AH_TRAP_MIB
AI MIB Summary
The AH_TRAP_MIB facilitates the monitoring of authentication method states and security events for HiveAP wireless access points via SNMP traps. It specifically tracks authentication protocol transitions and method support status to enable real-time detection of access control anomalies on the network edge.
Authentication method supported by the HiveAP
Main OID:
IMPORTS.1.3.6.1.4.1.26928.1.1.1.1.1
83
Objects
Active
Status
3
Dependencies
Imported Objects
Objects
83 total| Object Name |
|---|
IMPORTSAuthentication method supported by the HiveAP MODULE-IDENTITY .1.3.6.1.4.1.26928.1.1.1.1.1 |
ahFailureTrapThis event is generated for any equipment or software failures. NOTIFICATION-TYPE .1.3.6.1.4.1.26928.1.1.1.1.1.1 |
ahThresholdCrossingEventThis event is generated whenever a threshold is crossed for the first time. NOTIFICATION-TYPE .1.3.6.1.4.1.26928.1.1.1.1.1.2 |
ahStateChangeEventThis event is generated whenever an object state change occurs. NOTIFICATION-TYPE .1.3.6.1.4.1.26928.1.1.1.1.1.3 |
ahConnectionChangeEventThis event is generated whenever a connection state change
occurs. The connection might be between a HiveAP and its client,
or between a HiveAP and a neighboring HiveAP. NOTIFICATION-TYPE .1.3.6.1.4.1.26928.1.1.1.1.1.4 |
ahIDPStationEventThis event is generated whenever IDP detects an AP
in its neighborhood. The ahRomoteId indicates the detected AP
MAC address, and the ahIDPCompliance indicates conformance of
IDP policy this AP satisfies. The ahIDPChannel and ahIDPRSSI
indicates the radio channel and Receive Signal Strenth Indication. NOTIFICATION-TYPE .1.3.6.1.4.1.26928.1.1.1.1.1.5 |
ahClientInfoEventThis event is generated whenever HiveAP a new client
makes an association and its IP address, hostname, and
User name is obtained. NOTIFICATION-TYPE .1.3.6.1.4.1.26928.1.1.1.1.1.6 |
ahPoEEventThis event is generated whenever a HiveAP (802.11n
product line) boots up or changes power levels. NOTIFICATION-TYPE .1.3.6.1.4.1.26928.1.1.1.1.1.7 |
ahChannelPowerChangeEventThis event is generated whenever a HiveAP boots up,
or changes channels or power levels. NOTIFICATION-TYPE .1.3.6.1.4.1.26928.1.1.1.1.1.8 |
ahIDPMitigateEventThis event is generated whenever IDP detects an rogue client
connect to a rogue AP. The ahRomoteId indicates the detected
Station MAC address. NOTIFICATION-TYPE .1.3.6.1.4.1.26928.1.1.1.1.1.9 |
ahInterferenceMapAlertEventFor every one minute interval, AP will monitor the interference channel utilizations
(snapshot, short term means average and running average) and CRC error rate
against their thresholds, if any one of them is above their threshold
(thresholds are settable by CLI), AP should send HM an interference alert event to HM.
AP will send out clear alert to HM only when: the last short term period��s CRC_error_rate,
means average Interference CU and the last snapshot interference CU are all below their thresholds. NOTIFICATION-TYPE .1.3.6.1.4.1.26928.1.1.1.1.1.10 |
ahBandwidthSentinelEventHiveOS will send two different kinds of traps: bandwidth sentinel alert trap, and bandwidth sentinel clear trap.
The ��alert�� trap will serve the purpose to tell HM that the client is violating the bandwidth sentinel,
the ��clear�� trap will clear the previous ��alert�� trap. NOTIFICATION-TYPE .1.3.6.1.4.1.26928.1.1.1.1.1.11 |
ahAlarmMsgMapAlertEventHiveOS will send two different kinds of level alert: interface level alert, and client level alert.
