AIRESPACE-WIRELESS-MIB
AI MIB Summary
The AIRESPACE-WIRELESS-MIB provides SNMP management for Cisco Aironet Central Controllers terminating LWAPP tunnels, enabling monitoring of 802.11 radio resource metrics, AAA authentication states, IPsec tunnel status, and global WLAN configuration parameters for associated lightweight access points.
This MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Light-weight LWAPP Access Points. This MIB provides configuration and status information for 802.11 Access Points, LAN configuration, AAA, Mobility, IpSec, Radio Rescouce Management and 802.11 global parameters. The relationship between controller and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends it to the controller to which it is logically connected. Basic Service Set Identifier (BSSID) The identifier for the service set comprising of all the 802.11 stations under the control of one coordinating Access Point. This identifier happens to be the MAC address of the dot11 radio interface of the Access Point. The wireless clients that associate with the Access Point get the wired uplink through this particular dot11 interface. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Station Management (SMT) This term refers to the internal management of the 802.11 protocol operations by the AP to work cooperatively with the other APs and 802.11 devices in the network. REFERENCE [1] Part 11 Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol.
Main OID:
bsnWireless.1.3.6.1.4.1.14179.2
1224
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
1224 total| Object Name |
|---|
bsnWirelessThis MIB is intended to be implemented on all those devices operating as Central Controllers (CC) that terminate the Light Weight Access Point Protocol tunnel from Light-weight LWAPP Access Points. This MIB provides configuration and status information for 802.11 Access Points, LAN configuration, AAA, Mobility, IpSec, Radio Rescouce Management and 802.11 global parameters. The relationship between controller and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ +......+ + + + + + + + + + CC + + CC + + CC + + CC + + + + + + + + + +......+ +......+ +......+ +......+ .. . . . .. . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + AP + + AP + + AP + + AP + + AP + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ +......+ + + + + + + + + + + + MN + + MN + + MN + + MN + + MN + + + + + + + + + + + +......+ +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends it to the controller to which it is logically connected. Basic Service Set Identifier (BSSID) The identifier for the service set comprising of all the 802.11 stations under the control of one coordinating Access Point. This identifier happens to be the MAC address of the dot11 radio interface of the Access Point. The wireless clients that associate with the Access Point get the wired uplink through this particular dot11 interface. Central Controller ( CC ) The central entity that terminates the LWAPP protocol tunnel from the LWAPP APs. Throughout this MIB, this entity also referred to as 'controller'. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Station Management (SMT) This term refers to the internal management of the 802.11 protocol operations by the AP to work cooperatively with the other APs and 802.11 devices in the network. REFERENCE [1] Part 11 Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol. MODULE-IDENTITY .1.3.6.1.4.1.14179.2 |
bsnEss OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.1 |
bsnDot11EssTableEss(WLAN) Configuration Table indexed by bsnDot11EssIndex. Maximum of 17 WLANs can be created on Airespace Switch. bsnDot11EssIndex of 17 is reserved for WLAN for Third Party APs(non-Airespace APs). Unknown .1.3.6.1.4.1.14179.2.1.1 |
bsnDot11EssEntryAn entry in bsnDot11EssTable BsnDot11EssEntry .1.3.6.1.4.1.14179.2.1.1.1 |
bsnDot11EssIndexIndex of the Ess(WLAN) within Airespace Switch. Airespace Switch supports 517 ESS(Wlans) so index will be from 1 to 517. 517 is to be used for ESS(WLAN) created for support of Third Party APs(non-Airespace APs)rw Unsigned32 .1.3.6.1.4.1.14179.2.1.1.1.1 |
bsnDot11EssSsidSSID assigned to ESS(WLAN)rw DisplayString .1.3.6.1.4.1.14179.2.1.1.1.2 |
bsnDot11EssSessionTimeoutMaximum time of a Mobile Station session. Value of 0 means infinite time(no timeout set).rw Unsigned32 .1.3.6.1.4.1.14179.2.1.1.1.4 |
bsnDot11EssMacFilteringA type of security policy for Mobile Stations (Clients). Select to filter clients by MAC address. By selecting this Security, you need to create MacFilters in bsnUsersTable or have MacFilters configured on Radius Servers specified in bsnRadiusAuthenticationTablerw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.5 |
bsnDot11EssAdminStatusAdministrative Status of ESS(WLAN). By disabling an ESS the corresponding SSID is no longer broadcasted in AP beacons.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.6 |
bsnDot11EssSecurityAuthTypeType of 802.11 Authentication.ro Enumeration .1.3.6.1.4.1.14179.2.1.1.1.7 |
bsnDot11EssStaticWEPSecurityStatus of Static WEP Security policy. If enabled, WEP Encryption WEP Default Key, Key Index and Key Format should also be specified.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.8 |
bsnDot11EssStaticWEPEncryptionTypeType of Static WEP Encryption. Length of key specified in Default Key depends on this attribute.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.9 |
bsnDot11EssStaticWEPDefaultKeyStatic WEP Default Key. For wep104 encryption either 26 bit hex key or 13 bit ascii key should be specified. For wep40 encryption 10 bit hex key or 5 bit ascii key should be specified. For wep128 encryption 32 bit hex key or 16 bit ascii key should be specified.rw WEPKeytype .1.3.6.1.4.1.14179.2.1.1.1.10 |
bsnDot11EssStaticWEPKeyIndexAccording to 802.11 standard 4 keys are supported. So 802.11 Mobile Stations(Client) can have upto 4 keys. This index is for informing Mobile Station which key it should use for Static WEP Authenticationrw INTEGER .1.3.6.1.4.1.14179.2.1.1.1.11 |
bsnDot11EssStaticWEPKeyFormatThis is not persistant.Reading this attribute will always return default. The format of the key specified in Airespace switch keeps record of the Index.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.12 |
bsnDot11Ess8021xSecurityStatus of 802.1X security policy.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.13 |
bsnDot11Ess8021xEncryptionTypeType of 802.1X Encryption. This applies if bsnDot11Ess8021xSecurity is in enabled state.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.14 |
bsnDot11EssWPASecurityStatus of WPA security policy. This has been deprecated for cLWSecDot11EssCckmTable.rwdeprecated Enumeration .1.3.6.1.4.1.14179.2.1.1.1.16 |
bsnDot11EssWPAEncryptionTypeType of WPA Encryption. This applies when bsnDot11EssWPASecurity is in enable state. This has been deprecated for cLWSecDot11EssCckmTable.rwdeprecated Enumeration .1.3.6.1.4.1.14179.2.1.1.1.17 |
bsnDot11EssIpsecSecurityStatus of IpSec (VPN) security policy. Note that this cannot be applied with Web security policy.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.18 |
bsnDot11EssVpnEncrTransformThe Encryption algorithm employed by this Vpn(IpSec) Encryption. This applies only when bsnDot11EssIpsecSecurity is in enable state.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.19 |
bsnDot11EssVpnAuthTransformThe Hash algorithm employed by the Vpn Encrpytion. This applies only when bsnDot11EssIpsecSecurity is in enable state.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.20 |
bsnDot11EssVpnIkeAuthModeThe authentication type of the SA. It could be a certificate or a pre-shared key or xauthEnablePsk. This applies only when bsnDot11EssIpsecSecurity is in enable state.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.21 |
bsnDot11EssVpnSharedKeyVPN Shared Key. This applies only when bsnDot11EssVpnSharedKey is in enable state and bsnDot11EssVpnIkeAuthMode is xauthEnablePsk or presharedKey.rw OCTET STRING .1.3.6.1.4.1.14179.2.1.1.1.22 |
bsnDot11EssVpnSharedKeySizeVPN Shared Key size. This applies only when bsnDot11EssVpnSharedKey is in enable state and bsnDot11EssVpnIkeAuthMode is xauthEnablePsk or presharedKey.ro Unsigned32 .1.3.6.1.4.1.14179.2.1.1.1.23 |
bsnDot11EssVpnIkePhase1ModeVPN IKE Phase 1 Mode type as per the IpSec standards. This applies only when bsnDot11EssIpsecSecurity is in enable state.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.24 |
bsnDot11EssVpnIkeLifetimeVpn IKE's Lifetime. This applies only when bsnDot11EssIpsecSecurity is in enable state.rw Integer32 .1.3.6.1.4.1.14179.2.1.1.1.25 |
bsnDot11EssVpnIkeDHGroupIKE's Diffie-Hellman Group. This applies only when bsnDot11EssIpsecSecurity is in enable state.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.26 |
bsnDot11EssIpsecPassthruSecurityStatus of IpSec Passthru security policy.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.27 |
bsnDot11EssVpnPassthruGatewayIp address of VpnPassthru Gateway. This applies only when bsnDot11EssIpsecPassthruSecurity is in enable state.rw IpAddress .1.3.6.1.4.1.14179.2.1.1.1.28 |
bsnDot11EssWebSecurityStatus of Web security policy. Note this policy cannot be applied with IpSec security policy.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.29 |
bsnDot11EssRadioPolicyRadio Policy for a WLAN. It can either be All where it will be applicable to ALL types of protocols or it can be set to apply to combinations of 802.11a, 802.11b, 802.11g.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.30 |
bsnDot11EssQualityOfServiceQuality of Service for a WLAN.Services such as VoIP should be set to Gold while non-discriminating services such as messaging can be set to Bronze.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.31 |
bsnDot11EssDhcpRequiredDHCP required for all clients on this WLANrw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.32 |
bsnDot11EssDhcpServerIpAddressIP Address of the DHCP Server. Make it 0.0.0.0 to disable DHCP Relay. Any value other than 0.0.0.0, it will be assumed that DHCP Relay is turned on.rw IpAddress .1.3.6.1.4.1.14179.2.1.1.1.33 |
bsnDot11EssVpnContivityModeSpecifies if contivity mode for the IpSec is enabled. If enabled, user needs to specify the Quote of the Day Server's IPAddress in bsnDot11EssVpnQotdServerAddress.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.34 |
bsnDot11EssVpnQotdServerAddressIP Address of the Quote of the Day Server.rw IpAddress .1.3.6.1.4.1.14179.2.1.1.1.35 |
bsnDot11EssBlacklistTimeoutSet the timeout for blacklisted Mobile Stations after which the mobile station will be automatically de-authenticated. Mobile Station are blacklisted by MAC address and their status can be obtained from bsnMobileStationStatus. A timeout setting of 0 indicates no blacklist timeout is set and administrative control (bsnMobileStationDeleteAction ) is required to deauthenticate the station.rw Integer32 .1.3.6.1.4.1.14179.2.1.1.1.37 |
bsnDot11EssNumberOfMobileStationsNo of Mobile Stations currently associated with the WLAN.ro Counter32 .1.3.6.1.4.1.14179.2.1.1.1.38 |
bsnDot11EssWebPassthruFor switches with version before 2.0: This is applicable only when the Web Security Type is enabled. When this attribute is enabled, it allows a client's NetBIOS packets to go through the switch before web auth is completed. (This is obsolete for Switch versions 2.0 to 2.2). For switch verions 3.0 and above: This is reintroduced as the web policy where the client is connected through the web without authentication that is there is no username/password input required. Moreover, if the bsnDot11EssWebPassthroughEmail is enabled, the user will be asked to enter an email address.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.39 |
bsnDot11EssCraniteSecurityStatus of Cranite Passthrough Security policy. If enabled, no other security can be enabled.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.40 |
bsnDot11EssBlacklistingCapabilityThis is the flag that can enable or disable the client backlisting feature for a WLAN. If enabled, the clients can be blacklisted by the Switch in case of repetitive auth failure and other reasons like it. If disabled, the clients cannot be blacklisted by the switch. The blacklist timeout value will only be effective if this feature is turned on.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.41 |
bsnDot11EssInterfaceNameName of the interface used by this WLAN. By default it is set to be the management interface.rw DisplayString .1.3.6.1.4.1.14179.2.1.1.1.42 |
bsnDot11EssAclNameName of ACL for the WLAN. This is applicable only when Web Authentication is enabled as a security. An empty string value indicates that no ACL has been set (which is a valid option)rw DisplayString .1.3.6.1.4.1.14179.2.1.1.1.43 |
bsnDot11EssAAAOverrideEnable or Disable AAA override for the global WLAN parameters.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.44 |
bsnDot11EssWPAAuthKeyMgmtModeEnable or Disable WPA Pre-shared Key Mode. If enabled, a preshared key should be set for WPA authentication. This has been deprecated for cLWSecDot11EssCckmTable.rwdeprecated Enumeration .1.3.6.1.4.1.14179.2.1.1.1.45 |
bsnDot11EssWPAAuthPresharedKeyWPA Authentication Preshared Key. This applies only when bsnDot11EssWPAAuthKeyMgmtMode is in enable state. This has been deprecated for cLWSecDot11EssCckmTable.rwdeprecated OCTET STRING .1.3.6.1.4.1.14179.2.1.1.1.46 |
bsnDot11EssFortressSecurityStatus of Fortress Passthrough Security policy. If enabled, no other security can be enabled.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.47 |
bsnDot11EssWepAllowSharedKeyAuthEnable this flag to allow Shared Key Authentication when Static WEP is enabled.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.48 |
bsnDot11EssL2tpSecurityStatus of L2TP security policy. Note that this cannot be applied with Web security policy, Cranite or Fortress policy.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.49 |
bsnDot11EssWPAAuthPresharedKeyHexWPA Authentication Preshared Key in the hex format. This applies only when bsnDot11EssWPAAuthKeyMgmtMode is in enable state. This has been deprecated for cLWSecDot11EssCckmTable.rwdeprecated OCTET STRING .1.3.6.1.4.1.14179.2.1.1.1.50 |
bsnDot11EssBroadcastSsidThis attribute when enabled allows the switch to broadcast this SSID.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.51 |
bsnDot11EssExternalPolicyValidationThis attribute specifies if external policy servers will be used for validation. If no servers are configured in bsnExternalPolicyServerTable then it cannot be enabled.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.52 |
bsnDot11EssRSNSecurityThis attribute specifies status of RSN Security Policy. This has been deprecated for cLWSecDot11EssCckmTable.rwdeprecated Enumeration .1.3.6.1.4.1.14179.2.1.1.1.53 |
bsnDot11EssRSNWPACompatibilityModeThis attribute specifies RSN security's compatibility mode with WPA. This has been deprecated for cLWSecDot11EssCckmTable.rwdeprecated Enumeration .1.3.6.1.4.1.14179.2.1.1.1.54 |
bsnDot11EssRSNAllowTKIPClientsThis attribute specifies whether TKIP clients are allowed by RSN Policy. This has been deprecated for cLWSecDot11EssCckmTable.rwdeprecated Enumeration .1.3.6.1.4.1.14179.2.1.1.1.55 |
bsnDot11EssRSNAuthKeyMgmtModeThis attribute specifies whether Preshared key is used or not. If used user should specify a key between 8 and 63 characters in bsnDot11EssRSNAuthPresharedKey attribute. This has been deprecated for cLWSecDot11EssCckmTable.rwdeprecated Enumeration .1.3.6.1.4.1.14179.2.1.1.1.56 |
bsnDot11EssRSNAuthPresharedKeyRSN Authentication Preshared Key. This applies only when bsnDot11EssRSNAuthKeyMgmtMode is in enable state. This has been deprecated for cLWSecDot11EssCckmTable.rwdeprecated OCTET STRING .1.3.6.1.4.1.14179.2.1.1.1.57 |
bsnDot11EssRSNAuthPresharedKeyHexRSN Authentication Preshared Key in the hex format. This applies only when bsnDot11EssWPAAuthKeyMgmtMode is in enable state. This has been deprecated for cLWSecDot11EssCckmTable.rwdeprecated OCTET STRING .1.3.6.1.4.1.14179.2.1.1.1.58 |
bsnDot11EssIPv6BridgingWhen enabled, IPv6 bridging is applied on the packets.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.59 |
bsnDot11EssRowStatusA row status type for the bsnDot11EssEntryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.1.1.60 |
bsnDot11EssWmePolicySettingWhen enabled, WME Policy is applied on the packets.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.61 |
bsnDot11Ess80211ePolicySettingWhen enabled, 802.11e Policy is applied on the packets.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.62 |
bsnDot11EssWebPassthroughEmailWhen enabled, along with the bsnDot11EssWebPassthru attribute, the client is allowed to connect by entering his/her email address on the web connection page. There is no further authentication required.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.63 |
bsnDot11Ess7920PhoneSupportWhen client cac limit is enabled, the 7920 Phones with old software where the Call Admission Control (CAC) Limit is Specified on the client will be supported on the WLAN. The support for clientCacLimit (by setting to value 1 or 3) cannot be enabled when the bsnDot11EssWmePolicySetting is set to allowed or required. When ap cac limit is enabled, the 7920 Phones with new software where the Call Admission Control (CAC) Limit is advertised by the AP, will be supported on the WLAN.rw Enumeration .1.3.6.1.4.1.14179.2.1.1.1.64 |
bsnDot11EssRadiusAuthPrimaryServerPrimary Radius Authentication Server for this wlan.rw DisplayString .1.3.6.1.4.1.14179.2.1.1.1.95 |
bsnDot11EssRadiusAuthSecondaryServerSecondary Radius Authentication Server for this wlan.rw DisplayString .1.3.6.1.4.1.14179.2.1.1.1.96 |
bsnDot11EssRadiusAuthTertiaryServerTertiary Radius Authentication Server for this wlan.rw DisplayString .1.3.6.1.4.1.14179.2.1.1.1.97 |
bsnDot11EssRadiusAcctPrimaryServerPrimary Radius Accounting Server for this wlan.rw DisplayString .1.3.6.1.4.1.14179.2.1.1.1.98 |
bsnDot11EssRadiusAcctSecondaryServerSecondary Radius Accounting Server for this wlan.rw DisplayString .1.3.6.1.4.1.14179.2.1.1.1.99 |
bsnDot11EssRadiusAcctTertiaryServerTertiary Radius Accounting Server for this wlan.rw DisplayString .1.3.6.1.4.1.14179.2.1.1.1.100 |
bsnMobileStationTableMobile Station Table indexed by bsnMobileStationMacAddress. (Mobile Station is better referred to as Client in the current releases.) SEQUENCE OF BsnMobileStationEntry .1.3.6.1.4.1.14179.2.1.4 |
bsnMobileStationEntryAn entry in bsnMobileStationTable. BsnMobileStationEntry .1.3.6.1.4.1.14179.2.1.4.1 |
bsnMobileStationMacAddress802.11 MAC Address of the Mobile Station.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.4.1.1 |
bsnMobileStationIpAddressIP Address of the Mobile Stationro IpAddress .1.3.6.1.4.1.14179.2.1.4.1.2 |
bsnMobileStationUserNameUser Name,if any, of the Mobile Station. This would be non empty in case of Web Authentication and IPSec.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.4.1.3 |
bsnMobileStationAPMacAddr802.11 Mac Address of the AP to which the Mobile Station is associated.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.4.1.4 |
bsnMobileStationAPIfSlotIdSlot ID of AP Interface to which the mobile station is associated. The value 15 is used to indicate that the slot Id is invalid.ro INTEGER .1.3.6.1.4.1.14179.2.1.4.1.5 |
bsnMobileStationEssIndexEss Index of the Wlan(SSID) that is being used by Mobile Station to connect to APro INTEGER .1.3.6.1.4.1.14179.2.1.4.1.6 |
bsnMobileStationSsidThe SSID Advertised by Mobile Stationro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.4.1.7 |
bsnMobileStationAIDAID for the mobile stationro Unsigned32 .1.3.6.1.4.1.14179.2.1.4.1.8 |
bsnMobileStationStatusStatus of the mobile stationro Enumeration .1.3.6.1.4.1.14179.2.1.4.1.9 |
bsnMobileStationReasonCodeReason Code as defined by 802.11 standardsro Enumeration .1.3.6.1.4.1.14179.2.1.4.1.10 |
bsnMobileStationMobilityStatusMobility Role of the Mobile Station.ro Enumeration .1.3.6.1.4.1.14179.2.1.4.1.11 |
bsnMobileStationAnchorAddressIf the Mobility Status of the Mobile Station is Anchor then it will have Peer Ip Address and will have Anchor IP if the Role is Foreignro IpAddress .1.3.6.1.4.1.14179.2.1.4.1.12 |
bsnMobileStationCFPollableWhen this attribute is true, it shall indicate that the Mobile Station is able to respond to a CF-Poll with a data frame within a SIFS time. This attribute shall be false if the Mobile Station is not able to respond to a CF-Poll with a data frame within a SIFS time.ro Enumeration .1.3.6.1.4.1.14179.2.1.4.1.13 |
bsnMobileStationCFPollRequestSpecifies whether CFP is requested by Mobile Station or notro Enumeration .1.3.6.1.4.1.14179.2.1.4.1.14 |
bsnMobileStationChannelAgilityEnabledThis attribute indicates that the PHY channel agility functionality is enabled.ro Enumeration .1.3.6.1.4.1.14179.2.1.4.1.15 |
bsnMobileStationPBCCOptionImplementedThis attribute, when true, shall indicate that the PBCC modulation option as defined in subclause 18.4.6.6 is implemented. The default value of this attribute shall be false.ro Enumeration .1.3.6.1.4.1.14179.2.1.4.1.16 |
bsnMobileStationShortPreambleOptionImplementedThis attribute, when true, shall indicate that the short preamble option as defined in subclause 18.2.2.2 is implemented. The default value of this attribute shall be false.ro Enumeration .1.3.6.1.4.1.14179.2.1.4.1.17 |
bsnMobileStationSessionTimeoutSession Timeout of Mobile stationro Unsigned32 .1.3.6.1.4.1.14179.2.1.4.1.18 |
bsnMobileStationAuthenticationAlgorithmAuthentication Algorithm of Mobile Stationro Enumeration .1.3.6.1.4.1.14179.2.1.4.1.19 |
bsnMobileStationWepStateWEP State of Mobile Stationro Enumeration .1.3.6.1.4.1.14179.2.1.4.1.20 |
bsnMobileStationPortNumberThe Port Number of this Airespace Switch on which the traffic of the Mobile Station is coming through.ro Unsigned32 .1.3.6.1.4.1.14179.2.1.4.1.21 |
bsnMobileStationDeleteActionAction to Deauthenticate the Mobile Station. Set the State to delete.rw Enumeration .1.3.6.1.4.1.14179.2.1.4.1.22 |
bsnMobileStationPolicyManagerStatePolicy Manager State of the mobile station.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.4.1.23 |
bsnMobileStationSecurityPolicyStatusWhen this attribute has value completed, it shall indicate that the Mobile Station has completed the security policy checks. Otherwise the checks are yet to be completed.ro Enumeration .1.3.6.1.4.1.14179.2.1.4.1.24 |
bsnMobileStationProtocolThe 802.11 protocol type of the client. The protocol is mobile when this client detail is seen on the anchor i.e it's mobility status is anchor.ro Enumeration .1.3.6.1.4.1.14179.2.1.4.1.25 |
bsnMobileStationMirrorModeIf enabled, then mirroring for this client will be statically configured irrespective of the AP and the port this client is on.rw Enumeration .1.3.6.1.4.1.14179.2.1.4.1.26 |
bsnMobileStationInterfaceName of the Interface of the mobile client to the switch.ro DisplayString .1.3.6.1.4.1.14179.2.1.4.1.27 |
bsnMobileStationApModeMode of the AP to which the Mobile Station is associated.ro Enumeration .1.3.6.1.4.1.14179.2.1.4.1.28 |
bsnMobileStationVlanIdVlan ID of the Interface to which the client is associated.ro Integer32 .1.3.6.1.4.1.14179.2.1.4.1.29 |
bsnMobileStationPolicyTypeMode of the AP to which the Mobile Station is associated.ro Enumeration .1.3.6.1.4.1.14179.2.1.4.1.30 |
bsnMobileStationEncryptionCypherMode of the AP to which the Mobile Station is associated.ro Enumeration .1.3.6.1.4.1.14179.2.1.4.1.31 |
bsnMobileStationEapTypeMode of the AP to which the Mobile Station is associated.ro Enumeration .1.3.6.1.4.1.14179.2.1.4.1.32 |
bsnMobileStationCcxVersionRepresents the Cisco Compatible Extensions (CCX) Version the client is using for communication with the AP.ro Enumeration .1.3.6.1.4.1.14179.2.1.4.1.33 |
bsnMobileStationE2eVersionRepresents the End-2-End Version the client is using for communication with the AP.ro Enumeration .1.3.6.1.4.1.14179.2.1.4.1.34 |
bsnMobileStationStatusCodeStatus Code of the Mobile Stationro INTEGER .1.3.6.1.4.1.14179.2.1.4.1.42 |
bsnMobileStationPerRadioPerVapTableMobile Station Per Radio Per VAP(WLAN) Table. This table lists all Mobile Stations on a particular Airespace AP Interface for a particular ESS(Wlan). It only lists MAC Addresses. Further details for a Mobile Station can be found from bsnMobileStationTable once the MAC Address is knonwn. (Mobile Station is better referred to as Client in the current releases.) SEQUENCE OF BsnMobileStationPerRadioPerVapEntry .1.3.6.1.4.1.14179.2.1.5 |
bsnMobileStationPerRadioPerVapEntryAn entry in MobileStationPerRadioPerVapTable. BsnMobileStationPerRadioPerVapEntry .1.3.6.1.4.1.14179.2.1.5.1 |
bsnMobileStationPerRadioPerVapIndexThe index of Mobile Station. The index starts from 1 and goes upto the total number of Mobile Stations on Airespace Radio Interface for a specific ESS (Wlan).ro Integer32 .1.3.6.1.4.1.14179.2.1.5.1.1 |
bsnMobileStationMacAddrThe MAC Address of Mobile Station.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.5.1.20 |
bsnMobileStationStatsTableMobile Station Statistics Table. (Mobile Station is better referred to as Client in the current releases.) SEQUENCE OF BsnMobileStationStatsEntry .1.3.6.1.4.1.14179.2.1.6 |
bsnMobileStationStatsEntryAn entry in bsnMobileStationStatsTable. BsnMobileStationStatsEntry .1.3.6.1.4.1.14179.2.1.6.1 |
bsnMobileStationRSSIAverage packet RSSI for the Mobile Station.ro Integer32 .1.3.6.1.4.1.14179.2.1.6.1.1 |
bsnMobileStationBytesReceivedBytes received from Mobile Stationro Counter64 .1.3.6.1.4.1.14179.2.1.6.1.2 |
bsnMobileStationBytesSentBytes sent to Mobile Stationro Counter64 .1.3.6.1.4.1.14179.2.1.6.1.3 |
bsnMobileStationPolicyErrorsNumber of Policy Errors for Mobile Stationro Counter64 .1.3.6.1.4.1.14179.2.1.6.1.4 |
bsnMobileStationPacketsReceivedPackets received from Mobile Stationro Counter64 .1.3.6.1.4.1.14179.2.1.6.1.5 |
bsnMobileStationPacketsSentPackets sent to Mobile Stationro Counter64 .1.3.6.1.4.1.14179.2.1.6.1.6 |
bsnMobileStationSnrSignal to noise Ratio of the Mobile Station.ro Integer32 .1.3.6.1.4.1.14179.2.1.6.1.26 |
bsnRogueAPTableRogue Table. This table lists all the Rogue APs detected by Airespace APs. SEQUENCE OF BsnRogueAPEntry .1.3.6.1.4.1.14179.2.1.7 |
bsnRogueAPEntryAn Entry in bsnRogueAPTable. BsnRogueAPEntry .1.3.6.1.4.1.14179.2.1.7.1 |
bsnRogueAPDot11MacAddressMAC Address of Rogue Station.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.7.1.1 |
bsnRogueAPTotalDetectingAPsTotal number of Airespace APs that detected this rogue.ro Integer32 .1.3.6.1.4.1.14179.2.1.7.1.2 |
bsnRogueAPFirstReportedTime Stamp when this Rogue was First Detected.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.7.1.3 |
bsnRogueAPLastReportedTime Stamp when this Rogue was Last Detected.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.7.1.4 |
bsnRogueAPContainmentLevelIf the state of the rogue is contained, this specifies the level of containment. Higher the level, more the number of detecting APs that are used to contain it. The value must be between 1 to 4 for 'contained' state.rw Enumeration .1.3.6.1.4.1.14179.2.1.7.1.5 |
bsnRogueAPTypeThis attribute specifies if the Rogue is of ad-hoc type or is an AP.ro Enumeration .1.3.6.1.4.1.14179.2.1.7.1.6 |
bsnRogueAPOnNetworkThis attribute specifies if the Rogue is on Wired Network or not.ro Enumeration .1.3.6.1.4.1.14179.2.1.7.1.7 |
bsnRogueAPTotalClientsTotal number of Clients detected on this rogue.ro Integer32 .1.3.6.1.4.1.14179.2.1.7.1.8 |
bsnRogueAPRowStatusRow Statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.7.1.9 |
bsnRogueAPMaxDetectedRSSIThis is the max RSSI value of all the detctecting APs, which have detected this rogue.ro Integer32 .1.3.6.1.4.1.14179.2.1.7.1.10 |
bsnRogueAPSSIDThis is the SSID of the rogue detected by Access Point, which has max RSSI value of all the detectecting APs of this rogue.ro DisplayString .1.3.6.1.4.1.14179.2.1.7.1.11 |
bsnRogueAPDetectingAPRadioTypeRadio type of detecting APs. If the radio type is detected by dot11bg radio or dot11a radio or both.ro Bits .1.3.6.1.4.1.14179.2.1.7.1.12 |
bsnRogueAPDetectingAPMacAddressMAC Address of of detecting AP which received max RSSIro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.7.1.13 |
