BREEZECOM-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for BREEZECOM-MIB.
290
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
290 total| Object Name |
|---|
breezecom OBJECT IDENTIFIER .1.3.6.1.4.1.710 |
breezecomPrvRev OBJECT IDENTIFIER .1.3.6.1.4.1.710.3 |
brznetmib OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2 |
brzSys OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.1 |
sysCmd OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.1.1 |
sysResetSetting the value of this attribute to ON is interpreted as a reset command for the system.rw Enumeration .1.3.6.1.4.1.710.3.2.1.1.1 |
sysSetDefaultsSetting the value of this attribute to ON will cause the system to set the NVRAM parameters to the factory default values. These values will become active after the next system resetrw Enumeration .1.3.6.1.4.1.710.3.2.1.1.2 |
sysResetCountersSetting the value of this attribute to ON will cause the system to clear the performance counters.rw Enumeration .1.3.6.1.4.1.710.3.2.1.1.3 |
sysTrapEnableSetting the value of this attribute to OFF will disable the system from sending TRAPs.rw Enumeration .1.3.6.1.4.1.710.3.2.1.1.4 |
sysTrapCounterThis attribute counts the total number of traps generated by the device, since initialization.ro Counter .1.3.6.1.4.1.710.3.2.1.1.5 |
sysCarrierSenseThis attribute defines the carrier sense absolute thresholdrw INTEGER .1.3.6.1.4.1.710.3.2.1.1.6 |
sysDeltaCarrierSenseThis attribute defines the carrier sense differential thresholdrw INTEGER .1.3.6.1.4.1.710.3.2.1.1.7 |
sysPartialDefaultsSetting the value of this attribute to ON will cause the system to set the partial NVRAM parameters to the factory default values. These values will become active after the next system resetrw Enumeration .1.3.6.1.4.1.710.3.2.1.1.8 |
sysRunFromNonActiveCodeThis attribute make you run from non active code. Automatic switch is done if the non active code is valid. To activate set to On. If the switch succeed no response will be sent to the SNMP browser.rw Enumeration .1.3.6.1.4.1.710.3.2.1.1.9 |
accessRights OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.1.1.10 |
sysDisplayAccessRightsThis attribute Display the access rights of that station.ro Enumeration .1.3.6.1.4.1.710.3.2.1.1.10.1 |
sysChangeRightsToUSERThis attribute let you change the access rights of that station to USER.rw Enumeration .1.3.6.1.4.1.710.3.2.1.1.10.2 |
sysChangeRightsToINSTALLERThis attribute let you change the access rights of that station to INSTALLER. Type the Installer password for the desired access right.rw DisplayString .1.3.6.1.4.1.710.3.2.1.1.10.3 |
sysChangeRightsToTECHNICIANThis attribute let you change the access rights of that station to AUTHORIZED TECHNICIAN. Type the Technician password for the desired access right.rw DisplayString .1.3.6.1.4.1.710.3.2.1.1.10.4 |
sysChangeInstallerPasswordThis attribute let you change the Installer Password of that station. Type the new password, maximum 8 characters.rw DisplayString .1.3.6.1.4.1.710.3.2.1.1.10.5 |
sysNoiseFloorThis attribute defines the low RSSI threshold in DBM units. Allowed range is from -120 to -50 dbm.rw INTEGER .1.3.6.1.4.1.710.3.2.1.1.11 |
sysExternalAmplifierThis attribute is set to 1 when external amplifier is connected to the device and set to 0 when device is connected to anntena.rw Enumeration .1.3.6.1.4.1.710.3.2.1.1.12 |
sysParams OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.1.2 |
brzHWMacAddressThe Hardware MAC address of the device.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.710.3.2.1.2.1 |
brzApplTunnelingThis attribute specifies the device tunneling mode, as follows: ipx - The device will enable IPX tunneling only. apple-talk - The device will enable AppleTalk tunneling only. none - The device will disable tunneling. both - The device will enable only IPX and AppleTalk tunneling.rw Enumeration .1.3.6.1.4.1.710.3.2.1.2.2 |
brzPositiveBrgThis attribute specifies the Wired to Wireless LAN bridging mode at the AP, as follows: reject-unknown - The AP forwards to the Wireless LAN only frames that are destined to associated stations. forward-unknown - The AP forwards to the Wireless LAN frames destined to associated AND unknown addresses. This value should be used only for Wireless Bridge installations. intelligent - If connected to a wireless bridge, the AP automatically activates the Forward-Unknown option. na - A not applicable value, for non-AP devices.rw Enumeration .1.3.6.1.4.1.710.3.2.1.2.3 |
brzIpFilterSetting the value of this attribute to ON will cause the system to filter all non-IP traffic to the Wireless LAN. This should be used on environments where only IP (and ARP) traffic is permitted.rw Enumeration .1.3.6.1.4.1.710.3.2.1.2.4 |
brzTranslationModeWhen this attribute is set to ON, data frames are being translated for the Wireless LAN transmission. If it is set to OFF, tunneling of data frames apply. All devices within the same Wireless LAN network, must have the same Translation Mode assigned.rw Enumeration .1.3.6.1.4.1.710.3.2.1.2.5 |
brzWIXSupportThis attribute applies to installations with collocated APs. When it is set to ON, a load balancing algorithm is activated, resulting with balanced Basic Service Sets (cells). This option may be set only at some of the stations in the network.rw Enumeration .1.3.6.1.4.1.710.3.2.1.2.6 |
brzWlanNetIDThis attribute identifies the Wireless LAN network name (Extended Service Set ID) for that device. Stations are not allowed to associate to APs with different Net IDs.rw DisplayString .1.3.6.1.4.1.710.3.2.1.2.7 |
brzAuthenticationTypeThis attribute indicates the authentication algorithm used during the authentication sequence. The value of this attribute is one of the following: 1 - Open System, 2 - Shared Key, 20 - Special Authentication Algorithm (#0), 21 - Special Authentication Algorithm (#1), 22 - Special Authentication Algorithm (#2).ro INTEGER .1.3.6.1.4.1.710.3.2.1.2.8 |
brzWlanRTNetIDThis attribute identifies the run-time Wireless LAN network name (Extended Service Set ID) for that device. Stations are not allowed to associate to APs with different Net IDs.ro DisplayString .1.3.6.1.4.1.710.3.2.1.2.9 |
