A3Com-Sdlc-r1-MIB
AI MIB Summary
Standard SNMP MIB module defining data structures for A3Com-Sdlc-r1-MIB.
118
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
118 total| Object Name |
|---|
a3com OBJECT IDENTIFIER .1.3.6.1.4.1.43 |
RFC1213-MIB Unknown .1.3.6.1.4.1.43 |
brouterMIB OBJECT IDENTIFIER .1.3.6.1.4.1.43.2 |
sdlc OBJECT IDENTIFIER .1.3.6.1.4.1.43.2.25 |
sdlcPortStatusChangeThis trap indicates that the state of an SDLC
port has transitioned to active or inactive. TRAP-TYPE .1.3.6.1.4.1.43.2.25.0.1 |
sdlcLSStatusChangeThis trap indicates that the state of an SDLC
link station has transitioned to contacted or
discontacted. TRAP-TYPE .1.3.6.1.4.1.43.2.25.0.2 |
sdlcPortGroup OBJECT IDENTIFIER .1.3.6.1.4.1.43.2.25.1 |
sdlcPortAdminTableThis table contains objects that can be
changed to manage an SDLC port. Changing one
of these parameters may take effect in the
operating port immediately or may wait until
the interface is restarted depending on the
details of the implementation.
Most of the objects in this read-write table
have corresponding read-only objects in the
sdlcPortOperTable that return the current
operating value.
The operating values may be different from
these configured values if a configured
parameter was changed after the interface was
started. SEQUENCE OF SdlcPortAdminEntry .1.3.6.1.4.1.43.2.25.1.1 |
sdlcPortAdminEntryA list of configured values for an SDLC port. SdlcPortAdminEntry .1.3.6.1.4.1.43.2.25.1.1.1 |
sdlcPortAdminNameAn octet string that defines the physical port
to which this interface is assigned. It has
implementation-specific significance. Its value
shall be unique within the administered
system. It must contain only ASCII printable
characters. Should an implementation choose to
accept a write operation for this object, it
causes the logical port definition associated
with the table instance to be moved to a
different physical port. A write operation
shall not take effect until the port is cycled
inactive.ro DisplayString .1.3.6.1.4.1.43.2.25.1.1.1.1 |
sdlcPortAdminRoleThis object describes the role that the link
station shall assume the next time a connection
is established.
Even though this is defined as a port object,
it is a link station attribute in the sense
that a role is per link station. However, it
is not possible to vary link station roles on a
particular port. For example, if an SDLC port
is configured to primary, all link stations on
that port must be primary.rw Enumeration .1.3.6.1.4.1.43.2.25.1.1.1.2 |
sdlcPortAdminTypeThis parameter defines whether the SDLC port
is to connect to a leased or switched line. A
write operation to this administrative value
shall not take effect until the SDLC port has
been cycled inactive.rw Enumeration .1.3.6.1.4.1.43.2.25.1.1.1.3 |
sdlcPortAdminTopologyThis parameter defines whether the SDLC port is
capable of operating in either a point-to-point
or multipoint topology.
sdlcPortAdminTopology == multipoint implies the
port can also operate in a point-to-point
topology. sdlcPortAdminTopology ==
pointToPoint does not imply the port can
operate in a multipoint topology.
A write operation to this administrative value
shall not take effect until the SDLC port has
been cycled inactive.rw Enumeration .1.3.6.1.4.1.43.2.25.1.1.1.4 |
sdlcPortAdminACTIVTOThis parameter defines the period of time (in
1/100ths of a second) that the port will allow a
switched line to remain inactive before
disconnecting. A switched line is considered
to be inactive if there are no I-Frames being
transferred. A value of zero indicates no
timeout. Depending on the implementation, a
write operation to this administered value may
not take effect until the port is cycled
inactive.
This object only has meaning for SDLC ports
where sdlcPortAdminType == switched
The object descriptor contains the name of an
NCP configuration parameter, ACTIVTO. Please
note that the value of this object represents
1/100ths of a second while the NCP ACTIVTO is
represented in seconds.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.43.2.25.1.1.1.5 |
sdlcPortAdminPAUSEThis object defines the minimum elapsed time
(in 1/100ths of a second) between any two
traversals of the poll list for a primary SDLC
port. Depending on the implementation, a write
operation to this administered value may not
take effect until the port is cycled inactive.
