set
lmLbkDp1(6) Data port 1 loopback is set
lmLbkDp2(7) Data port 2 loopback is set
lmLbkDt1(8) Data terminal loopback on data
port 1 is set
lmLbkDt2(9) Data terminal loopback on data
port 2 is set
lmLbkCsu(10) CSU Loopback (DDS)
lmLbkDsu(11) DSU Loopback (DDS)
lmLbkDpdt(12) Data-Port/Data-Terminal LBrw Enumeration .1.3.6.1.4.1.181.2.2.3.1 |
dsLmSelfTestStateThis object will start a self test operation when
set to lmSelfTestStart(2). At the completion of the
test, it will return to its normal state of
lmSelfTestIdle(1).rw Enumeration .1.3.6.1.4.1.181.2.2.3.2 |
dsLmSelfTestResultsThe results of the last self test operation.ro DisplayString .1.3.6.1.4.1.181.2.2.3.3 |
dsRm OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.4 |
dsRmLbkCodeThe type of remote loopback that is currently set.
The possible values are:
VALUE DESCRIPTION
rmRNone(1) No loopback is set
rmRst1(2) A remote loopback reset code is
currenlty being sent
rmRLine(3) A remote Line loopback is set
rmRPayload(4) A remote Payload loopback is set
rmRDp1(5) A remote Data Port 1 loopback is set
rmRDp2(6) A remote Data Port 2 loopback is setrw Enumeration .1.3.6.1.4.1.181.2.2.4.1 |
dsRmTestCodeThe type of remote test code that is currently being
sent. The possible values are:
VALUE DESCRIPTION
rmTestNone(1) No test code is being sent
rmTestQrs(2) QRS is being sent
rmTest324(3) 3-in-24 is being sent
rmTestOnes(4) All ones is being sent
rmTestZeros(5) All zeros is being sent
rmTest511Dp1(6) 511 is being sent out data port 1
rmTest511Dp2(7) 511 is being sent out data port 2
rmTest2047Dp1(8) 2047 is being sent out data port 1
rmTest2047Dp2(9) 2047 is being sent out data port 2
rmTest2toThe23(10) 2 to the 23 is being sent
rmTest2toThe15(11) 2 to the 15 is being sentrw Enumeration .1.3.6.1.4.1.181.2.2.4.2 |
dsRmBertStateThe current BERT state. The possible values are:
VALUE DESCRIPTION
rmBertIdle(1) No BERT test is active
rmBertOtherStart(2) BERT was started from the control
port, front panel, or Telnet
rmBertSearching(3) BERT was started from the agent
and has not yet detected the code
rmBertFound(4) BERT was started from the agent
and has detected the codero Enumeration .1.3.6.1.4.1.181.2.2.4.3 |
dsRmBertCodeThis object controls the activation of BERT tests.
The possible values are:
VALUE DESCRIPTION
rmBertNone(1) No BERT test is active
rmBertQrs(2) BERT for QRS
rmBert324(3) BERT for 3-in-24
rmBertOnes(4) BERT for all ones
rmBertZeros(5) BERT for all zeros
rmBert511Dp1(6) BERT for 511 on data port 1
rmBert511Dp2(7) BERT for 511 on data port 2
rmBert2047Dp1(8) BERT for 2047 on data port 1
rmBert2047Dp2(9) BERT for 2047 on data port 2
rmTest2toThe23(10) BERT for 2 to the 23
rmTest2toThe15(11) BERT for 2 to the 15rw Enumeration .1.3.6.1.4.1.181.2.2.4.4 |
dsRmBertTestSecsThe number of seconds the requested test code has
been detected since the start of the BERT.ro INTEGER .1.3.6.1.4.1.181.2.2.4.5 |
dsRmBertBitErrorsThe number of bit errors detected since the start
of the BERT.ro INTEGER .1.3.6.1.4.1.181.2.2.4.6 |
dsRmBertErrdSecsThe number of errored seconds detected since the
start of the BERT.ro INTEGER .1.3.6.1.4.1.181.2.2.4.7 |
dsRmBertTotalErrorsThe number of total errors detected since the start
of the BERT.ro INTEGER .1.3.6.1.4.1.181.2.2.4.8 |
dsRmBertReSyncThe number of times BERT has lost and
re-aquired the pattern.ro INTEGER .1.3.6.1.4.1.181.2.2.4.9 |
dsRmFping OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.4.10 |
dsRmFpingActionThe control actions for the FPING test. Possible
values are:
VALUE DESCRIPTION
rmFpingStart(1) Start sending FPINGs
rmFpingStop(2) Stop sending FPINGsrw Enumeration .1.3.6.1.4.1.181.2.2.4.10.1 |
dsRmFpingStateThe current state of the FPING tester. Possible
values are:
VALUE DESCRIPTION
rmFpingIdle(1) No FPINGs are being generated
rmFpingOtherStart(2) FPINGs are being generated.
The test was started via one
of the other management
interfaces.
rmFpingRunning(3) FPINGs are being generated.
The test was started via SNMP.ro Enumeration .1.3.6.1.4.1.181.2.2.4.10.2 |
dsRmFpingVcThe VC that FPINGs will be sent on. VC values
range from (0..1023) if the Frame Relay address
length is 2 octets and (0..8388607) if the address
length is 4 octets. Default is 500.rw INTEGER .1.3.6.1.4.1.181.2.2.4.10.3 |
dsRmFpingFreqThe frequency (in seconds) that FPING packets will
be transmitted. The range is (5..255). Default is 5.rw INTEGER .1.3.6.1.4.1.181.2.2.4.10.4 |
dsRmFpingLenThe length (in octets) of the payload portion
of the FPING packets. The range is (0..1400).