brzApRedundancySupportSetting the value of this attribute to ON will cause the Access-Point to discontinue sending beacons to the Wireless LAN after no multicast or unicast frames for the cell arrive from the Ethernet during a period of 100 seconds. This option is available ONLY on AP (na value assigned in non-AP devices).rw Enumeration .1.3.6.1.4.1.710.3.2.1.2.10 |
brzWlanRelayUnicastThis attribute enables the relaying of unicast frames on the WLAN within the BSS. Setting this attribute to OFF means that unicast frames received from the WLAN by the AP can only be passed to the Distribution System. Applicable only in AP's.rw Enumeration .1.3.6.1.4.1.710.3.2.1.2.11 |
brzWlanRelayBroadcastThis attribute enables the relaying of broadcast frames on the WLAN within the BSS. Setting this attribute to OFF means that broadcast frames received from the WLAN by the AP can only be passed to the Distribution System. Applicable only in AP's.rw Enumeration .1.3.6.1.4.1.710.3.2.1.2.12 |
brzApRedundancyLimitThis attribute sets the time until an Access-Point discontinues sending beacons to the Wireless LAN when no multicast or unicast frames for the cell arrive from the Ethernet. This option is available ONLY on AP (na value assigned in non-AP devices).rw Enumeration .1.3.6.1.4.1.710.3.2.1.2.13 |
brzStaNumForLargeCWThis attribute sets the minimum number of stations in this cell that will cause this unit to use large CW, else this unit will use the default CW. (The value is in the range of 1-120)rw INTEGER .1.3.6.1.4.1.710.3.2.1.2.14 |
brzPowerMngModeThis attribute describes the current power management mode of the station. The allowed values are ACTIVE (for normal mode of operation), and POWER SAVE. An STA will always return an ACTIVE value.rw Enumeration .1.3.6.1.4.1.710.3.2.1.2.15 |
brzACKDelayedThis attribute applies to installations with collocated APs. When it is set to ON, a load balancing algorithm is activated, resulting with balanced Basic Service Sets (cells). This option may be set only at some of the stations in the network.rw Enumeration .1.3.6.1.4.1.710.3.2.1.2.16 |
brzDTIMPperiodThis attribute defines the rate of DTIM frames. The value is expressed in Beacon Intervals. This attribute is applicable only in AP's.rw INTEGER .1.3.6.1.4.1.710.3.2.1.2.17 |
brzPowerMngBitTestModeThis attribute describes the current power management bit test mode of the AP. The allowed values are DISABLED (for normal mode of operation), and ENABLED.rw Enumeration .1.3.6.1.4.1.710.3.2.1.2.18 |
brzBeaconIntervalThis attribute defines the rate of Beacon frames. The value is expressed in Dwells. This attribute is applicable only in AP's.rw INTEGER .1.3.6.1.4.1.710.3.2.1.2.19 |
brzPowerSaveSupportThis attribute defines the power save support. 0 - Power Save support disabled 1 - Power Save support enabled 2 - Enable Power Save support with PM bit test This attribute is applicable only in AP's.rw Enumeration .1.3.6.1.4.1.710.3.2.1.2.20 |
brzWlanAssocAgeThis attribute defines the Association Aging Period.rw INTEGER .1.3.6.1.4.1.710.3.2.1.2.21 |
brzEnableVoiceThis attribute Enables voice priority over other transmissions. This attribute is applicable only in AP's.rw Enumeration .1.3.6.1.4.1.710.3.2.1.2.22 |
brzNonActiveCodeStateThis attribute displays the current non active code state. WARNING: Activate this attribute will cause substantial degradation in station throughput, also answer is delayed!!!ro DisplayString .1.3.6.1.4.1.710.3.2.1.2.26 |
brzDisplayNonActiveCodeVersionThis attribute displays the active code version and the non active code version.ro DisplayString .1.3.6.1.4.1.710.3.2.1.2.27 |
brzIntelligentBridgingPeriodThis attribute defines the Intelligent Bridging Period in seconds.rw INTEGER .1.3.6.1.4.1.710.3.2.1.2.28 |
ipParams OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.2 |
trapHostsTableA list of trap-hosts entries. SEQUENCE OF TrapHostsEntry .1.3.6.1.4.1.710.3.2.2.1 |
trapHostsEntryA trap-receiving host entry, containing trap-host objects for a particular host. TrapHostsEntry .1.3.6.1.4.1.710.3.2.2.1.1 |
trapHostsIndexA unique value for each trap-host. Its value ranges between 1 and 3ro INTEGER .1.3.6.1.4.1.710.3.2.2.1.1.1 |
trapIPaddressThe IP address of the host to be sent all trapsrw IpAddress .1.3.6.1.4.1.710.3.2.2.1.1.2 |
trapCommunityThe community of the host to be sent all trapsrw DisplayString .1.3.6.1.4.1.710.3.2.2.1.1.3 |
ipAddrThe IP address of this device, used to access the device through any of its LAN Ports (Ethernet or WLAN).rw IpAddress .1.3.6.1.4.1.710.3.2.2.2 |
maskIPThe IP Network mask used by the IP entity when accessing devices through any of its LAN Ports (Ethernet or WLAN).rw IpAddress .1.3.6.1.4.1.710.3.2.2.3 |
readCommunityThe device read community. If updated, it will be used after the next reset.rw DisplayString -- .1.3.6.1.4.1.710.3.2.2.4 |
writeCommunityThe device write community. If updated, it will be used after the next reset.rw DisplayString -- .1.3.6.1.4.1.710.3.2.2.5 |
gatewayIPaddrGateway default IP address.rw IpAddress .1.3.6.1.4.1.710.3.2.2.6 |
brzIPStackThis attribute defines whether to use IP stack or not.rw Enumeration .1.3.6.1.4.1.710.3.2.2.7 |
brzWlan OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.3 |
brzWlanParams OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.3.1 |
brzMaxRateThis attribute indicates the rate (in Mbits per second) at which data will be transmitted across the medium. The default value of this attribute shall be 3.rw INTEGER .1.3.6.1.4.1.710.3.2.3.1.1 |
brzMobilLvlThis attribute indicates the expected mobility level of the system. The default value of this attribute is stationary.rw Enumeration .1.3.6.1.4.1.710.3.2.3.1.2 |
brzAvrgRssiA value representing the average Signal Strength for packets received from the current AP. This attribute is applicable only for a station (An AP will always return a value of 255).ro Enumeration .1.3.6.1.4.1.710.3.2.3.1.3 |
brzWlanProtocolThis attribute specifies the MAC/PHY protocol, utilized by this system. This attribute is not write accessible for regular users.rw INTEGER -- { -- 802-11 (10) -- } .1.3.6.1.4.1.710.3.2.3.1.4 |
brzWlanTrapThreasholdThis attribute specifies a threshold value, for sending the WlanStatusTRAP. When the Wireless LAN quality drops below (or goes above) this value, a trap will be issued.rw INTEGER .1.3.6.1.4.1.710.3.2.3.1.5 |
