ASANTE-HUB1012-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for ASANTE-HUB1012-MIB.
214
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
214 total| Object Name |
|---|
asante OBJECT IDENTIFIER .1.3.6.1.4.1.298 |
RFC1155-SMI Unknown .1.3.6.1.4.1.298 |
thresholdLev1The SNMP trap that is generated when an alarm
entry crosses its rising threshold or falling threshold, and
generates an event that is configured for sending SNMP
traps. TRAP-TYPE .1.3.6.1.4.1.298.0.1 |
nodeSecuLevel1The SNMP trap that is generated when the MAC layer
address of the incoming frame from a particular port
does not match the pre-assigned address with that port,
and generates an event that is configured for sending
SNMP traps. TRAP-TYPE .1.3.6.1.4.1.298.0.2 |
products OBJECT IDENTIFIER .1.3.6.1.4.1.298.1 |
snmpAgent OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.1 |
agentSw OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.1.1 |
agentRunTimeImageMajorVerThe major software version number of the agent
run time image.ro INTEGER .1.3.6.1.4.1.298.1.1.1.1 |
agentRunTimeImageMinorVerThe minor software version number of the agent
run time image.ro INTEGER .1.3.6.1.4.1.298.1.1.1.2 |
agentImageLoadModeTells hub whether the software image is to be
loaded from the FLASH EPROM or from over the network.rw Enumeration .1.3.6.1.4.1.298.1.1.1.3 |
agentRemoteBootInfoThe method for getting boot parameter information.ro Enumeration .1.3.6.1.4.1.298.1.1.1.4 |
agentRemoteBootProtocolThe netboot protocol that used to load the
agent software.rw Enumeration .1.3.6.1.4.1.298.1.1.1.5 |
agentRemoteBootFileThe boot file name that is sent to the boot file
server by agent boot code during boot time.rw OCTET STRING .1.3.6.1.4.1.298.1.1.1.6 |
agentOutBandDialStringThis is the initialization string used by the
Network Management station to establish the
out-of-band connection for modem only.rw OCTET STRING .1.3.6.1.4.1.298.1.1.1.7 |
agentOutBandBaudRateThe baud rate setting for the out-of-band
port.rw Enumeration .1.3.6.1.4.1.298.1.1.1.8 |
agentResetThe object to allow software to perform
'push_button' system reset.rw Enumeration .1.3.6.1.4.1.298.1.1.1.9 |
agentFw OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.1.2 |
agentFwMajorVerThe major firmware version number of the agent
prom code.ro INTEGER .1.3.6.1.4.1.298.1.1.2.1 |
agentFwMinorVerThe minor firmware version number of the agent
prom code.ro INTEGER .1.3.6.1.4.1.298.1.1.2.2 |
agentHw OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.1.3 |
agentHwReVerThe hardware reversion number of the network
management module.ro INTEGER .1.3.6.1.4.1.298.1.1.3.1 |
agentHwVerThe hardware model number of the network
management modulero INTEGER .1.3.6.1.4.1.298.1.1.3.2 |
agentNetProtoStkCapMapThis octet string represents the current
protocol stack configuration supported
by the agent, encoded as a bit string.
Each protocol stack is represented
by a single bit. When the value of a
bit = 1, it indicates that the protocol
stack on the agent represented by that
bit is supported; when zero, the protocol
stack is not supported. The number of
octets in the string is always integer
multiple of the octet. The first protocol
stack will encode in the least significant
bit of the first octet. Current, only
IP Stack(bit 0) and IPX Stack(bit 1) were
defined, all other bits should be zero.ro OCTET STRING .1.3.6.1.4.1.298.1.1.4 |
agentNetProtocol OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.1.5 |
ipagentProtocol OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.1.5.1 |
ipagentIpAddrThe ipagent's administrative IP address. The
current operational IP address can be obtained
from the ipAdEntAddr in the ipAddrTable. This
parameter will take effect only after reset hub.
This parameter will always be updated in the
EEPROM.rw IpAddress .1.3.6.1.4.1.298.1.1.5.1.1 |
ipagentIpNetMaskThe ipagent's administrative IP subnet mask. The
current operational IP subnet mask can be obtained
from the ipAdEntMask in the ipAddrTable. This
parameter will take effect only after reset hub.
