CPQWCRM-MIB
Detailed view of the defined objects, syntax rules, and hierarchical paths.
134
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
134 total| Object Name |
|---|
cpqWcrm OBJECT IDENTIFIER .1.3.6.1.4.1.232.167 |
CPQHOST-MIB Unknown .1.3.6.1.4.1.232.167 |
alarmSensorInternalInternal Sensor Alarm TRAP-TYPE .1.3.6.1.4.1.232.167.0.1 |
alarmSensorWaterCoolUnitWater Cool Unit Sensor Alarm TRAP-TYPE .1.3.6.1.4.1.232.167.0.2 |
alarmInternalInternal Unit Alarm TRAP-TYPE .1.3.6.1.4.1.232.167.0.5 |
alarmWaterCoolUnitWater Cool Unit System Alarm TRAP-TYPE .1.3.6.1.4.1.232.167.0.6 |
testTrapTest trap sent to a trap receiver to check proper reception of traps TRAP-TYPE .1.3.6.1.4.1.232.167.0.10 |
cpqWcrmMibRev OBJECT IDENTIFIER .1.3.6.1.4.1.232.167.1 |
cpqWcrmMibMajRevThe Major Revision level.
A change in the major revision level represents a major change
in the architecture of the MIB. A change in the major revision
level may indicate a significant change in the information,
correct interpretation of data may require a MIB document
with the same major revision level.ro INTEGER .1.3.6.1.4.1.232.167.1.1 |
cpqWcrmMibMinRevThe Minor Revision level.
A change in the minor revision level may represent some minor
additional support, no changes to any pre-existing information
has occurred.ro INTEGER .1.3.6.1.4.1.232.167.1.2 |
cpqWcrmMibConditionThe overall condition (status) of the system represented by
this MIB.
(2) OK
(3) a minor problem, warning condition (yellow LED on Environmental Controller)
(4) a major problem (red LED on Environmental Controller)
(5) configuration of sensor units changed or
unit detected (red/yellow/green LED on Environmental Controller)ro Enumeration .1.3.6.1.4.1.232.167.1.3 |
cpqWcrmStatus OBJECT IDENTIFIER .1.3.6.1.4.1.232.167.2 |
cpqWcrmStatusDeviceEnvironmentalControllerGeneral Status of Environmental Controller unit itself
(1) failed
(2) OKro Enumeration .1.3.6.1.4.1.232.167.2.1 |
cpqWcrmUnitsConnectedNumber of sensor units connected to the Environmental Controller, Port 1 to 2ro INTEGER .1.3.6.1.4.1.232.167.2.2 |
cpqWcrmStatusSensorInternal OBJECT IDENTIFIER .1.3.6.1.4.1.232.167.2.3 |
cpqWcrmInternalTypeOfDeviceType of sensor unit connected to port 1ro Enumeration .1.3.6.1.4.1.232.167.2.3.1 |
cpqWcrmInternalTextDescriptional text for sensor unit connected to port 1rw DisplayString .1.3.6.1.4.1.232.167.2.3.2 |
cpqWcrmInternalSerialSerialnumber of sensor unit connected to port 1ro INTEGER .1.3.6.1.4.1.232.167.2.3.3 |
cpqWcrmInternalStatusGeneral Status sensor unit connected to port 1
(1) OK
(2) error, e. g. value overflow
(3) configuration of sensor unit has changed, confirmation required
(4) reset from sensor unit to confirm configuration changes
(5) timeout of sensor unit, confirmation required to unload this unit
(6) sensor unit detected, needs to be confirmed
(7) unit is not available
(8) supply voltage is too lowro Enumeration .1.3.6.1.4.1.232.167.2.3.4 |
cpqWcrmStatusInternalSensors OBJECT IDENTIFIER .1.3.6.1.4.1.232.167.2.3.5 |
cpqWcrmInternalNumberOfSensorsNumber of sensors connected to sensor unit 1ro INTEGER .1.3.6.1.4.1.232.167.2.3.5.1 |
