CASCADE-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for CASCADE-MIB.
536
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
536 total| Object Name |
|---|
cascade OBJECT IDENTIFIER .1.3.6.1.4.1.277 |
RFC1213-MIB Unknown .1.3.6.1.4.1.277 |
cascfr OBJECT IDENTIFIER .1.3.6.1.4.1.277.1 |
net OBJECT IDENTIFIER .1.3.6.1.4.1.277.1.1 |
netMaskThe IP subnet mask for the network. The default is
255.255.255.0 (class C) which allows 254 nodes.rw IpAddress .1.3.6.1.4.1.277.1.1.1 |
netNumberThe IP network number for the network.rw IpAddress .1.3.6.1.4.1.277.1.1.2 |
netDlciAddrSigThis variable states the DLCI addressing significance.rw Enumeration .1.3.6.1.4.1.277.1.1.3 |
netMaxSegsizeThis variable states the maximum sgement size for the network.rw INTEGER .1.3.6.1.4.1.277.1.1.4 |
netSmdsAreaMaskStartThis variable states the starting digit number for defining
the start of the Area Mask for SMDS Addresses.rw INTEGER .1.3.6.1.4.1.277.1.1.8 |
netSmdsAreaMaskDigitsThis variable states the number of digits used for defining
the Area Mask for SMDS Addresses.rw INTEGER .1.3.6.1.4.1.277.1.1.9 |
ase OBJECT IDENTIFIER .1.3.6.1.4.1.277.1.2 |
aseTableA list of ASE entries. SEQUENCE OF AseEntry .1.3.6.1.4.1.277.1.2.1 |
aseEntryAn ASE entry contains an external NMS path accessible from
the node. AseEntry .1.3.6.1.4.1.277.1.2.1.1 |
aseAddrIP Address for an external NMS.ro IpAddress .1.3.6.1.4.1.277.1.2.1.1.1 |
aseMaskIP Address mask for an external NMS. The default value
is 255.255.255.255.ro IpAddress .1.3.6.1.4.1.277.1.2.1.1.2 |
aseDefaultGwAddrDefault Gateway IP Address for reaching the external
NMS. This field is not applicable to NMSs which are
reachable via SLIP or on the same Ethernet.rw IpAddress .1.3.6.1.4.1.277.1.2.1.1.3 |
aseMetricTypeType of metric (1 or 2) for each external NMS.
The default is 1. (This field is not applicable to SLIP-
based hosts.)ro INTEGER .1.3.6.1.4.1.277.1.2.1.1.4 |
aseAdminStatusThe desired state of the entry.rw Enumeration .1.3.6.1.4.1.277.1.2.1.1.5 |
aseIfIndexThe interface value of the corresponding MIB-II ifEntry.rw Index .1.3.6.1.4.1.277.1.2.1.1.6 |
aseDlciThe management dlci through which the NMS communicates
to the switch.rw INTEGER .1.3.6.1.4.1.277.1.2.1.1.7 |
node OBJECT IDENTIFIER .1.3.6.1.4.1.277.1.3 |
nodeIpAddrThe inband IP address of the node in the Cascade internal
trunk IP network.rw IpAddress .1.3.6.1.4.1.277.1.3.1 |
nodeLanIpAddrThe inband (Ethernet) IP address of the node for a NMS
to access the node and the internal trunk IP network.rw IpAddress .1.3.6.1.4.1.277.1.3.2 |
nodeNMSTableA list of NMS entries. SEQUENCE OF NodeNMSEntry .1.3.6.1.4.1.277.1.3.3 |
nodeNMSEntryA NMS entry contains an IP address of a NMS which has
extended privilages. NodeNMSEntry .1.3.6.1.4.1.277.1.3.3.1 |
nodeNMSIndexThe IP address entry of a primary Network Management Station.ro Index .1.3.6.1.4.1.277.1.3.3.1.1 |
nodeNMSIpAddrThe IP address of the primary Network Management Station.
It is to this address that Traps and TFTP requests
will be directed.rw IpAddress .1.3.6.1.4.1.277.1.3.3.1.2 |
nodeStateThe state of the switch. The switch needs to await the
state to be set to active before being fully operational
after cold boot, when the NMS is reachable.rw Enumeration .1.3.6.1.4.1.277.1.3.4 |
nodePollStatusThe consolidated node status in response to keep-alive polls.
It is an octet string of a proprietary formatro OCTET STRING .1.3.6.1.4.1.277.1.3.5 |
nodeModelThe part number of the node.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.3.6 |
nodeSerialThe serial number (i.e., Ethernet Addr) of the switch.ro OCTET STRING .1.3.6.1.4.1.277.1.3.7 |
nodeSwRevThe software revision number (major.minor).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.3.8 |
nodeHwRevThe hardware revision number (major.minor).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.3.9 |
nodeEpromRevThe EPROM firmware revision number (major.minor).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.3.10 |
nodeCpuUtilThe CPU utilization percentage for packet processing.ro Gauge .1.3.6.1.4.1.277.1.3.11 |
nodePsAStatusThe status of the power supply A. For a detailed explanation
for the power supply being either in the down or marginal
state, refer to the nodePsADiagCode object.ro Enumeration .1.3.6.1.4.1.277.1.3.12 |
nodePsBStatusThe status of the power supply B. For a detailed explanation
for the power supply being either in the down or marginal
state, refer to the nodePsBDiagCode object.ro Enumeration .1.3.6.1.4.1.277.1.3.13 |
nodeFanTableA list of fan entries. SEQUENCE OF NodeFanEntry .1.3.6.1.4.1.277.1.3.14 |
nodeFanEntryA Fan entry contains the status of a fan. NodeFanEntry .1.3.6.1.4.1.277.1.3.14.1 |
nodeFanIndexA unique value for each fan.ro INTEGER .1.3.6.1.4.1.277.1.3.14.1.1 |
nodeFanStatusThe status of the fan.ro Enumeration .1.3.6.1.4.1.277.1.3.14.1.2 |
nodeFanSpeedThe speed in Revolutions Per. Minute (RPM) of the fan.ro Gauge .1.3.6.1.4.1.277.1.3.14.1.3 |
nodeMemoryUtilThe percentage of system memory utilization on this intelligent card.ro Gauge .1.3.6.1.4.1.277.1.3.15 |
nodeMemoryUsageThe system memory utilization, in terms of free bytes, for
this intelligent card.ro Gauge .1.3.6.1.4.1.277.1.3.16 |
nodeMaxFramesizeThe maximum frame size supported by the node.
The default is 4096.ro INTEGER .1.3.6.1.4.1.277.1.3.17 |
nodeQOSPollTimerThe timer (seconds) for generating QOS polling packets.rw INTEGER .1.3.6.1.4.1.277.1.3.18 |
nodeActivePvcsThe number of currently active PVCs on the node.ro Counter .1.3.6.1.4.1.277.1.3.19 |
nodeInactivePvcsThe number of currently inactive PVCs on the node.ro Counter .1.3.6.1.4.1.277.1.3.20 |
nodePendingPvcsThe number of currently call pending PVCs on the node.ro Counter .1.3.6.1.4.1.277.1.3.21 |
nodeInOctetsThe total number of octets received on the node, including
framing bytes.ro Counter .1.3.6.1.4.1.277.1.3.22 |
nodeInPktsThe total number of packets received on the node.ro Counter .1.3.6.1.4.1.277.1.3.23 |
nodeOutOctetsThe total number of octets transmitted out of the node,
including framing bytes.ro Counter .1.3.6.1.4.1.277.1.3.24 |
nodeOutPktsThe total number of packets requested to be transmitted out
of the node, including those that were discarded or not sent.ro Counter .1.3.6.1.4.1.277.1.3.25 |
nodeSwFilenameName of the file to be downloaded.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.3.26 |
nodeRebootAfterLoadInstructs the device to either automatically reboot after
the successful scheduled download or not.rw Enumeration .1.3.6.1.4.1.277.1.3.27 |
nodeSwToLoadInstructs the device to initiate a software download
(via tftp) request to the master management station after
the specified time ticks have elapsed.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.3.28 |
nodeSwLoadStateThe state of the software download request. A download
which is in either the PENDING, ACTIVE or FAILED state
can be terminated by setting this object to INACTIVE.rw Enumeration .1.3.6.1.4.1.277.1.3.29 |
nodePrFilenameName of the PRAM image file to be downloaded.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.3.30 |
nodePrToLoadInstructs the device to initiate a PRAM image file download
(via tftp) request to the master management station after
the specified time ticks have elapsed.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.3.31 |
nodePrLoadStateThe state of the PRAM download request. A download
which is in either the PENDING, ACTIVE or FAILED state
can be terminated by setting this object to INACTIVE.rw Enumeration .1.3.6.1.4.1.277.1.3.32 |
nodeToWarmbootInstructs the switch to initiate a system warm boot after
the specified time ticks have elapsed. A value of 0 indicates
cancellation of the previously scheduled re-boot request.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.3.33 |
nodeToColdbootInstructs the switch to initiate a system cold boot after
the specified time ticks have elapsed. A value of 0 indicates
cancellation of the previously scheduled re-boot request.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.3.34 |
nodeToRedundantIf redundancy is configured, instructs the node acting as Backup
to disable the Active node and take over as the Active node.