This parameter will always be updated in the
EEPROM.rw IpAddress .1.3.6.1.4.1.298.1.1.5.1.2 |
ipagentDefaultGatewayThe ipagent's administrative default gateway IP
address. The current operational IP default
gateway IP address can be obtained from the
ipRouteDest in the ipRouteTable. This parameter
will take effect only after reset hub. This
parameter will always be updated in the EEPROM.rw IpAddress .1.3.6.1.4.1.298.1.1.5.1.3 |
ipagentBootServerAddrThe IP address of the boot server that was used
for booting this ipagent. This parameter will
always be updated in the EEPROM.rw IpAddress .1.3.6.1.4.1.298.1.1.5.1.4 |
ipagentUnAuthIPThe IP address of the last station that tried to
access this ipagent with an invalid community
string.ro IpAddress .1.3.6.1.4.1.298.1.1.5.1.5 |
ipagentUnAuthCommThe community string of the last station that tried
to access this ipagent with an invalid community
string.ro OCTET STRING .1.3.6.1.4.1.298.1.1.5.1.6 |
ipagentTrapRcvrTableTable consisting of the list of Network Management
Stations that are to receive traps generated by this
agent. SEQUENCE OF IpagentTrapRcvrEntry .1.3.6.1.4.1.298.1.1.5.2 |
ipagentTrapRcvrEntryDestination IP address and community string for
a particular trap server. IpagentTrapRcvrEntry .1.3.6.1.4.1.298.1.1.5.2.1 |
ipagentTrapRcvrIpAddrIP address for trap server receiving trap.ro IpAddress .1.3.6.1.4.1.298.1.1.5.2.1.1 |
ipagentTrapRcvrStatusValidation of individual trap receiver. If value
of this object is set to invalid(3), then that
particular entry is deemed invalid, meaning that
the address for that entry is no longer valid
because the entry has been removed from the table.rw Enumeration .1.3.6.1.4.1.298.1.1.5.2.1.2 |
ipagentTrapRcvrCommCommunity string for traps sent to this trap
receiver.rw OCTET STRING .1.3.6.1.4.1.298.1.1.5.2.1.3 |
adaptCard OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.2 |
concentrator OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.3 |
concChassis OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.3.1 |
concBasicGrp OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.3.1.1 |
concChassisTypeThe concentrator's chassis type.ro Enumeration .1.3.6.1.4.1.298.1.3.1.1.1 |
concChassisBkplTypeThe concentrator's chassis backplane type.ro Enumeration .1.3.6.1.4.1.298.1.3.1.1.2 |
concChassisBkplRevThe concentrator's chassis backplane
revision number.ro INTEGER .1.3.6.1.4.1.298.1.3.1.1.3 |
concChassisPsTableThis table contains concentrator's power supply
information. SEQUENCE OF ConcChassisPsEntry .1.3.6.1.4.1.298.1.3.1.1.4 |
concChassisPsEntryThe entry in the table containing the information
about a single power supply. ConcChassisPsEntry .1.3.6.1.4.1.298.1.3.1.1.4.1 |
concChassisPsIndexThe value of this object identifies the
power supply table for which this entry
contains power supply type and status.ro INTEGER .1.3.6.1.4.1.298.1.3.1.1.4.1.1 |
concChassisPsModuleTypeThe value of this object identifies the
power supply module type.ro Enumeration .1.3.6.1.4.1.298.1.3.1.1.4.1.2 |
concChassisPsStatusThe value of this object identifies the
power supply module status.ro Enumeration .1.3.6.1.4.1.298.1.3.1.1.4.1.3 |
concChassisFanStatusThe value of this object identifies the
fan status.ro Enumeration .1.3.6.1.4.1.298.1.3.1.1.5 |
concChassisGroupCapacityThe number of groups that can be contained within
the concentrator.ro INTEGER .1.3.6.1.4.1.298.1.3.1.1.6 |
concChassisGroupMapThis octet string represents the current
configuration of groups, encoded as a bit string,
each group is represented by a single bit.ro OCTET STRING .1.3.6.1.4.1.298.1.3.1.1.7 |
concChassisGrpTableA table that contains information about the
group/slot in this chassis. SEQUENCE OF ConcChassisGrpEntry .1.3.6.1.4.1.298.1.3.1.1.8 |
concChassisGrpEntryA list of information for each slot in this chassis. ConcChassisGrpEntry .1.3.6.1.4.1.298.1.3.1.1.8.1 |
concChassisGrpIndexThe value of this object identifies the
chassis group table for which this entry
contains group related information.ro INTEGER .1.3.6.1.4.1.298.1.3.1.1.8.1.1 |
concChassisGrpNumberPortThe number of port is available for up/down link
within this group.ro INTEGER .1.3.6.1.4.1.298.1.3.1.1.8.1.2 |
concChassisGrpTypeThe value represents the function of this group.ro INTEGER .1.3.6.1.4.1.298.1.3.1.1.8.1.3 |