brzWlanQualityA measure for quality (and noise level) of the Wireless LAN.ro Enumeration .1.3.6.1.4.1.710.3.2.3.1.6 |
knownAPsTableA table of identities of the most recently known Access Points, and their signal quality. SEQUENCE OF KnownAPsEntry .1.3.6.1.4.1.710.3.2.3.1.7 |
knownAPsEntryAn entry in the Known APs table. KnownAPsEntry .1.3.6.1.4.1.710.3.2.3.1.7.1 |
knownAPsIndexA unique value, representing the index of the AP in the Known APs tablero INTEGER .1.3.6.1.4.1.710.3.2.3.1.7.1.1 |
knownAPsValueThis attributes specifies the address of a recently known AP. The default value of this attribute shall be null (an empty entry).rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.710.3.2.3.1.7.1.2 |
knownAPsQualityThis attribute specifies the current reception quality of frames, transmitted by that AP. At a station, a GOOD value indicates that the station can join that AP.ro Enumeration .1.3.6.1.4.1.710.3.2.3.1.7.1.3 |
knownAPsAvrgRssiA value representing the average Signal Strength for packets received from that AP in RSSI units.ro INTEGER .1.3.6.1.4.1.710.3.2.3.1.7.1.4 |
knownAPsStatusThe validity of the current entry, either invalid or valid.rw Enumeration .1.3.6.1.4.1.710.3.2.3.1.7.1.5 |
knownAPsLoadStationsA value representing the number of stations associated to that AP.ro INTEGER .1.3.6.1.4.1.710.3.2.3.1.7.1.6 |
knownAPsGoodBeaconsA value representing the number of beacons received with Strength more then join level from that AP.ro INTEGER .1.3.6.1.4.1.710.3.2.3.1.7.1.7 |
knownAPsTotalBeaconsA value representing the total number of beacons (good and bad) received from that AP.ro INTEGER .1.3.6.1.4.1.710.3.2.3.1.7.1.8 |
knownAPsAvrgDbmA value representing the average Signal Strength for packets received from that AP in DBN units.ro DisplayString .1.3.6.1.4.1.710.3.2.3.1.7.1.9 |
brzLastBeaconA value representing last dwell to receive beacon from that AP.ro INTEGER .1.3.6.1.4.1.710.3.2.3.1.8 |
brzBadBeaconsA value representing the number of beacons received with Strength less then join level from that AP.ro INTEGER .1.3.6.1.4.1.710.3.2.3.1.9 |
brzLoadStationsA value representing the number of stations associated to that AP.ro INTEGER .1.3.6.1.4.1.710.3.2.3.1.10 |
brzAvrgDBmA value representing the average Signal Strength for packets received from the current AP. This attribute is applicable only for a station (An AP will always return a value of -255).ro DisplayString .1.3.6.1.4.1.710.3.2.3.1.11 |
brzAP OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.3.2 |
bssInfo OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.3.2.1 |
bssNumOfStationsThis attribute specifies the number of devices, that are currently associated with this AP.ro INTEGER .1.3.6.1.4.1.710.3.2.3.2.1.1 |
bssNumOfStationsPeakThis attribute contains the maximum value that bssNumOfStations has reached.ro INTEGER .1.3.6.1.4.1.710.3.2.3.2.1.2 |
bssCollectPerStationInfoWhen this attribute is set to ON, the AP accumulates Wireless Link statistics per each station. This option is available only for the AP. At stations it is always assigned with na (Not Applicable) value. WARNING: Setting this attribute to ON can cause substantial degradation in cell throughput!!!rw Enumeration .1.3.6.1.4.1.710.3.2.3.2.1.3 |
bssNumOfBeaconSentThis attribute contains the total beacons sent counter.ro INTEGER .1.3.6.1.4.1.710.3.2.3.2.1.4 |
bssNumOfBeaconLostThis attribute contains the total beacons lost counter.ro INTEGER .1.3.6.1.4.1.710.3.2.3.2.1.5 |
bssNumOfStationsAuthenticatedThis attribute specifies the number of devices, that are currently Authenticated with this AP.ro INTEGER .1.3.6.1.4.1.710.3.2.3.2.1.6 |
bssNumOfStationsAuthenticatedPeakThis attribute contains the maximum value that bssNumOfStationsAuthenticated has reached.ro INTEGER .1.3.6.1.4.1.710.3.2.3.2.1.7 |
bssApAdb OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.3.2.2 |
adbTableA table of the stations associated. SEQUENCE OF AdbEntry .1.3.6.1.4.1.710.3.2.3.2.2.1 |
adbEntryAn entry in ADB table. AdbEntry .1.3.6.1.4.1.710.3.2.3.2.2.1.1 |
stAddressThe MAC Address of the station represented by this entry in the Association Data Basero MacAddress (SNMPv2-TC) .1.3.6.1.4.1.710.3.2.3.2.2.1.1.1 |
stCFModeThis attribute is set to ON if the station is in the Contention Free Polling list of the AP.ro Enumeration .1.3.6.1.4.1.710.3.2.3.2.2.1.1.4 |
stMaxRateThis attribute indicates the maximum rate (in Mbits per second) at which that station transmits data across the Wireless medium.ro INTEGER .1.3.6.1.4.1.710.3.2.3.2.2.1.1.5 |
stCurTxRateThe rate currently used by the AP to transmit packets to this stationro INTEGER .1.3.6.1.4.1.710.3.2.3.2.2.1.1.6 |
stRssiA value representing the average Signal Strength for packets received from that station in RSSI units. This attribute is being updated only if sysCollectPerStationInfo is set to ON.ro INTEGER .1.3.6.1.4.1.710.3.2.3.2.2.1.1.7 |
stPMModeThe current Power Management mode of this station Power saving mode enables WLAN units (such as laptops or hand-held devices) to conserve battery power. To enable this feature, first enable power saving for the AP, and then enable power saving in the SA-PCR Card.ro Enumeration .1.3.6.1.4.1.710.3.2.3.2.2.1.1.8 |
stTxFragmentsThis attribute counts the total number of fragments (including retransmissions), that were transmitted to that station over the Wireless LAN. It is updated only if sysCollectPerStationInfo is set to ON.ro Counter .1.3.6.1.4.1.710.3.2.3.2.2.1.1.9 |
stTxFragments1MThis attribute counts the total number of fragments (including retransmissions), that were transmitted to that station over the Wireless LAN in 1Mbps. It is updated only if sysCollectPerStationInfo is set to ON.ro Counter .1.3.6.1.4.1.710.3.2.3.2.2.1.1.10 |
stTxFragments2MThis attribute counts the total number of fragments (including retransmissions), that were transmitted to that station over the Wireless LAN in 2Mbps. It is updated only if sysCollectPerStationInfo is set to ON.ro Counter .1.3.6.1.4.1.710.3.2.3.2.2.1.1.11 |
stTxFragments3MThis attribute counts the total number of fragments (including retransmissions), that were transmitted to that station over the Wireless LAN in 3Mbps. It is updated only if sysCollectPerStationInfo is set to ON.ro Counter .1.3.6.1.4.1.710.3.2.3.2.2.1.1.12 |