The disabling is initiated after the specified time ticks have
elapsed. A value of 0 indicates cancellation of the previously
scheduled request.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.3.35 |
nodeInitiateBulkStatsInitiates a Bulk Statistics poll and via TFTP, transfer the data
to the specified IP address.rw IpAddress .1.3.6.1.4.1.277.1.3.36 |
nodeDiagNonFatalSourceSource who reported last non-fatal error.ro Enumeration .1.3.6.1.4.1.277.1.3.37 |
nodeDiagNonFatalTimeTime the last non-fatal error was reported.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.3.38 |
nodeDiagNonFatalErrMajorMajor error code of last non-fatal error.ro INTEGER .1.3.6.1.4.1.277.1.3.39 |
nodeDiagNonFatalErrMinorMinor error code of last non-fatal error.ro INTEGER .1.3.6.1.4.1.277.1.3.40 |
nodeDiagNonFatalStrAscii string describing last non-fatal error.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.3.41 |
nodeDiagFatalSourceSource who reported last fatal error.ro Enumeration .1.3.6.1.4.1.277.1.3.42 |
nodeDiagFatalTimeTime the last fatal error was reported.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.3.43 |
nodeDiagFatalErrMajorMajor error code of last fatal error.ro INTEGER .1.3.6.1.4.1.277.1.3.44 |
nodeDiagFatalErrMinorMinor error code of last fatal error.ro INTEGER .1.3.6.1.4.1.277.1.3.45 |
nodeDiagFatalStrAscii string describing last fatal error.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.3.46 |
nodeDiagFatalRebootsNumber of times the switch has re-booted since last
fatal error was reported.ro Counter .1.3.6.1.4.1.277.1.3.47 |
nodeDiagFatalAddressAddress switch was executing when it encountered fatal error.ro INTEGER .1.3.6.1.4.1.277.1.3.48 |
nodeDiagBackgroundPassesNumber of passes made by the background diagnostics.ro Counter .1.3.6.1.4.1.277.1.3.49 |
nodeDiagBackgroundFailuresNumber of failures discovered by background diagnostics.ro Counter .1.3.6.1.4.1.277.1.3.50 |
nodeDiagBackgroundSuccessesNumber of successful passes by background diagnostics.ro Counter .1.3.6.1.4.1.277.1.3.51 |
nodeDiagLEDResetChange the node state from marginal to active. Change the
LED from yellow to green.rw Enumeration .1.3.6.1.4.1.277.1.3.52 |
nodeDiagPowerExtensiveShould power on diagnostics do slower, extensive testing,
or fast testing?rw Enumeration .1.3.6.1.4.1.277.1.3.53 |
nodePortPollThe consolidated port status in response to keep-alive polls.ro OCTET STRING .1.3.6.1.4.1.277.1.3.54 |
nodeMaxTelnetConsoleThe number of concurrent telnet consoles allowed. The default
is 2. The maximum is 5. Set it 0 to disable telnet access.rw INTEGER .1.3.6.1.4.1.277.1.3.55 |
nodeConsoleTimeoutIdle-logoff timer in minutes. The default is 5 minutes, and the
maximum can be set is 60 minutes. To disable idle-logout, set
this to 0.rw INTEGER .1.3.6.1.4.1.277.1.3.56 |
nodeConsoleTableA list of active consoles on the node, logged in through telnet
or serial port. SEQUENCE OF NodeConsoleEntry .1.3.6.1.4.1.277.1.3.57 |
nodeConsoleEntryInformation of a console. NodeConsoleEntry .1.3.6.1.4.1.277.1.3.57.1 |
nodeConsoleIndexA positive integer to identify a consolero INTEGER .1.3.6.1.4.1.277.1.3.57.1.1 |
nodeUserNameThe login user name up to 31 characters. There is no
validation of the name, i.e., any string is acceptable.ro OCTET STRING .1.3.6.1.4.1.277.1.3.57.1.2 |
nodeUserFromThe IP address from which the user logged in. 0.0.0.0 if the
user logged in through serial port.ro IpAddress .1.3.6.1.4.1.277.1.3.57.1.3 |
nodeConsoleAccessModeThe access mode of the console. By default, a user is in READ ONLY
mode.ro Enumeration .1.3.6.1.4.1.277.1.3.57.1.4 |
nodeConsoleUptimeHow long the console has been active.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.3.57.1.5 |
nodePsADiagCodeThe failure code of the power supply A. A non-zero value
indicates one or more failures. Refer to the hardware
manual for a description of the failure code.ro INTEGER .1.3.6.1.4.1.277.1.3.58 |
nodePsBDiagCodeThe failure code of the power supply B. A non-zero value
indicates one or more failures. Refer to the hardware
manual for a description of the failure code.ro INTEGER .1.3.6.1.4.1.277.1.3.59 |
nodeFrameMemoryUtilThe percentage of frame memory utilization on this intelligent card.ro Gauge .1.3.6.1.4.1.277.1.3.60 |
nodeFrameMemoryUsageThe frame memory utilization, in terms of free bytes, for
this intelligent card.ro Gauge .1.3.6.1.4.1.277.1.3.61 |
nodeCapabilityThe capability of this node.ro Enumeration .1.3.6.1.4.1.277.1.3.62 |
nodeSvcLastCallFailureA textual string describing the last call failure.ro OCTET STRING .1.3.6.1.4.1.277.1.3.63 |
nodeRerouteDelayThe number of seconds delay between each reroute batch event.rw INTEGER .1.3.6.1.4.1.277.1.3.64 |
nodeRerouteCountThe number of virtual circuits to request a reroute for duing
a single reroute batch event.rw INTEGER .1.3.6.1.4.1.277.1.3.65 |
nodeFileTransferRequestThis object is used to initiate file transfers to and from
the switch. A management station can initiate a file transfer
by settting this object of text string in the following
format:
operation filename time-to-wait target-host protocol
where
operation - [get | put],
filename - configuration.[card]
time-to-wait - a number in seconds
target-host - the IP address of target host
protocol - [tftp | ftp]
Multiple transfers can be specified by repeating above with
';' between each transfer specifier.
Examples:
o get configuration.10 5 152.148.10.100 tftp
will start a transfer of configuration information
on card 10 to host 152.148.10.100 in 5 seconds.
o put configuration.1 2 152.148.1.1 tftp ;
get configuration.1 15 152.148.1.1 tftp
will (1) transfer configuration.1 from 152.148.1.1
(2) transfer configuration.2 to 152.148.1.1
To cancel the transfer request, set this object to empty.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.3.66 |
nodeFileTransferStatusThe status of the file tarnsfer.ro Enumeration .1.3.6.1.4.1.277.1.3.67 |
nodeTimeThe current wall-clock time that is set on the switch in
Universal Coordinated Time (UCT). The value is the number
of seconds since 00:00:00 UCT January 1, 1970.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.3.68 |
nodeBillingAPAddressThe IP Address of the Adjunct Billing Processor that is
servicing this switch.rw IpAddress .1.3.6.1.4.1.277.1.3.69 |
nodeBillingAPUsernameThe Username of the account on the Adjunct Billing Processor
to which usage data will be transferred via FTP.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.3.70 |
nodeBillingAPPasswordThe Password corresponding to the account identified by
nodeBillingAPUsername. A NULL string is returned when read.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.3.71 |
nodeBillingSwAPCommsFailuresThe number of times that communication from the switch to the
Adjunct Billing Processor has failed during the current
aggregation period. A failure signifies failure of a file
transfer operation to the Adjunct Processor.rw Counter .1.3.6.1.4.1.277.1.3.72 |
nodeBillingTableA table of Billing System managable objects, indexed by
service. SEQUENCE OF NodeBillingEntry .1.3.6.1.4.1.277.1.3.73 |
nodeBillingEntryA nodeBillingEntry contains a set of statistics that
summarize the Billing System performance for a particular
service. NodeBillingEntry .1.3.6.1.4.1.277.1.3.73.1 |
nodeBillingServiceThe service being reported. This is the index into the table.
Additional table rows for Frame Relay and ATM may be provided
in the future.ro Enumeration .1.3.6.1.4.1.277.1.3.73.1.1 |
nodeBillingSwitch to enable and disable billing on the STDX.
When the value of nodeBilling is 'enabled', the value of a
logical port's lportBilling object will take precedence. When
the value of nodeBilling is 'disabled', it overrides all
logical ports' lportBilling objects and billing is disabled
across the entire switch.
The default value of this object is 'disabled'.rw Enumeration .1.3.6.1.4.1.277.1.3.73.1.2 |
nodeBillingAggrPeriodDefines the length of the Billing Aggregation Period in
seconds. The default value is 15 minutes. The minimum value
is 10 minutes.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.3.73.1.3 |
nodeBillingCurAggrPeriodStartThe start-time of the current aggregation period, given by
the number of seconds since 00:00:00 UCT January 1, 1970.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.3.73.1.4 |
nodeBillingCurAggrPeriodEndThe end-time of the current aggregation period, given by
the number of seconds since 00:00:00 UCT January 1, 1970.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.3.73.1.5 |
nodeBillingCollectionDefines how often the Data Aggregation process on the CP is
to poll the IOPs for usage data. The default value is 30
second. The range is unbounded, but practical use will
dictate a range from 30 seconds to 1 minute.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.3.73.1.6 |
nodeBillingDailyProcessingDefines whether the Billing System is to perform a set of
carrier-specific actions at the time given by
nodeBillingDPTime. This object can be used to schedule the
generation of statistics on a 24-hour basis, for example.rw Enumeration .1.3.6.1.4.1.277.1.3.73.1.7 |
nodeBillingDPTimeDefines the time (given by the number of seconds since
00:00:00 UCT) that the Billing System is to perform a set of
carrier-specific actions. This object can be used to schedule
the generation of statistics on a 24-hour basis, for example.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.3.73.1.8 |
nodeBillingUsageRecOvflWarningsCount of the number of usage record counter-value overflow
conditions that have occurred during the current aggregation
period. An overflow condition exists when an attempt was made
to update a usage record counter, but such an update would have
overflowed the counter. In this case, the usage record is
closed and a new one is opened, if there is sufficient space in
the service's aggregated usage data store.ro Counter .1.3.6.1.4.1.277.1.3.73.1.9 |
nodeBillingTotalUsageRecOvflWarningsCount of the number of usage record overflow conditions that
have occurred during the current day.ro Counter .1.3.6.1.4.1.277.1.3.73.1.10 |
nodeBillingBillableUsageEventsCount of the number of data units (e.g, SMDS L3 PDUs)
processed for billing treatment.ro Counter .1.3.6.1.4.1.277.1.3.73.1.11 |
nodeBillingNonBillableUsageEventsCount of the number of data units (e.g, SMDS L3 PDUs) not
considered for billing treatment.ro Counter .1.3.6.1.4.1.277.1.3.73.1.12 |
nodeBillingUsageRecCreatedCount of the number of usage records created during the
current aggregation period.ro Counter .1.3.6.1.4.1.277.1.3.73.1.13 |
nodeBillingTotalUsageRecCreatedCount of the total number of usage records created during
the current day.ro Counter .1.3.6.1.4.1.277.1.3.73.1.14 |
nodeBillingUsageRecCrFailuresTotal number of usage records that could not be created during
the current aggregation period. This counter is normally
incremented when the usage data file is at capacity and no
additional usage records can be added.ro Counter .1.3.6.1.4.1.277.1.3.73.1.15 |
nodeBillingTotalUsageRecCrFailuresTotal number of usage records that could not be created during
the current day.ro Counter .1.3.6.1.4.1.277.1.3.73.1.16 |
nodeBillingUsageRecSentTotal number of usage records that have been transferred to
the Adjunct Billing Processor during the current aggregation
period.ro Counter .1.3.6.1.4.1.277.1.3.73.1.17 |
nodeBillingTotalUsageRecSentTotal number of usage records that have been transferred to
the Adjunct Billing Processor during the current day.ro Counter .1.3.6.1.4.1.277.1.3.73.1.18 |
nodeBillingUsageDataStoreFullThe number of times the aggregated usage data store became
full during the current aggregation period.ro Counter .1.3.6.1.4.1.277.1.3.73.1.19 |
nodeBillingTotalUsageDataStoreFullTotal number of times the aggregated usage data store became
full during the current day.ro Counter .1.3.6.1.4.1.277.1.3.73.1.20 |
nodeBillingAdminActionThis object defines a set of administrative actions that
can be performed by the Billing System.
forceUpload - Forces the current aggregation period to end
and the service's aggregated usage data file to be uploaded
to the Adjunct Processor. A new aggregation period is
then started. This action can be requested when billing is
enabled or disabled for the service.
This object always returns invalid(1) when read.rw Enumeration .1.3.6.1.4.1.277.1.3.73.1.21 |
nodeRerouteAlgThe number of seconds delay between each reroute batch event.rw Enumeration .1.3.6.1.4.1.277.1.3.74 |
nodeOamAlarmDisabledIf disabled then don't generate oam alarms for circuits that are
down on this switch.rw Enumeration .1.3.6.1.4.1.277.1.3.76 |
nodeRefclocksrcTableA list of generators (sources) for the system reference
clock on the node. This reference clock is used by the clock
generation unit (CGU) to create the system clock. To this
reference clock the constant bit rate ATM interface cards
(CBR cards) are synchronized. SEQUENCE OF NodeRefclocksrcEntry .1.3.6.1.4.1.277.1.3.77 |
nodeRefclocksrcEntryInformation of a single system reference clock source. NodeRefclocksrcEntry .1.3.6.1.4.1.277.1.3.77.1 |
nodeRefclocksrcIndexA positive integer to identify an entry in the nodeRefclocksrcTable.rw INTEGER .1.3.6.1.4.1.277.1.3.77.1.1 |
nodeRefclocksrcPriorityThe priority of the system reference clock source.