There are four alert types, CRC error rate, TX drop/retry rate, Rx drop rate; interface level includes all alert type,
the client level includes Tx drop/retry rate, Rx drop Rate; the 'set' alert means there is an alert raised,
with type indicated in the alert type field, the 'clear' alert means the previous alert condition has been cleared. NOTIFICATION-TYPE .1.3.6.1.4.1.26928.1.1.1.1.1.12 |
ahNotificationVarBind OBJECT IDENTIFIER .1.3.6.1.4.1.26928.1.1.1.1.2 |
ahAPIdIt is the node ID (MAC address in hexadecimal format)
of the HiveAP where the trap is generated. If a HiveAP is
configured with 2 hives, the node ID is the first MAC address
of the management interface. AhNodeID (AH-SMI-MIB) .1.3.6.1.4.1.26928.1.1.1.1.2.1 |
ahAPNameThe host name of the HiveAP where the trap is generated. AhString (AH-SMI-MIB) .1.3.6.1.4.1.26928.1.1.1.1.2.2 |
ahSeverityIt contains the serverity of the trap. Enumeration .1.3.6.1.4.1.26928.1.1.1.1.2.3 |
ahObjectNameIt describes the object for which the trap is generated. DisplayString (SIZE .1.3.6.1.4.1.26928.1.1.1.1.2.4 |
ahProbableCauseIt describes the probable cause of a problem. AhProbableCause .1.3.6.1.4.1.26928.1.1.1.1.2.5 |
ahCurValueIt contains the current value of a threshold counter. INTEGER .1.3.6.1.4.1.26928.1.1.1.1.2.6 |
ahThresholdHighIt contains the value for a high threshold. INTEGER .1.3.6.1.4.1.26928.1.1.1.1.2.7 |
ahThresholdLowIt contains the value for a low threshold. INTEGER .1.3.6.1.4.1.26928.1.1.1.1.2.8 |
ahPreviousStateIt contains the value for a previous state. AhState .1.3.6.1.4.1.26928.1.1.1.1.2.9 |
ahCurrentStateIt contains the value for the current state. AhState .1.3.6.1.4.1.26928.1.1.1.1.2.10 |
ahTrapDescIt contains the description of the trap. DisplayString (SNMPv2-TC) .1.3.6.1.4.1.26928.1.1.1.1.2.11 |
ahCodeIt contains access information to the Aerohive
logging/action dictionary. Integer32 .1.3.6.1.4.1.26928.1.1.1.1.2.12 |
ahIfIndexThe interface index used to identify uniquely
an interface (logical or physical). Integer32 .1.3.6.1.4.1.26928.1.1.1.1.2.13 |
ahObjectTypeIt specifies the object type: a client link or a neighbor link. Enumeration .1.3.6.1.4.1.26928.1.1.1.1.2.14 |
ahRemoteIdIt is the MAC address of the remote node. If the remote
node is a HiveAP, the ID must be the MAC address
of its management interface. If the remote node is a
client station, it must be the MAC address of the client. AhNodeID (AH-SMI-MIB) .1.3.6.1.4.1.26928.1.1.1.1.2.15 |
ahIDPTypeIt is used to indicate the AP identified is a
rogue, or valid, or compliant, or noncompliant, or external AP. Enumeration .1.3.6.1.4.1.26928.1.1.1.1.2.16 |
ahIDPChannelIt is the channel number used by the identified AP. Integer32 .1.3.6.1.4.1.26928.1.1.1.1.2.17 |
ahIDPRSSIIt is the RSSI for the identified AP or Client. Integer32 .1.3.6.1.4.1.26928.1.1.1.1.2.18 |
ahIDPComplianceIt is bit mask to indicate which policy the indentified
AP is compliant with (bit is set if it is NOT compliant). Enumeration .1.3.6.1.4.1.26928.1.1.1.1.2.19 |
ahSSIDIt contains the SSID name for the detected AP. DisplayString (SIZE .1.3.6.1.4.1.26928.1.1.1.1.2.20 |
ahStationTypeIt indicates whether it is event for a peer AP
or client PC Enumeration .1.3.6.1.4.1.26928.1.1.1.1.2.21 |
ahIDPStationDataIt is bit mask to indicate policies are detected for
the identified AP . Note: the oui_policy and ssid_policy are
omitted due to the presence of the ahRemoteID, and SSID in the
trap message. Enumeration .1.3.6.1.4.1.26928.1.1.1.1.2.22 |
ahRemovedIt indicates whether the AP or client can not
be detected. Enumeration .1.3.6.1.4.1.26928.1.1.1.1.2.23 |
ahClientMACIt contains the MAC address of the wireless client. It is
required. AhNodeID (AH-SMI-MIB) .1.3.6.1.4.1.26928.1.1.1.1.2.24 |
ahCLientIPIt contains the IP address of the wireless client. It is
optional. DisplayString (SNMPv2-TC) .1.3.6.1.4.1.26928.1.1.1.1.2.25 |
ahClientHostNameIt contains the host name of the wireless client. It is
optional. DisplayString (SNMPv2-TC) .1.3.6.1.4.1.26928.1.1.1.1.2.26 |
ahClientUserNameIt contains the user name of the wireless client. It is
optional. DisplayString (SNMPv2-TC) .1.3.6.1.4.1.26928.1.1.1.1.2.27 |
ahPowerSrcIt indicates whether the power source is from the power adaptor or PoE.