concChassisGrpDescrA description of this group device.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.298.1.3.1.1.8.1.4 |
concChassisGrpHwRevThe hardware revision number of this particular
group.ro INTEGER .1.3.6.1.4.1.298.1.3.1.1.8.1.5 |
concConfiguration OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.3.2 |
eSmartHubConfig OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.3.2.1 |
eSmartHubIdHub MAC address (octet string) found from prom
chip in hub.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.298.1.3.2.1.1 |
eSmartHubAssignedIdAssigned hub ID for Out-of-Band.ro INTEGER .1.3.6.1.4.1.298.1.3.2.1.2 |
eSmartHubTerSwitchStatus of position of PC/terminal switch located on
rear panel of hub. Switches between serial and
parallel communications for modem/PC or terminal
connection to RS-232 Port. Up (off) for PC,
down (on) for terminal. If position of switch is
changed, there will be no change in this status
until hub is reset.ro Enumeration .1.3.6.1.4.1.298.1.3.2.1.3 |
eSmartHubHwLoadPatStatusWhich logic configuration pattern is loaded into the
Programmable Logic Device PLD.rw INTEGER .1.3.6.1.4.1.298.1.3.2.1.4 |
eSmartHubHwLoadPatCapacityWhat kind of function the PLD can perform.ro OCTET STRING .1.3.6.1.4.1.298.1.3.2.1.5 |
eSmartHubNodeAgeTimerHow long to keep node entry in node summary
table, measured in sec. The maximum is 11 hours.rw INTEGER .1.3.6.1.4.1.298.1.3.2.1.6 |
eSmartHub3in1LnConStatusStatus of 3In1 Uplink which is located on rear
panel of hub. Describes the physical link type
or types currently connected.ro Enumeration .1.3.6.1.4.1.298.1.3.2.1.7 |
eSmartHub3in1StateCtrlWhether using Auto-sense or manually selected a
particular media type for the uplink connection. If
using Auto-sense it first tries AUI. If
AUI is not present then 10T. If neither AUI nor
10T is present, then it defaults to BNC.rw Enumeration .1.3.6.1.4.1.298.1.3.2.1.8 |
concStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.3.3 |
eStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.3.3.1 |
eGlobalStatistics OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.3.3.1.1 |
eGlobalHubReadableFramesGlobal counter of good or readable frames for this
hub. Frame is between 64 and 1518 bytes in
length and has SFD and good FCS.ro Counter .1.3.6.1.4.1.298.1.3.3.1.1.1 |
eGlobalHubMcastFramesGlobal counter of number of multicast frames for
this hub. 1st bit in highest ordered bytes of
destination address is set to 1. Broadcast packets
are not included.ro Counter .1.3.6.1.4.1.298.1.3.3.1.1.2 |
eGlobalHubBcastFramesGlobal counter of number of broadcast frames for
his hub. All 1s in network destination address.
Multicast packets are not included.ro Counter .1.3.6.1.4.1.298.1.3.3.1.1.3 |
eGlobalHubFrameTooLongsGlobal counter, for this hub, of data frames
longer than 1518 bytes, with a SFD and good FCS.ro Counter .1.3.6.1.4.1.298.1.3.3.1.1.4 |
eGlobalHubRuntsGlobal counter, for this hub, of data frames with
size less than 64 bytes, with no CRC or alignment
errors.ro Counter .1.3.6.1.4.1.298.1.3.3.1.1.5 |
eGlobalHubAlignmentErrorsGlobal counter, for this hub, of frames which
are not integer multiples of 1 byte.ro Counter .1.3.6.1.4.1.298.1.3.3.1.1.6 |
eGlobalHubFragmentErrorsGlobal counter, for this hub, of frames greater than
2 bytes and less than 64 bytes, with SFD and bad
FCS (CRC error).ro Counter .1.3.6.1.4.1.298.1.3.3.1.1.7 |
eGlobalHubFCSErrorsGlobal counter, for this hub, of frames that
failed Cyclic Redundancy Check (CRC).ro Counter .1.3.6.1.4.1.298.1.3.3.1.1.8 |
eGlobalHubIFGErrorsGlobal counter, for this hub, of occurrences of
Interframe Gap Errors where time period between
data frames is less than 5.5 micro seconds.ro Counter .1.3.6.1.4.1.298.1.3.3.1.1.9 |
eGlobalHubDataRateMismatchGlobal counter, for this hub, of errors where
incoming data rate is not with in the tolerance
level of 10MHZ + or - 0.01%.ro Counter .1.3.6.1.4.1.298.1.3.3.1.1.10 |
eGlobalHubShortEventsGlobal counter, for this hub, of data burst where
data is less than 10 bytes in length, with no
SFD.ro Counter .1.3.6.1.4.1.298.1.3.3.1.1.11 |
eGlobalHubCollisionsGlobal counter of collision flags, for this hub.ro Counter .1.3.6.1.4.1.298.1.3.3.1.1.12 |
