BESTPOWER-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for BESTPOWER-MIB.
211
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
211 total| Object Name |
|---|
bestPower OBJECT IDENTIFIER .1.3.6.1.4.1.2947 |
RFC1213-MIB Unknown .1.3.6.1.4.1.2947 |
bestLink OBJECT IDENTIFIER .1.3.6.1.4.1.2947.1 |
upsTrapPowerFailWARNING: Utility power not available. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.1 |
upsTrapPowerRestoredINFORMATION: Utility power has been restored. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.2 |
upsTrapUPSOnBatteryWARNING: The UPS has switched to battery backup power. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.3 |
upsTrapUPSNotOnBatteryINFORMATION: The UPS is not on battery power. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.4 |
upsTrapLowRuntimeSEVERE: The runtime remaining on battery power is very short,
and the UPS will soon shut down. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.5 |
upsTrapUPSCanRunOnBatteryINFORMATION: The UPS has returned from a low runtime
condition. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.6 |
upsTrapNearLowBatterySEVERE: The UPS batteries are low and will soon be exhausted.
If utility power is not restored the UPS will put itself
to 'sleep' and immediately cut power to the load. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.7 |
upsTrapHighBatteryWARNING: The battery charger voltage on the UPS has reached a
value that is too high for safe battery maintenance. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.8 |
upsTrapBatteryOKINFORMATION: The UPS has returned from a near low or high battery
condition. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.9 |
upsTrapLowBatterySEVERE: The UPS will run for approximately 2 minutes more and then
put itself to sleep to prevent a complete discharge of the batteries. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.10 |
upsTrapCheckBatterySEVERE: The UPS has failed a scheduled or manual battery test. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.11 |
upsTrapReplaceBatterySEVERE: One or more UPS batteries need to be replaced. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.12 |
upsTrapCheckInverterSEVERE: The UPS has failed a scheduled or manual inverter test. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.13 |
upsTrapBatteriesDisconnectedWARNING: The UPS battery voltage is either too low or missing to start up. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.14 |
upsTrapOutputOverloadWARNING: The output load exceeds the UPS output capacity. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.15 |
upsTrapUPSNoLongerOverloadedINFORMATION: The UPS has returned from an output overload
condition. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.16 |
upsTrapLowAcOutSEVERE: The output load has exceeded the UPS output capacity, and the UPS has shut down. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.17 |
upsTrapCircuitBreakerWarningSEVERE: To much load equipment has been connected to the UPS and
has has caused excess current draw from the output. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.18 |
upsTrapCircuitBreakerOKINFORMATION: The UPS has returned from a circuit breaker warning
condition. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.19 |
upsTrapCircuitBreakerShdnSEVERE: The UPS has shut down due to an extended excess of current
draw from the output. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.20 |
upsTrapBypassOnSEVERE: The Bypass is presently engaged on the UPS. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.21 |
upsTrapUPSOnlineINFORMATION: The UPS has returned from an on bypass condition. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.22 |
upsTrapSiteWiringFaultSEVERE: The UPS has found a problem in your wall outlet. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.23 |
upsTrapCheckFanSEVERE: The fan on the UPS has stopped . TRAP-TYPE .1.3.6.1.4.1.2947.1.0.24 |
upsTrapHighUPSTempSEVERE: The internal temperature inside the UPS is too hot. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.25 |