If the power source is the adaptor, PoE information in the trap is ignored. Enumeration .1.3.6.1.4.1.26928.1.1.1.1.2.28 |
ahPoEEth0OnIt indicates whether PoE is on eth0 or not. TruthValue (SNMPv2-TC) .1.3.6.1.4.1.26928.1.1.1.1.2.29 |
ahPoEEth0PwrIt indicates the power level of PoE in watts
multiply by 10. INTEGER .1.3.6.1.4.1.26928.1.1.1.1.2.30 |
ahPoEEth1OnIt indicates whether PoE is on eth1 or not. TruthValue (SNMPv2-TC) .1.3.6.1.4.1.26928.1.1.1.1.2.31 |
ahPoEEth1PwrIt indicates the power level of PoE on eht1 in watts
multiply by 10. INTEGER .1.3.6.1.4.1.26928.1.1.1.1.2.32 |
ahRadioChannelIt is the channel number currently in use for this radio.ro Integer32 .1.3.6.1.4.1.26928.1.1.1.1.2.33 |
ahRadioTxPowerIt is the transmit power in dBm that the radio is currently using. The range
is 0 to 20 dBm.ro Integer32 .1.3.6.1.4.1.26928.1.1.1.1.2.34 |
ahClientAuthMethodIt is the authentication method the client uses when
communicating with the HiveAP.ro AhAuthenticationMethod .1.3.6.1.4.1.26928.1.1.1.1.2.35 |
ahClientEncryptionMethodIt is the encryption method the client uses when communicating
with the HiveAP.ro AhEncrytionMethod .1.3.6.1.4.1.26928.1.1.1.1.2.36 |
ahClientMACProtocolIt is the radio mode the client uses when communicating
with the HiveAP.ro AhMACProtocol (AH-SMI-MIB) .1.3.6.1.4.1.26928.1.1.1.1.2.37 |
ahClientVLANIt is the VLAN that the client uses when communicating
with the HiveAP.ro Integer32 .1.3.6.1.4.1.26928.1.1.1.1.2.38 |
ahClientUserProfIdIt is the user profile ID that the client uses when communicating
with the HiveAP.ro Integer32 .1.3.6.1.4.1.26928.1.1.1.1.2.39 |
ahClientChannelIt is the radio channel that the client uses when communicating
with the HiveAP.ro Integer32 .1.3.6.1.4.1.26928.1.1.1.1.2.40 |
ahClientCWPUsedIt is the Boolean datatype indicating whether a captive web portal
is used.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.26928.1.1.1.1.2.41 |
ahBSSIDIt is the basic service set identifier of the client
if the ahRemoteId is a client.ro AhNodeID (AH-SMI-MIB) .1.3.6.1.4.1.26928.1.1.1.1.2.42 |
ahPoEEth0MaxSpeedIt is the automatically adjusted maximum Ethernet speed
based on the power source and level.ro Enumeration .1.3.6.1.4.1.26928.1.1.1.1.2.43 |
ahPoEEth1MaxSpeedIt is the automatically adjusted maximum Ethernet speed
based on the power source and level.ro Enumeration .1.3.6.1.4.1.26928.1.1.1.1.2.44 |
ahPoEWifi0SettingIt is the automatically adjusted Wi-Fi setting based on the
power source and power level.ro Enumeration .1.3.6.1.4.1.26928.1.1.1.1.2.45 |
ahPoEWifi1SettingIt is the automatically adjusted Wi-Fi setting based on the
power source and power level.ro Enumeration .1.3.6.1.4.1.26928.1.1.1.1.2.46 |
ahPoEWifi2SettingIt is the automatically adjusted Wi-Fi setting based on the
power source and power level.ro Enumeration .1.3.6.1.4.1.26928.1.1.1.1.2.47 |
ahAssociationTimeThe association time(s) of client connect or disconnect to AP.ro Counter32 .1.3.6.1.4.1.26928.1.1.1.1.2.48 |
ahIDPInNetIt is the Boolean datatype indicating whether AP is in local network.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.26928.1.1.1.1.2.49 |
ahDiscoverAgeIt is the age from the rogue client is discovered.ro Counter32 .1.3.6.1.4.1.26928.1.1.1.1.2.50 |
ahUpdateAgeIt is the age from the rogue client is updated.ro Counter32 .1.3.6.1.4.1.26928.1.1.1.1.2.51 |
ahRunningAverageInterferencechannel utilizations running average interference.ro INTEGER .1.3.6.1.4.1.26928.1.1.1.1.2.52 |
ahShortTermInterferencechannel utilizations short term interference.
