BENU-CHASSIS-MIB
AI MIB Summary
The BENU-CHASSIS-MIB provides SNMP-based monitoring and management of physical chassis components, including power supplies, fans, and temperature sensors, for Benu Networks hardware. It enables systems administrators to track hardware health status and environmental conditions to detect failures or degradation in network infrastructure.
Initial creation MIB module for Benu Networks Chassis. Copyright (C) 2001, 2008 by Benu Networks, Inc. All rights reserved.
Main OID:
benuChassisMIB.1.3.6.1.4.1.39406.1.1
83
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
83 total| Object Name |
|---|
benuChassisMIBInitial creation MIB module for Benu Networks Chassis. Copyright (C) 2001, 2008 by Benu Networks, Inc. All rights reserved. MODULE-IDENTITY .1.3.6.1.4.1.39406.1.1 |
benuChassisNotifObjects OBJECT IDENTIFIER .1.3.6.1.4.1.39406.1.1.0 |
benuChassisPowerFailureA chassisPowerFailureTrap is generated when a Power Failure is detected in the systemobsolete NOTIFICATION-TYPE .1.3.6.1.4.1.39406.1.1.0.1 |
benuChassisFanFailureTrapA chassisFanFailureTrap is generated when a Fan Failure is detected in the system NOTIFICATION-TYPE .1.3.6.1.4.1.39406.1.1.0.2 |
benuLinkUpTrapA proprietary Link Up Notification for all interfaces. This notification contains more details than the standard 'linkUp' notification in RFC 2863. NOTIFICATION-TYPE .1.3.6.1.4.1.39406.1.1.0.3 |
benuLinkDownTrapA proprietary Link Down Notification for all interfaces. This notification contains more details than the standard 'linkDown' notification in RFC 2863. NOTIFICATION-TYPE .1.3.6.1.4.1.39406.1.1.0.4 |
benuSensorCriticalThis notification signifies the transition of the sensor state from normal to critical. NOTIFICATION-TYPE .1.3.6.1.4.1.39406.1.1.0.5 |
benuSensorNormalThis notification signifies the transition of the sensor state from critical to normal. NOTIFICATION-TYPE .1.3.6.1.4.1.39406.1.1.0.6 |
benuChassisPowerFaultA chassisPowerFaultTrap is generated when a Power Failure is detected in the system NOTIFICATION-TYPE .1.3.6.1.4.1.39406.1.1.0.7 |
benuChassisPowerRecoveryA chassisPowerRecoveryTrap is generated when a failed Power supply recovery is detected in the system NOTIFICATION-TYPE .1.3.6.1.4.1.39406.1.1.0.8 |
benuChassisPowerPresentA chassisPowerPresentTrap is generated when a redundant Power supply is inserted in the system NOTIFICATION-TYPE .1.3.6.1.4.1.39406.1.1.0.9 |
benuChassisPowerAbsentA chassisPowerAbsentTrap is generated when a redundant Power supply is removed from the system NOTIFICATION-TYPE .1.3.6.1.4.1.39406.1.1.0.10 |
benuChassisMIBObjects OBJECT IDENTIFIER .1.3.6.1.4.1.39406.1.1.1 |
benuChassisInfo OBJECT IDENTIFIER .1.3.6.1.4.1.39406.1.1.1.1 |
benuChassisTypeChassis type.ro Enumeration .1.3.6.1.4.1.39406.1.1.1.1.1 |
benuChassisHwVersionChassis hardware revision level, or an empty string if unavailable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.39406.1.1.1.1.2 |
benuChassisIdUnique ID string. Defaults to chassis serial number if available, otherwise emptyro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.39406.1.1.1.1.3 |
benuChassisNumOfSlotsNumber of slots in this chassis, or -1 if neither applicable nor determinable.ro Integer32 .1.3.6.1.4.1.39406.1.1.1.1.4 |
