ATS-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for ATS-MIB.
165
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
165 total| Object Name |
|---|
ats OBJECT IDENTIFIER .1.3.6.1.4.1.37662 |
RFC1155-SMI Unknown .1.3.6.1.4.1.37662 |
product OBJECT IDENTIFIER .1.3.6.1.4.1.37662.1 |
webAppliance OBJECT IDENTIFIER .1.3.6.1.4.1.37662.1.2 |
atsAgent OBJECT IDENTIFIER .1.3.6.1.4.1.37662.1.2.2 |
single OBJECT IDENTIFIER .1.3.6.1.4.1.37662.1.2.2.1 |
atsObjectGroup OBJECT IDENTIFIER .1.3.6.1.4.1.37662.1.2.2.1.1 |
atsIdentGroup OBJECT IDENTIFIER .1.3.6.1.4.1.37662.1.2.2.1.1.1 |
atsIdentGroupModelThe device model name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.37662.1.2.2.1.1.1.1 |
atsIdentGroupSerialNumberThe device serial number.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.37662.1.2.2.1.1.1.2 |
atsIdentGroupManufacturerThe device manufacturer name.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.37662.1.2.2.1.1.1.3 |
atsIdentGroupFirmwareRevisionThe device firmware revision.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.37662.1.2.2.1.1.1.4 |
atsIdentGroupAgentFirmwareRevisionThe agent firmware revision.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.37662.1.2.2.1.1.1.5 |
atsInputGroup OBJECT IDENTIFIER .1.3.6.1.4.1.37662.1.2.2.1.1.2 |
atsInputGroupPreferenceThis shows the Output Source Priority by Source A or Source B.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.37662.1.2.2.1.1.2.1 |
atsInputGroupSourceAstatusThis field shows the status of the source A. Status included? 'OK','Fail'. 'OK' mean frequency and voltage of Source A are normal.ro Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.2.2 |
atsInputGroupSourceAinputVoltageThe source A input voltage of the ATS input in volts.ro INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.2.3 |
atsInputGroupSourceAinputFrequencyThe source A input frequency of the ATS input in 0.1 Hz.ro INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.2.4 |
atsInputGroupSourceBstatusThis field shows the status of the source B. Status included? 'OK','Fail'. 'OK' mean frequency and voltage of Source B are normal.ro Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.2.5 |
atsInputGroupSourceBinputVoltageThe source B input voltage of the ATS input in volts.ro INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.2.6 |
atsInputGroupSourceBinputFrequencyThe source B input frequency of the ATS input in 0.1 Hz.ro INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.2.7 |
atsInputGroupSourceAvoltageUpperLimitThe source A voltage upper limit of the ATS input in volts.ro INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.2.8 |
atsInputGroupSourceAvoltageLowerLimitThe source A voltage lower limit of the ATS input in volts.ro INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.2.9 |
atsInputGroupSourceAfrequencyUpperLimitThe source A frequency upper limit of the ATS input in 0.1 Hz.ro INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.2.10 |
atsInputGroupSourceAfrequencyLowerLimitThe source A frequency lower limit of the ATS input in 0.1 Hz.ro INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.2.11 |
atsInputGroupSourceBvoltageUpperLimitThe source B voltage upper limit of the ATS input in volts.ro INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.2.12 |
atsInputGroupSourceBvoltageLowerLimitThe source B voltage lower limit of the ATS input in volts.ro INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.2.13 |
atsInputGroupSourceBfrequencyUpperLimitThe source B frequency upper limit of the ATS input in 0.1 Hz.ro INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.2.14 |
atsInputGroupSourceBfrequencyLowerLimitThe source B frequency lower limit of the ATS input in 0.1 Hz.ro INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.2.15 |
atsOutputGroup OBJECT IDENTIFIER .1.3.6.1.4.1.37662.1.2.2.1.1.3 |
