CRESCENDO-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
65
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
65 total| Object Name |
|---|
crescendo OBJECT IDENTIFIER .1.3.6.1.4.1.203 |
RFC1155-SMI Unknown .1.3.6.1.4.1.203 |
crescendoProducts OBJECT IDENTIFIER .1.3.6.1.4.1.203.1 |
concentrator OBJECT IDENTIFIER .1.3.6.1.4.1.203.1.1 |
conc OBJECT IDENTIFIER .1.3.6.1.4.1.203.1.1.1 |
concMgmtTypeThe type of network management running on the
concentrator.ro Enumeration .1.3.6.1.4.1.203.1.1.1.1 |
concIpAddrThe concentrator's IP address.rw IpAddress .1.3.6.1.4.1.203.1.1.1.2 |
concNetMaskThe concentrator's subnet mask.rw IpAddress .1.3.6.1.4.1.203.1.1.1.3 |
concBroadcastThe concentrator's broadcast address.rw IpAddress .1.3.6.1.4.1.203.1.1.1.4 |
concTrapReceiverTableThe concentrator trap receiver table (0 to 10 entries).
This table lists the addresses of Network Management
Stations that should receive trap messages from this
concentrator when an exception condition occurs. SEQUENCE OF ConcTrapReceiverEntry .1.3.6.1.4.1.203.1.1.1.5 |
concTrapReceiverEntryA trap receiver table entry. ConcTrapReceiverEntry .1.3.6.1.4.1.203.1.1.1.5.1 |
concTrapReceiverTypeSetting this object to invalid(2) removes the
corresponding entry from the concTrapReceiverTable.
To add a new entry to the concTrapReceiverTable,
set the concTrapReceiverAddr to an IpAddress which is
not already in the table. The concTrapReceiverType for
that entry is automatically set to other(1).rw Enumeration .1.3.6.1.4.1.203.1.1.1.5.1.1 |
concTrapReceiverAddrIP address for trap receiver.rw IpAddress .1.3.6.1.4.1.203.1.1.1.5.1.2 |
concTrapReceiverCommCommunity string used for trap messages to this trap
receiver.rw DisplayString .1.3.6.1.4.1.203.1.1.1.5.1.3 |
concCommunityTableThe concentrator community table (4 entries). This
table lists community strings and their access levels.
When an SNMP message is received by this concentrator,
the community string in the message is compared with
this table to determine access rights of the sender. SEQUENCE OF ConcCommunityEntry .1.3.6.1.4.1.203.1.1.1.6 |
concCommunityEntryA community table entry. ConcCommunityEntry .1.3.6.1.4.1.203.1.1.1.6.1 |
concCommunityAccessA value of readWriteAll(4) allows the community to read
and write all objects in the MIB. A value of readWrite(3)
allows the community to read and write all objects except
the concCommunityTable, which it cannot access at all.
A value of readOnly(2) allows the community to read all
objects except the concCommunityTable. A value of
other(1) allows no access.ro Enumeration .1.3.6.1.4.1.203.1.1.1.6.1.1 |
concCommunityStringConfigurable community string with access rights
defined by the value of concCommunityAccess.rw DisplayString .1.3.6.1.4.1.203.1.1.1.6.1.2 |
concAttachTypeThe requested concentrator attachment type. For a dual
attachment concentrator connected to the trunk ring,
port 1 on the supervisor module (or single board
concentrator) is configured as A and port 2 is
configured as B. For a single attachment concentrator
connected beneath another concentrator, port 1 is
configured as S and port 2 is configured as M. For a
null attachment concentrator at the root of the tree,
ports 1 and 2 are configured as M. This object does
not take effect until the concentrator is reset. The
current attachment type can be determined from
snmpFddiPORTPCType for ports 1 and 2. Note that a
concentrator with no MAC is always null attachment type.rw Enumeration .1.3.6.1.4.1.203.1.1.1.7 |
concTrafficThe percentage of bandwidth utilization on the network