stTxRetryThis attribute counts the total number of retransmissions to that station, over the Wireless LAN. It is updated only if sysCollectPerStationInfo is set to ON.ro Counter .1.3.6.1.4.1.710.3.2.3.2.2.1.1.13 |
stTxDroppedPacketsThis attribute counts the number of transmit frames (data or management) to this station, that were dropped because of too many retransmissions. It is updated only if sysCollectPerStationInfo is set to ON.ro Counter .1.3.6.1.4.1.710.3.2.3.2.2.1.1.14 |
stRxFragmentsThis attribute counts the total number of fragments (data and management) that have been received successfully from that station, through the Wireless LAN. It is updated only if sysCollectPerStationInfo is set to ON.ro Counter .1.3.6.1.4.1.710.3.2.3.2.2.1.1.15 |
stWlanStatusThis attribute specifies the current reception quality of frames, transmitted by that station.ro Enumeration .1.3.6.1.4.1.710.3.2.3.2.2.1.1.16 |
stResetCountersSetting the value of this attribute to ON, will clear the station counters at the AP (clear the counters in that adbEntry). Warning: Setting the value of this attribute to ON may cause momentary degradation in performancerw Enumeration .1.3.6.1.4.1.710.3.2.3.2.2.1.1.17 |
stTypeThis attribute identifies the device type of the station.ro Enumeration .1.3.6.1.4.1.710.3.2.3.2.2.1.1.18 |
stTxRetryPercentThis attribute calculate the retransmitted percentage, that was retransmitted to that station over the Wireless LAN.ro Counter .1.3.6.1.4.1.710.3.2.3.2.2.1.1.19 |
stReTxFragments1MThis attribute counts the total number of fragments, that was retransmitted to that station over the Wireless LAN in 1Mbps. It is updated only if sysCollectPerStationInfo is set to ON.ro Counter .1.3.6.1.4.1.710.3.2.3.2.2.1.1.20 |
stReTxFragments2MThis attribute counts the total number of fragments, that was retransmitted to that station over the Wireless LAN in 2Mbps. It is updated only if sysCollectPerStationInfo is set to ON.ro Counter .1.3.6.1.4.1.710.3.2.3.2.2.1.1.21 |
stReTxFragments3MThis attribute counts the total number of fragments, that was retransmitted to that station over the Wireless LAN in 2Mbps. It is updated only if sysCollectPerStationInfo is set to ON.ro Counter .1.3.6.1.4.1.710.3.2.3.2.2.1.1.22 |
stDbmA value representing the average Signal Strength for packets received from that station in DBM units. This attribute is being updated only if sysCollectPerStationInfo is set to ON.ro DisplayString .1.3.6.1.4.1.710.3.2.3.2.2.1.1.23 |
brzSTA OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.3.3 |
brzCurrentAPMacAddressHardware MAC address of the AP currently associated with. Available ONLY in station.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.710.3.2.3.3.1 |
brzLastAPMacAddressThe Hardware MAC address of the last AP that the station was associated with. Available ONLY in stations.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.710.3.2.3.3.2 |
brzPreferredAPMacAddressThe Hardware MAC address of the preferred AP, to which the station should associate when ever possible. Null value here indicates no preferences. Available ONLY in stations.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.710.3.2.3.3.3 |
brzRoamToAPMacAddressSetting this attribute to a specific AP MAC address, will cause the station to roam immediately to that AP, if possible. Available ONLY for stations.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.710.3.2.3.3.4 |
brzCFModeThis attribute is set to ON if the station required Contention Free services from the AP (hence it is in the AP's Contention Free list). This option is available ONLY on stations. A Not Applicable value is returned for all APs.ro Enumeration .1.3.6.1.4.1.710.3.2.3.3.5 |
brzTx1MBitRateTotal transmitted frames in 1 MBit rate.ro Counter .1.3.6.1.4.1.710.3.2.3.3.6 |
brzTx2MBitRateTotal transmitted frames in 2 MBit rate.ro Counter .1.3.6.1.4.1.710.3.2.3.3.7 |
brzTx3MBitRateTotal transmitted frames in 3 MBit rate.ro Counter .1.3.6.1.4.1.710.3.2.3.3.8 |
brzTotalRetxTotal Retransmitted frames including all rates.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.710.3.2.3.3.9 |
brzRoamParams OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.3.4 |
brzRoamDecisionWinThis parameter defines a minimum number of RSSI samples which is required to make a decision about the current WLAN channel quality. A new RSSI sample arrives with each incoming frame. Available ONLY in stations.rw INTEGER .1.3.6.1.4.1.710.3.2.3.4.1 |
brzRoamDecisionNumeratorThis parameter defines a maximum number of RSSI samples that is allowed to be below brzRoamDecisionRSSIThreshold, among a number equal to brzRoamDecisionWin of the last arrived samples. If a number of bad samples (i.e. below brzRoamDecisionRSSIThreshold) exceeds one, which is defined by this parameter, the channel is considered as bad. Available ONLY in stations.rw INTEGER .1.3.6.1.4.1.710.3.2.3.4.2 |
brzRoamDecisionRSSIThresholdIf an RSSI sample is bellow the value which is defined by this parameter the sample is considered as bad. Available ONLY in stations.rw INTEGER .1.3.6.1.4.1.710.3.2.3.4.3 |
brzJoinDecisionRSSIThresholdA station will join a new AP only if the AP transmits with an RSSI quality above the value which is defined by this parameter. Available ONLY in stations. In AP's, this is the threshold for sending Bad WLAN Conditions traps. If a station associated with the AP is heard at an RSII level below this threshold, a Bad WLAN Conditions trap is sent by the AP.rw INTEGER .1.3.6.1.4.1.710.3.2.3.4.4 |
brzNeighboringBeaconsThis parameters defines once in how many dwell times the AP will send a neighboring beacon. Available ONLY in AP's.rw INTEGER .1.3.6.1.4.1.710.3.2.3.4.5 |
brzNumberOfProbeResponsesIf a number of good RSSI samples coming from a neighbor is greater than or equal to this parameter the neighbor might be selected for joining.rw INTEGER .1.3.6.1.4.1.710.3.2.3.4.6 |
brzNumberOfBeaconsForDisconnectThis parameter defines a maximum number of consecutive not arrived Beacons that is allowed before a disconnect decision. Available ONLY in stations.rw INTEGER .1.3.6.1.4.1.710.3.2.3.4.7 |
brzMaxNumberOfScanningThis parameter defines a maximum number of scanning Attempts to perform before system reset. Zero is value for non reset. Available ONLY in stations.rw INTEGER .1.3.6.1.4.1.710.3.2.3.4.8 |
