DASAN-SHDSL-MIB
AI MIB Summary
The DASAN-SHDSL-MIB module extends the standard SHDSL-LINE-MIB to monitor proprietary G.SHDSL line parameters and scalar capabilities specific to DASAN hardware. It provides granular visibility into line status, performance counters, and device capabilities through the `dsShdslCapabilityGroup` and extended tables for operational management of G.SHDSL access equipment.
The MIB module to describe G.SHDSL product. The MIB module that provides objects that are proprietary and extension to SHDSL- LINE-MIB. The MIB include extension to following Tables. The MIB also include a set of scalar(s) clubbed under the group 'dsShdslCapabilityGroup'.
Main OID:
dasanShdslMIB.1.3.6.1.4.1.6296.9.6
112
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
112 total| Object Name |
|---|
dasanShdslMIBThe MIB module to describe G.SHDSL product. The MIB module that provides objects that are proprietary and extension to SHDSL- LINE-MIB. The MIB include extension to following Tables. The MIB also include a set of scalar(s) clubbed under the group 'dsShdslCapabilityGroup'. MODULE-IDENTITY .1.3.6.1.4.1.6296.9.6 |
dasanShdslLineMIB OBJECT IDENTIFIER .1.3.6.1.4.1.6296.9.6.1 |
dasanShdslMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.6296.9.6.1.1 |
dsShdslCapabilityGroup OBJECT IDENTIFIER .1.3.6.1.4.1.6296.9.6.1.1.1 |
dsShdslCapabilityLineTxCapThis bitmap specifies the transmission modes that the STU-C is capable of supporting. Right now, support for Annex A (q9921PotsNonOverlapped(2) and q9921PotsOverlapped(3)) is present. This value depends on the DSL PHY firmware present on Columbia MxU.ro Bits .1.3.6.1.4.1.6296.9.6.1.1.1.1 |
dsShdslLineStatusTableThis MO is proprietary extension of RFC 3276 MIB and contains the proprietary line status. SEQUENCE OF DsHdsl2ShdslLineStatusEntry .1.3.6.1.4.1.6296.9.6.1.1.2 |
dsShdslLineStatusEntryAn entry (conceptual row) in the dsShdslLineStatusTable. The Table is indexed by ifIndex. DsHdsl2ShdslLineStatusEntry .1.3.6.1.4.1.6296.9.6.1.1.2.1 |
dsShdslOpStateThis object identifies the high level operational state for the STU.ro Enumeration .1.3.6.1.4.1.6296.9.6.1.1.2.1.1 |
dsShdslStartProgressThis object identifies the current detailed operational state of the STU.ro Enumeration .1.3.6.1.4.1.6296.9.6.1.1.2.1.2 |
dsShdslFwReleaseTransceiver firmware release number.ro OCTET STRING (SIZE ( 0..255 ) ) .1.3.6.1.4.1.6296.9.6.1.1.2.1.3 |
dsShdslLineSwapThis object indicates if the physical lines are swapped, i.e., logical channel A is connected to physical channel B. This applies to 4-wire operation only.ro Enumeration .1.3.6.1.4.1.6296.9.6.1.1.2.1.4 |
dsShdslRmtCountryCodeThis object provides the country code word, as defined in ITU-T G.991.2, for the STU at the other end of the loop. GlobespanVirata sets this to USA.ro OCTET STRING (SIZE ( 0..255 ) ) .1.3.6.1.4.1.6296.9.6.1.1.2.1.5 |
dsShdslRmtEncoderAThis object identifies the 21-bit value corresponding to encoder coefficient A, as defined in ITU-T G.991.2, for the STU at the other end of the loop.ro INTEGER .1.3.6.1.4.1.6296.9.6.1.1.2.1.6 |
dsShdslRmtEncoderBThis object identifies the 21-bit value corresponding to encoder coefficient B, as defined in ITU-T G.991.2, for the STU at the other end of the loop.ro INTEGER .1.3.6.1.4.1.6296.9.6.1.1.2.1.7 |
dsShdslRmtProviderCodeThis object identifies the provider code word, as defined in ITU-T G.991.2, for the STU at the other end of the loop.ro OCTET STRING (SIZE ( 0..255 ) ) .1.3.6.1.4.1.6296.9.6.1.1.2.1.8 |
dsShdslLocDetectThis object is used to determine if carrier has been lost.ro INTEGER .1.3.6.1.4.1.6296.9.6.1.1.2.1.9 |
dsShdslTxPowerThis object identifies the local STU transmit power in tenths of a dBm.ro INTEGER .1.3.6.1.4.1.6296.9.6.1.1.2.1.10 |
dsShdslFramerSyncThis object returns information regarding the framer synchronization status.ro Enumeration .1.3.6.1.4.1.6296.9.6.1.1.2.1.11 |
dsShdslRmtTomDataThis object provides vendor-provided data, as defined in ITU-T G.991.2, for the STU at the other end of the loop.ro INTEGER .1.3.6.1.4.1.6296.9.6.1.1.2.1.12 |