The object descriptor contains the name of an
NCP configuration parameter, PAUSE. Please
note that the value of this object represents
1/100ths of a second while the NCP PAUSE is
represented in 1/10ths of a second.
This object only has meaning for SDLC ports
where sdlcPortAdminRole == primaryrw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.43.2.25.1.1.1.6 |
sdlcPortAdminSlowPollTimerThis object describes the elapsed time (in
1/100ths of a second) between polls for failed
secondary link station addresses. Depending
on the implementation, a write operation to
this administered value may not take effect
until the port is cycled inactive.
This object only has meaning for SDLC ports
where
sdlcPortAdminRole == primary
and
sdlcPortAdminTopology == multipointrw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.43.2.25.1.1.1.7 |
sdlcPortOperTableThis table contains current SDLC port
parameters. Many of these objects have
corresponding objects in the sdlcPortAdminTable. SEQUENCE OF SdlcPortOperEntry .1.3.6.1.4.1.43.2.25.1.2 |
sdlcPortOperEntryCurrently set parameters for a specific SDLC
port. SdlcPortOperEntry .1.3.6.1.4.1.43.2.25.1.2.1 |
sdlcPortOperNameAn octet string that describes the physical
port to which this interface is currently
attached. It has implementation-specific
significance.ro DisplayString .1.3.6.1.4.1.43.2.25.1.2.1.1 |
sdlcPortOperRoleThis object describes the role that the link
station has assumed on this connection.
Even though this is defined as a port object,
it is a link station attribute in the sense
that a role is per link station. However, it
is not possible to vary link station roles on a
particular port. For example, if an SDLC port
is configured to primary, all link stations on
that port must be primary.
The value of sdlcPortOperRole is undefined(3)
whenever the link station role has not yet been
established by the mode setting command.ro Enumeration .1.3.6.1.4.1.43.2.25.1.2.1.2 |
sdlcPortOperTypeThis parameter defines whether the SDLC port
is currently operating as though connected to a
leased or switched line.ro Enumeration .1.3.6.1.4.1.43.2.25.1.2.1.3 |
sdlcPortOperTopologyThis parameter defines whether the SDLC port is
mandatoryly operating in a point-to-point or
multipoint topology.ro Enumeration .1.3.6.1.4.1.43.2.25.1.2.1.4 |
sdlcPortOperACTIVTOThis parameter defines the period of time (in
100ths of a second) that the port will allow a
switched line to remain inactive before
disconnecting. A switched line is considered
to be inactive if there are no I-Frames being
transferred.
The object descriptor contains the name of an
NCP configuration parameter, ACTIVTO. Please
note that the value of this object represents
1/100ths of a second while the NCP ACTIVTO is
represented in seconds.
A value of zero indicates no timeout.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.43.2.25.1.2.1.5 |
sdlcPortOperPAUSEThis object describes the current minimum
elapsed time (in 1/100ths of a second) between
any two traversals of the poll list for a
primary SDLC port.
The object descriptor contains the name of an
NCP configuration parameter, PAUSE. Please
note that the value of this object represents
1/100ths of a second while the NCP PAUSE is
represented in 1/10ths of a second.
This object only has meaning for SDLC ports
where
sdlcPortAdminRole == primaryro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.43.2.25.1.2.1.6 |
sdlcPortOperSlowPollMethodThis object defines the exact method that is in
effect for periodically polling failed secondary
link station addresses.
If sdlcPortOperSlowPollMethod == servlim, then
sdlcPortOperSERVLIM defines the actual polling
characteristics.
If sdlcPortOperSlowPollMethod == pollpause,
then sdlcPortOperSlowPollTimer defines the
actual polling characteristics.
If sdlcPortOperSlowPollMethod == other, then
the polling characteristics are modeled in
vendor-specific objects.
This object only has meaning for SDLC ports
where
sdlcPortOperRole == primary
and
sdlcPortOperTopology == multipointro Enumeration .1.3.6.1.4.1.43.2.25.1.2.1.7 |
sdlcPortOperSlowPollTimerThis object describes the elapsed time (in
1/100ths of a second) between polls for failed
secondary link station addresses.