cpqWcrmInternalSensorTableHeadline of sensor table SEQUENCE OF CpqWcrmInternalSensorEntry .1.3.6.1.4.1.232.167.2.3.5.2 |
cpqWcrmInternalSensorEntryEntries of sensor table CpqWcrmInternalSensorEntry .1.3.6.1.4.1.232.167.2.3.5.2.1 |
internalSensorIndexIndex for the list of value entries. Its value ranges
between 1 and the value of cpqWcrmInternalNumberOfSensors.ro INTEGER .1.3.6.1.4.1.232.167.2.3.5.2.1.1 |
internalSensorTypeType of sensor which is connected to internal sensor to sensor[internalSensorIndex]
1: no sensor connected
2: sensor failure
3: value overflow
4: sensor type 1, access sensor
5: sensor type 2, vibration sensor
6: sensor type 3, motion sensor
7: sensor type 4, smoke sensor
8: sensor type 5, air flow sensor
9: sensor type 6, reserved
10: sensor type 7, temperature sensor
11: sensor type 8, 4..20mA sensor
12: sensor type 9, humidity sensor
13: user sensor with normally opened contact
14: user sensor with normally closed contact
15: door locked sensor from locking device
16: remote unlock sensor (e.g. external keypad)
17: voltage sensor, indicates status of main voltage (OK, NOK)
18: voltage value
19: fan status, from Environmental Controller-FAS-Unit
20: leakage sensorro Enumeration .1.3.6.1.4.1.232.167.2.3.5.2.1.2 |
internalSensorTextDescriptional text for each sensor (entry in the table)rw DisplayString .1.3.6.1.4.1.232.167.2.3.5.2.1.3 |
internalSensorStatusActual status of the sensorro Enumeration .1.3.6.1.4.1.232.167.2.3.5.2.1.4 |
internalSensorValueValue of sensorro INTEGER .1.3.6.1.4.1.232.167.2.3.5.2.1.5 |
internalSensorSetHighValue for high setpoint of sensorrw INTEGER .1.3.6.1.4.1.232.167.2.3.5.2.1.6 |
internalSensorSetLowValue for low setpoint of sensor,
also used as alarm delayrw INTEGER .1.3.6.1.4.1.232.167.2.3.5.2.1.7 |
internalSensorSetWarnValue for warning setpoint of sensor,
also used as fan thresholdrw INTEGER .1.3.6.1.4.1.232.167.2.3.5.2.1.8 |
cpqWcrmStatusInternalOutputs OBJECT IDENTIFIER .1.3.6.1.4.1.232.167.2.3.6 |
cpqWcrmInternalNumberOfOutputsNumber of outputs available on internal sensorro INTEGER .1.3.6.1.4.1.232.167.2.3.6.1 |
cpqWcrmInternalOutputTableHeadline of output table SEQUENCE OF CpqWcrmInternalOutputEntry .1.3.6.1.4.1.232.167.2.3.6.2 |
cpqWcrmInternalOutputEntryEntries of output table CpqWcrmInternalOutputEntry .1.3.6.1.4.1.232.167.2.3.6.2.1 |
internalOutputIndexIndex for the list of output entries. Its value ranges
between 1 and the value of cpqWcrmInternalNumberOfOutputs.ro INTEGER .1.3.6.1.4.1.232.167.2.3.6.2.1.1 |
internalOutputTypeType of output which is connected to internal sensor to output[internalOutputIndex]
1: no output connected
2: output failure
3: value overflow
4: output type 6, universal relay output
5: output type 8, power outputro Enumeration .1.3.6.1.4.1.232.167.2.3.6.2.1.2 |
internalOutputTextDescriptional text for each output (entry in the table)rw DisplayString .1.3.6.1.4.1.232.167.2.3.6.2.1.3 |
internalOutputStatusActual status of the outputrw Enumeration .1.3.6.1.4.1.232.167.2.3.6.2.1.4 |
internalOutputValueValue for outputrw INTEGER .1.3.6.1.4.1.232.167.2.3.6.2.1.5 |