A source with a nodeRefclocksrcPriority=n means that this source is
used before a source with a higher value of nodeRefclocksrcPriority
as long as this source is available.
The system choses one of the sources with the same lowest
available value of nodeRefclocksrcPriority.rw INTEGER .1.3.6.1.4.1.277.1.3.77.1.2 |
nodeRefclocksrcTypeThe type of the reference clock source. It is either an
external clock source connected to a ATM-IWU or DS3 card,
or the reference clock is recovered from the line interface.rw Enumeration .1.3.6.1.4.1.277.1.3.77.1.3 |
nodeRefclocksrcSlotIdThe card number of the reference clock source.
In case of an external clock interface this is the number of
the card as defined in cardLogicalSlotId.
In case of a clock recovered from the line interface it is
the number of the corresponding card as defined in
cardLogicalSlotId.rw INTEGER .1.3.6.1.4.1.277.1.3.77.1.4 |
nodeRefclocksrcPportIdThe interface number of the reference clock source.
In case of an external clock interface this is meaningless.
In case of a clock recovered from the line interface it is
the number of the corresponding pport as defined in pportId.rw INTEGER .1.3.6.1.4.1.277.1.3.77.1.5 |
nodeRefclockActiveSrcThe entry number of the active reference clock source in
nodeRefclocksrcTable. If zero, the CGU is in free-running mode or
holdover mode using the last PLL parameters.ro INTEGER .1.3.6.1.4.1.277.1.3.78 |
nodeRefclockActiveCGUSlotIdThe physical slot id of the current master CGU board.ro INTEGER .1.3.6.1.4.1.277.1.3.79 |
nodeRefclockActiveCGUModeThe clock mode of the current master CGU board.ro Enumeration .1.3.6.1.4.1.277.1.3.80 |
nodeInitiateImageBackupWhen set, copy all of the runtime application images
and configuration images to there corresponding backup
locations on the hard disk.rw Enumeration .1.3.6.1.4.1.277.1.3.81 |
nodeImageBackupStateProvides the current state of the images backup
operation.ro Enumeration .1.3.6.1.4.1.277.1.3.82 |
nodeInitiateImageRestoreWhen set, copy all of the runtime application images
and configuration images from their BACKUP locations on
the hard disk to there corresponding ACTIVE locations on
the hard disk. Once completed, reboot the entire node.rw Enumeration .1.3.6.1.4.1.277.1.3.83 |
nodeApplicationTableA list of Application Image Descriptions. SEQUENCE OF NodeApplicationEntry .1.3.6.1.4.1.277.1.3.84 |
nodeApplicationEntryAn Application Entry contains a description of the
application image, the version of the PRIMARY copy and
the version of the SECONDARY copy. NodeApplicationEntry .1.3.6.1.4.1.277.1.3.84.1 |
nodeApplicationIndexThe numeric index of application images.
1 - SP Runtime Application
2 - IOM Type A Runtime Application
3 - IOM Type B Runtime Application
4 - IOM Type C Runtime Application
5 - IOM Type D Runtime Applicationro Index .1.3.6.1.4.1.277.1.3.84.1.1 |
nodeApplicationDescriptionThe description of this Application Image.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.3.84.1.2 |
nodePrimaryVersionThe version of the PRIMARY Application Image.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.3.84.1.3 |
nodeSecondaryVersionThe version of the SECONDARY Application Image.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.3.84.1.4 |
nodePrimarySyncRefAdminStateThe requested primary clock synchronization reference
source.rw Enumeration .1.3.6.1.4.1.277.1.3.85 |
nodePrimarySyncRefOperationalStateThe actual primary clock synchronization reference source.ro Enumeration .1.3.6.1.4.1.277.1.3.86 |
nodeSecondarySyncRefAdminStateThe requested secondary clock synchronization reference
source.rw Enumeration .1.3.6.1.4.1.277.1.3.87 |
nodeSecondarySyncRefOperationalStateThe actual secondary clock synchronization reference
source.ro Enumeration .1.3.6.1.4.1.277.1.3.88 |
nodePrimaryPLLOperationalStateThe current state of the primary synchronization PLL.ro Enumeration .1.3.6.1.4.1.277.1.3.89 |
nodeSecondaryPLLOperationalStateThe current state of the secondary synchronization PLL.ro Enumeration .1.3.6.1.4.1.277.1.3.90 |
nodeExternalClockAOperationalStateThe current state of the External Clock A reference.ro Enumeration .1.3.6.1.4.1.277.1.3.91 |
nodeExternalClockBOperationalStateThe current state of the External Clock B reference.ro Enumeration .1.3.6.1.4.1.277.1.3.92 |
nodePortClockAOperationalStateThe current state of the Port Clock A reference.ro Enumeration .1.3.6.1.4.1.277.1.3.93 |
nodePortClockBOperationalStateThe current state of the Port Clock B reference.ro Enumeration .1.3.6.1.4.1.277.1.3.94 |
nodeExternalTimingSourceThe reference for the external timing output.rw Enumeration .1.3.6.1.4.1.277.1.3.95 |
nodeSyncAutoRestoreThe configuration of the Synchronization Reference Auto
Restoration function.rw Enumeration .1.3.6.1.4.1.277.1.3.96 |
nodeExternalClockInterfaceTypeThe interface type of the External Clock references.ro Enumeration .1.3.6.1.4.1.277.1.3.97 |
pport OBJECT IDENTIFIER .1.3.6.1.4.1.277.1.4 |
pportNumberThe number of physical ports (regardless of their current
state) present at this node.ro INTEGER .1.3.6.1.4.1.277.1.4.1 |
pportTableA list of physical port entries. The number of entries is
given by the value of pportNumber. SEQUENCE OF PportEntry .1.3.6.1.4.1.277.1.4.2 |
pportEntryThe physical port entry contains objects relevant to a
physical port. PportEntry .1.3.6.1.4.1.277.1.4.2.1 |
pportSlotIdThe slot number of the corresponding physical port.ro INTEGER .1.3.6.1.4.1.277.1.4.2.1.1 |
pportIdThe port number of the corresponding physical port
on the board.ro INTEGER .1.3.6.1.4.1.277.1.4.2.1.2 |
pportAdminTypeThe defined type of the board which the physical port is on.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.3 |
pportNumLportThe number of logical ports on the physical port.ro INTEGER .1.3.6.1.4.1.277.1.4.2.1.4 |
pportDataRateAn estimate of the physical port's data rate in bits
per second. The data rate can't be an arbitrary value. The
legal values are list below. Note that the T1/E1 class of
cards don't support this variable and return a 0
For UIO, DSX1:
9600, 19200, 38400, 48000, 56000, 64000,
128000, 192000, 256000, 320000, 384000, 448000,
512000, 576000, 640000, 704000, 768000, 832000,
896000, 960000, 1024000, 1088000, 1152000, 1216000,
1280000, 1344000, 1408000, 1472000, 1536000, 1600000,
1664000, 1728000, 1792000, 1856000, 1920000, 1984000,
2048000, 4096000, 6144000, 8192000
For HSSI:
1579000, 3158000, 4737000, 6316000, 7895000, 9474000,
11053000, 12632000, 14211000, 15790000, 17369000,
18948000, 20527000, 22106000, 23685000, 25264000,
26843000, 28422000, 30001000, 31580000, 33159000,
34738000, 36317000, 37896000, 39475000, 41054000,
42633000, 44212000, 45791000, 47370000, 48949000,
50528000
For ATM-IWU, TOPAZ OC3c:
155520000
For T1, E1, UT1, UE1, PRI, SH-T1:
0rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.5 |
pportTypeThe actual type of the physical port.ro Enumeration .1.3.6.1.4.1.277.1.4.2.1.6 |
pportRecvClockThe receive clock source. This object works in cooperation with
pportXmitClock.
The following are the various values for different clock
source types:
Type Clock Source pportRevClock pportXmitClock
{ pportEntry 7 } { pportEntry 8 }
V.35 DCE ............ 0 0
or UIO LoopTime DCE ... 3 0
DTE ............ 1 2
Direct Trunk ... 1 0
T1 or Loop Timed ..... 1 1
E1 Internal ....... 2 2
External ....... don't care 3ro INTEGER .1.3.6.1.4.1.277.1.4.2.1.7 |
pportXmitClockThe transmit clock source. This object works in cooperation with
pportXmitClock.
The following are the various values for different clock
source types:
Type Clock Source pportRevClock pportXmitClock
{ pportEntry 7 } { pportEntry 8 }
V.35 DCE ............ 0 0
or UIO LoopTime DCE ... 3 0
DTE ............ 1 2
Direct Trunk ... 1 0
T1 or Loop Timed ..... 1 1
E1 Internal ....... 2 2
External ....... don't care 3ro INTEGER .1.3.6.1.4.1.277.1.4.2.1.8 |
pportAdminStatusThe desired state of the physical port.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.9 |
pportOperStatusThe current state of the physical port.ro Enumeration .1.3.6.1.4.1.277.1.4.2.1.10 |
pportDs1LineTypeThe line type of the T1 or FT1-24B port. ANSI ESF is
equivalent to Bellcore ESF.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.11 |
pportDs1ZeroCodingThe variety of zero code suppression used on the T1
or FT1-24B link. Jammed bit is equivalent to dsx1JBZS
where the DS0s will run at 56K bps.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.12 |
pportDs1LineBuildoutThe line build out or line length specification for
the DS1 or DSX-1 transmitter. These values are card
specific:
10 port DSX-1 card
The accepted values are:
1 - 0 to 110 feet
2 - 110 to 220 feet
3 - 220 to 330 feet
4 - 330 to 440 feet
5 - 440 to 550 feet
6 - 550 to 660 feet
7 - over 655 feet
1-port and 4-port T1 cards
The accepted values are:
96 - 0 to 133 feet
128 - 133 to 266 feet
160 - 266 to 399 feet
192 - 399 to 533 feet
224 - 533 to 655 feet
96 - 0 db
32 - -7.5 db
64 - -15 db
4-port CBR card
The accepted values are:
96 - 0 db
32 - -7.5 db
64 - -15 db
4-port Short Haul T1 cards
The accepted values are:
96 - 0 to 133 feet
128 - 133 to 266 feet
160 - 266 to 399 feet
192 - 399 to 533 feet
224 - 533 to 655 feetrw INTEGER .1.3.6.1.4.1.277.1.4.2.1.13 |
pportDiagTestIdIdentification for the diagnostics tests to be run.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.14 |
pportDiagTestRunsThe number of passes of the diagnostics tests to be run.