eGlobalHubLateCollisionsGlobal counter, for this hub, of collisions
occurring after the 64 byte collision window.ro Counter .1.3.6.1.4.1.298.1.3.3.1.1.13 |
eGlobalHubMJLPsGlobal counter of MAU jabber lockup protection
where hub repeater chip goes into lockup state.ro Counter .1.3.6.1.4.1.298.1.3.3.1.1.14 |
eGlobalHubAutoPartitionsGlobal counter, for this hub, of all ports including
3in1 port being partitioned from network in
response to 31 or more continuous collisions.ro Counter .1.3.6.1.4.1.298.1.3.3.1.1.15 |
eGlobalHubSFDMissingGlobal counter, for this hub, of a burst of data
greater than or equal to 10 bytes in length with
no SFD.ro Counter .1.3.6.1.4.1.298.1.3.3.1.1.16 |
eGlobalHubBadFramesGlobal counter, for this hub, of total errored frame
including toolong, runts, misaligned, or bad FCS.ro Counter .1.3.6.1.4.1.298.1.3.3.1.1.17 |
eGrpStatisticsTableTable of statistical information for each group. SEQUENCE OF EnetGrpStatisticsEntry .1.3.6.1.4.1.298.1.3.3.1.3 |
eGrpStatisticsEntryEntry for individual group in table. EnetGrpStatisticsEntry .1.3.6.1.4.1.298.1.3.3.1.3.1 |
eGrpStatIndexThe value of this object identifies the group
for which this entry contains group statistical
information.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.3.1.1 |
eGrpStatReadableFramesGroup counter of 'good' or readable frames. Frame
is between 64 and 1518 bytes in length and
has SFD and good FCS.ro Counter .1.3.6.1.4.1.298.1.3.3.1.3.1.2 |
eGrpStatMcastFramesGroup counter of number of muliticast frames.
1st bit in highest ordered bytes of destination
address is set to 1. Broadcast packets are not
included.ro Counter .1.3.6.1.4.1.298.1.3.3.1.3.1.3 |
eGrpStatBcastFramesGroup counter of number of broadcast frames. All
1s in network destination address. Multicast
packets are not included.ro Counter .1.3.6.1.4.1.298.1.3.3.1.3.1.4 |
eGrpStatFrameTooLongsGroup counter for data frames longer than 1518
bytes, with a SFD and good FCS.ro Counter .1.3.6.1.4.1.298.1.3.3.1.3.1.5 |
eGrpStatRuntsGroup counter for data frames with size less than
64 bytes, with no CRC or alignment errors.ro Counter .1.3.6.1.4.1.298.1.3.3.1.3.1.6 |
eGrpStatAlignmentErrorsGroup counter of frames which are not integer
multiples of 1 byte .ro Counter .1.3.6.1.4.1.298.1.3.3.1.3.1.7 |
eGrpStatFragmentErrorsGroup counter of frames greater than 2 bytes and
less than 64 bytes, with SFD and bad FCS
(CRC error).ro Counter .1.3.6.1.4.1.298.1.3.3.1.3.1.8 |
eGrpStatFCSErrorsGroup counter frames that failed Cyclic
Redundancy Check (CRC).ro Counter .1.3.6.1.4.1.298.1.3.3.1.3.1.9 |
eGrpStatIFGErrorsGroup counter of Interframe Gap Errors
where time period between data frames is less than
5.5 micro seconds.ro Counter .1.3.6.1.4.1.298.1.3.3.1.3.1.10 |
eGrpStatDataRateMismatchGroup counter of errors where incoming data rate
is not with in the tolerance level of
10 MHZ + or - 0.01%.ro Counter .1.3.6.1.4.1.298.1.3.3.1.3.1.11 |
eGrpStatShortEventsGroup counter of data burst where data is less than
10 bytes in length, with no SFD.ro Counter .1.3.6.1.4.1.298.1.3.3.1.3.1.12 |
eGrpStatCollisionsGroup counter of collision flags.ro Counter .1.3.6.1.4.1.298.1.3.3.1.3.1.13 |
eGrpStatLateCollisionsGroup counter of collisions occurring after the 64
byte collision window.ro Counter .1.3.6.1.4.1.298.1.3.3.1.3.1.14 |
eGrpStatMJLPsGroup counter of MAU jabber lockup protection
where hub repeater chip goes into lockup state.ro Counter .1.3.6.1.4.1.298.1.3.3.1.3.1.15 |
eGrpStatAutoPartitionsGroup counter of ports in group autopartitioned in
response to 31 or more continuous collisions.ro Counter .1.3.6.1.4.1.298.1.3.3.1.3.1.16 |
eGrpStatSFDMissingGroup counter of a burst of data greater than or
equal to 10 bytes in length with no SFD.ro Counter .1.3.6.1.4.1.298.1.3.3.1.3.1.17 |
eGrpStatBadFramesGroup counter of total errored frames including
toolong, runts, misaligned, or bad FCS.ro Counter .1.3.6.1.4.1.298.1.3.3.1.3.1.18 |
ePortStatisticsTableTable for port specific network statistics. SEQUENCE OF EnetPortStatisticsEntry .1.3.6.1.4.1.298.1.3.3.1.4 |
ePortStatisticsEntryEntry for individual port in table. EnetPortStatisticsEntry .1.3.6.1.4.1.298.1.3.3.1.4.1 |
ePortGrpIndexThe value of this object identifies the group for
which this entry contains port statistical
