A3COM-HUAWEI-POWER-ETH-EXT-MIB
AI MIB Summary
The A3COM-HUAWEI-POWER-ETH-EXT-MIB extends monitoring capabilities for Huawei and 3Com Ethernet switches to track external power supply unit status, input voltage levels, and power consumption metrics for PoE-enabled ports. This module enables granular fault detection and capacity planning by exposing real-time electrical parameters and alarm states for redundant power systems and powered devices.
Description.
Main OID:
h3cPowerEthernetExt.1.3.6.1.4.1.43.45.1.10.2.14
129
Objects
Active
Status
5
Dependencies
Imported Objects
Objects
129 total| Object Name |
|---|
h3cPowerEthernetExtDescription. MODULE-IDENTITY .1.3.6.1.4.1.43.45.1.10.2.14 |
h3cPsePortTableThe indexing scheme is taken form that used by the IETF Power MIB. The same indexing scheme is used to give continuity in behaviour between that standard and this extensions definitioin. SEQUENCE OF H3cPsePortEntry .1.3.6.1.4.1.43.45.1.10.2.14.1 |
h3cPsePortEntryThe pethPsePortGroupIndex is imported from the IETF Power MIB and uniquely identifies the group containing the port to which power ethernet PSE is connected. Group means (box in the stack, module in a rack). The pethPsePortPowerIndex is imported from the IETF Power MIB and uniquely identifies the power ethernet PSE port within group pethPseGroupIndex to which the power Ethernet PSE entry is connected. This value will match the local port number on a switch. H3cPsePortEntry .1.3.6.1.4.1.43.45.1.10.2.14.1.1 |
h3cPsePortFaultDescriptionThe object supports the fault category of the IETF Power MIB [1] pethPsePortDetectionStatus object. A textual description containing more information about the nature of this fault is provided by this object. Typically this will detail the precise PoE hardware state which is causing the pethPsePortDetectionStatus object to be in the 'fault' state. It is a DisplayString of up to 255 characters.rw DisplayString (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.14.1.1.2 |
h3cPsePortPeakPowerThe object specifies the peak power which has been consumed by the port. It is defined as the highest measured value of power in milliWatts that has been consumed by the port. Its value is only reset when link is lost, the port is PoE disabled or when it is manually reset by the user asspecified below. It is a read/write integer value with units of milliWatts. Writing a value of zero to this object resets its value to zero. Writing any other value to this object has no effect on its value and an error is returned.rw Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.1.1.3 |
h3cPsePortAveragePowerThe object specifies the average power which has been consumed by the port. This object is a read/write integer value with units of milliWatts. Writing a value of zero to this object resets its value to zero. Writing any other value to this object has no effect on its value and an error is returned.rw Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.1.1.4 |
h3cPsePortCurrentPowerThe object specifies the power currently being consumed by the port. It is a read only integer value with units of milliWatts.ro Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.1.1.5 |
h3cPsePortPowerLimitThe object specifies the power limit set for this port. The PSE will not supply more than this level of power to the specified port. It is a read/write integer value with units of milliWatts.rw Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.1.1.6 |
h3cPsePortProfileIndexIndicates the power profile which is currently associated with this port. This object references the corresponding h3cPseProfileIndex object in the power profiles table. A value of zero is a special case and indicates that no power profile is currently associated with this port. When h3cPseProfileIndex is set to an index of existent profile, pethPsePortPowerPairs, pethPsePortPowerPriority, pethPsePortAdminEnable and h3cPsePortPowerLimit will be set to the same as corresponding value. PethPsePortPowerPairs, pethPsePortPowerPriority and pethPsePortAdminEnable are objects of rfc3621-Power-Ethernet.mib.rw Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.1.1.7 |
h3cMainPseTableDescription. SEQUENCE OF H3cMainPseEntry .1.3.6.1.4.1.43.45.1.10.2.14.2 |