bsnRogueAPMaxRssiRadioTypeThe radio type of detecting AP which received max RSSI value.ro Enumeration .1.3.6.1.4.1.14179.2.1.7.1.14 |
bsnRogueAPStateThis attribute is use to specify the state in which the Rogue AP is user can set the Rogue AP in alert, known or acknowledge state. Alert state means Rogue AP can be a potential threat. Trap will be sent out to trap recipients. Known state means its just internal AP which is not on the same Switch. Acknowledge state means an external AP whose existence is acceptable and not a threat (probably some other company's AP). Contained means containement is initiated and ongoing. Threat is usually the state when the rogue is found on wired network. known(4), knownContained(9) and trustedMissing(10) will appear in known rogue list. known rogues can be pre provisioned and known rogues state can be changed to alert(2)rw Enumeration .1.3.6.1.4.1.14179.2.1.7.1.24 |
bsnRogueAPClassTypeThe AP class type of the client detected.rw Enumeration .1.3.6.1.4.1.14179.2.1.7.1.25 |
bsnRogueAPChannelThis is the channel number of the last detecting APs, which has detected this rogue.ro Integer32 .1.3.6.1.4.1.14179.2.1.7.1.26 |
bsnRogueAPDetectingAPNameAP name of the detecting AP which received max RSSIrw OCTET STRING .1.3.6.1.4.1.14179.2.1.7.1.27 |
bsnRogueAPAirespaceAPTableRogue Station Table. This table lists all the Airespace AP Interfaces that detected a particular Rogue. SEQUENCE OF BsnRogueAPAirespaceAPEntry .1.3.6.1.4.1.14179.2.1.8 |
bsnRogueAPAirespaceAPEntryAn entry in bsnRogueAPAirespaceAPEntry. BsnRogueAPAirespaceAPEntry .1.3.6.1.4.1.14179.2.1.8.1 |
bsnRogueAPAirespaceAPMacAddressMAC Address of Airespace AP Interface that Detected the Rogue.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.8.1.1 |
bsnRogueAPAirespaceAPSlotIdThe slot ID of the Airespace AP Interface that detected the Rogue.ro Unsigned32 .1.3.6.1.4.1.14179.2.1.8.1.2 |
bsnRogueAPRadioTypeThe Airespace AP Interface type that detected the Rogue.ro Enumeration .1.3.6.1.4.1.14179.2.1.8.1.3 |
bsnRogueAPAirespaceAPNameName of Airespace AP Interface that detected the Rogue.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.8.1.4 |
bsnRogueAPChannelNumberThe advertised Channel Number of the Airespace AP Interface picked up from the Rogue.ro Integer32 .1.3.6.1.4.1.14179.2.1.8.1.5 |
bsnRogueAPSsidThe SSID Advertised by Rogue Station.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.8.1.6 |
bsnRogueAPAirespaceAPRSSIRogue RSSI as seen by Airespace AP Interface.ro Integer32 .1.3.6.1.4.1.14179.2.1.8.1.7 |
bsnRogueAPContainmentModeIf the rogue is in 'contained' state, this attribute shows the containment mode used by the AP.ro Enumeration .1.3.6.1.4.1.14179.2.1.8.1.8 |
bsnRogueAPContainmentChannelCountThe number of channels used for rogue containment.ro Unsigned32 .1.3.6.1.4.1.14179.2.1.8.1.9 |
bsnRogueAPContainmentChannelsThis is the comma separated string of channels used for rogue containment.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.8.1.10 |
bsnRogueAPAirespaceAPLastHeardNo of seconds ago when this Rogue was last heard by this AP.ro Counter32 .1.3.6.1.4.1.14179.2.1.8.1.11 |
bsnRogueAPAirespaceAPWepModeThe WEP mode on this detecting AP.ro Enumeration .1.3.6.1.4.1.14179.2.1.8.1.12 |
bsnRogueAPAirespaceAPPreambleThe Preamble on this detecting AP.ro Enumeration .1.3.6.1.4.1.14179.2.1.8.1.13 |
bsnRogueAPAirespaceAPWpaModeThe WPA mode on this detecting AP.ro Enumeration .1.3.6.1.4.1.14179.2.1.8.1.14 |
bsnRogueAPAirespaceAPSNRSNR seen by Airespace AP Interface from Roguero Integer32 .1.3.6.1.4.1.14179.2.1.8.1.27 |
bsnRogueAPChannelWidthThis object represents the channel width of the rogue.ro Enumeration .1.3.6.1.4.1.14179.2.1.8.1.28 |
bsnThirdPartyAPTableThird Party Access Point Table. An entry needs to be configured in this table for a third party access point that needs to be supported by the Switch. Note: A third party ESS (Wlan) with ID 17 should be created in bsnDot11EssTable before adding entries here. Please also note that ACS currently supports only Aironet 350, 1200 and Orinoco 2000 Access Points as third party APs.obsolete SEQUENCE OF BsnThirdPartyAPEntry .1.3.6.1.4.1.14179.2.1.9 |
bsnThirdPartyAPEntryAn entry in bsnThirdPartyAPTable.obsolete BsnThirdPartyAPEntry .1.3.6.1.4.1.14179.2.1.9.1 |
bsnThirdPartyAPMacAddressMAC Address of Third Party Access Point which is connected directly to this Airespace Switch.rwobsolete MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.9.1.1 |
bsnThirdPartyAPInterfaceInterface(Port Number) to which the Third Party AP is connected.rwobsolete Integer32 .1.3.6.1.4.1.14179.2.1.9.1.2 |
bsnThirdPartyAPIpAddressStatic IP address of the 3rd Party AP, 0.0.0.0 indicating x its using DHCPrwobsolete IpAddress .1.3.6.1.4.1.14179.2.1.9.1.3 |
bsnThirdPartyAP802Dot1XRequiredIf 802.1X is required for the 3rd Party APrwobsolete Enumeration .1.3.6.1.4.1.14179.2.1.9.1.4 |
bsnThirdPartyAPMirrorModeIf enabled, then data from all the foreign AP users and all the foreign APs on this APs port will be mirrored. These clients are dynamically added to the switch's mirrored MAC list.rwobsolete Enumeration .1.3.6.1.4.1.14179.2.1.9.1.5 |
bsnThirdPartyAPRowStatusRow Status in the ThirdPartyAPEntry.rwobsolete RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.9.1.24 |
bsnMobileStationByIpTableMobile Station Table indexed by bsnMobileStationByIpAddress. NOTE: This is just to facilitate the search of mobile stations based on IP Address. Doing a get without the index doesn't return anything. (Mobile Station is better referred to as Client in the current releases.) SEQUENCE OF BsnMobileStationByIpEntry .1.3.6.1.4.1.14179.2.1.10 |
bsnMobileStationByIpEntryAn entry in bsnMobileStationByIpTable. BsnMobileStationByIpEntry .1.3.6.1.4.1.14179.2.1.10.1 |
bsnMobileStationByIpAddressIP Address of the Mobile Stationro IpAddress .1.3.6.1.4.1.14179.2.1.10.1.1 |
bsnMobileStationByIpMacAddress802.11 Mac Address of the Mobile Station.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.10.1.2 |
bsnMobileStationRssiDataTableMobile Station RSSI data Table indexed by bsnMobileStationMacAddress, bsnMobileStationRssiDataApMacAddress, bsnMobileStationRssiDataApIfSlotId. (Mobile Station is better referred to as Client in the current releases.) SEQUENCE OF BsnMobileStationRssiDataEntry .1.3.6.1.4.1.14179.2.1.11 |
bsnMobileStationRssiDataEntryAn entry in bsnMobileStationRssiDataTable. BsnMobileStationRssiDataEntry .1.3.6.1.4.1.14179.2.1.11.1 |
bsnMobileStationRssiDataApMacAddress802.11 Mac Address of the AP on which Mobile Station is associated.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.11.1.1 |
bsnMobileStationRssiDataApIfSlotIdSlotId of APIf on which mobile station is associatedro Unsigned32 .1.3.6.1.4.1.14179.2.1.11.1.2 |
bsnMobileStationRssiDataApIfTypeThe interface type of the radio that sensed the rssi data.ro Enumeration .1.3.6.1.4.1.14179.2.1.11.1.3 |
bsnMobileStationRssiDataApNameThe Name of the AP that sensed the rssi data.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.11.1.4 |
bsnMobileStationRssiDataRSSI seen by Airespace AP Interface for the Mobile Stationro Integer32 .1.3.6.1.4.1.14179.2.1.11.1.5 |
bsnAPIfPhyAntennaIndexAntenna which recived the probe request from client. The antenna which reported the RSSI value for the client. For now value will be 0 to 1, in future it may change.ro Unsigned32 .1.3.6.1.4.1.14179.2.1.11.1.6 |
bsnMobileStationRssiDataLastHeardNo of seconds ago when this RSSI data was recorded.ro Counter32 .1.3.6.1.4.1.14179.2.1.11.1.25 |
bsnWatchListClientTableTable of watch listed clients. When clients are added to this table by username or MAC address, ACS collects data for them to show trend reports. The switch generates Client Association and Client Authentication traps for the watch listed clients.The watch list feature can be enbaled or diabled by the bsnWatchListFeatureEnable flag on the switch.obsolete SEQUENCE OF BsnWatchListClientEntry .1.3.6.1.4.1.14179.2.1.12 |
bsnWatchListClientEntryAn entry in bsnWatchListClientTable.obsolete BsnWatchListClientEntry .1.3.6.1.4.1.14179.2.1.12.1 |
bsnWatchListClientKeyMAC Address or User Name of Client that is to be added to the watch list.rwobsolete OCTET STRING .1.3.6.1.4.1.14179.2.1.12.1.1 |
bsnWatchListClientTypeThe type of the watch list client entry. The entry can be created by Client MAC Address or by Username.rwobsolete Enumeration .1.3.6.1.4.1.14179.2.1.12.1.2 |
bsnWatchListClientRowStatusA row status type for the bsnWatchListClientEntryrwobsolete RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.12.1.20 |
bsnMobileStationByUsernameTableMobile Station Table indexed by the Mobile Station Username and MAC Address. NOTE: This is just to facilitate the search of mobile stations based on User Name. Doing a get without the username doesn't return anything. (Mobile Station is better referred to as Client in the current releases.) SEQUENCE OF BsnMobileStationByUsernameEntry .1.3.6.1.4.1.14179.2.1.13 |
bsnMobileStationByUsernameEntryAn entry in bsnMobileStationByUsernameTable. BsnMobileStationByUsernameEntry .1.3.6.1.4.1.14179.2.1.13.1 |
bsnMobileStationByUserNameUsername of the Mobile Stationro OCTET STRING .1.3.6.1.4.1.14179.2.1.13.1.1 |
bsnMobileStationByUserMacAddress802.11 Mac Address of the Mobile Station.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.13.1.2 |
bsnRogueClientTableRogue Client Table. This table lists all the Rogue Clients detected by Airespace APs. SEQUENCE OF BsnRogueClientEntry .1.3.6.1.4.1.14179.2.1.14 |
bsnRogueClientEntryAn Entry in bsnRogueClientTable. BsnRogueClientEntry .1.3.6.1.4.1.14179.2.1.14.1 |
bsnRogueClientDot11MacAddressMac Address of Rogue Station. MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.14.1.1 |
bsnRogueClientTotalDetectingAPsTotal number of Airespace APs that detected this rogue.ro Integer32 .1.3.6.1.4.1.14179.2.1.14.1.2 |
bsnRogueClientFirstReportedTime Stamp when this Rogue was First Detected.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.14.1.3 |
bsnRogueClientLastReportedTime Stamp when this Rogue was Last Detected.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.14.1.4 |
bsnRogueClientBSSIDThis attribute specifies BSSID of the Rogue Client.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.14.1.5 |
bsnRogueClientContainmentLevelIf the state of the rogue is contained, this specifies the level of containment. Higher the level, more the number of detecting APs that are used to contain it. The value must be between 1 to 4 for 'contained' state.rw Enumeration .1.3.6.1.4.1.14179.2.1.14.1.6 |
bsnRogueClientLastHeardNumber of seconds ago this rogue client was detected.ro Integer32 .1.3.6.1.4.1.14179.2.1.14.1.7 |
bsnRogueClientStateThis attribute is use to specify the state in which the Rogue AP is. User can set the Rogue Client in alert,known or acknowledge state. Alert state means Rogue Client can be a potential i threat.Trap will be sent out to trap recipients. Known state means its just internal Client which is not on the same Switch. Acknowledge state means an external Client whose existence is acceptable and not a threat (probably some other company's AP). Contained means containement is initiated and ongoingrw Enumeration .1.3.6.1.4.1.14179.2.1.14.1.24 |
bsnRogueClientAirespaceAPTableRogue Station Table. This table lists all the Airespace AP Interface that detected a particular Rogue. SEQUENCE OF BsnRogueClientAirespaceAPEntry .1.3.6.1.4.1.14179.2.1.15 |
bsnRogueClientAirespaceAPEntryAn entry in bsnRogueClientAirespaceAPEntry. BsnRogueClientAirespaceAPEntry .1.3.6.1.4.1.14179.2.1.15.1 |
bsnRogueClientAirespaceAPMacAddressMac Address of Airespace AP Interface that Detected the Rogue.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.15.1.1 |
bsnRogueClientAirespaceAPSlotIdThe slotId of the Airespace AP Interface that detected the Rogue.ro Unsigned32 .1.3.6.1.4.1.14179.2.1.15.1.2 |
bsnRogueClientRadioTypeThe advertised SSID that the Airespace AP Interface picked up from the Rogue.ro Enumeration .1.3.6.1.4.1.14179.2.1.15.1.3 |
bsnRogueClientAirespaceAPNameName of Airespace AP Interface that detected the Rogue.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.15.1.4 |
bsnRogueClientChannelNumberThe advertised Channel Number of that the Airespace AP Interface picked up from the Rogue.ro Integer32 .1.3.6.1.4.1.14179.2.1.15.1.5 |
bsnRogueClientAirespaceAPRSSIRSSI seen by Airespace AP Interface from the Roguero Integer32 .1.3.6.1.4.1.14179.2.1.15.1.7 |
bsnRogueClientAirespaceAPLastHeardNo of seconds ago when this Rogue was last heard by this AP.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.15.1.11 |
bsnRogueClientAirespaceAPSNRSNR seen by Airespace AP Interface from Roguero Integer32 .1.3.6.1.4.1.14179.2.1.15.1.27 |
bsnRogueClientPerRogueAPTableRogue Clients for each rogue. This table lists all Rogue Clients on a particular Rogue. SEQUENCE OF BsnRogueClientPerRogueAPEntry .1.3.6.1.4.1.14179.2.1.16 |
bsnRogueClientPerRogueAPEntryAn entry in RogueClientPerRogueAPTable. BsnRogueClientPerRogueAPEntry .1.3.6.1.4.1.14179.2.1.16.1 |
bsnRogueAPDot11MacAddrThe MAC Address of the Rogue AP.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.16.1.1 |
bsnRogueClientDot11MacAddrMAC Address of the Rogue Client.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.16.1.20 |
bsnDot11QosProfileTableQOS Profiles specified in bsnDot11EssTable can be customized in this table. This is a lookup table for auto created profiles SEQUENCE OF BsnDot11QosProfileEntry .1.3.6.1.4.1.14179.2.1.17 |
bsnDot11QosProfileEntryAn entry in bsnDot11QosProfileTable. BsnDot11QosProfileEntry .1.3.6.1.4.1.14179.2.1.17.1 |
bsnDot11QosProfileNameQOS Profile Name. This will be one of bronze,gold, platinum,silver,uranium.ro OCTET STRING .1.3.6.1.4.1.14179.2.1.17.1.1 |
bsnDot11QosProfileDescQOS Profile Description.rw OCTET STRING .1.3.6.1.4.1.14179.2.1.17.1.2 |
bsnDot11QosAverageDataRateThis is one of the per user bandwidth contracts(k). Specifies Average Data Rate per user. Value of 0 indicates the feature is disabled.rw INTEGER .1.3.6.1.4.1.14179.2.1.17.1.3 |
bsnDot11QosBurstDataRateThis is one of the per user bandwidth contracts(k). Specifies Average Burst Data Rate per user. Value of 0 indicates the feature is disabled.rw INTEGER .1.3.6.1.4.1.14179.2.1.17.1.4 |
bsnDot11QosAvgRealTimeDataRateThis is one of the per user bandwidth contracts(k). Specifies Average Real Time Data Rate per user. Value of 0 indicates the feature is disabled.rw INTEGER .1.3.6.1.4.1.14179.2.1.17.1.5 |
bsnDot11QosBurstRealTimeDataRateThis is one of the per user bandwidth contracts(k). Specifies Burst Real Time Data Rate per user. Value of 0 indicates the feature is disabled.rw INTEGER .1.3.6.1.4.1.14179.2.1.17.1.6 |
bsnDot11QosMaxRFUsagePerAPThis is one of the over the Air QOS parameter. Specifies maximum RF Usage per AP in percentage.rw INTEGER .1.3.6.1.4.1.14179.2.1.17.1.7 |
bsnDot11QosProfileQueueDepthThis is one of the over the Air QOS parameter. Specifies Queue depth for the current profile.rw INTEGER .1.3.6.1.4.1.14179.2.1.17.1.8 |
bsnDot11WiredQosProtocolThis is one of the over the Air QOS parameter. Specifies Queue depth for the current profile.rw Enumeration .1.3.6.1.4.1.14179.2.1.17.1.9 |
bsnDot11802Dot1PTagSpecifies the type of wired QOS protocol for the current profile. Value of 0 indicates the feature is disabled.rw INTEGER .1.3.6.1.4.1.14179.2.1.17.1.10 |
bsnDot11ResetProfileToDefaultSet this attribute to reset to restore the factory default value for the profile.rw Enumeration .1.3.6.1.4.1.14179.2.1.17.1.40 |
bsnTagTableRF ID Tag Table indexed by bsnTagDot11MacAddress. SEQUENCE OF BsnTagEntry .1.3.6.1.4.1.14179.2.1.18 |
bsnTagEntryAn entry in bsnTagTable. BsnTagEntry .1.3.6.1.4.1.14179.2.1.18.1 |
bsnTagDot11MacAddress802.11 MAC Address of the RF ID Tag.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.18.1.1 |
bsnTagTypeType of the RF ID Tag.ro Enumeration .1.3.6.1.4.1.14179.2.1.18.1.2 |
bsnTagTimeIntervalTime Interval after which the tag transmits data.ro Unsigned32 .1.3.6.1.4.1.14179.2.1.18.1.3 |
bsnTagBatteryStatusBattery Status of the RF ID Tag.ro Enumeration .1.3.6.1.4.1.14179.2.1.18.1.4 |
bsnTagLastReportedNo of seconds ago when this tag was heard by any AP.ro Unsigned32 .1.3.6.1.4.1.14179.2.1.18.1.23 |
bsnTagRssiDataTableRF ID Tag Detecting AP Table indexed by bsnTagDot11MacAddress, bsnTagRssiDataApMacAddress and bsnTagRssiDataApIfSlotId. SEQUENCE OF BsnTagRssiDataEntry .1.3.6.1.4.1.14179.2.1.19 |
bsnTagRssiDataEntryAn entry in bsnTagRssiDataTable. BsnTagRssiDataEntry .1.3.6.1.4.1.14179.2.1.19.1 |
bsnTagRssiDataApMacAddress802.11 MAC Address of the AP detecting the RF ID Tag.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.1.19.1.1 |
bsnTagRssiDataApIfSlotIdSlot Id of the radio on AP detecting the RF ID Tag.ro Unsigned32 .1.3.6.1.4.1.14179.2.1.19.1.2 |
bsnTagRssiDataApIfTypeInterface Type of the radio on AP detecting the RF ID Tag.ro Enumeration .1.3.6.1.4.1.14179.2.1.19.1.3 |
bsnTagRssiDataApNameName of the AP detecting the RF ID Tag.ro DisplayString .1.3.6.1.4.1.14179.2.1.19.1.4 |
bsnTagRssiDataLastHeardNo of seconds ago when this tag was heard by this detecting AP.ro Counter32 .1.3.6.1.4.1.14179.2.1.19.1.5 |
bsnTagRssiDataRSSI of the RF ID Tag as seen by the radio on this detecting AP.ro Integer32 .1.3.6.1.4.1.14179.2.1.19.1.6 |
bsnTagRssiDataSnrSNR of the RF ID tag as seen by the radio on this detecting AP.ro Integer32 .1.3.6.1.4.1.14179.2.1.19.1.26 |
bsnTagStatsTableRF ID Tag Statistics Table. SEQUENCE OF BsnTagStatsEntry .1.3.6.1.4.1.14179.2.1.20 |
bsnTagStatsEntryAn entry in bsnTagStatsTable. BsnTagStatsEntry .1.3.6.1.4.1.14179.2.1.20.1 |
bsnTagBytesReceivedBytes received from an RF ID Tagro Unsigned32 .1.3.6.1.4.1.14179.2.1.20.1.1 |
bsnTagPacketsReceivedPackets received from an RF ID Tagro Unsigned32 .1.3.6.1.4.1.14179.2.1.20.1.20 |
bsnMobileStationExtStatsTableThis table was supported only by indoor mesh AP -cisco 1000. As this AP is not supported after 4.2.x.x. This table has been marked obsolete. Mobile Station Extended Statistics Table. (Mobile Station is better referred to as Client in the current releases.)obsolete SEQUENCE OF BsnMobileStationExtStatsEntry .1.3.6.1.4.1.14179.2.1.21 |
bsnMobileStationExtStatsEntryAn entry in bsnMobileStationExtStatsTable.obsolete BsnMobileStationExtStatsEntry .1.3.6.1.4.1.14179.2.1.21.1 |
bsnMobileStationSampleTimeTime stats were sampled as seconds since the epoch.roobsolete Integer32 .1.3.6.1.4.1.14179.2.1.21.1.1 |
bsnMobileStationTxExcessiveRetriesTx packets dropped due to excessive retries.roobsolete Counter64 .1.3.6.1.4.1.14179.2.1.21.1.2 |
bsnMobileStationTxRetriesTx packets retransmitted.roobsolete Counter64 .1.3.6.1.4.1.14179.2.1.21.1.3 |
bsnMobileStationTxFilteredTx packets dropped by the built-in Tx filterroobsolete Counter64 .1.3.6.1.4.1.14179.2.1.21.1.20 |
bsnAP OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.2 |
bsnAPTableTable of Airespace APs managed by this Airespace Switch. SEQUENCE OF BsnAPEntry .1.3.6.1.4.1.14179.2.2.1 |
bsnAPEntryAn entry in the bsnAPTable. BsnAPEntry .1.3.6.1.4.1.14179.2.2.1.1 |
bsnAPDot3MacAddressThe MAC address of an AP.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.2.1.1.1 |
bsnAPNumOfSlotsNumber of Radio Interfaces on the Airespace AP. Currently maximum two interfaces are supported. One would be of type 802.11a and other of type 802.11b/g.ro INTEGER .1.3.6.1.4.1.14179.2.2.1.1.2 |
bsnAPNameName assigned to this AP. If an AP is not configured its factory default name will be ap:<last three byte of MACAddress> eg. ap:af:12:berw OCTET STRING .1.3.6.1.4.1.14179.2.2.1.1.3 |
bsnAPLocationUser specified location of this AP. While configuring AP, user should specify a location for the AP so that its easy to figure out for some one where the AP is located.rw OCTET STRING .1.3.6.1.4.1.14179.2.2.1.1.4 |
bsnAPMonitorOnlyModeMonitor Only Mode Setting.rw Enumeration .1.3.6.1.4.1.14179.2.2.1.1.5 |
bsnAPOperationStatusOperation State of the AP. When AP associates with the Airespace Switch its state will be associated. When Airespace AP is disassociated from the Switch, its state will be disassociating. The state is downloading when the AP is downloading its firmware.ro Enumeration .1.3.6.1.4.1.14179.2.2.1.1.6 |
bsnAPSoftwareVersionMajor Minor Software Version of APro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.2.1.1.8 |
bsnAPBootVersionMajor Minor Boot Version of APro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.2.1.1.9 |
bsnAPPrimaryMwarNamesysName of the Airespace Switch which is suppose to be the Primary MWAR(switch) of the AP with which AP should associate. This work when AP is not directly connected to Airespace Switch, it tries to find Primary Switch and associates with it. If this attribute is left empty or AP is not able to find the Airespace Switch with this name, then it will associate with Secondary Switch.rw OCTET STRING .1.3.6.1.4.1.14179.2.2.1.1.10 |
bsnAPResetSet this attribute to reset the AP. When it comes up it will try to associate with the Primary Switch if that is set, else it will associate with the Master Switch. Reading this attribute will always return 0rw Enumeration .1.3.6.1.4.1.14179.2.2.1.1.11 |
bsnAPStatsTimerConfigures the time interval in secs after which bsnAPDot11Counters Stats is sent from AP to Switch. If not configured this value is 0 which means never send the stats.rw INTEGER .1.3.6.1.4.1.14179.2.2.1.1.12 |
bsnAPPortNumberPort on the Switch on which this APs traffic is coming through.ro INTEGER .1.3.6.1.4.1.14179.2.2.1.1.13 |
bsnAPModelAP Modelro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.2.1.1.16 |
bsnAPSerialNumberAP Serial Number.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.2.1.1.17 |
bsnAPClearConfigSet this attribute to clear AP configuration and reset it to factory defaults. Reading this attribute will always return 0rw Enumeration .1.3.6.1.4.1.14179.2.2.1.1.18 |
bsnApIpAddressIP address of the AP. This will not be available when the switch is operating in the Layer2 mode. In this case, the attribute will return 0 as value.rw IpAddress .1.3.6.1.4.1.14179.2.2.1.1.19 |
bsnAPMirrorModeIf enabled, then this AP's Client's Data is mirrored and this AP's clients are dynamically added to the switch's mirrored MAC list.rw Enumeration .1.3.6.1.4.1.14179.2.2.1.1.20 |
bsnAPRemoteModeSupportThis specifies if the the Remote Mode is supported on this AP or not. If supported user can set bsnAPMonitorOnlyMode to remote. Otherwise not.ro Enumeration .1.3.6.1.4.1.14179.2.2.1.1.21 |
bsnAPTypeThis is the model of the AP in enumeration.ro Enumeration .1.3.6.1.4.1.14179.2.2.1.1.22 |
bsnAPSecondaryMwarNamesysName of the Airespace Switch which is suppose to be the Secondary MWAR(switch) of the AP with which AP should associate if Primary Switch(configured through bsnAPPrimaryMwarName) is not available. If primary and secondary switches are not available then AP will associate with the tertiary switch.rw OCTET STRING .1.3.6.1.4.1.14179.2.2.1.1.23 |
bsnAPTertiaryMwarNamesysName of the Airespace Switch which is suppose to be the Tertiary MWAR(switch) of the AP with which AP should associate. If primary,secondary and tertiary switch are not available then it will associate with Master Switch.rw OCTET STRING .1.3.6.1.4.1.14179.2.2.1.1.24 |
bsnAPIsStaticIPThis flag when disabled implies that AP will use DHCP to get the IP address. However, if it is enabled, then user should enter the IPAddress, Netmask and Gateway.rw Enumeration .1.3.6.1.4.1.14179.2.2.1.1.25 |
bsnAPNetmaskThe Netmask of the IP address of the AP.rw IpAddress .1.3.6.1.4.1.14179.2.2.1.1.26 |
bsnAPGatewayThe Gateway for the AP.rw IpAddress .1.3.6.1.4.1.14179.2.2.1.1.27 |
bsnAPStaticIPAddressThe Static IP-Address configuration for the AP. This can only be changed when the LWAPP mode is in Layer-3.rw IpAddress .1.3.6.1.4.1.14179.2.2.1.1.28 |
bsnAPBridgingSupportThis specifies if this AP is a Bridging AP. Bridging APs can be used in Bridging or Mesh network configurations.rw Enumeration .1.3.6.1.4.1.14179.2.2.1.1.29 |
bsnAPGroupVlanNameThe AP Group to which this AP has been associated with. If it is empty, then no AP Group overriding has been set.rw OCTET STRING .1.3.6.1.4.1.14179.2.2.1.1.30 |
bsnAPIOSVersionIOS Version of IOS Cisco AP. Zero length string will be returned for other APsro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.2.1.1.31 |
bsnAPCertificateTypeEnum values denoting AP Certificate Type. 1 : manufactureinstalled : Manufacture Installed Certificate type (MIC). 2 : selfsigned : Self Signed Certificate type (SSC). 3 : localsignificance : Local Significance.ro Enumeration .1.3.6.1.4.1.14179.2.2.1.1.32 |
bsnAPEthernetMacAddressThe Ethernet MAC address of the AP.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.2.1.1.33 |
bsnAPAdminStatusAdmin State of the APrw Enumeration .1.3.6.1.4.1.14179.2.2.1.1.37 |
bsnAPIfTableEach entry represents an 802.11 interface in an Airespace AP. SEQUENCE OF BsnAPIfEntry .1.3.6.1.4.1.14179.2.2.2 |
bsnAPIfEntryAn entry in bsnAPIfTable. BsnAPIfEntry .1.3.6.1.4.1.14179.2.2.2.1 |
bsnAPIfSlotIdThe slotId of this interface.ro Unsigned32 .1.3.6.1.4.1.14179.2.2.2.1.1 |
bsnAPIfTypeThe type of this interface. dot11b also implies 802.11b/g.ro Enumeration .1.3.6.1.4.1.14179.2.2.2.1.2 |
bsnAPIfPhyChannelAssignmentIf this value is true, then bsnAPDot11CurrentChannel in bsnAPIfDot11PhyDSSSTable is assigned by dynamic algorithm and is read-only.rw Enumeration .1.3.6.1.4.1.14179.2.2.2.1.3 |
bsnAPIfPhyChannelNumberCurrent channel number of the AP Interface. Channel numbers will be from 1 to 14 for 802.11b interface type. Channel numbers will be from 34 to 169 for 802.11a interface type. Allowed channel numbers also depends on the current Country Code set in the Switch. This attribute cannot be set unless bsnAPIfPhyChannelAssignment is set to customized else this attribute gets assigned by dynamic algorithm.rw Enumeration .1.3.6.1.4.1.14179.2.2.2.1.4 |
bsnAPIfPhyTxPowerControlIf this value is true, then bsnAPIfPhyTxPowerLevel is assigned by dynamic algorithm and is read-only.rw Enumeration .1.3.6.1.4.1.14179.2.2.2.1.5 |
bsnAPIfPhyTxPowerLevelThe TxPowerLevel currently being used to transmit data. Some PHYs also use this value to determine the receiver sensitivity requirements for CCA. Valid values are between 1 to 8,depnding on what radio, and this attribute can be set only if bsnAPIfPhyTxPowerControl is set to customized.rw INTEGER .1.3.6.1.4.1.14179.2.2.2.1.6 |
bsnAPIfPhyAntennaModeAntenna Mode of the AP Interface. For 802.11a this attribute will always be omni for now. This attribute doesn't apply to interface of type 802.11b.rw Enumeration .1.3.6.1.4.1.14179.2.2.2.1.7 |
bsnAPIfPhyAntennaTypeThis attribute specified if the Antenna currently used by AP Radio is internal or external. For 802.11a the antenna is always internal. For 802.11b you can set antenna type to be external or internal.rw Enumeration .1.3.6.1.4.1.14179.2.2.2.1.8 |
bsnAPIfPhyAntennaDiversityDiversity doesn't apply to AP Radio of type 802.11a. For 802.11b you can set it to connectorA, connectorB or enabled.rw Enumeration .1.3.6.1.4.1.14179.2.2.2.1.9 |
bsnAPIfCellSiteConfigIdIn a cell site configuration, this would be the cell Id of this AP Interfacerw Unsigned32 .1.3.6.1.4.1.14179.2.2.2.1.10 |
bsnAPIfNumberOfVapsNumber of WLANs currently active on this AP Interface.ro INTEGER .1.3.6.1.4.1.14179.2.2.2.1.11 |
bsnAPIfOperStatusOperational status of the interface.ro Enumeration .1.3.6.1.4.1.14179.2.2.2.1.12 |
bsnAPIfPortNumberPort number on Airespace Switch on which the traffic from this AP interface is received.ro INTEGER .1.3.6.1.4.1.14179.2.2.2.1.13 |
bsnAPIfPhyAntennaOptionsThis attribute specifies the Antenna types supported by the AP Radio whether it is internal or external or both. internalAndExternal(0)- internal and external antenna for both 11a and 11b internal(1) - only internal antenna is allowed. siacAp- 11b internal and 11a external external - only external antenna is allowed for 11a and 11b ext11bInt11a - external antenna for 11b and internal antenna for 11a.ro Enumeration .1.3.6.1.4.1.14179.2.2.2.1.14 |
bsnApIfNoOfUsersNo of Users associated with this radio.ro Counter32 .1.3.6.1.4.1.14179.2.2.2.1.15 |