information.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.4.1.1 |
ePortIndexThe value of this object identifies the port for
which this entry contains port statistical
information.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.4.1.2 |
ePortStatReadableFramesPort counter of good or readable frames. Frame is
between 64 and 1518 bytes in length and
has SFD and good FCS.ro Counter .1.3.6.1.4.1.298.1.3.3.1.4.1.3 |
ePortStatMcastFramesPort counter of number of muliticast frames. 1st
bit in highest ordered bytes of destination address
is set to 1. Broadcast packets are not included.ro Counter .1.3.6.1.4.1.298.1.3.3.1.4.1.4 |
ePortStatBcastFramesPort counter of number of broadcast frames. All
1s in network destination address. Multicast
packets are not included.ro Counter .1.3.6.1.4.1.298.1.3.3.1.4.1.5 |
ePortStatFrameTooLongsPort counter for data frames longer than 1518
bytes, with a SFD and good FCS.ro Counter .1.3.6.1.4.1.298.1.3.3.1.4.1.6 |
ePortStatRuntsPort counter for data frames with size less than
64 bytes, with no CRC or alignment errors.ro Counter .1.3.6.1.4.1.298.1.3.3.1.4.1.7 |
ePortStatAlignmentErrorsPort counter of frames which are not integer
multiples of 1 byte.ro Counter .1.3.6.1.4.1.298.1.3.3.1.4.1.8 |
ePortStatFragmentErrorsPort counter of frames greater than 2 bytes and
less than 64 bytes, with SFD and bad
FCS (CRC error).ro Counter .1.3.6.1.4.1.298.1.3.3.1.4.1.9 |
ePortStatFCSErrorsPort counter of frames that failed Cyclic
Redundancy Check (CRC).ro Counter .1.3.6.1.4.1.298.1.3.3.1.4.1.10 |
ePortStatIFGErrorsPort counter of Interframe Gap Errors where
time period between data frames is less than 5.5
micro seconds.ro Counter .1.3.6.1.4.1.298.1.3.3.1.4.1.11 |
ePortStatDataRateMismatchPort counter of errors where incoming data rate
is not with in the tolerance level of
10 MHZ + or - 0.01%.ro Counter .1.3.6.1.4.1.298.1.3.3.1.4.1.12 |
ePortStatShortEventsPort counter of data burst where data is less than
10 bytes in length, with no SFD.ro Counter .1.3.6.1.4.1.298.1.3.3.1.4.1.13 |
ePortStatCollisionsPort counter of collision flags.ro Counter .1.3.6.1.4.1.298.1.3.3.1.4.1.14 |
ePortStatLateCollisionsPort counter of collisions occurring after the 64
byte collision window.ro Counter .1.3.6.1.4.1.298.1.3.3.1.4.1.15 |
ePortStatMJLPsPort counter of MAU jabber lockup protection
where hub repeater chip goes into lockup state.ro Counter .1.3.6.1.4.1.298.1.3.3.1.4.1.16 |
ePortStatAutoPartitionsPort counter of number of times port was
autopartitioned in response to 31 or more
continuous collisions.ro Counter .1.3.6.1.4.1.298.1.3.3.1.4.1.17 |
ePortStatSFDMissingPort counter of a burst of data greater than or
equal to 10 bytes in length with no SFD.ro Counter .1.3.6.1.4.1.298.1.3.3.1.4.1.18 |
ePortStatBadFramesPort counter of total errored frames including
toolong, runts, misaligned, or bad FCS.ro Counter .1.3.6.1.4.1.298.1.3.3.1.4.1.19 |
eTrafficMatrixTableTable to analyze the number of packets received
through network traffic by the size of each packet. SEQUENCE OF EnetTrafficMatrixEntry .1.3.6.1.4.1.298.1.3.3.1.5 |
eTrafficMatrixEntryIndividual entry in matrix of packet lengths table. EnetTrafficMatrixEntry .1.3.6.1.4.1.298.1.3.3.1.5.1 |
eTrafficMatrixLengthStarting length for each range in table.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.5.1.1 |
eTrafficMatrixRangeRange of packet sizes to be scanned for in network
traffic.ro Enumeration .1.3.6.1.4.1.298.1.3.3.1.5.1.2 |
eTrafficMatrixFramesCountCounter for number of frames received for
particular range specified by the MatrixRange.ro Counter .1.3.6.1.4.1.298.1.3.3.1.5.1.3 |
eSpecific OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.3.3.1.6 |
eSmartHubSpec OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.3.3.1.6.1 |
eColGraphBarInformation on hardware LED collision graph bar.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.1 |
eUtilGraphBarInformation on hardware LED for utilization
graph bar.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.2 |
ePortRateTableNetwork statistics for individual ports measured
in Rate/Second. SEQUENCE OF EnetPortRateEntry .1.3.6.1.4.1.298.1.3.3.1.6.1.6 |
ePortRateEntryIndividual entry in port rate table. EnetPortRateEntry .1.3.6.1.4.1.298.1.3.3.1.6.1.6.1 |
ePortRateGrpIndexThe value of this object identifies the group for