benuChassisPowerTrapEnableThis object controls SNMP traps for chassis Power Failure. If its value is set to enabled(1), then traps are generated. If the value is disabled(2), then traps are not generated. By default, this object has the value enabled(1).rw Enumeration .1.3.6.1.4.1.39406.1.1.1.1.5 |
benuChassisFanTrapEnableThis object controls SNMP traps for chassis Fan Failure. If its value is set to enabled(1), then traps are generated. If the value is disabled(2), then traps are not generated. By default, this object has the value enabled(1).rw Enumeration .1.3.6.1.4.1.39406.1.1.1.1.6 |
benuChassisSensorTrapEnableThis object controls SNMP traps for chassis senor Failure. If its value is set to enabled(1), then traps are generated. If the value is disabled(2), then traps are not generated. By default, this object has the value enabled(1).rw Enumeration .1.3.6.1.4.1.39406.1.1.1.1.7 |
benuSysUpTimeAtLastChassisChangeTime (in hundredths of a second) from the last cold start to the last change in the chassis' configuration. This value will be updated whenever the chassis experiences a change in the count, type, or slot position of a card in cardTable.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.39406.1.1.1.1.8 |
benuCardInfo OBJECT IDENTIFIER .1.3.6.1.4.1.39406.1.1.1.2 |
benuCardTableChassis card table. SEQUENCE OF BenuCardEntry .1.3.6.1.4.1.39406.1.1.1.2.1 |
benuCardEntryChassis card table. BenuCardEntry .1.3.6.1.4.1.39406.1.1.1.2.1.1 |
benuCardIndexIndex into cardTable (not physical chassis slot number). Unsigned32 .1.3.6.1.4.1.39406.1.1.1.2.1.1.1 |
benuCardTypeFunctional type of this card.ro Enumeration .1.3.6.1.4.1.39406.1.1.1.2.1.1.2 |
benuCardDescrText description of this card.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.39406.1.1.1.2.1.1.3 |
benuCardSerialThe serial number of this card, or zero if unavailable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.39406.1.1.1.2.1.1.4 |
benuCardPartNumberThe part number of this card, or an empty string if unavailable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.39406.1.1.1.2.1.1.5 |
benuCardHwVersionHardware revision level of this card, or an empty string if unavailable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.39406.1.1.1.2.1.1.6 |
benuCardSwVersionVersion of the firmware or microcode installed on this card, or an empty string if unavailable.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.39406.1.1.1.2.1.1.7 |
benuCardSlotNumberSlot number relative to the containing card or chassis, or -1 if neither applicable nor determinable.ro Integer32 .1.3.6.1.4.1.39406.1.1.1.2.1.1.8 |
benuCardRamSizeNumber of kilobytes of DRAM. A value -1 means not available / not applicable A value 0 means internal error.ro Integer32 .1.3.6.1.4.1.39406.1.1.1.2.1.1.9 |
benuCardPrimaryDiskSizeNumber of kilobytes of Disk Memory (SATA or Hard Disk). A value -1 means not available / not applicable. A value 0 means internal error.ro Integer32 .1.3.6.1.4.1.39406.1.1.1.2.1.1.10 |
benuCardSecondaryDiskSizeNumber of kilobytes of Disk Memory (SATA or Hard Disk). A value -1 means not available / not applicable. A value 0 means internal error.ro Integer32 .1.3.6.1.4.1.39406.1.1.1.2.1.1.11 |