The default value is 1.rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.15 |
pportInOctetsThe total number of octets received on the physical port,
including framing characters.ro Counter .1.3.6.1.4.1.277.1.4.2.1.16 |
pportInFramesThe total number of frames received on the physical port.ro Counter .1.3.6.1.4.1.277.1.4.2.1.17 |
pportInDiscardsThe total number of inbound frames discarded.ro Counter .1.3.6.1.4.1.277.1.4.2.1.18 |
pportInErrorsThe total number of inbound frames that contained erroneous
headers (e.g., illegal or unknown DLCIs).ro Counter .1.3.6.1.4.1.277.1.4.2.1.19 |
pportOutOctetsThe total number of octets transmitted out of the physical
port, including framing characters.ro Counter .1.3.6.1.4.1.277.1.4.2.1.20 |
pportOutFramesThe total number of frames transmitted out of the physical
port.ro Counter .1.3.6.1.4.1.277.1.4.2.1.21 |
pportOutDiscardsThe total number of outbound frames discarded due to
severe congestion.ro Counter .1.3.6.1.4.1.277.1.4.2.1.22 |
pportOutErrorsThe total number of outbound frames that causes xmit errors.ro Counter .1.3.6.1.4.1.277.1.4.2.1.23 |
pportDiagStateThe current state of the diagnostic on this physical port.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.24 |
pportDiagOptionStrOptional parameters to the diagnostic.rw OCTET STRING .1.3.6.1.4.1.277.1.4.2.1.25 |
pportDiagPassCountNumber of successful diagnostic passes.ro INTEGER .1.3.6.1.4.1.277.1.4.2.1.26 |
pportDiagFailCountNumber of failed diagnostic passes.ro INTEGER .1.3.6.1.4.1.277.1.4.2.1.27 |
pportDiagResultStrDescription of last diagnostic failure.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.4.2.1.28 |
pportLinkDownReasonReason why the link is down. The blue-alarm is equivalent
to the Alarm Indication Signal (AIS) failure.ro Enumeration .1.3.6.1.4.1.277.1.4.2.1.29 |
pportInterfaceActual interface connected to Multi-Interface Port or ATM-IWU.ro Enumeration .1.3.6.1.4.1.277.1.4.2.1.30 |
pportAdminInterfaceConfigured interface connected to Multi-Interface Port or ATM-IWU.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.31 |
pportCellScrambleConfigured ATM cell payload scrambling.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.32 |
pportCbitParityConfigured ATM DS3 C-bit Parity.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.33 |
pportMaxBufferSizeMaximum receive/transmit buffer size for the ATM UNI DS3 IOPrw INTEGER .1.3.6.1.4.1.277.1.4.2.1.34 |
pportPeakCellRate0Peak Cell Rate (cell/sec.) for rate queue #0.
rate queues 0 - 3 are high priorityrw INTEGER .1.3.6.1.4.1.277.1.4.2.1.35 |
pportPeakCellRate1Peak Cell Rate (cell/sec.) for rate queue #1.
rate queues 0 - 3 are high priorityrw INTEGER .1.3.6.1.4.1.277.1.4.2.1.36 |
pportPeakCellRate2Peak Cell Rate (cell/sec.) for rate queue #2.
rate queues 0 - 3 are high priorityrw INTEGER .1.3.6.1.4.1.277.1.4.2.1.37 |
pportPeakCellRate3Peak Cell Rate (cell/sec.) for rate queue #3.
rate queues 0 - 3 are high priorityrw INTEGER .1.3.6.1.4.1.277.1.4.2.1.38 |
pportPeakCellRate4Peak Cell Rate (cell/sec.) for rate queue #4.
rate queues 4 - 7 are low priorityrw INTEGER .1.3.6.1.4.1.277.1.4.2.1.39 |
pportPeakCellRate5Peak Cell Rate (cell/sec.) for rate queue #5.
rate queues 4 - 7 are low priorityrw INTEGER .1.3.6.1.4.1.277.1.4.2.1.40 |
pportPeakCellRate6Peak Cell Rate (cell/sec.) for rate queue #6.
rate queues 4 - 7 are low priorityrw INTEGER .1.3.6.1.4.1.277.1.4.2.1.41 |
pportPeakCellRate7Peak Cell Rate (cell/sec.) for rate queue #7.
rate queues 4 - 7 are low priorityrw INTEGER .1.3.6.1.4.1.277.1.4.2.1.42 |
pportInCellsThe total number of cells receivedro INTEGER .1.3.6.1.4.1.277.1.4.2.1.43 |
pportInErrorCellsThe total number of cells received with errorro INTEGER .1.3.6.1.4.1.277.1.4.2.1.44 |
pportOutCellsThe total number of cells transmittedro INTEGER .1.3.6.1.4.1.277.1.4.2.1.45 |
pportDs3LineBuildoutThe line build out or line length specification for
the DS3 transmitter.
1-port ATM-UNI DS3 card
The accepted values are:
1 - 0 to 225 feet
2 - 226 to 450 feetrw INTEGER .1.3.6.1.4.1.277.1.4.2.1.46 |
pportSetDS0LoopUpBit map used to set one or more DS0's into loopback. Low bit
corresponds to DS0 1. If a bit is set that DS0 is put into loopback.rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.47 |
pportSetDS0LoopDownBit map used to set one or more DS0's out of loopback. Low bit
corresponds to DS0 1. If a bit is set that DS0 is put out of loopback.rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.48 |
pportDS0LoopUpStatusBit map reporting which DS0's have gone into loopback since the
last time this variable was readro INTEGER .1.3.6.1.4.1.277.1.4.2.1.49 |
pportDS0LoopDownStatusBit map reporting which DS0's have gone out of loopback since the
last time this variable was readro INTEGER .1.3.6.1.4.1.277.1.4.2.1.50 |
pportDS0LoopStatusBit map reporting which DS0's are currently in loopback. Low bit
corresponds to DS0 1ro INTEGER .1.3.6.1.4.1.277.1.4.2.1.51 |
pportISDNSpecifies whether ISDN PRI is enabled for this physical portrw Enumeration .1.3.6.1.4.1.277.1.4.2.1.52 |
pportdsx3LoopbackConfigInteger used to set the loopback state of the DS3 or E3rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.53 |
pportdsx3SendCodeInteger used to send loopback code to far-end DS3rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.54 |
pportdsx3LoopStatusInteger indicating the current loopback status of the DS3 or E3ro Enumeration .1.3.6.1.4.1.277.1.4.2.1.55 |
pportdsx3FEACStatusInteger indicating the current DS3 FAEC status:
DS3 Equipment Failure (1),
DS3 LOS (2),
DS3 Out of Frame (4),
DS3 AIS received (8),
DS3 IDLE received (16),
DS3 Equipment-Failure (NSA) (32),
DS3 Common Equipment Failure (64),
DS3 Loopback received (128)ro INTEGER .1.3.6.1.4.1.277.1.4.2.1.56 |
pportds1LoopbackConfigInteger used to set the loopback state of the DS1rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.57 |
pportds1SendCodeInteger used to send loopback code to far-end DS1rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.58 |
pportds1LoopStatusInteger indicating the current loopback status of the DS1ro Enumeration .1.3.6.1.4.1.277.1.4.2.1.59 |
pportSetClkBkupThe desired clock source backup if the card is set in
external clock source modero Enumeration .1.3.6.1.4.1.277.1.4.2.1.60 |
pportAtmIdleWordThe word used to stuff the payload of the ATM idle cellrw INTEGER .1.3.6.1.4.1.277.1.4.2.1.61 |
pportAtmDisCardModeThe desired clock source backup if the card is set in
external clock source moderw Enumeration .1.3.6.1.4.1.277.1.4.2.1.62 |
pportAtmLastUnconfiguredVpiThis entry holds the Vpi read from the last Unconfigured
atm cell received. This entry applies to ATM pports
only.ro INTEGER .1.3.6.1.4.1.277.1.4.2.1.63 |
pportAtmLastUnconfiguredVciThis entry holds the Vci read from the last Unconfigured
atm cell received. This entry applies to ATM pports
only.ro INTEGER .1.3.6.1.4.1.277.1.4.2.1.64 |
pportAtmUnconfiguredCellsThis entry holds a count of the number of Unconfigured
ATM cells received. This entry applies to ATM pports
only.ro Counter .1.3.6.1.4.1.277.1.4.2.1.65 |
pportAtmNumBitsVCIThis entry holds a count of the VCI bits supppoted my this
ATM card.ro INTEGER .1.3.6.1.4.1.277.1.4.2.1.66 |
pportAtmNumBitsVPIThis entry holds a count of the VPI bits supppoted my this
ATM card.ro INTEGER .1.3.6.1.4.1.277.1.4.2.1.67 |
pportAtmInterfaceTypeInteger used to set ATM UNI or NNI typerw Enumeration .1.3.6.1.4.1.277.1.4.2.1.68 |
pportSonetSDHLoopbackConfigInteger used to set the loopback state of the Sonet/SDH portrw Enumeration .1.3.6.1.4.1.277.1.4.2.1.69 |
pportSonetSDHLoopStatusInteger indicating the current loopback status of the Sonet/SDH portro Enumeration .1.3.6.1.4.1.277.1.4.2.1.70 |
pportOutDiscardsCellThe total number of outbound cell discarded due to
congestion.ro Counter .1.3.6.1.4.1.277.1.4.2.1.71 |
pportAtmPlcpThe PLCP maintains the state of the ATM Physical Layer
Convergence Protocol. When the protocol is
disabled atm direct mapping is used with hec cell
delineation.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.72 |
pportCbrTargetClockModeThe clocking method to be used by the CBR card.
4-port CBR card
1 - synchronous (external) clocking
2 - SRTS clocking
3 - adaptive clock methodrw INTEGER .1.3.6.1.4.1.277.1.4.2.1.73 |
pportCbrCurrentClockModeThe clocking method currently used by the CBR card.
4-port CBR card
1 - synchronous (external) clocking
2 - SRTS clocking
3 - adaptive clock methodro INTEGER .1.3.6.1.4.1.277.1.4.2.1.74 |
pportClockMasterChannelThe number of the channel (lport) on this pport that is used as
ACM/SRTS master for this line interface:
4-port CBR E1/DS1 card (structured mode): 1..4rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.75 |
pportFibreTypeThe type of fibre connected to the ATM-IWU. Its type determines the
maximum transmission distance.
