A3COM-HUAWEI-L4RDT-MIB
AI MIB Summary
The A3COM-HUAWEI-L4RDT-MIB module provides management interfaces for monitoring Layer 4 Routing and Distribution Table (L4RDT) statistics, including session counts, packet throughput, and connection states on Huawei and 3Com network devices. It enables the tracking of specific L4 forwarding metrics and error counters required for troubleshooting traffic distribution and load balancing operations.
See description above
Main OID:
h3cL4Redirect.1.3.6.1.4.1.43.45.1.10.2.10
23
Objects
Active
Status
4
Dependencies
Imported Objects
Objects
23 total| Object Name |
|---|
h3cL4RedirectSee description above MODULE-IDENTITY .1.3.6.1.4.1.43.45.1.10.2.10 |
h3cL4RedirectCacheTableThis table contains an entry for each Web Cache device that this unit is aware of. SEQUENCE OF H3cL4RedirectCacheEntry .1.3.6.1.4.1.43.45.1.10.2.10.1 |
h3cL4RedirectCacheEntryEach row specifies a known Web Cache device. H3cL4RedirectCacheEntry .1.3.6.1.4.1.43.45.1.10.2.10.1.1 |
h3cL4RedirectCacheIpAddressThis object specifies the IP address of the Web Cache device. IpAddress .1.3.6.1.4.1.43.45.1.10.2.10.1.1.1 |
h3cL4RedirectCacheRedirectionStatusThis object returns the current state of traffic redirection to the cache. If redirection is disabled, this object shall return disabledNotRedirecting(1). If a unit cannot be selected to perform the cache health check, this object shall return enabledNoHealthChecker(2). If the software is determining if the cache is able to do redirection(this will happen when the redirection state transitions from disabled to enabled), this object shall return enabledHealthChecking(3). If the cache health check succeeded but the hardware is unable to support redirection to the cache port, this object shall return enabledHealthCheckOKNotRedirecting(4). If the latest health check of the cache has failed, this object shall return enabledHealthCheckFailed(5). If the cache is in use and traffic is being redirected to it, this object shall return enabledRedirecting(6). The default value is disabledNotRedirecting(1).ro Enumeration .1.3.6.1.4.1.43.45.1.10.2.10.1.1.2 |
h3cL4RedirectCachePortThis object stores the ifIndex that identifies the port or link aggregation which provides the connection that leads to the cache. If only manual cache configuration is supported, this value must be supplied. The method of cache configuration can be ascertained by the presence or absence of the L4 manual cache configuration id within the 3com-352 MIB. The default value is 0.rw INTEGER .1.3.6.1.4.1.43.45.1.10.2.10.1.1.3 |
h3cL4RedirectCacheRowStatusThis object is used to create and remove Web Cache entries. The following are the valid values that may be written to RowStatus: Writing createAndGo(4) to the RowStatus of a non-existent row shall create a row with default values and shall set the row to active(1). If the row already exists, it shall be an error. Writing createAndWait(5) to the RowStatus of a non-existent row shall create a row with default values and shall set the row to notInService(2). If the row already exists, it shall be an error. Writing active(1) to the RowStatus of an existing row shall change the value of that row to active(1). Writing active(1) to the RowStatus of an existing row that is already active(1) shall not cause an error, the row shall remain active(1). If the row does not exist, it shall be an error. Writing notInService(2) to the RowStatus of an existing row shall change the value of that row to notInService(2). Writing notInService(2) to the RowStatus of an existing row that is already notInService(2) shall not cause an error, the row shall remain notInService(2). If the row does not exist, it shall be an error. Writing destroy(6) to the RowStatus of a non-existent row shall be an error. If the row exists, it shall be removed. Writing notReady(3) to the RowStatus of a non-existent row or to an existent row shall be an error. If the user does not supply values for the necessary objects, default values will be supplied. Attempts to create more entries than the hardware can support shall be rejected.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.10.1.1.4 |