bsnAPIfWlanOverrideThis flag when disabled implies that all WLANs are available from this radio. However, if this is enabled, then only those WLANs that appear in the bsnApIfWlanOverrideTable will be available from this radio.rw Enumeration .1.3.6.1.4.1.14179.2.2.2.1.16 |
bsnAPIfPacketsSniffingFeatureThis flag when enabled implies that AP will sniff the 802.11a/bg packets. However, if it is enabled, then user should enter the server-ip-address on which Airopeek is running and the 802.11a/bg-channel-number to be sniffed. The above feature will work only when AP is in 'Sniffer' mode.rw Enumeration .1.3.6.1.4.1.14179.2.2.2.1.17 |
bsnAPIfSniffChannelThis the 802.11a/bg-channel-number on which AP will sniff the packets.rw Enumeration .1.3.6.1.4.1.14179.2.2.2.1.18 |
bsnAPIfSniffServerIPAddressThe machine ip address on which Airopeek application is running.rw IpAddress .1.3.6.1.4.1.14179.2.2.2.1.19 |
bsnAPIfAntennaGainRepresents antenna gain in multiple of 0.5 dBm. An integer value 4 means 4 x 0.5 = 2 dBm of gainrw INTEGER .1.3.6.1.4.1.14179.2.2.2.1.20 |
bsnAPIfChannelListList of comma separated channels supported by this radio.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.2.2.1.21 |
bsnAPIfAbsolutePowerListList of comma separated absolute power levels supported by this radio.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.2.2.1.22 |
bsnAPIfRegulatoryDomainSupportIf the regulatory domain on radio is supported or notSupported on the controllerro Enumeration .1.3.6.1.4.1.14179.2.2.2.1.23 |
bsnAPIfAdminStatusAdmin status of the interface.rw Enumeration .1.3.6.1.4.1.14179.2.2.2.1.34 |
bsnAPIfSmtParamTableEach entry represents SMT parameters on an 802.11 interface of an Airespace AP. SEQUENCE OF BsnAPIfSmtParamEntry .1.3.6.1.4.1.14179.2.2.3 |
bsnAPIfSmtParamEntryAn entry in bsnAPIfSmtParamTable BsnAPIfSmtParamEntry .1.3.6.1.4.1.14179.2.2.3.1 |
bsnAPIfDot11BeaconPeriodThis attribute shall specify the number of TU that a AP Interface shall use for scheduling Beacon tranmissions. This value is transmitted in Beacon and Probe Response frames.ro INTEGER .1.3.6.1.4.1.14179.2.2.3.1.1 |
bsnAPIfDot11MediumOccupancyLimitThis attribute shall indicate the maximum amount of time, in TU, that a point coordinator may control the usage of the wireless medium without relinquishing control for long enough to allow at least one instance of DCF access to the medium. The default value of this attribute shall be 100, and the maximum value shall be 1000.ro INTEGER .1.3.6.1.4.1.14179.2.2.3.1.2 |
bsnAPIfDot11CFPPeriodThe attribute shall describe the number of DTIM intervals between the start of CFPs. It is modified by MLME-START.request primitive.ro INTEGER .1.3.6.1.4.1.14179.2.2.3.1.3 |
bsnAPIfDot11CFPMaxDurationThe attribute shall describe the maximum duration of the CFP in TU that may be generated by the PCF. It is modified by MLME-START.request primitive.ro INTEGER .1.3.6.1.4.1.14179.2.2.3.1.4 |
bsnAPIfDot11OperationalRateSetThis attribute shall specify the set of data rates at which the AP Interface may transmit data. Each octet contains a value representing a rate. Each rate shall be within the range from 2 to 127, corresponding to data rates in increments of 500 kb/s from 1 Mb/s to 63.5 Mb/s, and shall be supported (as indicated in the supported rates table) for receiving data. This value is reported in transmitted Beacon, Probe Request, Probe Response, Association Request, Association Response, Reassociation Request, and Reassociation Response frames, and is used to determine whether a BSS with which the AP Interface desires to synchronize is suitable. It is also used when starting a BSS, as specified in 10.3.ro OCTET STRING .1.3.6.1.4.1.14179.2.2.3.1.5 |
bsnAPIfDot11DTIMPeriodThis attribute shall specify the number of beacon intervals that shall elapse between transmission of Beacons frames containing a TIM element whose DTIM Count field is 0. This value is transmitted in the DTIM Period field of Beacon frames.ro INTEGER .1.3.6.1.4.1.14179.2.2.3.1.6 |
bsnAPIfDot11MultiDomainCapabilityImplementedThis attribute, when TRUE, indicates that the AP Interface implementation is capable of supporting multiple regulatory domains. The capability is disabled, otherwise. The default value of this attribute is FALSE.ro Enumeration .1.3.6.1.4.1.14179.2.2.3.1.7 |
bsnAPIfDot11MultiDomainCapabilityEnabledThis attribute, when TRUE, indicates that the capability of the AP Interface to operate in multiple regulatory domains is enabled. The capability is disabled, otherwise. The default value of this attribute is FALSE.ro Enumeration .1.3.6.1.4.1.14179.2.2.3.1.8 |
bsnAPIfDot11CountryStringThis attribute identifies the country in which the AP Interface is operating. The first two octets of this string is the two character country code as described in document ISO/IEC 3166-1. The third octet shall be one of the following: 1. an ASCII space character, if the regulations under which the AP Interface is operating encompass all environments in the country, 2. an ASCII 'O' character, if the regulations under which the AP Interface is operating are for an Outdoor environment only, or 3. an ASCII 'I' character, if the regulations under which the AP Interface is operating are for an Indoor environment only.ro OCTET STRING .1.3.6.1.4.1.14179.2.2.3.1.9 |
bsnAPIfDot11SmtParamsConfigTypeThis attribute suggests if the Station parameters for this radio are automatically set or have been customized.ro Enumeration .1.3.6.1.4.1.14179.2.2.3.1.10 |
bsnAPIfDot11BSSIDBSSID of this AP config which would be the MAC Address of APro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.2.3.1.30 |
bsnAPIfMultiDomainCapabilityTableEach entry represents an 803.2 or an 802.11 interface in an Airespace AP. SEQUENCE OF BsnAPIfMultiDomainCapabilityEntry .1.3.6.1.4.1.14179.2.2.4 |
bsnAPIfMultiDomainCapabilityEntryEach entry represents an 803.2 or an 802.11 interface in an Airespace AP. BsnAPIfMultiDomainCapabilityEntry .1.3.6.1.4.1.14179.2.2.4.1 |
bsnAPIfDot11MaximumTransmitPowerLevelThis attribute shall indicate the maximum transmit power, in dBm, allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.ro Integer32 .1.3.6.1.4.1.14179.2.2.4.1.1 |
bsnAPIfDot11FirstChannelNumberThis attribute shall indicate the value of the lowest channel number in the subband for the associated domain country string. The default value of this attribute shall be zero.ro Integer32 .1.3.6.1.4.1.14179.2.2.4.1.2 |
bsnAPIfDot11NumberofChannelsThis attribute shall indicate the value of the total number of channels allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.ro Integer32 .1.3.6.1.4.1.14179.2.2.4.1.20 |
bsnAPIfMacOperationParamTableGroup contains MAC attributes pertaining to the operation of the MAC. These would be read only attributes as they would be updated by RRM Dynamic Algorithm. If user needs to configure them then they can only be configured globally SEQUENCE OF BsnAPIfMacOperationParamEntry .1.3.6.1.4.1.14179.2.2.5 |
bsnAPIfMacOperationParamEntryAn entry in the bsnAPIfMacOperationParamEntry Table. Interface tables in this MIB module are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId. BsnAPIfMacOperationParamEntry .1.3.6.1.4.1.14179.2.2.5.1 |
bsnAPIfDot11MacRTSThresholdIf bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithmro INTEGER .1.3.6.1.4.1.14179.2.2.5.1.1 |
bsnAPIfDot11MacShortRetryLimitIf bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithmro INTEGER .1.3.6.1.4.1.14179.2.2.5.1.2 |
bsnAPIfDot11MacLongRetryLimitIf bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithmro INTEGER .1.3.6.1.4.1.14179.2.2.5.1.3 |
bsnAPIfDot11MacFragmentationThresholdIf bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithmro INTEGER .1.3.6.1.4.1.14179.2.2.5.1.4 |
bsnAPIfDot11MacMaxTransmitMSDULifetimeIf bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithmro Unsigned32 .1.3.6.1.4.1.14179.2.2.5.1.5 |
bsnAPIfDot11MacParamsConfigTypeThis attribute suggests if the MAC parameters for this radio are automatically set or have been customized.ro Enumeration .1.3.6.1.4.1.14179.2.2.5.1.6 |
bsnAPIfDot11MacMaxReceiveLifetimeIf bsnAPIfMacParamsAutomaticOn is true then this is read only parameter updated by RRM dynamic algorithmro Unsigned32 .1.3.6.1.4.1.14179.2.2.5.1.25 |
bsnAPIfDot11CountersTableGroup containing attributes that are MAC counters. Each instance represents counters on a AP dot11 interface SEQUENCE OF BsnAPIfDot11CountersEntry .1.3.6.1.4.1.14179.2.2.6 |
bsnAPIfDot11CountersEntryAn entry in the dot11CountersEntry Table. Interface tables in this MIB module are indexed by bsnAPDot3MacAddress and bsnAPIfSlotId BsnAPIfDot11CountersEntry .1.3.6.1.4.1.14179.2.2.6.1 |
bsnAPIfDot11TransmittedFragmentCountThis counter shall be incremented for an acknowledged MPDU with an individual address in the address 1 field or an MPDU with a multicast address in the address 1 field of type Data or Management.ro Counter32 .1.3.6.1.4.1.14179.2.2.6.1.1 |
bsnAPIfDot11MulticastTransmittedFrameCountThis counter shall increment only when the multicast bit is set in the destination MAC address of a successfully transmitted MSDU. When operating as a STA in an ESS, where these frames are directed to the AP, this implies having received an acknowledgment to all associated MPDUs.ro Counter32 .1.3.6.1.4.1.14179.2.2.6.1.2 |
bsnAPIfDot11RetryCountThis counter shall increment when an MSDU is successfully transmitted after one or more retransmissions.ro Counter32 .1.3.6.1.4.1.14179.2.2.6.1.3 |
bsnAPIfDot11MultipleRetryCountThis counter shall increment when an MSDU is successfully transmitted after more than one retransmission.ro Counter32 .1.3.6.1.4.1.14179.2.2.6.1.4 |
bsnAPIfDot11FrameDuplicateCountThis counter shall increment when a frame is received that the Sequence Control field indicates is a duplicate.ro Counter32 .1.3.6.1.4.1.14179.2.2.6.1.5 |
bsnAPIfDot11RTSSuccessCountThis counter shall increment when a CTS is received in response to an RTS.ro Counter32 .1.3.6.1.4.1.14179.2.2.6.1.6 |
bsnAPIfDot11RTSFailureCountThis counter shall increment when a CTS is not received in response to an RTS.ro Counter32 .1.3.6.1.4.1.14179.2.2.6.1.7 |
bsnAPIfDot11ACKFailureCountThis counter shall increment when an ACK is not received when expected.ro Counter32 .1.3.6.1.4.1.14179.2.2.6.1.8 |
bsnAPIfDot11ReceivedFragmentCountThis counter shall be incremented for each successfully received MPDU of type Data or Management.ro Counter32 .1.3.6.1.4.1.14179.2.2.6.1.9 |
bsnAPIfDot11MulticastReceivedFrameCountThis counter shall increment when a MSDU is received with the multicast bit set in the destination MAC address.ro Counter32 .1.3.6.1.4.1.14179.2.2.6.1.10 |
bsnAPIfDot11FCSErrorCountThis counter shall increment when an FCS error is detected in a received MPDU.ro Counter32 .1.3.6.1.4.1.14179.2.2.6.1.11 |
bsnAPIfDot11TransmittedFrameCountThis counter shall increment for each successfully transmitted MSDU.ro Counter32 .1.3.6.1.4.1.14179.2.2.6.1.12 |
bsnAPIfDot11WEPUndecryptableCountThis counter shall increment when a frame is received with the WEP subfield of the Frame Control field set to one and the WEPOn value for the key mapped to the TA's MAC address indicates that the frame should not have been encrypted or that frame is discarded due to the receiving STA not implementing the privacy option.ro Counter32 .1.3.6.1.4.1.14179.2.2.6.1.13 |
bsnAPIfDot11FailedCountThis counter shall increment when an MSDU is not transmitted successfully due to the number of transmit attempts exceeding either the bsnAPIfDot11ShortRetryLimit or dot11LongRetryLimit.ro Counter32 .1.3.6.1.4.1.14179.2.2.6.1.33 |
bsnAPIfDot11PhyTxPowerTableGroup of attributes for bsnAPIfDot11PhyTxPowerTable. Implemented as a table indexed on STA ID to allow for multiple instances on an Agent. This table has been deprecated. The level and power can be obtained from bsnAPIfTable(bsnAPIfAbsolutePowerList).deprecated SEQUENCE OF BsnAPIfDot11PhyTxPowerEntry .1.3.6.1.4.1.14179.2.2.8 |
bsnAPIfDot11PhyTxPowerEntryAn entry in the bsnAPIfDot11PhyTxPower Table. Interface tables in this MIB module are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId.deprecated BsnAPIfDot11PhyTxPowerEntry .1.3.6.1.4.1.14179.2.2.8.1 |
bsnAPIfDot11NumberSupportedPowerLevelsThe number of power levels supported by the PMD. This attribute can have a value of 1 to 8.rodeprecated INTEGER .1.3.6.1.4.1.14179.2.2.8.1.1 |
bsnAPIfDot11TxPowerLevel1The transmit output power for LEVEL1 in mW. This is also the default power level. It is same as the Maximum power level available on an AP interface.rodeprecated INTEGER .1.3.6.1.4.1.14179.2.2.8.1.2 |
bsnAPIfDot11TxPowerLevel2The transmit output power for LEVEL2 in mW. It is 1/2 of the Maximum power level available on an AP interface.rodeprecated INTEGER .1.3.6.1.4.1.14179.2.2.8.1.3 |
bsnAPIfDot11TxPowerLevel3The transmit output power for LEVEL3 in mW. It is 1/4th of the Maximum power level available on an AP interface.rodeprecated INTEGER .1.3.6.1.4.1.14179.2.2.8.1.4 |
bsnAPIfDot11TxPowerLevel4The transmit output power for LEVEL4 in mW. It is 1/8th of the Maximum power level available on an AP interface.rodeprecated INTEGER .1.3.6.1.4.1.14179.2.2.8.1.5 |
bsnAPIfDot11TxPowerLevel5The transmit output power for LEVEL5 in mW. It is 1/16th of the Maximum power level available on an AP interface.rodeprecated INTEGER .1.3.6.1.4.1.14179.2.2.8.1.6 |
bsnAPIfDot11TxPowerLevel6The transmit output power for LEVEL6 in mW. It is 1/32th of the Maximum power level available on an AP interface.rodeprecated INTEGER .1.3.6.1.4.1.14179.2.2.8.1.7 |
bsnAPIfDot11TxPowerLevel7The transmit output power for LEVEL7 in mW. It is 1/64th of the Maximum power level available on an AP interface.rodeprecated INTEGER .1.3.6.1.4.1.14179.2.2.8.1.8 |
bsnAPIfDot11TxPowerLevel8The transmit output power for LEVEL8 in mW. It is 1/128th of the Maximum power level available on an AP interface.rodeprecated INTEGER .1.3.6.1.4.1.14179.2.2.8.1.28 |
bsnAPIfDot11PhyChannelTableEntry of attributes for bsnAPIfDot11PhyChannelEntry. Implemented as a table indexed on bsnAPDot3MacAddress, bsnAPIfSlotId allow for multiple instances on an Agent SEQUENCE OF BsnAPIfDot11PhyChannelEntry .1.3.6.1.4.1.14179.2.2.9 |
bsnAPIfDot11PhyChannelEntryAn entry in the bsnAPIfDot11PhyChannelEntry Table. Interface tables in this MIB module are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId. BsnAPIfDot11PhyChannelEntry .1.3.6.1.4.1.14179.2.2.9.1 |
bsnAPIfDot11CurrentCCAModeThe current CCA method in operation.Valid values are: energy detect only (edonly) = 01, carrier sense only (csonly) = 02, carrier sense and energy detect (edandcs)= 04 carrier sense with timer (cswithtimer)= 08 high rate carrier sense and energy detect (hrcsanded)=16.ro Enumeration .1.3.6.1.4.1.14179.2.2.9.1.1 |
bsnAPIfDot11EDThresholdThe current Energy Detect Threshold being used by the Channel PHY.ro Integer32 .1.3.6.1.4.1.14179.2.2.9.1.2 |
bsnAPIfDot11TIThresholdThe Threshold being used to detect a busy medium (frequency). CCA shall report a busy medium upon detecting the RSSI above this threshold.ro Integer32 .1.3.6.1.4.1.14179.2.2.9.1.23 |
bsnAPIfProfileThresholdConfigTableTable of attributes for various thresholds to be set on each Airespace AP Interface for Load performance profile , interference performance profile and Noise performance profile. SEQUENCE OF BsnAPIfProfileThresholdConfigEntry .1.3.6.1.4.1.14179.2.2.12 |
bsnAPIfProfileThresholdConfigEntryAn entry (conceptual row) in the Phy Thresholds Table. Entries in this MIB are indexed by bsnAPDot3MacAddress and bsnAPIfSlotId BsnAPIfProfileThresholdConfigEntry .1.3.6.1.4.1.14179.2.2.12.1 |
bsnAPIfProfileParamAssignmentIf this value is automatic then Profile Parameters in bsnRrmDot11aAPProfile at the global level will be used. If this value is customized then Profile Parameters in bsnAPIfProfileThresholdConfig Table will be used and user can customize them per AP.rw Enumeration .1.3.6.1.4.1.14179.2.2.12.1.1 |
bsnAPIfForeignInterferenceThresholdforeign interference threshold between 0 and 100 percent.rw INTEGER .1.3.6.1.4.1.14179.2.2.12.1.2 |
bsnAPIfForeignNoiseThresholdforeign noise threshold between -100 and -50 dBm.rw INTEGER (-127..0) .1.3.6.1.4.1.14179.2.2.12.1.3 |
bsnAPIfRFUtilizationThresholdRF utlization threshold between 0 and 100 percent.rw INTEGER .1.3.6.1.4.1.14179.2.2.12.1.4 |
bsnAPIfThroughputThresholdAirespace AP data-rate threshold between 1000 and 100000rw Unsigned32 .1.3.6.1.4.1.14179.2.2.12.1.5 |
bsnAPIfMobilesThresholdAirespace AP mobiles threshold between 1 and 75rw INTEGER .1.3.6.1.4.1.14179.2.2.12.1.6 |
bsnAPIfCoverageThresholdAirespace AP coverage threshold between 3 and 50rw INTEGER .1.3.6.1.4.1.14179.2.2.12.1.7 |
bsnAPIfMobileMinExceptionLevelAirespace AP mobile minimum exception level between 1 and 1000rw INTEGER .1.3.6.1.4.1.14179.2.2.12.1.8 |
bsnAPIfCoverageExceptionLevelAirespace AP coverage exception level between 0 and 100 percent.rw INTEGER .1.3.6.1.4.1.14179.2.2.12.1.28 |
bsnAPIfLoadParametersTableThese are RRM performance related read only parameters per Airespace AP SEQUENCE OF BsnAPIfLoadParametersEntry .1.3.6.1.4.1.14179.2.2.13 |
bsnAPIfLoadParametersEntryAn entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress and bsnAPIfSlotId BsnAPIfLoadParametersEntry .1.3.6.1.4.1.14179.2.2.13.1 |
bsnAPIfLoadRxUtilizationThis is the percentage of time the Airespace AP receiver is busy operating on packets. It is a number from 0-100 representing a load from 0 to 1.ro INTEGER .1.3.6.1.4.1.14179.2.2.13.1.1 |
bsnAPIfLoadTxUtilizationThis is the percentage of time the Airespace AP transmitter is busy operating on packets. It is a number from 0-100 representing a load from 0 to 1.ro INTEGER .1.3.6.1.4.1.14179.2.2.13.1.2 |
bsnAPIfLoadChannelUtilizationChannel Utilizationro INTEGER .1.3.6.1.4.1.14179.2.2.13.1.3 |
bsnAPIfLoadNumOfClientsThis is the number of clients attached to this Airespace AP at the last measurement interval(This comes from APF)ro Integer32 .1.3.6.1.4.1.14179.2.2.13.1.4 |
bsnAPIfPoorSNRClientsThis is the number of clients with poor SNR attached to this Airespace AP at the last measurement interval ( This comes from APF ).ro Integer32 .1.3.6.1.4.1.14179.2.2.13.1.24 |
bsnAPIfChannelInterferenceInfoTableThis is a table of channel information like interference and noise from other 802.11 networks on each channel. SEQUENCE OF BsnAPIfChannelInterferenceInfoEntry .1.3.6.1.4.1.14179.2.2.14 |
bsnAPIfChannelInterferenceInfoEntryAn entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId BsnAPIfChannelInterferenceInfoEntry .1.3.6.1.4.1.14179.2.2.14.1 |
bsnAPIfInterferenceChannelNoChannel Number on APro Integer32 .1.3.6.1.4.1.14179.2.2.14.1.1 |
bsnAPIfInterferencePowerPower of Interference from other 802.11 networks on this channelro Integer32 .1.3.6.1.4.1.14179.2.2.14.1.2 |
bsnAPIfInterferenceUtilizationInterference from other 802.11 networks on this channelro INTEGER .1.3.6.1.4.1.14179.2.2.14.1.22 |
bsnAPIfChannelNoiseInfoTableThis is a table of channel information like interference and noise from other 802.11 networks on each channel. SEQUENCE OF BsnAPIfChannelNoiseInfoEntry .1.3.6.1.4.1.14179.2.2.15 |
bsnAPIfChannelNoiseInfoEntryAn entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId BsnAPIfChannelNoiseInfoEntry .1.3.6.1.4.1.14179.2.2.15.1 |
bsnAPIfNoiseChannelNoChannel Number on APro Integer32 .1.3.6.1.4.1.14179.2.2.15.1.1 |
bsnAPIfDBNoisePowerThis is the average noise power in dBm on each channel that is available to Airespace APro Integer32 .1.3.6.1.4.1.14179.2.2.15.1.21 |
bsnAPIfProfileStateTableThis is a table of state of interference monitor on each Airespace AP SEQUENCE OF BsnAPIfProfileStateEntry .1.3.6.1.4.1.14179.2.2.16 |
bsnAPIfProfileStateEntryAn entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId BsnAPIfProfileStateEntry .1.3.6.1.4.1.14179.2.2.16.1 |
bsnAPIfLoadProfileStateThis field represents the current state of the LOAD monitor. This is a total measurement of the business of this Airespace AP. PASS indicates that this Airespace AP is performing adequately compared to the Airespace AP profile. FAIL indicates the Airespace AP is not performing adequately against the LOAD profile.ro ProfileState .1.3.6.1.4.1.14179.2.2.16.1.1 |
bsnAPIfInterferenceProfileStateThis field represents the current state of Interference monitor. This is a total measurement of the interference present at this Airespace AP. PASS indicates that this Airespace AP is performing adequately compared to the Interference profile. FAIL indicates the Airespace AP is not performing adequately against the Interference profile.ro ProfileState .1.3.6.1.4.1.14179.2.2.16.1.2 |
bsnAPIfNoiseProfileStateThis field represents the current state of Noise monitor. This is a total measurement of the noise present at this Airespace AP. PASS indicates that this Airespace AP is performing adequately compared to the noise profile. FAIL indicates the Airespace AP is not performing adequately against the noise profile.ro ProfileState .1.3.6.1.4.1.14179.2.2.16.1.3 |
bsnAPIfCoverageProfileStateThis field represents the current state of coverage monitor. This is a total measurement of the client coverage at this Airespace AP. PASS indicates that this Airespace AP is performing adequately compared to the coverage profile. FAIL indicates the Airespace AP is not performing adequately against the coverage profile.ro ProfileState .1.3.6.1.4.1.14179.2.2.16.1.24 |
bsnAPIfRxNeighborsTableThis is a table of Rx Neighbors for each Airespace AP with their RSSI value. SEQUENCE OF BsnAPIfRxNeighborsEntry .1.3.6.1.4.1.14179.2.2.17 |
bsnAPIfRxNeighborsEntryAn entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress bsnAPIfSlotId, bsnAPIfRxNeighborMacAddress BsnAPIfRxNeighborsEntry .1.3.6.1.4.1.14179.2.2.17.1 |
bsnAPIfRxNeighborMacAddressMAC Address of Rx Neighbor of the Airespace APro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.2.17.1.1 |
bsnAPIfRxNeighborIpAddressIP Address of Rx Neighbor of the Airespace APro IpAddress .1.3.6.1.4.1.14179.2.2.17.1.2 |
bsnAPIfRxNeighborRSSIRSSI value of the Rx Neighborro Integer32 .1.3.6.1.4.1.14179.2.2.17.1.3 |
bsnAPIfRxNeighborSlotSlot value of the Rx Neighborro Integer32 .1.3.6.1.4.1.14179.2.2.17.1.24 |
bsnAPIfRxNeighborChannelThis object represents Channel information which neighboring Access point is using.ro Integer32 .1.3.6.1.4.1.14179.2.2.17.1.26 |
bsnAPIfRxNeighborChannelWidthThis object represents Channel bandwidth information which neighboring Access point is using.ro Enumeration .1.3.6.1.4.1.14179.2.2.17.1.27 |
bsnAPIfStationRSSICoverageInfoTableThis is a table of channel information like interference and noise from other 802.11 networks on each channel. SEQUENCE OF BsnAPIfStationRSSICoverageInfoEntry .1.3.6.1.4.1.14179.2.2.18 |
bsnAPIfStationRSSICoverageInfoEntryAn entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId BsnAPIfStationRSSICoverageInfoEntry .1.3.6.1.4.1.14179.2.2.18.1 |
bsnAPIfStationRSSICoverageIndexRSSI Coverage Index on APro Integer32 .1.3.6.1.4.1.14179.2.2.18.1.1 |
bsnAPIfRSSILevelRSSI Levelro Integer32 .1.3.6.1.4.1.14179.2.2.18.1.2 |
bsnAPIfStationCountOnRSSINumber of stations on this RSSI Levelro Integer32 .1.3.6.1.4.1.14179.2.2.18.1.23 |
bsnAPIfStationSNRCoverageInfoTableThis is a table of Signal to Noise ratio Coverage information on an AP Interface. SEQUENCE OF BsnAPIfStationSNRCoverageInfoEntry .1.3.6.1.4.1.14179.2.2.19 |
bsnAPIfStationSNRCoverageInfoEntryAn entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId BsnAPIfStationSNRCoverageInfoEntry .1.3.6.1.4.1.14179.2.2.19.1 |
bsnAPIfStationSNRCoverageIndexSNR Coverage Index on APro Integer32 .1.3.6.1.4.1.14179.2.2.19.1.1 |
bsnAPIfSNRLevelSNR Levelro Integer32 .1.3.6.1.4.1.14179.2.2.19.1.2 |
bsnAPIfStationCountOnSNRNumber of stations on this SNR Levelro Integer32 .1.3.6.1.4.1.14179.2.2.19.1.23 |
bsnAPIfRecommendedRFParametersTableThis table list Best Channel,Best TxPowerLevel, Best RTSThreshold,Best FragmentationThreshold etc for this AP Interface as determined by RRM. SEQUENCE OF BsnAPIfRecommendedRFParametersEntry .1.3.6.1.4.1.14179.2.2.20 |
bsnAPIfRecommendedRFParametersEntryAn entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId BsnAPIfRecommendedRFParametersEntry .1.3.6.1.4.1.14179.2.2.20.1 |
bsnAPIfRecommendedChannelNumberRecommended ChannelNumber by RRM for this APIfro Integer32 .1.3.6.1.4.1.14179.2.2.20.1.1 |
bsnAPIfRecommendedTxPowerLevelRecommended TxPowerLevel by RRM for this APIfro Integer32 .1.3.6.1.4.1.14179.2.2.20.1.2 |
bsnAPIfRecommendedRTSThresholdRecommended RTSThreshold by RRM for this APIfro Integer32 .1.3.6.1.4.1.14179.2.2.20.1.3 |
bsnAPIfRecommendedFragmentationThresholdRecommended Fragmentation Threshold by RRM for this APIfro Integer32 .1.3.6.1.4.1.14179.2.2.20.1.24 |
bsnAPIfWlanOverrideTableEach entry represents an SSID added to the AP when the attribute bsnAPIfWlanOverride on the radio is enabled. This means only those WLANs on the switch that are added to this table will be available on such a radio. SEQUENCE OF BsnAPIfWlanOverrideEntry .1.3.6.1.4.1.14179.2.2.21 |
bsnAPIfWlanOverrideEntryAn entry in bsnAPIfWlanOverrideTable BsnAPIfWlanOverrideEntry .1.3.6.1.4.1.14179.2.2.21.1 |
bsnAPIfWlanOverrideIdIndex of the WLAN (bsnDot11EssIndex) added to the radio. Airespace Switch supports 16 Airespace WLANs so index will be from 1 to 16.rw Unsigned32 .1.3.6.1.4.1.14179.2.2.21.1.1 |
bsnAPIfWlanOverrideSsidSSID assigned to the override WLAN.ro DisplayString .1.3.6.1.4.1.14179.2.2.21.1.2 |
bsnAPIfWlanOverrideRowStatusA row status type for the bsnAPIfWlanOverrideEntryrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.2.21.1.15 |
bsnMeshNodeTableThis is a table of mesh nodes. SEQUENCE OF BsnMeshNodeEntry .1.3.6.1.4.1.14179.2.2.22 |
bsnMeshNodeEntryAn entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress BsnMeshNodeEntry .1.3.6.1.4.1.14179.2.2.22.1 |
bsnMeshNodeRolethe role of this APro Enumeration .1.3.6.1.4.1.14179.2.2.22.1.1 |
bsnMeshNodeGroupthe bridge group name of this APro OCTET STRING .1.3.6.1.4.1.14179.2.2.22.1.2 |
bsnMeshNodeBackhaulthe backhaul radio device for this APro Enumeration .1.3.6.1.4.1.14179.2.2.22.1.3 |
bsnMeshNodeBackhaulPAPthe backhaulro Enumeration .1.3.6.1.4.1.14179.2.2.22.1.4 |
bsnMeshNodeBackhaulRAPthe backhaul radio device for this APrw Enumeration .1.3.6.1.4.1.14179.2.2.22.1.5 |
bsnMeshNodeDataRatethis nodes backhaul data raterw Integer32 .1.3.6.1.4.1.14179.2.2.22.1.6 |
bsnMeshNodeChannelthis nodes backhaul channelro Integer32 .1.3.6.1.4.1.14179.2.2.22.1.7 |
bsnMeshNodeRoutingStaterouting statero Enumeration .1.3.6.1.4.1.14179.2.2.22.1.8 |
bsnMeshNodeMalformedNeighPacketsthe number of malformed neighbor packets.ro Counter32 .1.3.6.1.4.1.14179.2.2.22.1.9 |
bsnMeshNodePoorNeighSnrpoor neighbor snrro Counter32 .1.3.6.1.4.1.14179.2.2.22.1.10 |
bsnMeshNodeBlacklistPacketsthe number of blacklist packets receivedro Counter32 .1.3.6.1.4.1.14179.2.2.22.1.11 |
bsnMeshNodeInsufficientMemoryoccurences of insufficient memory conditionsro Counter32 .1.3.6.1.4.1.14179.2.2.22.1.12 |
bsnMeshNodeRxNeighReqRx neighbor requestsro Counter32 .1.3.6.1.4.1.14179.2.2.22.1.13 |
bsnMeshNodeRxNeighRspRx neighbor responsesro Counter32 .1.3.6.1.4.1.14179.2.2.22.1.14 |
bsnMeshNodeTxNeighReqTx neighbor requestsro Counter32 .1.3.6.1.4.1.14179.2.2.22.1.15 |
bsnMeshNodeTxNeighRspTx neighbor responsesro Counter32 .1.3.6.1.4.1.14179.2.2.22.1.16 |
bsnMeshNodeParentChangesnumber of parent changesro Counter32 .1.3.6.1.4.1.14179.2.2.22.1.17 |
bsnMeshNodeNeighTimeoutnumber of neighbor timeoutsro Counter32 .1.3.6.1.4.1.14179.2.2.22.1.18 |
bsnMeshNodeParentMacAddressparents mac addressedro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.2.22.1.19 |
bsnMeshNodeAPTypethe type of APro Enumeration .1.3.6.1.4.1.14179.2.2.22.1.20 |
bsnMeshNodeEthernetBridgeenable : Enables ethernet bridging on the AP. disable : Disables ethernet bridging on the AP. Changes are only applicable when AP is in 'Bridge' mode.rw Enumeration .1.3.6.1.4.1.14179.2.2.22.1.21 |
bsnMeshNodeHopsnumber of hops to rapro Integer32 .1.3.6.1.4.1.14179.2.2.22.1.30 |
bsnMeshNeighsTableThis is a table of mesh neighbors. SEQUENCE OF BsnMeshNeighsEntry .1.3.6.1.4.1.14179.2.2.23 |
bsnMeshNeighsEntryAn entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress and bsnMeshNeighNeighMacAddress BsnMeshNeighsEntry .1.3.6.1.4.1.14179.2.2.23.1 |