dsShdslDriftAlarmThis object identifies if the receive clock is in or out of range.ro INTEGER .1.3.6.1.4.1.6296.9.6.1.1.2.1.13 |
dsShdslReceiverGainThis object provides the total receiver gain in dB.ro INTEGER .1.3.6.1.4.1.6296.9.6.1.1.2.1.14 |
dsShdslBertErrorThis object provides the count of bit errors since the last time the object was read, as well as the type of synchronization.ro Enumeration .1.3.6.1.4.1.6296.9.6.1.1.2.1.15 |
dsShdslFramerOHAndDefectsThis object returns overhead data. The four least significant bits contain the overhead data in the following format: bit 0 is losd, bit 1 is sega, bit 2 is ps, and bit 3 is segd.ro OCTET STRING (SIZE ( 0..10 ) ) .1.3.6.1.4.1.6296.9.6.1.1.2.1.16 |
dsShdslRmtFwVersionThis object provides the transceiver firmware release number of the STU at the other end of the loop.ro INTEGER .1.3.6.1.4.1.6296.9.6.1.1.2.1.17 |
dsShdslUtopiaCellDelineationThis object indicates whether cell delineation has been found.ro Enumeration .1.3.6.1.4.1.6296.9.6.1.1.2.1.18 |
dsShdslUtopiaRxCellCntThis object indicates the number of UTOPIA cells received since the last time the object has been called. The maximum value is 0xFFFF.ro INTEGER .1.3.6.1.4.1.6296.9.6.1.1.2.1.19 |
dsShdslUtopiaCellDropCntThis object indicates the number of UTOPIA cells dropped since the last time the object has been called. The maximum value is 0xFF.ro INTEGER .1.3.6.1.4.1.6296.9.6.1.1.2.1.20 |
dsShdslUtopiaRxHecErrorCntThis object indicates the number of UTOPIA cells with HEC errors since the last time the object has been called. The maximum value is 0xFF.ro INTEGER .1.3.6.1.4.1.6296.9.6.1.1.2.1.21 |
dsShdslUtopiaTxCellCntThis object indicates the number of UTOPIA cells transmitted since the last time the object has been called. The maximum value is 0xFFFF.ro INTEGER .1.3.6.1.4.1.6296.9.6.1.1.2.1.22 |
dsShdslRmtNsfCusIdThis object returns the customer identification that was sent by the STU at the other end of the loop.ro INTEGER .1.3.6.1.4.1.6296.9.6.1.1.2.1.23 |
dsShdslRmtNsfCusDataThis object returns non-standard format customer data that was sent by the STU at the other end of the loop.ro OCTET STRING (SIZE ( 0..4 ) ) .1.3.6.1.4.1.6296.9.6.1.1.2.1.24 |
dsShdslLocalHandshakeThis object provides a way to see what capabilities are supported by the local STU. A total of 26 handshake parameters are supported.ro OCTET STRING (SIZE ( 0..52 ) ) .1.3.6.1.4.1.6296.9.6.1.1.2.1.25 |
dsShdslRemoteHandshakeThis object provides a way to see what capabilities are supported by the STU at the other end of the loop. A total of 26 handshake parameters are supported.ro OCTET STRING (SIZE ( 0..52 ) ) .1.3.6.1.4.1.6296.9.6.1.1.2.1.26 |
dsShdslActualHandshakeThis object provides the results of capabilities exchanged during handshake. A total of 26 handshake parameters are supported.ro OCTET STRING (SIZE ( 0..52 ) ) .1.3.6.1.4.1.6296.9.6.1.1.2.1.27 |
dsShdslRmtTxPowerThis object provides the transmit power of the STU at the other end of the loop.ro INTEGER .1.3.6.1.4.1.6296.9.6.1.1.2.1.28 |
dsShdslRmtPowerBackoffThis object indicates whether power backoff is enabled or disabled at the STU at the other end of the loop.ro Enumeration .1.3.6.1.4.1.6296.9.6.1.1.2.1.29 |
dsShdslAutoRetrainCountThis object indicates the number of automatic retrains. This counter is only reset when a startup is initiated.ro INTEGER .1.3.6.1.4.1.6296.9.6.1.1.2.1.30 |
dsShdslEocStateThis object provides status information about the eoc stage.ro Enumeration .1.3.6.1.4.1.6296.9.6.1.1.2.1.31 |
dsShdslFramerOneSecondCntThis object provides CRC, SEGA, and LOSW defect one second error counts, and should be called every second.ro OCTET STRING (SIZE ( 0..6 ) ) .1.3.6.1.4.1.6296.9.6.1.1.2.1.32 |
dsShdslNtrFaultThis object identifies the Network Timing Recovery Fault.ro Enumeration .1.3.6.1.4.1.6296.9.6.1.1.2.1.33 |
dsShdslCpeMasterCorero Enumeration .1.3.6.1.4.1.6296.9.6.1.1.2.1.34 |