atsOutputGroupOutputSourceOutput source is supply by Source A or Source B. Status included? 'Source A','Source B'.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.37662.1.2.2.1.1.3.1 |
atsOutputGroupOutputVoltageThe Output Voltage in volts.ro NonNegativeInteger (UPS-MIB) .1.3.6.1.4.1.37662.1.2.2.1.1.3.2 |
atsOutputGroupOutputFequencyThe output fequency in 0.1 Hz.ro NonNegativeInteger (UPS-MIB) .1.3.6.1.4.1.37662.1.2.2.1.1.3.3 |
atsOutputGroupOutputCurrentThe output current in 0.1 A.ro NonNegativeInteger (UPS-MIB) .1.3.6.1.4.1.37662.1.2.2.1.1.3.4 |
atsOutputGroupLoadThe load in %.ro NonNegativeInteger (UPS-MIB) .1.3.6.1.4.1.37662.1.2.2.1.1.3.5 |
atsHmiSwitchGroup OBJECT IDENTIFIER .1.3.6.1.4.1.37662.1.2.2.1.1.4 |
atsHmiSwitchGroupBuzzerThis field shows the status of the buzzer. Status included? 'Enable','Disable'.ro Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.4.1 |
atsHmiSwitchGroupAtsAlarmThis shows the alarm occured.ro Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.4.2 |
atsHmiSwitchGroupAutoReturnAuto recover to that setting value when two input source normal.ro Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.4.3 |
atsHmiSwitchGroupSourceTransferByLoadOn: If overload timeout occurred , ATS will tranfer to another source automaticlly. Off:If overload timeout occurred , ATS will turn off the output source.ro Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.4.4 |
atsHmiSwitchGroupSourceTransferByPhaseOn: when the transfer of output source occur, the transfer can active if differernce of phase less than setting value Off: Switch transfer immed... whatever difference of phase.ro Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.4.5 |
atsMiscellaneousGroup OBJECT IDENTIFIER .1.3.6.1.4.1.37662.1.2.2.1.1.5 |
atsMiscellaneousGroupAtsSystemTempertureThe ATS system temperture in degree C.ro INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.5.1 |
atsMiscellaneousGroupSystemMaxCurrentThe system max current int 0.1 Amp.ro INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.5.2 |
atsControlGroup OBJECT IDENTIFIER .1.3.6.1.4.1.37662.1.2.2.1.1.6 |
atsControlGroupBuzzerAlarmControlThe buzzer alarm control.rw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.6.1 |
atsControlGroupManualTransferUser can click this bottom to decide output source supply is Source A or Source B.rw INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.6.2 |
agentConfig OBJECT IDENTIFIER .1.3.6.1.4.1.37662.1.2.2.1.1.7 |
agentConfigIpaddressThe ip address that NMS can identify the managed
devicerw IpAddress .1.3.6.1.4.1.37662.1.2.2.1.1.7.1 |
agentConfigGatewayThe default gateway that allow device managed
through routersrw IpAddress .1.3.6.1.4.1.37662.1.2.2.1.1.7.2 |
agentConfigSubnetMaskInternet address subnet maskrw IpAddress .1.3.6.1.4.1.37662.1.2.2.1.1.7.3 |
agentConfigDateThe date in agent, format is (dd/mm/yyyy)rw DisplayString .1.3.6.1.4.1.37662.1.2.2.1.1.7.4 |
agentConfigTimeThe time in agent, format is (hh:mm:ss)rw DisplayString .1.3.6.1.4.1.37662.1.2.2.1.1.7.5 |
agentConfigHistoryLogFrequencyThe frequency of the updation of the history log. The value
is in secondsrw INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.7.6 |
agentConfigExtHistoryLogFrequencyThe ups parameters are sampled at the rate governed by the
mconfigHistroyLogFrequency. These sampled values are further
conslidated over period of time which is determined by this
object.rw INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.7.7 |
agentConfigPollRateThe frequency that proxy agent polls the connected
UPS in JBUS protocol. (unit : second)rw INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.7.8 |
agentConfigBaudRateThe serial port communication speed. only 9600 allowedro INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.7.9 |