bsnMeshNeighMacAddressMAC Address of neighborro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.2.23.1.1 |
bsnMeshNeighTypeneighbor typero Enumeration .1.3.6.1.4.1.14179.2.2.23.1.2 |
bsnMeshNeighStateneighbor statero Enumeration .1.3.6.1.4.1.14179.2.2.23.1.3 |
bsnMeshNeighSnrexplicitly set SNRro Integer32 .1.3.6.1.4.1.14179.2.2.23.1.4 |
bsnMeshNeighSnrUpsnr upro Integer32 .1.3.6.1.4.1.14179.2.2.23.1.5 |
bsnMeshNeighSnrDownsnr downro Integer32 .1.3.6.1.4.1.14179.2.2.23.1.6 |
bsnMeshNeighLinkSnrlink snrro Integer32 .1.3.6.1.4.1.14179.2.2.23.1.7 |
bsnMeshNeighAdjustedEasehops adjusted easero Integer32 .1.3.6.1.4.1.14179.2.2.23.1.8 |
bsnMeshNeighUnadjustedEaseease to root AP from this APro Integer32 .1.3.6.1.4.1.14179.2.2.23.1.9 |
bsnMeshNeighRapEaseunadjusted ease received in last helloro Integer32 .1.3.6.1.4.1.14179.2.2.23.1.10 |
bsnMeshNeighTxParenttx packets to this node while a parentro Counter32 .1.3.6.1.4.1.14179.2.2.23.1.11 |
bsnMeshNeighRxParentrx packets from this node while a parentro Counter32 .1.3.6.1.4.1.14179.2.2.23.1.12 |
bsnMeshNeighPoorSnrpackets with poor snr received from this nodero Counter32 .1.3.6.1.4.1.14179.2.2.23.1.13 |
bsnMeshNeighLastUpdatelast received hello from this neighborro Integer32 .1.3.6.1.4.1.14179.2.2.23.1.14 |
bsnMeshNeighParentChangewhen this node last became parentro Integer32 .1.3.6.1.4.1.14179.2.2.23.1.20 |
bsnAPIfRadarChannelStatisticsTableThis is a table of channel information on which radar signal were detected. This will give the list of channels and last heard timestamp. Radar signals are detected only on 5Ghz range. So this will be detected for 802.11a interface. SEQUENCE OF BsnAPIfRadarChannelStatisticsEntry .1.3.6.1.4.1.14179.2.2.24 |
bsnAPIfRadarChannelStatisticsEntryAn entry (conceptual row) in the Table. Entries in this MIB are indexed by bsnAPDot3MacAddress, bsnAPIfSlotId, bsnAPIfRadarDetectedCannelNumber. BsnAPIfRadarChannelStatisticsEntry .1.3.6.1.4.1.14179.2.2.24.1 |
bsnAPIfRadarDetectedChannelNumberChannel Number on which radar signals were detected.ro Integer32 .1.3.6.1.4.1.14179.2.2.24.1.1 |
bsnAPIfRadarSignalLastHeardThis tells how many seconds ago radar signal was heard on the channel.ro Integer32 UNITS "seconds" .1.3.6.1.4.1.14179.2.2.24.1.2 |
bsnGlobalDot11 OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.3 |
bsnGlobalDot11Config OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.3.1 |
bsnGlobalDot11PrivacyOptionImplementedThis attribute, when true, shall indicate that the IEEE 802.11 WEP option is implemented. The default value of this attribute shall be false.ro Enumeration .1.3.6.1.4.1.14179.2.3.1.1 |
bsnGlobalDot11AuthenticationResponseTimeOutThis attribute shall specify the number of TU that a responding STA should wait for the next frame in the authentication sequence.rw Unsigned32 .1.3.6.1.4.1.14179.2.3.1.2 |
bsnGlobalDot11MultiDomainCapabilityImplementedThis attribute, when TRUE, indicates that the station implementation is capable of supporting multiple regulatory domains. The capability is disabled, otherwise. The default value of this attribute is FALSE.ro Enumeration .1.3.6.1.4.1.14179.2.3.1.3 |
bsnGlobalDot11MultiDomainCapabilityEnabledThis attribute, when TRUE, indicates that the capability of the station to operate in multiple regulatory domains is enabled. The capability is disabled, otherwise. The default value of this attribute is FALSE.ro Enumeration .1.3.6.1.4.1.14179.2.3.1.4 |
bsnGlobalDot11CountryIndexThis attribute identifies the country in which the station is operating.rwdeprecated Enumeration .1.3.6.1.4.1.14179.2.3.1.5 |
bsnGlobalDot11LoadBalancingThis attribute specifies if load balancing of clients is enabled on disabled. Global configuration of Load Balancing is now removed. Use cLWlanLoadBalancingEnable to configure it per WLAN.rwdeprecated Enumeration .1.3.6.1.4.1.14179.2.3.1.6 |
bsnGlobalDot11RogueTimerThis attribute specifies in seconds, the time interval after which a Rogue Entry in Rogue Table will expire if no beacon is heard from a Rogue.rw Integer32 .1.3.6.1.4.1.14179.2.3.1.7 |
bsnPrimaryMwarForAPsThis attribute specifies if this Switch acts a Master Switch for the Airespace APs. So if an Airespace AP doesn't find its Primary Switch, it will associate with this Switch.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.8 |
bsnRtpProtocolPriorityReal Time Protocol Priority.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.9 |
bsnSystemCurrentTimeThis attribute will display the Current System time on the Switch.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.3.1.10 |
bsnUpdateSystemTimeUse this attribute to change the System time on the Switch. Specify the new time in this Format MM/DD/YYYY HH:MM:SSrw DisplayString .1.3.6.1.4.1.14179.2.3.1.11 |
bsnOperatingTemperatureEnvironmentOperating Environment of the Airespace Switch. commercial is Commercial (0 to 40 C) and industrial is Industrial (-10 to 70 C)ro Enumeration .1.3.6.1.4.1.14179.2.3.1.12 |
bsnSensorTemperatureCurrent Internal Temperature of the unit in Centigradero Integer32 .1.3.6.1.4.1.14179.2.3.1.13 |
bsnTemperatureAlarmLowLimitInternal Temperature Alarm Low Limit in Centigrade. If the bsnSensorTemperature goes below this limit bsnSensedTemperatureTooLow Alarm will be sent outro Integer32 .1.3.6.1.4.1.14179.2.3.1.14 |
bsnTemperatureAlarmHighLimitInternal Temperature Alarm High Limit in Centigrade. If the bsnSensorTemperature goes above this limit bsnSensedTemperatureTooHigh Alarm will be sent outro Integer32 .1.3.6.1.4.1.14179.2.3.1.15 |
bsnVirtualGatewayAddressVirtual Gateway Address of the Switch. This is used by web auth and Ipsec. If the virtual IP Address is changed, the Switch has to be rebooted for the new Address to take effect. This is now replaced by the Virtual Interface in bsnswitching MIB.rw IpAddress .1.3.6.1.4.1.14179.2.3.1.16 |
bsnRFMobilityDomainNameRF Mobility Group Name to which this Airespace Switch belongs. Airespace Switches on a network form a RF Group as well as a Mobility Group. RF Groups does the channel and power management of AP while Mobility Group does load balancing and hand off for clients.rw OCTET STRING .1.3.6.1.4.1.14179.2.3.1.17 |
bsnClientWatchListFeatureThis flag should be turned on for the client watch lists to be enabled on the switch. When enabled, the switch generates Client Association and Authentication traps for the watchlisted clients.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.18 |
bsnRogueLocationDiscoveryProtocolThis flag should be turned on to enable the Rogue Location Discovery Protocol feature on the switch. We can either enable this feature for all the APs or only for APs in monitor mode.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.19 |
bsnRogueAutoContainFeatureThis flag should be turned on to allow the switch to contain the rogues automatically if detected on the wired network.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.20 |
bsnOverAirProvisionApModeOver the Air Provisioning Mode for APsrw Enumeration .1.3.6.1.4.1.14179.2.3.1.21 |
bsnMaximumNumberOfConcurrentLoginsThis attribute specifies the maximum number of concurrent logins that the switch will allow for a single user. A value 0 implies that there is no restriction on the number of concurrent logins with a single username.rw Integer32 .1.3.6.1.4.1.14179.2.3.1.22 |
bsnAutoContainRoguesAdvertisingSsidThis flag should be set to 1 to allow the switch to contain automatically those rogues that are advertising our SSID. If value is 0, only an alarm will be generated when such a rogue is detected.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.23 |
bsnAutoContainAdhocNetworksThis flag should be set to 1 to allow the switch to contain automatically the adhoc networks detected by the switch. If value is 0, only an alarm will be generated when such a network is detected.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.24 |
bsnAutoContainTrustedClientsOnRogueApsThis flag should be set to 1 to allow the switch to contain automatically those trusted clients that are associated to rogue APs. If value is 0, only an alarm will be generated when such a client is detected.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.25 |
bsnValidateRogueClientsAgainstAAAThis flag should be turned on to allow the switch to validate 'valid' mobiles associating with rogue APs. For example, if a client's MAC Address is found in the local MAC filter table, that client can be validated.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.26 |
bsnSystemTimezoneDeltaThe delta (difference) between the local time and the Universal Coordinated Time in hours. For example, it is -8 for the PST and +1 for France. If the delta is -5.30 then this attribute will store -5 and bsnSystemTimezoneDeltaMinutes will store 30. This value i should be between -23 to +23rw Integer32 .1.3.6.1.4.1.14179.2.3.1.27 |
bsnSystemTimezoneDaylightSavingsThis flag specifies if daylight savings are enabled for the current timezone.rwobsolete Enumeration .1.3.6.1.4.1.14179.2.3.1.28 |
bsnAllowAuthorizeApAgainstAAAThis flag specifies if LWAPP is allowed to get authorization via RADIUS or local database for an AP.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.29 |
bsnSystemTimezoneDeltaMinutesThe minutes component of delta (difference) between the local time and the Universal Coordinated Time.rw Integer32 .1.3.6.1.4.1.14179.2.3.1.30 |
bsnApFallbackEnabledThis flag specifies if the APs should continue LWAPP discoveries to fallback to the primary switch in case they are not already associated with it i.e they are associated with their respective secondary or tertiary switch instead.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.31 |
bsnAppleTalkEnabledThis flag turns on the appletalk bridging in the switch such that the packets from Apple clients that use appletalk format can be processed by the switch. When this flag is off, these packets are dropped.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.32 |
bsnTrustedApPolicyConfig OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.3.1.40 |
bsnPolicyForMisconfiguredApsThis flag should be turned on to allow the switch to contain misconfigured APs.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.40.1 |
bsnEncryptionPolicyEnforcedThe encryption policy that is enforced on the trusted APs.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.40.2 |
bsnPreamblePolicyEnforcedThe preamble policy that is enforced on the trusted APs.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.40.3 |
bsnDot11ModePolicyEnforcedThe 802.11 Mode policy that is enforced on the trusted APs.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.40.4 |
bsnRadioTypePolicyEnforcedThe radio type policy that is enforced on the trusted APs.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.40.5 |
bsnValidateSsidForTrustedApIf enabled, the SSID of trusted APs will be validated by the switch.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.40.6 |
bsnAlertIfTrustedApMissingIf enabled, an alert will be generated when a trusted AP is missing.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.40.7 |
bsnTrustedApEntryExpirationTimeoutThis attribute specifies in seconds, the time interval after which a Trusted AP Entry will expire if no beacon is heard from that AP.rw Integer32 .1.3.6.1.4.1.14179.2.3.1.40.8 |
bsnClientExclusionPolicyConfig OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.3.1.41 |
bsnExcessive80211AssocFailuresThis flag specifies if client should be excluded (blacklisted) if repeated 802.11 Association Failures occurs with a client.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.41.1 |
bsnExcessive80211AuthFailuresThis flag specifies if client should be excluded (blacklisted) if repeated 802.11 Authentication Failures occurs with a client.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.41.2 |
bsnExcessive8021xAuthFailuresThis flag specifies if client should be excluded (blacklisted) if repeated 802.1x Authentication Failures occurs with a client.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.41.3 |
bsnExternalPolicyServerFailuresThis flag specifies if client should be excluded (blacklisted) if repeated external policy server failures occurs with a client.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.41.4 |
bsnExcessiveWebAuthFailuresThis flag specifies if client should be excluded (blacklisted) if repeated Web Authentication Failures occurs with a client.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.41.5 |
bsnIPTheftORReuseThis flag specifies if client should be excluded (blacklisted) if it appears to be reusing an IP Address.(Possible IP Theft)rw Enumeration .1.3.6.1.4.1.14179.2.3.1.41.6 |
bsnSignatureConfig OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.3.1.42 |
bsnStandardSignatureTableThe table listing Standard Signatures configured on the switch. The standard signatures are provided with the released product. The standard signatures can be updated via file download to the switch. The table is indexed by the precedence of the signatures. SEQUENCE OF BsnStandardSignatureEntry .1.3.6.1.4.1.14179.2.3.1.42.1 |
bsnStandardSignatureEntry.... BsnStandardSignatureEntry .1.3.6.1.4.1.14179.2.3.1.42.1.1 |
bsnStandardSignaturePrecedencePrecedence of the signature. This specifies the order in which the signature is applied to a packet.ro Unsigned32 .1.3.6.1.4.1.14179.2.3.1.42.1.1.1 |
bsnStandardSignatureNameThis attribute is used to configure the name on a signature.ro DisplayString .1.3.6.1.4.1.14179.2.3.1.42.1.1.2 |
bsnStandardSignatureDescriptionThis attribute is used to configure the description of a signature.ro DisplayString .1.3.6.1.4.1.14179.2.3.1.42.1.1.3 |
bsnStandardSignatureFrameTypeThis attribute specifies the type of frame that needs to match a signature.ro Enumeration .1.3.6.1.4.1.14179.2.3.1.42.1.1.4 |
bsnStandardSignatureActionThis attribute specifies the action to be taken once a packet is found to match a signature.ro Enumeration .1.3.6.1.4.1.14179.2.3.1.42.1.1.5 |
bsnStandardSignatureStateThis attribute specifies the state of a signature. It is used to match packets only if the state is enabled.ro Enumeration .1.3.6.1.4.1.14179.2.3.1.42.1.1.6 |
bsnStandardSignatureFrequencyThis specifies the frequency of the matching packets after which the specified action is taken.rw Unsigned32 .1.3.6.1.4.1.14179.2.3.1.42.1.1.7 |
bsnStandardSignatureQuietTimeThis specifies the quiet time in seconds during which no matching packets are found after which the attack is considered stopped.rw Unsigned32 .1.3.6.1.4.1.14179.2.3.1.42.1.1.8 |
bsnStandardSignatureVersionThis specifies the signature version.ro Unsigned32 .1.3.6.1.4.1.14179.2.3.1.42.1.1.9 |
bsnStandardSignatureConfigTypeThis attribute specifies the type of Signature configuration. It's protocol when the protocol format is used in the UI to configure this. Pattern is the config type for all signatures in the released signature file and when signatures are configured using pattern format. Note: the signatures will be allowed to be i configured in later releases.ro Enumeration .1.3.6.1.4.1.14179.2.3.1.42.1.1.10 |
bsnStandardSignatureEnableThis object configures the status of a particular standard signature on LWAPP APs, for use in performing signature analysis on the received 802.11 data and/or management frames. A value of 'true' makes the Controller send the 'Signature Add LWAPP Message' to all the joined APs with the status field set to 'enable'. This makes the joined APs perform signature analysis on the received 802.11 data and/or management frames and report the discrepancies observed, if any, to the Controller. A value of 'false' makes the Controller send the 'Signature Add LWAPP Message' to all the joined APs with the status field set to 'disable'. The joined APs doesn't perform the signature analysis on the received 802.11 data and/or management frames for this particular signature, till the signature is enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.14179.2.3.1.42.1.1.11 |
bsnStandardSignatureMacInfoThis object defines the pattern followed by the LWAPP APs to perform signature analysis with this Standard signature and report the results to the Controller.ro BsnTxtSignatureMacInfo .1.3.6.1.4.1.14179.2.3.1.42.1.1.12 |
bsnStandardSignatureMacFreqThis object specifies the frequency of matching packets from a particular source after which the specified action is taken.rw Unsigned32 .1.3.6.1.4.1.14179.2.3.1.42.1.1.13 |
bsnStandardSignatureRowStatusRow Status for creation/deletion. Signature will allowed to be created, deleted and edited in later releases.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.3.1.42.1.1.20 |
bsnStandardSignatureIntervalInterval of the signature. This specifies the interval when the signature is applied to a packet.rw Unsigned32 .1.3.6.1.4.1.14179.2.3.1.42.1.1.21 |
bsnStandardSignaturePatternTableThe table listing the matching patterns specified for a i Standard Signature. These are instrumental in matching the signature with a packet. A maximum of 5 i patterns may be specifed for a signature. These are used for matching in the order of their index. SEQUENCE OF BsnStandardSignaturePatternEntry .1.3.6.1.4.1.14179.2.3.1.42.2 |
bsnStandardSignaturePatternEntry.... BsnStandardSignaturePatternEntry .1.3.6.1.4.1.14179.2.3.1.42.2.1 |
bsnStandardSignaturePatternIndexIndex of the pattern. This specifies the order in which the pattern is checked against the packet contents.ro Unsigned32 .1.3.6.1.4.1.14179.2.3.1.42.2.1.1 |
bsnStandardSignaturePatternOffsetOffset from the start of the packet where the AP looks for a match to the pattern.ro Unsigned32 .1.3.6.1.4.1.14179.2.3.1.42.2.1.2 |
bsnStandardSignaturePatternStringThis is the pattern string that the AP uses to match at the offset. Example: 0x616c7068615f3178ro DisplayString .1.3.6.1.4.1.14179.2.3.1.42.2.1.3 |
bsnStandardSignaturePatternMaskThis is the pattern mask. This is the bit mask that the AP uses to mask out the bits in the packet at the given offset. Example: 0xffffffffffffffffro DisplayString .1.3.6.1.4.1.14179.2.3.1.42.2.1.4 |
bsnStandardSignaturePatternOffSetStartThis object indicates how an offset should be applied while doing signature analysis for QOS and non-QOS data frames with this standard signature.ro BsnSignaturePatternOffSetStart .1.3.6.1.4.1.14179.2.3.1.42.2.1.5 |
bsnStandardSignaturePatternRowStatusRow Status for creation/deletion. Signature Pattern will allowed to be created, deleted and edited in later releases.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.3.1.42.2.1.15 |
bsnCustomSignatureTableThe table listing Standard Signatures configured on the switch. The standard signatures are provided with the released product. The standard signatures can be updated via file download to the switch. The table is indexed by the precedence of the signatures. SEQUENCE OF BsnCustomSignatureEntry .1.3.6.1.4.1.14179.2.3.1.42.3 |
bsnCustomSignatureEntry.... BsnCustomSignatureEntry .1.3.6.1.4.1.14179.2.3.1.42.3.1 |
bsnCustomSignaturePrecedencePrecedence of the signature. This specifies the order in which the signature is applied to a packet.ro Unsigned32 .1.3.6.1.4.1.14179.2.3.1.42.3.1.1 |
bsnCustomSignatureNameThis attribute is used to configure the name on a signature.ro DisplayString .1.3.6.1.4.1.14179.2.3.1.42.3.1.2 |
bsnCustomSignatureDescriptionThis attribute is used to configure the description of a signature.ro DisplayString .1.3.6.1.4.1.14179.2.3.1.42.3.1.3 |
bsnCustomSignatureFrameTypeThis attribute specifies the type of frame that needs to match a signature.ro Enumeration .1.3.6.1.4.1.14179.2.3.1.42.3.1.4 |
bsnCustomSignatureActionThis attribute specifies the action to be taken once a packet is found to match a signature.ro Enumeration .1.3.6.1.4.1.14179.2.3.1.42.3.1.5 |
bsnCustomSignatureStateThis attribute specifies the state of a signature. It is used to match packets only if the state is enabled.ro Enumeration .1.3.6.1.4.1.14179.2.3.1.42.3.1.6 |
bsnCustomSignatureFrequencyThis specifies the frequency of the matching packets after which the specified action is taken.rw Unsigned32 .1.3.6.1.4.1.14179.2.3.1.42.3.1.7 |
bsnCustomSignatureQuietTimeThis specifies the quiet time in seconds during which no matching packets are found after which the attack is considered stopped.rw Unsigned32 .1.3.6.1.4.1.14179.2.3.1.42.3.1.8 |
bsnCustomSignatureVersionThis specifies the signature version.ro Unsigned32 .1.3.6.1.4.1.14179.2.3.1.42.3.1.9 |
bsnCustomSignatureConfigTypeThis attribute specifies the type of Signature configuration. It's protocol when the protocol format is used in the UI to configure this. Pattern is the config type for all signatures in the released signature file and when signatures are configured using pattern format. Note: the signatures will be allowed to be configured in later releases.ro Enumeration .1.3.6.1.4.1.14179.2.3.1.42.3.1.10 |
bsnCustomSignatureEnableThis object configures the status of a particular Custom signature on LWAPP APs, for use in performing signature analysis on the received 802.11 data and/or management frames. A value of 'true' makes the Controller send the 'Signature Add LWAPP Message' to all the joined APs with the status field set to 'enable'. This makes the joined APs perform signature analysis on the received 802.11 data and/or management frames and report the discrepancies observed, if any, to the Controller. A value of 'false' makes the Controller send the 'Signature Add LWAPP Message' to all the joined APs with the status field set to 'disable'. The joined APs doesn't perform the signature analysis on the received 802.11 data and/or management frames for this particular signature, till the signature is enabled.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.14179.2.3.1.42.3.1.11 |
bsnCustomSignatureMacInfoThis object defines the pattern followed by the LWAPP APs to perform signature analysis with this Custom signature and report the results to the Controller.ro BsnTxtSignatureMacInfo .1.3.6.1.4.1.14179.2.3.1.42.3.1.12 |
bsnCustomSignatureMacFreqThis object specifies the frequency of matching packets from a particular source after which the specified action is taken.rw Unsigned32 .1.3.6.1.4.1.14179.2.3.1.42.3.1.13 |
bsnCustomSignatureRowStatusRow Status for creation/deletion. Signature will allowed to be created, deleted and edited in later releases.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.3.1.42.3.1.20 |
bsnCustomSignatureIntervalInterval of the signature. This specifies the interval when the signature is applied to a packet.rw Unsigned32 .1.3.6.1.4.1.14179.2.3.1.42.3.1.21 |
bsnCustomSignaturePatternTableThe table listing the matching patterns specified for a Standard Signature. These are instrumental in matching the signature with a packet. A maximum of 5 patterns may be specifed for a signature. These are used for matching in the order of their index. SEQUENCE OF BsnCustomSignaturePatternEntry .1.3.6.1.4.1.14179.2.3.1.42.4 |
bsnCustomSignaturePatternEntry.... BsnCustomSignaturePatternEntry .1.3.6.1.4.1.14179.2.3.1.42.4.1 |
bsnCustomSignaturePatternIndexIndex of the pattern. This specifies the order in which the pattern is checked against the packet contents.ro Unsigned32 .1.3.6.1.4.1.14179.2.3.1.42.4.1.1 |
bsnCustomSignaturePatternOffsetOffset from the start of the packet where the AP looks for a match to the pattern.ro Unsigned32 .1.3.6.1.4.1.14179.2.3.1.42.4.1.2 |
bsnCustomSignaturePatternStringThis is the pattern string that the AP uses to match at the offset. Example: 0x616c7068615f3178ro DisplayString .1.3.6.1.4.1.14179.2.3.1.42.4.1.3 |
bsnCustomSignaturePatternMaskThis is the pattern mask. This is the bit mask that the AP uses to mask out the bits in the packet at the given offset. Example: 0xffffffffffffffffro DisplayString .1.3.6.1.4.1.14179.2.3.1.42.4.1.4 |
bsnCustomSignaturePatternOffSetStartThis object indicates how an offset should be applied while doing signature analysis for QOS and non-QOS data frames with this custom signature.ro BsnSignaturePatternOffSetStart .1.3.6.1.4.1.14179.2.3.1.42.4.1.5 |
bsnCustomSignaturePatternRowStatusRow Status for creation/deletion. Signature Pattern will allowed to be created, deleted and edited in later releases.ro RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.3.1.42.4.1.15 |
bsnSignatureCheckStateThis flag should be enabled to enforce check of all standard and custom signatures. If disabled, there will be no check for signatures, both custom and standard, by the switch.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.42.5 |
bsnRfIdTagConfig OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.3.1.43 |
bsnRfIdTagStatusThis flag should be turned on to allow the switch to collect data for tags.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.43.1 |
bsnRfIdTagDataTimeoutThis is the number of seconds after which the tag data is deleted by the switch from its database if it didn't hear from the tag again.rw Unsigned32 .1.3.6.1.4.1.14179.2.3.1.43.2 |
bsnRfIdTagAutoTimeoutStatusThis flag should be turned on to allow auto deletion of tag data in the switch after expiration of Tag Data Timeoutrw Enumeration .1.3.6.1.4.1.14179.2.3.1.43.3 |
bsnAPNeighborAuthConfig OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.3.1.44 |
bsnAPNeighborAuthStatusThis flag should be turned on to allow the AP-Neighbor Authentication feature.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.44.1 |
bsnAPNeighborAuthAlarmThresholdAuthentication alarm trigger threshold.rw INTEGER .1.3.6.1.4.1.14179.2.3.1.44.2 |
bsnRFNetworkNameRF Network Group Name to which this Airespace Switch belongs. Airespace Switches on a network form a RF Network Group as well as a Mobility Group. RF Network Groups does the channel and power management of AP while Mobility Group does load balancing and hand off for clients.rw OCTET STRING .1.3.6.1.4.1.14179.2.3.1.45 |
bsnFastSSIDChangeFeatureConfigures Fast SSID changing feature for mobile-stations. When enabled, permits mobile-stations to change SSIDs without having to block and wait for SSID-cleanup on the switch to occur.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.46 |
bsnBridgingPolicyConfig OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.3.1.47 |
bsnBridgingZeroTouchConfigIf enabled, allows new bridging APs to negotiate with the switch to acquire the shared secret key.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.47.1 |
bsnBridgingSharedSecretKeyKey that is used to negotiate a secure LWAPP connection between a switch and a bridging or mesh AP.rw OCTET STRING .1.3.6.1.4.1.14179.2.3.1.47.2 |
bsnAcceptSelfSignedCertificateThis flag specifies if controller will accept Self Signed Certificate from AP as part of authorization.rw Enumeration .1.3.6.1.4.1.14179.2.3.1.48 |
bsnSystemClockTimeThis object represents the current clock time of the controller and expressed as the number of seconds elapsed since 00:00:00 on January 1, 1970, Coordinated Universal Time (UTC).ro Unsigned32 UNITS "seconds" .1.3.6.1.4.1.14179.2.3.1.49 |
bsnGlobalDot11b OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.3.2 |
bsnGlobalDot11bConfig OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.3.2.1 |
bsnGlobalDot11bNetworkStatus802.11b Network Admin Status.rw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.1 |
bsnGlobalDot11bBeaconPeriodThis attribute shall specify the number of TU that a AP Radio shall use for scheduling Beacon tranmissions. This value is transmitted in Beacon and Probe Response frames.rw INTEGER .1.3.6.1.4.1.14179.2.3.2.1.2 |
bsnGlobalDot11bDynamicChannelAssignmentDynamic channel assignment(DCA) has three modes. When the mode is auto, the channel assignment will be periodically updated for all Airespace APs that permit this operation. When the DCA is runOnce, channel assignments are updated based on the UPDATE_CMD received from the management. When the DCA is static, no dynamic channel assignments occurs and value are set to their global default. Default is auto.rw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.3 |
bsnGlobalDot11bCurrentChannelThe current operating frequency channel of the DSSS PHY. Valid channel numbers are as defined in 15.4.6.2. This attribute will be read-only if bsnAPIfPhyChannelAutomaticOn is true.rw INTEGER .1.3.6.1.4.1.14179.2.3.2.1.4 |