dsShdslParametricTestResultIndicates the Result of the Parametric Test conducted on the Xcvr.ro Enumeration .1.3.6.1.4.1.6296.9.6.1.1.2.1.35 |
dsShdslParametricTestArrayConexant parameter that indicates the Parametric Test Array.ro OCTET STRING (SIZE ( 0..1024 ) ) .1.3.6.1.4.1.6296.9.6.1.1.2.1.36 |
dsShdslLineParamsTableThis MO is proprietary extension of RFC 3276 MIB and contains the proprietary line parameters. SEQUENCE OF DsHdsl2ShdslLineParamsEntry .1.3.6.1.4.1.6296.9.6.1.1.3 |
dsShdslLineParamsEntryAn entry (conceptual row) in the dsShdslLineParamsTable. The Table is indexed by ifIndex. DsHdsl2ShdslLineParamsEntry .1.3.6.1.4.1.6296.9.6.1.1.3.1 |
dsShdslActionThis object specifies actions that are used to control transceiver operation.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.1 |
dsShdslModeThis object specifies the operational mode of the transceiver.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.2 |
dsShdslPowerScaleThis object is used to compensate for minor differences in transmit power between designs.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.3 |
dsShdslFramerTypeThis object defines which type of data interface type is used. Note that the non-default values only apply to Conexant chips that support serial interfaces.ro Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.4 |
dsShdslAFETypeThis objects defines which AFE is being used.ro Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.5 |
dsShdslEncodeCoeffAThis object determines the value of encoder coefficient A, as defined in ITU-T G.991.2.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.6 |
dsShdslEncodeCoeffBThis object determines the value of encoder coefficient B, as defined in ITU-T G.991.2rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.7 |
dsShdslTxEOCBufferLenThis object determines the number of bytes of EOC data that is buffered by the DSP in the transmit direction.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.8 |
dsShdslRxEOCBufferLenThis object determines the number of bytes of EOC data that is buffered by the DSP in the receive direction.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.9 |
dsShdslNTRThis object defines how network-timing recovery is performed.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.10 |
dsShdslRxUpstreamFrameSyncCustomer-defined value. This object defines the upstream frame sync word.rw INTEGER .1.3.6.1.4.1.6296.9.6.1.1.3.1.11 |
dsShdslRxDownstreamFrameSyncThis object defines the downstream frame sync word.rw INTEGER .1.3.6.1.4.1.6296.9.6.1.1.3.1.12 |
dsShdslRxUpstreamStuffBitsCustomer-defined value. This object defines the upstream.rw INTEGER .1.3.6.1.4.1.6296.9.6.1.1.3.1.13 |
dsShdslRxDownstreamStuffBitsThis object defines the downstream stuff bits.rw INTEGER .1.3.6.1.4.1.6296.9.6.1.1.3.1.14 |
dsShdslInitiateThis object defines which STU initiates a startup. The default is STU-R initiates and STU-C waits.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.15 |
dsShdslFramerRxClockModeThis object determines the source of the receive clock.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.16 |
dsShdslFramerRxPllModeThis object enables or disables the internal PLL.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.17 |
dsShdslSerialAtmCiuBufferSizeThis object enables the user to set the size of the framer buffer for serial ATM operation.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.18 |
dsShdslUtopiaL2TxAddressThis object selects the appropriate UTOPIA Level 2 address for the transmit interface.ro INTEGER .1.3.6.1.4.1.6296.9.6.1.1.3.1.19 |
dsShdslUtopiaL2RxAddressThis object selects the appropriate UTOPIA Level 2 address for the receive interface.ro INTEGER .1.3.6.1.4.1.6296.9.6.1.1.3.1.20 |
dsShdslTxFramerPulseDelayThis parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, a delay of up to 7 clock cycles can be specified for the transmit frame pulse.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.21 |