which this entry contains port statistical
information.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.1 |
ePortRatePortIndexThis value identifies the port for which
this entry contains port statistical information.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.2 |
ePortRateReadableFramesRate of occurrence of good or readable frames.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.3 |
ePortRateMcastFramesRate of occurrence of number of muliticast frames.
1st bit in highest ordered bytes of destination
address is set to 1. Broadcast packets are
not included.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.4 |
ePortRateBcastFramesRate of occurrence of number of broadcast frames.
All 1s in network destination address. Multicast
packets are not included.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.5 |
ePortRateFrameTooLongsRate of occurrence of data frames longer than 1518
bytes, with a SFD and good FCS.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.6 |
ePortRateRuntsRate of occurrence of data frames with size less
than 64 bytes, with no CRC or alignment errors.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.7 |
ePortRateAlignmentErrorsRate of occurrence of frames which are not integer
multiples of 1 byte.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.8 |
ePortRateFragmentErrorsRate of occurrence of frames greater than 2 bytes
and less than 64 bytes, with SFD and bad
FCS (CRC error).ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.9 |
ePortRateFCSErrorsRate of occurrence of frames that failed Cyclic
Redundancy Check (CRC).ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.10 |
ePortRateIFGErrorsRate of occurrence of interframe Gap Errors where
time period between data frames is less than 5.5
micro seconds.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.11 |
ePortRateDataRateMismatchRate of occurrence of errors where incoming data
rate is not with in the tolerance level of
10 MHz + or - 0.01%.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.12 |
ePortRateShortEventsRate of occurrence of data burst where data is less
than 10 bytes in length, with no SFD.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.13 |
ePortRateCollisionsRate of occurrence of collision flags.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.14 |
ePortRateLateCollisionsRate of occurrence of collisions occurring after the
64 byte collision window.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.15 |
ePortRateMJLPsRate of occurrence of MAU jabber lockup
protection where hub repeater chip goes into
lockup state.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.16 |
ePortRateAutoPartitionsRate of occurrence of times port was
autopartitioned in response to 31 or
more continuous collisions.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.17 |
ePortRateSFDMissingRate of occurrence of a burst of data greater than
or equal to 10 bytes in length with no SFD.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.18 |
ePortRateBadFramesRate of occurrence of total errored frames
including toolong, runts, misaligned, or bad FCS.ro INTEGER .1.3.6.1.4.1.298.1.3.3.1.6.1.6.1.19 |
concStateCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.3.4 |
eStateCtrl OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.3.4.1 |
ePortStateCtrlTableTable for port control parameters. SEQUENCE OF EPortStateCtrlEntry .1.3.6.1.4.1.298.1.3.4.1.1 |
ePortStateCtrlEntryIndividual entry of port control in table. EPortStateCtrlEntry .1.3.6.1.4.1.298.1.3.4.1.1.1 |
ePortStateGrpIndexThe value of this object identifies the group for
which this entry contains port control information.ro INTEGER .1.3.6.1.4.1.298.1.3.4.1.1.1.1 |
ePortStatePortIndexThis value identifies the port for which this
entry contains port control information.ro INTEGER .1.3.6.1.4.1.298.1.3.4.1.1.1.2 |
ePortStateTypeType of cabling physically connected to port.ro Enumeration .1.3.6.1.4.1.298.1.3.4.1.1.1.3 |
ePortStateLinkStatusLink status for particular port. On=physical link
if link test enabled. Off=no physical link
exists or link test is disabled.ro Enumeration .1.3.6.1.4.1.298.1.3.4.1.1.1.4 |
ePortStateLinkIntegTestSet can enable or disabled link integrity test.