internalOutputSetCommand for outputrw Enumeration .1.3.6.1.4.1.232.167.2.3.6.2.1.6 |
internalOutputConfigConfiguration for output
1: disable remote control (e.g. keypad)
2: enable remote controlrw Enumeration .1.3.6.1.4.1.232.167.2.3.6.2.1.7 |
internalOutputDelayUnsigned Value for delay,
after this time the output will fall into the previous staterw INTEGER .1.3.6.1.4.1.232.167.2.3.6.2.1.8 |
internalOutputTimeoutActionState for output if timeout (RS422) occursrw Enumeration .1.3.6.1.4.1.232.167.2.3.6.2.1.9 |
cpqWcrmStatusInternalMsg OBJECT IDENTIFIER .1.3.6.1.4.1.232.167.2.3.7 |
cpqWcrmInternalNumberOfMsgsNumber of messages that can be created with internal sensorro INTEGER .1.3.6.1.4.1.232.167.2.3.7.1 |
cpqWcrmInternalMsgTableHeadline of message table SEQUENCE OF CpqWcrmInternalMsgEntry .1.3.6.1.4.1.232.167.2.3.7.2 |
cpqWcrmInternalMsgEntryEntries of message table CpqWcrmInternalMsgEntry .1.3.6.1.4.1.232.167.2.3.7.2.1 |
internalMsgIndexIndex for the list of message entries. Its value ranges
between 1 and the value of cpqWcrmInternalNumberOfMsgs.ro INTEGER .1.3.6.1.4.1.232.167.2.3.7.2.1.1 |
internalMsgTextDescriptional text for each message (entry in the table)rw DisplayString .1.3.6.1.4.1.232.167.2.3.7.2.1.2 |
internalMsgStatusActual message status
1: not available
2: configuration has changed (sensor new, changed, lost)
3: error
4: OK
5: alarm, e.g. smoke, vibration...
6: warning of analog value, value reached warning threshold
7: analog value too low, value reached low threshold
8: analog value too high, value reached high threshold
9: output is set to ON
10: output is set to OFFro Enumeration .1.3.6.1.4.1.232.167.2.3.7.2.1.3 |
internalMsgRelaySetup of Alarm relay for this message/alarm
1: no switching of alarm relay
2: switching of alarm relayrw Enumeration .1.3.6.1.4.1.232.167.2.3.7.2.1.4 |
internalMsgBeeperSetup of Alarm beeper for this alarm
1: no audible alarm
2: audible alarmrw Enumeration .1.3.6.1.4.1.232.167.2.3.7.2.1.5 |
internalMsgTrap1Trap receiver 1 activatedrw Enumeration .1.3.6.1.4.1.232.167.2.3.7.2.1.6 |
internalMsgTrap2Trap receiver 2 activatedrw Enumeration .1.3.6.1.4.1.232.167.2.3.7.2.1.7 |
internalMsgTrap3Trap receiver 3 activatedrw Enumeration .1.3.6.1.4.1.232.167.2.3.7.2.1.8 |
internalMsgTrap4Trap receiver 4 and Event Logging activatedrw Enumeration .1.3.6.1.4.1.232.167.2.3.7.2.1.9 |
internalMsgResetReset of this alarm
1: auto
2: manual, alarm needs confirmation, e. g. with 'C' keyrw Enumeration .1.3.6.1.4.1.232.167.2.3.7.2.1.10 |
cpqWcrmStatusSensorWaterCoolUnit OBJECT IDENTIFIER .1.3.6.1.4.1.232.167.2.4 |
cpqWcrmWaterCoolUnitTypeOfDeviceType of sensor unit connected to port 2ro Enumeration .1.3.6.1.4.1.232.167.2.4.1 |
cpqWcrmWaterCoolUnitTextDescriptional text for sensor unit connected to port 2rw DisplayString .1.3.6.1.4.1.232.167.2.4.2 |
cpqWcrmWaterCoolUnitSerialSerialnumber of sensor unit connected to port 2ro INTEGER .1.3.6.1.4.1.232.167.2.4.3 |
cpqWcrmWaterCoolUnitStatusGeneral Status sensor unit connected to port 2
(1) OK
(2) error
(3) configuration of sensor unit has changed, confirmation required