This object only has meaning for SDLC ports
where
sdlcPortOperRole == primary
and
sdlcPortOperTopology == multipointro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.43.2.25.1.2.1.8 |
sdlcPortOperLastFailTimeThis object describes the value of sysUpTime
when this SDLC port last failed. If the port
has not failed, then this value shall be zero.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.43.2.25.1.2.1.9 |
sdlcPortOperLastFailCauseThis enumerated object describes the cause of
the last failure of this SDLC port. If the
port has not failed, then this object has a
value of undefined(1).ro Enumeration .1.3.6.1.4.1.43.2.25.1.2.1.10 |
sdlcPortStatsTableEach entry in this table contains statistics
for a specific SDLC port. SEQUENCE OF SdlcPortStatsEntry .1.3.6.1.4.1.43.2.25.1.3 |
sdlcPortStatsEntryA list of statistics for an SDLC port. SdlcPortStatsEntry .1.3.6.1.4.1.43.2.25.1.3.1 |
sdlcPortStatsPhysicalFailuresThis object reflects the total number of times
this port has failed due to its physical media
since port startup. At port startup time,
this object must be initialized to zero.ro Counter .1.3.6.1.4.1.43.2.25.1.3.1.1 |
sdlcPortStatsInvalidAddressesThis object reflects the total number of
frames received by this port with invalid link
station addresses.ro Counter .1.3.6.1.4.1.43.2.25.1.3.1.2 |
sdlcPortStatsDwarfFramesThis object reflects the total number of
frames received by this port which were
delivered intact by the physical layer but were
too short to be legal.
Ignoring the frame check sequence (FCS), a
frame is considered to be too short if it
is less than 2 bytes for sdlcLSOperMODULO of
eight, or if it is less than 3 bytes for
sdlcLSOperMODULO of onetwentyeight.ro Counter .1.3.6.1.4.1.43.2.25.1.3.1.3 |
sdlcLSGroup OBJECT IDENTIFIER .1.3.6.1.4.1.43.2.25.2 |
sdlcLSAdminTableThis table contains objects that can be
changed to manage an SDLC link station.
Changing one of these parameters may take
effect in the operating link immediately or may
wait until the link is restarted depending on
the details of the implementation.
Most of the objects in this read-write table
have corresponding read-only objects in the
sdlcLSOperTable that reflect the current
operating value.
The operating values may be different from
these configured values if changed by XID
negotiation or if a configured parameter was
changed after the link was started. SEQUENCE OF SdlcLSAdminEntry .1.3.6.1.4.1.43.2.25.2.1 |
sdlcLSAdminEntryA list of configured values for an SDLC link
station. SdlcLSAdminEntry .1.3.6.1.4.1.43.2.25.2.1.1 |
sdlcLSAddressThis value is the poll address of the
secondary link station for this SDLC link. It
uniquely identifies the SDLC link station
within a single SDLC port.rw INTEGER .1.3.6.1.4.1.43.2.25.2.1.1.1 |
sdlcLSAdminNameAn octet string that defines the local name of
the SDLC link station. This field may be sent
in the XID3 control vector 0x0E, type 0xF7.rw DisplayString .1.3.6.1.4.1.43.2.25.2.1.1.2 |
sdlcLSAdminStateThis object controls the desired state of the
SDLC station. The managed system shall attempt
to keep the operational state, sdlcLSOperState,
consistent with this value.rw Enumeration .1.3.6.1.4.1.43.2.25.2.1.1.3 |
sdlcLSAdminMAXDATAThis object contains the maximum PDU size that
the local link station thinks it can send to
the adjacent link station before having
received any XID from the ALS. After the
maximum PDU size that the ALS can receive is
known (via XID exchange) that value is
reflected in sdlcLSOperMAXDATASend and takes
precedence over this object.
This value includes the Transmission Header
(TH) and the Request Header (RH).ro Integer32 .1.3.6.1.4.1.43.2.25.2.1.1.4 |
sdlcLSAdminREPLYTOThis object controls the reply timeout (in
1/100ths of a second) for an SDLC link
station. If the link station does not receive
a response to a poll or message before the
specified time expires then the appropriate
error recovery shall be initiated.
The object descriptor contains the name of an
NCP configuration parameter, REPLYTO. Please
note that the value of this object represents
1/100ths of a second while the NCP REPLYTO is
represented in 1/10ths of a second.
Depending on the implementation, a write
operation to this administered value may not
change the operational value, sdlcLSOperREPLYTO,
until the link station is cycled inactive.