Get will say if link integrity test is enabled (2)
or disabled (3).rw Enumeration .1.3.6.1.4.1.298.1.3.4.1.1.1.5 |
ePortStateAutoPartStatusWhether port has been autopartitioned (2) or not
autopartitioned (3).ro Enumeration .1.3.6.1.4.1.298.1.3.4.1.1.1.6 |
ePortStateJabberStatusJabber detection for port. If On(2), then
jabber occurred on this port. Off(3), then no jabber
occurred or jabber detection has been manually
disabled.ro Enumeration .1.3.6.1.4.1.298.1.3.4.1.1.1.7 |
ePortStateJabberStateSet can enable or disable jabber detection test. Get
will say if jabber detection test is enabled (2)
or disabled (3).rw Enumeration .1.3.6.1.4.1.298.1.3.4.1.1.1.8 |
ePortStateAdminStateSet will manually enable or disable any port. Get
will say if port has been enabled (2) or
disabled (3).rw Enumeration .1.3.6.1.4.1.298.1.3.4.1.1.1.9 |
ePortStateRDTStateWhether RecvThreshold has been enabled or
disabled. Can use this to lower noise threshold
(tolerance) so that longer twisted pair links
can be used.rw Enumeration .1.3.6.1.4.1.298.1.3.4.1.1.1.10 |
ePortStatePolarityStatusPolarity is correct (2) or not for this port.ro Enumeration .1.3.6.1.4.1.298.1.3.4.1.1.1.11 |
ePortStatePolarityStateAutopolarity correction enabled or disabled.
Allows hub to make electrical corrections
automatically if cable does not reverse polarity
within wire pairs. If do not want this correction to
take place, autocorrection can be disabled.rw Enumeration .1.3.6.1.4.1.298.1.3.4.1.1.1.12 |
concNodeMgt OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.3.5 |
nodeSummaryTableNode summary of all traffic through hub. SEQUENCE OF NodeSummaryEntry .1.3.6.1.4.1.298.1.3.5.1 |
nodeSummaryEntryIndividual entry in node summary table. NodeSummaryEntry .1.3.6.1.4.1.298.1.3.5.1.1 |
nodeSummaryGrpIndexGroup Id for identifying the group
where node activity is detected.ro INTEGER .1.3.6.1.4.1.298.1.3.5.1.1.1 |
nodeSummaryPortIndexPort Id for identifying the port where
node activity is detected.ro INTEGER .1.3.6.1.4.1.298.1.3.5.1.1.2 |
nodeSummarySrcMacAddrThe source MAC address of the node
that is transmitting frames
received by this port.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.298.1.3.5.1.1.3 |
nodeSummaryDestMacAddrThe destination MAC address of the
node to which frames are being
received by this port.ro PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.298.1.3.5.1.1.4 |
nodeSummaryEtherTypeThe 2 bytes after the source (src) address
in packet.ro INTEGER .1.3.6.1.4.1.298.1.3.5.1.1.5 |
nodeSummaryIpAddrPairDestination and source IP address if packet is
an Ethernet IP packet. It the packet is not an
Ethernet IP packet, then the information may
not be accurate.ro OCTET STRING .1.3.6.1.4.1.298.1.3.5.1.1.6 |
nodeSecurity OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.3.5.2 |
nodeSecuLev1TableTable of nodes which have access to particular
ports. Nodes are identified by MAC address. SEQUENCE OF NodeSecuLev1Entry .1.3.6.1.4.1.298.1.3.5.2.1 |
nodeSecuLev1EntryIndividual entry for node security table. NodeSecuLev1Entry .1.3.6.1.4.1.298.1.3.5.2.1.1 |