Default is 0.rw INTEGER .1.3.6.1.4.1.181.2.2.4.10.5 |
dsRmFpingCurThe roundtrip time (in msec) of the last FPING sent.ro INTEGER .1.3.6.1.4.1.181.2.2.4.10.6 |
dsRmFpingMinThe minimum roundtrip time (in msec) of all
FPINGs sent during this test.ro INTEGER .1.3.6.1.4.1.181.2.2.4.10.7 |
dsRmFpingMaxThe maximum roundtrip time (in msec) of all
FPINGs sent during this test.ro INTEGER .1.3.6.1.4.1.181.2.2.4.10.8 |
dsRmFpingAvgThe average roundtrip time (in msec) of all
FPINGs sent during this test.ro INTEGER .1.3.6.1.4.1.181.2.2.4.10.9 |
dsRmFpingLostThe number of FPING packets lost during
this test.ro INTEGER .1.3.6.1.4.1.181.2.2.4.10.10 |
dsRmFpingTotalThe total number of FPING packets transmitted
during this test.ro INTEGER .1.3.6.1.4.1.181.2.2.4.10.11 |
dsRmFpingRmtVcThe VC used at the remote end of the circuit.ro DisplayString .1.3.6.1.4.1.181.2.2.4.10.12 |
dsRmFpingRmtIpThe IP address of the unit responding to FPINGs.ro IpAddress .1.3.6.1.4.1.181.2.2.4.10.13 |
dsRmInsertBitErrorPossible values are:
VALUE DESCRIPTION
insertBitError(1) Start sending FPINGs
noInsertBitError(2) Stop sending FPINGsrw Enumeration .1.3.6.1.4.1.181.2.2.4.11 |
dsAc OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.5 |
dsAcAlmMsgThis object controls the displaying/sending of
alarm messages. Alarm messages will be sent in the
format determined by dsAcAlmFormat if dsAcAlmMsg is
set to acAlmMsgEnable(1). Alarm messages will not be
sent if this object is set to acAlmMsgDisable(2).rw Enumeration .1.3.6.1.4.1.181.2.2.5.1 |
dsAcYelAlmThis object determines if incoming Yellow Alarm
will cause an alarm message to be sent. Setting this
object to acYelAlmEnable(1) causes an alarm to be
sent when Yellow Alarm is received on the Network
or Terminal Interface. Setting this object to
acYelAlmDisable(2) will not send an alarm when
Yellow Alarm is received.rw Enumeration .1.3.6.1.4.1.181.2.2.5.2 |
dsAcDeactThis object controls the number of seconds an
alarm condition must remain clear before the unit
declares it cleared. The range is from 0 to 15
seconds.rw INTEGER ( 1..15 ) .1.3.6.1.4.1.181.2.2.5.3 |
dsAcEstThis object determines the threshold of errored
seconds that triggers an Excessive Error Rate (EER)
alarm. Setting this object to zero disables errored
seconds causing an EER alarm.rw INTEGER ( 0..900 ) .1.3.6.1.4.1.181.2.2.5.4 |
dsAcUstThis object determines the threshold of uavailable
seconds that triggers an Excessive Error Rate (EER)
alarm. Setting this object to zero disables unavailable
seconds causing an EER alarm.rw INTEGER ( 0..900 ) .1.3.6.1.4.1.181.2.2.5.5 |
dsAcStThis object determines the window used to calculate
whether an Excessive Error Rate (EER) alarm should be
generated from errored seconds or unavailable seconds.
Setting this object to acSt15(1) establishes a
15-minute sliding window. Setting this object to
acSt60(2) establishes a 60-minute sliding window.rw Enumeration .1.3.6.1.4.1.181.2.2.5.6 |
dsAcBerAlmThis object controls the sending of a Bit Error
Rate (BER) alarm. The possible values are:
VALUE DESCRIPTION
acBerAlmEnable(1) Enable sending BER alarms
acBerAlmDisable(2) Disable sending BER alarmsrw Enumeration .1.3.6.1.4.1.181.2.2.5.7 |
dsAcRfaAlmThis object controls the sending of a Remote Frame
Alarm (RFA). The possible values are:
VALUE DESCRIPTION
acRfaAlmEnable(1) Enable sending RFA alarms
acRfaAlmDisable(2) Disable sending RFA alarmsrw Enumeration .1.3.6.1.4.1.181.2.2.5.8 |
dsAcAisAlmThis object controls the sending of Alarm Indication
Signal (AIS) alarms. The possible values are:
VALUE DESCRIPTION
acAisAlmEnable(1) Enable sending AIS alarms
acAisAlmDisable(2) Disable sending AIS alarmsrw Enumeration .1.3.6.1.4.1.181.2.2.5.9 |
dsCc OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.6 |
dsCcEchoThis object controls character echo on the
control port. The possible values are:
VALUE DESCRIPTION
ccEchoEnable(1) Enable control port echo
ccEchoDisable(2) Disable control port echorw Enumeration .1.3.6.1.4.1.181.2.2.6.1 |
dsCcControlPortThis object determines whether the control port
is the DCE or DTE port. The possible values are:
VALUE DESCRIPTION
ccDce(1) The control port is the DCE port
ccDte(2) The control port is the DTE portrw Enumeration .1.3.6.1.4.1.181.2.2.6.2 |
dsCcBaudThe baud rate of the control port. The possible
values are:
VALUE DESCRIPTION
cc2400(1) 2400 baud
cc9600(2) 9600 baud
cc19200(3) 19200 baud
cc38400(4) 38400 baudro Enumeration .1.3.6.1.4.1.181.2.2.6.3 |
dsCcParityThe parity of the control port. The possible
values are:
VALUE DESCRIPTION
ccNone(1) No parity
ccEven(2) Even parity
ccOdd(3) Odd parityro Enumeration .1.3.6.1.4.1.181.2.2.6.4 |
dsCcDataBitsThe number of data bits for the control port. The
possible values are:
VALUES DESCRIPTION
cc7Bit(1) 7 data bits
cc8Bit(2) 8 data bitsro Enumeration .1.3.6.1.4.1.181.2.2.6.5 |
dsCcStopBitsThe number of stop bits for the control port. The
possible values are:
VALUE DESCRIPTION
cc1Bit(1) 1 stop bit
cc2Bit(2) 2 stop bitsro Enumeration .1.3.6.1.4.1.181.2.2.6.6 |
dsCcDceInThe input status of the DCE signals RTS and DTR.