h3cL4RedirectCacheMacAddressThis object defines the MAC address of the attached Web cache device. If only manual configuration of the cache is supported, this value must be supplied. The method of cache configuration can be ascertained by the presence or absence of the L4 manual cache configuration id within the 3com-352 MIB. The default value is 0.rw MacAddress (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.10.1.1.5 |
h3cL4RedirectCacheVlanThis object specifies the VLAN which the cache port belongs to.rw INTEGER .1.3.6.1.4.1.43.45.1.10.2.10.1.1.6 |
h3cL4RedirectCacheTcpPortThis object specifies the TCP port number that is being redirectedrw INTEGER .1.3.6.1.4.1.43.45.1.10.2.10.1.1.7 |
h3cL4RedirectIpExclusionTableThis table lists the IP addresses and subnetworks that Web Cache redirection is not supported for. Some devices may not support addition to this table. SEQUENCE OF H3cL4RedirectIpExclusionEntry .1.3.6.1.4.1.43.45.1.10.2.10.2 |
h3cL4RedirectIpExclusionEntryEach row contains an IP address or a IP subnetwork that is being excluded from the redirection. H3cL4RedirectIpExclusionEntry .1.3.6.1.4.1.43.45.1.10.2.10.2.1 |
h3cL4RedirectIpExclusionIpAddressThis object specifies the IP address or the subnetwork address that is to be excluded. IpAddress .1.3.6.1.4.1.43.45.1.10.2.10.2.1.1 |
h3cL4RedirectIpExclusionMaskLenThis object provides the number of bits in the subnetwork mask. This mask shall be applied to the excludeIP address to determine the subnetwork that is to be excluded. A value of 32 implies that the excludeIP address refers to an individual host. The default value is 32.rw INTEGER .1.3.6.1.4.1.43.45.1.10.2.10.2.1.2 |
h3cL4RedirectIpExclusionRowStatusThis object is used to add rows to the Exclusion Table. The following are the valid values that may be written to RowStatus: Writing createAndGo(4) to the RowStatus of a non-existent row shall create a new row. The new row shall be active(1). If the row exists, it shall be an error. Writing createAndWait(5) to the RowStatus of a non-existent row or to an existent row shall be an error. Writing active(1) to the RowStatus of an existing row shall change the value of that row to active(1). Writing active(1) to the RowStatus of an existing row that is already active(1) shall not cause an error, the row shall remain active(1). If the row does not exist, it shall be an error. Writing notInService(2) to the RowStatus of an existing row shall change the value of that row to notInService(2). Writing notInService(2) to the RowStatus of an existing row that is already notInService(2) shall not cause an error, the row shall remain notInService(2). If the row does not exist, it shall be an error. Writing destroy(6) to the RowStatus of a non-existent row shall be an error. If the row exists, it shall be removed. Writing notReady(3) to the RowStatus of a non-existent row or to an existent row shall be an error. Attempts to create more entries than the hardware can support shall be rejected.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.10.2.1.3 |
h3cL4RedirectVlanTableThis table contains a row for each VLAN of the packet which need to be redirected to the Web cache. SEQUENCE OF H3cL4RedirectVlanEntry .1.3.6.1.4.1.43.45.1.10.2.10.3 |
h3cL4RedirectVlanEntryEach row specifies a VLAN of the packet which need to be redirected to the Web cache. H3cL4RedirectVlanEntry .1.3.6.1.4.1.43.45.1.10.2.10.3.1 |
h3cL4RedirectVlanIDThis object specifies the VLAN ID of the packet which need to be redirected to the Web cache. INTEGER .1.3.6.1.4.1.43.45.1.10.2.10.3.1.1 |