agentConfigDhcpStatueEnable or disable DHCP/BootP capabilityrw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.7.10 |
agentConfigTelnetStatueEnable or disable telnet accessrw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.7.11 |
agentConfigTftpStatueEnable or disable network upgrade capabilityrw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.7.12 |
agentConfigResetToDefaultReset all parameters of ATS to default valuerw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.7.13 |
agentConfigRestartRestart ATSrw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.7.14 |
agentConfigClearAgentLogClear agent log datarw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.7.15 |
agentConfigClearEventLogClear event log datarw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.7.16 |
agentConfigClearExtHistoryLogClear extented history log datarw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.7.17 |
agentConfigClearHistoryLogClear history log datarw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.7.18 |
agentConfigTrapRetryCountThe count of repeat traps to send to NMS before trap
acknowledge received.rw INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.7.19 |
agentConfigTrapRetryTimeThe time between retry traps sned to NMS.rw INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.7.20 |
agentConfigTrapAckSignatureThe signature of trap acknowledge.rw INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.7.21 |
agentConfigMibVersionThe version of MIB spec.ro INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.7.22 |
agentConfigTrapsReceiversTableA list of managers to send traps to. The number of
entries is given by the value of agentConfigNumTrapReceivers SEQUENCE OF AgentConfigTrapsReceiversEntry .1.3.6.1.4.1.37662.1.2.2.1.1.7.23 |
agentConfigTrapsReceiversEntryThe managers to send traps to. AgentConfigTrapsReceiversEntry .1.3.6.1.4.1.37662.1.2.2.1.1.7.23.1 |
trapsIndexThe index to a trap receiver entry.ro INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.7.23.1.1 |
trapsReceiverAddrThe IP address of the manager to send a trap to.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.37662.1.2.2.1.1.7.23.1.2 |
receiverCommunityStringThe community name to use in the trap when
sent to the manager.rw DisplayString .1.3.6.1.4.1.37662.1.2.2.1.1.7.23.1.3 |
receiverNmsTypeThe trap group that NMS desired.rw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.7.23.1.4 |
receiverSeverityLevelThe severity level of traps to be received by this manager.rw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.7.23.1.5 |
receiverDescriptionDescription of trap receiversrw DisplayString .1.3.6.1.4.1.37662.1.2.2.1.1.7.23.1.6 |
agentConfigAccessControlTableA list of managers which can access ATS with private
community string. SEQUENCE OF AgentConfigAccessControlEntry .1.3.6.1.4.1.37662.1.2.2.1.1.7.24 |
agentConfigAccessControlEntryThe managers. AgentConfigAccessControlEntry .1.3.6.1.4.1.37662.1.2.2.1.1.7.24.1 |
accessIndexThe index to a access control entry.ro INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.7.24.1.1 |
accessControlAddrThe IP address of the manager to access ATSrw IpAddress .1.3.6.1.4.1.37662.1.2.2.1.1.7.24.1.2 |
accessCommunityStringThe community name to use in the manager when
access ATSrw DisplayString .1.3.6.1.4.1.37662.1.2.2.1.1.7.24.1.3 |
accessControlModeAccess type, only read/Write access type can change parameter
of ATSrw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.7.24.1.4 |
agentConfigDefaultLanguageThe default languauge for browser, when set to auto(1)
ATS will send page in the language depends on the
request language of browser.rw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.7.25 |
agentConfigIPv6AddrStatusThe status of IPv6 global address. When the auto-configuration
of IPv6 address is disabled, it shows manual configuration(3).