for the previous polling interval.ro INTEGER .1.3.6.1.4.1.203.1.1.1.8 |
concResetWriting a 2 to this object resets the control logic of
all modules in the concentrator.rw Enumeration .1.3.6.1.4.1.203.1.1.1.9 |
concBaudRateThe baud rate in bits per second of the concentrator
RS-232 port.rw INTEGER .1.3.6.1.4.1.203.1.1.1.10 |
chassis OBJECT IDENTIFIER .1.3.6.1.4.1.203.1.1.2 |
chassisTypeThe chassis type.ro Enumeration .1.3.6.1.4.1.203.1.1.2.1 |
chassisBkplTypeThe chassis backplane type.ro Enumeration .1.3.6.1.4.1.203.1.1.2.2 |
chassisPs1TypeType of power supply number 1.ro Enumeration .1.3.6.1.4.1.203.1.1.2.3 |
chassisPs1StatusStatus of power supply number 1. If the status is not
ok, the value of chassisPs1TestResult gives more
detailed information about the power supply's failure
condition(s).ro Enumeration .1.3.6.1.4.1.203.1.1.2.4 |
chassisPs1TestResultTest result for power supply number 1. A zero
indicates that the supply passed all tests. Bits set
in the result indicate error conditions.ro INTEGER .1.3.6.1.4.1.203.1.1.2.5 |
chassisPs2TypeType of power supply number 2.ro Enumeration .1.3.6.1.4.1.203.1.1.2.6 |
chassisPs2StatusStatus of power supply number 2. If the status is not
ok, the value of chassisPs2TestResult gives more
detailed information about the power supply's failure
condition(s).ro Enumeration .1.3.6.1.4.1.203.1.1.2.7 |
chassisPs2TestResultTest result for power supply number 2. A zero
indicates that the supply passed all tests. Bits set
in the result indicate error conditions.ro INTEGER .1.3.6.1.4.1.203.1.1.2.8 |
chassisFanStatusStatus of the chassis fan. If the status is not ok,
the value of chassisFanTestResult gives more detailed
information about the fan's failure condition(s).ro Enumeration .1.3.6.1.4.1.203.1.1.2.9 |
chassisFanTestResultTest result for the chassis fan. A zero indicates
that the fan passed all tests. Bits set in the result
indicate error conditions.ro INTEGER .1.3.6.1.4.1.203.1.1.2.10 |
chassisMinorAlarmThe chassis minor alarm status.ro Enumeration .1.3.6.1.4.1.203.1.1.2.11 |
chassisMajorAlarmThe chassis major alarm status.ro Enumeration .1.3.6.1.4.1.203.1.1.2.12 |
chassisTempAlarmThe chassis temperature alarm status.ro Enumeration .1.3.6.1.4.1.203.1.1.2.13 |
chassisNumSlotsThe number of slots in the chassis for plug-in modules.ro INTEGER .1.3.6.1.4.1.203.1.1.2.14 |
chassisSlotConfigAn indication of which slots in the chassis have
modules inserted. This is an integer value with bits
set to indicate configured modules. It can be
interpreted as a sum of f(x) as x goes from 1 to the
number of slots, where f(x) = 0 module and f(x) =
exp(2, x-1) for a module inserted.ro INTEGER .1.3.6.1.4.1.203.1.1.2.15 |
module OBJECT IDENTIFIER .1.3.6.1.4.1.203.1.1.3 |
moduleTableA list of module entries. The number of entries is
given by the value of chassisNumSlots. SEQUENCE OF ModuleEntry .1.3.6.1.4.1.203.1.1.3.1 |
moduleEntryEntry containing information about one module in a
slot of the concentrator. ModuleEntry .1.3.6.1.4.1.203.1.1.3.1.1 |
moduleIndexA unique value for each module within the concentrator.
This value is determined by the chassis slot number
where the module is inserted. Valid entries are 1 to
the value of chassisNumSlotsro INTEGER .1.3.6.1.4.1.203.1.1.3.1.1.1 |
moduleTypeThe type of module.ro Enumeration .1.3.6.1.4.1.203.1.1.3.1.1.2 |
moduleSerialNumberThe serial number of the module.ro INTEGER .1.3.6.1.4.1.203.1.1.3.1.1.3 |
moduleHwHiVersionThe high part of the hardware version of the module.