(4) reset from sensor unit to confirm configuration changes
(5) timeout of sensor unit, confirmation required
(6) sensor unit detected, needs to be confirmed
(8) supply voltage is too lowro Enumeration .1.3.6.1.4.1.232.167.2.4.4 |
cpqWcrmStatusWaterCoolUnitSensors OBJECT IDENTIFIER .1.3.6.1.4.1.232.167.2.4.5 |
cpqWcrmWaterCoolUnitNumberOfSensorsNumber of sensors connected to water cool unitro INTEGER .1.3.6.1.4.1.232.167.2.4.5.1 |
cpqWcrmWaterCoolUnitSensorTableHeadline of sensor table SEQUENCE OF CpqWcrmWaterCoolUnitSensorEntry .1.3.6.1.4.1.232.167.2.4.5.2 |
cpqWcrmWaterCoolUnitSensorEntryEntries of sensor table CpqWcrmWaterCoolUnitSensorEntry .1.3.6.1.4.1.232.167.2.4.5.2.1 |
waterCoolUnitSensorIndexIndex for the list of value entries. Its value ranges
between 1 and the value of cpqWcrmWaterCoolUnitNumberOfSensors.ro INTEGER .1.3.6.1.4.1.232.167.2.4.5.2.1.1 |
waterCoolUnitSensorTypeType of sensor which is connected to internal sensor to sensor[internalSensorIndex]
1: no sensor connected
2: sensor failure
3: value overflow
4: average temperature of air inlet to rack, average or max/min from each HEX
5: average temperature of air outlet from rack, average or max/min from each HEX
6: heatflow sensor
7: alarm:
Bit 0: Leakage
Bit 1: IIC Failure
8: warning:
Bit 0..2: Fan Tach 1..3
Bit 3,4: Temp. sensor HEX1 In,Out
Bit 5,6: Temp. sensor HEX2 In,Out
Bit 7,8: Temp. sensor HEX3 In,Out
Bit 9: Air temp. sensor
Bit 10..12: IIC failure, HEX1..3
Bit 13: Waterflow low
Bit 14,15: Watertemp. In,Out
Bit 16: Waterflow sensor fail.
Bit 17: Magnetic valve fail.
Bit 18: Leakdetector fail.
Bit 19: Uneven heat load
Bit 20: Condensation Pump Cycles > Max
Bit 21: Condensation Pump Running Time > Max
9: rpm speed of Fan1
10: rpm speed of Fan2
11: rpm speed of Fan3
12: fanSpeed setpoint, calculated from average temperatures
13: temperature air inlet to rack, HEX 1
14: temperature air outlet from rack, HEX 1
15: temperature air inlet to rack, HEX 1
16: temperature air outlet from rack, HEX 1
17: temperature air inlet to rack, HEX 1
18: temperature air outlet from rack, HEX 1
19: water temperature In
20: water temperature Out
21: water Flow
22: water valve status: MCS:0: Valve opened, 1: valve closed; MCSS: valve setpoint (%)
23: status: Bit 0..Bit 2: fan module 1..3 available
Bit 3: water module available
24: condensation pump number of seconds on counter (last operating time)
25: condensation pump on/off cycle counter
26: rpm speed of Fan4
27: rpm speed of Fan5
28: rpm speed of Fan6
29: status of transfer switch, 1=AC1, 2=AC2, 3=AC1 and AC2
30: water valve actual value (%)ro Enumeration .1.3.6.1.4.1.232.167.2.4.5.2.1.2 |
waterCoolUnitSensorTextDescriptional text for each sensor (entry in the table)rw DisplayString .1.3.6.1.4.1.232.167.2.4.5.2.1.3 |
waterCoolUnitSensorStatusActual status of the sensorro Enumeration .1.3.6.1.4.1.232.167.2.4.5.2.1.4 |
waterCoolUnitSensorValueValue of sensor added to traps, msg index also added (waterCoolUnitMsgIndex)
If msg index = 1, 5 or 6
This value represents the actual Server Intake Temperature.