h3cMainPseEntryThe pethMainPseGroupIndex is imported from the IETF Power MIB and uniquely identifies the group containing the port to which power ethernet PSE is connected. Group means (box in the stack, module in a rack) and the value 1 MUST be used for non-modular devices. H3cMainPseEntry .1.3.6.1.4.1.43.45.1.10.2.14.2.1 |
h3cMainPsePowerLimitThe object specifies the power limit set for the unit as a whole. The PoE unit will already have a nominal power defined by the IETF Power MIB [1] pethMainPsePower object. This OPTIONAL object specifies a further limit to this nominal power value. This may be useful to control the thermals of the unit, or for internal testing purposes. One possible use for this object may be to lower the power consumption of the unit if one or more of the internal fans have broken. It is a read/write integer value with units of Watts (note - Watts is chosen instead of milliWatts here since the IETF Power MIB [1] measures unit based parameters, such as the pethMainPsePower object, in units of Watts).rw Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.2.1.1 |
h3cMainPseAveragePowerThe object specifies the average power which has been consumed by the port. It is a read/write integer value with units of Watts (note - Watts is chosen instead of milliWatts here since the IETF Power MIB [1] measures unit based parameters, such as the pethMainPsePower object, in units of Watts). Writing a value of zero to this object resets its value to zero. Writing any other value to this object has no effect on its value and an error is returned.rw Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.2.1.2 |
h3cMainPsePeakPowerThe object specifies the peak power which has been consumed for PoE. It is defined as the highest measured value of power in milliWatts that has been consumed at any one point in time by the sum of the PoE ports. Its value is only reset when the unit is powered on or when it is manually reset by the user as specifiedbelow. It is a read/write integer value with units of Watts (note - Watts is chosen instead of milliWatts here since the IETF Power MIB [1] measures unit based parameters, such as the pethMainPsePower object, in units of Watts). Writing a value of zero to this object resets its value to zero. Writing any other value to this object has noeffect on its value and an error is returned.rw Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.2.1.3 |
h3cMainGuaranteedPowerRemainingThe object specifies the amount of power remaining in the guaranteed power pool. Each time a port is placed into guaranteed mode it reserves a set amount of power out of the total guaranteed power pool for the system. This intention of this object is to give the client of this MIB (whether that be the CLI or the Web interface or the end user) an indication of how many ports can still be placed into guaranteed mode. It is a read only integer value with units of Watts(note - Watts is chosen instead of milliWatts here since the IETF Power MIB [1] measures unit based parameters,such as the pethMainPsePower object, in units of Watts).ro Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.2.1.4 |
h3cMainPsePriorityModeDescribes or controls the priority mode on slot which must be enabled firstly. When a new board is inserted, and the power is over-load, a value of disconnection(0) means that the power will stop supply to the low priority slot ; A value of non-disconnection(1) means that the slot still supply when a new board is inserted, and the power is over-load too.rw Enumeration .1.3.6.1.4.1.43.45.1.10.2.14.2.1.5 |
h3cMainPseLegacyDescribes or controls the legacy mode on slot which must be enabled firstly. Legacy mode: standard or nonstandard PD detection mode.rw Enumeration .1.3.6.1.4.1.43.45.1.10.2.14.2.1.6 |
h3cMainPsePowerPriorityDescribes or controls the priority of the PSE. The priority will be used by the PSE policy to prevent from power overloading. If the priority of PSE is set to critical, the PSE will turn into guaranteed mode. The priority could be used by a control mechanism that prevents power overloading by disconnecting PSEs with lower power priority. PSEs that connect devices critical to the application should be set to higher priority.rw Enumeration .1.3.6.1.4.1.43.45.1.10.2.14.2.1.7 |