nodeSecuLev1GrpIndexGroup ID for port which verifying node access.ro INTEGER .1.3.6.1.4.1.298.1.3.5.2.1.1.1 |
nodeSecuLev1PortIndexSpecific port for which verifying node access.ro INTEGER .1.3.6.1.4.1.298.1.3.5.2.1.1.2 |
nodeSecuLev1StatusAddress is valid or invalid.rw Enumeration .1.3.6.1.4.1.298.1.3.5.2.1.1.3 |
nodeSecuLev1AllowedAddrMAC address of nodes allowed for particular port.rw PhysAddress (SNMPv2-TC) .1.3.6.1.4.1.298.1.3.5.2.1.1.4 |
nodeSecuLev1ActionSet action for node intrusion violation.rw Enumeration .1.3.6.1.4.1.298.1.3.5.2.1.1.5 |
concAlarmMgt OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.3.6 |
thresholdAlarm OBJECT IDENTIFIER .1.3.6.1.4.1.298.1.3.6.1 |
thresholdLev1TableThreshold/trap table. SEQUENCE OF ThresholdLev1Entry .1.3.6.1.4.1.298.1.3.6.1.1 |
thresholdLev1EntryIndividual entry in threshold trap table. ThresholdLev1Entry .1.3.6.1.4.1.298.1.3.6.1.1.1 |
thresholdLev1IndexAn index that uniquely identifies an entry in the
alarm table.ro INTEGER .1.3.6.1.4.1.298.1.3.6.1.1.1.1 |
thresholdLev1StatusStatus of entry in threshold/trap table.rw Enumeration .1.3.6.1.4.1.298.1.3.6.1.1.1.2 |
thresholdLev1TargetSet target for threshold definition. Either whole
hub(2) or particular port (3).rw Enumeration .1.3.6.1.4.1.298.1.3.6.1.1.1.3 |
thresholdLev1GroupIndexGroup ID for trap set. One note
target is selected as hub, the group index
will be ignored.rw INTEGER .1.3.6.1.4.1.298.1.3.6.1.1.1.4 |
thresholdLev1PortIndexPort number for trap set. One note
target is selected as hub, the port index
will be ignored.rw INTEGER .1.3.6.1.4.1.298.1.3.6.1.1.1.5 |
thresholdLev1SubjectVariable checking for in trap. These are the type
of frames that a trap will be verified against.rw Enumeration .1.3.6.1.4.1.298.1.3.6.1.1.1.6 |
thresholdLev1SampleTypeThe method of sampling the selected variable
and calculating the value to be compared
against the threshold.rw Enumeration .1.3.6.1.4.1.298.1.3.6.1.1.1.7 |
thresholdLev1StartupAlarmWhen the trap is triggered in relation to value set.
When goes above (2), below (3), or changes at
all from (4).rw Enumeration .1.3.6.1.4.1.298.1.3.6.1.1.1.8 |
thresholdLev1WaterMarkCounter of threshold.rw INTEGER .1.3.6.1.4.1.298.1.3.6.1.1.1.9 |
thresholdLev1DetectedValueThe value of the statistic for the last
sampling period.ro INTEGER .1.3.6.1.4.1.298.1.3.6.1.1.1.10 |
thresholdLev1RisingEventHow to respond to a triggered event for a
rising event.rw Enumeration .1.3.6.1.4.1.298.1.3.6.1.1.1.11 |
thresholdLev1FallingEventHow to respond to a triggered event for a
falling event.rw Enumeration .1.3.6.1.4.1.298.1.3.6.1.1.1.12 |
thresholdLev1IntervalThe interval in seconds over which the data is
sampled.rw INTEGER .1.3.6.1.4.1.298.1.3.6.1.1.1.13 |
thresholdLev1OwnerString8-byte octet reserved for the owner who
defined this entry.rw OCTET STRING .1.3.6.1.4.1.298.1.3.6.1.1.1.14 |
productId OBJECT IDENTIFIER .1.3.6.1.4.1.298.2 |
adapterProductId OBJECT IDENTIFIER .1.3.6.1.4.1.298.2.1 |
concProductId OBJECT IDENTIFIER .1.3.6.1.4.1.298.2.2 |
hub1012 OBJECT IDENTIFIER .1.3.6.1.4.1.298.2.2.1 |