brzNeighboringBeaconRateThis parameter defines the Neighboring Beacon Rate in dwells. Zero is value for non Neighboring Beacons. Available ONLY in AP's.rw INTEGER .1.3.6.1.4.1.710.3.2.3.4.9 |
brzCnt OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.4 |
brzDSCnt OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.4.1 |
brzRxFromDSThis attribute counts the total number of frames that have been received successfully from the Wired Distribution system.ro Counter .1.3.6.1.4.1.710.3.2.4.1.1 |
brzRxBadFromDSThis attribute counts the number errored frames, received from the Wired Distribution system.ro Counter .1.3.6.1.4.1.710.3.2.4.1.2 |
brzRxOctetsFromDSThis attribute counts the total number of octets that have been received successfully from the Wired Distribution system.ro Counter .1.3.6.1.4.1.710.3.2.4.1.3 |
brzTxToDSThis attribute counts the total number of frames that have been transmitted to the Wired Distribution system.ro Counter .1.3.6.1.4.1.710.3.2.4.1.4 |
brzMissedFramesThis attribute counts the total number of missed frames that have missed the transmission to the Ethernet LAN.ro Counter .1.3.6.1.4.1.710.3.2.4.1.5 |
brzTxOctetsToDSThis attribute counts the total number of octets that have been transmitted successfully to the Wired Distribution system.ro Counter .1.3.6.1.4.1.710.3.2.4.1.6 |
brzRxOctetsForwardToWlanThis attribute counts the total number of octets that have been transmitted successfully to the Wireless LAN.ro Counter .1.3.6.1.4.1.710.3.2.4.1.7 |
brzRxForwardToWlanThis attribute counts the total number of packets that have been transmitted successfully to the Wireless LAN.ro Counter .1.3.6.1.4.1.710.3.2.4.1.8 |
brzWlanCnt OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.4.2 |
brzTxWlanCnt OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.4.2.1 |
brzTxPacketsToWlanThis attribute counts the total number of frames (data and management) that have been transmitted to the Wireless LAN.ro Counter .1.3.6.1.4.1.710.3.2.4.2.1.1 |
brzTxMSDUToWlanThis attribute counts the total number of frames (data frames) that have been transmitted to the Wireless LAN.ro Counter .1.3.6.1.4.1.710.3.2.4.2.1.2 |
brzDiscardedThis attribute counts the number of data frames, that were internally discarded in the system, instead of being transmitted over the Wireless LAN. High values of this counter indicate either very high traffic volume, or a noisy environment that prevents Wireless transmissions.ro Counter .1.3.6.1.4.1.710.3.2.4.2.1.3 |
brzTxFragToWlanThis attribute counts the total number of fragments (data and management) that have been transmitted to the Wireless LAN.ro Counter .1.3.6.1.4.1.710.3.2.4.2.1.4 |
brzRetryOnWlanThis attribute counts the total number of retransmitted fragments, on the Wireless LAN.ro Counter .1.3.6.1.4.1.710.3.2.4.2.1.5 |
brzFailedCountOnWlanThis attribute counts the number of frames that were dropped (not transmitted), due to the number of retransmits attempts exceeding the RetryMax value.ro Counter .1.3.6.1.4.1.710.3.2.4.2.1.6 |
brzRetryOnWlanPercentThis attribute calculates the percentage of number frames (to the data and management) that have been transmitted successfully Wireless LAN.ro Counter .1.3.6.1.4.1.710.3.2.4.2.1.7 |
brzRetryTxDataToWlanThis attribute counts the total number of data frames that have been retransmitted to the Wireless LAN.ro Counter .1.3.6.1.4.1.710.3.2.4.2.1.8 |
brzRetryTxDataToWlanPercentThis attribute calculates the percentage of data frames that have been transmitted successfully to the Wireless LAN.ro Counter .1.3.6.1.4.1.710.3.2.4.2.1.9 |
brzTotalTxPacketsToWlanThis attribute counts the total number frames (data and management) that have been transmitted to the Wireless LAN.ro Counter .1.3.6.1.4.1.710.3.2.4.2.1.10 |
brzTxErrTransmitions OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.4.2.1.15 |
brzTxErrorAckTimeOutThis attribute counts the total number of acknowledge timeouts on the Wireless LAN.ro Counter .1.3.6.1.4.1.710.3.2.4.2.1.15.1 |
brzTxErrorAckCRCThis attribute counts the total number of acknowledge CRC Errors on the Wireless LAN.ro Counter .1.3.6.1.4.1.710.3.2.4.2.1.15.2 |
brzTxErrorNoTimeUntilHopThis attribute counts the total number of timeouts caused of on time until end of hop on the Wireless Cell.ro Counter .1.3.6.1.4.1.710.3.2.4.2.1.15.3 |
brzTxErrorUnderRunAndCTSThis attribute counts the total number of errors caused by HW problems (Under Run).ro Counter .1.3.6.1.4.1.710.3.2.4.2.1.15.4 |
brzTxErrorAbortThis attribute counts the total number of errors caused by frame abortion from Boori.ro Counter .1.3.6.1.4.1.710.3.2.4.2.1.15.5 |
brzTxErrorFrameReceivedThis attribute counts the total number of errors caused by frame failure on the Wireless LAN.ro Counter .1.3.6.1.4.1.710.3.2.4.2.1.15.6 |
brzRxWlanCnt OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.4.2.2 |
brzRxPacketsFromWlanThis attribute counts the total number of frames (data and management) that have been received successfully from the Wireless LAN.ro Counter .1.3.6.1.4.1.710.3.2.4.2.2.1 |
brzRxMSDUFromWlanThis attribute counts the total number of MSDUs (data frames) that have been received successfully from the Wireless LAN.ro Counter .1.3.6.1.4.1.710.3.2.4.2.2.2 |
brzRxFragFromWlanThis attribute counts the number of fragments (data and management), that have been received successfully from the Wireless LAN.ro Counter .1.3.6.1.4.1.710.3.2.4.2.2.3 |
brzRxBadFragFromWlanThis counter is incremented when an error is detected in a fragment, received from the Wireless LAN.ro Counter .1.3.6.1.4.1.710.3.2.4.2.2.4 |
brzRxDuplicateFragFromWlanThis counter is incremented when a duplicated fragment is received from the Wireless LAN.ro Counter .1.3.6.1.4.1.710.3.2.4.2.2.5 |
freqStatisticsTableA table for the traffic statistics of each frequency. SEQUENCE OF FreqStatisticsEntry .1.3.6.1.4.1.710.3.2.4.2.2.6 |
freqStatisticsEntryAn entry in the Frequencies Statistics table. FreqStatisticsEntry .1.3.6.1.4.1.710.3.2.4.2.2.6.1 |
freqStatisticsIndexA unique value, representing the index of the frequency in the hopping sequence tablero INTEGER -- .1.3.6.1.4.1.710.3.2.4.2.2.6.1.1 |
freqNoThis attributes specifies the channel number of the frequency, for which this entry accumulates the statistics.ro INTEGER -- .1.3.6.1.4.1.710.3.2.4.2.2.6.1.2 |