This object only has meaning for SDLC ports
where sdlcPortAdminRole == primaryrw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.43.2.25.2.1.1.5 |
sdlcLSAdminMAXINThis object controls the maximum number of
unacknowledged I-frames which an SDLC link
station may receive. This should range from 1
to (sdlcLSAdminMODULO - 1). This value is sent
in the XID to the ALS.ro INTEGER .1.3.6.1.4.1.43.2.25.2.1.1.6 |
sdlcLSAdminMAXOUTThis object controls the maximum number of
consecutive unacknowledged I-frames which an
SDLC link station shall send without an
acknowledgement. This shall range from 1 to
(sdlcLSAdminMODULO - 1).
For link stations on switched SDLC lines,
certain implementations may choose to override
this administered value with the value
received in the XID exchange.
Depending on the implementation, a write
operation to this administered value may not
change the operational value, sdlcLSOperMAXOUT,
until the link station is cycled inactive.rw INTEGER .1.3.6.1.4.1.43.2.25.2.1.1.7 |
sdlcLSAdminMODULOThis object controls the modulus for an SDLC
link station. This modulus determines the size
of the rotating acknowledgement window used the
SDLC link station pair.
An implementation can support only modulo 8,
only modulo 128, or both.ro Enumeration .1.3.6.1.4.1.43.2.25.2.1.1.8 |
sdlcLSAdminRETRIESmThis object controls number of retries in a
retry sequence for the local SDLC link
station. A retry sequence is a series of
retransmitted frames ( data or control) for
which no positive acknowledgement is received.
The number of times that the retry sequence is
to be repeated is controlled by the object:
sdlcLSAdminRETRIESn. The interval between retry
sequences is controlled by the object:
sdlcLSAdminRETRIESt.
A value of zero indicates no retries. If the
value of sdlcLSAdminRETRIESm is zero, then the
values of sdlcLSAdminRETRIESt and
sdlcLSAdminRETRIESn should also be zero.ro INTEGER .1.3.6.1.4.1.43.2.25.2.1.1.9 |
sdlcLSAdminRETRIEStThis object controls the interval (in 1/100ths
of a second) between retry sequences for the
local SDLC link station if multiple retry
sequences are specified . A retry sequence is
a series of retransmitted frames ( data or
control) for which no positive acknowledgement
is received.
The number of repeated retries sequences is
controlled by the object: sdlcLSAdminRETRIESn.
The retries per sequence is controlled by the
object: sdlcLSAdminRETRIESm.
The object descriptor contains the name of an
NCP configuration parameter, RETRIESt. Please
note that the value of this object represents
1/100ths of a second while the NCP RETRIESt is
represented in seconds.
Depending on the implementation, a write
operation to this administered value may not
change the operational value, sdlcLSOperRETRIESt,
until the link station is cycled inactive.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.43.2.25.2.1.1.10 |
sdlcLSAdminRETRIESnThis object controls the number of times that
a retry sequence is repeated for the local SDLC
link station. A retry sequence is a series of
retransmitted frames ( data or control) for
which no positive acknowledgement is received.
The interval between retry sequences is
controlled by the object: sdlcLSAdminRETRIESt.
The retries per sequence is controlled by the
object: sdlcLSAdminRETRIESm.
Depending on the implementation, a write
operation to this administered value may not
change the operational value, sdlcLSOperRETRIESn,
until the link station is cycled inactive.rw Integer32 .1.3.6.1.4.1.43.2.25.2.1.1.11 |
sdlcLSAdminRNRLIMITThis object controls the length of time (in
1/100ths of a second) that an SDLC link station
will allow its adjacent link station to remain
in a busy (RNR) state before declaring it
inoperative.
A value of sdlcLSAdminRNRLIMIT == 0 means there
is no limit.
The object descriptor contains the name of an
NCP configuration parameter, RNRLIMIT. Please
note that the value of this object represents
1/100ths of a second while the NCP RNRLIMIT is
represented in minutes.
Depending on the implementation, a write
operation to this administered value may not
change the operational value, sdlcLSOperRNRLIMIT,
until the link station is cycled inactive.rw TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.43.2.25.2.1.1.12 |
sdlcLSAdminDATMODEThis object controls whether communications
mode with the adjacent link station is
two-way-alternate (half) or two-way-simultaneous
(full).ro Enumeration .1.3.6.1.4.1.43.2.25.2.1.1.13 |
sdlcLSAdminGPollThis object describes the group poll address
for this link station instance. If group poll
is not in effect for this link station
instance, the value for sdlcLSAdminGPoll should
be zero.