The possible valuesa re:
VALUE DESCRIPTION
ccBothOff(1) RTS off, DTR off
ccRtsOnDtrOff(2) RTS on, DTR off
ccRtsOffDtrOn(3) RTS off, DTR on
ccBothOn(4) RTS on, DTR onro Enumeration .1.3.6.1.4.1.181.2.2.6.7 |
dsCcDteInThe input status of the DTE signals CTS and DCD.
The possible values are:
VALUE DESCRIPTION
ccBothOff(1) CTS off, DCD off
ccCtsOnDcdOff(2) CTS on, DCD off
ccCTSoffDCDon(3) CTS off, DCD on
ccBothOn(4) CTS on, DCD onro Enumeration .1.3.6.1.4.1.181.2.2.6.8 |
dsDc OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.7 |
dsDcTableThe Data Port Configuration Table. This table
contains information on the configuration of each
of the unit's data ports. SEQUENCE OF DsDcEntry .1.3.6.1.4.1.181.2.2.7.1 |
dsDcEntryAn entry in the Data Port Configuration Table. DsDcEntry .1.3.6.1.4.1.181.2.2.7.1.1 |
dsDcIndexThe index to the Data Port Configuration Table.
The possible values are 1 through 2.ro INTEGER .1.3.6.1.4.1.181.2.2.7.1.1.1 |
dsDcDataInvertThe data inversion of the data port. The possible
values are:
VALUE DESCRIPTION
dcDataInvertEnable(1) Invert the data port signal
dcDataInvertDisable(2) Don't invert the data port
signalrw Enumeration .1.3.6.1.4.1.181.2.2.7.1.1.2 |
dsDcInterfaceThe type of electrical interface the data port is
using. The possible values are:
VALUE DESCRIPTION
dcV35Interface(1) V.35
dcEia530Interface(2) EIA-530
dcV35DSInterface (3) V.35 DataSMART Compatiblerw Enumeration .1.3.6.1.4.1.181.2.2.7.1.1.3 |
dsDcClockSourceThe clock source for the data port. The possible
values are:
VALUE DESCRIPTION
dcInternalClock(1) Use the internal clock
dcExternalClock(2) Use the external clockrw Enumeration .1.3.6.1.4.1.181.2.2.7.1.1.4 |
dsDcXmtClkInvertThe inversion status of the transmit clock signal
for the data port. The possible values are:
VALUE DESCRIPTION
dcXClkInvertEnable(1) Invert the transmit clock
signal
dcXClkInvertDisable(2) Don't invert the transmit
clock signalrw Enumeration .1.3.6.1.4.1.181.2.2.7.1.1.5 |
dsDcRcvClkInvertThe inversion status of the received clock signal
for the data port. The possible values are:
VALUE DESCRIPTION
dcRClkInvertEnable(1) Invert the received clock
signal
dcRClkInvertDisable(2) Don't invert the received
clock signalrw Enumeration .1.3.6.1.4.1.181.2.2.7.1.1.6 |
dsDcIdleCharThe idle character to use for the data port. The
possible values are:
VALUE DESCRIPTION
dc7eIdleChar(1) The idle character is hex 7E
dc7fIdleChar(1) The idle character is hex 7F
dcffIdleChar(3) The idle character is hex FFrw Enumeration .1.3.6.1.4.1.181.2.2.7.1.1.7 |
dsDcLOSInputThe combination of RTS and DTR that will cause a
data port Loss of Signal alarm. The possible
values are:
VALUE DESCRIPTION
dcLosNone(1) Data port LOS is disabled
dcLosRts(2) LOS is declared when RTS is lost
dcLosDtr(3) LOS is declared when DTR is lost
dcLosBoth(4) LOS is declared when both RTS and DTR
are lost.rw Enumeration .1.3.6.1.4.1.181.2.2.7.1.1.8 |
dsFc OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.8 |
dsFcLoadXcuteThe Fractional Table that is active. The possible
values are:
VALUE DESCRIPTION
fcLoadXcuteIdle(1) The normal state
fcLoadXcuteStartA(2) Load and execute table A
fcLoadXcuteStartB(3) Load and execute table Brw Enumeration .1.3.6.1.4.1.181.2.2.8.1 |
dsFcTableThis is the DS1/E1 Fractional Table. This table
consists of configuration information about
DS1/E1 fractional services. SEQUENCE OF DsFcEntry .1.3.6.1.4.1.181.2.2.8.2 |
dsFcEntryThis is an entry in the Fractional Table. DsFcEntry .1.3.6.1.4.1.181.2.2.8.2.1 |
dsFcTableIndexThis is the index into the Fractional Table. The
possible values are:
VALUE DESCRIPTION
1 Stored configuration A
2 Stored configuration B
3 Currently executing fractional tablero INTEGER .1.3.6.1.4.1.181.2.2.8.2.1.1 |
dsFcChanIndexThis is the index of the fractional channel.
DS1 has 24 channels and E1 has 32.ro INTEGER .1.3.6.1.4.1.181.2.2.8.2.1.2 |
dsFcChanMapThe destination and data rate of the channel. The
possible values are:
VALUE DESCRIPTION
fcChanIdle(1) The channel is idle
fcChanTiData(2) The channel carries data and is
mapped to a TI channel
fcChanTiVoice(3) The channel carries voice and
is mapped to a TI channel
fcChan56Dp1(4) The cahnnel is set for 56K and is
mapped to data port 1
fcChan64Dp1(5) The channel is set for 64K and is
mapped to data port 1
fcChan56Dp2(6) The channel is set for 56K and is
mapped to data port 2
fcChan64Dp2(7) The channel is set for 64K and is
mapped to data port 2
fcChanDLNK(8) The channel is idle and set for
data link communications
fcChanDPDL(9) The channel is active and also
set for data link communications
fCchanUanv(10) The channel is unavailablerw Enumeration .1.3.6.1.4.1.181.2.2.8.2.1.3 |
dsFcMap16This object determines if channel 16 is available
for user payload data. This is only possible if the
unit is configured for Common Channel Signalling.