upsTrapTempOKINFORMATION: The UPS has returned from a high ambient temp
condition. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.26 |
upsTrapHighHSTempSEVERE: The Inverter heatsink assembly inside the UPS is too hot . TRAP-TYPE .1.3.6.1.4.1.2947.1.0.27 |
upsTrapHSTempOKINFORMATION: The UPS has returned from a high heatsink temp condition. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.28 |
upsTrapHighXFMRTempSEVERE: The temperature of the main transformer inside the UPS is too hot . TRAP-TYPE .1.3.6.1.4.1.2947.1.0.29 |
upsTrapHighPFMTempSEVERE: The temperature of the PFM module inside the UPS is too hot. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.30 |
upsTrapProbeMissingSEVERE: One or all of the temperature probes has been disconnected on the UPS. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.31 |
upsTrapProbeReconnectedINFORMATION: The UPS has returned from a probe missing condition. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.32 |
upsTrapCheckPowerSupplySEVERE: The internal DC supply voltages are attenuated or missing. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.33 |
upsTrapTapRegulatorFaultSEVERE: The UPS detected a possible failure in the tap changer (open or welded relay, etc.) TRAP-TYPE .1.3.6.1.4.1.2947.1.0.34 |
upsTrapRelayFailureSEVERE: There is a hardware problem inside the UPS. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.35 |
upsTrapCheckFuseSEVERE: The failure of one or more fuses has been detected. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.36 |
upsTrapCheckMOVSEVERE: One or more MOVs have failed due to a voltage surge. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.37 |
upsTrapMemoryErrorSEVERE: The UPS has lost the programmed settings in the memory of the logic board. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.38 |
upsTrapCallServiceSEVERE: A hardware malfunction has occurred inside the UPS.
Please consult a factory authorized service representative for assistance. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.39 |
upsTrapManualAlarmBeeperTestInitiatedINFORMATION: A manual test of the alarm beeper is being performed
on the UPS. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.40 |
upsTrapManualAlarmBeeperTestAbortedINFORMATION: The test of UPS has completed. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.41 |
upsTrapScheduledTestInProgressINFORMATION: A test is in progress. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.42 |
upsTrapScheduledTestFailedSEVERE: The last test performed failed. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.43 |
upsTrapCommunicationLostSEVERE: Communication to the UPS has been lost. Steps
to reestablish communication are in progress. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.44 |
upsTrapCommunicationRestoredINFORMATION: Communication with the UPS has been
restored. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.45 |
upsTrapUPSGoingDownWARNING: The ups has been given shutdown command
by the management station. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.46 |
upsTrapUPSTurnedOffINFORMATION: The ups has been turned off
by the management station. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.47 |
upsTrapUPSSleepingINFORMATION: The UPS has entered in 'sleep' mode. Power to the
load has been cut off. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.48 |
upsTrapUPSWokeUpINFORMATION: The UPS woke up from 'sleep' mode. Power to the load has been restored. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.49 |
upsTrapUPSRebootedINFORMATION: The UPS is rebooted. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.50 |
upsTrapEmergencyPowerOFFSEVERE: The Emergency Power OFF feature has been activiated at
the RS-232 port on the UPS. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.51 |
upsTrapHistLogWarnWARNING: The ups history log buffer is almost full. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.52 |
upsTrapEventLogWarnWARNING: The ups event log buffer is almost full. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.53 |
upsTrapUPSFailSEVERE: A critical fault has been detected inside the UPS.