Depending on the implementation, a write
operation to this administered value may not
change the operational value, sdlcLSOperGPoll,
until the link station is cycled inactive.rw INTEGER .1.3.6.1.4.1.43.2.25.2.1.1.14 |
sdlcLSAdminSimRimThis object controls the support for
transmission and receipt of SIM and RIM control
frames for this link station. The value of
this object controls the setting of the
transmit-receive capability sent in the XID
field.ro Enumeration .1.3.6.1.4.1.43.2.25.2.1.1.15 |
sdlcLSOperTableThis table contains current SDLC link
parameters. Many of these objects have
corresponding objects in the
sdlcLSAdminTable. SEQUENCE OF SdlcLSOperEntry .1.3.6.1.4.1.43.2.25.2.2 |
sdlcLSOperEntryA list of status and control values for an
SDLC link station. SdlcLSOperEntry .1.3.6.1.4.1.43.2.25.2.2.1 |
sdlcLSOperNameAn octet string that defines the name of the
remote SDLC link station. This field is
received in the XID3 control vector 0x0E, type
0xF7.ro DisplayString .1.3.6.1.4.1.43.2.25.2.2.1.1 |
sdlcLSOperRoleThis object reflects the current role that the
link station is assuming.
The value of sdlcLSOperRole is undefined(3)
whenever the link station role has not yet been
established by the mode setting command.ro Enumeration .1.3.6.1.4.1.43.2.25.2.2.1.2 |
sdlcLSOperStateThis object describes the operational state of
the SDLC link station. The managed system
shall attempt to keep this value consistent
with the administered state, sdlcLSAdminStatero Enumeration .1.3.6.1.4.1.43.2.25.2.2.1.3 |
sdlcLSOperMAXDATAThis object contains the actual maximum PDU
size that the local link station can send to
the adjacent link station. This object is
established from the value received in the XID
from the adjacent link station. If no XID
is received, then this value is implementation
dependent (for instance, it could be the value
of sdlcLSAdminMAXDATA).
This value includes the Transmission Header
(TH) and the Request Header (RH).ro INTEGER .1.3.6.1.4.1.43.2.25.2.2.1.4 |
sdlcLSOperREPLYTOThis object reflects the current reply timeout
(in 1/100ths of a second) for an SDLC link
station. If the link station does not receive
a response to a poll or message before the
specified time expires then the appropriate
error recovery shall be initiated.
The object descriptor contains the name of an
NCP configuration parameter, REPLYTO. Please
note that the value of this object represents
1/100ths of a second while the NCP REPLYTO is
represented in 1/10ths of a second.
This object only has meaning for SDLC ports
where sdlcPortOperRole == primaryro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.43.2.25.2.2.1.5 |
sdlcLSOperMAXINThis object reflects the current maximum
number of unacknowledged I-frames which an SDLC
link station may receive. This shall range
from 1 to (sdlcLSOperMODULO - 1).ro INTEGER .1.3.6.1.4.1.43.2.25.2.2.1.6 |
sdlcLSOperMAXOUTThis object controls the maximum number of
consecutive unacknowledged I-frames which an
SDLC link station shall send without an
acknowledgement. This shall range from 1 to
(sdlcLSAdminMODULO - 1).
This value may controlled by the administered
MAXOUT, sdlcLSAdminMAXOUT, or by the MAXIN value
received during the XID exchange.ro INTEGER .1.3.6.1.4.1.43.2.25.2.2.1.7 |
sdlcLSOperMODULOThis object reflects the current modulus for
an SDLC link station. This modulus determines
the size of rotating acknowledgement window
used by the SDLC link station pair.ro Enumeration .1.3.6.1.4.1.43.2.25.2.2.1.8 |
sdlcLSOperRETRIESmThis object controls number of retries in a
retry sequence for an SDLC link station. A
retry sequence is a series of retransmitted
frames ( data or control) for which no positive
acknowledgement is received.
The current number of times that the retry
sequence is to be repeated is reflected by the
object: sdlcLSOperRETRIESn. The current
interval between retry sequences is reflected
by the object: sdlcLSOperRETRIESt.ro INTEGER .1.3.6.1.4.1.43.2.25.2.2.1.9 |
sdlcLSOperRETRIEStThis object reflects the current interval (in
1/100ths of a second) between retry sequences
for an SDLC link station if multiple retry
sequences are specified. A retry sequence is a
series of retransmitted frames ( data or
control) for which no positive acknowledgement
is received.