h3cPseAutoDetectActiveThe object specifies whether the device auto-detection feature is active. If this object is set to Active, and a known powered device is detected, then the port will automatically switch to Auto-Guaranteed mode. This is a stackwide object (ie. it is not referenced by group index).rw Enumeration .1.3.6.1.4.1.43.45.1.10.2.14.3 |
h3cPseComformance OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.14.4 |
h3cPseCompliances OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.14.4.1 |
h3cPseComplianceDescription. Unknown .1.3.6.1.4.1.43.45.1.10.2.14.4.1.1 |
h3cPseGroup OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.14.4.2 |
h3cPsePortGroupA collection of objects should be supported at the same time. Unknown .1.3.6.1.4.1.43.45.1.10.2.14.4.2.1 |
h3cMainPseGroupA collection of objects should be supported at the same time. Unknown .1.3.6.1.4.1.43.45.1.10.2.14.4.2.2 |
h3cPseScalarGroupA collection of scalar objects supported. Unknown .1.3.6.1.4.1.43.45.1.10.2.14.4.2.3 |
h3cPsePDNotificationGroupPD Change Notification. Unknown .1.3.6.1.4.1.43.45.1.10.2.14.4.2.4 |
h3cPseProfilesGroupA collection of objects should be supported at the same time. Unknown .1.3.6.1.4.1.43.45.1.10.2.14.4.2.5 |
h3cPOEPowerThresholdLimitGroupPower threshold limits group. Unknown .1.3.6.1.4.1.43.45.1.10.2.14.4.2.6 |
h3cPOEPowerSupInfoGroupThe basic Power information group. Unknown .1.3.6.1.4.1.43.45.1.10.2.14.4.2.7 |
h3cPOEPowerDCOutStateGroupThe DC out power state group. Unknown .1.3.6.1.4.1.43.45.1.10.2.14.4.2.8 |
h3cPOEPowerDCOutInfoGroupThe power AC input switch information group Unknown .1.3.6.1.4.1.43.45.1.10.2.14.4.2.9 |
h3cPOEPowerACSwitchStateModuleGroupPD Change Notification. Unknown .1.3.6.1.4.1.43.45.1.10.2.14.4.2.10 |
h3cPOEPowerInCurStateGroupPD Change Notification. Unknown .1.3.6.1.4.1.43.45.1.10.2.14.4.2.11 |
h3cPOEPowerAlarmStateGroupPD Change Notification. Unknown .1.3.6.1.4.1.43.45.1.10.2.14.4.2.12 |
h3cPsePowerMaxValueThe object specifies the max poe power for lanswitch. The value should between the power currently and the max power.rw Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.5 |
h3cpseportNotification OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.14.6 |
h3cpsePDChangeNotificationThis notification indicates if PD has been inserted or pulled out. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.14.6.1 |
h3cPOEDisconnectNotificationThis notification indicates the POE power module does not disconnect. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.14.6.2 |
h3cPOEInputErrorNotificationThis notification indicates the POE power module input error. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.14.6.3 |
h3cPOEOutputErrorNotificationThis notification indicates the POE power module output error. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.14.6.4 |
h3cPOEOverVoltageNotificationThis notification indicates the POE power module overruns the voltage limit. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.14.6.5 |
h3cPOEOverTempNotificationThis notification indicates the POE power module overruns the temperature limit. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.14.6.6 |
h3cPOEFanErrorNotificationThis notification indicates the POE power module fan error. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.14.6.7 |
h3cPOEModuleShutdownNotificationThis notification indicates the POE power module is closed. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.14.6.8 |
h3cPOECurRestrictedNotificationThis notification indicates the POE power module current is restricted. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.14.6.9 |
h3cPOEACSwitchNotificationThis notification indicates the AC input switch alarm of this POE power. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.14.6.10 |
h3cPOEACInCurANotificationThis notification indicates the AC input current A alarm state of this POE power. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.14.6.11 |
h3cPOEACInCurBNotificationThis notification indicates the AC input current B alarm state of this POE power. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.14.6.12 |