1-port ATM-IWU STM-1/STS-3c card
4 - multimode fibre (maximum transmission distance approx. 2 km)
2 - single mode fibre short haul (maximum transmission distance approx. 20 km)ro Enumeration .1.3.6.1.4.1.277.1.4.2.1.76 |
pportLaserStatusThe configured state of the laser:
1-port ATM-IWU STM-1/STS-3c card & Topaz 4-port OC3 & STM-1 card
1 - off
2 - onrw Enumeration .1.3.6.1.4.1.277.1.4.2.1.77 |
pportMaxActiveVpiBitsThe maximum number of active VPI bits configured for use at the ATM
interface. At the ATM UNI, the maximum number of active VPI bits
configured for use ranges from 0 to 8 only.rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.78 |
pportBipErrorsThreshThe threshold of BIP errors. If the number of line BIP-24/8
rrors persists to exceed this value, the pport will be taken down
and a trap will be issued:
1-port ATM-IWU STM-1/STS-3c card:
1 - ignore BIP errors
4 - 10^-4 errors
5 - 10^-5 errors
6 - 10^-6 errorsrw INTEGER .1.3.6.1.4.1.277.1.4.2.1.79 |
pportBipSectionErrorsThe number of B1 section BIP-8 errors since the last reset.ro Counter .1.3.6.1.4.1.277.1.4.2.1.80 |
pportBipLineErrorsThe number of line BIP-24/8 errors since the last reset.ro Counter .1.3.6.1.4.1.277.1.4.2.1.81 |
pportBipPathErrorsThe number of B3 path BIP-8 errors since the last reset.ro Counter .1.3.6.1.4.1.277.1.4.2.1.82 |
pportFebeErrorsThe number of line Far End Block Errors since the last reset.ro Counter .1.3.6.1.4.1.277.1.4.2.1.83 |
pportHcsErrorsThe number of correctable HCS errors since the last reset.ro Counter .1.3.6.1.4.1.277.1.4.2.1.84 |
pportHcsSevereErrorsThe number of uncorrectable HCS errors since the last reset.ro Counter .1.3.6.1.4.1.277.1.4.2.1.85 |
pportCongestedReceivedCellsThe number of received cells that were discarded due to congestion of
the ATM-IWU, since the last reset.ro Counter .1.3.6.1.4.1.277.1.4.2.1.86 |
pportCongestedTransmittedCellsThe number of cells to be transmitted, that were discarded due to
congestion of the ATM-IWU, since the last reset.ro Counter .1.3.6.1.4.1.277.1.4.2.1.87 |
pportAtmLayerErroredReceivedCellsThe number of received cells that were discarded due to ATM layer
errors, since the last reset.ro Counter .1.3.6.1.4.1.277.1.4.2.1.88 |
pportAtmLayerErroredTransmittedCellsThe number of cells to be transmitted, that were discarded due to ATM
layer errors, since the last reset.ro Counter .1.3.6.1.4.1.277.1.4.2.1.89 |
pportDS0BitStuffBit stuffing on or off for 2047 bit pattern in DS0 far end testing.rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.90 |
pportDS0BitErrorCountTotal number of errors in 2047 DS0 far end testing.ro INTEGER .1.3.6.1.4.1.277.1.4.2.1.91 |
pportDS0BitErrorFreeSecondsTotal number of error free seconds in 2047 DS0 far end testing.ro INTEGER .1.3.6.1.4.1.277.1.4.2.1.92 |
pportDS0BitErroredSecondsTotal number of errored seconds in 2047 DS0 far end testing.ro INTEGER .1.3.6.1.4.1.277.1.4.2.1.93 |
pportDS0MidspanRepeatersNumber of Midspan repeaters in a link to be punched thru
for DS0 far end testing.rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.94 |
pportDS0TestPatternSyncWhile DS0 far end testing, the DS0 pattern has detected the
pattern four consecutive times. If the pattern is lost, this variable
will be equal to one.ro INTEGER .1.3.6.1.4.1.277.1.4.2.1.95 |
pportDS0InjectBitErrorWhile testing DS0 far end lpbk, setting this variable will
inject a bit error into the test pattern.rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.96 |
pportDS0FarendLpbkTypeThe type of DS0 equipment to be looped back at the far end
during DS0 far end testing.
1 - OCU
2 - DSU
3 - CSU.rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.97 |
pportDS0LpbkModeThis determines what mode the DS0 Processor will be set to.
1 - no lpbk
2 - switch lpbk
3 - far end lpbk.rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.98 |
pportDS0SwitchLpbkStartThis is the first DS0 in a sting of consecutive DS0's to
be looped back at the switch if the DS0 processor is set to switch
loopback. If it's set to far end loopback, this determines which
singleton DS0 will be monitored at the receive end.rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.99 |
pportDS0SwitchLpbkEndThis is the Last DS0, +1, in a sting of consecutive DS0's to
be looped back at the switch if the DS0 processor is set to switch
loopback. If the DS0 processor is set to far end loopback, this value
will equal pportDS0SwitchLpbkStart + 1..rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.100 |
pportDS0FarendDS0InLpbkThis indicates the DS0 in far end loopback.ro INTEGER .1.3.6.1.4.1.277.1.4.2.1.101 |
pportDS0SendTestTrafficEnable or Disable sending DS0 2047 test pattern for DS0
far end testing.rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.102 |
pportOc3LoopConfigThe loopback state of the ATM IWU OC3rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.103 |
pportOc3LoopStatusThe current loopback status of the ATM IWU OC3ro Enumeration .1.3.6.1.4.1.277.1.4.2.1.104 |
pportISDNIpBaseAddrSpecifies the base address used for IP Dynamic Address Assignmentrw IpAddress .1.3.6.1.4.1.277.1.4.2.1.105 |
pportSonetSTM1ScrambleConfigured SONET/STM-1 scrambling.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.106 |
pportEFCIMarkingConfigured EFCI marking for cell traffic in Topaz IOMsrw Enumeration .1.3.6.1.4.1.277.1.4.2.1.107 |
pportAtmQOSTransmitModeSelect fix priority or weighted round-robin for cell transmission in different ATM QOS classes.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.108 |
pportHECModeConfigured ATM HEC single bit error correction routine.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.109 |
pportISDNChannelStatusThe ISDN call status of all the B-Channels on the pport are
encoded into this 24 character, (for T1 ISDN PRI card...23B+D) or 31 character,
(for E1 ISDN PRI card...30B+D ) ASCII string. The respective call state for
each B-Channel is represented in its corresponding bit position. The D-Channel
status is similarly encoded into the appropriate bit position (24th for T1) or
(16th for E1). The encoding legend is as follows...
I B-Channel is in Idle state
R B-Channel is in Dialing (Ringing) state
C B-Channel is in Connected (Active) state
H B-Channel is in Releasing (Hanging-up) state
U D-Channel is Up
D D-Channel is Downro OCTET STRING .1.3.6.1.4.1.277.1.4.2.1.110 |
pportds1FarEndLoopStatusDS1 Far End Loopback Status as commanded by the switchrw Enumeration .1.3.6.1.4.1.277.1.4.2.1.111 |
pportds1FDLControlEnables or Disables FDL Function for DS1 ESF pportrw Enumeration .1.3.6.1.4.1.277.1.4.2.1.112 |
pportds1FDLPrmXmitEnables or Disables transmission of Performance Monitoring Report
(PRM) messages on the DS1 ESF FDLrw Enumeration .1.3.6.1.4.1.277.1.4.2.1.113 |
pportds1FDLPidXmitEnables or Disables transmission of Path ID (PID) messages on
the DS1 ESF FDLrw Enumeration .1.3.6.1.4.1.277.1.4.2.1.114 |
pportds1FDLXmitPidTransmit Path Id to be sent on the DS1 ESF FDL. (76 bytes)rw OCTET STRING .1.3.6.1.4.1.277.1.4.2.1.115 |
pportds1FDLRcvPidThe last path id message received on the DS1 ESF FDL. (76 bytes)ro OCTET STRING .1.3.6.1.4.1.277.1.4.2.1.116 |
pportds1FDLRcvTsidThe last test id message received on the DS1 ESF FDL. (76 bytes)rw OCTET STRING .1.3.6.1.4.1.277.1.4.2.1.117 |
pportSonetSDHFramingModeThe Framing mode for SONET/SDH port interface types.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.118 |
pportds1InbandLoopTypeInteger used to distinguish Inband Line loopback code sent
from the switch when commanding inband line loopbacks, and
reckognized by the switch when responding to remote
loopback commandsrw Enumeration .1.3.6.1.4.1.277.1.4.2.1.119 |
pportESFDataLinkStatusThe current status of the DS1 ESF (FDL) data link.ro Enumeration .1.3.6.1.4.1.277.1.4.2.1.120 |
pportPMTcaIdThis object identifies the the most recently declared pport
threshold crossing alertrw Enumeration .1.3.6.1.4.1.277.1.4.2.1.121 |
pportBchanTimerValueThis value is used on a per port basis to add a delay to
answering a ISDN call of the initial Disconnect from the
network. This due to the ARP cache not updating quick
enough on the routersrw INTEGER .1.3.6.1.4.1.277.1.4.2.1.122 |
pportAAL5CRC32ErrorNumber of received AAL5 packets with CRC32 errors.ro Counter .1.3.6.1.4.1.277.1.4.2.1.123 |
pportAAL5CPIErrorNumber of received AAL5 packets with CPI errors
The only valid value currently defined for the CPI
field is all zerosro Counter .1.3.6.1.4.1.277.1.4.2.1.124 |
pportAAL5LengthErrorNumber of received AAL5 packets which satisfied one of the following
error conditions:
1. number of received cells * 48 bytes - length value in trailer > 55 bytes
2. number of received cells * 48 bytes - length value in trailer < 8 bytesro Counter .1.3.6.1.4.1.277.1.4.2.1.125 |
pportAAL5ReassemblyTimerErrorNumber of expired reassembly timersro Counter .1.3.6.1.4.1.277.1.4.2.1.126 |
pportAAL5MaxNrSegErrorNumber of received AAL5 packets which exceeds the maximum allowed lengthro Counter .1.3.6.1.4.1.277.1.4.2.1.127 |
pportRedundancyArchPport redundancy architecture. Default is disabled.
aps-intracard
aps-with-resilient-uni
cards, resilient UNI is used to reroute traffic.
aps-intercard-trunk-backup
cards, aps keeps phy layer in sync w/trunk backup.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.128 |
pportAPSadminDirProvisioned APS switch-direction-mode. Default is uni-
directional.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.129 |
pportAPSlineTypeAPS line type for the pport. Writable only when
pportRedundancyArch is disabled.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.130 |
pportAPSrevertiveModeAPS revertive mode. When revertive, after the condition
for an automatic switchover clears, user traffic will be
switched back to the working line after the pportAPSwtrPeriod
expires. Default is revertive.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.131 |
pportAPSpairedSlotIdSlot ID of the paired-with APS pport. Writable only when
pportRedundancyArch is disabled.rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.132 |
pportAPSpairedPportIdPport ID of the paired-with APS pport. Writable only when
pportRedundancyARch is disabled.rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.133 |
pportAPSsfBerThreshExponent N for APS Signal Failure based on BER. A line
bit-error-rate above 10^-N causes an SF BER failure to be
asserted. SF BER is cleared when the line BER returns to
less than 10^-7.rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.134 |
pportAPSsdBerThreshExponent N for APS Signal Degrade based on BER. A line
bit-error-rate above 10^-N causes an SD BER failure to be
asserted. SD BER is cleared when the line BER returns to
less than 10^-(N+1).rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.135 |
pportAPSwtrPeriodAPS wait-to-restore period. The number of minutes to
wait after an automatic switch condition clears before
switching back to the working line.rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.136 |
pportAPSprotectionLineStateIndicates the state of the protection line selector.
When selected, a protection switchover has taken place
and user traffic is being selected from the protection
line.ro Enumeration .1.3.6.1.4.1.277.1.4.2.1.137 |
pportAPSxCommandExternal switch commands. The clear command clears
any previously activated external command. Manual
switch is preemptable by auto-switch-requests (line
failures) while forced switch is not preemptable (except
if the protection line fails). Manual and forced switch
from protection to working, is valid only for 1+1 mode.