The possible values are:
VALUE DESCRIPTION
fcMap16Used(1) Channel 16 cannot be used for
user payload data
fcMap16Unused(2) Channel 16 is available for user
payload datarw Enumeration .1.3.6.1.4.1.181.2.2.8.3 |
dsFmc OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.9 |
dsFmcFrameTypeThe frame type for packets being transmitted and
received for IP connectivity.
The possible values are:
VALUE DESCRIPTION
fmcFrNlpid(1) Frame Relay NLPID encapsulation
fmcFrEther(2) Frame Relay Ethertype encapsulation
fmcAtmNlpid(3) ATM DXI NLPID encapsulation
fmcAtmLlcSnap(4) ATM DXI LLC/SNAP encapsulation
fmcAtmVcMux(5) ATM DXI VC-based multiplexingrw Enumeration .1.3.6.1.4.1.181.2.2.9.1 |
dsFmcAddrOctetsThe length in octets of the Frame Relay address.
The possible values are:
VALUE DESCRIPTION
fmc2Octets(1) The address is 2 octets long
fmc4Octets(1) The address is 4 octets longrw Enumeration .1.3.6.1.4.1.181.2.2.9.2 |
dsFmcFcsBitsThe length in bits of the Frame Relay FCS.
The possible values are:
VALUE DESCRIPTION
fmc16Bits(1) The FCS field is 16 bits long
fmc32Bits(2) The FCS field is 32 bits longrw Enumeration .1.3.6.1.4.1.181.2.2.9.3 |
dsFmcUpperBWThe percent of bandwidth utilization threshold. If
the threshold is exceeded, an event will be recorded
in the performance data and a trap (if configured)
will be sent. Valid values are 5-95 in increments
of 5.rw INTEGER .1.3.6.1.4.1.181.2.2.9.4 |
dsFmcFpingOperThe enabling and disabling of FPING operation.
Valid values are Enable and Disable.rw Enumeration .1.3.6.1.4.1.181.2.2.9.5 |
dsFmcFpingGenThe number of distinct VC to be received on the NI
before FPINGs are automatically sent out.rw INTEGER .1.3.6.1.4.1.181.2.2.9.6 |
dsFmcFpingThresThe maximum roundtrip time of a FPING packet in
milliseconds. If the threshold is exceeded, an
event will be recorded in the performance data and
a trap (if configured) will be sent. Valid values
are 20-2000 in increments of 10.rw INTEGER .1.3.6.1.4.1.181.2.2.9.7 |
dsFmcFpingRstReset the specified VC to an initial state where
FPING connectivity is check for. Valid values are
0-1023 for a 2 octet address field and 0-8388607
for a 4 octet address field.rw INTEGER .1.3.6.1.4.1.181.2.2.9.8 |
dsFmcAddVcAdd a VC to the list of monitored VCsrw INTEGER .1.3.6.1.4.1.181.2.2.9.9 |
dsFmcDelVcDel a VC from the list of monitored VCs. Any
statistics related to this VC will be moved to
the 'other' category.rw INTEGER .1.3.6.1.4.1.181.2.2.9.10 |
dsMc OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.10 |
dsMcNetifThe management access port(s) for Telnet and SNMP.
The possible values are:
VALUE DESCRIPTION
mcNetNone(1) No ip interface paths are active
mcNetEthernet(2) The ethernet ip interface is active
mcNetPppSlip(3) The ppp/slip (control ports)
ip interfaces are active
mcNetSlip(4) The slip (control ports) ip interface
is active
mcNetDatalink(5) The data link ip interface is active
mcNetES(6) The ethernet and slip (control ports)
ip interfaces are active
mcNetED(7) The ethernet and data link
ip interfaces are active
mcNetESD(8) The ethernet, slip (control ports), and
data link ip interfaces are active
mcNetPSD(9) The ppp/slip (control ports) and
data link ip interfaces are active
mcNetSD(10) The slip (control ports) and data link
ip interfaces are active
mcNetInband(11) The inband Frame Relay (NI and Data
Port) ip interface is activerw Enumeration .1.3.6.1.4.1.181.2.2.10.1 |
dsMcT1DLPathThe T1 DataLink value. This configuration is used if
the NETIF has a DataLink component.
The possible values are:
VALUE DESCRIPTION
mcDLPathFdl(1) The DataLink will use the FDL.
mcDLPathTSn-64 The DataLink will use TSn. If TSn
is IDLE, the data rate will be set
to 64K. If TSn is assigned to a
Data Port, the DataLink will use
8K of TSn.
mcDLPathTSn-56 The DataLink will use TSn. If TSn
is IDLE, the data rate will be set
to 56K. If TSn is assigned to a
Data Port, the DataLink will use
8K of TSn.rw Enumeration .1.3.6.1.4.1.181.2.2.10.2 |
dsMcDefRouteThe unit's default IP router.rw IpAddress .1.3.6.1.4.1.181.2.2.10.3 |
dsMcCIpAddrThe IP address for the unit's Control Port.rw IpAddress .1.3.6.1.4.1.181.2.2.10.4 |
dsMcDIpAddrThe IP address for the unit's Data Link.rw IpAddress .1.3.6.1.4.1.181.2.2.10.5 |
dsMcCDIpMaskThe IP subnet mask for the unit's Control Port and
Data Link.rw IpAddress .1.3.6.1.4.1.181.2.2.10.6 |
dsMcEIpAddrThe IP address for the unit's Ethernet Port.rw IpAddress .1.3.6.1.4.1.181.2.2.10.7 |
dsMcEIpMaskThe IP subnet mask for the unit's Ethernet Port.rw IpAddress .1.3.6.1.4.1.181.2.2.10.8 |
dsMcIIpAddrThe IP address for the unit's In-Band Interface.rw IpAddress .1.3.6.1.4.1.181.2.2.10.9 |
dsMcIIpMaskThe IP subnet mask for the unit's In-Band Interface.rw IpAddress .1.3.6.1.4.1.181.2.2.10.10 |
dsAmc OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.10.11 |
dsAmcAgentThe operational status of the SMMP agent. The
possible values are:
VALUE DESCRIPTION.