h3cPOEACInCurCNotificationThis notification indicates the AC input current C alarm state of this POE power. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.14.6.13 |
h3cPOEACSwitchVolABNotificationThis notification indicates the AC input voltage AB alarm state of this POE power. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.14.6.14 |
h3cPOEACSwitchVolBCNotificationThis notification indicates the AC input voltage BC alarm state of this POE power. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.14.6.15 |
h3cPOEACSwitchVolCANotificationThis notification indicates the AC input voltage CA alarm state of this POE power. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.14.6.16 |
h3cPOEDCOutVolNotificationThis notification indicates the DC output alarm of this POE power. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.14.6.17 |
h3cPOEShutdownNotificationThis notification indicates the whole POE power has been shutdown. NOTIFICATION-TYPE .1.3.6.1.4.1.43.45.1.10.2.14.6.18 |
h3cPseProfilesTableA table of objects representing a set of power profiles. Power profiles can be applied to PoE ports, which have the effect of automatically setting the priority, power limit and PoE enable MIB objects to the values specified in the power profile. SEQUENCE OF H3cPseProfilesEntry .1.3.6.1.4.1.43.45.1.10.2.14.7 |
h3cPseProfilesEntryA set of objects that display and control the Main power of a PSE. H3cPseProfilesEntry .1.3.6.1.4.1.43.45.1.10.2.14.7.1 |
h3cPseProfileIndexThe index of the profile. This uniquely allow the profile to be identified. Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.7.1.1 |
h3cPseProfileNameAssigns the profile a name with which the settings can be assiciated with. For example, 'NBX Phone'.rw DisplayString .1.3.6.1.4.1.43.45.1.10.2.14.7.1.2 |
h3cPseProfilePowerModeThe power mode associated with this power profile. There are two possible power modes as follows: powerDisabled, powerEnabled. When a power profile is applied to a PSE port, this value dictates the settings of the ports pethPsePortPowerPriority and pethPsePortAdminEnable objects.rw Enumeration .1.3.6.1.4.1.43.45.1.10.2.14.7.1.3 |
h3cPseProfilePowerLimitThe power limit to be applied to the ports h3cPsePortPowerLimit object when the profile is applied to the PSE port. Expressed in milliWatts.rw Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.7.1.4 |
h3cPseProfilePriorityThis object controls the priority of the port from the point of view of a power management algorithm. The priority that is set by this variable could be used by a control mechanism that prevents over current situations by disconnecting first ports with lower power priority. Ports that connect devices critical to the operation of the network - like the E911 telephones ports - should be set to higher priority.rw Enumeration .1.3.6.1.4.1.43.45.1.10.2.14.7.1.5 |
h3cPseProfilePairsDescribes or controls the pairs in use. If the value of pethPsePortPowerPairsControl is true, this object is writable. A value of signal(1) means that the signal pairs only are in use. A value of spare(2) means that the spare pairs only are in use.rw Enumeration .1.3.6.1.4.1.43.45.1.10.2.14.7.1.6 |
h3cPseProfileApplyNumThe number of this profile which has been applied. If h3cPseProfileApplyNum is not zero, user can't change the current line.ro Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.7.1.7 |
h3cPseProfileRowStatusThe status of this classifier. If h3cPseProfileApplyNum is not zero, user can't delete the current line.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.14.7.1.8 |
h3cPOEPowerObjects OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.14.8 |
h3cPOEThresholdLimitObjs OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.14.8.1 |
h3cPOEThresholdACMimimumInput threshold AC minimum. It is a read-write node. The value of this node is 'OCTET STRING', it is used to describe a float value. So this string should fit the following rule: 1. This string should be terminated by '\0'; 2. Every characters should be number or radix point; 3. The radix point should occur only once, and it should not be the first or the last character of the string. The value of this node should be smaller than 264.0V and larger than 90.0V. And it should be smaller than the h3cPOEThresholdACMaximum.rw OCTET STRING .1.3.6.1.4.1.43.45.1.10.2.14.8.1.1 |