bsnGlobalDot11bDynamicChannelUpdateIntervalWhen Channel dynamic alogirthm is running, this interval (in secs) specifies how often Channel assignement updates are attempted on an Airespace AP. NOTE: hysteresis is built into the algorithms so we will not have uproductive changes occuring. Default value is 600 secsro Unsigned32 .1.3.6.1.4.1.14179.2.3.2.1.5 |
bsnGlobalDot11bInputsForDCAThis attribute is a bit mask specifying what to include in DCA optimization.Below is a list of parameters and their corresponding bits identifiers. options bit -------------------------------------- none 0 SIGNAL STRENGTH 1 NOISE 2 FOREIGN INTERFERENCE 4 LOAD 8 DEVICE INTERFERENCE 32 Default value is 63( all bits on).rw Unsigned32 .1.3.6.1.4.1.14179.2.3.2.1.6 |
bsnGlobalDot11bChannelUpdateCmdInvokeWhen set to activate this starts a DCA calculation regardless of the dynamic update interval. This command should be invoke on Group Leader Airespace Switch.Invoking on a Airespace Switch which is not a Group leader has no effect.rw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.7 |
bsnGlobalDot11bChannelUpdateCmdStatusAfter setting bsnGlobalDot11bChannelUpdateCmdInvoke to activate, the result of action can be monitored from here. It takes 5 minutes for the command to complete.ro Integer32 .1.3.6.1.4.1.14179.2.3.2.1.8 |
bsnGlobalDot11bDynamicTransmitPowerControlDynamic transmit power (DTP) has three modes. When the mode is auto, the transmit power of each Airespace AP will be periodically updated for all Airespace APs that permit this operation. When the DTP is runOnce,transmit power update will occur based on the UPDATE_CMD received from the management. When the DTP is static, no dynamic transmit power updates occur and their global defaults are used. Default is auto.rw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.9 |
bsnGlobalDot11bDynamicTxPowerControlIntervalWhen Tx PowerControl dynamic alogirthm is running, this interval(in secs) specifies how often TxPower control updates are attempted on an Airespace AP. NOTE: hysteresis is build into the algorithms so we will not have uproductive changes occuring. Default value is 600 secsro Unsigned32 .1.3.6.1.4.1.14179.2.3.2.1.10 |
bsnGlobalDot11bCurrentTxPowerLevelThe TxPowerLevel N currently being used to transmit data. Some PHYs also use this value to determine the receiver sensitivity requirements for CCA.rw INTEGER .1.3.6.1.4.1.14179.2.3.2.1.11 |
bsnGlobalDot11bInputsForDTPThis attribute is a bit mask specifying what to include in DCA optimization.Below is a list of parameters and their corresponding bits identifiers. options bit -------------------------------------- none 0 LOAD 1 SIGNAL STRENGTH 2 FOREIGN INTERFERENCE 4 NOISE 8 Default value is 15( all bits on).rw Unsigned32 .1.3.6.1.4.1.14179.2.3.2.1.12 |
bsnGlobalDot11bPowerUpdateCmdInvokeWhen set to activate this starts a DTP calculation regardless of the dynamic update interval. This command should be invoke on Group Leader Airespace Switch.Invoking on a Airespace Switch which is not a Group leader has no effect.rw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.13 |
bsnGlobalDot11bPowerUpdateCmdStatusAfter setting bsnGlobalDot11aChannelUpdateCmdInvoke to activate, the result of action can be monitored from here. It takes 5 minutes for the command to complete.ro Integer32 .1.3.6.1.4.1.14179.2.3.2.1.14 |
bsnGlobalDot11bDataRate1MhzSpecify if this rate is supported or mandatory or disabledrw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.15 |
bsnGlobalDot11bDataRate2MhzSpecify if this rate is supported or mandatory or disabledrw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.16 |
bsnGlobalDot11bDataRate5AndHalfMhzSpecify if this rate is supported or mandatory or disabledrw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.17 |
bsnGlobalDot11bDataRate11MhzSpecify if this rate is supported or mandatory or disabledrw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.18 |
bsnGlobalDot11bShortPreamble802.11b Short Preamble.rw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.19 |
bsnGlobalDot11bDot11gSupportThis attribute is enabled to also support 802.11g protocol on the 802.11b network. Enabling 802.11g allows additional data rates: 6, 9, 12, 18, 24, 36, 48, 54 Mbps.rw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.20 |
bsnGlobalDot11bDataRate6MhzSpecify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.rw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.21 |
bsnGlobalDot11bDataRate9MhzSpecify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.rw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.22 |
bsnGlobalDot11bDataRate12MhzSpecify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.rw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.23 |
bsnGlobalDot11bDataRate18MhzSpecify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.rw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.24 |
bsnGlobalDot11bDataRate24MhzSpecify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.rw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.25 |
bsnGlobalDot11bDataRate36MhzSpecify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.rw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.26 |
bsnGlobalDot11bDataRate48MhzSpecify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.rw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.27 |
bsnGlobalDot11bDataRate54MhzSpecify if this rate is supported or mandatory or disabled. This is configurable only if 802.11g support is enabled.rw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.28 |
bsnGlobalDot11bPicoCellModeConfigures the 802.11b pico-cell mode. This cannot be enabled when the Fast Roaming Mode is enabled.rw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.29 |
bsnGlobalDot11bFastRoamingModeConfigures the 802.11b fast-roaming mode. This cannot be enabled when the Pico Cell Mode is enabled.rw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.30 |
bsnGlobalDot11bFastRoamingVoipMinRateConfigures the minimum transmission rate allowed for VoIP on any 802.11b radio.rw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.31 |
bsnGlobalDot11bFastRoamingVoipPercentageConfigures the percentage of effective bandwidth for the minimum rate reserved for VoIP.rw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.32 |
bsnGlobalDot11b80211eMaxBandwidthThis represents the maximum bandwidth allocated to 802.11e clients. It is expressed as percentage of the total bandwidth of 802.11b network. The value of this attribute can vary from 0 to 100.rw INTEGER .1.3.6.1.4.1.14179.2.3.2.1.33 |
bsnGlobalDot11bDTPCSupportThis attribute may be used to enable the DTPC support on all 802.11b/g radios. DTPC or Dynamic Transmit Power Control support means that the radio's transmit power will be advertised in the beacons and probe responses.rw Enumeration .1.3.6.1.4.1.14179.2.3.2.1.34 |
bsnGlobalDot11bPhy OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.3.2.2 |
bsnGlobalDot11bMediumOccupancyLimitThis attribute shall indicate the maximum amount of time, in TU, that a point coordinator may control the usage of the wireless medium without relinquishing control for long enough to allow at least one instance of DCF access to the medium. The default value of this attribute shall be 100, and the maximum value shall be 1000.ro INTEGER .1.3.6.1.4.1.14179.2.3.2.2.1 |
bsnGlobalDot11bCFPPeriodThe attribute shall describe the number of DTIM intervals between the start of CFPs. It is modified by MLME-START.request primitive.ro INTEGER .1.3.6.1.4.1.14179.2.3.2.2.2 |
bsnGlobalDot11bCFPMaxDurationThe attribute shall describe the maximum duration of the CFP in TU that may be generated by the PCF. It is modified by MLME-START.request primitive.ro INTEGER .1.3.6.1.4.1.14179.2.3.2.2.3 |
bsnGlobalDot11bCFPollableWhen this attribute is true, it shall indicate that the STA is able to respond to a CF-Poll with a data frame within a SIFS time. This attribute shall be false if the STA is not able to respond to a CF-Poll with a data frame within a SIFS time.ro Enumeration .1.3.6.1.4.1.14179.2.3.2.2.5 |
bsnGlobalDot11bCFPollRequestSpecifies wheather CFPro Enumeration .1.3.6.1.4.1.14179.2.3.2.2.6 |
bsnGlobalDot11bDTIMPeriodThis attribute shall specify the number of beacon intervals that shall elapse between transmission of Beacons frames containing a TIM element whose DTIM Count field is 0. This value is transmitted in the DTIM Period field of Beacon frames.rw INTEGER .1.3.6.1.4.1.14179.2.3.2.2.7 |
bsnGlobalDot11bMaximumTransmitPowerLevelThis attribute shall indicate the maximum transmit power, in dBm, allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.rodeprecated Integer32 .1.3.6.1.4.1.14179.2.3.2.2.8 |
bsnGlobalDot11bFirstChannelNumberThis attribute shall indicate the value of the lowest channel number in the subband for the associated domain country string. The default value of this attribute shall be zero.rodeprecated Integer32 .1.3.6.1.4.1.14179.2.3.2.2.9 |
bsnGlobalDot11bNumberofChannelsThis attribute shall indicate the value of the total number of channels allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.rodeprecated Integer32 .1.3.6.1.4.1.14179.2.3.2.2.10 |
bsnGlobalDot11bRTSThresholdThis attribute shall indicate the number of octets in an MPDU, below which an RTS/CTS handshake shall not be performed. An RTS/CTS handshake shall be performed at the beginning of any frame exchange sequence where the MPDU is of type Data or Management, the MPDU has an individual address in the Address1 field, and the length of the MPDU is greater than this threshold. (For additional details, refer to Table 21 in 9.7.) Setting this attribute to be larger than the maximum MSDU size shall have the effect of turning off the RTS/CTS handshake for frames of Data or Management type transmitted by this STA. Setting this attribute to zero shall have the effect of turning on the RTS/CTS handshake for all frames of Data or Management type transmitted by this STA. The default value of this attribute shall be 2347.ro INTEGER .1.3.6.1.4.1.14179.2.3.2.2.11 |
bsnGlobalDot11bShortRetryLimitThis attribute shall indicate the maximum number of transmission attempts of a frame, the length of which is less than or equal to bsnGlobalDot11RTSThreshold, that shall be made before a failure condition is indicated. The default value of this attribute shall be 7.ro INTEGER .1.3.6.1.4.1.14179.2.3.2.2.12 |
bsnGlobalDot11bLongRetryLimitThis attribute shall indicate the maximum number of transmission attempts of a frame, the length of which is greater than bsnGlobalDot11RTSThreshold, that shall be made before a failure condition is indicated. The default value of this attribute shall be 4.ro INTEGER .1.3.6.1.4.1.14179.2.3.2.2.13 |
bsnGlobalDot11bFragmentationThresholdThis attribute shall specify the current maximum size, in octets, of the MPDU that may be delivered to the PHY. An MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers. An MSDU or MMPDU shall be fragmented when the resulting frame has individual address in the Address1 field, and the length of the frame is larger than this threshold. The default value for this attribute shall be the lesser of 2346 or the aMPDUMaxLength of the attached PHY and shall never exceed the lesser of 2346 or the aMPDUMaxLength of the attached PHY. The value of this attribute shall never be less than 256.rw INTEGER .1.3.6.1.4.1.14179.2.3.2.2.14 |
bsnGlobalDot11bMaxTransmitMSDULifetimeThe MaxTransmitMSDULifetime shall be the elapsed time in TU, after the initial transmission of an MSDU, after which further attempts to transmit the MSDU shall be terminated. The default value of this attribute shall be 512.ro Unsigned32 .1.3.6.1.4.1.14179.2.3.2.2.15 |
bsnGlobalDot11bMaxReceiveLifetimeThe MaxReceiveLifetime shall be the elapsed time in TU, after the initial reception of a fragmented MMPDU or MSDU, after which further attempts to reassemble the MMPDU or MSDU shall be terminated. The default value shall be 512.ro Unsigned32 .1.3.6.1.4.1.14179.2.3.2.2.16 |
bsnGlobalDot11bEDThresholdThe current Energy Detect Threshold being used by the DSSS PHY.ro Integer32 .1.3.6.1.4.1.14179.2.3.2.2.17 |
bsnGlobalDot11bChannelAgilityEnabledThis attribute indicates that the PHY channel agility functionality is enabled.ro Enumeration .1.3.6.1.4.1.14179.2.3.2.2.18 |
bsnGlobalDot11bPBCCOptionImplementedThis attribute, when true, shall indicate that the PBCC modulation option as defined in subclause 18.4.6.6 is implemented. The default value of this attribute shall be false.ro Enumeration .1.3.6.1.4.1.14179.2.3.2.2.19 |
bsnGlobalDot11bShortPreambleOptionImplementedThis attribute, when true, shall indicate that the short preamble option as defined in subclause 18.2.2.2 is implemented. The default value of this attribute shall be false.ro Enumeration .1.3.6.1.4.1.14179.2.3.2.2.20 |
bsnGlobalDot11a OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.3.3 |
bsnGlobalDot11aConfig OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.3.3.1 |
bsnGlobalDot11aNetworkStatusDot11a Network Statusrw Enumeration .1.3.6.1.4.1.14179.2.3.3.1.1 |
bsnGlobalDot11aLowBandNetworkDot11a Low Band Network Statusro Enumeration .1.3.6.1.4.1.14179.2.3.3.1.2 |
bsnGlobalDot11aMediumBandNetworkDot11a Mid Band Network Statusro Enumeration .1.3.6.1.4.1.14179.2.3.3.1.3 |
bsnGlobalDot11aHighBandNetworkDot11a High Band Network Statusro Enumeration .1.3.6.1.4.1.14179.2.3.3.1.4 |
bsnGlobalDot11aBeaconPeriodThis attribute shall specify the number of TU that a AP Radio shall use for scheduling Beacon tranmissions. This value is transmitted in Beacon and Probe Response frames.rw INTEGER .1.3.6.1.4.1.14179.2.3.3.1.5 |
bsnGlobalDot11aDynamicChannelAssignmentDynamic channel assignment(DCA) has three modes. When the mode is auto, the channel assignment will be periodically updated for all Airespace APs that permit this operation. When the DCA is runOnce, channel assignments are updated based on the UPDATE_CMD received from the management. When the DCA is static, no dynamic channel assignments occurs and value are set to their global default. Default is auto.rw Enumeration .1.3.6.1.4.1.14179.2.3.3.1.6 |
bsnGlobalDot11aCurrentChannelThe number of the current operating frequency channel of the OFDM PHY.rw INTEGER .1.3.6.1.4.1.14179.2.3.3.1.7 |
bsnGlobalDot11aDynamicChannelUpdateIntervalWhen Channel dynamic alogirthm is running, this interval(in secs) specifies how often Channel assignement updates are attempted on an Airespace AP. NOTE: hysteresis is build into the algorithms so we will not have uproductive changes occuring. Default value is 600 secsro Unsigned32 .1.3.6.1.4.1.14179.2.3.3.1.8 |
bsnGlobalDot11aInputsForDCAThis attribute is a bit mask specifying what to include in DCA optimization.Below is a list of parameters and their corresponding bits identifiers. options bit -------------------------------------- none 0 SIGNAL STRENGTH 1 NOISE 2 FOREIGN INTERFERENCE 4 LOAD 8 DEVICE INTERFERENCE 32 Default value is 63( all bits on).rw Unsigned32 .1.3.6.1.4.1.14179.2.3.3.1.9 |
bsnGlobalDot11aChannelUpdateCmdInvokeWhen set to activate this starts a DCA calculation regardless of the dynamic update interval. This command should be invoke on Group Leader Airespace Switch.Invoking on a Airespace Switch which is not a Group leader has no effect.rw Enumeration .1.3.6.1.4.1.14179.2.3.3.1.10 |
bsnGlobalDot11aChannelUpdateCmdStatusAfter setting bsnGlobalDot11aChannelUpdateCmdInvoke to activate, the result of action can be monitored from here. It takes 5 minutes for the command to complete.ro Integer32 .1.3.6.1.4.1.14179.2.3.3.1.11 |
bsnGlobalDot11aDynamicTransmitPowerControlDynamic transmit power (DTP) has three modes. When the mode is auto, the transmit power of each Airespace AP will be periodically updated for all Airespace APs that permit this operation. When the DTP is runOnce,transmit power update will occur based on the UPDATE_CMD received from the management. When the DTP is static, no dynamic transmit power updates occur and their global defaults are used. Default is auto.rw Enumeration .1.3.6.1.4.1.14179.2.3.3.1.12 |
bsnGlobalDot11aCurrentTxPowerLevelThe TxPowerLevel N currently being used to transmit data. Some PHYs also use this value to determine the receiver sensitivity requirements for CCA.rw INTEGER .1.3.6.1.4.1.14179.2.3.3.1.13 |
bsnGlobalDot11aDynamicTxPowerControlIntervalWhen Tx PowerControl dynamic alogirthm is running, this interval(in secs) specifies how often TxPower control updates are attempted on an Airespace AP. NOTE: hysteresis is build into the algorithms so we will not have uproductive changes occuring. Default value is 600 secsro Unsigned32 .1.3.6.1.4.1.14179.2.3.3.1.14 |
bsnGlobalDot11aInputsForDTPThis attribute is a bit mask specifying what to include in DCA optimization.Below is a list of parameters and their corresponding bits identifiers. options bit -------------------------------------- none 0 LOAD 1 SIGNAL STRENGTH 2 FOREIGN INTERFERENCE 4 NOISE 8 Default value is 15( all bits on).rw Unsigned32 .1.3.6.1.4.1.14179.2.3.3.1.15 |
bsnGlobalDot11aPowerUpdateCmdInvokeWhen set to activate this starts a DTP calculation regardless of the dynamic update interval. This command should be invoke on Group Leader Airespace Switch.Invoking on a Airespace Switch which is not a Group leader has no effect.rw Enumeration .1.3.6.1.4.1.14179.2.3.3.1.16 |
bsnGlobalDot11aPowerUpdateCmdStatusAfter setting bsnGlobalDot11aChannelUpdateCmdInvoke to activate, the result of action can be monitored from here. It takes 5 minutes for the command to complete.ro Integer32 .1.3.6.1.4.1.14179.2.3.3.1.17 |
bsnGlobalDot11aDataRate6MhzSpecify if this rate is supported or mandatory or disabledrw Enumeration .1.3.6.1.4.1.14179.2.3.3.1.19 |
bsnGlobalDot11aDataRate9MhzSpecify if this rate is supported or mandatory or disabledrw Enumeration .1.3.6.1.4.1.14179.2.3.3.1.20 |
bsnGlobalDot11aDataRate12MhzSpecify if this rate is supported or mandatory or disabledrw Enumeration .1.3.6.1.4.1.14179.2.3.3.1.21 |
bsnGlobalDot11aDataRate18MhzSpecify if this rate is supported or mandatory or disabledrw Enumeration .1.3.6.1.4.1.14179.2.3.3.1.22 |
bsnGlobalDot11aDataRate24MhzSpecify if this rate is supported or mandatory or disabledrw Enumeration .1.3.6.1.4.1.14179.2.3.3.1.23 |
bsnGlobalDot11aDataRate36MhzSpecify if this rate is supported or mandatory or disabledrw Enumeration .1.3.6.1.4.1.14179.2.3.3.1.24 |
bsnGlobalDot11aDataRate48MhzSpecify if this rate is supported or mandatory or disabledrw Enumeration .1.3.6.1.4.1.14179.2.3.3.1.25 |
bsnGlobalDot11aDataRate54MhzSpecify if this rate is supported or mandatory or disabledrw Enumeration .1.3.6.1.4.1.14179.2.3.3.1.26 |
bsnGlobalDot11aPicoCellModeConfigures the 802.11a pico-cell mode. This cannot be enabled when the Fast Roaming Mode is enabled.rw Enumeration .1.3.6.1.4.1.14179.2.3.3.1.27 |
bsnGlobalDot11aFastRoamingModeConfigures the 802.11a fast-roaming mode. This cannot be enabled when the Pico Cell Mode is enabled.rw Enumeration .1.3.6.1.4.1.14179.2.3.3.1.28 |
bsnGlobalDot11aFastRoamingVoipMinRateConfigures the minimum transmission rate allowed for VoIP on any 802.11a radio.rw Enumeration .1.3.6.1.4.1.14179.2.3.3.1.29 |
bsnGlobalDot11aFastRoamingVoipPercentageConfigures the percentage of effective bandwidth for the minimum rate reserved for VoIP.rw Enumeration .1.3.6.1.4.1.14179.2.3.3.1.30 |
bsnGlobalDot11a80211eMaxBandwidthThis represents the maximum bandwidth allocated to 802.11e clients. It is expressed as percentage of the total bandwidth of 802.11a network. The value of this attribute can vary from 0 to 100.rw INTEGER .1.3.6.1.4.1.14179.2.3.3.1.31 |
bsnGlobalDot11aDTPCSupportThis attribute may be used to enable the DTPC support on all 802.11a radios. DTPC or Dynamic Transmit Power Control support means that the radio's transmit power will be advertised in the beacons and probe responses.rw Enumeration .1.3.6.1.4.1.14179.2.3.3.1.32 |
bsnGlobalDot11aPhy OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.3.3.2 |
bsnGlobalDot11aMediumOccupancyLimitThis attribute shall indicate the maximum amount of time, in TU, that a point coordinator may control the usage of the wireless medium without relinquishing control for long enough to allow at least one instance of DCF access to the medium. The default value of this attribute shall be 100, and the maximum value shall be 1000.ro INTEGER .1.3.6.1.4.1.14179.2.3.3.2.1 |
bsnGlobalDot11aCFPPeriodThe attribute shall describe the number of DTIM intervals between the start of CFPs. It is modified by MLME-START.request primitive.ro INTEGER .1.3.6.1.4.1.14179.2.3.3.2.2 |
bsnGlobalDot11aCFPMaxDurationThe attribute shall describe the maximum duration of the CFP in TU that may be generated by the PCF. It is modified by MLME-START.request primitive.ro INTEGER .1.3.6.1.4.1.14179.2.3.3.2.3 |
bsnGlobalDot11aCFPollableWhen this attribute is true, it shall indicate that the STA is able to respond to a CF-Poll with a data frame within a SIFS time. This attribute shall be false if the STA is not able to respond to a CF-Poll with a data frame within a SIFS time.ro Enumeration .1.3.6.1.4.1.14179.2.3.3.2.5 |
bsnGlobalDot11aCFPollRequestSpecifies whether CFPro Enumeration .1.3.6.1.4.1.14179.2.3.3.2.6 |
bsnGlobalDot11aDTIMPeriodThis attribute shall specify the number of beacon intervals that shall elapse between transmission of Beacons frames containing a TIM element whose DTIM Count field is 0. This value is transmitted in the DTIM Period field of Beacon frames.rw INTEGER .1.3.6.1.4.1.14179.2.3.3.2.7 |
bsnGlobalDot11aMaximumTransmitPowerLevelThis attribute shall indicate the maximum transmit power, in dBm, allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.rodeprecated Integer32 .1.3.6.1.4.1.14179.2.3.3.2.8 |
bsnGlobalDot11aFirstChannelNumberThis attribute shall indicate the value of the lowest channel number in the subband for the associated domain country string. The default value of this attribute shall be zero.rodeprecated Integer32 .1.3.6.1.4.1.14179.2.3.3.2.9 |
bsnGlobalDot11aNumberofChannelsThis attribute shall indicate the value of the total number of channels allowed in the subband for the associated domain country string. The default value of this attribute shall be zero.rodeprecated Integer32 .1.3.6.1.4.1.14179.2.3.3.2.10 |
bsnGlobalDot11aRTSThresholdThis attribute shall indicate the number of octets in an MPDU, below which an RTS/CTS handshake shall not be performed. An RTS/CTS handshake shall be performed at the beginning of any frame exchange sequence where the MPDU is of type Data or Management, the MPDU has an individual address in the Address1 field, and the length of the MPDU is greater than this threshold. (For additional details, refer to Table 21 in 9.7.) Setting this attribute to be larger than the maximum MSDU size shall have the effect of turning off the RTS/CTS handshake for frames of Data or Management type transmitted by this STA. Setting this attribute to zero shall have the effect of turning on the RTS/CTS handshake for all frames of Data or Management type transmitted by this STA. The default value of this attribute shall be 2347.ro INTEGER .1.3.6.1.4.1.14179.2.3.3.2.11 |
bsnGlobalDot11aShortRetryLimitThis attribute shall indicate the maximum number of transmission attempts of a frame, the length of which is less than or equal to bsnGlobalDot11RTSThreshold, that shall be made before a failure condition is indicated. The default value of this attribute shall be 7.ro INTEGER .1.3.6.1.4.1.14179.2.3.3.2.12 |
bsnGlobalDot11aLongRetryLimitThis attribute shall indicate the maximum number of transmission attempts of a frame, the length of which is greater than bsnGlobalDot11RTSThreshold, that shall be made before a failure condition is indicated. The default value of this attribute shall be 4.ro INTEGER .1.3.6.1.4.1.14179.2.3.3.2.13 |
bsnGlobalDot11aFragmentationThresholdThis attribute shall specify the current maximum size, in octets, of the MPDU that may be delivered to the PHY. An MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers. MSDU or MMPDU shall be fragmented when the resulting frame has an individual address in the Address1 field, and the length of the frame is larger than this threshold. The default value for this attribute shall be the lesser of 2346 or the aMPDUMaxLength of the attached PHY and shall never exceed the lesser of 2346 or the aMPDUMaxLength of the attached PHY. The value of this attribute shall never be less than 256.rw INTEGER .1.3.6.1.4.1.14179.2.3.3.2.14 |
bsnGlobalDot11aMaxTransmitMSDULifetimeThe MaxTransmitMSDULifetime shall be the elapsed time in TU, after the initial transmission of an MSDU, after which further attempts to transmit the MSDU shall be terminated. The default value of this attribute shall be 512.ro Unsigned32 .1.3.6.1.4.1.14179.2.3.3.2.15 |
bsnGlobalDot11aMaxReceiveLifetimeThe MaxReceiveLifetime shall be the elapsed time in TU, after the initial reception of a fragmented MMPDU or MSDU, after which further attempts to reassemble the MMPDU or MSDU shall be terminated. The default value shall be 512.ro Unsigned32 .1.3.6.1.4.1.14179.2.3.3.2.16 |
bsnGlobalDot11aTIThresholdThe Threshold being used to detect a busy medium (frequency). CCA shall report a busy medium upon detecting the RSSI above this threshold.ro Integer32 .1.3.6.1.4.1.14179.2.3.3.2.17 |
bsnGlobalDot11aChannelAgilityEnabledThis attribute indicates that the PHY channel agility functionality is enabled.ro Enumeration .1.3.6.1.4.1.14179.2.3.3.2.18 |
bsnGlobalDot11h OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.3.4 |
bsnGlobalDot11hConfig OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.3.4.1 |
bsnGlobalDot11hPowerConstraintLocal maximum transmit power for a channel is defined as maximum transmit power level specified for the channel in the Country element minus the local power constraint specified for the channel in the Power Constraint element.The power constraint is coded as an unsigned integer in units of decibels. To disable power constraint set Power Constraint to 0.rw INTEGER .1.3.6.1.4.1.14179.2.3.4.1.1 |
bsnGlobalDot11hChannelSwitchEnableTo enable or disable channel switch. When disabling Channel Switch no need to pass mode and countrw Enumeration .1.3.6.1.4.1.14179.2.3.4.1.2 |
bsnGlobalDot11hChannelSwitchModeThe Channel Switch Mode indicates any restriction on transmission until a channel switch. An Channel mode set to 1 means that the STA in a BSS to which the frame containing the element is addressed shall tranmit no further frames with in the BSS until the scheduled channel switch. A Channel switch mode set to 0 does not impose any requirement on the receiving STA.rw Enumeration .1.3.6.1.4.1.14179.2.3.4.1.3 |
bsnRrm OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.4 |
bsnRrmDot11a OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.4.1 |
bsnRrmDot11aGroup OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.4.1.1 |
bsnRrmDot11aGlobalAutomaticGroupingDynamic grouping has two modes: on and off. When the grouping is off, no dynamic grouping occurs. Each Airespace Switch optimizes only its own Airespace APs' parameters. When grouping is on, the Airespace Switches form groups and elect leaders to perform better dynamic parameter optimization.rw Enumeration .1.3.6.1.4.1.14179.2.4.1.1.1 |
bsnRrmDot11aGroupLeaderMacAddrThis is the MAC address of the group leader for the dot11a group containing this Airespace Switch.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.4.1.1.2 |
bsnRrmIsDot11aGroupLeaderIf this Airespace Switch is a Dot11a Group Leader then this attribute will be true else it will be false.ro Enumeration .1.3.6.1.4.1.14179.2.4.1.1.3 |
bsnRrmDot11aGroupLastUpdateTimeLast time the dot11a grouping was updated on this Airespace Switch. This is valid only if the Airespace Switch is a group leader.ro Unsigned32 .1.3.6.1.4.1.14179.2.4.1.1.4 |
bsnRrmDot11aGlobalGroupIntervalWhen grouping is on, this interval(in secs) represents the period with which the grouping algorithm is run. Grouping algorithm will also run when the group contents changes and the automatic grouping is enabled. A dynamic grouping can be started upon request from the system administrator. Default value is 3600 secs.ro Unsigned32 .1.3.6.1.4.1.14179.2.4.1.1.5 |