Power to the load has been shut off. TRAP-TYPE .1.3.6.1.4.1.2947.1.0.54 |
upsIdent OBJECT IDENTIFIER .1.3.6.1.4.1.2947.1.1 |
upsIdentUpsNameAn ID string identifying the Family of UPS.ro DisplayString .1.3.6.1.4.1.2947.1.1.1 |
upsIdentModelThe UPS model name (example: 'FE500VA').ro DisplayString .1.3.6.1.4.1.2947.1.1.2 |
upsIdentVARatingThe capacity rating of the UPS expressed in VoltAmperes(VA).ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2947.1.1.3 |
upsIdentUpsTypeType of UPS.ro Enumeration .1.3.6.1.4.1.2947.1.1.4 |
upsIdentUpsSerialNumberA unique identification number provided by the factory.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2947.1.1.5 |
upsIdentUpsIdentificationA string entered by the administrator to provide a unique name for
the UPS.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2947.1.1.6 |
upsIdentFirmwareRevisionThe firmware revision of the UPS.ro DisplayString .1.3.6.1.4.1.2947.1.1.7 |
upsIdentDateOfManufactureThe date when the UPS was manufactured in mm/dd/yyyy format.rw DisplayString .1.3.6.1.4.1.2947.1.1.8 |
upsBattery OBJECT IDENTIFIER .1.3.6.1.4.1.2947.1.2 |
upsBatteryStatusThe status of the inverter .ro Enumeration .1.3.6.1.4.1.2947.1.2.1 |
upsBatteryTimeOnBatteryThe elapsed time in seconds since the UPS has switched to battery power.ro INTEGER .1.3.6.1.4.1.2947.1.2.2 |
upsBatteryRuntimeRemainingThe remaining time in minutes that the UPS will be able to run on battery power.ro INTEGER .1.3.6.1.4.1.2947.1.2.3 |
upsBatteryVoltageThe UPS battery voltage expressed in 1/10 VDC.ro INTEGER .1.3.6.1.4.1.2947.1.2.4 |
upsBatteryCurrentThe battery current expressed in 1/10 ADC.ro INTEGER .1.3.6.1.4.1.2947.1.2.5 |
upsBatteryTemperatureThe internal UPS temperature expressed in 1/10 degree C.ro INTEGER .1.3.6.1.4.1.2947.1.2.6 |
upsBatteryLastReplaceDateThe date when the UPS system's batteries were last replaced
in mm/dd/yyyy format. When the UPS batteries are replaced,
this value should be reset by the administrator.rw DisplayString .1.3.6.1.4.1.2947.1.2.7 |
upsInput OBJECT IDENTIFIER .1.3.6.1.4.1.2947.1.3 |
upsInputPhaseThe AC input phase.ro INTEGER .1.3.6.1.4.1.2947.1.3.1 |
upsInputFrequencyThe utility line frequency in 1/10 Hz.ro INTEGER .1.3.6.1.4.1.2947.1.3.2 |
upsInputVoltageThe utility line voltage in 1/10 VAC.ro INTEGER .1.3.6.1.4.1.2947.1.3.3 |
upsInputCurrentThe utility line current in 1/10 Ampere AC.ro INTEGER .1.3.6.1.4.1.2947.1.3.4 |
upsInputPowerThe utility line power in 1/10 Watts.ro INTEGER .1.3.6.1.4.1.2947.1.3.5 |
upsInputPhase2 OBJECT IDENTIFIER .1.3.6.1.4.1.2947.1.3.6 |
upsInputP2The AC input phase.ro INTEGER .1.3.6.1.4.1.2947.1.3.6.1 |
upsInputFrequency2The utility line frequency in 1/10 Hz.ro INTEGER .1.3.6.1.4.1.2947.1.3.6.2 |
upsInputVoltage2The utility line voltage in 1/10 VAC.ro INTEGER .1.3.6.1.4.1.2947.1.3.6.3 |
upsInputCurrent2The utility line current in 1/10 Ampere AC.ro INTEGER .1.3.6.1.4.1.2947.1.3.6.4 |
upsInputPower2The utility line power in 1/10 Watts.ro INTEGER .1.3.6.1.4.1.2947.1.3.6.5 |
upsInputPhase3 OBJECT IDENTIFIER .1.3.6.1.4.1.2947.1.3.7 |