h3cPOEThresholdACMaximumInput threshold AC maximum. It is a read-write node. The value of this node is 'OCTET STRING', it is used to describe a float value. So this string should fit the following rule: 1. This string should be terminated by '\0'; 2. Every characters should be number or radix point; 3. The radix point should occur only once, and it should not be the first or the last character of the string. It should be smaller than 264.0V and larger than 90.0V. And it should be larger than the h3cPOEThresholdACMinimum.rw OCTET STRING .1.3.6.1.4.1.43.45.1.10.2.14.8.1.2 |
h3cPOEThresholdDCMinimumInput threshold DC minimum. It is a read-write node. The value of this node is 'OCTET STRING', it is used to describe a float value. So this string should fit the following rule: 1. This string should be terminated by '\0'; 2. Every characters should be number or radix point; 3. The radix point should occur only once, and it should not be the first or the last character of the string. It should be smaller than 47.0V and larger than 45.0V.rw OCTET STRING .1.3.6.1.4.1.43.45.1.10.2.14.8.1.3 |
h3cPOEThresholdDCMaximumInput threshold DC maximum. It is a read-write node. The value of this node is 'OCTET STRING', it is used to describe a float value. So this string should fit the following rule: 1. This string should be terminated by '\0'; 2. Every characters should be number or radix point; 3. The radix point should occur only once, and it should not be the first or the last character of the string. It should be smaller than 57.0V and larger than 55.0V.rw OCTET STRING .1.3.6.1.4.1.43.45.1.10.2.14.8.1.4 |
h3cPOESupModuleInfoObjs OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.14.8.2 |
h3cPOEPowerTypeThe type of the power.ro OCTET STRING .1.3.6.1.4.1.43.45.1.10.2.14.8.2.1 |
h3cPOEPowerModuleNumThe number of the power modules.ro Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.8.2.2 |
h3cPOESupervisionModuleNameThe object specifies the Supervision Module name on this POE power.ro OCTET STRING .1.3.6.1.4.1.43.45.1.10.2.14.8.2.3 |
h3cPOESMMajorVersionThe object specifies the high byte of the monitor module version.ro Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.8.2.4 |
h3cPOESMMinorVersionThe object specifies the low byte of the monitor module version.ro Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.8.2.5 |
h3cPOESMFactorNameThe object specifies the name of the manufactor.ro OCTET STRING .1.3.6.1.4.1.43.45.1.10.2.14.8.2.6 |
h3cPOEModuleInfoTableThe table of the module information on this POE power. SEQUENCE OF H3cPOEModuleInfoEntry .1.3.6.1.4.1.43.45.1.10.2.14.8.2.7 |
h3cPOEModuleInfoEntryThe entry of the module information on this POE power. H3cPOEModuleInfoEntry .1.3.6.1.4.1.43.45.1.10.2.14.8.2.7.1 |
h3cPOEModuleIndexThe index of the current module on this POE power. It is also the index of h3cPOEModuleInfoTable. The range of this node is from 1 to h3cPOEPowerModuleNum.ro Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.8.2.7.1.1 |
h3cPOEModuleIDThe ID of the current module on this POE power.ro Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.8.2.7.1.2 |
h3cPOEModuleInfoPowerThe power of the current module on this POE power.ro Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.8.2.7.1.3 |
h3cPOEModuleHardVerInfoThe hardware version information of the current module on this POE power.ro OCTET STRING .1.3.6.1.4.1.43.45.1.10.2.14.8.2.7.1.4 |
h3cPOEDCOutStateObjects OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.14.8.3 |
h3cPOEDCOutStateModuleNumThe module number on this POE power. It is the maximum of the h3cPOEDCOutStateIndex.ro Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.8.3.1 |
h3cPOEDCOutStateTableThe table of DC output power state on this POE power. SEQUENCE OF H3cPOEDCOutStateEntry .1.3.6.1.4.1.43.45.1.10.2.14.8.3.2 |
h3cPOEDCOutStateEntryThe entry of the DC output power state on this POE power. H3cPOEDCOutStateEntry .1.3.6.1.4.1.43.45.1.10.2.14.8.3.2.1 |