h3cL4RedirectVlanRowStatusThis object allows ports to be added and removed from the table. The following are the valid values that may be written to RowStatus: Writing createAndGo(4) to the RowStatus of a non-existent row shall create a new row. The new row shall be active(1). If the row exists, it shall be an error. Writing createAndWait(5) to the RowStatus of a non-existent row or to an existent row shall be an error. Writing active(1) to the RowStatus of an existing row shall change the value of that row to active(1). Writing active(1) to the RowStatus of an existing row that is already active(1) shall not cause an error, the row shall remain active(1). If the row does not exist, it shall be an error. Writing notInService(2) to the RowStatus of a non-existent row or to an existent row shall be an error. Writing destroy(6) to the RowStatus of a non-existent row shall be an error. If the row exists, it shall be removed. Writing notReady(3) to the RowStatus of a non-existent row or to an existent row shall be an error. Attempts to create more entries than the hardware can support shall be rejected.rw RowStatus (SNMPv2-TC) .1.3.6.1.4.1.43.45.1.10.2.10.3.1.2 |
h3cL4RedirectInformationStringThis object shall contain the string generated as a result of a Layer 4 Redirection configuration. It shall contain either a string describing successful configuration or a string describing unsuccessful configuration. This length of this string shall be no longer than 80 characters.ro DisplayString .1.3.6.1.4.1.43.45.1.10.2.10.4 |
h3cL4RedirectFreeCacheEntriesThis object indicates the number of entries that may still be added to the h3cL4RedirectCacheTable.ro INTEGER .1.3.6.1.4.1.43.45.1.10.2.10.5 |
h3cL4RedirectFreeIpExclusionEntriesThis object indicates the number of entries that may still be added to the h3cL4RedirectIpExclusionTable.ro INTEGER .1.3.6.1.4.1.43.45.1.10.2.10.6 |
h3cL4RedirectFreeVlanEntriesThis object indicates the number of entries that may still be added to the h3cL4RedirectVlanTable.ro INTEGER .1.3.6.1.4.1.43.45.1.10.2.10.7 |
More MIBs from 3Com
Browse all 3ComMIBs →A3Com-products-MIB
Standard SNMP MIB module defining data structures for A3Com-products-MIB.
1546 objects→
A3COM-HUAWEI-ENTITY-VENDORTYPE-OID-MIB
The A3COM-HUAWEI-ENTITY-VENDORTYPE-OID-MIB defines vendor-specific object identifiers for H3C (Huawei) hardware to map physical components within the ENTITY-MIB's entPhysicalTable, enabling precise differentiation of device types and sub-components during SNMP-based inventory and topology discovery.
1462 objects→
A3COM-HUAWEI-CBQOS2-MIB
The A3COM-HUAWEI-CBQOS2-MIB enables configuration and runtime monitoring of Class-Based QoS (CBQoS) policies on H3C and Huawei network devices, specifically tracking classifier definitions, traffic matching rules, behavior actions (CAR, GTS, WRED, remarking), and policy application status across interfaces, VLANs, ATM PVCs, and Frame Relay PVCs.
472 objects→
A3COM-HUAWEI-DOT11-APMT-MIB
The A3COM-HUAWEI-DOT11-APMT-MIB module monitors and manages A3COM and Huawei wireless Access Points (APs) by exposing real-time operational objects and statistical counters for 802.11 radio interfaces, association states, and BSS metrics. This MIB facilitates the collection of performance data and device status required for monitoring AP health, client association counts, and traffic statistics in both Fat and Fit AP deployment architectures.
472 objects→
A3COM-SWITCHING-SYSTEMS-MIB
Standard SNMP MIB module defining data structures for A3COM-SWITCHING-SYSTEMS-MIB.
425 objects→
A3COM-HUAWEI-EPON-MIB
The A3COM-HUAWEI-EPON-MIB module enables monitoring and configuration of Ethernet Passive Optical Network (EPON) ports on A3COM and Huawei devices, specifically tracking EFM PON parameters defined in IEEE Draft P802.3ah clauses 60, 64, and 65. This includes managing optical line terminal (OLT) and optical network unit (ONU) session states, port configurations, and physical layer statistics for fiber access networks.
424 objects→