upsInputP3The AC input phase.ro INTEGER .1.3.6.1.4.1.2947.1.3.7.1 |
upsInputFrequency3The utility line frequency in 1/10 Hz.ro INTEGER .1.3.6.1.4.1.2947.1.3.7.2 |
upsInputVoltage3The utility line voltage in 1/10 VAC.ro INTEGER .1.3.6.1.4.1.2947.1.3.7.3 |
upsInputCurrent3The utility line current in 1/10 Ampere AC.ro INTEGER .1.3.6.1.4.1.2947.1.3.7.4 |
upsInputPower3The utility line power in 1/10 Watts.ro INTEGER .1.3.6.1.4.1.2947.1.3.7.5 |
upsOutput OBJECT IDENTIFIER .1.3.6.1.4.1.2947.1.4 |
upsOutputStatusThe current state of the UPS. If the UPS is unable
to determine its state, this variable is set
to unknown(1).ro Enumeration .1.3.6.1.4.1.2947.1.4.1 |
upsOutputPhaseThe output phase.ro INTEGER .1.3.6.1.4.1.2947.1.4.2 |
upsOutputFrequencyThe output frequency of the UPS expressed in 1/10 Hz.ro INTEGER .1.3.6.1.4.1.2947.1.4.3 |
upsOutputVoltageThe output voltage of the UPS expressed in 1/10 VAC.ro INTEGER .1.3.6.1.4.1.2947.1.4.4 |
upsOutputCurrentThe output current of the UPS expressed in 1/10 AC Amperes.ro NonNegativeInteger .1.3.6.1.4.1.2947.1.4.5 |
upsOutputTruePowerThe true output power of the UPS expressed in 1/10 Watts.ro NonNegativeInteger .1.3.6.1.4.1.2947.1.4.6 |
upsOutputApparentPowerThe apparent output power of the UPS expressed in 1/10 VoltAmperes(VA).ro NonNegativeInteger .1.3.6.1.4.1.2947.1.4.7 |
upsOutputPowerFactorThe output powerfactor of the UPS expressed in +/- 1/10 units deviating
from 1.ro INTEGER .1.3.6.1.4.1.2947.1.4.8 |
upsOutputPercentLoadThe percentage of the total UPS power capacity being used expressed
in % of 100.ro INTEGER -- UNITS percent .1.3.6.1.4.1.2947.1.4.9 |
upsOutputPhase2 OBJECT IDENTIFIER .1.3.6.1.4.1.2947.1.4.10 |
upsOutputP2The output phase.ro INTEGER .1.3.6.1.4.1.2947.1.4.10.1 |
upsOutputFrequency2The output frequency of the UPS expressed in 1/10 Hz.ro INTEGER .1.3.6.1.4.1.2947.1.4.10.2 |
upsOutputVoltage2The output voltage of the UPS expressed in 1/10 VAC.ro INTEGER .1.3.6.1.4.1.2947.1.4.10.3 |
upsOutputCurrent2The output current of the UPS expressed in 1/10 AC Amperes.ro NonNegativeInteger .1.3.6.1.4.1.2947.1.4.10.4 |
upsOutputTruePower2The true output power of the UPS expressed in 1/10 Watts.ro NonNegativeInteger .1.3.6.1.4.1.2947.1.4.10.5 |
upsOutputApparentPower2The apparent output power of the UPS expressed in 1/10 VoltAmperes(VA).ro NonNegativeInteger .1.3.6.1.4.1.2947.1.4.10.6 |
upsOutputPowerFactor2The output powerfactor of the UPS expressed in +\- 1/10 units
deviating from 1.ro INTEGER .1.3.6.1.4.1.2947.1.4.10.7 |
upsOutputPhase3 OBJECT IDENTIFIER .1.3.6.1.4.1.2947.1.4.11 |
upsOutputP3The output phase.ro INTEGER .1.3.6.1.4.1.2947.1.4.11.1 |
upsOutputFrequency3The output frequency of the UPS expressed in 1/10 Hz.ro INTEGER .1.3.6.1.4.1.2947.1.4.11.2 |
upsOutputVoltage3The output voltage of the UPS expressed in 1/10 VAC.ro INTEGER .1.3.6.1.4.1.2947.1.4.11.3 |
upsOutputCurrent3The output current of the UPS expressed in 1/10 AC Amperes.ro NonNegativeInteger .1.3.6.1.4.1.2947.1.4.11.4 |