h3cPOEDCOutStateIndexThe index of the DC output power state on this POE power. The range of this node is from 1 to h3cPOEDCOutStateModuleNum.ro Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.8.3.2.1.1 |
h3cPOEDCOutDCVolAlarmThe DC output alarm of the DC output power state on this POE power. The value of this node will be the following values: normal (1), underLimit (2), aboveLimit (3), fuseBroken (4), switchOff (5), otherError (6).ro DCAlarmState .1.3.6.1.4.1.43.45.1.10.2.14.8.3.2.1.2 |
h3cPOEDCOutInfoObjects OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.14.8.4 |
h3cPOEDCOutCurNumThe number of DC output current on this POE power. It is the maximum of h3cPOEDCOutInfoIndex.ro Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.8.4.1 |
h3cPOEDCOutInfoTableThe table of the DC output information on this POE power. SEQUENCE OF H3cPOEDCOutInfoEntry .1.3.6.1.4.1.43.45.1.10.2.14.8.4.2 |
h3cPOEDCOutInfoEntryThe entry of the DC output information on this POE power. H3cPOEDCOutInfoEntry .1.3.6.1.4.1.43.45.1.10.2.14.8.4.2.1 |
h3cPOEDCOutInfoIndexThe index of the DC output information on this POE POWER. The range of this node is from 1 to h3cPOEDCOutCurNum.ro Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.8.4.2.1.1 |
h3cPOEDCOutVolThe DC output voltage of the current DC output on this POE power.ro OCTET STRING .1.3.6.1.4.1.43.45.1.10.2.14.8.4.2.1.2 |
h3cPOEDCOutInfoLoadCurThe total load current of the current DC output on this POE power.ro OCTET STRING .1.3.6.1.4.1.43.45.1.10.2.14.8.4.2.1.3 |
h3cPOEACSwitchStateModuleObjs OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.14.8.5 |
h3cPOEACSwitchStateModuleNumThe number of the AC swtich state module on this POE power. It is the maximum of h3cPOEACSwitchStateIndex.ro Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.8.5.1 |
h3cPOEACSwitchStateTableThe table of the AC switch state on this POE power. SEQUENCE OF H3cPOEACSwitchStateEntry .1.3.6.1.4.1.43.45.1.10.2.14.8.5.2 |
h3cPOEACSwitchStateEntryThe entry of the AC switch state on this POE power. H3cPOEACSwitchStateEntry .1.3.6.1.4.1.43.45.1.10.2.14.8.5.2.1 |
h3cPOEACSwitchStateIndexThe index of the AC switch state on this POE power. The range of this node is from 1 to h3cPOEACSwitchStateModuleNum.ro Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.8.5.2.1.1 |
h3cPOEACSwitchStateThe AC switch state on this POE power. The value of this node will be one of the following values: on (1), off (2), highVoltInput (3), lowVoltInput (4)ro SwitchState .1.3.6.1.4.1.43.45.1.10.2.14.8.5.2.1.2 |
h3cPOEInCurStateObjects OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.14.8.6 |
h3cPOEInCurStateModuleNumThe DC input current state of the module on this POE power. It is the maximum of the h3cPOESwitchStateVolExIndex.ro Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.8.6.1 |
h3cPOEInCurAStateThe current A state in the DC input on this POE power. normal (1), underLimit (2), aboveLimit (3), lackPhrase (4), fuseBroken (5), switchOff (6), otherError (7).ro ACAlarmState .1.3.6.1.4.1.43.45.1.10.2.14.8.6.2 |
h3cPOEInCurBStateThe current B state in the DC input on this POE power. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimit (3), lackPhrase (4), fuseBroken (5), switchOff (6), otherError (7).ro ACAlarmState .1.3.6.1.4.1.43.45.1.10.2.14.8.6.3 |
h3cPOEInCurCStateThe current C state in the DC input on this POE power. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimit (3), lackPhrase (4), fuseBroken (5), switchOff (6), otherError (7).ro ACAlarmState .1.3.6.1.4.1.43.45.1.10.2.14.8.6.4 |
h3cPOESwitchStateVolExTableAll alarm status of the VOL status. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimit (3), lackPhrase (4), fuseBroken (5), switchOff (6), otherError (7). SEQUENCE OF H3cPOESwitchStateVolExEntry .1.3.6.1.4.1.43.45.1.10.2.14.8.6.5 |
h3cPOESwitchStateVolExEntryThe h3cPOESwitchStateVolExIndex will match the number of the VOL status. H3cPOESwitchStateVolExEntry .1.3.6.1.4.1.43.45.1.10.2.14.8.6.5.1 |
h3cPOESwitchStateVolExIndexThe object species the index of the VOL status. The range of this node is from 1 to h3cPOEInCurStateModuleNum.ro Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.8.6.5.1.1 |