dsShdslRxFramerPulseDelayThis parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, a delay of up to 7 clock cycles can be specified for the receive frame pulse.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.22 |
dsShdslMultiFrameModeThis object specifies the multi frame operational mode of the transceiver.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.23 |
dsShdslEnable4or6MbpsBitrateThis object specifies the operational state of the 4_6Mbps bit rate.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.24 |
dsShdslTomDataWord1This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.rw INTEGER .1.3.6.1.4.1.6296.9.6.1.1.3.1.25 |
dsShdslTomDataWord2This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.rw INTEGER .1.3.6.1.4.1.6296.9.6.1.1.3.1.26 |
dsShdslTomDataWord3This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.rw INTEGER .1.3.6.1.4.1.6296.9.6.1.1.3.1.27 |
dsShdslTomDataWord4This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.rw INTEGER .1.3.6.1.4.1.6296.9.6.1.1.3.1.28 |
dsShdslSetReqSilenceModeThis object enables a silent mode for the STU at the opposite end of the loop for approximately one minute. During the silent period, the STU that requested the silent mode could perform whatever operations it wants and the STU at the opposite end will remain in handshake.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.29 |
dsShdslSetIndividualRates1This item enables the user to individually enable or disable base rates for N=1 through N=16. The default is all rates enabled.rw INTEGER .1.3.6.1.4.1.6296.9.6.1.1.3.1.30 |
dsShdslSetIndividualRates2This item enables the user to individually enable or disable base rates for N=17 through N=32. The default is all rates enabled.rw INTEGER .1.3.6.1.4.1.6296.9.6.1.1.3.1.31 |
dsShdslSetIndividualRates3This item enables the user to individually enable or disable base rates for N=33 through N=36. The default is all rates enabled.rw INTEGER .1.3.6.1.4.1.6296.9.6.1.1.3.1.32 |
dsShdslSatmCellDelineationThis object enables the user to enable or disable cell delineation for serial ATM operation. This parameter should be set before a startup.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.33 |
dsShdslFramerCellDropOnErrorThis object determines whether cells are dropped, i.e., not passed to the host, or not dropped, i.e., passed to the host. This object must be set prior to startup.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.34 |
dsShdslGearShiftTypeThis object specifies the Gear Shift Type.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.35 |
dsShdslHsNsfThis object enables or disables nonstandard Information fields for MP, MS, CL, and CLR messages, as defined in ITU-T G.994.1.bis.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.36 |
dsShdslHsMaxBitsPerBaudThis object specifies the maximum bit per baud.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.37 |
dsShdslHsCusIdThis object identifies the customer identification during handshaking, as described in ITU-T G.994.1.bis.rw INTEGER .1.3.6.1.4.1.6296.9.6.1.1.3.1.38 |
dsShdslHsCusData0This object identifies two words of customer data during handshaking, as defined in ITU-T G.994.1.bis.rw INTEGER .1.3.6.1.4.1.6296.9.6.1.1.3.1.39 |
dsShdslHsCusData1This object identifies two words of customer data during handshaking, as defined in ITU-T G.994.1.bis.rw INTEGER .1.3.6.1.4.1.6296.9.6.1.1.3.1.40 |
dsShdslHsAnnexBTypeThis object allows the customer to choose between support for Annex B, Annex B with Access Network Frequency Plan (ANFP), or both.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.41 |
dsShdslAutoRetrainEnables or disables auto-retrain.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.42 |
dsShdslArCrcCheckEnables or disables auto-retrain based on CRC errors.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.43 |
dsShdslArFramerSyncCheckEnables or disables auto-retrain based on framer synchronization.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.44 |
dsShdslArSnrMarginCheckEnables or disables auto-retrain based on whether the S/N margin falls below a preset threshold.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.45 |