freqTotalReceivedThis attribute counts the total number of frames (data and management) that have been received successfully from the Wireless LAN, in that specific frequency.ro Counter .1.3.6.1.4.1.710.3.2.4.2.2.6.1.3 |
brzRoamCnt OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.4.3 |
brzNumOfReassocRequestsFor an AP: The number of Associations and ReAssociations requests, received since the last reset of the AP. This counter is useful for getting information about mobility activity on the BSS. For a Station: The number of Associations and ReAssociation requests issued by the station since the last reset.ro Counter .1.3.6.1.4.1.710.3.2.4.3.1 |
brzMngCnt OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.4.4 |
brzMngAP OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.4.4.1 |
probeResponseSentFor an AP: Number of Probe response that sent.ro Counter .1.3.6.1.4.1.710.3.2.4.4.1.1 |
probeResponseLostFor an AP: Number of Probe response that got lost.ro Counter .1.3.6.1.4.1.710.3.2.4.4.1.2 |
probeResponseSentRetxFor an AP: Number of retransmitted Probe response frames that sent.ro Counter .1.3.6.1.4.1.710.3.2.4.4.1.3 |
probeRequestReciveFor an AP: Number of Probe request frames that has received.ro Counter .1.3.6.1.4.1.710.3.2.4.4.1.4 |
assocResponseSentFor an AP: Number of Association response frames that sent.ro Counter .1.3.6.1.4.1.710.3.2.4.4.1.5 |
assocResponseLostFor an AP: Number of Association response frames that got lost.ro Counter .1.3.6.1.4.1.710.3.2.4.4.1.6 |
assocResponseSentRetxFor an AP: Number of retransmitted Association response frames that sent.ro Counter .1.3.6.1.4.1.710.3.2.4.4.1.7 |
assocRequestReciveFor an AP: Number of Association request frames that has received.ro Counter .1.3.6.1.4.1.710.3.2.4.4.1.8 |
reAssocRequestReciveFor an AP: Number of ReAssociation request frames that has received.ro Counter .1.3.6.1.4.1.710.3.2.4.4.1.9 |
brzMngSAWB OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.4.4.2 |
probRequestSentFor WB or SA: Number of Probe request frames that sent.ro Counter .1.3.6.1.4.1.710.3.2.4.4.2.1 |
probResponceReciveFor WB or SA: Number of received Probe response frames.ro Counter .1.3.6.1.4.1.710.3.2.4.4.2.2 |
authRequestSentFor WB or SA: Number of Authentication request frames that sent.ro Counter .1.3.6.1.4.1.710.3.2.4.4.2.3 |
authRequestSentRetxFor WB or SA: Number of Retransmitted Authentication request frames that sent.ro Counter .1.3.6.1.4.1.710.3.2.4.4.2.4 |
authResponceReciveFor WB or SA: Number of received Authentication response frames.ro Counter .1.3.6.1.4.1.710.3.2.4.4.2.5 |
assocRequestSentFor WB or SA: Number of Association request frames that sent.ro Counter .1.3.6.1.4.1.710.3.2.4.4.2.6 |
assocRequestSentRetxFor WB or SA: Number of Retransmitted Association request frames that sent.ro Counter .1.3.6.1.4.1.710.3.2.4.4.2.7 |
assocResponceReciveFor WB or SA: Number of received Association response frames.ro Counter .1.3.6.1.4.1.710.3.2.4.4.2.8 |
brzPSCnt OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.4.5 |
pSFreeEntriesFor an AP: Number of station free entries.ro Counter .1.3.6.1.4.1.710.3.2.4.5.1 |
pSInternallydiscardedFor an AP: Number of Internally Discarded frames.ro Counter .1.3.6.1.4.1.710.3.2.4.5.2 |
pSstationsFor an AP: Number of power saved station connected to this AP.ro Counter .1.3.6.1.4.1.710.3.2.4.5.3 |
pSPowerSavingAgedFor an AP: Number of frames that were not transmitted due to the end of aging time.ro Counter .1.3.6.1.4.1.710.3.2.4.5.4 |
powreStationsTableA list of trap-hosts entries. SEQUENCE OF PowreStationsEntry .1.3.6.1.4.1.710.3.2.4.5.5 |
powreStationsEntryA trap-receiving host entry, containing trap-host objects for a particular host. PowreStationsEntry .1.3.6.1.4.1.710.3.2.4.5.5.1 |
powerSaveIndexA unique value, representing the index of the frequency in the hopping sequence tablero INTEGER .1.3.6.1.4.1.710.3.2.4.5.5.1.1 |
powerSaveStationIDThe identifier numerator of the Station in the AP. Note : ID zero is Broadcast.ro INTEGER .1.3.6.1.4.1.710.3.2.4.5.5.1.2 |
powerSaveBufferedThis attributes specifies how many messages are waiting to that Station in the AP buffersro INTEGER .1.3.6.1.4.1.710.3.2.4.5.5.1.3 |
powerSaveAgedThis attributes specifies how many Stations were deleted after long time of waitingro INTEGER .1.3.6.1.4.1.710.3.2.4.5.5.1.4 |
powerSaveSentThis attributes specifies how many messages were sent to that stationro INTEGER .1.3.6.1.4.1.710.3.2.4.5.5.1.5 |
powerSaveQueueFullThis attributes specifies how many messages were discarded because the queue to that station was fullro INTEGER .1.3.6.1.4.1.710.3.2.4.5.5.1.6 |
brzTraps OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.5 |
brzTrapAPMacAddrThe MAC address of an APro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.710.3.2.5.1 |
brzTrapSTAMacAddrThe MAC address of a station devicero MacAddress (SNMPv2-TC) .1.3.6.1.4.1.710.3.2.5.2 |
brzTrapMacAddressA STA or AP MAC addressro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.710.3.2.5.3 |
brzTrapRssiQualityThe RSSI level of the signal received from the Access Pointro INTEGER .1.3.6.1.4.1.710.3.2.5.4 |
brzTrapLastRssiQualityThe RSSI level of the signal received from the previous Access Pointro INTEGER .1.3.6.1.4.1.710.3.2.5.5 |
brzTrapIndexIndex number for future trap implementationro INTEGER .1.3.6.1.4.1.710.3.2.5.6 |
brzTrapTextTextual string for future trap implementationro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.710.3.2.5.7 |
brzTrapToggleA general ON/OFF toggle value, for the traps.ro Enumeration .1.3.6.1.4.1.710.3.2.5.8 |
brzTrapSTATypeThis attribute identifies the device type of the station.ro Enumeration .1.3.6.1.4.1.710.3.2.5.9 |
brzdot11 OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.6 |
dot11smt OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.6.1 |
dot11DefaultWEPKeys OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.6.1.3 |
dot11DefaultWEPKey1This attribute indicates the WEP secret key value corresponding to KeyID 1. The WEP secret key is logically WRITE-ONLY. Attempts to read this attribute shall return a string of asterisks (enter exactly 10 Hex-Decimal digits).rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.710.3.2.6.1.3.1 |