The object descriptor contains the name of an
NCP configuration parameter, RETRIESt. Please
note that the value of this object represents
1/100ths of a second while the NCP RETRIESt is
represented in seconds.
The current number of repeated retries
sequences is reflected by the object:
sdlcLSOperRETRIESn. The current retries per
sequence is reflected by the object:
sdlcLSOperRETRIESm.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.43.2.25.2.2.1.10 |
sdlcLSOperRETRIESnThis object reflects the current number of
times that a retry sequence is repeated for an
SDLC link station. A retry sequence is a
series of retransmitted frames ( data or
control) for which no positive acknowledgement
is received.
The current interval between retry sequences is
reflected by the object: sdlcLSOperRETRIESn.
The current retries per sequence is reflected
by the object: sdlcLSOperRETRIESm.ro INTEGER .1.3.6.1.4.1.43.2.25.2.2.1.11 |
sdlcLSOperRNRLIMITThis object reflects the current length of
time (in 1/100ths of a second) that an SDLC
link station will allow its adjacent link
station to remain in a busy (RNR) state before
declaring it inoperative.
The object descriptor contains the name of an
NCP configuration parameter, RNRLIMIT. Please
note that the value of this object represents
1/100ths of a second while the NCP RNRLIMIT is
represented in minutes.
A value of sdlcLSOperRNRLIMIT == 0 means there
is no limit.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.43.2.25.2.2.1.12 |
sdlcLSOperDATMODEThis object reflects whether the current
communications mode with the adjacent link
station is two-way-alternate (half) or
two-way-simultaneous (full).ro Enumeration .1.3.6.1.4.1.43.2.25.2.2.1.13 |
sdlcLSOperLastFailTimeThis object describes the value of sysUpTime
when this SDLC link station last failed. If
the link station has not failed, then this
value shall be zero.ro TimeTicks (SNMPv2-SMI) .1.3.6.1.4.1.43.2.25.2.2.1.14 |
sdlcLSOperLastFailCauseThis enumerated object reflects the cause of
the last failure of this SDLC link station. If
the link station has not failed, then this
object will have a value of undefined(1).ro Enumeration .1.3.6.1.4.1.43.2.25.2.2.1.15 |
sdlcLSOperLastFailCtrlInThis object reflects the last control octet or
octets (depending on modulus) received by this
SDLC link station at the time of the last
failure. If the link station has not failed,
then this value has no meaning.ro OCTET STRING .1.3.6.1.4.1.43.2.25.2.2.1.16 |
sdlcLSOperLastFailCtrlOutThis object reflects the last control octet or
octets (depending on modulus) sent by this SDLC
link station at the time of the last failure.
If the link station has not failed, then this
value has no meaning.ro OCTET STRING .1.3.6.1.4.1.43.2.25.2.2.1.17 |
sdlcLSOperLastFailFRMRInfoThis object reflects the information field of
the FRMR frame if the last failure for this
SDLC link station was as a result of an invalid
frame. Otherwise, this field has no meaning.ro OCTET STRING .1.3.6.1.4.1.43.2.25.2.2.1.18 |
sdlcLSOperLastFailREPLYTOsThis object reflects the number of times that
the REPLYTO timer had expired for an SDLC link
station at the time of the last failure. If the
link station has not failed, then this value
has no meaning.ro Counter .1.3.6.1.4.1.43.2.25.2.2.1.19 |
sdlcLSOperGPollThis object describes the group poll address
in effect for this link station instance.ro INTEGER .1.3.6.1.4.1.43.2.25.2.2.1.20 |
sdlcLSOperSimRimThis object reflects the support for
transmission and receipt of SIM and RIM control
frames for the adjacent link station. The
value of this object is set from the XID field
received from the adjacent link station.ro Enumeration .1.3.6.1.4.1.43.2.25.2.2.1.21 |
sdlcLSStatsTableEach entry in this table contains statistics
for a specific SDLC link station. SEQUENCE OF SdlcLSStatsEntry .1.3.6.1.4.1.43.2.25.2.3 |
sdlcLSStatsEntryA list of statistics for an SDLC link station. SdlcLSStatsEntry .1.3.6.1.4.1.43.2.25.2.3.1 |
sdlcLSStatsBLUsInThis object reflects the total basic link
units (BLUs; frames) received from an adjacent
SDLC link station since link station startup.