dsShdslArCrcThresholdSets the threshold for the number of frames with CRC errors for autoretrain.rw INTEGER ( 0..1024 ) .1.3.6.1.4.1.6296.9.6.1.1.3.1.46 |
dsShdslArSnrMarginThresholdSet the margin threshold for autoretrain.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.47 |
dsShdslArRetrainTimeSets the time over which the autoretrain parameters must be outside their normal ranges, so that an auto-retrain occurs.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.48 |
dsShdslOpStateTrapEnableEnables/disables trap indicating a change in op state.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.49 |
dsShdslTxFrmrDataClkEdgeThis parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, transmit data can be sampled upon either rising or falling edge of the transmit clock.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.50 |
dsShdslRxFrmrDataClkEdgeThis parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, receive data can be valid upon either rising or falling edge of the receive clock.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.51 |
dsShdslTxFrmrPulseClkEdgeThis parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be active upon either rising or falling edge.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.52 |
dsShdslRxFrmrPulseClkEdgeThis parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be active upon either rising or falling edge.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.53 |
dsShdslTxFrmrPulseLvlThis parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be either active high (1) or active low (0).rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.54 |
dsShdslRxFrmrPulseLvlThis parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be either active high (1) or active low (0).rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.55 |
dsShdslUtopiaDataBusWidthThis parameter is used to specify width of UTOPIA data bus.ro Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.56 |
dsShdslFrmrOHThis object specifies framer OverHead Channel.rw INTEGER ( 0..65535 ) .1.3.6.1.4.1.6296.9.6.1.1.3.1.57 |
dsShdslLoopAttenCrossingTrapEnableThis Parameter enables or disables the Trap for Loop Attenuation Threshold crossing.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.58 |
dsShdslSNRMarginCrossingTrapEnableThis Parameter enables or disables the Trap for SNR Margin Threshold crossing.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.59 |
dsShdslFramerOHAndDefectsTrapEnableThis Parameter enables or disables the Trap for Framer Overhead and Defects.rw Enumeration .1.3.6.1.4.1.6296.9.6.1.1.3.1.60 |
dsShdslParametricTestInputFileIndicates Name of the Input file from which to take the Mask Array Size, lower and upper mask Array. Null string means no file is specified.rw DisplayString (SIZE ( 0..56 ) ) .1.3.6.1.4.1.6296.9.6.1.1.3.1.61 |
dsShdslParamHybridLossTestStartIndicates Start bin for range of bins to be measured. The default value mentioned is an indicative value only, for exact value refer to document number DO-400523-AN and DO-401163-AN.rw INTEGER ( 0..255 ) .1.3.6.1.4.1.6296.9.6.1.1.3.1.62 |
dsShdslParamHybridLossTestEndIndicates End bin for range of bins to be measured. The default value mentioned is an indicative value only.rw INTEGER ( 0..255 ) .1.3.6.1.4.1.6296.9.6.1.1.3.1.63 |
dsShdslSpanStatusExtnTableThis table is a proprietary extension of hdsl2ShdslSpanStatusTable SEQUENCE OF GsvHdsl2ShdslSpanStatusExtnEntry .1.3.6.1.4.1.6296.9.6.1.1.4 |
dsShdslSpanStatusExtnEntryAn entry (conceptual row) in the dsShdslSpanStatusExtnTable. The Table is indexed by ifIndex. GsvHdsl2ShdslSpanStatusExtnEntry .1.3.6.1.4.1.6296.9.6.1.1.4.1 |
dsShdslStatusPMMSMaxLineRateThis object provides the maximum PMMS rate the line is capable of achievingro Unsigned32 ( 0..4112000 ) .1.3.6.1.4.1.6296.9.6.1.1.4.1.1 |
dsShdslStatus4WireHsModeContains the current 4 Wire Handshake Mode Configuredro Enumeration .1.3.6.1.4.1.6296.9.6.1.1.4.1.2 |