bsnWrasDot11aGroupTableThis is a table of Airespace Switch addresses that identifies the members of the Dot11a RF group containing this Airespace Switch. Max size is 20 entries. SEQUENCE OF BsnWrasDot11aGroupEntry .1.3.6.1.4.1.14179.2.4.1.1.9 |
bsnWrasDot11aGroupEntry... BsnWrasDot11aGroupEntry .1.3.6.1.4.1.14179.2.4.1.1.9.1 |
bsnWrasDot11aPeerMacAddressThe MAC address of the member Switch.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.4.1.1.9.1.1 |
bsnWrasDot11aPeerIpAddressThe IP address of the Airespace Switch.ro IpAddress .1.3.6.1.4.1.14179.2.4.1.1.9.1.21 |
bsnRrmDot11aAPDefault OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.4.1.6 |
bsnRrmDot11aForeignInterferenceThresholdforeign 802.11A interference threshold between 0 and 100 percent.rw INTEGER .1.3.6.1.4.1.14179.2.4.1.6.1 |
bsnRrmDot11aForeignNoiseThreshold802.11A foreign noise threshold between -127 and 0 dBm.rw INTEGER (-127..0) .1.3.6.1.4.1.14179.2.4.1.6.2 |
bsnRrmDot11aRFUtilizationThreshold802.11A RF utlization threshold between 0 and 100 percent.rw INTEGER .1.3.6.1.4.1.14179.2.4.1.6.3 |
bsnRrmDot11aThroughputThreshold802.11A throughput threshold between 1000 and 100000rw Unsigned32 .1.3.6.1.4.1.14179.2.4.1.6.4 |
bsnRrmDot11aMobilesThreshold802.11A mobiles threshold between 1 and 75rw INTEGER .1.3.6.1.4.1.14179.2.4.1.6.5 |
bsnRrmDot11aCoverageThreshold802.11A coverage threshold between 3 and 50.rw INTEGER .1.3.6.1.4.1.14179.2.4.1.6.6 |
bsnRrmDot11aMobileMinExceptionLevel802.11A mobile minimum exception level between 1 and 75rw INTEGER .1.3.6.1.4.1.14179.2.4.1.6.7 |
bsnRrmDot11aCoverageExceptionLevel802.11A coverage exception level between 0 and 100 percent.rw INTEGER .1.3.6.1.4.1.14179.2.4.1.6.8 |
bsnRrmDot11aSignalMeasurementIntervalThis interval (in secs) specifies how often do we get new signal strength measurements at each Airespace AP. Default is 300 secsrw Unsigned32 .1.3.6.1.4.1.14179.2.4.1.6.9 |
bsnRrmDot11aNoiseMeasurementIntervalThis interval( in secs) specifies how often do we get new noise and interference measurements at each Airespace AP. Default is 300 secsrw Unsigned32 .1.3.6.1.4.1.14179.2.4.1.6.10 |
bsnRrmDot11aLoadMeasurementIntervalThis interval( in secs) specifies how often do we get new load measurements at each Airespace AP. Default is 300 secsrw Unsigned32 .1.3.6.1.4.1.14179.2.4.1.6.11 |
bsnRrmDot11aCoverageMeasurementIntervalThis interval( in secs) specifies how often do we get new coverage measurements at each Airespace AP. Default is 300 secsrw Unsigned32 .1.3.6.1.4.1.14179.2.4.1.6.12 |
bsnRrmDot11aChannelMonitorListThis attribute specifies the channels on which the switch monitors noise, interference and rogues. The first option allows monitoring on all channels while the second one on only those that are supported by the country of operation. the option dca implies that the monitor channel list will include those channels that are used by automatic channel assignment.rw Enumeration .1.3.6.1.4.1.14179.2.4.1.6.13 |
bsnRrmDot11aSetFactoryDefaultWhen set to activate all rrm parameters are reset to factory defaultsrw Enumeration .1.3.6.1.4.1.14179.2.4.1.7 |
bsnRrmDot11b OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.4.2 |
bsnRrmDot11bGroup OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.4.2.1 |
bsnRrmDot11bGlobalAutomaticGroupingDynamic grouping has two modes: on and off. When the grouping is off, no dynamic grouping occurs. Each Airespace Switch optimizes only its own Airespace APs' parameters. When grouping is on, the Airespace Switchs form groups and elect leaders to perform better dynamic parameter optimization.rw Enumeration .1.3.6.1.4.1.14179.2.4.2.1.1 |
bsnRrmDot11bGroupLeaderMacAddrThis is the MAC address of the group leader for the dot11b group containing this Airespace Switch.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.4.2.1.2 |
bsnRrmIsDot11bGroupLeaderIf this Airespace Switch is a Dot11b Group Leader then this attribute will be true else it will be false.ro Enumeration .1.3.6.1.4.1.14179.2.4.2.1.3 |
bsnRrmDot11bGroupLastUpdateTimeLast time the dot11b grouping was updated on this Airespace Switch. This is valid only if the Airespace Switch is a group leader.ro Unsigned32 .1.3.6.1.4.1.14179.2.4.2.1.4 |
bsnRrmDot11bGlobalGroupIntervalWhen grouping is on, this interval(in secs) represents the period with which the grouping algorithm is run. Grouping algorithm will also run when the group contents changes and the automatic grouping is enabled. A dynamic grouping can be started upon request from the system administrator. Default value is 3600 secs.ro Unsigned32 .1.3.6.1.4.1.14179.2.4.2.1.5 |
bsnWrasDot11bGroupTableThis is a table of Airespace Switch addresses that identifies the members of the Dot11b RF group containing this Airespace Switch. Max size is 20 entries. SEQUENCE OF BsnWrasDot11bGroupEntry .1.3.6.1.4.1.14179.2.4.2.1.9 |
bsnWrasDot11bGroupEntry... BsnWrasDot11bGroupEntry .1.3.6.1.4.1.14179.2.4.2.1.9.1 |
bsnWrasDot11bPeerMacAddressThe MAC address of the GIGE interface.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.4.2.1.9.1.1 |
bsnWrasDot11bPeerIpAddressThe IP address of the Airespace Switch.ro IpAddress .1.3.6.1.4.1.14179.2.4.2.1.9.1.21 |
bsnRrmDot11bAPDefault OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.4.2.6 |
bsnRrmDot11bForeignInterferenceThresholdForeign 802.11A interference threshold between 0 and 100 percent.rw INTEGER .1.3.6.1.4.1.14179.2.4.2.6.1 |
bsnRrmDot11bForeignNoiseThreshold802.11A foreign noise threshold between -127 and 0 dBm.rw INTEGER (-127..0) .1.3.6.1.4.1.14179.2.4.2.6.2 |
bsnRrmDot11bRFUtilizationThreshold802.11A RF utlization threshold between 0 and 100 percent.rw INTEGER .1.3.6.1.4.1.14179.2.4.2.6.3 |
bsnRrmDot11bThroughputThreshold802.11A Airespace AP data-rate threshold between 1000 and 100000rw Unsigned32 .1.3.6.1.4.1.14179.2.4.2.6.4 |
bsnRrmDot11bMobilesThreshold802.11A Airespace AP mobiles threshold between 1 and 75rw INTEGER .1.3.6.1.4.1.14179.2.4.2.6.5 |
bsnRrmDot11bCoverageThreshold802.11A Airespace AP coverage threshold between 3 and 50.rw INTEGER .1.3.6.1.4.1.14179.2.4.2.6.6 |
bsnRrmDot11bMobileMinExceptionLevel802.11A Airespace AP mobile minimum exception level between 1 and 75rw INTEGER .1.3.6.1.4.1.14179.2.4.2.6.7 |
bsnRrmDot11bCoverageExceptionLevel802.11A Airespace AP coverage exception level between 0 and 100 percent.rw INTEGER .1.3.6.1.4.1.14179.2.4.2.6.8 |
bsnRrmDot11bSignalMeasurementIntervalThis interval( in secs) specifies how often do we get new signal strength measurements at each Airespace AP. Default is 300 secsrw Unsigned32 .1.3.6.1.4.1.14179.2.4.2.6.9 |
bsnRrmDot11bNoiseMeasurementIntervalThis interval( in secs) specifies how often do we get new noise and interference measurements at each Airespace AP. Default is 300 secsrw Unsigned32 .1.3.6.1.4.1.14179.2.4.2.6.10 |
bsnRrmDot11bLoadMeasurementIntervalThis interval( in secs) specifies how often do we get new load measurements at each Airespace AP. Default is 300 secsrw Unsigned32 .1.3.6.1.4.1.14179.2.4.2.6.11 |
bsnRrmDot11bCoverageMeasurementIntervalThis interval( in secs) specifies how often do we get new coverage measurements at each Airespace AP. Default is 300 secsrw Unsigned32 .1.3.6.1.4.1.14179.2.4.2.6.12 |
bsnRrmDot11bChannelMonitorListThis attribute specifies the channels on which the switch monitors noise, interference and rogues. The first option allows monitoring on all channels while the second one on only those that are supported by the country of operation. the option dca implies that the monitor channel list will include those channels that are used by automatic channel assignment.rw Enumeration .1.3.6.1.4.1.14179.2.4.2.6.13 |
bsnRrmDot11bSetFactoryDefaultWhen set to activate all rrm parameters are reset to factory defaultsrw Enumeration .1.3.6.1.4.1.14179.2.4.2.7 |
bsnAAA OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.5 |
bsnRadiusAuthServerTableThe (conceptual) table listing the RADIUS authentication servers with which the client shares a secret. SEQUENCE OF BsnRadiusAuthServerEntry .1.3.6.1.4.1.14179.2.5.1 |
bsnRadiusAuthServerEntryAn entry (conceptual row) representing a RADIUS authentication server with which the client shares a secret. BsnRadiusAuthServerEntry .1.3.6.1.4.1.14179.2.5.1.1 |
bsnRadiusAuthServerIndexA number uniquely identifying each RADIUS Authentication server with which this client communicates.rw Integer32 .1.3.6.1.4.1.14179.2.5.1.1.1 |
bsnRadiusAuthServerAddressThe IP address of the RADIUS authentication server referred to in this table entry.rw IpAddress .1.3.6.1.4.1.14179.2.5.1.1.2 |
bsnRadiusAuthClientServerPortNumberThe UDP port the client is using to send requests to this server.rw Integer32 .1.3.6.1.4.1.14179.2.5.1.1.3 |
bsnRadiusAuthServerKeyThe authentication and encryption key shared between the Radius client and this Radius Server. When the bsnRadiusAuthServerKeyFormat is hex it can have max length of 128 bytes. If the bsnRadiusAuthServerKeyFormat is Ascii it can have max length of 64 bytes.rw OCTET STRING .1.3.6.1.4.1.14179.2.5.1.1.4 |
bsnRadiusAuthServerStatusServer enable or disable status.rw Enumeration .1.3.6.1.4.1.14179.2.5.1.1.5 |
bsnRadiusAuthServerKeyFormatFormat of the server key. When hex, the number of characters in the key should be even.rw Enumeration .1.3.6.1.4.1.14179.2.5.1.1.6 |
bsnRadiusAuthServerRFC3576Support for Dynamic Authorization Extensions to RADIUS.rw Enumeration .1.3.6.1.4.1.14179.2.5.1.1.7 |
bsnRadiusAuthServerIPSecIPSec over RADIUSrw Enumeration .1.3.6.1.4.1.14179.2.5.1.1.8 |
bsnRadiusAuthServerIPSecAuthThe Hash algorithm employed by the IPSec Encrpytion. This applies only when bsnRadiusAuthServerIPSec is in enable state.rw Enumeration .1.3.6.1.4.1.14179.2.5.1.1.9 |
bsnRadiusAuthServerIPSecEncryptionThe Encryption algorithm employed by this IpSec Encryption. This applies only when bsnRadiusAuthServerIPSec is in enable state.rw Enumeration .1.3.6.1.4.1.14179.2.5.1.1.10 |
bsnRadiusAuthServerIPSecIKEPhase1VPN IKE Phase 1 Mode type as per the IpSec standards. This applies only when bsnRadiusAuthServerIPSec is in enable state.rw Enumeration .1.3.6.1.4.1.14179.2.5.1.1.11 |
bsnRadiusAuthServerIPSecIKELifetimeIPSec IKE's Lifetime. This applies only when bsnRadiusAuthServerIPSec is in enable state.rw Integer32 .1.3.6.1.4.1.14179.2.5.1.1.12 |
bsnRadiusAuthServerIPSecDHGroupIKE's Diffie-Hellman Group. This applies only when bsnRadiusAuthServerIPSec is in enable state.rw Enumeration .1.3.6.1.4.1.14179.2.5.1.1.13 |
bsnRadiusAuthServerNetworkUserConfigWhen enabled, this entry is considered as network user radius authenticating server entry.rw Enumeration .1.3.6.1.4.1.14179.2.5.1.1.14 |
bsnRadiusAuthServerMgmtUserConfigWhen enabled, this entry is considered as management user radius authenticating server entry.rw Enumeration .1.3.6.1.4.1.14179.2.5.1.1.15 |
bsnRadiusAuthServerRetransmitTimeoutTime in seconds after which a radius authentication request will timeout and a retransmission will be taken up by the switch.rw INTEGER .1.3.6.1.4.1.14179.2.5.1.1.17 |
bsnRadiusAuthServerKeyWrapKEKkeyKey-encryption-key (KEK) used as the key for the 128 bit AES Key Wrap algorithm to encrypt the PMK in the key attribute. If the key is present in request, it should be taken as a hint by the server that the sender prefers this method of encryption over others. To maintain security actual keys after configuration are never returned in get request. If keys are configured then '***' is returned. If keys are not configured then empty string is retunred. bsnRadiusAuthServerKeyFormat is used this key. if the format chosen is ascii then it should be 16 bytes in length. if the format chosen is hex then it should be 32 bytes in length.rw OCTET STRING .1.3.6.1.4.1.14179.2.5.1.1.18 |
bsnRadiusAuthServerKeyWrapMACKkeyMessage-authenticator-code-key ( MACK) - used as the key for the HMAC-SHA-1 algorithm to sign the RADIUS message to prevent spoofing. MACK must be configured when KEK is configured. To maintain security actual keys after configuration are never returned in get request. If keys are configured then '***' is returned. If keys are not configured then empty string is returned. bsnRadiusAuthServerKeyFormat is used this key. if the format chosen is ascii then it should be 20 bytes in length. If the format chosen is hex then it should be 40 bytes in length.rw OCTET STRING .1.3.6.1.4.1.14179.2.5.1.1.19 |
bsnRadiusAuthServerKeyWrapFormatFormat for the Key Wrap keys. This object is mandatory for manager to send if the key Wrap keys are being configured. Get on this object will always return hex(1)rw Enumeration .1.3.6.1.4.1.14179.2.5.1.1.20 |
bsnRadiusAuthServerRowStatusRow Status for creation/deletionrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.5.1.1.26 |
bsnRadiusAccServerTableThe (conceptual) table listing the RADIUS accounting servers with which the client shares a secret. SEQUENCE OF BsnRadiusAccServerEntry .1.3.6.1.4.1.14179.2.5.2 |
bsnRadiusAccServerEntryAn entry (conceptual row) representing a RADIUS accounting server with which the client shares a secret. BsnRadiusAccServerEntry .1.3.6.1.4.1.14179.2.5.2.1 |
bsnRadiusAccServerIndexA number uniquely identifying each RADIUS Accounting server with which this client communicates.rw Integer32 .1.3.6.1.4.1.14179.2.5.2.1.1 |
bsnRadiusAccServerAddressThe IP address of the RADIUS accounting server referred to in this table entry.rw IpAddress .1.3.6.1.4.1.14179.2.5.2.1.2 |
bsnRadiusAccClientServerPortNumberThe UDP port the client is using to send requests to this server.rw Integer32 .1.3.6.1.4.1.14179.2.5.2.1.3 |
bsnRadiusAccServerKeyThe authentication and encryption key shared between the Radius client and this Radius Server. When the bsnRadiusAccServerKeyFormat is hex it can have max length of 128 bytes. If the bsnRadiusAccServerKeyFormat is Ascii it can have max length of 64 bytes.rw OCTET STRING .1.3.6.1.4.1.14179.2.5.2.1.4 |
bsnRadiusAccServerStatusServer enable or disable status.rw Enumeration .1.3.6.1.4.1.14179.2.5.2.1.5 |
bsnRadiusAccServerKeyFormatFormat of the server key. When hex, the number of characters in the key should be even.rw Enumeration .1.3.6.1.4.1.14179.2.5.2.1.6 |
bsnRadiusAccServerIPSecIPSec over RADIUSrw Enumeration .1.3.6.1.4.1.14179.2.5.2.1.7 |
bsnRadiusAccServerIPSecAuthThe Hash algorithm employed by the IPSec Encrpytion. This applies only when bsnRadiusAccServerIPSec is in enable state.rw Enumeration .1.3.6.1.4.1.14179.2.5.2.1.8 |
bsnRadiusAccServerIPSecEncryptionThe Encryption algorithm employed by this IpSec Encryption. This applies only when bsnRadiusAccServerIPSec is in enable state.rw Enumeration .1.3.6.1.4.1.14179.2.5.2.1.9 |
bsnRadiusAccServerIPSecIKEPhase1VPN IKE Phase 1 Mode type as per the IpSec standards. This applies only when bsnRadiusAccServerIPSec is in enable state.rw Enumeration .1.3.6.1.4.1.14179.2.5.2.1.10 |
bsnRadiusAccServerIPSecIKELifetimeIPSec IKE's Lifetime. This applies only when bsnRadiusAccServerIPSec is in enable state.rw Integer32 .1.3.6.1.4.1.14179.2.5.2.1.11 |
bsnRadiusAccServerIPSecDHGroupIKE's Diffie-Hellman Group. This applies only when bsnRadiusAccServerIPSec is in enable state.rw Enumeration .1.3.6.1.4.1.14179.2.5.2.1.12 |
bsnRadiusAccServerNetworkUserConfigWhen enabled, this entry is considered as network user radius accounting server entry.rw Enumeration .1.3.6.1.4.1.14179.2.5.2.1.13 |
bsnRadiusAccServerRetransmitTimeoutTime in seconds after which a radius accounting request will timeout and a retransmission will be taken up by the switch.rw INTEGER .1.3.6.1.4.1.14179.2.5.2.1.14 |
bsnRadiusAccServerRowStatusRow Status for creation/deletionrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.5.2.1.26 |
bsnRadiusAuthServerStatsTableThe listing the Statistics of RADIUS authentication servers. SEQUENCE OF BsnRadiusAuthServerStatsEntry .1.3.6.1.4.1.14179.2.5.3 |
bsnRadiusAuthServerStatsEntryAn entry representing statistics a RADIUS authentication server with which the client shares a secret. BsnRadiusAuthServerStatsEntry .1.3.6.1.4.1.14179.2.5.3.1 |
bsnRadiusAuthClientRoundTripTimeThe time interval (in hundredths of a second) between the most recent Access-Reply/Access-Challenge and the Access-Request that matched it from this RADIUS authentication server.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.14179.2.5.3.1.6 |
bsnRadiusAuthClientAccessRequestsThe number of RADIUS Access-Request packets sent to this server. This does not include retransmissions.ro Counter32 .1.3.6.1.4.1.14179.2.5.3.1.7 |
bsnRadiusAuthClientAccessRetransmissionsThe number of RADIUS Access-Request packets retransmitted to this RADIUS authentication server.ro Counter32 .1.3.6.1.4.1.14179.2.5.3.1.8 |
bsnRadiusAuthClientAccessAcceptsThe number of RADIUS Access-Accept packets (valid or invalid) received from this server.ro Counter32 .1.3.6.1.4.1.14179.2.5.3.1.9 |
bsnRadiusAuthClientAccessRejectsThe number of RADIUS Access-Reject packets (valid or invalid) received from this server.ro Counter32 .1.3.6.1.4.1.14179.2.5.3.1.10 |
bsnRadiusAuthClientAccessChallengesThe number of RADIUS Access-Challenge packets (valid or invalid) received from this server.ro Counter32 .1.3.6.1.4.1.14179.2.5.3.1.11 |
bsnRadiusAuthClientMalformedAccessResponsesThe number of malformed RADIUS Access-Response packets received from this server. Malformed packets include packets with an invalid length. Bad authenticators or Signature attributes or unknown types are not included as malformed access responses.ro Counter32 .1.3.6.1.4.1.14179.2.5.3.1.12 |
bsnRadiusAuthClientBadAuthenticatorsThe number of RADIUS Access-Response packets containing invalid authenticators or Signature attributes received from this server.ro Counter32 .1.3.6.1.4.1.14179.2.5.3.1.13 |
bsnRadiusAuthClientPendingRequestsThe number of RADIUS Access-Request packets destined for this server that have not yet timed out or received a response. This variable is incremented when an Access-Request is sent and decremented due to receipt of an Acess-Accept, Access-Reject or Access-Challenge, a timeout or retransmission.ro Gauge32 .1.3.6.1.4.1.14179.2.5.3.1.14 |
bsnRadiusAuthClientTimeoutsThe number of authentication timeouts to this server. After a timeout the client may retry to the same server, send to a different server, or give up. A retry to the same server is counted as a retransmit as well as a timeout. A send to a different server is counted as a Request as well as a timeout.ro Counter32 .1.3.6.1.4.1.14179.2.5.3.1.15 |
bsnRadiusAuthClientUnknownTypesThe number of RADIUS packets of unknown type which were received from this server on the authentication port.ro Counter32 .1.3.6.1.4.1.14179.2.5.3.1.16 |
bsnRadiusAuthClientPacketsDroppedThe number of RADIUS packets of which were received from this server on the authentication port and dropped for some other reason.ro Counter32 .1.3.6.1.4.1.14179.2.5.3.1.36 |
bsnRadiusAccServerStatsTableThe (conceptual) table listing the RADIUS accounting servers with which the client shares a secret. SEQUENCE OF BsnRadiusAccServerStatsEntry .1.3.6.1.4.1.14179.2.5.4 |
bsnRadiusAccServerStatsEntryAn entry (conceptual row) representing a RADIUS accounting server with which the client shares a secret. BsnRadiusAccServerStatsEntry .1.3.6.1.4.1.14179.2.5.4.1 |
bsnRadiusAccClientRoundTripTimeThe time interval between the most recent Accounting-Response and the Accounting-Request that matched it from this RADIUS accounting server.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.14179.2.5.4.1.6 |
bsnRadiusAccClientRequestsThe number of RADIUS Accounting-Request packets sent. This does not include retransmissions.ro Counter32 .1.3.6.1.4.1.14179.2.5.4.1.7 |
bsnRadiusAccClientRetransmissionsThe number of RADIUS Accounting-Request packets retransmitted to this RADIUS accounting server. Retransmissions include retries where the Identifier and Acct-Delay have been updated, as well as those in which they remain the same.ro Counter32 .1.3.6.1.4.1.14179.2.5.4.1.8 |
bsnRadiusAccClientResponsesThe number of RADIUS packets received on the accounting port from this server.ro Counter32 .1.3.6.1.4.1.14179.2.5.4.1.9 |
bsnRadiusAccClientMalformedResponsesThe number of malformed RADIUS Accounting-Response packets received from this server. Malformed packets include packets with an invalid length. Bad authenticators and unknown types are not included as malformed accounting responses.ro Counter32 .1.3.6.1.4.1.14179.2.5.4.1.10 |
bsnRadiusAccClientBadAuthenticatorsThe number of RADIUS Accounting-Response packets which contained invalid authenticators received from this server.ro Counter32 .1.3.6.1.4.1.14179.2.5.4.1.11 |
bsnRadiusAccClientPendingRequestsThe number of RADIUS Accounting-Request packets sent to this server that have not yet timed out or received a response. This variable is incremented when an Accounting-Request is sent and decremented due to receipt of an Accounting-Response, a timeout or a retransmission.ro Gauge32 .1.3.6.1.4.1.14179.2.5.4.1.12 |
bsnRadiusAccClientTimeoutsThe number of accounting timeouts to this server. After a timeout the client may retry to the same server, send to a different server, or give up. A retry to the same server is counted as a retransmit as well as a timeout. A send to a different server is counted as an Accounting-Request as well as a timeout.ro Counter32 .1.3.6.1.4.1.14179.2.5.4.1.13 |
bsnRadiusAccClientUnknownTypesThe number of RADIUS packets of unknown type which were received from this server on the accounting port.ro Counter32 .1.3.6.1.4.1.14179.2.5.4.1.14 |
bsnRadiusAccClientPacketsDroppedThe number of RADIUS packets which were received from this server on the accounting port and dropped for some other reason.ro Counter32 .1.3.6.1.4.1.14179.2.5.4.1.34 |
bsnUsersTableThe (conceptual) table listing Wlan Usersobsolete SEQUENCE OF BsnUsersEntry .1.3.6.1.4.1.14179.2.5.5 |
bsnUsersEntry....obsolete BsnUsersEntry .1.3.6.1.4.1.14179.2.5.5.1 |
bsnUserNameUser Namerwobsolete OCTET STRING .1.3.6.1.4.1.14179.2.5.5.1.2 |
bsnUserPasswordUser Passwordrwobsolete OCTET STRING .1.3.6.1.4.1.14179.2.5.5.1.3 |
bsnUserEssIndexUser WLAN ID. Value 0 implies that this applies to any WLAN ID.rwobsolete INTEGER .1.3.6.1.4.1.14179.2.5.5.1.4 |
bsnUserAccessModeUser Access Mode.rwobsolete Enumeration .1.3.6.1.4.1.14179.2.5.5.1.5 |
bsnUserTypeUser Type.rwobsolete Enumeration .1.3.6.1.4.1.14179.2.5.5.1.6 |
bsnUserInterfaceNameInterface Name.rwobsolete OCTET STRING .1.3.6.1.4.1.14179.2.5.5.1.7 |
bsnUserRowStatusRow Statusrwobsolete RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.5.5.1.26 |
bsnBlackListClientTableThe table listing Wlan Black Listed Clients SEQUENCE OF BsnBlackListClientEntry .1.3.6.1.4.1.14179.2.5.6 |
bsnBlackListClientEntry.... BsnBlackListClientEntry .1.3.6.1.4.1.14179.2.5.6.1 |
bsnBlackListClientMacAddressBlack Listed Client MAC Addressrw OCTET STRING .1.3.6.1.4.1.14179.2.5.6.1.1 |
bsnBlackListClientDescriptionBlack Listed Client Descriptionrw OCTET STRING .1.3.6.1.4.1.14179.2.5.6.1.2 |
bsnBlackListClientRowStatusRow Statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.5.6.1.22 |
bsnAclTableThe table listing ACLs (Access Control Lists) on the Switch. SEQUENCE OF BsnAclEntry .1.3.6.1.4.1.14179.2.5.7 |
bsnAclEntry.... BsnAclEntry .1.3.6.1.4.1.14179.2.5.7.1 |
bsnAclNameName of the Access Control List.rw OCTET STRING .1.3.6.1.4.1.14179.2.5.7.1.1 |
bsnAclApplyModeThe apply mode of the ACL on the switch. Mode value 'applied' means the ACL has been applied on the switch.ro Enumeration .1.3.6.1.4.1.14179.2.5.7.1.2 |
bsnAclRowStatusRow Status of the ACL.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.5.7.1.20 |
bsnAclRuleTableThe table listing Acl Rules(Access Control List Entries) on the ACL with name bsnAclName. SEQUENCE OF BsnAclRuleEntry .1.3.6.1.4.1.14179.2.5.8 |
bsnAclRuleEntry.... BsnAclRuleEntry .1.3.6.1.4.1.14179.2.5.8.1 |
bsnAclRuleIndexIndex of the ACL rule. This can be updated to reset the sequence of the rules of an ACL.rw Unsigned32 .1.3.6.1.4.1.14179.2.5.8.1.2 |
bsnAclRuleActionThe permission mode of a rule.rw Enumeration .1.3.6.1.4.1.14179.2.5.8.1.3 |
bsnAclRuleDirectionThe direction of the packet to which the rule may be applied.rw Enumeration .1.3.6.1.4.1.14179.2.5.8.1.4 |
bsnAclRuleSourceIpAddressSource IP Address of the ACL rule. A value 0 implies any source address.rw IpAddress .1.3.6.1.4.1.14179.2.5.8.1.5 |
bsnAclRuleSourceIpNetmaskSource IP Netmask of the ACL rule. A value 0 implies any source mask.rw IpAddress .1.3.6.1.4.1.14179.2.5.8.1.6 |
bsnAclRuleDestinationIpAddressDestination IP Address of the ACL rule. A value 0 implies any destination address.rw IpAddress .1.3.6.1.4.1.14179.2.5.8.1.7 |
bsnAclRuleDestinationIpNetmaskDestination Netmask of the ACL rule. A value 0 implies any destination mask.rw IpAddress .1.3.6.1.4.1.14179.2.5.8.1.8 |
bsnAclRuleProtocolProtocol of the packet. It can be either of the pre specified protocols like TCP, UDP, ICMP, ESP, AH, GRE, IP, Ethernet Over IP, OSPF or any number between 0 and 255. A value 256 implies that this rule applies to 'Any' protocol.rw Unsigned32 .1.3.6.1.4.1.14179.2.5.8.1.9 |
bsnAclRuleStartSourcePortSource Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule applies to 'Any' source port. This value can be set only if the protocol is set to TCP or UDP. Otherwise the value is set to Any(65536)rw Unsigned32 .1.3.6.1.4.1.14179.2.5.8.1.10 |
bsnAclRuleEndSourcePortSource Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule applies to 'Any' source port. This value can be set only if the protocol is set to TCP or UDP. Otherwise the value is set to Any(65536)rw Unsigned32 .1.3.6.1.4.1.14179.2.5.8.1.11 |
bsnAclRuleStartDestinationPortDestination Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule aplpies to 'Any' Destination port. This value can be set only if the protocol is set to TCP or UDP. Otherwise the value is set to Any(65536)rw Unsigned32 .1.3.6.1.4.1.14179.2.5.8.1.12 |
bsnAclRuleEndDestinationPortDestination Port of the packet. It can be either of the pre specified ports like HTTP, HTTPS, Telnet, RADIUS etc or any number between 0 and 65535. A value 65536 implies that this rule aplpies to 'Any' Destination port. This value can be set only if the protocol is set to TCP or UDP. Otherwise the value is set to Any(65536)rw Unsigned32 .1.3.6.1.4.1.14179.2.5.8.1.13 |
bsnAclRuleDscpDSCP value of the rule. A value 256 implies Anyrw Unsigned32 .1.3.6.1.4.1.14179.2.5.8.1.14 |
bsnAclNewRuleIndexNew Index of the ACL rule. This attribute should be updated if the requirement is to reset the sequence of the rules of an ACL. A read on this will not yield anything.rw Unsigned32 .1.3.6.1.4.1.14179.2.5.8.1.15 |
bsnAclRuleRowStatusRow Status of the ACL Rule.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.5.8.1.40 |
bsnMacFilterTableThe table listing MAC Filter entries SEQUENCE OF BsnMacFilterEntry .1.3.6.1.4.1.14179.2.5.9 |
bsnMacFilterEntry.... BsnMacFilterEntry .1.3.6.1.4.1.14179.2.5.9.1 |
bsnMacFilterAddressMAC Address of the entryrw OCTET STRING .1.3.6.1.4.1.14179.2.5.9.1.1 |
bsnMacFilterWlanIdWLAN ID of the WLAN that the user can connect to. 0 means any WLAN ID.rw INTEGER .1.3.6.1.4.1.14179.2.5.9.1.2 |
bsnMacFilterInterfaceNameInterface Name.rw OCTET STRING .1.3.6.1.4.1.14179.2.5.9.1.3 |
bsnMacFilterDescriptionDescription of the MAC Filter entry.rw OCTET STRING .1.3.6.1.4.1.14179.2.5.9.1.4 |
bsnMacFilterRowStatusRow Statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.5.9.1.24 |
bsnLocalNetUserTableThe table listing Local Net User entries. SEQUENCE OF BsnLocalNetUserEntry .1.3.6.1.4.1.14179.2.5.10 |
bsnLocalNetUserEntry.... BsnLocalNetUserEntry .1.3.6.1.4.1.14179.2.5.10.1 |
bsnLocalNetUserNameName of the net user.rw OCTET STRING .1.3.6.1.4.1.14179.2.5.10.1.1 |
bsnLocalNetUserWlanIdWLAN ID of the WLAN that the user can connect to. 0 means any WLAN ID.rw INTEGER .1.3.6.1.4.1.14179.2.5.10.1.2 |
bsnLocalNetUserPasswordUser Password.rw OCTET STRING .1.3.6.1.4.1.14179.2.5.10.1.3 |
bsnLocalNetUserDescriptionDescription of the Net User entry.rw OCTET STRING .1.3.6.1.4.1.14179.2.5.10.1.4 |
bsnLocalNetUserLifetimeThis object indicates the lifetime of an user account expressed in hundredths of a second. Lifetime period other than 0 will make it a guest-user. Minimum value for guest user is 60 seconds (6000). Once configured as non-guest user can not be change to guest user and vice-versa. Default value is for a day and max lifetime is 259200000(30 days). WLANIds, which have webauth policy are valid for guest access user.rw TimeInterval (0 | 6000..259200000) .1.3.6.1.4.1.14179.2.5.10.1.5 |