If msg index = 2:
This value represents the bit coded warning condition
Bit 0: Top Fan Module Failed
Bit 1: Middle Fan Module Failed
Bit 2: Bottom Fan Module Failed
Bit 3: Top HEX Intake Air Temperature Sensor to Server Failed
Bit 4: Top HEX Exhaust Air Temperature Sensor from Server Failed
Bit 5: Middle HEX Intake Air Temperature Sensor to Server Failed
Bit 6: Middle HEX Exhaust Air Temperature Sensor from Server Failed
Bit 7: Bottom HEX Intake Air Temperature Sensor to Server Failed
Bit 8: Bottom HEX Exhaust Air Temperature Sensor from Server Failed
Bit 9: Air Temperature Sensor Failed
Bit 10: Top Fan not installed
Bit 11: Middle Fan not installed
Bit 12: Bottom Fan not installed
Bit 13: Waterflow low
Bit 14: Water Unit Temperature Input Out of Range
Bit 15: Water Unit Temperature Output Out of Range
Bit 16: Waterflow Sensor Value Out of Range
Bit 17: Water Valve Failed
Bit 18: Leakdetector Failed
Bit 19: Heat Load Warning
Bit 20: The Condensation Pump has exceeded the max. number of cycles
Bit 21: The Condensation Pump has exceeded the max. Running Time
If msg index = 3:
This value represents the bit coded alarm condition
Bit 0: Leakage Detected
Bit 1: Comm. Failure IICro INTEGER .1.3.6.1.4.1.232.167.2.4.5.2.1.5 |
waterCoolUnitSensorSetHighValue for high setpoint of sensorrw INTEGER .1.3.6.1.4.1.232.167.2.4.5.2.1.6 |
waterCoolUnitSensorSetLowValue for low setpoint of sensor,
also used as alarm delayrw INTEGER .1.3.6.1.4.1.232.167.2.4.5.2.1.7 |
waterCoolUnitSensorSetWarnValue for warning setpoint of sensor,
also used as fan thresholdrw INTEGER .1.3.6.1.4.1.232.167.2.4.5.2.1.8 |
cpqWcrmStatusWaterCoolUnitOutputs OBJECT IDENTIFIER .1.3.6.1.4.1.232.167.2.4.6 |
cpqWcrmWaterCoolUnitNumberOfOutputsNumber of outputs available on sensor water cool unitro INTEGER .1.3.6.1.4.1.232.167.2.4.6.1 |
cpqWcrmWaterCoolUnitOutputTableHeadline of output table SEQUENCE OF CpqWcrmWaterCoolUnitOutputEntry .1.3.6.1.4.1.232.167.2.4.6.2 |
cpqWcrmWaterCoolUnitOutputEntryEntries of output table CpqWcrmWaterCoolUnitOutputEntry .1.3.6.1.4.1.232.167.2.4.6.2.1 |
waterCoolUnitOutputIndexIndex for the list of output entries. Its value ranges
between 1 and the value of cpqWcrmWaterCoolUnitNumberOfOutputs.ro INTEGER .1.3.6.1.4.1.232.167.2.4.6.2.1.1 |
waterCoolUnitOutputTypeType of output which is connected to water cool unit to output[waterCoolUnitOutputIndex]
1: no output connected
2: output failure
3: value overflow
4: water valve setpoint
5: water valve hysteresis
6: command for manual control
7: Flow Meter Model, 0=SIKA, 1=Chemline
8: minimum fan speed
9: min delta T, used for fan control
10: max delta T, used for fan control
11: specific heat capacity
12: setpoint heatload warning
13: setpoint Water Flow Loss Emergency Door Opening
14: setpoint High Temperature Emergency Door Opening
15: setpoint Condensation Pump Cycles (Warning)
16: setpoint Condensation Pump Running Time (Warning)
17: command for door opening, 0=lock door, 1=unlock door
18: KP parameter for PID controller
19: KI parameter for PID controller
20: KD parameter for PID controller
21: sampling time PID controllerro Enumeration .1.3.6.1.4.1.232.167.2.4.6.2.1.2 |