Exercise simulates a switchover using APS signalling
without actually performing a switch to protection line.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.138 |
pportAPSconfigStatusStatus of APS pport configuration. The not-configured
status indicates the pport APS feature is not configured
or it is a non-APS pport. The valid state indicates the
pport APS function is configured and has been validated
by the APS manager. The invalid state indicates that the
APS manager has detected a conflict between the working
line and protection line pport configurations. The user
must clear the invalid state by changing the configuration
of the misconfigured pport as soon as possible. Check
pportAPSadminDir, pportAPSlineType, pportAPSrevertiveMode,
and pportAPSwtrPeriod for any misconfigurations.ro Enumeration .1.3.6.1.4.1.277.1.4.2.1.139 |
pportAPSOperRxStatusThe current state of the pair of APS pports with respect
to the ability of the pair to Receive user traffic. When
indicated as up, user traffic may be received on at least
one of the ports in the APS pair.ro Enumeration .1.3.6.1.4.1.277.1.4.2.1.140 |
pportBertPatternPattern generated by the XBERTrw Enumeration .1.3.6.1.4.1.277.1.4.2.1.141 |
pportBertUserBytesDefinition of 1,2,3 or 4 byte pattern if UserNByte selected.rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.142 |
pportBertErrorRateError rate to insert in generated pattern.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.143 |
pportBertCommandSingle shot commands to the BERT.rw Enumeration .1.3.6.1.4.1.277.1.4.2.1.144 |
pportBertStatusCurrent status of the BERT for this channel.ro Enumeration .1.3.6.1.4.1.277.1.4.2.1.145 |
pportBertBitCountThe number of bits received - stops counting at 0xFFFFFFFFro Gauge .1.3.6.1.4.1.277.1.4.2.1.146 |
pportBertErrorCountThe number of bits received in error- stops counting
at 0xFFFFFFFFro Gauge .1.3.6.1.4.1.277.1.4.2.1.147 |
pportds1FELoopbackControlEnables or Disables Far end loopback control of the
switch. Enabled (2) = Loop up and down commands from far
end equipment will be processed. Disabled (1) - loop up
and down commands from far end equipment shall be ignored.
This control does not affect the switch's transmission of
loopback commands to the far endrw Enumeration .1.3.6.1.4.1.277.1.4.2.1.148 |
pportFT1DS0sDS0 usage bitmask for Fractional T1/E1 data rates.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.4.2.1.149 |
pportIMUXCntDS3 Inverse Multiplexer counter value - specifies number of idle
cells to insert by the outbound process Hardware.rw INTEGER .1.3.6.1.4.1.277.1.4.2.1.150 |
pportds1PMConfigThreshThe setting determines which standard is used for performance monitoring
configuration thresholdsrw Enumeration .1.3.6.1.4.1.277.1.4.2.1.151 |
lport OBJECT IDENTIFIER .1.3.6.1.4.1.277.1.5 |
ckt OBJECT IDENTIFIER .1.3.6.1.4.1.277.1.6 |
card OBJECT IDENTIFIER .1.3.6.1.4.1.277.1.7 |
cardNumberThe number of manageable cards physically present in this node.
Standby cards are not considered manageable.ro INTEGER .1.3.6.1.4.1.277.1.7.1 |
cardTableA list of cardEntry's. The number of entries is given by the value of
cardNumber SEQUENCE OF CardEntry .1.3.6.1.4.1.277.1.7.2 |
cardEntryThe card entry contains objects relevant to managing intelligent
cards. CardEntry .1.3.6.1.4.1.277.1.7.2.1 |
cardLogicalSlotIdThe logical slot number of this card. This is used as an index for
the cardTable. In redundant configurations, this can be the physical
slot number of either redundant card. In non redundant
configurations, this is the same as cardPhysicalSlotId.ro INTEGER .1.3.6.1.4.1.277.1.7.2.1.1 |
cardPhysicalSlotIdThe physical slot number of this card. This can be different from
cardLogicalSlotId in redundant configurations.ro INTEGER .1.3.6.1.4.1.277.1.7.2.1.2 |
cardAdminTypeThe desired card type.rw CardTypes .1.3.6.1.4.1.277.1.7.2.1.3 |
cardOperTypeThe actual card type.ro CardTypes .1.3.6.1.4.1.277.1.7.2.1.4 |
cardStateThe state of this card.ro Enumeration .1.3.6.1.4.1.277.1.7.2.1.5 |
cardAdminStatusThe desired status of this card.rw CardStatuses .1.3.6.1.4.1.277.1.7.2.1.6 |
cardOperStatusThe current status of this card.ro CardStatuses .1.3.6.1.4.1.277.1.7.2.1.7 |
cardDiagStatusThe current diagnostics status of this card, as determined by
background diagnostics.ro Enumeration .1.3.6.1.4.1.277.1.7.2.1.8 |
cardRedundConfigIs the card configured for redundancy?ro Enumeration .1.3.6.1.4.1.277.1.7.2.1.9 |
cardRedundSlotMaskA 32-bit mask indicating the slot position of this card and its
redundant partner. The low bit is slot 1 and the high bit is slot
32.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.10 |
cardRedundActualIs the card currently connected to a redundant card?ro Enumeration .1.3.6.1.4.1.277.1.7.2.1.11 |
cardRedundStateThe current redundancy state of this card. Exception: when
used as an index for the following objects: cardAdminType,
cardAdminCapability, and cardAdminStatus, the value 1 indicates
the card of the redundant pair in the lower-numbered slot, and
the value 2 indicates the card in the higher-numbered slot.ro Enumeration .1.3.6.1.4.1.277.1.7.2.1.12 |
cardToRedundantInstructs the standby card to reset the active card and take over
as new active card. The reset takes place after specified time ticks
have elapsed. A value of 0 indicates cancellation of the previously
scheduled request.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.7.2.1.13 |
cardDiagNonFatalSourceSource who reported last non-fatal error.ro Enumeration .1.3.6.1.4.1.277.1.7.2.1.14 |
cardDiagNonFatalTimeTime the last non-fatal error was reported.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.7.2.1.15 |
cardDiagNonFatalErrMajorMajor error code of last non-fatal error.ro INTEGER .1.3.6.1.4.1.277.1.7.2.1.16 |
cardDiagNonFatalErrMinorMinor error code of last non-fatal error.ro INTEGER .1.3.6.1.4.1.277.1.7.2.1.17 |
cardDiagNonFatalStrAscii string describing last non-fatal error.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.7.2.1.18 |
cardDiagFatalSourceSource who reported last fatal error.ro Enumeration .1.3.6.1.4.1.277.1.7.2.1.19 |
cardDiagFatalTimeTime the last fatal error was reported.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.7.2.1.20 |
cardDiagFatalErrMajorMajor error code of last fatal error.ro INTEGER .1.3.6.1.4.1.277.1.7.2.1.21 |
cardDiagFatalErrMinorMinor error code of last fatal error.ro INTEGER .1.3.6.1.4.1.277.1.7.2.1.22 |
cardDiagFatalStrAscii string describing last fatal error.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.7.2.1.23 |
cardDiagFatalRebootsNumber of times the switch has re-booted since last
fatal error was reported.ro Counter .1.3.6.1.4.1.277.1.7.2.1.24 |
cardDiagFatalAddressAddress switch was executing when it encountered fatal error.ro INTEGER .1.3.6.1.4.1.277.1.7.2.1.25 |
cardDiagBackgroundPassesNumber of passes made by the background diagnostics.ro Counter .1.3.6.1.4.1.277.1.7.2.1.26 |
cardDiagBackgroundFailuresNumber of failures discovered by background diagnostics.ro Counter .1.3.6.1.4.1.277.1.7.2.1.27 |
cardDiagBackgroundSuccessesNumber of successful passes by background diagnostics.ro Counter .1.3.6.1.4.1.277.1.7.2.1.28 |
cardDiagLEDResetChange the card state from marginal to active. Change the
LED from yellow to green.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.29 |
cardDiagPowerExtensiveShould power on diagnostics do slower, extensive testing,
or fast testing?rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.30 |
cardCpuUtilThe CPU utilization percentage for packet processing on this
intelligent card.ro Gauge .1.3.6.1.4.1.277.1.7.2.1.31 |
cardMemoryUsageThe memory utilization, in terms of free bytes, for
this intelligent card.ro Gauge .1.3.6.1.4.1.277.1.7.2.1.32 |
cardMaxVCsThe number of available VC entries on this card.ro Gauge .1.3.6.1.4.1.277.1.7.2.1.33 |
cardInUseVCsThe number of currently in use VC entries on this card.ro Gauge .1.3.6.1.4.1.277.1.7.2.1.34 |
cardFreeVCsThe number of currently free VC entries on this card.ro Gauge .1.3.6.1.4.1.277.1.7.2.1.35 |
cardInOctetsThe total number of octets received on this card, including
framing bytes.ro Counter .1.3.6.1.4.1.277.1.7.2.1.36 |
cardInPktsThe total number of packets received on this card.ro Counter .1.3.6.1.4.1.277.1.7.2.1.37 |
cardOutOctetsThe total number of octets transmitted out of this card,
including framing bytes.ro Counter .1.3.6.1.4.1.277.1.7.2.1.38 |
cardOutPktsThe total number of packets requested to be transmitted out
of this card, including those that were discarded or not sent.ro Counter .1.3.6.1.4.1.277.1.7.2.1.39 |
cardToWarmbootWarm boots the card after the specified time ticks have
elapsed. A value of 0 indicates cancellation of the previously
scheduled re-boot request.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.7.2.1.40 |
cardToColdbootCold boots the card after the specified time ticks have
elapsed. A value of 0 indicates cancellation of the previously
scheduled re-boot request.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.7.2.1.41 |
cardModelThe part number of the card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.7.2.1.42 |
cardSerialThe serial number of the card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.7.2.1.43 |
cardSwRevThe software rev number (major.minor).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.7.2.1.44 |
cardHwRevThe hardware rev number (major.minor).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.7.2.1.45 |
cardEpromRevThe EPROM firmware rev number (major.minor).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.7.2.1.46 |
cardNameThe name of this cardrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.7.2.1.47 |
cardCktGroupTrapThis is a ( 4 + n*134 ) byte octet string where n => 1.
The first and second byte is the interface/slot id of the
link/IOP going down or link goes up.
The third byte is the reason why circuits go down:
1 is a user link goes down,
2 is a trunk link goes down,
3 is an IOP goes down and
4 is an user link goes up
The fourth byte is the count of entries in the following
circuit bit map array.
Each circuit bit map entry is 134 bytes.
The first 2 bytes is the IOP slot on which dlci's are defined.
The second 2 bytes is the Physical port ID on which dlci's
are defined.
The third 2 bytes is the interface id on which dlci's are
defined.
The following 128 bytes (1024 bits) is a bit map for dlci's
defined on the interface. The left-most bit of the first byte
represent dlci 0 and the right-most bit of the 128th byte
represent dlci 1023. If a bit is set, it means the
corresponding dlci on that interface is up/down.ro OCTET STRING .1.3.6.1.4.1.277.1.7.2.1.48 |
cardOutBtusThe number of bus transfer units sent by this card.ro Counter .1.3.6.1.4.1.277.1.7.2.1.49 |
cardInGoodBtusThe number of good bus transfer units received by this card.ro Counter .1.3.6.1.4.1.277.1.7.2.1.50 |
cardInErrorBtusThe number of bus transfer units received with errors.ro Counter .1.3.6.1.4.1.277.1.7.2.1.51 |
cardInNoVcBtusThe number of bus transfer units discarded because no circuit
was found.ro Counter .1.3.6.1.4.1.277.1.7.2.1.52 |
cardInLinkDownBtusThe number of bus transfer units discarded because the outgoing
link was inactive.ro Counter .1.3.6.1.4.1.277.1.7.2.1.53 |
cardInNoBufferBtusThe number of bus transfer units discarded because no buffer
was available.ro Counter .1.3.6.1.4.1.277.1.7.2.1.54 |
cardInForwardBitBtusThe number of bus transfer units discarded because the circuit
forward bit was off.ro Counter .1.3.6.1.4.1.277.1.7.2.1.55 |
cardDiagTestIdIdentification of the diagnostics tests to be run.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.56 |
cardDiagTestRunsThe number of passes of the diagnostics tests to be run.