dot11DefaultWEPKey2This attribute indicates the WEP secret key value corresponding to KeyID 2. The WEP secret key is logically WRITE-ONLY. Attempts to read this attribute shall return a string of asterisks (enter exactly 10 Hex-Decimal digits).rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.710.3.2.6.1.3.2 |
dot11DefaultWEPKey3This attribute indicates the WEP secret key value corresponding to KeyID 3. The WEP secret key is logically WRITE-ONLY. Attempts to read this attribute shall return a string of asterisks (enter exactly 10 Hex-Decimal digits).rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.710.3.2.6.1.3.3 |
dot11DefaultWEPKey4This attribute indicates the WEP secret key value corresponding to KeyID 4. The WEP secret key is logically WRITE-ONLY. Attempts to read this attribute shall return a string of asterisks (enter exactly 10 Hex-Decimal digits).rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.710.3.2.6.1.3.4 |
dot11PrivacyGrp OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.6.1.6 |
dot11PreauthenticationThis attribute, when true, enables Preauthentication algorithm.rw Enumeration .1.3.6.1.4.1.710.3.2.6.1.6.1 |
dot11PrivacyOptionImplementedThis attribute, when true, shall indicate that the 802.11 WEP option is implemented.ro Enumeration .1.3.6.1.4.1.710.3.2.6.1.6.2 |
dot11PrivacyInvokeThis attribute indicates if a special mechanism is invoked, to protect the Wireless LAN transmissions. The value is one of the following: 1 - Standard WEP, 2 - No Encryption, 20 - Special Encryption (#0), 21 - Special Encryption (#1), 22 - Special Encryption (#2)ro INTEGER .1.3.6.1.4.1.710.3.2.6.1.6.3 |
dot11WEPDefaultKeyIDThis attribute shall indicate the use of the first, second, third or fourth DefaultWEPKey when set to values of one, two, three or four.rw INTEGER -- .1.3.6.1.4.1.710.3.2.6.1.6.4 |
dot11mac OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.6.2 |
dot11OperationGrp OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.6.2.1 |
dot11MaxMulticastRateThis attribute indicates the basic rate for multicast frames.rw INTEGER .1.3.6.1.4.1.710.3.2.6.2.1.1 |
dot11DwellTimeThis attribute indicates the dwell time in Kilo-microsecond Allowed Values for version 5.x.x and higher are between 19..390. For older versions values are between 1 - 3. This attribute is available only in AP's.rw INTEGER .1.3.6.1.4.1.710.3.2.6.2.1.2 |
dot11RTSThresholdThis attribute indicates the number of bytes in an MPDU (frame), above which an RTS/CTS handshake will be performed. Setting this attribute to be larger than the maximum frame size, will prevent the RTS/CTS handshake for frames transmitted by this station.rw INTEGER .1.3.6.1.4.1.710.3.2.6.2.1.3 |
dot11ShortRetryLimitThis attribute indicates the number of retransmission attempts made, before a failure condition is indicated. Values between 0..20 .rw INTEGER .1.3.6.1.4.1.710.3.2.6.2.1.4 |
dot11DwellRetryLimitThis attribute indicates the number of retransmission attempts made in several Dwells, before a failure condition is indicated. Values between 0..9 .rw INTEGER .1.3.6.1.4.1.710.3.2.6.2.1.5 |
dot11FragmentationThresholdThis attribute specifies the current maximum size, in octets, of the MPDU that will be delivered to the PHY. A frame will be broken into fragments if its size exceeds the value of this attribute, after adding MAC header and tailors. The value is one of the following: 1 - 560 octets, 2 - 800 octets, 3 - 1518 octets.rw INTEGER .1.3.6.1.4.1.710.3.2.6.2.1.6 |
dot11ShortRetryLimitForVoiceThis attribute indicates the number of retransmission for voice attempts made, before a failure condition is indicated. Values between 0..9 . This option is only for AP's.rw INTEGER .1.3.6.1.4.1.710.3.2.6.2.1.7 |
dot11DwellRetryLimitForVoiceThis attribute indicates the number of retransmission for voice attempts made in several Dwells, before a failure condition is indicated. Values between 0..5 . This option is only for AP's.rw INTEGER .1.3.6.1.4.1.710.3.2.6.2.1.8 |
dot11res OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.6.3 |
dot11resAttribute OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.6.3.8 |
dot11ResourceInfo OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.6.3.8.2 |
dot11CurrentStationStatusThis attribute identifies the current Station Wlan status. This attribute is not available in AP's.ro DisplayString .1.3.6.1.4.1.710.3.2.6.3.8.2.1 |
dot11TotalNumberOfAssocSinceLastResetThis attribute identifies how many time the device Associated since startup.ro Counter .1.3.6.1.4.1.710.3.2.6.3.8.2.2 |
dot11manufacturerNameThis attribute identifies the manufacturer of the resource.ro DisplayString .1.3.6.1.4.1.710.3.2.6.3.8.2.3 |
dot11manufacturerProductNameThis attribute identifies the manufacturer product name of the resource.ro DisplayString .1.3.6.1.4.1.710.3.2.6.3.8.2.4 |
dot11manufacturerProductVersionThis attribute identifies the manufacturer's product version of the resource.ro DisplayString .1.3.6.1.4.1.710.3.2.6.3.8.2.5 |
dot11phy OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.6.4 |
dot11PhyOperationGrp OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.6.4.1 |
dot11CurrentRegDomainThis attribute specifies the regularity domain, for the radio operation of this device. This integer contains an 8 bit value, as defined below: 00h - EthAirNet, 10h - USA, 20h - Canada, 30h - Europe, 31h - Spain, 32h - France, 37h - Europe Double Deviation, 38h - Netherlands, 40h - Japan, 41h - Korea, 48h - Israel, 49h - Australia, 60h - Proprietary.rw Enumeration .1.3.6.1.4.1.710.3.2.6.4.1.3 |
dot11PhyAntennaGrp OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.6.4.3 |
dot11CurrentTxAntennaThis attribute specifies the current antenna being used to transmit. The value is one of the following: 0 - Intelligent antennas selection, 1 - Transmitting only with antenna 1, 2 - Transmitting always with antenna 2.rw INTEGER .1.3.6.1.4.1.710.3.2.6.4.3.2 |
dot11PhyTxPwrGrp OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.6.4.4 |
dot11CurrentTxPwrLvlThis attribute specifies the power level, currently being used to transmit data. The value is one of the following: 0 - Low, or 1 - High.rw Enumeration .1.3.6.1.4.1.710.3.2.6.4.4.11 |
dot11PhyFHSSGrp OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.6.4.5 |