benuCardOperStatusThe operational status of the card. cardOperStatus is up when a card is recognized by the device and is enabled for operation. cardOperStatus is down if the card is not recognized by the device, or if it is not enabled for operation. cardOperStatus is standby if the card is enabled and acting as a standby slave. Intermediate stages (rom,flash,diag,boot,config) are also exposed.ro Enumeration .1.3.6.1.4.1.39406.1.1.1.2.1.1.12 |
benuCardIfInfo OBJECT IDENTIFIER .1.3.6.1.4.1.39406.1.1.1.3 |
benuCardIfIndexTableChassis card Interface table. SEQUENCE OF BenuCardIfIndexEntry .1.3.6.1.4.1.39406.1.1.1.3.1 |
benuCardIfIndexEntryChassis card table. BenuCardIfIndexEntry .1.3.6.1.4.1.39406.1.1.1.3.1.1 |
benuCardIfIndexmatches RFC1213 ifTable IfIndex Unsigned32 .1.3.6.1.4.1.39406.1.1.1.3.1.1.1 |
benuCardIfNamematches RFC1213 ifXTable IfNamero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.39406.1.1.1.3.1.1.2 |
benuCardIfPortNumberChassis port number, unique per port on a given card if available.ro Integer32 .1.3.6.1.4.1.39406.1.1.1.3.1.1.3 |
benuCardIfSlotNumberPhysical slot number of the card in the Chassis which contains this interfacero Integer32 .1.3.6.1.4.1.39406.1.1.1.3.1.1.4 |
benuCardIfLinkUpDownEnableThis enables and disables the sending of the proprietary notifications 'benuLinkUpTrap' and 'benuLinkDownTrap' that provide more information than the standard link up and link down notifications. By default, these traps are disabled.rw Enumeration .1.3.6.1.4.1.39406.1.1.1.3.1.1.5 |
benuCardIfPortTypeThis object is used to identify port types for a given card.ro Enumeration .1.3.6.1.4.1.39406.1.1.1.3.1.1.6 |
benuCardIfBindNameinterface name which is bound to this port . This string will be empty if there is no interface bind to this portro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.39406.1.1.1.3.1.1.7 |
benuCardIfEncapsulationThe encapsulation method used by the port.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.39406.1.1.1.3.1.1.8 |
benuCardIfVirtualTypeThis object is used to identify virtualized interfaces.ro Enumeration .1.3.6.1.4.1.39406.1.1.1.3.1.1.9 |
benuSensorInfo OBJECT IDENTIFIER .1.3.6.1.4.1.39406.1.1.1.4 |
benuSensorTableChassis card table. SEQUENCE OF BenuSensorEntry .1.3.6.1.4.1.39406.1.1.1.4.1 |
benuSensorEntryChassis card table. BenuSensorEntry .1.3.6.1.4.1.39406.1.1.1.4.1.1 |
benuSensorCardIndexcardIndex of the card in the Chassis cardTable which contains this sensor. Unsigned32 .1.3.6.1.4.1.39406.1.1.1.4.1.1.1 |
benuSensorIndexIndex into sensorTable. Unsigned32 .1.3.6.1.4.1.39406.1.1.1.4.1.1.2 |
benuSensorNameName of the sensor.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.39406.1.1.1.4.1.1.3 |
benuSensorTypeType of the sensor.ro Enumeration .1.3.6.1.4.1.39406.1.1.1.4.1.1.4 |
benuSensorValueCurrent Value of this sensor. The unit types for different type of sensors: temparature -- celcius Fan -- rpm Volatage -- volts Electric Current -- amperes Power -- wattsro Integer32 .1.3.6.1.4.1.39406.1.1.1.4.1.1.5 |
benuSensorMinThreshMinimum threshold for this sensor.ro Integer32 .1.3.6.1.4.1.39406.1.1.1.4.1.1.6 |
benuSensorMaxThreshMaximum threshold for this sensor.ro Integer32 .1.3.6.1.4.1.39406.1.1.1.4.1.1.7 |
benuSensorStateState of the sensor.ro Enumeration .1.3.6.1.4.1.39406.1.1.1.4.1.1.8 |