At link station startup time, this object must
be initialized to zero.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.1 |
sdlcLSStatsBLUsOutThis object reflects the total basic link
units (BLUs; frames), transmitted to an
adjacent SDLC link station since link station
startup. At link station startup time, this
object must be initialized to zero.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.2 |
sdlcLSStatsOctetsInThis object reflects the total octets received
from an adjacent SDLC link station since link
station startup. This object covers the
address, control, and information field of
I-Frames only. At link station startup time,
this object must be initialized to zero.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.3 |
sdlcLSStatsOctetsOutThis object reflects the total octets
transmitted to an adjacent SDLC link station
since link station startup. This object covers
the address, control, and information field of
I-Frames only. At link station startup time,
this object must be initialized to zero.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.4 |
sdlcLSStatsPollsOutThis object reflects the total polls sent to
an adjacent SDLC link station since link
station startup. At link station startup time,
this object must be initialized to zero.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.5 |
sdlcLSStatsPollRspsOutThis object reflects the total number of poll
responses sent to the adjacent SDLC link
station since link station startup. This value
includes I-frames that are sent in response to
a poll.
At link station startup time, this object must
be initialized to zero.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.6 |
sdlcLSStatsLocalBusiesThis object reflects the total number of times
that the local SDLC link station has entered a
busy state (RNR) since link station startup.
At link station startup time, this object must
be initialized to zero.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.7 |
sdlcLSStatsRemoteBusiesThis object reflects the total number of times
that an adjacent ( remote) SDLC link station
has entered a busy state (RNR) since link
station startup. At link station startup time,
this object must be initialized to zero.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.8 |
sdlcLSStatsIFramesInThis object reflects the total I-frames
received from an adjacent SDLC link station
since link station startup. At link station
startup time, this object must be initialized
to zero.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.9 |
sdlcLSStatsIFramesOutThis object reflects the total I-frames
transmitted to an adjacent SDLC link station
since link station startup. At link station
startup time, this object must be initialized
to zero.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.10 |
sdlcLSStatsRetransmitsThis object reflects the total number of
information frames retransmitted to a remote
link station because the N(r) received from
that link station indicated that one or more
information frames sent to that station were
lost. This event causes the first missing
information frame of a window and all
subsequent information frames to be
retransmitted. At link station startup time,
this object must be initialized to zero.
Management: If the value of
sdlcLSStatsRetransmits grows over time,
then the quality of the serial line is in
question. You might want to look at
decreasing the value for sdlcLSAdminMAXDATA
to compensate for the lower quality line.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.11 |
sdlcLSStatsIOctetsInThis object reflects the octets received
in I-frames from an adjacent SDLC link station
since link station startup. This object covers
valid, retried, and out-of-order I-Frames.
At link station startup time, this object must
be initialized to zero.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.12 |
sdlcLSStatsIOctetsOutThis object reflects the octets transmitted
in I-frames to an adjacent SDLC link station
since link station startup. This object covers
valid, retried, and out-of-order I-Frames.
At link station startup time, this object must
be initialized to zero.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.13 |
sdlcLSStatsUIFramesInThis object reflects the total UI-frames
received from an adjacent SDLC link station
since link station startup.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.14 |
sdlcLSStatsUIFramesOutThis object reflects the total UI-frames
transmitted to an adjacent SDLC link station
since link station startup.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.15 |
sdlcLSStatsXIDsInThis object reflects the total XID frames
received from an adjacent SDLC link station
since link station startup.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.16 |
sdlcLSStatsXIDsOutThis object reflects the total XID frames
transmitted to an adjacent SDLC link station
since link station startup.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.17 |
sdlcLSStatsTESTsInThis object reflects the total TEST frames,
commands or responses, received from an
adjacent SDLC link station since link station
startup.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.18 |
sdlcLSStatsTESTsOutThis object reflects the total TEST frames,
commands or responses, transmitted to an
adjacent SDLC link station since link station