h3cPOESwitchStateInVolABThe object specifies the VOL AB alarm in each VOL status. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimit (3), lackPhrase (4), fuseBroken (5), switchOff (6), otherError (7).ro ACAlarmState .1.3.6.1.4.1.43.45.1.10.2.14.8.6.5.1.2 |
h3cPOESwitchStateInVolBCThe object specifies the VOL BC alarm in each VOL status. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimit (3), lackPhrase (4), fuseBroken (5), switchOff (6), otherError (7).ro ACAlarmState .1.3.6.1.4.1.43.45.1.10.2.14.8.6.5.1.3 |
h3cPOESwitchStateInVolCAThe object specifies the VOL CA alarm in each VOL status. The value of this node will be one of the following values: normal (1), underLimit (2), aboveLimit (3), lackPhrase (4), fuseBroken (5), switchOff (6), otherError (7).ro ACAlarmState .1.3.6.1.4.1.43.45.1.10.2.14.8.6.5.1.4 |
h3cPOEAlarmStateObjects OBJECT IDENTIFIER .1.3.6.1.4.1.43.45.1.10.2.14.8.7 |
h3cPOEAlarmStateModuleNumThe object specifies the number of the power modules in alarm state.ro Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.8.7.1 |
h3cPOEAlarmStateInfoTableAll alarm states in the POE power modules. SEQUENCE OF H3cPOEAlarmStateInfoEntry .1.3.6.1.4.1.43.45.1.10.2.14.8.7.2 |
h3cPOEAlarmStateInfoEntryThe h3cPOEAlarmModuleInfoIndex will match the number of the power module. H3cPOEAlarmStateInfoEntry .1.3.6.1.4.1.43.45.1.10.2.14.8.7.2.1 |
h3cPOEAlarmModuleInfoIndexThe index specifies the index of the H3cPOEAlarmStateInfoEntry table. The range of this node is from 1 to h3cPOEAlarmStateModuleNum.ro Integer32 .1.3.6.1.4.1.43.45.1.10.2.14.8.7.2.1.1 |
h3cPOEModuleDisconnectThe node specifies the alarm state: The module does not link. The value of this node is one of the following values: normal (1), alarm (2).ro ModuleAlarmState .1.3.6.1.4.1.43.45.1.10.2.14.8.7.2.1.2 |
h3cPOEModuleInputErrorThe node specifies the alarm state: Input error. The value of this node is one of the following values: normal (1), alarm (2).ro ModuleAlarmState .1.3.6.1.4.1.43.45.1.10.2.14.8.7.2.1.3 |
h3cPOEModuleOutputErrorThe node specifies the alarm state: Output error. The value of this node is one of the following values: normal (1), alarm (2).ro ModuleAlarmState .1.3.6.1.4.1.43.45.1.10.2.14.8.7.2.1.4 |
h3cPOEModuleOverVoltageThe node specifies the alarm state: The voltage is too high. The value of this node is one of the following values: normal (1), alarm (2).ro ModuleAlarmState .1.3.6.1.4.1.43.45.1.10.2.14.8.7.2.1.5 |
h3cPOEModuleOverTempThe node specifies the alarm state: The temperature is too high. The value of this node is one of the following values: normal (1), alarm (2).ro ModuleAlarmState .1.3.6.1.4.1.43.45.1.10.2.14.8.7.2.1.6 |
h3cPOEModuleFanErrorThe node specifies the alarm state: The fan error. The value of this node is one of the following values: normal (1), alarm (2).ro ModuleAlarmState .1.3.6.1.4.1.43.45.1.10.2.14.8.7.2.1.7 |
h3cPOEModuleShutdownThe node specifies the alarm state: The module is shutdown. The value of this node is one of the following values: normal (1), alarm (2).ro ModuleAlarmState .1.3.6.1.4.1.43.45.1.10.2.14.8.7.2.1.8 |
h3cPOEModuleCurRestrictedThe node specifies the alarm state: The module limit the current. The value of this node is one of the following values: normal (1), alarm (2).ro ModuleAlarmState .1.3.6.1.4.1.43.45.1.10.2.14.8.7.2.1.9 |
h3cPsePolicyModeThe PSE policy only applies to the situation that when a new board (PSE) is inserted, and the power is overload. A value of priority(2) means that the power will stop supplying to the low priority PSE. About PSE priority, please refer to h3cMainPsePowerPriority. A value of disabled(1) means that the power will stop supplying to the new inserted PSE. The default value of this object is disabled(1).rw Enumeration .1.3.6.1.4.1.43.45.1.10.2.14.9 |
h3cPDPolicyModeThe PD policy only applies to the situation that when a new PD is inserted, and the power of PSE is overload. A value of priority(2) means that the power will stop supplying to the low priority port PD. About port priority, please refer to pethPsePortPowerPriority. A value of disabled(1) means that the slot stop supplying to the new inserted PD. The default value of this object is disabled(1).rw Enumeration .1.3.6.1.4.1.43.45.1.10.2.14.10 |