The default value is 1.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.57 |
cardDiagStateThe current state of the foreground diagnostics on this card.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.58 |
cardDiagOptionStrOptional parameters to the diagnostic.rw OCTET STRING .1.3.6.1.4.1.277.1.7.2.1.59 |
cardDiagPassesNumber of successful diagnostic passes.ro Counter .1.3.6.1.4.1.277.1.7.2.1.60 |
cardDiagFailuresNumber of failed diagnostic passes.ro Counter .1.3.6.1.4.1.277.1.7.2.1.61 |
cardDiagResultStringDescription of last diagnostic failure.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.7.2.1.62 |
cardFrameMemoryUtilThe percentage of frame memory utilization on this intelligent card.ro Gauge .1.3.6.1.4.1.277.1.7.2.1.63 |
cardResetPramSetting this to 1 causes a reset of PRAM on the corresponding
card.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.64 |
cardMemoryUtilThe percentage of system memory utilization on this intelligent card.ro Gauge .1.3.6.1.4.1.277.1.7.2.1.65 |
cardFrameMemoryUsageThe frame memory utilization, in terms of free bytes, for
this intelligent card.ro Gauge .1.3.6.1.4.1.277.1.7.2.1.66 |
cardUpTimeThe time (in hundredths of a second) since this card was last
booted.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.7.2.1.67 |
cardPramChecksumThe PRAM checksum for this card.ro INTEGER .1.3.6.1.4.1.277.1.7.2.1.68 |
cardPhysicalIndexThe physical slot id of this card.ro INTEGER .1.3.6.1.4.1.277.1.7.2.1.69 |
cardExternalClockRateThe external clock rate for DSX1, T1 and E1 cards. The
value is specified in units of 8KHz and can range from 1 to 255.ro INTEGER .1.3.6.1.4.1.277.1.7.2.1.70 |
cardShootStateSpecifies whether the system monitor on the CP should shoot
this card if it's unreachable. The default is enabled. The
card index used in the binding refers to a physical card.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.71 |
cardEraseAllWhen set to 1, erases program flash and PRAM on specified card.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.72 |
cardAdminCapabilityThe desired capability of the cardrw Enumeration .1.3.6.1.4.1.277.1.7.2.1.73 |
cardOperCapabilityThe actual capability of the cardro Enumeration .1.3.6.1.4.1.277.1.7.2.1.74 |
cardISDNswtypeSpecifies the ISDN central office switch type for the card.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.75 |
cardCpuFgUtilThe CPU foreground utilization percentage for packet
processing on this intelligent card.ro Gauge .1.3.6.1.4.1.277.1.7.2.1.76 |
cardTrkProtStateControl for issue of Link Trunk Protocol request frames. If
set to disabled, the issue of trunk protocol requests is
blocked for all trunks on this card.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.77 |
cardISDNSigTypeSpecifies whether the ISDN Signalling type is Associated or
Non-Facility Associated Signallingrw Enumeration .1.3.6.1.4.1.277.1.7.2.1.78 |
cardISDNChanIdSpecifies whether Channel ID assignment is performed by the
central office switch or the 9000 - Exclusive (central office)
Preferred (9000)rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.79 |
cardTransmitClockConfigThe transmit clock source for timing section of the cardrw Enumeration .1.3.6.1.4.1.277.1.7.2.1.80 |
cardTransmitClockSwitchOverEnable/disable automatic transmit clock source switch-over
once a failed clock reference has recovered.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.81 |
cardTransmitClockStatusThe transmit clock PLL synchronization status of the cardro Enumeration .1.3.6.1.4.1.277.1.7.2.1.82 |
cardSystemPrimaryClockPortConfigThe port number (1-x) on the card that specifies the system
primary clock source. A zero specifies no portrw INTEGER .1.3.6.1.4.1.277.1.7.2.1.83 |
cardSystemPrimaryClockStatusThe system primary clock status as detected on the card.
On the BIO, this refers to the Timing Module 1 clock
status as detected by the BIO.ro Enumeration .1.3.6.1.4.1.277.1.7.2.1.84 |
cardSystemSecondaryClockPortConfigThe port number (1 to x) on the card that specifies the system
secondary clock source. A zero specifies no portrw INTEGER .1.3.6.1.4.1.277.1.7.2.1.85 |
cardSystemSecondaryClockStatusThe system secondary clock status as detected on the card.
On the BIO, this refers to the Timing Module 2 clock
status as detected by the BIO.ro Enumeration .1.3.6.1.4.1.277.1.7.2.1.86 |
cardInCellsThe total number of cells received on this card.ro Counter .1.3.6.1.4.1.277.1.7.2.1.87 |
cardInErrorCellsThe total number of cells received on this card with HEC error.ro Counter .1.3.6.1.4.1.277.1.7.2.1.88 |
cardInErrorVPIVCIThe total number of cells received with HEC invalid VPI, VCI.ro Counter .1.3.6.1.4.1.277.1.7.2.1.89 |
cardOutCellsThe total number of cells transmitted out of this cardro Counter .1.3.6.1.4.1.277.1.7.2.1.90 |
cardOutDiscardCellsThe total number of cells discarded due to congestion on
this cardro Counter .1.3.6.1.4.1.277.1.7.2.1.91 |
cardQOSQueueSizeThe ATM QOS queue size (per cell) of each port on the cardro Enumeration .1.3.6.1.4.1.277.1.7.2.1.92 |
cardLastErrorPortThe port number (1 to x) of the last cell with invalid cell
header on the cardro INTEGER .1.3.6.1.4.1.277.1.7.2.1.93 |
cardLastErrorVPIThe VPI of the last cell with invalid cell header on the cardro INTEGER .1.3.6.1.4.1.277.1.7.2.1.94 |
cardLastErrorVCIThe VCI of the last cell with invalid cell header on the cardro INTEGER .1.3.6.1.4.1.277.1.7.2.1.95 |
cardSystemPrimaryClockModeConfigThe system primary clock mode. PLCP is for DS3 port onlyrw Enumeration .1.3.6.1.4.1.277.1.7.2.1.96 |
cardSystemSecondaryClockModeConfigThe system secondary clock mode. PLCP is for DS3 port onlyrw Enumeration .1.3.6.1.4.1.277.1.7.2.1.97 |
cardNFBDEStatusNon Fatal Background Diagnostic Error Statusrw Enumeration .1.3.6.1.4.1.277.1.7.2.1.98 |
cardProductCodeThis card's product code.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.7.2.1.99 |
cardMfgPNThis card's manufacturing part number.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.7.2.1.100 |
cardTotalUpTimeThis card's total accumulated up time, in hours.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.277.1.7.2.1.101 |
cardIOATypeThe type of IOA attached to this card.ro Enumeration .1.3.6.1.4.1.277.1.7.2.1.102 |
cardIOAHwRevThe attached IOA's hardware revision.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.7.2.1.103 |
cardIOASerialThe attached IOA's serial number.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.7.2.1.104 |
cardIOAProductCodeThe attached IOA's product code.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.7.2.1.105 |
cardIOAMfgPNThe attached IOA's manufacturing part number.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.7.2.1.106 |
cardDS0SupportSome B-Stdx T1 boards do not support lpbk.ro Enumeration .1.3.6.1.4.1.277.1.7.2.1.107 |
cardDiagParamIdParameter identifier for internal diagnostics.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.108 |
cardDiagParamValueValue assigned to parameter specified by cardDiagParamId.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.109 |
cardBulkStatsPeakCapabilityConfigures capability to collect peak 5-minute statistics.
Capability change takes effect upon IOM reboot.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.110 |
cardBulkStatsTotalCapabilityConfigures capability to collect total statistics.
Capability change takes effect upon IOM reboot.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.111 |
cardBulkStatsPeakEnableReflects the operational state of the peak 5-minute
statistic collection on an IOM. For this setting to be
enabled, the respective capability must be enabled.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.112 |
cardBulkStatsTotalEnableReflects the operational state of the total statistic
collection on an IOM. For this setting to be enabled,
the respective capability must be enabled.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.113 |
cardBulkStatsBaseCollectPeriodConfigures base collection period for bulk statistics
on an IOM in minutes. Only the following values are
allowed: 15, 20, 30, 60, 120, 180, 240, 360, 720, 1440.
The default value is 60.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.114 |
cardNrtsHwRevHardware revision of the NRTS processor.ro INTEGER .1.3.6.1.4.1.277.1.7.2.1.115 |
cardNrtsOutCellBufSizeThe size of the NRTS output cell buffer.ro INTEGER .1.3.6.1.4.1.277.1.7.2.1.116 |
cardNrtsOperStateThe operational status of the NRTS processor.ro Enumeration .1.3.6.1.4.1.277.1.7.2.1.117 |
cardNrtsAdminStateThe admin status of the NRTS processor.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.118 |
cardNrtsCcrmProtocolIdThe protocol ID field for the CCRM cells. Must be different
from the BCM protocol ID. Default is 6.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.119 |
cardNrtsBcmProtocolIdThe protocol ID field for the BCM cells. Must be different
from the CCRM protocol ID. Default is 5.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.120 |
cardNrtsRmGenIntervalThe RM cell generation interval in ms. Minimum is 30,
maximum is 250, default is 100.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.121 |
cardNrtsIdleCktThreshThe number of RM cell generation intervals with no cell
reception upon which the circuit is declared idle.
Minimum is 1, maximum is 8, default is 8.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.122 |
cardNrtsVbrNrtManageIndicates whether VBR NRT traffic should be managed by
the NRTS processor.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.123 |
cardNrtsIcrFactA factor used to calculate the Initial Cell Rate for a circuit
from its MCR and PCR.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.124 |
cardNrtsMcastDiscardThreshA NRTS discard threshold for the multicast circuits.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.125 |
cardNrtsMcastDiscardCountA NRTS discard counter for the multicast circuits.ro Counter .1.3.6.1.4.1.277.1.7.2.1.126 |
cardAdminIOATypeThe type of IOA attached to this card viewed from NMS.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.127 |
cardNrtsMcastRateThe NRTS shaping rate for multicast circuits as a fraction of
the line rate.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.128 |
cardMonStatusSet MON960 status, default(1) disable.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.129 |
cardImageSetAThe details of Image Set A. The elements of each
image are space delimited and include Part Number,
Revision, Size and Description. The details of each
image are linefeed delimited.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.7.2.1.130 |
cardImageSetBThe details of Image Set B. The elements of each
image are space delimited and include Part Number,
Revision, Size and Description. The details of each
image are linefeed delimited.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.7.2.1.131 |
cardMacAddressethernet MAC address of the card if there is an ethernet
interface. Currently only CP cards may have ethernet.
Cards without ethernet return 0 length octet string.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.7.2.1.132 |
cardFlashRevThe boot flash rev number.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.277.1.7.2.1.133 |
cardRequiredCapabilityBitmaskBitmask indicating this cards' required capabilities based on
configured features. A bit is set to one if the corresponding
capability is required. This variable is a bitmask so only
power-of-2 values can be assigned (1,2,4,8,16,etc.) .ro Enumeration .1.3.6.1.4.1.277.1.7.2.1.134 |
cardOperCapabilityBitmaskBitmask indicating this cards' actual capabilities. A bit is
set to one if the corresponding capability is supported.