startup.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.19 |
sdlcLSStatsREJsInThis object reflects the total REJ frames
received from an adjacent SDLC link station
since link station startup.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.20 |
sdlcLSStatsREJsOutThis object reflects the total REJ frames
transmitted to an adjacent SDLC link station
since link station startup.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.21 |
sdlcLSStatsFRMRsInThis object reflects the total frame reject
(FRMR) frames received from an adjacent SDLC
link station since link station startup.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.22 |
sdlcLSStatsFRMRsOutThis object reflects the total frame reject
(FRMR) frames transmitted to an adjacent SDLC
link station since link station startup.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.23 |
sdlcLSStatsSIMsInThis object reflects the total set
initialization mode (SIM) frames received from
an adjacent SDLC link station since link station
startup.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.24 |
sdlcLSStatsSIMsOutThis object reflects the total set
initialization mode (SIM) frames transmitted to
an adjacent SDLC link station since link station
startup. At link station startup time, this
object must be initialized to zero.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.25 |
sdlcLSStatsRIMsInThis object reflects the total request
initialization mode (RIM) frames received from
an adjacent SDLC link station since link station
startup. At link station startup time, this
object must be initialized to zero.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.26 |
sdlcLSStatsRIMsOutThis object reflects the total request
initialization mode (RIM) frames transmitted to
an adjacent SDLC link station since link station
startup. At link station startup time, this
object must be initialized to zero.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.27 |
sdlcLSStatsProtocolErrsThis object reflects the total occurrences,
since link station startup, where this SDLC
link station has inactivated the link as a
result of receiving a frame from its adjacent
link station which was in violation of the
protocol. At link station startup time, this
object must be initialized to zero.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.28 |
sdlcLSStatsActivityTOsThis object reflects the total occurrences,
since startup, where this SDLC link station has
inactivated the link as a result of no activity
on the link. At link station startup time,
this object must be initialized to zero.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.29 |
sdlcLSStatsRNRLIMITsThis object reflects the total occurrences,
since startup, where this SDLC link station has
inactivated the link as a result of its
RNRLIMIT timer expiring. At link station
startup time, this object must be initialized
to zero.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.30 |
sdlcLSStatsRetriesExpsThis object reflects the total occurrences,
since startup, where this SDLC link station has
inactivated the link as a result of a retry
sequence being exhausted. At link station
startup time, this object must be initialized
to zero.ro Counter .1.3.6.1.4.1.43.2.25.2.3.1.31 |
sdlcMapGroup OBJECT IDENTIFIER .1.3.6.1.4.1.43.2.25.3 |
sdlcMapTableThis table contains objects that indicate
how SDLC poll addresses are mapped to LLC2 MAC/SAP
addresses within the router. The mapping indicates
whether the SDLC device is locally or remotely
attached.
This table is proprietary to 3Com Inc. and is
not part of the standard SDLC MIB. SEQUENCE OF SdlcMapEntry .1.3.6.1.4.1.43.2.25.3.1 |
sdlcMapEntryA list of configured values for mappings between
SDLC and LLC2 links. SdlcMapEntry .1.3.6.1.4.1.43.2.25.3.1.1 |
sdlcMapPollAddressThis value is the poll address of the
link station. It uniquely identifies
the SDLC link station to which frames are
to be delivered after traversing the network.ro INTEGER .1.3.6.1.4.1.43.2.25.3.1.1.1 |
sdlcMapLocalMacAddressThe local MAC address with which this control unit
is associated. This address is taken from the
'CULocalMac' UI configuration parameter.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.43.2.25.3.1.1.2 |
sdlcMapLocalSapThe local Service Access Point with which
this control unit is associated. This SAP is
taken from the 'CULocalSap' UI configuration
parameter.ro OCTET STRING .1.3.6.1.4.1.43.2.25.3.1.1.3 |
sdlcMapRemoteMacAddressThe remote MAC address with which this control unit
is associated. This address is taken from the
'CURemoteMac' UI configuration parameter.ro MacAddress (SNMPv2-TC) .1.3.6.1.4.1.43.2.25.3.1.1.4 |
sdlcMapRemoteSapThe remote Service Access Point with which this
control unit is associated. This SAP is taken
from the 'CURemoteSap' UI configuration
parameter.ro OCTET STRING .1.3.6.1.4.1.43.2.25.3.1.1.5 |
sdlcMapNameAn octet string that indicates the name assigned to
the control unit associated with this poll address.ro DisplayString .1.3.6.1.4.1.43.2.25.3.1.1.6 |
sdlcMapPortStateThis object reflects the state of the port
to which this control unit is attached.ro Enumeration .1.3.6.1.4.1.43.2.25.3.1.1.7 |
sdlcMapLSStateThis object reflects the state of the link station
with which this control unit is associated.ro Enumeration .1.3.6.1.4.1.43.2.25.3.1.1.8 |