upsOutputTruePower3The true output power of the UPS expressed in 1/10 Watts.ro NonNegativeInteger .1.3.6.1.4.1.2947.1.4.11.5 |
upsOutputApparentPower3The apparent output power of the UPS expressed in 1/10 VoltAmperes =
(VA).ro NonNegativeInteger .1.3.6.1.4.1.2947.1.4.11.6 |
upsOutputPowerFactor3The output powerfactor of the UPS expressed in +/- 1/10 units deviating
from 1.ro INTEGER .1.3.6.1.4.1.2947.1.4.11.7 |
upsConfig OBJECT IDENTIFIER .1.3.6.1.4.1.2947.1.5 |
upsConfigLowRuntimeSetpointThis setpoint controls when the UPS will initiate a Low Runtime
Alarm.rw INTEGER .1.3.6.1.4.1.2947.1.5.1 |
upsConfigDelayBeforeRestartThe delay in seconds after utility line power returns
before the UPS will turn on. This value is used in
conjunction with TurnUPSOff, RebootUPS, and
the Scheduled Shutdown objects.rw INTEGER .1.3.6.1.4.1.2947.1.5.2 |
upsConfigDelayBeforeShutdownThe delay in seconds that the UPS waits before executing an off
command upon request of an external device.rw INTEGER .1.3.6.1.4.1.2947.1.5.3 |
upsConfigTest OBJECT IDENTIFIER .1.3.6.1.4.1.2947.1.5.4 |
upsConfigTestLevelThis is the level of the System Test.rw Enumeration .1.3.6.1.4.1.2947.1.5.4.1 |
upsConfigDaysBetweenTestsThe number of days between Tests.rw INTEGER .1.3.6.1.4.1.2947.1.5.4.3 |
upsConfigBatteryTestDurationThe number of seconds the UPS must run on battery power during a
battery test.rw INTEGER .1.3.6.1.4.1.2947.1.5.4.4 |
upsConfigScheduleTableThe table to schedule shutting down the ups. SEQUENCE OF UpsConfigScheduleEntry .1.3.6.1.4.1.2947.1.5.5 |
upsConfigScheduleEntryThe entries for each day. UpsConfigScheduleEntry .1.3.6.1.4.1.2947.1.5.5.1 |
upsConfigScheduleIndexThe index of scheduled events.ro INTEGER .1.3.6.1.4.1.2947.1.5.5.1.1 |
upsConfigScheduleShutdownDayThe weekday on which the UPS should shut down.rw Enumeration .1.3.6.1.4.1.2947.1.5.5.1.2 |
upsConfigScheduleShutdownTimeThe time that the process of shutting down the UPS will be initiatedrw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2947.1.5.5.1.3 |
upsConfigScheduleRestartDayThe weekday on which the UPS should restartrw Enumeration .1.3.6.1.4.1.2947.1.5.5.1.4 |
upsConfigScheduleRestartTimeThe time the UPS will restart in hh:mm:ss format.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2947.1.5.5.1.5 |
upsConfigbestLink OBJECT IDENTIFIER .1.3.6.1.4.1.2947.1.5.8 |
bestLinkHistoryLogFrequencyThe frequency of updating the history log in minutes.rw INTEGER .1.3.6.1.4.1.2947.1.5.8.1 |
bestLinkRefreshFrequencyThe frequency of saving configuration,history and event log data
in non-volatile memory. If the value is set to 0, then saving data
is disabled.rw INTEGER .1.3.6.1.4.1.2947.1.5.8.2 |
bestLinkNetIdThe IP address of the device. Setting this parameter causes BestLink to reboot.rw IpAddress .1.3.6.1.4.1.2947.1.5.8.3 |
bestLinkGatewayThe gateway address for the network BestLink is connected to.rw IpAddress .1.3.6.1.4.1.2947.1.5.8.4 |
bestLinkNetMaskThe net mask of the device.rw IpAddress .1.3.6.1.4.1.2947.1.5.8.5 |
bestLinkSysDateThe system date of the device. The date is in mm/dd/yyyy format.