The short term period is defined by CLI config,
usually, it should be in the range of 5 minutes to 30 minutes.ro INTEGER .1.3.6.1.4.1.26928.1.1.1.1.2.53 |
ahSnapshotInterferencechannel utilizations snapshot interference. it is the last minute��s means average.ro INTEGER .1.3.6.1.4.1.26928.1.1.1.1.2.54 |
ahFailureSetIt is the Boolean datatype indicating whether this failure(alert) is on or off.ro TruthValue (SNMPv2-TC) .1.3.6.1.4.1.26928.1.1.1.1.2.55 |
ahInterferenceThresholdthe configured channel utilizations interference threshold.
it is defined by CLI config.ro INTEGER .1.3.6.1.4.1.26928.1.1.1.1.2.56 |
ahCRCErrRateThresholdthe configured CRC error rate threshold. it is defined by CLI config.ro INTEGER .1.3.6.1.4.1.26928.1.1.1.1.2.57 |
ahCRCErrRateshort term CRC error rate. The interval of the refresh of CRC error rate calculation
is the same interval as channel utilization short term means average interval.ro INTEGER .1.3.6.1.4.1.26928.1.1.1.1.2.58 |
ahBandwidthSentinelStatusBandwidth sentinel status.
In alert message, the value should be zero. In clear message, the value should be 1.ro Enumeration .1.3.6.1.4.1.26928.1.1.1.1.2.59 |
ahGuaranteedBandwidththe configured guaranteed bandwidth(Kbps). it is defined by CLI config.ro INTEGER .1.3.6.1.4.1.26928.1.1.1.1.2.60 |
ahActualBandwidththe actual bandwidth(Kbps).ro INTEGER .1.3.6.1.4.1.26928.1.1.1.1.2.61 |
ahBandwidthSentinelActionbit maps to indicate which action has been taken on this client.
bit 0: indicate whether log the guaranteed bandwidth violation or not,
bit 1: indicate whether add more token to meet the minimum guaranteed bandwidth or not.ro Counter32 .1.3.6.1.4.1.26928.1.1.1.1.2.62 |
ahBeaconIntervalIt is the number of time units between Beacon transmissions, One time unit is
1024 microseconds.ro Counter32 .1.3.6.1.4.1.26928.1.1.1.1.2.63 |
ahLevelThe level value will tell HM whether this is an interface level alert or a client alert.ro Enumeration .1.3.6.1.4.1.26928.1.1.1.1.2.64 |
ahAlarmAlertTypeThere are five types, CRC Rate only applies to interface level alert,
TX drop/retry rate is is calculated based on retries over total unicast TX frames,
RX drop rate is calculated based on the dropped RX frames over total RX frames,
Airtime percentage is the sum of both TX and RX airtime percentages.ro Enumeration .1.3.6.1.4.1.26928.1.1.1.1.2.65 |
ahThresholdValuethe configured CRC error rate, TX drop/retry rate, RX drop rate threshold. it is defined by CLI config.ro INTEGER .1.3.6.1.4.1.26928.1.1.1.1.2.66 |
ahShortTermValuethe percentage of this sampling period, CRC error rate, TX drop/retry rate, RX drop rate.ro INTEGER .1.3.6.1.4.1.26928.1.1.1.1.2.67 |
ahSnapshotValuethe snapshot value of CRC error rate, TX drop/retry rate, RX drop rate.ro INTEGER .1.3.6.1.4.1.26928.1.1.1.1.2.68 |
ahIfNameName - uniquely identifies an AP Interface.ro AhString (AH-SMI-MIB) .1.3.6.1.4.1.26928.1.1.1.1.2.69 |