amcEnabled(1) The SNMP agent is enabled
amcDisabled(2) The SNMP agent is disabled.rw Enumeration .1.3.6.1.4.1.181.2.2.10.11.1 |
dsAmcSourceScreenThe status of the IP source address screening
security. The possible values are:
VALUE DESCRIPTION
mcIpScreen(1) The screening security is enabled
mcNoScreen(2) The screening security is disabledrw Enumeration .1.3.6.1.4.1.181.2.2.10.11.2 |
dsAmcTrapTableThe SNMP Trap Table. This table lists the different
types of traps and allows each type to be individually
enabled/disabled. Currently, the types of traps are:
Start Traps - Cold-Start and Warm-Start
Link Traps - Link-Up and Link-Down Traps
Authentication Traps - e.g. incorrect Telnet password
Enterprise Traps - e.g. NI EER Trap SEQUENCE OF DsAmcTrapEntry .1.3.6.1.4.1.181.2.2.10.11.3 |
dsAmcTrapEntryAn entry in the SNMP Trap Table. DsAmcTrapEntry .1.3.6.1.4.1.181.2.2.10.11.3.1 |
dsAmcTrapTypeThe type of trap. There is one row in dsAmcTrapTable
for each type of trap.
The possible values are:
VALUE DESCRIPTION
amcStartTraps(1)
Cold-Start and Warm-Start Traps.
amcLinkTraps(2)
Link-Up and Link-Down Traps.
amcAuthenTraps(3)
Authentication Traps. Sent for:
- Incorrect Telnet password
- Source IP address not on IP Screen List
- Incorrect SNMP Read Community String
- Incorrect SNMP Write Community String
amcEnterpriseTraps(4)
Enterprise-Specific Traps.ro Enumeration .1.3.6.1.4.1.181.2.2.10.11.3.1.1 |
dsAmcTrapStatusIndicates whether the particular type of trap is
enabled or disabled.
The possible values are:
VALUE DESCRIPTION
amcEnabled(1)
These types of traps are enabled.
amcDisabled(2)
These types of traps are disabled.rw Enumeration .1.3.6.1.4.1.181.2.2.10.11.3.1.2 |
dsAmcScrnTableThe Source Address Screening Table. The entries
in this table are the IP addresses which are
allowed to access this unit. SEQUENCE OF DsAmcScrnEntry .1.3.6.1.4.1.181.2.2.10.11.4 |
dsAmcScrnEntryAn entry in the Source Address Screening Table. DsAmcScrnEntry .1.3.6.1.4.1.181.2.2.10.11.4.1 |
dsAmcScrnIndexThe index to the Source Address Screening Table.
Ten entries are possible.ro INTEGER .1.3.6.1.4.1.181.2.2.10.11.4.1.1 |
dsAmcScrnIpAddrAn IP Address(es) which will be permitted to access this
unit. This object is combined with dsAmcScrnIpMask to
allow a single entry to permit access by an
entire subnet.rw IpAddress .1.3.6.1.4.1.181.2.2.10.11.4.1.2 |
dsAmcScrnIpMaskAn IP subnet mask that indicates which portion
of dsAmcScrnIpAddr must be matched to permit access.
This allows a single entry to provide access by an
entire IP subnet.
A mask of '255.255.255.0' means that hosts on
the subnet of dsAmcScrnIpAddr are permitted access.
A mask of '255.255.255.255' means that only the
IP address which exactly matches dsAmcScrnIpAddr is
permitted access (i.e. only a single host).rw IpAddress .1.3.6.1.4.1.181.2.2.10.11.4.1.3 |
dsAmcTrapDestTableThe SNMP Trap Destinations Table. This table lists
up to 10 addresses to send SNMP traps to when
alarm conditions occur. SEQUENCE OF DsAmcTrapDestEntry .1.3.6.1.4.1.181.2.2.10.11.5 |
dsAmcTrapDestEntryAn entry in the SNMP Trap Destinations Table. DsAmcTrapDestEntry .1.3.6.1.4.1.181.2.2.10.11.5.1 |
dsAmcTrapDestIndexThe index to the SNMP Trap Destinations Table.ro INTEGER .1.3.6.1.4.1.181.2.2.10.11.5.1.1 |
dsAmcTrapDestIpAddrThe IP address portion of a Trap Destination Entry,
used when sending SNMP traps.rw IpAddress .1.3.6.1.4.1.181.2.2.10.11.5.1.2 |
dsAmcTrapDestVcThe VC portion of a Trap Destination Entry,
used when sending SNMP traps.rw INTEGER .1.3.6.1.4.1.181.2.2.10.11.5.1.3 |
dsAmcTrapDestPortThe Port portion of a Trap Destination Entry,
used when sending SNMP traps.rw Enumeration .1.3.6.1.4.1.181.2.2.10.11.5.1.4 |
dsMcIVcfill in later.rw DLCI .1.3.6.1.4.1.181.2.2.10.12 |
dsMcIPortfill in later
The possible values are:
VALUE DESCRIPTION
amcNiPort(1) Communicate over NI
amcDPPort(2) communicate over DPrw Enumeration .1.3.6.1.4.1.181.2.2.10.13 |
dsNc OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.11 |
dsNcFramingThe type of framing being used on the Network
Interface. The possible values are:
VALUE DESCRIPTION
ncSF(1) SF (D4) framing
ncESF(2) ESF framing
ncEricsson(3) Ericsson framingrw Enumeration .1.3.6.1.4.1.181.2.2.11.1 |
dsNcCodingThe type of line coding being used on the Network
Interface. The possible values are:
VALUE DESCRIPTION
ncAmi(1) AMI line coding