For example, if the hardware version is 3.1, the value
of moduleHwHiVersion is 3.ro INTEGER .1.3.6.1.4.1.203.1.1.3.1.1.4 |
moduleHwLoVersionThe low part of the hardware version of the module.
For example, if the hardware version is 3.1, the value
of moduleHwLoVersion is 1.ro INTEGER .1.3.6.1.4.1.203.1.1.3.1.1.5 |
moduleFwHiVersionThe high part of the firmware version number. For
example, if the firmware version is 3.1, the value of
moduleFwHiVersion is 3.ro INTEGER .1.3.6.1.4.1.203.1.1.3.1.1.6 |
moduleFwLoVersionThe low part of the firmware version number. For
example, if the firmware version is 3.1, the value of
moduleFwLoVersion is 1.ro INTEGER .1.3.6.1.4.1.203.1.1.3.1.1.7 |
moduleSwHiVersionThe high part of the software version number. For
example, if the software version is 3.1, the value of
moduleSwHiVersion is 3.ro INTEGER .1.3.6.1.4.1.203.1.1.3.1.1.8 |
moduleSwLoVersionThe low part of the software version number. For
example, if the software version is 3.1, the value of
moduleSwLoVersion is 1.ro INTEGER .1.3.6.1.4.1.203.1.1.3.1.1.9 |
moduleStatusThe operational status of the module. If the status
is not ok, the value of moduleTestResult gives more
detailed information about the module's failure
condition(s).ro Enumeration .1.3.6.1.4.1.203.1.1.3.1.1.10 |
moduleTestResultThe result of the module's self test. A zero
indicates that the module passed all tests. Bits set
in the result indicate error conditions.ro INTEGER .1.3.6.1.4.1.203.1.1.3.1.1.11 |
moduleResetWriting a 2 to this object resets the module's
control logic. This has the same affect as pressing
the reset button on the module.rw Enumeration .1.3.6.1.4.1.203.1.1.3.1.1.12 |
moduleNameA descriptive string used by the network administrator
to name the module.rw DisplayString .1.3.6.1.4.1.203.1.1.3.1.1.13 |
moduleNumPortsThe number of ports supported by the module.ro INTEGER .1.3.6.1.4.1.203.1.1.3.1.1.14 |
modulePortStatusA series of bytes containing status information about
the module and each of the ports on the module. The
first byte contains the status for the module (same
value as moduleStatus), and subsequent bytes contain
status for the first through the last ports on the
module (same value as portStatus).ro OCTET STRING .1.3.6.1.4.1.203.1.1.3.1.1.15 |
port OBJECT IDENTIFIER .1.3.6.1.4.1.203.1.1.4 |
portTableA list of port entries. The number of entries is
determined by the number of modules in the concentrator
and the number of ports on each module. SEQUENCE OF PortEntry .1.3.6.1.4.1.203.1.1.4.1 |
portEntryEntry containing information for a particular port on
a module. PortEntry .1.3.6.1.4.1.203.1.1.4.1.1 |
portModuleIndexA unique value for each module within the concentrator.
This value is determined by the chassis slot number
which the module is plugged into. Valid entries are 1
to the value of chassisNumSlots.ro INTEGER .1.3.6.1.4.1.203.1.1.4.1.1.1 |
portIndexA unique value for each port within a module. This
value is determined by the location of the port on the
module. Valid entries are 1 to the value of
moduleNumPorts for this module.ro INTEGER .1.3.6.1.4.1.203.1.1.4.1.1.2 |
portFddiIndexThe snmpFddiPORTIndex for this module/port.ro INTEGER .1.3.6.1.4.1.203.1.1.4.1.1.3 |
portNameA descriptive string used by the network administrator
to name the port.rw DisplayString .1.3.6.1.4.1.203.1.1.4.1.1.4 |
portTypeThe type of physical layer medium dependent interface
on the port.ro Enumeration .1.3.6.1.4.1.203.1.1.4.1.1.5 |
portStatusThe operational status of the port. If the status is
not ok, the values of snmpFddiPORTCEState and
snmpFddiPORTConnectState give more detailed information
about the port's failure condition(s).ro Enumeration .1.3.6.1.4.1.203.1.1.4.1.1.6 |