The range of system date is from 1/1/1980 to 12/31/2037.rw DisplayString .1.3.6.1.4.1.2947.1.5.8.6 |
bestLinkSysTimeThe system time of the device. The time is in hh:mm:ss format.rw DisplayString .1.3.6.1.4.1.2947.1.5.8.7 |
bestLinkTftpFileNameThe tftp file name that contains the software upgrade image.rw DisplayString .1.3.6.1.4.1.2947.1.5.8.8 |
bestLinkTftpHostThe tftp host IP address from where to get the image.rw IpAddress .1.3.6.1.4.1.2947.1.5.8.9 |
bestLinkFlashEEPROMSaves the history log, eventlog, and configuration data to non-volatile
memory.rw Enumeration .1.3.6.1.4.1.2947.1.5.8.10 |
bestLinkPrimaryTimeServerThe primary time server is responsible for sending the
correct time to the UPS.rw IpAddress .1.3.6.1.4.1.2947.1.5.8.11 |
bestLinkSecondaryTimeServerThe secondary time server responsible for sending the
correct time to the UPS.rw IpAddress .1.3.6.1.4.1.2947.1.5.8.12 |
bestLinkSoftwareVersionThe version of BestLink software.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2947.1.5.8.13 |
upsConfigTrapsReceivers OBJECT IDENTIFIER .1.3.6.1.4.1.2947.1.5.9 |
upsConfigTrapsReceiversTableA list of managers to send traps to. SEQUENCE OF UpsConfigTrapsReceiversEntry .1.3.6.1.4.1.2947.1.5.9.1 |
upsConfigTrapsReceiversEntryThe managers to send traps to. UpsConfigTrapsReceiversEntry .1.3.6.1.4.1.2947.1.5.9.1.1 |
trapsIndexThe index to a trap receiver entry.ro INTEGER .1.3.6.1.4.1.2947.1.5.9.1.1.1 |
trapsReceiverAddrThe IP address of the manager to send a trap to.rw IpAddress .1.3.6.1.4.1.2947.1.5.9.1.1.2 |
receiverCommunityStringThe community name to use in the trap when
sent to the manager.rw DisplayString .1.3.6.1.4.1.2947.1.5.9.1.1.3 |
severityLevelThe severity threshold of traps to send to the manager.
Traps are labeled by severity as informational(1), warning(2),
severe(3). Only traps of equal or greater severity than
this value are sent to the manager.rw Enumeration .1.3.6.1.4.1.2947.1.5.9.1.1.4 |
receiverAcceptAn entry will become active if yes, otherwise it will be
disabled.rw Enumeration .1.3.6.1.4.1.2947.1.5.9.1.1.5 |
upsConfigRegisteredShutdownClients OBJECT IDENTIFIER .1.3.6.1.4.1.2947.1.5.10 |
upsRegisteredShutdownClientsTableA list of registered shutdown client table entries.
The table contains zero, one, or many rows at any moment,
depending upon the number of Netwatch clients registered
with BestLink SEQUENCE OF UpsRegisteredShutdownClientsEntry .1.3.6.1.4.1.2947.1.5.10.1 |
upsRegisteredShutdownClientsEntryAn entry containing information applicable to a
particular registered shutdown client. UpsRegisteredShutdownClientsEntry .1.3.6.1.4.1.2947.1.5.10.1.1 |
upsRegisteredShutdownClientsIndexAn index of alarm entries in the RegisteredShutdownClientsTable.ro PositiveInteger .1.3.6.1.4.1.2947.1.5.10.1.1.1 |
upsRegisteredShutdownClientsIPAddressThe IP Address of the registered shutdown clientro IpAddress .1.3.6.1.4.1.2947.1.5.10.1.1.2 |
upsRegisteredShutdownClientsTotalNumberOfThe total number of registered shutdown clients.ro INTEGER .1.3.6.1.4.1.2947.1.5.10.2 |
upsControl OBJECT IDENTIFIER .1.3.6.1.4.1.2947.1.6 |
upsControlTurnOffUPSSetting this variable to UpsOff(2) causes the UPS to shut off.