bsnLocalNetUserStartTimeThis object indicates the time when the guest user account was created and expressed as the number of seconds elapsed since 1st Jan, 1970.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.14179.2.5.10.1.6 |
bsnLocalNetUserRemainingTimeThis object indicates the remaining session time for the guest user in hundredths of a second.ro TimeInterval (SNMPv2-TC) .1.3.6.1.4.1.14179.2.5.10.1.7 |
bsnLocalNetUserRowStatusRow Statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.5.10.1.24 |
bsnLocalManagementUserTableThe (conceptual) table listing Local Management Users SEQUENCE OF BsnLocalManagementUserEntry .1.3.6.1.4.1.14179.2.5.11 |
bsnLocalManagementUserEntry.... BsnLocalManagementUserEntry .1.3.6.1.4.1.14179.2.5.11.1 |
bsnLocalManagementUserNameUser Namerw OCTET STRING .1.3.6.1.4.1.14179.2.5.11.1.1 |
bsnLocalManagementUserPasswordUser Passwordrw OCTET STRING .1.3.6.1.4.1.14179.2.5.11.1.2 |
bsnLocalManagementUserAccessModeUser Access Mode.rw Enumeration .1.3.6.1.4.1.14179.2.5.11.1.3 |
bsnLocalManagementUserRowStatusRow Statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.5.11.1.23 |
bsnRadiusAuthKeyWrapEnableWhen keyWrap is enable then for 801.1X and 802.11i client Authentication, request is sent to those radius servers which has KEK and MACK keys are configured. Radius servers are widely used for user authentications. In 802.11i and 802.1X type authentication, the controller recives Pairwise Master KEy(PMK) from RADIUS sever using vendor specific RADIUS attributes, which uses MPPE RFC3078. Since MPPE uses RC4 algorithm to provide data confidentiality, it is not FIPS approved. For this RADIUS key WRAP attributes, bsnRadiusAuthServerKeyWrap and bsnRadiusAuthServerKeyWrapMACKkey have been added, which are used to securely transfer encryption keys using non-proprietary techniques.rw TruthValue (SNMPv2-TC) .1.3.6.1.4.1.14179.2.5.12 |
bsnRadiusAuthCacheCredentialsLocallyEnable or disable caching of credentials locally for RADIUS Auth servers. This is used when a client uses a one time password authentication scheme.rwdeprecated Enumeration .1.3.6.1.4.1.14179.2.5.14 |
bsnAAAMacDelimiterThe delimiter to be used for mac filtering. It can be colon as in xx:xx:xx:xx:xx:xx or hyphen as in xx-xx-xx-xx-xx-xx or single hyphen as in xxxxxx-xxxxxx or no delimiter as in xxxxxxxxxxxx.rw Enumeration .1.3.6.1.4.1.14179.2.5.15 |
bsnAAARadiusCompatibilityModeThe required compatibility mode for MAC filtering. For ciscoACS, the expected MAC delimiter setting is colon and for orinocoRadius, it is singleHyphen.rw Enumeration .1.3.6.1.4.1.14179.2.5.16 |
bsnAAARadiusCallStationIdTypeThis attribute configures the call station ID information sent in RADIUS messages. The value undefined cannot be set during the write operation.rw Enumeration .1.3.6.1.4.1.14179.2.5.17 |
bsnExternalPolicyServerAclNameThis attribute configures the ACL Name for External Policy Serversrw DisplayString .1.3.6.1.4.1.14179.2.5.18 |
bsnExternalPolicyServerTableThe (conceptual) table listing the External Policy servers with which client share a secret.obsolete SEQUENCE OF BsnExternalPolicyServerEntry .1.3.6.1.4.1.14179.2.5.19 |
bsnExternalPolicyServerEntryAn entry (conceptual row) representing an External policy server with which the client shares a secret.obsolete BsnExternalPolicyServerEntry .1.3.6.1.4.1.14179.2.5.19.1 |
bsnExternalPolicyServerIndexA number uniquely identifying each External Policy server with which this client communicates.rwobsolete Integer32 .1.3.6.1.4.1.14179.2.5.19.1.1 |
bsnExternalPolicyServerAddressThe IP address of the External Policy server referred to in this table entry.rwobsolete IpAddress .1.3.6.1.4.1.14179.2.5.19.1.2 |
bsnExternalPolicyServerPortNumberThe UDP port the client is using to send requests to this server.rwobsolete Integer32 .1.3.6.1.4.1.14179.2.5.19.1.3 |
bsnExternalPolicyServerKeyThe authentication and encryption key shared between the client and this External Policy Server.rwobsolete OCTET STRING .1.3.6.1.4.1.14179.2.5.19.1.4 |
bsnExternalPolicyServerAdminStatusServer enable or disable status.rwobsolete Enumeration .1.3.6.1.4.1.14179.2.5.19.1.5 |
bsnExternalPolicyServerConnectionStatusServer enable or disable status.roobsolete Enumeration .1.3.6.1.4.1.14179.2.5.19.1.6 |
bsnExternalPolicyServerRowStatusRow Status for creation/deletionrwobsolete RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.5.19.1.26 |
bsnAAALocalDatabaseSizeThis attribute is the total number of entries permitted in the local users database. This is the combined total of entries for Local Management Users, Local Net Users, Disabled Clients (previously known as blacklistclients and the MAC Filters. If the database size limit is reached, no more entries in any of these user lists are allowed to be created. To continue creating more entries, one should increase the size of the database. This value is applied on reboot and then matches the bsnAACurrentLocalDatabaseSize.rw Integer32 .1.3.6.1.4.1.14179.2.5.20 |
bsnAAACurrentLocalDatabaseSizeThis attribute is the maximum number of entries in the local users database that is effective currently. This is the combined total of entries for Local Management Users, Local Net Users, Disabled Clients (previously known as blacklist clients) and the MAC Filters.ro Integer32 .1.3.6.1.4.1.14179.2.5.21 |
bsnAPAuthorizationTableThe table listing AP Authorization entries SEQUENCE OF BsnAPAuthorizationEntry .1.3.6.1.4.1.14179.2.5.22 |
bsnAPAuthorizationEntryBsnAPAuthorizationEntry BsnAPAuthorizationEntry .1.3.6.1.4.1.14179.2.5.22.1 |
bsnAPAuthMacAddressMAC Address of the AP entryrw OCTET STRING .1.3.6.1.4.1.14179.2.5.22.1.1 |
bsnAPAuthCertificateTypeSupported certificate types are MIC, SSC (Self-Signed-Certificate) or no certificate.rw Enumeration .1.3.6.1.4.1.14179.2.5.22.1.2 |
bsnAPAuthHashKeySHA1 hash key for SSC certificate validation. It has to be 40 hexa-decimal characters. This is considered when certificate type is SSC.rw OCTET STRING .1.3.6.1.4.1.14179.2.5.22.1.3 |
bsnAPAuthRowStatusRow Statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.5.22.1.20 |
bsnTrap OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.6 |
bsnTrapControl OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.6.1 |
bsnDot11StationTrapControlMaskThis mask describes what events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event occurence. Event corresponding value ----- ----------------- bsnDot11StationDisassociate 1 bsnDot11StationDeauthenticate 2 bsnDot11StationAuthenticateFail 4 bsnDot11StationAssociateFail 8 bsnDot11StationBlacklisted 16 bsnDot11StationAssociate 32 ciscoLwappDot11ClientMovedToRunState 64 By Default all bits are off.rw Unsigned32 .1.3.6.1.4.1.14179.2.6.1.1 |
bsnAPTrapControlMaskThis mask describes what events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event occurance. Event corresponding bit ----- ----------------- bsnAPAssociate/Disassociate 1 bsnAPIfUp/Down 4 bsnAPAuthorizationFailureCause 16 By Default all bits are on.rw Unsigned32 .1.3.6.1.4.1.14179.2.6.1.2 |
bsnAPProfileTrapControlMaskThis mask describes what events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event occurance. Event corresponding bit ----- ----------------- LoadProfileFail 1 NoiseProfileFail 2 InterferenceProfileFail 4 CoverageProfileFailed 8rw Unsigned32 .1.3.6.1.4.1.14179.2.6.1.3 |
bsnAPParamUpdateTrapControlMaskMac Parameters are updated for a Airespace AP interface whenever Dynamic Algorithm are run. This mask describes what update events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event occurance. Event corresponding bit ----- ----------------- TxPowerChange 1 ChannelChange 2 AntennaChange 4 RTSCTSThresholdChange 8 EDThresholdChange 16 FragmentationThresholdChange 32rw Unsigned32 .1.3.6.1.4.1.14179.2.6.1.4 |
bsnIpsecTrapsMaskThis mask describes what events merit traps to network management. If the bit for a particular event is turned on then notification will be generated on event occurance. Event corresponding bit ----- ----------------- bsnIpsecEspAuthFailureTrap 1 bsnIpsecEspReplayFailureTrap 2 bsnIpsecEspPolicyFailureTrap 4 bsnIpsecEspInvalidSpiTrap 8 bsnIpsecOtherPolicyFailureTrap 16 bsnIpsecIkeNegFailure 32 bsnIpsecSuiteNegFailure 64 bsnIpsecInvalidCookieTrap 128rw Unsigned32 .1.3.6.1.4.1.14179.2.6.1.5 |
bsnRogueAPTrapEnableIf Rogue AP Detection and Removed Traps need to be sentrw Enumeration .1.3.6.1.4.1.14179.2.6.1.6 |
bsnRADIUSServerTrapEnableif RADIUS Server Traps need to be sentrw Enumeration .1.3.6.1.4.1.14179.2.6.1.7 |
bsnAuthenticationFailureTrapEnableIf Authentication Failure Traps need to be sentrw Enumeration .1.3.6.1.4.1.14179.2.6.1.8 |
bsnConfigSaveTrapEnableIf Rogue AP Detection and Removed Traps need to be sentrw Enumeration .1.3.6.1.4.1.14179.2.6.1.9 |
bsn80211SecurityTrapControlMaskThis mask is for Security related trap controls. Event corresponding bit ----- ----------------- bsnWepKeyDecryptError 1 bsnSignatureAttackDetected 2 By Default all bits are off.rw Unsigned32 .1.3.6.1.4.1.14179.2.6.1.10 |
bsnWpsTrapControlEnableThis control is for WPS(Wireless Intrusion Protection System) related traps.rw Enumeration .1.3.6.1.4.1.14179.2.6.1.11 |
bsnTrapVariable OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.6.2 |
bsnAuthFailureUserNamero OCTET STRING .1.3.6.1.4.1.14179.2.6.2.1 |
bsnAuthFailureUserTypero Enumeration .1.3.6.1.4.1.14179.2.6.2.2 |
bsnRemoteIPv4Addressro IpAddress .1.3.6.1.4.1.14179.2.6.2.3 |
bsnIpsecErrorCountro Integer32 .1.3.6.1.4.1.14179.2.6.2.4 |
bsnIpsecSPIro Integer32 .1.3.6.1.4.1.14179.2.6.2.5 |
bsnRemoteUdpPortro Integer32 .1.3.6.1.4.1.14179.2.6.2.6 |
bsnIkeAuthMethodro Integer32 .1.3.6.1.4.1.14179.2.6.2.7 |
bsnIkeTotalInitFailuresro Integer32 .1.3.6.1.4.1.14179.2.6.2.8 |
bsnIkeTotalInitNoResponsesro Integer32 .1.3.6.1.4.1.14179.2.6.2.9 |
bsnIkeTotalRespFailuresro Integer32 .1.3.6.1.4.1.14179.2.6.2.10 |
bsnNotifiesSentro Integer32 .1.3.6.1.4.1.14179.2.6.2.11 |
bsnNotifiesReceivedro Integer32 .1.3.6.1.4.1.14179.2.6.2.12 |
bsnSuiteInitFailuresro Integer32 .1.3.6.1.4.1.14179.2.6.2.13 |
bsnSuiteRespondFailuresro Integer32 .1.3.6.1.4.1.14179.2.6.2.14 |
bsnInitiatorCookieThe initiator cookie used in an ISAKMP message, to be associated with a trap.ro OCTET STRING .1.3.6.1.4.1.14179.2.6.2.15 |
bsnResponderCookieThe responder cookie used in an ISAKMP message, to be associated with a trap.ro OCTET STRING .1.3.6.1.4.1.14179.2.6.2.16 |
bsnIsakmpInvalidCookiesro Integer32 .1.3.6.1.4.1.14179.2.6.2.17 |
bsnCurrentRadiosCountro Integer32 .1.3.6.1.4.1.14179.2.6.2.18 |
bsnLicenseRadioCountro Integer32 .1.3.6.1.4.1.14179.2.6.2.19 |
bsnAPMacAddrTrapVariablero MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.6.2.20 |
bsnAPNameTrapVariablero DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.6.2.21 |
bsnAPSlotIdTrapVariableNumber of Radio Interfaces on the Airespace AP.ro Integer32 .1.3.6.1.4.1.14179.2.6.2.22 |
bsnAPChannelNumberTrapVariablero Integer32 .1.3.6.1.4.1.14179.2.6.2.23 |
bsnAPCoverageThresholdTrapVariablero Integer32 .1.3.6.1.4.1.14179.2.6.2.24 |
bsnAPCoverageFailedClientsro Integer32 .1.3.6.1.4.1.14179.2.6.2.25 |
bsnAPCoverageTotalClientsro Integer32 .1.3.6.1.4.1.14179.2.6.2.26 |
bsnClientMacAddrro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.6.2.27 |
bsnClientRssiro Integer32 .1.3.6.1.4.1.14179.2.6.2.28 |
bsnClientSnrro Integer32 .1.3.6.1.4.1.14179.2.6.2.29 |
bsnInterferenceEnergyBeforeChannelUpdatero Integer32 .1.3.6.1.4.1.14179.2.6.2.30 |
bsnInterferenceEnergyAfterChannelUpdatero Integer32 .1.3.6.1.4.1.14179.2.6.2.31 |
bsnAPPortNumberTrapVariablero Integer32 .1.3.6.1.4.1.14179.2.6.2.32 |
bsnMaxRogueCountro Integer32 .1.3.6.1.4.1.14179.2.6.2.33 |
bsnStationMacAddressro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.6.2.34 |
bsnStationAPMacAddrro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.6.2.35 |
bsnStationAPIfSlotIdro INTEGER .1.3.6.1.4.1.14179.2.6.2.36 |
bsnStationReasonCodero Enumeration .1.3.6.1.4.1.14179.2.6.2.37 |
bsnStationBlacklistingReasonCodero Enumeration .1.3.6.1.4.1.14179.2.6.2.38 |
bsnStationUserNameThe user name of a client. This is used for the Client Associated trap. It may be null when not known.ro DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.6.2.39 |
bsnRogueAPOnWiredNetworkThis is the flag used on the bsnRogueAPDetected trap to state if the rogue is found on the wired network. Typically, after a rogue is found, there may be another bsnRogueAPDetected trap that will have the value of this flag 1 if the rogue is detected on the wired network.ro Enumeration .1.3.6.1.4.1.14179.2.6.2.40 |
bsnNavDosAttackSourceMacAddrMAC address generating the attack.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.6.2.41 |
bsnWlanIdTrapVariableWLAN ID used by the client when the WPA MIC error counter measure was activated.ro INTEGER .1.3.6.1.4.1.14179.2.6.2.42 |
bsnUserIpAddressro IpAddress .1.3.6.1.4.1.14179.2.6.2.43 |
bsnRogueAdhocModeThis is the flag used on the bsnRogueAPDetected trap to state if the rogue found is an Adhoc rogue or it is an AP.ro Enumeration .1.3.6.1.4.1.14179.2.6.2.44 |
bsnClearTrapVariableThis is the flag is used to indicate if this is a clear trap for the original alert or not.ro Enumeration .1.3.6.1.4.1.14179.2.6.2.45 |
bsnDuplicateIpTrapVariableThis field is used on the bsnDuplicateIpAddressReported trap to contain the IP Address in question when switch or an AP detected a duplicate IP Address on another machine.ro IpAddress .1.3.6.1.4.1.14179.2.6.2.46 |
bsnDuplicateIpTrapClearThis is the flag used to indicate clear state for the bsnDuplicateIpAddressReported trap.ro Enumeration .1.3.6.1.4.1.14179.2.6.2.47 |
bsnDuplicateIpReportedByAPThis is the flag used on the bsnDuplicateIpAddressReported trap to indicate whether the switch or an AP detected a duplicate IP Address on another machine.ro Enumeration .1.3.6.1.4.1.14179.2.6.2.48 |
bsnTrustedApRadioPolicyRequiredThis is the radio policy required by a trusted Rogue.ro Enumeration .1.3.6.1.4.1.14179.2.6.2.49 |
bsnTrustedApEncryptionUsedThis is the encryption type used by a trusted Rogue.ro Enumeration .1.3.6.1.4.1.14179.2.6.2.50 |
bsnTrustedApEncryptionRequiredThis is the encryption type required by a trusted Rogue.ro Enumeration .1.3.6.1.4.1.14179.2.6.2.51 |
bsnTrustedApRadioPolicyUsedThis is the radio policy used by a trusted Rogue.ro Enumeration .1.3.6.1.4.1.14179.2.6.2.52 |
bsnNetworkTypero Enumeration .1.3.6.1.4.1.14179.2.6.2.53 |
bsnNetworkStatero Enumeration .1.3.6.1.4.1.14179.2.6.2.54 |
bsnSignatureTypeType of Signature whose attack is detected by the switch.ro Enumeration .1.3.6.1.4.1.14179.2.6.2.55 |
bsnSignatureNameName of the Signature whose attack is detected by the switch.ro DisplayString .1.3.6.1.4.1.14179.2.6.2.56 |
bsnSignatureDescriptionDescription of the Signature whose attack is detected by the switch.ro DisplayString .1.3.6.1.4.1.14179.2.6.2.57 |
bsnImpersonatedAPMacAddrMAC Address of the AP impersonated by another AP.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.6.2.58 |
bsnTrustedApPreambleUsedThe Preamble on this detecting AP.ro Enumeration .1.3.6.1.4.1.14179.2.6.2.59 |
bsnTrustedApPreambleRequiredThe Preamble on this detecting AP.ro Enumeration .1.3.6.1.4.1.14179.2.6.2.60 |
bsnSignatureAttackPrecedThe preced in the standard/custom signature list.ro INTEGER .1.3.6.1.4.1.14179.2.6.2.61 |
bsnSignatureAttackFrequencyThe preced in the standard/custom signature list.ro INTEGER .1.3.6.1.4.1.14179.2.6.2.62 |
bsnSignatureAttackChannelThe preced in the standard/custom signature list.ro INTEGER .1.3.6.1.4.1.14179.2.6.2.63 |
bsnSignatureAttackerMacAddressThe MAC address of the Attacker's mac-interface.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.6.2.64 |
bsnLicenseKeyTrapVariableThis is the license key that has been found to be deleted, expired or is mismatched causing AP functionality to be disabled on the switch.ro OCTET STRING .1.3.6.1.4.1.14179.2.6.2.65 |
bsnApFunctionalityDisableReasonCodeThis is the reason why the AP functionality was disabled on the switch. It could be either expiry or deletion or mismatch found of the license key.ro Enumeration .1.3.6.1.4.1.14179.2.6.2.66 |
bsnLicenseKeyFeatureSetTrapVariableThis is the switch feature set whose license key has expired or is deleted or is mismatched. To enable the AP functionality again, the license key for this feature set should be re-configured.ro Enumeration .1.3.6.1.4.1.14179.2.6.2.67 |
bsnApRegulatoryDomainThe regulatory domain configured on an AP.ro Enumeration .1.3.6.1.4.1.14179.2.6.2.68 |
bsnAPAuthorizationFailureCauseThis denotes the reason for AP authorization failure. [entrydoesnotexist]: The AP has not been added to Controller's AP Authorization List. [keymismatch]: The key entry in Controller's AP Authorization list does not match the SHA1 key received from the AP. [invalidCert]: Could not verify the self signed Certificate. [entryIsMIC]: AP has Self Signed Certificate where as in Controller AP Authorization list has Manufactured Installed Certificate [aaaEntryDoesNotExist]: RADIUS authorization for the AP failed. [unknown]: Default.ro Enumeration .1.3.6.1.4.1.14179.2.6.2.69 |
bsnAPIfUpDownCauseThis denotes the reason for AP If up or down normal - radio Failure - radio failed radioLowPower - AP is not able draw enough power. maxRetransmission - max retransmission of AP Reached. echoTimeout - heartbeat timeout. configAP - admin enable/disable AP configRadio - admin enable/disable config radio configNetwork - admin enable/disable network adminConfigured - admin configuration missedRekey - Missed Rekey detectingInLinePower - Detecting in-line power newDiscovery - New Discoveryro Enumeration .1.3.6.1.4.1.14179.2.6.2.70 |
bsnAPInvalidRadioTypeRadio types which are not supported by controller.ro Enumeration .1.3.6.1.4.1.14179.2.6.2.71 |
locationNotifyContentThis is the content of the notification.ro OCTET STRING .1.3.6.1.4.1.14179.2.6.2.72 |
bsnSignatureMacInfoThis object defines the pattern followed by the LWAPP APs to perform signature analysis with this signature and report the results to the Controller.ro BsnTxtSignatureMacInfo .1.3.6.1.4.1.14179.2.6.2.73 |
bsnImpersonatingSourceMacAddrThis is the source mac address which is impersonating the AP.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.6.2.74 |
bsnAPPreviousChannelNumberTrapVariablero Integer32 .1.3.6.1.4.1.14179.2.6.2.83 |
bsnAPReasonCodeTrapVariablero Bits .1.3.6.1.4.1.14179.2.6.2.84 |
bsnNoiseBeforeChannelUpdatero Integer32 .1.3.6.1.4.1.14179.2.6.2.85 |
bsnNoiseAfterChannelUpdatero Integer32 .1.3.6.1.4.1.14179.2.6.2.86 |
bsnInterferenceBeforeChannelUpdatero Integer32 .1.3.6.1.4.1.14179.2.6.2.87 |
bsnInterferenceAfterChannelUpdatero Integer32 .1.3.6.1.4.1.14179.2.6.2.88 |
bsnTraps OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.6.3 |
bsnDot11StationDisassociateThe disassociate notification shall be sent when the Station sends a Disassociation frame. The value of the notification shall include the MAC address of the MAC to which the Disassociation frame was sent and the reason for the disassociation NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.1 |
bsnDot11StationDeauthenticateThe deauthenticate notification shall be sent when the Station sends a Deauthentication frame. The value of the notification shall include the MAC address of the MAC to which the Deauthentication frame was sent and the reason for the deauthentication. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.2 |
bsnDot11StationAuthenticateFailThe authenticate failure notification shall be sent when the Station sends an Authentication frame with a status code other than 'successful'. The value of the notification shall include the MAC address of the MAC to which the Authentication frame was sent and the reason for the authentication failure. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.3 |
bsnDot11StationAssociateFailThe associate failure notification shall be sent when the Station sends an Association frame with a status code other than 'successful'. The value of the notification shall include the MAC address of the MAC to which the Authentication frame was sent and the reason for the authentication failure. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.4 |
bsnAPUpWhen Airespace AP operation status goes up this trap will be sentobsolete NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.5 |
bsnAPDownWhen Airespace AP operation status goes down this trap will be sentobsolete NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.6 |
bsnAPAssociatedWhen Airespace AP Associates to a Airespace Switch, AP associated notification will be sent with dot3 MAC address of Airespace AP.This will help management system to discover Airespace AP and add to system.deprecated NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.7 |
bsnAPDisassociatedWhen Airespace AP disassociates from Airespace Switch, AP disassociated notification will be sent with dot3 MAC address of Airespace AP management system to remove Airespace AP from this Airespace Switch NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.8 |
bsnAPIfUpWhen Airespace AP's interface's operation status goes up this trap will be sent NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.9 |
bsnAPIfDownWhen Airespace AP's interface's operation status goes down this trap will be sent. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.10 |
bsnAPLoadProfileFailedWhen LOAD Profile state changes from PASS to FAIL, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.11 |
bsnAPNoiseProfileFailedWhen Noise Profile state changes from PASS to FAIL, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.12 |
bsnAPInterferenceProfileFailedWhen Interference Profile state changes from PASS to FAIL, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.13 |
bsnAPCoverageProfileFailedWhen Coverage Profile state changes from PASS to FAIL, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.14 |
bsnAPCurrentTxPowerChangedWhenever dynamic algorithms are running and bsnAPIfPhyPowerAutomaticOn is true, Airespace AP Interface's CurrentTxPower might get updated by algorithm. When this occurs notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF along with the currentTxPower for this Airespace AP IF NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.15 |
bsnAPCurrentChannelChangedWhenever dynamic algorithms are running and bsnAPIfPhyChannelAutomaticOn is true, Airespace AP Interface's CurrentChannel might get updated by algorithm. When this occurs notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF along with the currentChannel for this Airespace AP IF NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.16 |
bsnRrmDot11aGroupingDoneWhen Grouping is done, this notification will be sent from the previous Group Leader where grouping algorithm was run. It has MAC address of the new Group Leader. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.21 |
bsnRrmDot11bGroupingDoneWhen Grouping is done, this notification will be sent from the previous Group Leader where grouping algorithm was run. It has MAC address of the new Group Leader. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.22 |
bsnConfigSavedWhen configuration is save either from CLI or web interface This trap will be sent to inform NMS to do refresh NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.23 |
bsnDot11EssCreatedWhenever a new Ess (WLAN) is created, this notification will be sent along with EssIndex NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.24 |
bsnDot11EssDeletedWhenever a Ess (WLAN)is deleted, this notification will be sent along with EssIndex NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.25 |
bsnRADIUSServerNotRespondingThis trap is to indicate that no RADIUS server(s) are responding to authentication requests sent by the RADIUS client within the MWAR device(Switch). NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.26 |
bsnAuthenticationFailureThis trap is to inform that client authentication failure has occured at MWAR(Switch). This could be cli/web user, wlan user, or Mac Authorized user. ServiceType will indicate which type of user it is and userName will be cli/web/wlan userName or MacAddress of Mac Authorized User NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.27 |
bsnIpsecEspAuthFailureTrapIPsec packets with invalid hashes were found in an inbound ESP SA. The total number of authentication errors accumulated is sent for the specific row of the ipsecSaEspInTable table for the SA; this provides the identity of the SA in which the error occurred. Implementations SHOULD send one trap per SA (within a reasonable time period), rather than sending one trap per packet. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.28 |
bsnIpsecEspReplayFailureTrapIPsec packets with invalid sequence numbers were found in an inbound ESP SA. The total number of replay errors accumulated is sent for the specific row of the ipsecSaEspInTable table for the SA; this provides the identity of the SA in which the error occurred. Implementations SHOULD send one trap per SA (within a reasonable time period), rather than sending one trap per packet. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.29 |
bsnIpsecEspInvalidSpiTrapA packet with an unknown SPI was detected from the specified peer with the specified SPI using the specified protocol. The destination address of the received packet is specified by ipsecLocalAddress. The value ifIndex may be 0 if this optional linkage is unsupported. If the object ipsecSecurityProtocol has the value for IPcomp, then the ipsecSPI object is the CPI of the packet. Implementations SHOULD send one trap per peer (within a reasonable time period), rather than sending one trap per packet. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.31 |
bsnIpsecIkeNegFailureAn attempt to negotiate a phase 1 IKE SA failed. The notification counts are also sent as part of the trap, along with the current value of the total negotiation error counters for ISAKMP. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.33 |
bsnIpsecSuiteNegFailureAn attempt to negotiate a phase 2 SA suite for the specified selector failed. The current total failure counts are passed as well as the notification type counts for the notify involved in the failure. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.34 |
bsnIpsecInvalidCookieTrapISAKMP packets with invalid cookies were detected from the specified source, intended for the specified destination. The initiator and responder cookies are also sent with the trap. The current count is sent to allow the trap to accurately relfect dropped and throttled traps. Implementations SHOULD send one trap per peer (within a reasonable time period, rather than sending one trap per packet. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.35 |
bsnRogueAPDetectedWhen a Rogue AP is detected this Trap will be sent out along with APMacAddress on which its detected NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.36 |
bsnAPLoadProfileUpdatedToPassWhen LOAD Profile state changes from FAIL to PASSt this notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.37 |
bsnAPNoiseProfileUpdatedToPassWhen Noise Profile state changes from FAIL tp PASS, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.38 |
bsnAPInterferenceProfileUpdatedToPassWhen Interference Profile state changes from FAIL tp PASS, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable /disable using bsnRrmProfileTrapControlFlag NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.39 |
bsnAPCoverageProfileUpdatedToPassWhen Coverage Profile state changes from FAIL tp PASS, notification will be sent with Dot3 MAC address of Airespace AP and slot ID of Airespace AP IF. This trap sending can be enable/disable using bsnRrmProfileTrapControlFlag NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.40 |
bsnRogueAPRemovedWhen a Rogue AP that was detected earlier no longer exists this Trap will be sent out along with APMacAddress on which its detected NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.41 |