Otherwise, it shows valid(2) for auto-configured successfully,
or shows invalid(1) for the failure in auto-configured.ro Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.7.26 |
agentConfigIPv6AddrAutoConfigThe state of IPv6 address auto-configuration. If set to enable(1),
ATS will try to get a valid global/site-local address from IPv6
router or DHCPv6 server on the same link.rw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.7.27 |
agentConfigIPv6LinkLocalAddrThe IPv6 link-local address of ATS. It is auto-configured based on
MAC address of ATS.ro DisplayString .1.3.6.1.4.1.37662.1.2.2.1.1.7.28 |
agentConfigIPv6GlobalAddrThe IPv6 global/site-local address of ATS. If change it manually,
the agentConfigIPv6AddrStatus and agentConfigIPv6AddrAutoConfig will
be changed to manual configuration and disabled respectively.rw DisplayString .1.3.6.1.4.1.37662.1.2.2.1.1.7.29 |
agentConfigIPv6PrefixlLengthThe prefix length of IPv6 global/site-local address.If change it manually,
the agentConfigIPv6AddrStatus and agentConfigIPv6AddrAutoConfig will
be changed to manual configuration and disabled respectively.rw INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.7.30 |
agentConfigIPv6DefaultRouterThe address of IPv6 default router. If change it manually,
the agentConfigIPv6AddrStatus and agentConfigIPv6AddrAutoConfig will
be changed to manual configuration and disabled respectively.rw DisplayString .1.3.6.1.4.1.37662.1.2.2.1.1.7.31 |
emdStatus OBJECT IDENTIFIER .1.3.6.1.4.1.37662.1.2.2.1.1.8 |
emdSatatusEmdTypeThe type of EMD plugged into the port.ro Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.8.1 |
emdSatatusTemperatureThe measurement of EMD temperature, in 0.1 degreero INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.8.2 |
emdSatatusHumidityThe measurement of EMD humidity, in 0.1 degreero INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.8.3 |
emdSatatusAlarm1The EMD alarm-1 statusro Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.8.4 |
emdSatatusAlarm2The EMD alarm-2 statusro Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.8.5 |
emdConfig OBJECT IDENTIFIER .1.3.6.1.4.1.37662.1.2.2.1.1.9 |
usahEmdConfigEmdConfigEnable or disable to detect presence of EMDrw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.9.1 |
emdConfigEmdNameDescription of EMDrw DisplayString .1.3.6.1.4.1.37662.1.2.2.1.1.9.2 |
emdConfigTemperature OBJECT IDENTIFIER .1.3.6.1.4.1.37662.1.2.2.1.1.9.3 |
emdConfigTempNameDescription of EMD temperature sensorrw DisplayString .1.3.6.1.4.1.37662.1.2.2.1.1.9.3.1 |
emdConfigTempHighSetPointThe set point for high temperature warning, in degreesrw INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.9.3.2 |
emdConfigTempHighStatusTo enable/disable high set point check with emd temperature.rw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.9.3.3 |
emdConfigTempLowSetPointThe set point for low temperature warning, in degreesrw INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.9.3.4 |
emdConfigTempLowStatusTo enable/disable low set point check with emd temperature.rw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.9.3.5 |
emdConfigTempOffsetThe offset to calibrate temperature of EMD, in degreesrw INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.9.3.6 |
emdConfigHumidity OBJECT IDENTIFIER .1.3.6.1.4.1.37662.1.2.2.1.1.9.4 |
emdConfigHumidityNameDescription of EMD humidity sensorrw DisplayString .1.3.6.1.4.1.37662.1.2.2.1.1.9.4.1 |
emdConfigHumidityHighSetPointThe set point for high humidity warning, in %rw INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.9.4.2 |
emdConfigHumidityHighStatusTo enable/disable high set point check with emd humidity.rw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.9.4.3 |
emdConfigHumidityLowSetPointThe set point for low humidity warning, in %rw INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.9.4.4 |
emdConfigHumidityLowStatusTo enable/disable low set point check with emd humidity.rw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.9.4.5 |
emdConfigHumidityOffsetThe offset to calibrate humidity of EMD, in %rw INTEGER .1.3.6.1.4.1.37662.1.2.2.1.1.9.4.6 |
emdConfigAlarm1 OBJECT IDENTIFIER .1.3.6.1.4.1.37662.1.2.2.1.1.9.5 |
emdConfigAlarm1NameDescription of EMD alarm-1rw DisplayString .1.3.6.1.4.1.37662.1.2.2.1.1.9.5.1 |
emdConfigAlarm1TypeThe alarm-1 operation typerw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.9.5.2 |
emdConfigAlarm2 OBJECT IDENTIFIER .1.3.6.1.4.1.37662.1.2.2.1.1.9.6 |
emdConfigAlarm2NameDescription of EMD alarm-2rw DisplayString .1.3.6.1.4.1.37662.1.2.2.1.1.9.6.1 |
emdConfigAlarm2TypeThe alarm-1 operation typerw Enumeration .1.3.6.1.4.1.37662.1.2.2.1.1.9.6.2 |
atsTrapGroup OBJECT IDENTIFIER .1.3.6.1.4.1.37662.1.2.2.1.2 |
atsAtsAlarmWARNING: ATS Alarm. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.1 |
atsSourceAvoltageAbnormalWARNING: Source A voltage abnormal. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.2 |
atsSourceBvoltageAbnormalWARNING: Source B voltage abnormal. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.3 |
atsSourceAfrequencyAbnormalWARNING: Source A frequency abnormal. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.4 |