dot11CurrentDwellTimeThis attribute specifies the current time, in Kilo-microseconds, that the radio operates on a single channel. The value is from 19 - 390. The same Dwell Time value should be assigned to all the devices within the same Wireless LAN network.rw INTEGER .1.3.6.1.4.1.710.3.2.6.4.5.5 |
dot11CurrentSetThis attribute represents the current set of patterns that the device is using to determine the hop sequence. The range of values is 1 to 3, and the default is 1.rw INTEGER .1.3.6.1.4.1.710.3.2.6.4.5.6 |
dot11CurrentPatternThis attribute represents the current pattern that the device is using to determine the hop sequence.rw INTEGER .1.3.6.1.4.1.710.3.2.6.4.5.7 |
dot11MultySupport OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.6.5 |
dot11MultyRateSupportThis attribute indicates the multi cast rate support.rw Enumeration .1.3.6.1.4.1.710.3.2.6.5.1 |
dot11MultyRateDecisionWindowThis attribute indicates the multi cast rate decision window size.rw INTEGER .1.3.6.1.4.1.710.3.2.6.5.2 |
dot11Maintenance OBJECT IDENTIFIER .1.3.6.1.4.1.710.3.2.6.6 |
dot11WaitforAssociationAddressThis attribute indicates the station mac-address. 0 - Use mine 1 - Wait for update via Ethernet Available only for Stations.rw Enumeration .1.3.6.1.4.1.710.3.2.6.6.1 |
dot11JapanCallSignThis attribute indicates the Japan call sign string. Available only for Japan Standard.rw DisplayString .1.3.6.1.4.1.710.3.2.6.6.2 |
breezecomOID OBJECT IDENTIFIER .1.3.6.1.4.1.710.4 |
breezecomAP10 OBJECT IDENTIFIER .1.3.6.1.4.1.710.4.1 |
brzAProamingInA trap indicating that a station has roamed into this AP. It contains the MAC address of the associated station and the device type of that station. NOTIFICATION-TYPE .1.3.6.1.4.1.710.4.1.0.1 |
brzAPassociatedAn AP trap indicating that a new station was associated with this AP. It contains the MAC address of the associated station. NOTIFICATION-TYPE .1.3.6.1.4.1.710.4.1.0.2 |
brzAPdisassociatedAn AP trap indicating that the station dis-associated itself from the AP. The trap contains the MAC address of the disassociated station. NOTIFICATION-TYPE .1.3.6.1.4.1.710.4.1.0.3 |
brzAPagingAn AP trap indicating that the station association was aged out, and removed from that AP. The trap contains the MAC address of the aging station NOTIFICATION-TYPE .1.3.6.1.4.1.710.4.1.0.4 |
brzAProamedOutAn AP trap indicating that a given station has roamed out from this AP. The trap contains the MAC address of the roamed out station NOTIFICATION-TYPE .1.3.6.1.4.1.710.4.1.0.5 |
brzAPWlanStatusapAn AP trap, indicating a change in the Wireless media conditions. An ON value is sent when the Wireless LAN quality drops below the brzWlanTrapThreashold value. A trap with an OFF value is sent if the quality improves, exceeding the brzWlanTrapThreashold value. The Wireless LAN quality value is also being sent. NOTIFICATION-TYPE .1.3.6.1.4.1.710.4.1.0.7 |
brzWlanStatusOfStationAn AP trap, indicating a change in the quality of the Wireless connection, with a specific (associated) station. An ON value indicates a specially bad connection, and an OFF value is sent if the quality improves, exceeding a predetermined threshold value. The brzTrapMacAddress contains the MAC address of the applicable station. NOTIFICATION-TYPE .1.3.6.1.4.1.710.4.1.0.8 |
brzGeneralAPAn AP general purpose trap, for future trap implementation. NOTIFICATION-TYPE .1.3.6.1.4.1.710.4.1.0.9 |
breezecomWB10 OBJECT IDENTIFIER .1.3.6.1.4.1.710.4.2 |
brzWBassociatedA WB trap, indicating that the station became associated-with, or has roamed-to, another AP. The trap contains the MAC address and the average RSSI level of the new AP. If the station was roaming, the MAC address of the old AP, and the RSSI level prior to roaming, is also provided (for an association, the second address will appear as all-zeros). NOTIFICATION-TYPE .1.3.6.1.4.1.710.4.2.0.6 |
brzWBWlanStatusA WB trap, indicating a change in the Wireless media conditions. An ON value is sent when the Wireless LAN quality drops below the brzWlanTrapThreashold value. A trap with an OFF value is sent if the quality improves, exceeding the brzWlanTrapThreashold value. The Wireless LAN quality value is also being sent. NOTIFICATION-TYPE .1.3.6.1.4.1.710.4.2.0.7 |
brzGeneralWBA WB general purpose trap, for future trap implementation. NOTIFICATION-TYPE .1.3.6.1.4.1.710.4.2.0.9 |
breezecomSA10 OBJECT IDENTIFIER .1.3.6.1.4.1.710.4.3 |
brzSTAassociatedA station trap, indicating that the station became associated-with, or has roamed-to, another AP. The trap contains the MAC address and the average RSSI level of the new AP. If the station was roaming, the MAC address of the old AP, and the RSSI level prior to roaming, is also provided (for an association, the second address will appear as all-zeros). NOTIFICATION-TYPE .1.3.6.1.4.1.710.4.3.0.6 |
brzSTAWlanStatusA STA trap, indicating a change in the Wireless media conditions. An ON value is sent when the Wireless LAN quality drops below the brzWlanTrapThreashold value. A trap with an OFF value is sent if the quality improves, exceeding the brzWlanTrapThreashold value. The Wireless LAN quality value is also being sent. NOTIFICATION-TYPE .1.3.6.1.4.1.710.4.3.0.7 |
brzGeneralSTAA STA general purpose trap, for future trap implementation. NOTIFICATION-TYPE .1.3.6.1.4.1.710.4.3.0.9 |
breezecomSA40 OBJECT IDENTIFIER .1.3.6.1.4.1.710.4.4 |
brzSA40associatedA SA-40 trap, indicating that the station became associated-with, or has roamed-to, another AP. The trap contains the MAC address and the average RSSI level of the new AP. If the station was roaming, the MAC address of the old AP, and the RSSI level prior to roaming, is also provided (for an association, the second address will appear as all-zeros). NOTIFICATION-TYPE .1.3.6.1.4.1.710.4.4.0.6 |
brzSA40WlanStatusSA-40 trap, indicating a change in the Wireless media conditions. An ON value is sent when the Wireless LAN quality drops below the brzWlanTrapThreashold value. A trap with an OFF value is sent if the quality improves, exceeding the brzWlanTrapThreashold value. The Wireless LAN quality value is also being sent. NOTIFICATION-TYPE .1.3.6.1.4.1.710.4.4.0.7 |
brzGeneralSA40SA-40 general purpose trap, for future trap implementation. NOTIFICATION-TYPE .1.3.6.1.4.1.710.4.4.0.9 |