When the UPS is in the off state, the UPS will remain off until
the ON/OFF switch is manually toggled.
Setting this variable to cancelUpsOff(1) allows for a method to cancel
the upsOff(2) command to the UPS that is still pending, or will make
an attempt to restart a UPS that has been shutdown, provided that
BestLink is powered by some other means.
Setting this variable to rebootUps(3) causes the UPS to shut off
and turn back on.
Setting this variable to cancelrebootUps(4) allows for a method to
cancel the rebootUps(3) command to the UPS that is still pending,
or will make an attempt to restart a UPS that has been shutdown,
provided that BestLink is powered by some other means.rw Enumeration .1.3.6.1.4.1.2947.1.6.1 |
upsControlActivateUpsSchedulingSetting this variable to On(2) causes the
UPS to activate the scheduling parameters that have been previously
configured within the upsConfigDailyShutdownScheduleTable and the
upsConfigWeeklyShutdownScheduleTable. Setting this variable to Off(1)
suspends all currently configured schedules.rw Enumeration .1.3.6.1.4.1.2947.1.6.4 |
upsTest OBJECT IDENTIFIER .1.3.6.1.4.1.2947.1.7 |
upsManualTestsSetting this variable to any value other than (1) causes the UPS
to perform a manual test or abort a particular test in progress.rw Enumeration .1.3.6.1.4.1.2947.1.7.1 |
upsAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.2947.1.8 |
upsAlarmsPresentThe present number of active alarm conditions.ro Gauge .1.3.6.1.4.1.2947.1.8.1 |
upsLastKnownAlarmA unique identifier for an alarm condition. This
value must remain constant. Value 'noAlarm(37)'
will be returned if no Alarm has occured till the
point of GET operation.ro Enumeration .1.3.6.1.4.1.2947.1.8.2 |
upsAlarmTableA list of alarm table entries. The table contains
zero, one, or many rows at any moment, depending upon
the number of alarm conditions in effect. The table
is initially empty at agent startup. The agent
creates a row in the table each time a condition is
detected and deletes that row when that condition no
longer pertains. The agent creates the first row with
upsAlarmIndex equal to 1, and increments the value of
upsAlarmIndex each time a new row is created. SEQUENCE OF UpsAlarmEntry .1.3.6.1.4.1.2947.1.8.3 |
upsAlarmEntryAn entry containing information applicable to a
particular alarm. UpsAlarmEntry .1.3.6.1.4.1.2947.1.8.3.1 |
upsAlarmIndexAn index of alarm entries in the alarm log.ro PositiveInteger .1.3.6.1.4.1.2947.1.8.3.1.1 |
upsAlarmNameA unique identifier for an alarm condition. This
value must remain constant.ro Enumeration .1.3.6.1.4.1.2947.1.8.3.1.2 |
upsAlarmTimeThe time that the alarm occurred in hh:mm:ss format.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.2947.1.8.3.1.3 |
upsWellKnownAlarms OBJECT IDENTIFIER .1.3.6.1.4.1.2947.1.8.4 |
upsAlarmOnBatteryThe UPS is drawing power from the batteries.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.1 |
upsAlarmLowRuntimeThe remaining battery runtime is less than or equal
to the upsConfigLowRuntimeSetpoint.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.2 |
upsAlarmNearLowBatteryThe battery voltage on the UPS has reached a value where the inverter will
not be able to function very much longer.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.3 |
upsAlarmLowBatteryThe battery voltage on the UPS has reached a value where the inverter
has stopped providing output power to the connected load equipment.