waterCoolUnitOutputTextDescriptional text for each output (entry in the table)rw DisplayString .1.3.6.1.4.1.232.167.2.4.6.2.1.3 |
waterCoolUnitOutputStatusActual status of the outputrw Enumeration .1.3.6.1.4.1.232.167.2.4.6.2.1.4 |
waterCoolUnitOutputValueSigned value for outputrw INTEGER .1.3.6.1.4.1.232.167.2.4.6.2.1.5 |
waterCoolUnitOutputSetCommand for outputrw Enumeration .1.3.6.1.4.1.232.167.2.4.6.2.1.6 |
waterCoolUnitOutputConfigConfiguration for output
1: disable remote control (e.g. keypad)
2: enable remote controlrw Enumeration .1.3.6.1.4.1.232.167.2.4.6.2.1.7 |
waterCoolUnitOutputDelayUnsigned Value for delay,
after this time the output will fall into the previous staterw INTEGER .1.3.6.1.4.1.232.167.2.4.6.2.1.8 |
waterCoolUnitOutputTimeoutActionState for output if timeout (RS422) occursrw Enumeration .1.3.6.1.4.1.232.167.2.4.6.2.1.9 |
cpqWcrmStatusWaterCoolUnitMsg OBJECT IDENTIFIER .1.3.6.1.4.1.232.167.2.4.7 |
cpqWcrmWaterCoolUnitNumberOfMsgsNumber of alarms that can be created with water cool unitro INTEGER .1.3.6.1.4.1.232.167.2.4.7.1 |
cpqWcrmWaterCoolUnitMsgTableHeadline of message table SEQUENCE OF CpqWcrmWaterCoolUnitMsgEntry .1.3.6.1.4.1.232.167.2.4.7.2 |
cpqWcrmWaterCoolUnitMsgEntryEntries of message table CpqWcrmWaterCoolUnitMsgEntry .1.3.6.1.4.1.232.167.2.4.7.2.1 |
waterCoolUnitMsgIndexIndex for the list of alarm entries. Its value ranges
between 1 and the value of cpqWcrmWaterCoolUnitNumberOfMsgs.ro INTEGER .1.3.6.1.4.1.232.167.2.4.7.2.1.1 |
waterCoolUnitMsgTextDescriptional text for each message (entry in the table)rw DisplayString .1.3.6.1.4.1.232.167.2.4.7.2.1.2 |
waterCoolUnitMsgStatusActual message status
4: OK
5: alarm
6: warning
7: analog value too low, value reached low threshold
8: analog value too high, value reached high thresholdro Enumeration .1.3.6.1.4.1.232.167.2.4.7.2.1.3 |
waterCoolUnitMsgRelaySetup of Alarm relay for this alarm
2: no switching of alarm relay
1: switching of alarm relayrw Enumeration .1.3.6.1.4.1.232.167.2.4.7.2.1.4 |
waterCoolUnitMsgBeeperSetup of Alarm beeper for this alarm
2: no audible alarm
1: audible alarmrw Enumeration .1.3.6.1.4.1.232.167.2.4.7.2.1.5 |
waterCoolUnitMsgTrap1Trap receiver 1 activatedrw Enumeration .1.3.6.1.4.1.232.167.2.4.7.2.1.6 |
waterCoolUnitMsgTrap2Trap receiver 2 activatedrw Enumeration .1.3.6.1.4.1.232.167.2.4.7.2.1.7 |
waterCoolUnitMsgTrap3Trap receiver 3 activatedrw Enumeration .1.3.6.1.4.1.232.167.2.4.7.2.1.8 |
waterCoolUnitMsgTrap4Trap receiver 4 and Event Logging activatedrw Enumeration .1.3.6.1.4.1.232.167.2.4.7.2.1.9 |
waterCoolUnitMsgResetReset of this alarm
1: auto
2: manual, alarm needs confirmation, e. g. with 'C' keyrw Enumeration .1.3.6.1.4.1.232.167.2.4.7.2.1.10 |
cpqWcrmURLURL of the management interface in the format http[s]://ipaddr[:port#][/page]ro DisplayString .1.3.6.1.4.1.232.167.2.7 |
cpqWcrmSetup OBJECT IDENTIFIER .1.3.6.1.4.1.232.167.3 |
cpqWcrmSetupGeneral OBJECT IDENTIFIER .1.3.6.1.4.1.232.167.3.1 |
cpqWcrmSetTempUnitUnit of all temperature values and setpoints, Celsius or Fahrenheitrw Enumeration .1.3.6.1.4.1.232.167.3.1.1 |
cpqWcrmSetBeeperAudible alarm in Environmental Controller unit:
(2): beeper is on
(1): beeper is off (general)rw Enumeration .1.3.6.1.4.1.232.167.3.1.2 |