ncB8zs(2) B8ZS line coding.rw Enumeration .1.3.6.1.4.1.181.2.2.11.2 |
dsNcT1403This object enables/disables the sending of
T1.403 PRM messages. The possible values are:
VALUE DESCRIPTION
ncT1403Enable(1) Enable T1.403 messages
ncT1403Disable(2) Disabled T1.403 messagesrw Enumeration .1.3.6.1.4.1.181.2.2.11.3 |
dsNcYellowThis object enables/disables sending Yellow alarm
out the Network Interface upon receipt of an
alarm on the Network Interface. The possible values
are:
VALUE DESCRIPTION
ncYelEnable(1) Enable sending Yellow alarm
ncYelDisable(1) Disable sending Yellow alarmrw Enumeration .1.3.6.1.4.1.181.2.2.11.4 |
dsNcAddr54If 54016 addressing is enabled, this object
determines what type of addressing the unit responds
to. The possible values are:
VALUE DESCRIPTION
ncAddrCsu(1) CSU addressing mode
ncAddrDsu(2) DSU addressing mode
ncAddrBoth(3) Both CSU and DSU addressing modesrw Enumeration .1.3.6.1.4.1.181.2.2.11.5 |
dsNc54016This object determines whether the unit responds to
54016 addressing modes. The possible values are:
VALUE DESCRIPTION
nc54016Enable(1) Enabled 54016 addressing
nc54016Disable(2) Disable 54016 addressingrw Enumeration .1.3.6.1.4.1.181.2.2.11.6 |
dsNcLboThe Network Interface Line Build Out setting.
The possible values are:
VALUE DESCRIPTION
ncLbo0(1) 0.0dB line attenuation
ncLbo1(2) 7.5dB line attenuation
ncLbo2(3) 15.0 dB line attenuationrw Enumeration .1.3.6.1.4.1.181.2.2.11.7 |
dsNcMF16The E1 network interface Time Slot 16 MultiFrame
alignment signal setting. The possible values are:
VALUE DESCRIPTION
ncMF16Enable(1) Enable the Time Slot 16 MultiFrame
alignment signal
ncMF16Disable(2) Disabled the Time Slot 16 MultiFrame
alignment signalrw Enumeration .1.3.6.1.4.1.181.2.2.11.8 |
dsNcCRCThe E1 network interface CRC generation/checking
setting. The possible values are:
VALUE DESCRIPTION
ncCrcEnable(1) Enable CRC generation/checking
ncCrcDisable(2) Disable CRC generation/checkingrw Enumeration .1.3.6.1.4.1.181.2.2.11.9 |
dsNcFasAlignThe E1 network interface Time Slot 0 NOT-FAS Word
setting. The possible values are:
VALUE DESCRIPTION
ncFasWord(1) Use the NOT-FAS word
ncNonFasWord(2) Do not use the NOT-FAS wordrw Enumeration .1.3.6.1.4.1.181.2.2.11.10 |
dsNcE1DLPathThe E1 network interface Sa bit usage. If Sa bits
are being used for data link communications, both the
near and far end units must agree on which Sa bit to
use. Possible value are:
VALUE DESCRIPTION
ncSaNone(1) No Sa bits are being used for
data link communications
ncSaBit4(2) Use Sa bit 4 for data link
communications
ncSaBit5(3) Use Sa bit 5 for data link
communications
ncSaBit6(4) Use Sa bit 6 for data link
communications
ncSaBit7(5) Use Sa bit 7 for data link
communications
ncSaBit8(6) Use Sa bit 8 for data link
communications
ncTSn Use TimeSlot n for data link
communications. These are only
available for E1 units with
In-Band Link hardware.rw Enumeration .1.3.6.1.4.1.181.2.2.11.11 |
dsNcKAThe status of sending E1 remote Frame Alarm into
the NI during alarms. The Possible values are:
VALUE DESCRIPTION
ncFramedKeepAlive(1) Enable Framed Keep Alive
ncUnFramedKeepAlive(2) Disabled Unframed Keep Aliverw Enumeration .1.3.6.1.4.1.181.2.2.11.12 |
dsNcGenRfaThe status of sending E1 remote Frame Alarm into
the NI during alarms. The Possible values are:
VALUE DESCRIPTION
ncGenRfaEnable(1) Enable RFA insertion
ncGenRfaDisable(2) Disabled RFA insertionrw Enumeration .1.3.6.1.4.1.181.2.2.11.13 |
dsNcPassTiRfaThe status of sending the RFA received on the
network interface out the terminal interface. This
function is not possible on a DSU only, it must be
an add/drop. This function only works if at least one
channel is assigned to the TI. The Possible values are:
VALUE DESCRIPTION
ncPassTiRfaEnable(1) Enable RFA re-generation
ncPassTiRfaDisable(2) Disabled RFA re-generationrw Enumeration .1.3.6.1.4.1.181.2.2.11.14 |
dsNcIdleThe idle code to be transmited in the idle NI and TI
channels. This code is also sent in all TI channels
when the TI is experiencing an OOF.rw INTEGER ( 0..255) .1.3.6.1.4.1.181.2.2.11.15 |
dsNcDdsTypeThe Possible values are:
VALUE DESCRIPTION
scDds56K(1) Set unit to 56K Operation
scDds64K(2) Set unit to 56K Operationrw Enumeration .1.3.6.1.4.1.181.2.2.11.16 |
dsSc OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.12 |
dsScMonthThe calendar number of the current month.