The UPS has shutdown to protect the batteries from complete discharge.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.4 |
upsAlarmHighBatteryThe battery charger voltage on the UPS has reached a value that
is too high for safe battery maintenance.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.5 |
upsAlarmCheckBatteryThe periodic battery test has failed. A manual test of the batteries
needs to be performed to determine which battery\batteries need
replaced.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.6 |
upsAlarmReplaceBatteryOne or more batteries have been determined to require
replacement. Compatibility: Fortress IIro INTEGER .1.3.6.1.4.1.2947.1.8.4.7 |
upsAlarmCheckInverterThe inverter has failed the automatic system test.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.8 |
upsAlarmBatteriesDisconnectedThe UPS has detected that the DC voltage needed to start up is too
low or missing.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.9 |
upsAlarmOutputOverloadThe output load exceeds the UPS output capacity.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.10 |
upsAlarmLowAcOutThe output load has exceeded the UPS output capacity, and the UPS has shut down.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.11 |
upsAlarmCircuitBreakerWarningTo much load equipment has been connected to the UPS and has has caused excess
current draw from the output.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.12 |
upsAlarmCircuitBreakerShdnThe UPS has shut down due to an extended excess of current draw
from the output.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.13 |
upsAlarmBypassOnThe Bypass is presently engaged on the UPS.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.14 |
upsAlarmAutoBypassThe UPS has gone into the Auto Bypass mode to redirect power around
the UPS circuitry.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.15 |
upsAlarmSiteWiringFaultThe UPS has found a problem in your wall outlet.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.16 |
upsAlarmCheckFanThe fan on the UPS has stoppedro INTEGER .1.3.6.1.4.1.2947.1.8.4.17 |
upsAlarmHighAmbTempThe internal temperature inside the UPS is too hot.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.18 |
upsAlarmHighHSTempThe Inverter heatsink assembly inside the UPS is to hot .ro INTEGER .1.3.6.1.4.1.2947.1.8.4.19 |
upsAlarmHighXFMRTempThe temperature of the main transformer inside the UPS is too hot .ro INTEGER .1.3.6.1.4.1.2947.1.8.4.20 |
upsAlarmHighPFMTempThe temperature of the PFM module inside the UPS is too hot .ro INTEGER .1.3.6.1.4.1.2947.1.8.4.21 |
upsAlarmProbeMissingOne or all of the sense probes has been disconnected on the UPS.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.22 |
upsAlarmCheckPowerSupplyThe internal DC supply voltages are attenuated or missing.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.23 |
upsAlarmTapRegulatorThe UPS detected a possible failure in the tap changer (open or
welded relay, etc.)ro INTEGER .1.3.6.1.4.1.2947.1.8.4.24 |
upsAlarmRelayFailureThere is a hardware problem inside the UPS.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.25 |
upsAlarmCheckFuseThe failure of one or more fuses has been detected.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.26 |
upsAlarmCheckMOVOne or more MOVs have failed due to a voltage surge.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.27 |
upsAlarmMemoryErrorThe UPS has lost the programmed settings in the memory of the logic
board.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.28 |
upsAlarmCallServiceA hardware malfunction has occurred inside the UPS. Please consult a
factory authorized service representative for assistance.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.29 |
upsAlarmupsFailedA general fault in the UPS has been detected.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.30 |
upsAlarmUserTestA user test of the alarm beeper is in progress.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.31 |
upsAlarmTestInProgressA test is in progress.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.32 |
upsAlarmDiagnosticTestFailedThe result of the last diagnostic test indicates a failure.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.33 |
upsAlarmEPOThe Emergency Power OFF feature has been activiated at the RS-232
port on the UPS.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.34 |
upsAlarmUpsOffThe output of the UPS is in the off state.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.35 |
upsAlarmCommunicationsLostA problem has been encountered in the
communications between the agent and the UPS.ro INTEGER .1.3.6.1.4.1.2947.1.8.4.36 |