cpqWcrmResetRelayEnable or disable acknowledging currently active alarm relay
(with 'C' on Environmental Controller).rw Enumeration .1.3.6.1.4.1.232.167.3.1.3 |
cpqWcrmLogicRelayLogic of alarm relay:
(1) Relay will pick up in case of an alarm
(2) Relay will release in case of an alarm
(3) Relay off (general)rw Enumeration .1.3.6.1.4.1.232.167.3.1.4 |
cpqWcrmWebAccessWeb access via HTTP:
(1) view only
(2) full Access, read and set
(3) Web disabled (general)rw Enumeration .1.3.6.1.4.1.232.167.3.1.5 |
cpqWcrmSetupDateactual Date in format DD.MM.YYYYrw DisplayString .1.3.6.1.4.1.232.167.3.1.6 |
cpqWcrmSetupTimeactual Time in format HH:MM:SS, HH (0-23), MM (0-59), SS (0-59)rw DisplayString .1.3.6.1.4.1.232.167.3.1.7 |
cpqWcrmTimerTable1 OBJECT IDENTIFIER .1.3.6.1.4.1.232.167.3.1.8 |
cpqWcrmTimerNumberNumber of value-table entries=number of outlets available on this unitro INTEGER .1.3.6.1.4.1.232.167.3.1.8.1 |
cpqWcrmTimerTableHeadline of status-table SEQUENCE OF CpqWcrmTimerEntry .1.3.6.1.4.1.232.167.3.1.8.2 |
cpqWcrmTimerEntryEntries of timer-table CpqWcrmTimerEntry .1.3.6.1.4.1.232.167.3.1.8.2.1 |
cpqWcrmTimerIndexIndex for the list of timer entries. Its value ranges
between 1 and the value of cpqWcrmTimerNumber.ro INTEGER .1.3.6.1.4.1.232.167.3.1.8.2.1.1 |
cpqWcrmTimerStatusActual status of the timerro Enumeration .1.3.6.1.4.1.232.167.3.1.8.2.1.2 |
cpqWcrmTimerDayOfWeekSelection of day of week for timer to switchrw Enumeration .1.3.6.1.4.1.232.167.3.1.8.2.1.3 |
cpqWcrmTimeOnTime to switch on current function,
Format: HH:MMrw DisplayString .1.3.6.1.4.1.232.167.3.1.8.2.1.4 |
cpqWcrmTimeOffTime to switch off current function,
Format: HH:MMrw DisplayString .1.3.6.1.4.1.232.167.3.1.8.2.1.5 |
cpqWcrmTimeControlControl via RTCrw Enumeration .1.3.6.1.4.1.232.167.3.1.8.2.1.6 |
cpqWcrmTimerFunctionFunction which is controlled via timer
1-4: sending Traps to this Trap receiver will be disabled
5 - 8: scheduled alarm offrw Enumeration .1.3.6.1.4.1.232.167.3.1.8.2.1.7 |
cpqWcrmSetFlowUnitUnit of Water Flow, Liter/min or Gallon/minrw Enumeration .1.3.6.1.4.1.232.167.3.1.9 |
cpqWcrmTrapControl OBJECT IDENTIFIER .1.3.6.1.4.1.232.167.4 |
cpqWcrmTraps OBJECT IDENTIFIER .1.3.6.1.4.1.232.167.4.7 |
cpqWcrmTraptableNumberNumber of trapTable entries. The number of trap-receiverro INTEGER .1.3.6.1.4.1.232.167.4.7.1 |
cpqWcrmTrapTableTableA list of trap-receiver entries SEQUENCE OF CpqWcrmTrapTableEntry .1.3.6.1.4.1.232.167.4.7.2 |
cpqWcrmTrapTableEntryEntries of trapTable CpqWcrmTrapTableEntry .1.3.6.1.4.1.232.167.4.7.2.1 |
trapIndexIndex for the trap-receiver-table. Its value ranges between
1 and the value of traptableNumberro INTEGER .1.3.6.1.4.1.232.167.4.7.2.1.1 |
trapStatusEnable or disable trap receiverrw Enumeration .1.3.6.1.4.1.232.167.4.7.2.1.2 |
trapIPaddressIP-address of trap-receiverrw DisplayString .1.3.6.1.4.1.232.167.4.7.2.1.3 |
cpqWcrmControl OBJECT IDENTIFIER .1.3.6.1.4.1.232.167.5 |
cpqWcrmResetUnitCommand to reset (acknowledge) alarms of Environmental Controller unit.
Setting to 'reset' (2) will have same result as pressing 'C' on Units.
Variable is automatically set back to 'noReset' (1).rw Enumeration .1.3.6.1.4.1.232.167.5.1 |