bsnRadiosExceedLicenseCountWhenever the currently associated Radios exceed the License Count This trap will be sent to annoy the Customer NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.42 |
bsnSensedTemperatureTooHighTemperature sensor temp too High - temp is too high on the unit. Immediate action should be taken NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.43 |
bsnSensedTemperatureTooLowTemperature sensor temp too Low - temp is too high on the unit. Immediate action should be taken NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.44 |
bsnTemperatureSensorFailureTemperature sensor hw failure - temp sensor has failed. Temperature is unknown NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.45 |
bsnTemperatureSensorClearTemperature sensor clear -- temp sensor alarm condition is over. sensor is operating within proper temp range NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.46 |
bsnPOEControllerFailurePOE Controller has failed. Its a very critical trap. User intervention is required. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.47 |
bsnMaxRogueCountExceededThe number of rogues has exceeded the maximum Rogues allowed NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.48 |
bsnMaxRogueCountClearThe number of rogues is within the maximum Rogues allowed NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.49 |
bsnApMaxRogueCountExceededThe number of rogues has exceeded the maximum Rogues allowed on the AP NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.50 |
bsnApMaxRogueCountClearThe number of rogues is within the maximum Rogues allowed on the AP NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.51 |
bsnDot11StationBlacklistedThe station blacklisted notification shall be sent when the client is blacklisted. The reason could be repeated auth or association failures or IP Address theft. The value of the notification shall include the MAC address of the MAC to which the Authentication frame was sent, the MAC and Slot Id of AP that client was associated to and the reason for black listing. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.52 |
bsnDot11StationAssociateThe associate notification shall be sent when any of the watchlisted clients(present on at least one watch list) associates with an AP. The value of the notification shall include the MAC address and the Slot ID of the radio to which the station Associated. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.53 |
bsnApBigNavDosAttackThe AP sent a string of messages with large NAV field. This is most likely a malicious denial of service attack. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.55 |
bsnTooManyUnsuccessLoginAttemptsThe Management User made too many unsuccessful login attempts. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.56 |
bsnWepKeyDecryptErrorIssued when a decrypt error occurrs. The WEP Key configured at the station may be wrong. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.57 |
bsnWpaMicErrorCounterActivatedIssued when a WPA MIC error occurs and a counter measure is activated at the AP. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.58 |
bsnRogueAPDetectedOnWiredNetworkWhen a Rogue is detected on the wired network this trap will be sent out. The same trap with bsnRogueAPOnWiredNetwork set to no will clear the previous trap. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.59 |
bsnApHasNoRadioCardsWhen an AP has no radio cards present on it, the switch sends this trap. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.60 |
bsnDuplicateIpAddressReportedThis trap is issued when the switch or an AP detects another machine using its IP Address. The first variable has value yes if the duplicate IP is reported by an AP. In that case, the second attribute will carry the AP MAC Address. The third variable is the duplicate IP address in question and the last attribute is the MAC Address of the machine that is found to be using the duplicate IP. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.61 |
bsnAPContainedAsARogueWhen our AP detects that it is being contained by another AP, this trap is issued. The clear flag is true if the AP is no longer being contained. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.62 |
bsnTrustedApHasInvalidSsidIssued when a Trusted Rogue AP is auto contained for advertising invalid SSID. If the clear variable has value true, then the trap clears the earlier alert. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.63 |
bsnTrustedApIsMissingIssued when a Trusted Rogue AP is missing or has failed. If the clear variable has value true, then the trap clears the earlier alert. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.64 |
bsnAdhocRogueAutoContainedIssued when an Adhoc Rogue is auto contained. If the clear variable has value true, then the trap clears the earlier alert. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.65 |
bsnRogueApAutoContainedIssued when a Rogue AP is auto contained for advertising our SSID. If the clear variable has value true, then the trap clears the earlier alert. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.66 |
bsnTrustedApHasInvalidEncryptionIssued when a Trusted Rogue AP is auto contained for using invalid encryption. The second param is for the encryption used and the third param is for encryption required. If the clear variable has value true, then the trap clears the earlier alert. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.67 |
bsnTrustedApHasInvalidRadioPolicyIssued when a Trusted Rogue AP is auto contained for using invalid radio policy. The second param is for the radio policy used and the third param is for radio policy required. If the clear variable has value true, then the trap clears the earlier alert. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.68 |
bsnNetworkStateChangedWhen the 802.11a or b/g network state is changed this trap is issued. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.69 |
bsnSignatureAttackDetectedThis trap is sent out when a signature attack is detected by the switch. The standard and custom signatures are predefined on the switch (see bsnSignatureConfig group). The signatures also defines if its detection should be reported. The trap variables bsnSignatureName and bsnSignatureDescription are retrieved from the detected signature definition. Clear Trap Variable is turned on when the signature attack stops. The signature's quiet time configuration speicifes the time after which the clear trap would be sent. bsnSignatureMacInfo indicates whether the signature is used to track pattern matches for all source MAC addresses together or seperately for individual source MAC addresses. bsnSignatureAttackFrequency will carry the value for a specific MAC address or for all MAC addresses depending on bsnSignatureMacInfo. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.70 |
bsnAPRadioCardTxFailureThis trap is sent by the switch when a radio card on an AP stops transmitting. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.71 |
bsnAPRadioCardTxFailureClearThis trap is sent by the switch when a radio card on an AP starts transmitting again after a prior failure. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.72 |
bsnAPRadioCardRxFailureThis trap is sent by the switch when a radio card on an AP stops receiving. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.73 |
bsnAPRadioCardRxFailureClearThis trap is sent by the switch when a radio card on an AP starts receiving again after a prior failure. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.74 |
bsnAPImpersonationDetectedThis trap is sent by the switch when a radio of an authenticated AP hears from another AP whose MAC Address neither matches that of a rogue's and nor is it an authenticated neighbor of the detecting AP. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.75 |
bsnTrustedApHasInvalidPreambleIssued when a Trusted Rogue AP is auto contained for using invalid preamble. The second param is for the preamble used and the third param is for preamble required. If the clear variable has value true, then the trap clears the earlier alert. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.76 |
bsnAPIPAddressFallbackThis trap is sent out when an AP, with the configured static ip-address, fails to establish connection with outside world and starts using DHCP as a fallback option. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.77 |
bsnAPFunctionalityDisabledThis trap is sent out when AP functionality on the switch is disabled because the License key has expired or has been deleted or doesn't match the switch image. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.78 |
bsnAPRegulatoryDomainMismatchThis trap is generated if an AP's regulatory domain doesn't match the country the switch is configured for. Due to the mismatch, the AP will fail to associate with the Switch.deprecated NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.79 |
bsnRxMulticastQueueFullThis trap indicates that the CPU's Receive Multicast Queue is Full. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.80 |
bsnRadarChannelDetectedThis trap is sent when radar signals are detected on the current channel NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.81 |
bsnRadarChannelClearedThis trap will be generated, if a radar trap has been generated earlier, after the expiry of Non-Occupancy Period. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.82 |
bsnAPAuthorizationFailureThis trap is sent out in case of authorization failure while attempting to associate the AP to the controller. bsnAPDot3MacAddress represents the mac-address of that AP. bsnAPName is name of AP NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.83 |
radioCoreDumpTrapWhen radio module in AP dumps core, it informs controller and controller generates this trap. The core file can be retrieved on demand. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.84 |
invalidRadioTrapThis trap will be generated when an AP has joined is using unsupported radio or a radio slot not currently not being used. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.85 |
countryChangeTrapThis trap will be generated when an operator changes the country of operation. New country code will be sent in trap.deprecated NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.86 |
unsupportedAPTrapThis trap will be generated when unsupported AP try to join 40xx/410x or 3500 with 64MB flash. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.87 |
heartbeatLossTrapThis trap will be generated when controller loses connection with the Supervisor Switch in which it is physically embedded and doesn't hear the heartbeat keepalives from the Supervisor. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.88 |
locationNotifyTrapThis trap will be generated by the location server for notifications of location events. NOTIFICATION-TYPE .1.3.6.1.4.1.14179.2.6.3.89 |
bsnUtility OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.7 |
bsnSyslog OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.7.1 |
bsnSyslogEnablerw Enumeration .1.3.6.1.4.1.14179.2.7.1.1 |
bsnSyslogRemoteAddressThis would be the IP Address or host namerw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.14179.2.7.1.2 |
bsnPing OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.7.2 |
bsnPingTestTablePingTest Table SEQUENCE OF BsnPingTestEntry .1.3.6.1.4.1.14179.2.7.2.1 |
bsnPingTestEntryAn Entry (conceptual row) in the bsnPingTest Table. BsnPingTestEntry .1.3.6.1.4.1.14179.2.7.2.1.1 |
bsnPingTestIdTest IDrw Integer32 .1.3.6.1.4.1.14179.2.7.2.1.1.1 |
bsnPingTestIPAddressIp Address to pingrw IpAddress .1.3.6.1.4.1.14179.2.7.2.1.1.2 |
bsnPingTestSendCountNumber of bytes sentrw Integer32 .1.3.6.1.4.1.14179.2.7.2.1.1.3 |
bsnPingTestReceivedCountNumber of bytes received.ro Integer32 .1.3.6.1.4.1.14179.2.7.2.1.1.4 |
bsnPingTestStatusStatus of the ping testro Enumeration .1.3.6.1.4.1.14179.2.7.2.1.1.5 |
bsnPingTestMaxTimeIntervalMaximum time interval in msec.ro Unsigned32 UNITS "mSec" .1.3.6.1.4.1.14179.2.7.2.1.1.6 |
bsnPingTestMinTimeIntervalMinimum time interval in msec.ro Unsigned32 UNITS "mSec" .1.3.6.1.4.1.14179.2.7.2.1.1.7 |
bsnPingTestAvgTimeIntervalAverage time interval in msec.ro Unsigned32 UNITS "mSec" .1.3.6.1.4.1.14179.2.7.2.1.1.8 |
bsnPingTestRowStatusRow Statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.7.2.1.1.25 |
bsnLinkTest OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.7.3 |
bsnLinkTestTableLinkTest Tabledeprecated SEQUENCE OF BsnLinkTestEntry .1.3.6.1.4.1.14179.2.7.3.1 |
bsnLinkTestEntryAn Entry (conceptual row) in the bsnLinkTest Table.deprecated BsnLinkTestEntry .1.3.6.1.4.1.14179.2.7.3.1.1 |
bsnLinkTestIdLink Test IDrwdeprecated Integer32 .1.3.6.1.4.1.14179.2.7.3.1.1.1 |
bsnLinkTestMacAddressMAC Address of link to testrwdeprecated MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.7.3.1.1.2 |
bsnLinkTestSendPktCountNumber of packets sent.rwdeprecated Integer32 .1.3.6.1.4.1.14179.2.7.3.1.1.3 |
bsnLinkTestSendPktLengthLength of sent packetrwdeprecated Integer32 .1.3.6.1.4.1.14179.2.7.3.1.1.4 |
bsnLinkTestReceivedPktCountNumber of received packets.rodeprecated Integer32 .1.3.6.1.4.1.14179.2.7.3.1.1.5 |
bsnLinkTestClientRSSIClient RSSI value of link.rodeprecated Integer32 .1.3.6.1.4.1.14179.2.7.3.1.1.6 |
bsnLinkTestLocalSNRLocal SNR of the linkrodeprecated Integer32 .1.3.6.1.4.1.14179.2.7.3.1.1.7 |
bsnLinkTestLocalRSSILocal RSSI of the link.rodeprecated Integer32 .1.3.6.1.4.1.14179.2.7.3.1.1.8 |
bsnLinkTestStatusStatus of the link test.rodeprecated Enumeration .1.3.6.1.4.1.14179.2.7.3.1.1.9 |
bsnLinkTestRowStatusRow Statusrwdeprecated RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.7.3.1.1.30 |
bsnMobility OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.8 |
bsnMobilityConfig OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.8.1 |
bsnMobilityProtocolPortNumPort Number on which mobility Protocol runsrw Integer32 .1.3.6.1.4.1.14179.2.8.1.1 |
bsnMobilityDynamicDiscoveryStatically Configured is always enabled if members are defined. To further enable rrm discovery, learned discovery, broadcast discovery, enable/disable this attribute.rw Enumeration .1.3.6.1.4.1.14179.2.8.1.3 |
bsnMobilityStatsResetReset mobility statistics by setting this atribute to resetNow. If you try to read this attribute value will always be 0.rw Enumeration .1.3.6.1.4.1.14179.2.8.1.4 |
bsnMobilityGroupMembersTableMWAR List (statically configured members of the mobility group) SEQUENCE OF BsnMobilityGroupMembersEntry .1.3.6.1.4.1.14179.2.8.1.10 |
bsnMobilityGroupMembersEntryAn Entry (conceptual row) in the bsnMobilityGroupMembers Table. BsnMobilityGroupMembersEntry .1.3.6.1.4.1.14179.2.8.1.10.1 |
bsnMobilityGroupMemberMacAddressMember switch MAC Addressrw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.8.1.10.1.1 |
bsnMobilityGroupMemberIPAddressMember switch IP Addressrw IpAddress .1.3.6.1.4.1.14179.2.8.1.10.1.2 |
bsnMobilityGroupMemberGroupNameMember's group name. If left empty while adding a new group member, this assumes the default mobility group name of the switch.rw DisplayString .1.3.6.1.4.1.14179.2.8.1.10.1.3 |
bsnMobilityGroupMemberRowStatusRow Statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.8.1.10.1.22 |
bsnMobilityAnchorsTableStatically configured mobility anchors SEQUENCE OF BsnMobilityAnchorsEntry .1.3.6.1.4.1.14179.2.8.1.11 |
bsnMobilityAnchorsEntryAn Entry (conceptual row) in the bsnMobilityAnchorsTable Table. BsnMobilityAnchorsEntry .1.3.6.1.4.1.14179.2.8.1.11.1 |
bsnMobilityAnchorWlanSsidLocal wlan-ssid to connect to Guest/Anchor switchrw DisplayString .1.3.6.1.4.1.14179.2.8.1.11.1.1 |
bsnMobilityAnchorSwitchIPAddressGuest/Anchor switch IP Addressrw IpAddress .1.3.6.1.4.1.14179.2.8.1.11.1.2 |
bsnMobilityAnchorRowStatusRow Statusrw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.8.1.11.1.20 |
bsnMobilityStats OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.8.2 |
bsnTotalHandoffRequestsTotal handoff requestsro Counter32 .1.3.6.1.4.1.14179.2.8.2.1 |
bsnTotalHandoffsTotal handoffsro Counter32 .1.3.6.1.4.1.14179.2.8.2.2 |
bsnCurrentExportedClientsCurrent exported client countro Counter32 .1.3.6.1.4.1.14179.2.8.2.3 |
bsnTotalExportedClientsTotal exported client countro Counter32 .1.3.6.1.4.1.14179.2.8.2.4 |
bsnCurrentImportedClientsCurrent Imported client countro Counter32 .1.3.6.1.4.1.14179.2.8.2.5 |
bsnTotalImportedClientsTotal Imported client countro Counter32 .1.3.6.1.4.1.14179.2.8.2.6 |
bsnTotalHandoffErrorsTotal handoff errorsro Counter32 .1.3.6.1.4.1.14179.2.8.2.7 |
bsnTotalCommunicationErrorsTotal communication errorsro Counter32 .1.3.6.1.4.1.14179.2.8.2.8 |
bsnMobilityGroupDirectoryTableMWAR List (statically configured members of the mobility group) SEQUENCE OF BsnMobilityGroupDirectoryEntry .1.3.6.1.4.1.14179.2.8.2.9 |
bsnMobilityGroupDirectoryEntryAn Entry (conceptual row) in the bsnMobilityGroupDirectory Table. BsnMobilityGroupDirectoryEntry .1.3.6.1.4.1.14179.2.8.2.9.1 |
bsnGroupDirectoryMemberIPAddressMwar Ip Addressro IpAddress .1.3.6.1.4.1.14179.2.8.2.9.1.1 |
bsnGroupDirectoryMemberMacAddressMwar Mac Addressro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.14179.2.8.2.9.1.2 |
bsnGroupDirectoryDicoveryTypeDiscovery type of the Group Directory.ro Enumeration .1.3.6.1.4.1.14179.2.8.2.9.1.3 |
bsnMemberCurrentAnchoredClientsCurrent anchored client countro Counter32 .1.3.6.1.4.1.14179.2.8.2.9.1.4 |
bsnMemberTotalAnchoredClientsTotal anchored client countro Counter32 .1.3.6.1.4.1.14179.2.8.2.9.1.5 |
bsnMemberCurrentExportedClientsCurrent exported client countro Counter32 .1.3.6.1.4.1.14179.2.8.2.9.1.6 |
bsnMemberTotalExportedClientsTotal exported client countro Counter32 .1.3.6.1.4.1.14179.2.8.2.9.1.7 |
bsnMemberCurrentImportedClientsCurrent Imported client countro Counter32 .1.3.6.1.4.1.14179.2.8.2.9.1.8 |
bsnMemberTotalImportedClientsTotal Imported client countro Counter32 .1.3.6.1.4.1.14179.2.8.2.9.1.9 |
bsnMemberTotalHandoffErrorsTotal handoff errorsro Counter32 .1.3.6.1.4.1.14179.2.8.2.9.1.10 |
bsnMemberTotalCommunicationErrorsTotal Communication errorsro Counter32 .1.3.6.1.4.1.14179.2.8.2.9.1.30 |
bsnTotalReceiveErrorsTotal receive errorsro Counter32 .1.3.6.1.4.1.14179.2.8.2.10 |
bsnTotalTransmitErrorsTotal Transmit errorsro Counter32 .1.3.6.1.4.1.14179.2.8.2.11 |
bsnTotalResponsesRetransmittedTotal Responses Retransmittedro Counter32 .1.3.6.1.4.1.14179.2.8.2.12 |
bsnTotalHandoffEndRequestsReceivedTotal Handoff End Requests Receivedro Counter32 .1.3.6.1.4.1.14179.2.8.2.13 |
bsnTotalStateTransitionsDisallowedTotal State Transitions Disallowedro Counter32 .1.3.6.1.4.1.14179.2.8.2.14 |
bsnTotalResourceErrorsTotal Resource Errorsro Counter32 .1.3.6.1.4.1.14179.2.8.2.15 |
bsnTotalHandoffRequestsSentTotal Handoff Requests Sentro Counter32 .1.3.6.1.4.1.14179.2.8.2.16 |
bsnTotalHandoffRepliesReceivedTotal Handoff Replies Receivedro Counter32 .1.3.6.1.4.1.14179.2.8.2.17 |
bsnTotalHandoffAsLocalReceivedTotal Handoffs As Local Receivedro Counter32 .1.3.6.1.4.1.14179.2.8.2.18 |
bsnTotalHandoffAsForeignReceivedTotal Handoffs As Foreign Receivedro Counter32 .1.3.6.1.4.1.14179.2.8.2.19 |
bsnTotalHandoffDeniesReceivedTotal Handoff Denies Receivedro Counter32 .1.3.6.1.4.1.14179.2.8.2.20 |
bsnTotalAnchorRequestsSentTotal Anchor Requests Sentro Counter32 .1.3.6.1.4.1.14179.2.8.2.21 |
bsnTotalAnchorDenyReceivedTotal Anchor Deny Receivedro Counter32 .1.3.6.1.4.1.14179.2.8.2.22 |
bsnTotalAnchorGrantReceivedTotal Anchor Grant Receivedro Counter32 .1.3.6.1.4.1.14179.2.8.2.23 |
bsnTotalAnchorTransferReceivedTotal Anchor Transfer Receivedro Counter32 .1.3.6.1.4.1.14179.2.8.2.24 |
bsnTotalHandoffRequestsIgnoredTotal Handoff Requests Ignoredro Counter32 .1.3.6.1.4.1.14179.2.8.2.25 |
bsnTotalPingPongHandoffRequestsDroppedTotal Ping Pong Handoff Requests Droppedro Counter32 .1.3.6.1.4.1.14179.2.8.2.26 |
bsnTotalHandoffRequestsDroppedTotal Handoff Requests Droppedro Counter32 .1.3.6.1.4.1.14179.2.8.2.27 |
bsnTotalHandoffRequestsDeniedTotal Handoff Requests Deniedro Counter32 .1.3.6.1.4.1.14179.2.8.2.28 |
bsnTotalClientHandoffAsLocalTotal Client Handoffs As Localro Counter32 .1.3.6.1.4.1.14179.2.8.2.29 |
bsnTotalClientHandoffAsForeignTotal Client Handoffs As Foreignro Counter32 .1.3.6.1.4.1.14179.2.8.2.30 |
bsnTotalAnchorRequestsReceivedTotal Anchor Requests Receivedro Counter32 .1.3.6.1.4.1.14179.2.8.2.31 |
bsnTotalAnchorRequestsDeniedTotal Anchor Requests Deniedro Counter32 .1.3.6.1.4.1.14179.2.8.2.32 |
bsnTotalAnchorRequestsGrantedTotal Anchor Requests Grantedro Counter32 .1.3.6.1.4.1.14179.2.8.2.33 |
bsnTotalAnchorTransferredTotal Anchor Transferredro Counter32 .1.3.6.1.4.1.14179.2.8.2.34 |
bsnTotalHandoffRequestsReceivedTotal Handoff Requests Receivedro Counter32 .1.3.6.1.4.1.14179.2.8.2.35 |
bsnIpsec OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.9 |
bsnWrasIpsecCACertificatero OCTET STRING .1.3.6.1.4.1.14179.2.9.1 |
bsnWrasIpsecCACertificateUpdateNote this attribute is for updating the certificate If you try to read it, it will always be ***rw OCTET STRING .1.3.6.1.4.1.14179.2.9.2 |
bsnWrasIpsecCertTableA table of Certificates. SEQUENCE OF BsnWrasIpsecCertEntry .1.3.6.1.4.1.14179.2.9.3 |
bsnWrasIpsecCertEntryEach entry contains a specific certificate. BsnWrasIpsecCertEntry .1.3.6.1.4.1.14179.2.9.3.1 |
bsnWrasIpsecCertNameThe name assigned to this set of IKE Certificates.rw DisplayString .1.3.6.1.4.1.14179.2.9.3.1.1 |
bsnWrasIpsecCertificateUpdateIf you try to read this it will always be ***rw OCTET STRING .1.3.6.1.4.1.14179.2.9.3.1.2 |
bsnWrasIpsecCertificatero OCTET STRING .1.3.6.1.4.1.14179.2.9.3.1.3 |
bsnWrasIpsecCertPasswordrw OCTET STRING .1.3.6.1.4.1.14179.2.9.3.1.4 |
bsnWrasIpsecCertStatusA row status type for the IKE Cert Entry.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.9.3.1.24 |
bsnAPGroupsVlanConfig OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.10 |
bsnAPGroupsVlanFeatureWhen enabled, Site Specific WLAN feature is enforced.rw Enumeration .1.3.6.1.4.1.14179.2.10.1 |
bsnAPGroupsVlanTableWireless Sites Table. SEQUENCE OF BsnAPGroupsVlanEntry .1.3.6.1.4.1.14179.2.10.2 |
bsnAPGroupsVlanEntryAn entry in bsnAPGroupsVlanTable. BsnAPGroupsVlanEntry .1.3.6.1.4.1.14179.2.10.2.1 |
bsnAPGroupsVlanNameThe string is an unique identifier/name assigned to a site.rw OCTET STRING .1.3.6.1.4.1.14179.2.10.2.1.1 |
bsnAPGroupsVlanDescriptionDescription about the site.rw OCTET STRING .1.3.6.1.4.1.14179.2.10.2.1.2 |
bsnAPGroupsVlanRowStatusRow Status for creation/deletion of entries in bsnAPGroupsVlanTablerw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.10.2.1.20 |
bsnAPGroupsVlanMappingTableA table for the WLAN-interace-mappings allowed for each configured site. Each site can have a set of WLANs associated with it.deprecated SEQUENCE OF BsnAPGroupsVlanMappingEntry .1.3.6.1.4.1.14179.2.10.3 |
bsnAPGroupsVlanMappingEntryAn entry in bsnAPGroupsVlanMappingTable.deprecated BsnAPGroupsVlanMappingEntry .1.3.6.1.4.1.14179.2.10.3.1 |
bsnAPGroupsVlanMappingSsidWhen an AP is associated with a site, and the site has an associated set of WLANs, then only those WLANs are beamed by the AP. Here 'bsnAPGroupsVlanMappingSsid' is the wlan to be used when a client connects on this AP.rwdeprecated DisplayString .1.3.6.1.4.1.14179.2.10.3.1.1 |
bsnAPGroupsVlanMappingInterfaceNameWhen an AP is associated with a site, and the site has an associated set of WLANs, then only those WLANs are beamed by the AP. Here 'bsnAPGroupsVlanMappingInterfaceName' is the interface to be used when a client connects to the 'bsnAPGroupsVlanMappingSsid' WLAN on this AP.rwdeprecated OCTET STRING .1.3.6.1.4.1.14179.2.10.3.1.2 |
bsnAPGroupsVlanMappingRowStatusRow Status for creation/deletion of WLAN-interface-mappings asscoiated with sites.rwdeprecated RowStatus (SNMPv2-TC) .1.3.6.1.4.1.14179.2.10.3.1.20 |
bsnWrasGroups OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.50 |
bsnEssGroupThis collection of objects provides information about Airespace Wireless LAN Configuration Attributes These objects are defined under bsnEss object.deprecated Unknown .1.3.6.1.4.1.14179.2.50.1 |
bsnApGroupThis collection of objects provide the information about Airespace APs that are associated with the Switch. These objects are defined under bsnAP object.deprecated Unknown .1.3.6.1.4.1.14179.2.50.2 |
bsnGlobalDot11GroupThis collection of objects provide the information about Airespace 802.11 standard attributes applied globally. These objects are defined under bsnGlobalDot11 object.deprecated Unknown .1.3.6.1.4.1.14179.2.50.3 |
bsnRrmGroupThis collection of objects provide the information about Airespace Radio Resource Management Configuration Parameters. These objects are defined under bsnRrm object. Unknown .1.3.6.1.4.1.14179.2.50.4 |
bsnAAAGroupThis collection of objects provide the information about Airespace Authentication, Authorization, and Accounting Attributes. These objects are defined under bsnAAA object.deprecated Unknown .1.3.6.1.4.1.14179.2.50.5 |
bsnTrapsGroupThis collection of objects provide the information about Airespace Trap Configuration and Trap definition. These objects are defined under bsnTrap.deprecated Unknown .1.3.6.1.4.1.14179.2.50.6 |
bsnUtilityGroupThis collection of objects provide the information about Airespace General Utilities such as ping, syslog. These objects are defined under bsnUtility.deprecated Unknown .1.3.6.1.4.1.14179.2.50.7 |
bsnMobilityGroupThis collection of objects provide the information about Airespace Mobility Group Parameters and ststistics. These are objects defined under bsnMobility. Unknown .1.3.6.1.4.1.14179.2.50.8 |
bsnIpsecGroupThis collection of objects provide the information about Airespace Global IpSec Group. These objects are defined under bsnIpsec. Unknown .1.3.6.1.4.1.14179.2.50.9 |
bsnWrasDepGroupThis collection of objects are derprecated in bsnWireless module.deprecated Unknown .1.3.6.1.4.1.14179.2.50.10 |
bsnWrasObsGroupThis collection of objects are obsoleted in bsnWireless module.obsolete Unknown .1.3.6.1.4.1.14179.2.50.11 |
bsnWrasTrapThis collection of objects provides all notification that Switch need to generate to the Management System.obsolete Unknown .1.3.6.1.4.1.14179.2.50.12 |
bsnEssGroupRev1This collection of objects provides information about Airespace Wireless LAN Configuration Attributes These objects are defined under bsnEss object. Unknown .1.3.6.1.4.1.14179.2.50.13 |
bsnGlobalDot11GroupRev1This collection of objects provide the information about Airespace 802.11 standard attributes applied globally. These objects are defined under bsnGlobalDot11 object. Unknown .1.3.6.1.4.1.14179.2.50.14 |
bsnAAAGroupRev1This collection of objects provide the information about Airespace Authentication, Authorization, and Accounting Attributes. These objects are defined under bsnAAA object. Unknown .1.3.6.1.4.1.14179.2.50.15 |
bsnTrapsGroupRev1This collection of objects provide the information about Airespace Trap Configuration and Trap definition. These objects are defined under bsnTrap. Unknown .1.3.6.1.4.1.14179.2.50.16 |
bsnWrasTrapRev1This collection of objects provides all notification that Switch need to generate to the Management System. Unknown .1.3.6.1.4.1.14179.2.50.17 |
bsnApGroupRev1This collection of objects provide the information about Airespace APs that are associated with the Switch. These objects are defined under bsnAP object. Unknown .1.3.6.1.4.1.14179.2.50.18 |
bsnUtilityGroupRev1This collection of objects provide the information about Airespace General Utilities such as ping, syslog. These objects are defined under bsnUtility. Unknown .1.3.6.1.4.1.14179.2.50.19 |
bsnWrasObsGroupRev1This collection of objects are obsoleted in bsnWireless module.obsolete Unknown .1.3.6.1.4.1.14179.2.50.20 |
bsnWrasObsTrapThis collection of objects provides all notification that Switch need to generate to the Management System.obsolete Unknown .1.3.6.1.4.1.14179.2.50.21 |
bsnWrasCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.14179.2.51 |
bsnWrasComplianceThe compliance statement for the SNMP entities that implement the bsnWireless module.deprecated Unknown .1.3.6.1.4.1.14179.2.51.1 |
bsnWrasComplianceRev1The compliance statement for the SNMP entities that implement the bsnWireless module. Unknown .1.3.6.1.4.1.14179.2.51.2 |