1 is January.rw INTEGER .1.3.6.1.4.1.181.2.2.12.1 |
dsScDayThe number of the current day.rw INTEGER .1.3.6.1.4.1.181.2.2.12.2 |
dsScYearThe number of the current year. 95 is 1995.rw INTEGER .1.3.6.1.4.1.181.2.2.12.3 |
dsScHourThe number of the current hour. 0 is 12:00am.rw INTEGER .1.3.6.1.4.1.181.2.2.12.4 |
dsScMinutesThe number of the current minute.rw INTEGER .1.3.6.1.4.1.181.2.2.12.5 |
dsScNameThe Site Name of the unit.rw DisplayString .1.3.6.1.4.1.181.2.2.12.6 |
dsScSlotAddrThe Kentrox-specific slot address.
The 01 in the address 01:02:003.rw INTEGER .1.3.6.1.4.1.181.2.2.12.7 |
dsScShelfAddrThe Kentrox-specific shelf address.
The 02 in the address 01:02:003.rw INTEGER .1.3.6.1.4.1.181.2.2.12.8 |
dsScGroupAddrThe Kentrox-specific group address.
The 003 in the address 01:02:003.rw INTEGER .1.3.6.1.4.1.181.2.2.12.9 |
dsScFrontPanelThe status of the front panel buttons. The
possible values are:
VALUE DESCRIPTION
scFpEnable(1) Enable the front panel buttons
scFpDisable(2) Disable the front panel buttonsrw Enumeration .1.3.6.1.4.1.181.2.2.12.10 |
dsScDSCompatibleThe status of the datasmart compatibility function.
This should be set to scDSEnabled(1) when the far
end unit is a eariler model datasmart, not a
datasmart. The possible values are:
VALUE DESCRIPTION
scDSEnable(1) Enable the datasmart compatibility
function
scDSDisable(2) Disable the datasmart compatibility
funcationrw Enumeration .1.3.6.1.4.1.181.2.2.12.11 |
dsScClockSourceThe source of the timing clock. The various options
are:
VALUE DESCRIPTION
scTerminalTiming(1) Use the clock coming in on
the Terminal Interface
scThroughTiming(2) Use Through timing NI rx
to Ti tx and TI rx to NI tx
scInternalTiming(3) Use the internal clock
scLoopTiming(4) Use the clock from the network
scDP1Timing(5) Use the clock coming in on
data port 1
scDP2Timing(6) Use the clock coming in on
data port 2rw Enumeration .1.3.6.1.4.1.181.2.2.12.12 |
dsScAutologoutThe time (in minutes) to wait for a keypress
before logging the current user out. If this object
is set to 0, autologout is disabled.rw INTEGER .1.3.6.1.4.1.181.2.2.12.13 |
dsScZeroPerDataThis object will zero all performance report
counters if it is set to scZallStart(2).rw Enumeration .1.3.6.1.4.1.181.2.2.12.14 |
dsScWyvThe string returned by the user interface command
WYV, What's Your Version.ro DisplayString .1.3.6.1.4.1.181.2.2.12.15 |
dsScAutoCfgThis object enables/disables the Auto-Configuration
feature, which allows units in a daisy chain to be
automatically configured by the Daisy Chain Controller.
This feature is only available on the plug-in
versions of datasmart.rw Enumeration .1.3.6.1.4.1.181.2.2.12.16 |
dsScTftpSwdlA text string used to initiate or check the status of a TFTP
file transfer operation for doing a software download. To
initiate a TFTP software download, set this variable to the
value `tswdl:<i>,<f>`, where i represents the IP address of
the host system, and the f represents the name of the file to
be downloaded. Setting this variable to any other value will
have no affect. Getting the value of this variable will
return the status of the TFTP software download.rw DisplayString .1.3.6.1.4.1.181.2.2.12.17 |
dsScBootThis variable is used to force a system reboot:
scBootIdle Does nothing.
scBootActive Reboots from the executing FLASH ROM bank.
scBootInactive Reboots from the non-executing FLASH ROM bank.rw Enumeration .1.3.6.1.4.1.181.2.2.12.18 |
dsScOperModefill in later.
scTransparentMode Unit doesn't monitor FR traffic
scMonitorMode Unit monitors FR trafficrw Enumeration .1.3.6.1.4.1.181.2.2.12.19 |
dsScYearExtention.rw INTEGER ( 1992..2091 ) .1.3.6.1.4.1.181.2.2.12.20 |
dsScMonthExtention.rw INTEGER ( 1..12 ) .1.3.6.1.4.1.181.2.2.12.21 |
dsScDayExtention.rw INTEGER ( 1..31 ) .1.3.6.1.4.1.181.2.2.12.22 |
dsScHourExtention.rw INTEGER ( 0..24 ) .1.3.6.1.4.1.181.2.2.12.23 |
dsScMinExtention.rw INTEGER ( 0..59 ) .1.3.6.1.4.1.181.2.2.12.24 |
dsScSecExtention.ro INTEGER ( 0..59 ) .1.3.6.1.4.1.181.2.2.12.25 |
dsScPinK.rw Enumeration .1.3.6.1.4.1.181.2.2.12.26 |
dsTc OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.13 |
dsTcFramingThe line framing for the Terminal Interface.
The possible values are:
VALUE DESCRIPTION
tcSF(1) SF (D4) framing
tcESF(2) ESF framing
tcEricsson(3) Ericsson framingrw Enumeration .1.3.6.1.4.1.181.2.2.13.1 |
dsTcCodingThe line coding for the Terminal Interface.