benuSensorIdUnique ID of the sensor.ro Integer32 .1.3.6.1.4.1.39406.1.1.1.4.1.1.9 |
benuChassisGeneralInfo OBJECT IDENTIFIER .1.3.6.1.4.1.39406.1.1.1.5 |
benuSysUpTimeSinceLastConfigChangeThe time (in hundredths of a second) since the last configuration change in the system.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.39406.1.1.1.5.1 |
benuFanInfo OBJECT IDENTIFIER .1.3.6.1.4.1.39406.1.1.1.6 |
benuFanTableChassis Fan table. SEQUENCE OF BenuFanEntry .1.3.6.1.4.1.39406.1.1.1.6.1 |
benuFanEntryChassis card table. BenuFanEntry .1.3.6.1.4.1.39406.1.1.1.6.1.1 |
benuFanCardIndexcardIndex of the card in the Chassis cardTable which contains this Fan. Unsigned32 .1.3.6.1.4.1.39406.1.1.1.6.1.1.1 |
benuFanMaxSpeedMaximum expected speed of each Fan. This value is applicable to all Fans in the card. Units : The value range is from 0 to 100ro Unsigned32 .1.3.6.1.4.1.39406.1.1.1.6.1.1.2 |
benuFanCurSpeedCurrent speed of each Fan. This value is applicable to all Fans in the card. Units : The value range is from 0 to 100 and is less than or equal to benuFanMaxSpeedro Unsigned32 .1.3.6.1.4.1.39406.1.1.1.6.1.1.3 |
benuFanStatusA value of -1 means Not available / Not applicable. The lower order 7 bits indicates status of 7 Fans. A bit value of one indicates FAN is non-operational. A bit value of zero indicates FAN is operational. Examples : (a) Value of 1 ( 0000 0001 ) indicates FAN #1 is non-operational. (b) Value of 9 ( 0000 1001 ) indicates FAN #1 and FAN #4 are non-operational. (c) Value of 73( 0100 1001 ) indicates FAN #1,FAN #4 and FAN #7 are non-operational.ro Integer32 .1.3.6.1.4.1.39406.1.1.1.6.1.1.4 |
benuPowerSupplyInfo OBJECT IDENTIFIER .1.3.6.1.4.1.39406.1.1.1.7 |
benuPowerSupplyTableBenu power supply state information. SEQUENCE OF BenuPowerSupplyEntry .1.3.6.1.4.1.39406.1.1.1.7.1 |
benuPowerSupplyEntryPower supply table. BenuPowerSupplyEntry .1.3.6.1.4.1.39406.1.1.1.7.1.1 |
benuPowerSupplyIndexThis object is used to identify the power supply. Enumeration .1.3.6.1.4.1.39406.1.1.1.7.1.1.1 |
benuPowerSupplyNameThe name of the power supply.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.39406.1.1.1.7.1.1.2 |
benuPowerSupplyPresentIndicates whether or not the power supply is installed in the chassis.ro Enumeration .1.3.6.1.4.1.39406.1.1.1.7.1.1.3 |
benuPowerSupplyTypeIndicates the type of the power supply.ro Enumeration .1.3.6.1.4.1.39406.1.1.1.7.1.1.4 |
benuPowerSupplyPoweredIndicates whether or not the power supply is actively supplying power. The value of notApplicable(3) will show if the entry for benuPowerSupplyPresent is no(2).ro Enumeration .1.3.6.1.4.1.39406.1.1.1.7.1.1.5 |
benuChassisNotifVariables OBJECT IDENTIFIER .1.3.6.1.4.1.39406.1.1.2 |
benuChassisPowerFailureInfoIndicates the location of the Power Failure.roobsolete Enumeration .1.3.6.1.4.1.39406.1.1.2.1 |
benuChassisFanFailureInfoIndicates the location of the Fan Failure.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.39406.1.1.2.2 |
benuChassisPowerFailureCardInfoIndicates the Card Index Card Index starts from #1.roobsolete Unsigned32 .1.3.6.1.4.1.39406.1.1.2.3 |
benuChassisPowerInfoIndicates the location of the Power Failure or recovery.ro Enumeration .1.3.6.1.4.1.39406.1.1.2.4 |