atsSourceBfrequencyAbnormalWARNING: Source B frequency abnormal. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.5 |
atsOutputOverLoadSEVERE: Output over load. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.6 |
atsWorkPowerAabnormalSEVERE: Unit fault (Working power A abnormal). TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.7 |
atsWorkPowerBabnormalSEVERE: Unit fault (Working power B abnormal). TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.8 |
atsOverTemperatureWARNING: Cabinet over temperature. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.9 |
atsDcOffsetAbnormalSEVERE: Unit fault (Sensor circuit abnormal). TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.10 |
atsEepromAbnormalSEVERE: Unit fault (EEPROM data abnormal) TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.11 |
atsLcdNotConnectSEVERE: LCD panel connection abnormal. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.12 |
atsOutputExceedsOverloadTimeSEVERE: Overload time out, Output off, Reset needed. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.13 |
atsInputPhaseDifferenceSEVERE: Phase difference between resources exceed user defined value, Output off, Reset needed. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.14 |
atsUserSetOverLoadWARNING: User defined load pre-alarm. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.15 |
atsAtsAlarmToNormalINFORMATION: ATS Alarm Normal. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.16 |
atsSourceAvoltageAbnormalToNormalINFORMATION: Source A Voltage Normal. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.17 |
atsSourceBvoltageAbnormalToNormalINFORMATION: Source B Voltage Normal. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.18 |
atsSourceAfrequencyAbnormalToNormalINFORMATION: Source A Frequency Normal. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.19 |
atsSourceBfrequencyAbnormalToNormalINFORMATION: Source B Frequency Normal. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.20 |
atsOutputOverLoadToNormalINFORMATION: Output Load Normal. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.21 |
atsWorkPowerAabnormalToNormalINFORMATION: Unit Normal (Working power A normal). TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.22 |
atsWorkPowerBabnormalToNormalINFORMATION: Unit Normal (Working power B normal). TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.23 |
atsOverTemperatureToNormalINFORMATION: Cabinet temperature Normal. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.24 |
atsDcOffsetAbnormalToNormalINFORMATION: Unit Normal (Sensor circuit normal). TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.25 |
atsEepromAbnormalToNormalINFORMATION: Unit normal (EEPROM data normal) TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.26 |
atsLcdNotConnectToNormalINFORMATION: LCD panel connection normal. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.27 |
atsOutputExceedsOverloadTimeToNormalINFORMATION: Output Load Normal. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.28 |
atsInputPhaseDifferenceToNormalINFORMATION: Input sources return to normal phase. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.29 |
atsUserSetOverLoadToNormalINFORMATION: User defined load return to Normal. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.30 |
atsCommunicationLostSEVERE: Communication to the ATS has been lost. Steps
to reestablish communication are in progress. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.31 |
atsCommunicationEstablishedINFORMATION: Communication with the ATS has been
established. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.32 |
emdTemperatureNotHighINFORMATION: The temperature of EMD back to normal from high warning. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.33 |
emdTemperatureTooHighWARNING: The temperature of EMD higher than set point. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.34 |
emdTemperatureNotLowINFORMATION: The temperature of EMD back to normal from low warning. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.35 |
emdTemperatureTooLowWARNING: The temperature of EMD lower than set point. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.36 |
emdHumidityNotHighINFORMATION: The humidity of EMD back to normal from high warning. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.37 |
emdHumidityTooHighWARNING: The humidity of EMD higher than set point. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.38 |
emdHumidityNotLowINFORMATION: The humidity of EMD back to normal from low warning. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.39 |
emdHumidityTooLowWARNING: The humidity of EMD lower than set point. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.40 |
emdAlarm1NormalINFORMATION: The status of emd alarm-1 back to normal from active. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.41 |
emdAlarm1ActiveWARNING: The status of emd alarm-1 activated. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.42 |
emdAlarm2NormalINFORMATION: The status of emd alarm-2 back to normal from active. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.43 |
emdAlarm2ActiveWARNING: The status of emd alarm-2 activated. TRAP-TYPE .1.3.6.1.4.1.37662.1.2.2.1.2.0.44 |