The possible values are:
VALUE DESCRIPTION
tcAmi(1) AMI line coding
tcB8zs(2) B8ZS line codingrw Enumeration .1.3.6.1.4.1.181.2.2.13.2 |
dsTcIdleThe code that is sent out the idle DS0 channels
of the terminal interface.rw INTEGER ( 0..255) .1.3.6.1.4.1.181.2.2.13.3 |
dsTcEqualThe line equalization for the Terminal Interface. The
possible values are:
VALUE DESCRIPTION
tcTe0(1) 0-133 feet
tcTe1(2) 133-266 feet
tcTe2(3) 266-399 feet
tcTe3(4) 399-533 feet
tcTe4(5) 533-655 feetrw Enumeration .1.3.6.1.4.1.181.2.2.13.4 |
dsTcMF16The E1 terminal interface Time Slot 16 MultiFrame
alignment signal setting. The possible values are:
VALUE DESCRIPTION
tcMF16Enable(1) Enable the Time Slot 16 MultiFrame
alignment signal
tcMF16Disable(2) Disabled the Time Slot 16 MultiFrame
alignment signalrw Enumeration .1.3.6.1.4.1.181.2.2.13.5 |
dsTcCRCThe E1 terminal interface CRC generation/checking
setting. The possible values are:
VALUE DESCRIPTION
tcCrcEnable(1) Enable CRC generation/checking
tcCrcDisable(2) Disable CRC generation/checkingrw Enumeration .1.3.6.1.4.1.181.2.2.13.6 |
dsTcFasAlignThe E1 terminal interface Time Slot 0 NOT-FAS Word
setting. The possible values are:
VALUE DESCRIPTION
tcFasWord(1) Use the NOT-FAS word
tcNonFasWord(2) Do not use the NOT-FAS wordrw Enumeration .1.3.6.1.4.1.181.2.2.13.7 |
dsTcAisThis object controls the sending of Alarm Indication
Signal (AIS) alarms. The possible values are:
VALUE DESCRIPTION
tcAisEnable(1) Enable sending AIS alarms
tcAisDisable(2) Disable sending AIS alarmsrw Enumeration .1.3.6.1.4.1.181.2.2.13.8 |
dsTcGenRfaThe status of sending E1 remote Frame Alarm into
the TI during alarms. The Possible values are:
VALUE DESCRIPTION
tcGenRfaEnable(1) Enable RFA insertion
tcGenRfaDisable(2) Disabled RFA insertionrw Enumeration .1.3.6.1.4.1.181.2.2.13.9 |
dsTcPassTiRfaThe status of sending the RFA received on the
terminal interface out the network interface. This
function is not possible on a DSU only, it must be
an add/drop. This function only works if at least one
channel is assigned to the TI. The Possible values are:
VALUE DESCRIPTION
tcPassTiRfaEnable(1) Enable RFA re-generation
tcPassTiRfaDisable(2) Disabled RFA re-generationrw Enumeration .1.3.6.1.4.1.181.2.2.13.10 |
dsFp OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.14 |
dsFpFr56 OBJECT IDENTIFIER .1.3.6.1.4.1.181.2.2.14.1 |
dsFpFr56PwrLedThe current state of the FP PWR LED.
The Possible values are:
VALUE DESCRIPTION
fpLedIndeterminate (1) LED is not present on unit
fpLedOff (2) LED is OFF
fpLedOnGreen (3) LED is ON and green
fpLedBlinkGreen (4) LED is blinking greenro Enumeration .1.3.6.1.4.1.181.2.2.14.1.1 |
dsFpFr56DnldFailLedThe current state of the FP DNLD/FAIL LED.
The Possible values are:
VALUE DESCRIPTION
fpLedIndeterminate (1) LED is not present on unit
fpLedOff (2) LED is OFF
fpLedOnRed (3) LED is ON and red
fpLedBlinkRed (4) LED is blinking redro Enumeration .1.3.6.1.4.1.181.2.2.14.1.2 |
dsFpFr56NiAlarmLedThe current state of the FP NI ALARM LED.
The Possible values are:
VALUE DESCRIPTION
fpLedIndeterminate (1) LED is not present on unit
fpLedOff (2) LED is OFF
fpLedOnRed (3) LED is ON and redro Enumeration .1.3.6.1.4.1.181.2.2.14.1.3 |
dsFpFr56NiDataLedThe current state of the FP NI DATA LED.
The Possible values are:
VALUE DESCRIPTION
fpLedIndeterminate (1) LED is not present on unit
fpLedOff (2) LED is OFF
fpLedOnGreen (3) LED is ON and greenro Enumeration .1.3.6.1.4.1.181.2.2.14.1.4 |
dsFpFr56TestLedThe current state of the FP TEST LED.
The Possible values are:
VALUE DESCRIPTION
fpLedIndeterminate (1) LED is not present on unit
fpLedOff (2) LED is OFF
fpLedOnYellow (3) LED is ON and yellowro Enumeration .1.3.6.1.4.1.181.2.2.14.1.5 |
dsFpFr56DpCtsTxLedThe current state of the FP DP CTS TX LED.
The Possible values are:
VALUE DESCRIPTION
fpLedIndeterminate (1) LED is not present on unit
fpLedOff (2) LED is OFF
fpLedOnYellow (3) LED is ON and yellowro Enumeration .1.3.6.1.4.1.181.2.2.14.1.6 |
dsFpFr56DpRtsRxLedThe current state of the FP DP RTS RX LED.
The Possible values are:
VALUE DESCRIPTION
fpLedIndeterminate (1) LED is not present on unit
fpLedOff (2) LED is OFF
fpLedOnYellow (3) LED is ON and yellowro Enumeration .1.3.6.1.4.1.181.2.2.14.1.7 |
dsFpFr56FrLinkLedThe current state of the FP FRAME RELAY LINK LED.
The Possible values are:
VALUE DESCRIPTION
fpLedIndeterminate (1) LED is not present on unit
fpLedOff (2) LED is OFF
fpLedOnGreen (3) LED is ON and green
fpLedBlinkGreen (4) LED is blinking greenro Enumeration .1.3.6.1.4.1.181.2.2.14.1.8 |