This variable is a bitmask so only power-of-2 values can be
assigned (1,2,4,8,16,etc.).ro Enumeration .1.3.6.1.4.1.277.1.7.2.1.135 |
cardDslModuleThis is for Dynamic Software Loadl
You can type: ModuleName Version, ModuleName Version, ...
to load modules.rw OCTET STRING .1.3.6.1.4.1.277.1.7.2.1.136 |
cardIPTableSizeThe maximum number of IP routing table entries
supported by the card. If set to 0, routing table
size is assumed unlimited.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.137 |
cardIPTableStateState of the card's IP routing table. If set to
marginal, the routing table maximum size has
been exceeded. and all routes except management
prefixes have been discarded.ro Enumeration .1.3.6.1.4.1.277.1.7.2.1.138 |
cardATMTcaInBufOverflowAlertPeriodThe atm tca ingress buffer overflow alert
period (in min).rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.139 |
cardATMTcaInBufOverflowThreshThe atm tca ingress buffer overflow threshold.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.140 |
cardATMTcaInInvalidVpiVciAlertPeriodThe atm tca ingress invalid vpi/vci alert
period (in min).rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.141 |
cardATMTcaInInvalidVpiVciThreshThe atm tca ingress invalid vpi/vci threshold.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.142 |
cardATMTcaInATMDCFullAlertPeriodThe atm tca ingress ATM DC full alert period (in min).rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.143 |
cardATMTcaInATMDCFullThreshThe atm tca ingress ATM DC full threshold.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.144 |
cardATMTcaEnableThe atm tca enable/disable.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.145 |
cardATMTcaIdThis object identifies the the most recently declared card
ATM threshold crossing alertro Enumeration .1.3.6.1.4.1.277.1.7.2.1.146 |
cardATMTcaECidLookupFailureAlertPeriodThe atm tca ingress buffer overflow alert
period (in min).rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.147 |
cardATMTcaECidLookupThreshThe atm tca ingress buffer overflow threshold.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.148 |
cardATMTcaSPPearlOCbrFailureAlertPeriodThe atm tca sp pearl overflow CBR alert
period (in min).rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.149 |
cardATMTcaSPPearlOCbrThreshThe atm tca sp pearl overflow CBR threshold.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.150 |
cardATMTcaSPPearlOAbrFailureAlertPeriodThe atm tca sp pearl overflow ABR alert
period (in min).rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.151 |
cardATMTcaSPPearlOAbrThreshThe atm tca sp pearl overflow ABR threshold.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.152 |
cardATMTcaSPPearlOVbr1FailureAlertPeriodThe atm tca sp pearl overflow VBR1 alert
period (in min).rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.153 |
cardATMTcaSPPearlOVbr1ThreshThe atm tca sp pearl overflow VBR1 threshold.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.154 |
cardATMTcaSPPearlOVbr2FailureAlertPeriodThe atm tca sp pearl overflow VBR2 alert
period (in min).rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.155 |
cardATMTcaSPPearlOVbr2ThreshThe atm tca sp pearl overflow VBR2 threshold.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.156 |
cardATMTcaSPPearlGCbrFailureAlertPeriodThe atm tca sp pearl congestion CBR alert
period (in min).rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.157 |
cardATMTcaSPPearlGCbrThreshThe atm tca sp pearl congestion CBR threshold.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.158 |
cardATMTcaSPPearlGAbrFailureAlertPeriodThe atm tca sp pearl congestion ABR alert
period (in min).rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.159 |
cardATMTcaSPPearlGAbrThreshThe atm tca sp pearl congestion ABR threshold.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.160 |
cardATMTcaSPPearlGVbr1FailureAlertPeriodThe atm tca sp pearl congestion VBR1 alert
period (in min).rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.161 |
cardATMTcaSPPearlGVbr1ThreshThe atm tca sp pearl congestion VBR1 threshold.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.162 |
cardATMTcaSPPearlGVbr2FailureAlertPeriodThe atm tca sp pearl congestion VBR2 alert
period (in min).rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.163 |
cardATMTcaSPPearlGVbr2ThreshThe atm tca sp pearl congestion VBR2 threshold.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.164 |
cardATMTcaSPEnableThe atm tca SP enable/disable.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.165 |
cardSPEFCIEnableThe atm EFCI marking enable/disable.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.166 |
cardSPClpEnableThe atm CLP-1 enable/disable.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.167 |
spATMTcaIdThis object identifies the the most recently declared sp
ATM threshold crossing alert and first byte is used to indicate
the switching port number. i.e. sp 1 has spBufferOverflowC, then
the value is 0x1001ro Enumeration .1.3.6.1.4.1.277.1.7.2.1.168 |
cardSubcardToRedundantCommands the card to initiate an immediate protection
switch on the identified subcard that it controls. This
causes control to be switched from the active card to the
standby card.rw CardTypes .1.3.6.1.4.1.277.1.7.2.1.169 |
cardMemory5UsageThe bank5 memory utilization, in terms of free bytes, for
CP Oynx card only.ro Gauge .1.3.6.1.4.1.277.1.7.2.1.170 |
cardSF1OperStatusThe current status of Switch Fabric 1 (GX550).ro CardStatuses .1.3.6.1.4.1.277.1.7.2.1.171 |
cardSF2OperStatusThe current status of Switch Fabric 2 (GX550).ro CardStatuses .1.3.6.1.4.1.277.1.7.2.1.172 |
cardTM1OperStatusThe current status of Timing Module 1 (GX550).ro CardStatuses .1.3.6.1.4.1.277.1.7.2.1.173 |
cardTM2OperStatusThe current status of Timing Module 2 (GX550).ro CardStatuses .1.3.6.1.4.1.277.1.7.2.1.174 |
cardMemStartLogEnable/Disable Memory log record, 1 disable.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.175 |
cardMemLogLevelSet the Memory log level. Default 6rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.176 |
cardMemClrLogEnable/Disable Clear Memory log, 1 not clear.rw Enumeration .1.3.6.1.4.1.277.1.7.2.1.177 |
cardValidSubcardsThe number of manageable subcards physically present in this card.ro INTEGER .1.3.6.1.4.1.277.1.7.2.1.178 |
cardClp0CbrThresholdThe CLP 0 threshold for CBR queues in the card. Once queue
length reaches this threshold, all CLP 1 cells are discarded
until queue length falls below the threshold.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.179 |
cardClp01CbrThresholdThe maximum length of CBR queues in the card. Once queue
length reaches this threshold, all cells are discarded
until queue length falls below this threshold.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.180 |
cardClp0VbrRtThresholdThe CLP 0 threshold for VBR RT queues in the card. Once queue
length reaches this threshold, all CLP 1 cells are discarded
until queue length falls below the threshold.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.181 |
cardClp01VbrRtThresholdThe maximum length of VBR-RT queues in the card. Once queue
length reaches this threshold, all cells are discarded
until queue length falls below this threshold.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.182 |
cardClp0VbrNrtThresholdThe CLP 0 threshold for VBR NRT queues in the card. Once queue
length reaches this threshold, all CLP 1 cells are discarded
until queue length falls below the threshold.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.183 |
cardClp01VbrNrtThresholdThe maximum length of VBR-NRT queues in the card. Once queue
length reaches this threshold, all cells are discarded
until queue length falls below this threshold.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.184 |
cardClp0UAbrThresholdThe CLP 0 threshold for ABR/UBR queues in the card. Once queue
length reaches this threshold, all CLP 1 cells are discarded
until queue length falls below the threshold.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.185 |
cardClp01UAbrThresholdThe maximum length of UBR/ABR queues in the card. Once queue
length reaches this threshold, all cells are discarded
until queue length falls below this threshold.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.186 |
cardControlMessagesFromBusThe number of complete control Messages received over
the Cell Bus for this card.rw Counter .1.3.6.1.4.1.277.1.7.2.1.187 |
cardControlMessagesToBusThe number of complete control Messages transmitted by this
card over the Cell Bus.rw Counter .1.3.6.1.4.1.277.1.7.2.1.188 |
cardBTUsFromBusThe number of BTUs received by this card over the Cell Bus.rw Counter .1.3.6.1.4.1.277.1.7.2.1.189 |
cardBTUsToBusThe number of BTUs transmitted by this card over the Cell
Bus.rw Counter .1.3.6.1.4.1.277.1.7.2.1.190 |
cardInvalidPvcBTUsThe number of BTUs received by this card over the Cell Bus
with an invalid PVC identifier.rw Counter .1.3.6.1.4.1.277.1.7.2.1.191 |
cardIncompleteFramesFromBusThe number of partial frames received by this card over the
Cell Bus which were discarded due to missing BTUs.rw Counter .1.3.6.1.4.1.277.1.7.2.1.192 |
cardBTUsBusErrorsThe number of BTUs received by this card over the
Cell Bus which were discarded due to errors.rw Counter .1.3.6.1.4.1.277.1.7.2.1.193 |
cardBTUsNoResourceThe number of BTUs received by this card over the
Cell Bus which were discarded due to no free BTUs available
to replace it.rw Counter .1.3.6.1.4.1.277.1.7.2.1.194 |
cardInvalidPvcBTUsThresholdSend trap if the number of BTUs received by this card over
the Cell Bus with an invalid PVC identifier exceeds this
in a one minute interval. Zero value implies no check.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.195 |
cardIncompleteFramesFromBusThresholdSend trap if the number of partial frames received by this
card over the Cell Bus which were discarded due to missing
BTUs exceeds this in a one minute interval. Zero value
implies no check.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.196 |
cardBTUsBusErrorThresholdSend trap if the number of BTUs received by this card over
the Cell Bus which were discarded due to errors exceeds
this in a one minute interval. Zero value implies no check.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.197 |
cardBTUsNoResourceThresholdSend trap if the number of BTUs received by this card over
the Cell Bus which were discarded due to no free BTUs
available to replace it exceeds this in a one minute
interval. Zero value implies no check.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.198 |
cardFrameMemoryThresholdThe percentage of frame memory utilization on this card which
will generate a trap. Zero value implies no check.rw INTEGER .1.3.6.1.4.1.277.1.7.2.1.199 |
cardHoldQFrameMemoryThe frame memory utilization, in terms of bytes, currently
on the Hold Queues for this card.ro Counter .1.3.6.1.4.1.277.1.7.2.1.200 |
cardTotalAAL5RxErrorCountThe total number of Rx errors detected by the AAL5 processor
on this card.ro Counter .1.3.6.1.4.1.277.1.7.2.1.201 |
cardOperMemSizeThe total memory size on this card, in MB (1024 Kbytes).ro INTEGER .1.3.6.1.4.1.277.1.7.2.1.202 |
ds1 OBJECT IDENTIFIER .1.3.6.1.4.1.277.1.8 |
cascsmds OBJECT IDENTIFIER .1.3.6.1.4.1.277.2 |
smdsaddr OBJECT IDENTIFIER .1.3.6.1.4.1.277.2.1 |
namebinding OBJECT IDENTIFIER .1.3.6.1.4.1.277.3 |
isdnaddr OBJECT IDENTIFIER .1.3.6.1.4.1.277.4 |
cascsvc OBJECT IDENTIFIER .1.3.6.1.4.1.277.5 |
svcaddress OBJECT IDENTIFIER .1.3.6.1.4.1.277.5.1 |
svcmgt OBJECT IDENTIFIER .1.3.6.1.4.1.277.5.2 |
software OBJECT IDENTIFIER .1.3.6.1.4.1.277.6 |
provserver OBJECT IDENTIFIER .1.3.6.1.4.1.277.9 |